forked from xuos/xiuos
chunyexixiaoyu
240 lines
6.2 KiB
Plaintext
240 lines
6.2 KiB
Plaintext
menu "Board Drivers Config"
|
|
|
|
config BSP_USING_UART_HS
|
|
bool "Enable High Speed UART"
|
|
default y
|
|
|
|
|
|
menu "General Purpose UARTs"
|
|
menuconfig BSP_USING_UART1
|
|
bool "Enable UART1"
|
|
default n
|
|
if BSP_USING_UART1
|
|
config BSP_UART1_TXD_PIN
|
|
int "uart1 TXD pin number"
|
|
default 20
|
|
config BSP_UART1_RXD_PIN
|
|
int "uart1 RXD pin number"
|
|
default 21
|
|
config BSP_UART1_RTS_PIN
|
|
int "uart1 RTS pin number (-1 for not used)"
|
|
default -1
|
|
config BSP_UART1_CTS_PIN
|
|
int "uart1 CTS pin number (-1 for not used)"
|
|
default -1
|
|
endif
|
|
|
|
menuconfig BSP_USING_UART2
|
|
bool "Enable UART2"
|
|
default n
|
|
if BSP_USING_UART2
|
|
config BSP_UART2_TXD_PIN
|
|
int "uart2 TXD pin number"
|
|
default 28
|
|
config BSP_UART2_RXD_PIN
|
|
int "uart2 RXD pin number"
|
|
default 27
|
|
config BSP_UART2_RTS_PIN
|
|
int "uart2 RTS pin number (-1 for not used)"
|
|
default -1
|
|
config BSP_UART2_CTS_PIN
|
|
int "uart2 CTS pin number (-1 for not used)"
|
|
default -1
|
|
endif
|
|
|
|
menuconfig BSP_USING_UART3
|
|
bool "Enable UART3"
|
|
default n
|
|
if BSP_USING_UART3
|
|
config BSP_UART3_TXD_PIN
|
|
int "uart3 TXD pin number"
|
|
default 22
|
|
config BSP_UART3_RXD_PIN
|
|
int "uart3 RXD pin number"
|
|
default 23
|
|
config BSP_UART3_RTS_PIN
|
|
int "uart3 RTS pin number (-1 for not used)"
|
|
default -1
|
|
config BSP_UART3_CTS_PIN
|
|
int "uart3 CTS pin number (-1 for not used)"
|
|
default -1
|
|
endif
|
|
endmenu
|
|
|
|
config BSP_USING_I2C1
|
|
bool "Enable I2C1 (GPIO0/1)"
|
|
select RT_USING_I2C
|
|
default n
|
|
|
|
menuconfig BSP_USING_SPI1
|
|
bool "Enable SPI1"
|
|
select RT_USING_SPI
|
|
default n
|
|
if BSP_USING_SPI1
|
|
config BSP_USING_SPI1_AS_QSPI
|
|
bool
|
|
default n
|
|
config BSP_SPI1_CLK_PIN
|
|
int "spi1 clk pin number"
|
|
default 27
|
|
config BSP_SPI1_D0_PIN
|
|
int "spi1 d0 pin number"
|
|
default 28
|
|
config BSP_SPI1_D1_PIN
|
|
int "spi1 d1 pin number"
|
|
default 26
|
|
if BSP_USING_SPI1_AS_QSPI
|
|
config BSP_SPI1_D2_PIN
|
|
int "spi1 d2 pin number"
|
|
default 32
|
|
config BSP_SPI1_D3_PIN
|
|
int "spi1 d3 pin number"
|
|
default 33
|
|
endif
|
|
menuconfig BSP_SPI1_USING_SS0
|
|
bool "SPI1 Enable SS0(spi10 dev)"
|
|
default n
|
|
if BSP_SPI1_USING_SS0
|
|
config BSP_SPI1_SS0_PIN
|
|
int "spi1 ss0 pin number"
|
|
default 29
|
|
endif
|
|
menuconfig BSP_SPI1_USING_SS1
|
|
bool "SPI1 Enable SS1(spi11 dev)"
|
|
default n
|
|
if BSP_SPI1_USING_SS1
|
|
config BSP_SPI1_SS1_PIN
|
|
int "spi1 ss1 pin number"
|
|
default 8
|
|
endif
|
|
menuconfig BSP_SPI1_USING_SS2
|
|
bool "SPI1 Enable SS2(spi12 dev)"
|
|
default n
|
|
if BSP_SPI1_USING_SS2
|
|
config BSP_SPI1_SS2_PIN
|
|
int "spi1 ss2 pin number"
|
|
default 26
|
|
endif
|
|
menuconfig BSP_SPI1_USING_SS3
|
|
bool "SPI1 Enable SS3(spi13 dev)"
|
|
default n
|
|
if BSP_SPI1_USING_SS3
|
|
config BSP_SPI1_SS3_PIN
|
|
int "spi1 ss3 pin number"
|
|
default 27
|
|
endif
|
|
endif
|
|
|
|
menuconfig BSP_USING_LCD
|
|
bool "Enable LCD on SPI0"
|
|
default n
|
|
|
|
if BSP_USING_LCD
|
|
config BSP_LCD_CS_PIN
|
|
int "CS pin number of 8080 interface"
|
|
default 36
|
|
config BSP_LCD_WR_PIN
|
|
int "WR pin number of 8080 interface"
|
|
default 39
|
|
config BSP_LCD_DC_PIN
|
|
int "DC pin number of 8080 interface"
|
|
default 38
|
|
config BSP_LCD_RST_PIN
|
|
int "RESET pin number of 8080 interface (-1 for not used)"
|
|
default 37
|
|
config BSP_LCD_BACKLIGHT_PIN
|
|
int "Backlight control pin number (-1 for not used)"
|
|
default -1
|
|
choice
|
|
prompt "backlight active polarity"
|
|
default BSP_LCD_BACKLIGHT_ACTIVE_LOW
|
|
|
|
config BSP_LCD_BACKLIGHT_ACTIVE_LOW
|
|
bool "lcd backlight on low level"
|
|
config BSP_LCD_BACKLIGHT_ACTIVE_HIGH
|
|
bool "lcd_backlight on high level"
|
|
endchoice
|
|
|
|
config BSP_LCD_CLK_FREQ
|
|
int "Lcd max clk frequency"
|
|
default 15000000
|
|
|
|
choice
|
|
prompt "lcd scan direction"
|
|
default BSP_BOARD_KD233
|
|
|
|
config BSP_BOARD_KD233
|
|
bool "board_kd233 lcd scan: DIR_YX_RLUD"
|
|
|
|
config BSP_BOARD_K210_OPENMV_TEST
|
|
bool "board_k210_openmv lcd scan: DIR_YX_LRUD"
|
|
|
|
config BSP_BOARD_USER
|
|
bool "board_user: user defined."
|
|
endchoice
|
|
|
|
config BSP_LCD_X_MAX
|
|
int "LCD Height"
|
|
default 240
|
|
config BSP_LCD_Y_MAX
|
|
int "LCD Width"
|
|
default 320
|
|
endif
|
|
|
|
menuconfig BSP_USING_SDCARD
|
|
bool "Enable SDCARD (spi1(ss0))"
|
|
select BSP_USING_SPI1
|
|
select BSP_SPI1_USING_SS0
|
|
select RT_USING_DFS
|
|
select RT_USING_DFS_ELMFAT
|
|
select RT_USING_SPI_MSD
|
|
default n
|
|
|
|
|
|
menuconfig BSP_USING_DVP
|
|
bool "Enable DVP(camera)"
|
|
default n
|
|
|
|
if BSP_USING_DVP
|
|
comment "The default pin assignment is based on the Maix Duino K210 development board"
|
|
config BSP_DVP_SCCB_SDA_PIN
|
|
int "SCCB SDA pin number for camera"
|
|
default 40
|
|
config BSP_DVP_SCCB_SCLK_PIN
|
|
int "SCCB SCLK pin number for camera"
|
|
default 41
|
|
config BSP_DVP_CMOS_RST_PIN
|
|
int "CMOS RST pin number for camera"
|
|
default 42
|
|
config BSP_DVP_CMOS_VSYNC_PIN
|
|
int "CMOS VSYNC pin number for camera"
|
|
default 43
|
|
config BSP_DVP_CMOS_PWDN_PIN
|
|
int "CMOS PWDN pin number for camera"
|
|
default 44
|
|
config BSP_DVP_CMOS_XCLK_PIN
|
|
int "CMOS XCLK pin number for camera"
|
|
default 46
|
|
config BSP_DVP_CMOS_PCLK_PIN
|
|
int "CMOS PCLK pin number for camera"
|
|
default 47
|
|
config BSP_DVP_CMOS_HREF_PIN
|
|
int "CMOS HREF pin number for camera"
|
|
default 45
|
|
endif
|
|
|
|
if PKG_USING_RW007
|
|
config RW007_SPIDEV_NAME
|
|
string "the SPIDEV rw007 driver on"
|
|
default "spi11"
|
|
config RW007_INT_BUSY_PIN
|
|
int "rw007 int pin for rw007"
|
|
default 7
|
|
config RW007_RST_PIN
|
|
int "rw007 rst pin for rw007"
|
|
default 6
|
|
endif
|
|
|
|
|
|
endmenu
|