From 2f3ded2a1122056f0d5c8755adeea44a0497fcd5 Mon Sep 17 00:00:00 2001 From: linzewen Date: Tue, 6 Apr 2021 20:18:12 -0700 Subject: [PATCH] Add makefile based project for Nuclei RV_STAR board Setup tools for compilment and entering GCC folder under riscv_nuclei_gd32vf103_soc_gcc Using "make all" command to compile project Using "make clean" command to clean project Using "make debug" command to debug project Using "make upload" command to upload project OS configurations is under "OS_CONFIG" folder Most information can be found in README.md Signed-off-by: linzewen --- .../riscv_nuclei_gd32vf103_soc_gcc/.gitignore | 9 + .../GCC/Makefile | 224 ++ .../GCC/gcc_gd32vf103_flashxip.ld | 289 +++ .../GCC/liteos_m.mk | 38 + .../GCC/openocd_gd32vf103.cfg | 53 + .../OS_CONFIG/target_config.h | 118 + .../riscv_nuclei_gd32vf103_soc_gcc/README.md | 203 ++ .../Include/gd32vf103v_rvstar.h | 134 ++ .../Include/nuclei_sdk_hal.h | 20 + .../Source/gd32vf103v_rvstar.c | 191 ++ .../Common/Include/Usb/drv_usb_core.h | 117 + .../Common/Include/Usb/drv_usb_dev.h | 217 ++ .../Common/Include/Usb/drv_usb_host.h | 175 ++ .../gd32vf103/Common/Include/Usb/drv_usb_hw.h | 61 + .../Common/Include/Usb/drv_usb_regs.h | 666 ++++++ .../Common/Include/Usb/drv_usbd_int.h | 52 + .../Common/Include/Usb/drv_usbh_int.h | 49 + .../Common/Include/Usb/usb_ch9_std.h | 250 +++ .../gd32vf103/Common/Include/Usb/usb_conf.h | 101 + .../gd32vf103/Common/Include/Usb/usbd_conf.h | 10 + .../gd32vf103/Common/Include/Usb/usbd_core.h | 95 + .../gd32vf103/Common/Include/Usb/usbd_enum.h | 114 + .../Common/Include/Usb/usbd_transc.h | 64 + .../gd32vf103/Common/Include/Usb/usbh_conf.h | 9 + .../gd32vf103/Common/Include/Usb/usbh_core.h | 219 ++ .../gd32vf103/Common/Include/Usb/usbh_enum.h | 78 + .../gd32vf103/Common/Include/Usb/usbh_pipe.h | 70 + .../Common/Include/Usb/usbh_transc.h | 54 + .../SoC/gd32vf103/Common/Include/gd32vf103.h | 390 ++++ .../gd32vf103/Common/Include/gd32vf103_adc.h | 399 ++++ .../gd32vf103/Common/Include/gd32vf103_bkp.h | 229 ++ .../gd32vf103/Common/Include/gd32vf103_can.h | 720 ++++++ .../gd32vf103/Common/Include/gd32vf103_crc.h | 80 + .../gd32vf103/Common/Include/gd32vf103_dac.h | 244 ++ .../gd32vf103/Common/Include/gd32vf103_dbg.h | 111 + .../gd32vf103/Common/Include/gd32vf103_dma.h | 285 +++ .../gd32vf103/Common/Include/gd32vf103_exmc.h | 129 ++ .../gd32vf103/Common/Include/gd32vf103_exti.h | 248 +++ .../gd32vf103/Common/Include/gd32vf103_fmc.h | 314 +++ .../Common/Include/gd32vf103_fwdgt.h | 107 + .../gd32vf103/Common/Include/gd32vf103_gpio.h | 423 ++++ .../gd32vf103/Common/Include/gd32vf103_i2c.h | 344 +++ .../Common/Include/gd32vf103_libopt.h | 59 + .../gd32vf103/Common/Include/gd32vf103_pmu.h | 127 ++ .../gd32vf103/Common/Include/gd32vf103_rcu.h | 760 +++++++ .../gd32vf103/Common/Include/gd32vf103_rtc.h | 150 ++ .../gd32vf103/Common/Include/gd32vf103_spi.h | 343 +++ .../Common/Include/gd32vf103_timer.h | 724 ++++++ .../Common/Include/gd32vf103_usart.h | 378 ++++ .../Common/Include/gd32vf103_wwdgt.h | 88 + .../gd32vf103/Common/Include/nuclei_sdk_soc.h | 16 + .../Common/Include/system_gd32vf103.h | 80 + .../Common/Source/Drivers/Usb/drv_usb_core.c | 319 +++ .../Common/Source/Drivers/Usb/drv_usb_dev.c | 749 +++++++ .../Common/Source/Drivers/Usb/drv_usb_host.c | 514 +++++ .../Common/Source/Drivers/Usb/drv_usbd_int.c | 595 +++++ .../Common/Source/Drivers/Usb/drv_usbh_int.c | 536 +++++ .../Source/Drivers/Usb/gd32vf103_usb_hw.c | 265 +++ .../Common/Source/Drivers/Usb/usbd_core.c | 329 +++ .../Common/Source/Drivers/Usb/usbd_enum.c | 696 ++++++ .../Common/Source/Drivers/Usb/usbd_transc.c | 254 +++ .../Common/Source/Drivers/Usb/usbh_core.c | 441 ++++ .../Common/Source/Drivers/Usb/usbh_enum.c | 549 +++++ .../Common/Source/Drivers/Usb/usbh_pipe.c | 174 ++ .../Common/Source/Drivers/Usb/usbh_transc.c | 391 ++++ .../Common/Source/Drivers/gd32vf103_adc.c | 994 +++++++++ .../Common/Source/Drivers/gd32vf103_bkp.c | 292 +++ .../Common/Source/Drivers/gd32vf103_can.c | 989 +++++++++ .../Common/Source/Drivers/gd32vf103_crc.c | 127 ++ .../Common/Source/Drivers/gd32vf103_dac.c | 537 +++++ .../Common/Source/Drivers/gd32vf103_dbg.c | 110 + .../Common/Source/Drivers/gd32vf103_dma.c | 731 ++++++ .../Common/Source/Drivers/gd32vf103_exmc.c | 164 ++ .../Common/Source/Drivers/gd32vf103_exti.c | 254 +++ .../Common/Source/Drivers/gd32vf103_fmc.c | 649 ++++++ .../Common/Source/Drivers/gd32vf103_fwdgt.c | 151 ++ .../Common/Source/Drivers/gd32vf103_gpio.c | 502 +++++ .../Common/Source/Drivers/gd32vf103_i2c.c | 726 ++++++ .../Common/Source/Drivers/gd32vf103_pmu.c | 263 +++ .../Common/Source/Drivers/gd32vf103_rcu.c | 1103 +++++++++ .../Common/Source/Drivers/gd32vf103_rtc.c | 273 +++ .../Common/Source/Drivers/gd32vf103_spi.c | 766 +++++++ .../Common/Source/Drivers/gd32vf103_timer.c | 1967 +++++++++++++++++ .../Common/Source/Drivers/gd32vf103_usart.c | 781 +++++++ .../Common/Source/Drivers/gd32vf103_wwdgt.c | 146 ++ .../Common/Source/GCC/intexc_gd32vf103.S | 232 ++ .../Common/Source/GCC/startup_gd32vf103.S | 370 ++++ .../Common/Source/Stubs/clock_getres.c | 14 + .../Common/Source/Stubs/clock_gettime.c | 21 + .../Common/Source/Stubs/clock_settime.c | 10 + .../SoC/gd32vf103/Common/Source/Stubs/close.c | 12 + .../gd32vf103/Common/Source/Stubs/execve.c | 12 + .../SoC/gd32vf103/Common/Source/Stubs/exit.c | 9 + .../SoC/gd32vf103/Common/Source/Stubs/fork.c | 12 + .../SoC/gd32vf103/Common/Source/Stubs/fstat.c | 19 + .../gd32vf103/Common/Source/Stubs/getpid.c | 8 + .../Common/Source/Stubs/gettimeofday.c | 15 + .../gd32vf103/Common/Source/Stubs/isatty.c | 8 + .../SoC/gd32vf103/Common/Source/Stubs/kill.c | 11 + .../SoC/gd32vf103/Common/Source/Stubs/link.c | 12 + .../SoC/gd32vf103/Common/Source/Stubs/lseek.c | 11 + .../SoC/gd32vf103/Common/Source/Stubs/open.c | 12 + .../SoC/gd32vf103/Common/Source/Stubs/read.c | 22 + .../SoC/gd32vf103/Common/Source/Stubs/sbrk.c | 19 + .../SoC/gd32vf103/Common/Source/Stubs/stat.c | 9 + .../SoC/gd32vf103/Common/Source/Stubs/times.c | 27 + .../gd32vf103/Common/Source/Stubs/unlink.c | 12 + .../SoC/gd32vf103/Common/Source/Stubs/wait.c | 13 + .../SoC/gd32vf103/Common/Source/Stubs/write.c | 22 + .../gd32vf103/Common/Source/gd32vf103_soc.c | 59 + .../Common/Source/system_gd32vf103.c | 584 +++++ .../riscv_nuclei_gd32vf103_soc_gcc/Src/main.c | 49 + .../Src/task_sample.c | 121 + .../Src/task_sample.h | 54 + .../doc/image/nuclei_tools_download_linux.png | Bin 0 -> 41868 bytes 115 files changed, 29544 insertions(+) create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/.gitignore create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/Makefile create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/gcc_gd32vf103_flashxip.ld create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/liteos_m.mk create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/openocd_gd32vf103.cfg create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/OS_CONFIG/target_config.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/README.md create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/gd32vf103v_rvstar.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/nuclei_sdk_hal.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Source/gd32vf103v_rvstar.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_core.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_dev.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_host.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_hw.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_regs.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbd_int.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbh_int.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_ch9_std.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_conf.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_conf.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_core.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_enum.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_transc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_conf.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_core.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_enum.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_pipe.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_transc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_adc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_bkp.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_can.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_crc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dac.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dbg.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dma.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exmc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exti.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fmc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fwdgt.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_gpio.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_i2c.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_libopt.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_pmu.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rcu.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rtc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_spi.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_timer.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_usart.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_wwdgt.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/nuclei_sdk_soc.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/system_gd32vf103.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_core.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_dev.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_host.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbd_int.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbh_int.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/gd32vf103_usb_hw.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_core.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_enum.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_transc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_core.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_enum.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_pipe.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_transc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_adc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_bkp.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_can.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_crc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dac.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dbg.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dma.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exmc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exti.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fmc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fwdgt.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_gpio.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_i2c.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_pmu.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rcu.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rtc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_spi.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_timer.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_usart.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_wwdgt.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/intexc_gd32vf103.S create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/startup_gd32vf103.S create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_getres.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_gettime.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_settime.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/close.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/execve.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/exit.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fork.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fstat.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/getpid.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/gettimeofday.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/isatty.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/kill.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/link.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/lseek.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/open.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/read.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/sbrk.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/stat.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/times.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/unlink.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/wait.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/write.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/gd32vf103_soc.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/system_gd32vf103.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/Src/main.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.c create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.h create mode 100644 targets/riscv_nuclei_gd32vf103_soc_gcc/doc/image/nuclei_tools_download_linux.png diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/.gitignore b/targets/riscv_nuclei_gd32vf103_soc_gcc/.gitignore new file mode 100644 index 00000000..2395b36e --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/.gitignore @@ -0,0 +1,9 @@ +# ignore openocd logfile and build folder +targets/*/GCC/build/ +*.log +*.lst +*.bin +*.dasm +*.elf +*.hex +*.map \ No newline at end of file diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/Makefile b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/Makefile new file mode 100644 index 00000000..2405a7a2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/Makefile @@ -0,0 +1,224 @@ +# ------------------------------------------------ +# Generic Makefile (based on gcc) +# +# ChangeLog : +# 2021-04-02 - first version +# ------------------------------------------------ + +###################################### +# target +###################################### +TARGET = Nuclei-rvstar-gd32vf103-soc + +###################################### +# building variables +###################################### +# debug build? +DEBUG = 1 +# optimization +OPT = -O2 + + +####################################### +# paths +####################################### +# Build path +BUILD_DIR = build + +####################################### +# Base directory +####################################### +# LiteOS top path +LITEOSTOPDIR := ../../../ + +###################################### +# source +###################################### +# C sources +C_SOURCES = \ +$(wildcard ../Src/*.c) \ +$(wildcard ../SoC/gd32vf103/Common/Source/*.c) \ +$(wildcard ../SoC/gd32vf103/Board/gd32vf103v_rvstar/Source/*.c) \ +$(wildcard ../SoC/gd32vf103/Common/Source/Drivers/*.c) \ +$(wildcard ../SoC/gd32vf103/Common/Source/Drivers/Usb/*.c) \ +$(wildcard ../SoC/gd32vf103/Common/Source/Stubs/*.c) + +# ASM sources +ASMS_SOURCES = \ +$(wildcard ../SoC/gd32vf103/Common/Source/GCC/*.S) + +####################################### +# binaries +####################################### +PREFIX = riscv-nuclei-elf- +# The gcc compiler bin path can be either defined in make command via NUCLEI_TOOL_ROOT variable (> make NUCLEI_TOOL_ROOT=xxx) +# either it can be added to the PATH environment variable. +NUCLEI_RISCV_GCC_ROOT ?= $(NUCLEI_TOOL_ROOT)/gcc +NUCLEI_OPENOCD_ROOT ?= $(NUCLEI_TOOL_ROOT)/openocd + +NUCLEI_TOOL_ROOT_EXIST = 0 +ifneq ($(wildcard $(NUCLEI_RISCV_GCC_ROOT)),) +ifneq ($(wildcard $(NUCLEI_OPENOCD_ROOT)),) +NUCLEI_TOOL_ROOT_EXIST = 1 +endif +endif + +ifeq ($(NUCLEI_TOOL_ROOT_EXIST),1) +CC = $(NUCLEI_RISCV_GCC_ROOT)/bin/$(PREFIX)gcc +AS = $(NUCLEI_RISCV_GCC_ROOT)/bin/$(PREFIX)gcc -x assembler-with-cpp +CP = $(NUCLEI_RISCV_GCC_ROOT)/bin/$(PREFIX)objcopy +DP = $(NUCLEI_RISCV_GCC_ROOT)/bin/$(PREFIX)objdump +SZ = $(NUCLEI_RISCV_GCC_ROOT)/bin/$(PREFIX)size +GDB = $(NUCLEI_RISCV_GCC_ROOT)/bin/$(PREFIX)gdb +OPENOCD := $(NUCLEI_OPENOCD_ROOT)/bin/openocd +else +CC = $(PREFIX)gcc +AS = $(PREFIX)gcc -x assembler-with-cpp +CP = $(PREFIX)objcopy +DP = $(PREFIX)objdump +SZ = $(PREFIX)size +GDB = $(PREFIX)gdb +OPENOCD := openocd +endif +HEX = $(CP) -O ihex +BIN = $(CP) -O binary -S + +ECHO := echo + +OPENOCD_CFG := openocd_gd32vf103.cfg + +####################################### +# CFLAGS +####################################### +#risc-v arch & abi +CORE_ARCH_ABI = -march=rv32imac -mabi=ilp32 + +#other flags +OTHER_FLAGS += -g -mcmodel=medany -fno-common + +# macros for gcc +# AS defines +AS_DEFS = -DDOWNLOAD_MODE=DOWNLOAD_MODE_FLASHXIP + +# C defines +C_DEFS = -DDOWNLOAD_MODE=DOWNLOAD_MODE_FLASHXIP + + +# AS includes +AS_INCLUDES = + +# C includes +C_INCLUDES = \ +-I../OS_CONFIG \ +-I../Src \ +-I../SoC/gd32vf103/Board/gd32vf103v_rvstar/Include \ +-I../SoC/gd32vf103/Common/Include \ +-I../SoC/gd32vf103/Common/Include/Usb \ +-I../SoC/gd32vf103/Common/Source/Stubs + +# compile gcc flags +ASFLAGS = $(AS_DEFS) $(OPT) $(CORE_ARCH_ABI) $(OTHER_FLAGS) $(AS_INCLUDES) -Wall -fdata-sections -ffunction-sections + +CFLAGS = $(C_DEFS) $(C_INCLUDES) $(OPT) $(CORE_ARCH_ABI) $(OTHER_FLAGS) -Wall -fdata-sections -ffunction-sections + +# Generate dependency information +CFLAGS += -MMD -MP -MF"$(@:%.o=%.d)" + +# Set your GDB port using variable GDB_PORT +GDB_PORT ?= 3333 +## Makefile Variable GDBREMOTE +# You can change GDBREMOTE to other gdb remotes +## eg. if you have started openocd server with (bindto 0.0.0.0 defined in openocd.cfg) +## make sure your machine can connect to remote machine +## in remote machine(ipaddr 192.168.43.199, port 3333) which connect the hardware board, +## then you can change the GDBREMOTE to 192.168.43.199:3333 +## GDBREMOTE ?= 192.168.43.199:3333 +GDBREMOTE ?= | $(OPENOCD) --pipe -f $(OPENOCD_CFG) + +GDB_UPLOAD_ARGS ?= --batch +GDB_UPLOAD_CMDS += -ex "monitor halt" +GDB_UPLOAD_CMDS += -ex "monitor flash protect 0 0 last off" +GDB_UPLOAD_CMDS += -ex "load" +GDB_UPLOAD_CMDS += -ex "monitor resume" +GDB_UPLOAD_CMDS += -ex "quit" + +OPENOCD_PORT_ARGS = -c "gdb_port $(GDB_PORT)" + +OPENOCD_ARGS += -f $(OPENOCD_CFG) +GDB_CMDS += -ex "set remotetimeout 240" +GDB_CMDS += -ex "target extended-remote localhost:$(GDB_PORT)" + +####################################### +# LDFLAGS +####################################### +# link script +LDSCRIPT = gcc_gd32vf103_flashxip.ld + +# libraries +LIBS = -lm +LIBDIR = +LDFLAGS = $(CORE_ARCH_ABI) $(OTHER_FLAGS) -specs=nano.specs -specs=nosys.specs -T $(LDSCRIPT) $(LIBDIR) $(LIBS) -nostartfiles -Wl,-Map=$(BUILD_DIR)/$(TARGET).map,--cref -Wl,--gc-sections + +# default action: build all +all: $(BUILD_DIR)/$(TARGET).elf $(BUILD_DIR)/$(TARGET).dasm $(BUILD_DIR)/$(TARGET).hex $(BUILD_DIR)/$(TARGET).bin + +include liteos_m.mk + +####################################### +# build the application +####################################### +# list of objects +OBJECTS += $(addprefix $(BUILD_DIR)/,$(notdir $(C_SOURCES:.c=.o))) +vpath %.c $(sort $(dir $(C_SOURCES))) +# list of ASM program objects +OBJECTS += $(addprefix $(BUILD_DIR)/,$(notdir $(ASM_SOURCES:.S=.o))) +vpath %.s $(sort $(dir $(ASM_SOURCES))) + +$(BUILD_DIR)/%.o: %.c Makefile | $(BUILD_DIR) + $(CC) -c $(CFLAGS) -Wa,-a,-ad,-alms=$(BUILD_DIR)/$(notdir $(<:.c=.lst)) $< -o $@ + +$(BUILD_DIR)/%.o: %.s Makefile | $(BUILD_DIR) + $(AS) -c $(CFLAGS) $< -o $@ + +$(BUILD_DIR)/$(TARGET).elf: $(OBJECTS) Makefile $(LDSCRIPT) + $(CC) $(OBJECTS) $(LDFLAGS) -o $@ + $(SZ) $@ + +$(BUILD_DIR)/%.dasm: $(BUILD_DIR)/%.elf | $(BUILD_DIR) + $(DP) -D -S $< > $@ + +$(BUILD_DIR)/%.hex: $(BUILD_DIR)/%.elf | $(BUILD_DIR) + $(HEX) $< $@ + +$(BUILD_DIR)/%.bin: $(BUILD_DIR)/%.elf | $(BUILD_DIR) + $(BIN) $< $@ + +$(BUILD_DIR): + mkdir $@ + +####################################### +# clean up +####################################### +clean: + -rm -fR $(BUILD_DIR) + +####################################### +# upload & debug +####################################### +upload: $(BUILD_DIR)/$(TARGET).elf + @$(ECHO) "Download and run $<" + $(GDB) $< -ex "set remotetimeout 240" \ + -ex "target remote $(GDBREMOTE)" \ + $(GDB_UPLOAD_ARGS) $(GDB_UPLOAD_CMDS) + +debug: $(BUILD_DIR)/$(TARGET).elf + @$(ECHO) "Download and debug $<" + $(GDB) $< -ex "set remotetimeout 240" \ + -ex "target remote $(GDBREMOTE)" + +####################################### +# dependencies +####################################### +-include $(wildcard $(BUILD_DIR)/*.d) + +# *** EOF *** diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/gcc_gd32vf103_flashxip.ld b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/gcc_gd32vf103_flashxip.ld new file mode 100644 index 00000000..d4ca7932 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/gcc_gd32vf103_flashxip.ld @@ -0,0 +1,289 @@ +/* + * Copyright (c) 2019 Nuclei Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +/****************************************************************************** + * @file gcc_Device.ld + * @brief GNU Linker Script for gd32vf103 based device + * @version V1.0.0 + * @date 17. Dec 2019 + ******************************************************************************/ + +/*********** Use Configuration Wizard in Context Menu *************************/ + +OUTPUT_ARCH( "riscv" ) +/********************* Flash Configuration ************************************ + * Flash Configuration + * Flash Base Address <0x0-0xFFFFFFFF:8> + * Flash Size (in Bytes) <0x0-0xFFFFFFFF:8> + * + */ +__ROM_BASE = 0x08000000; +__ROM_SIZE = 0x00020000; + +/*--------------------- ILM RAM Configuration --------------------------- + * ILM RAM Configuration + * ILM RAM Base Address <0x0-0xFFFFFFFF:8> + * ILM RAM Size (in Bytes) <0x0-0xFFFFFFFF:8> + * + */ +__ILM_RAM_BASE = 0x80000000; +__ILM_RAM_SIZE = 0x00010000; + +/*--------------------- Embedded RAM Configuration --------------------------- + * RAM Configuration + * RAM Base Address <0x0-0xFFFFFFFF:8> + * RAM Size (in Bytes) <0x0-0xFFFFFFFF:8> + * +*/ +__RAM_BASE = 0x20000000; +__RAM_SIZE = 0x00005000; + +/********************* Stack / Heap Configuration **************************** + * Stack / Heap Configuration + * Stack Size (in Bytes) <0x0-0xFFFFFFFF:8> + * Heap Size (in Bytes) <0x0-0xFFFFFFFF:8> + * + */ +__STACK_SIZE = 0x00000800; +__HEAP_SIZE = 0x00000800; + +/**************************** end of configuration section ********************/ + +/* Define base address and length of flash and ram */ +MEMORY +{ + flash (rxai!w) : ORIGIN = __ROM_BASE, LENGTH = __ROM_SIZE + ram (wxa!ri) : ORIGIN = __RAM_BASE, LENGTH = __RAM_SIZE +} +/* Linker script to place sections and symbol values. Should be used together + * with other linker script that defines memory regions FLASH,ILM and RAM. + * It references following symbols, which must be defined in code: + * _Start : Entry of reset handler + * + * It defines following symbols, which code can use without definition: + * _ilm_lma + * _ilm + * __etext + * _etext + * etext + * _eilm + * __preinit_array_start + * __preinit_array_end + * __init_array_start + * __init_array_end + * __fini_array_start + * __fini_array_end + * _data_lma + * _edata + * edata + * __data_end__ + * __bss_start + * __fbss + * _end + * end + * __heap_end + * __StackLimit + * __StackTop + * __STACK_SIZE + */ +/* Define entry label of program */ +ENTRY(_start) +SECTIONS +{ + __STACK_SIZE = DEFINED(__STACK_SIZE) ? __STACK_SIZE : 2K; + + .init : + { + /* vector table locate at flash */ + *(.vtable) + KEEP (*(SORT_NONE(.init))) + } >flash AT>flash + + .ilalign : + { + . = ALIGN(4); + /* Create a section label as _ilm_lma which located at flash */ + PROVIDE( _ilm_lma = . ); + } >flash AT>flash + + .ialign : + { + /* Create a section label as _ilm which located at flash */ + PROVIDE( _ilm = . ); + } >flash AT>flash + + /* Code section located at flash */ + .text : + { + *(.text.unlikely .text.unlikely.*) + *(.text.startup .text.startup.*) + *(.text .text.*) + *(.gnu.linkonce.t.*) + } >flash AT>flash + + .rodata : ALIGN(4) + { + . = ALIGN(4); + *(.rdata) + *(.rodata .rodata.*) + /* section information for initial. */ + . = ALIGN(4); + __rt_init_start = .; + KEEP(*(SORT(.rti_fn*))) + __rt_init_end = .; + /* section information for finsh shell */ + . = ALIGN(4); + __fsymtab_start = .; + KEEP(*(FSymTab)) + __fsymtab_end = .; + . = ALIGN(4); + __vsymtab_start = .; + KEEP(*(VSymTab)) + __vsymtab_end = .; + *(.gnu.linkonce.r.*) + . = ALIGN(8); + *(.srodata.cst16) + *(.srodata.cst8) + *(.srodata.cst4) + *(.srodata.cst2) + *(.srodata .srodata.*) + } >flash AT>flash + + .fini : + { + KEEP (*(SORT_NONE(.fini))) + } >flash AT>flash + + . = ALIGN(4); + + PROVIDE (__etext = .); + PROVIDE (_etext = .); + PROVIDE (etext = .); + PROVIDE( _eilm = . ); + + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >flash AT>flash + + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT_BY_INIT_PRIORITY(.init_array.*) SORT_BY_INIT_PRIORITY(.ctors.*))) + KEEP (*(.init_array EXCLUDE_FILE (*crtbegin.o *crtbegin?.o *crtend.o *crtend?.o ) .ctors)) + PROVIDE_HIDDEN (__init_array_end = .); + } >flash AT>flash + + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT_BY_INIT_PRIORITY(.fini_array.*) SORT_BY_INIT_PRIORITY(.dtors.*))) + KEEP (*(.fini_array EXCLUDE_FILE (*crtbegin.o *crtbegin?.o *crtend.o *crtend?.o ) .dtors)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >flash AT>flash + + .ctors : + { + /* gcc uses crtbegin.o to find the start of + * the constructors, so we make sure it is + * first. Because this is a wildcard, it + * doesn't matter if the user does not + * actually link against crtbegin.o; the + * linker won't look for a file to match a + * wildcard. The wildcard also means that it + * doesn't matter which directory crtbegin.o + * is in. + */ + KEEP (*crtbegin.o(.ctors)) + KEEP (*crtbegin?.o(.ctors)) + /* We don't want to include the .ctor section from + * the crtend.o file until after the sorted ctors. + * The .ctor section from the crtend file contains the + * end of ctors marker and it must be last + */ + KEEP (*(EXCLUDE_FILE (*crtend.o *crtend?.o ) .ctors)) + KEEP (*(SORT(.ctors.*))) + KEEP (*(.ctors)) + } >flash AT>flash + + .dtors : + { + KEEP (*crtbegin.o(.dtors)) + KEEP (*crtbegin?.o(.dtors)) + KEEP (*(EXCLUDE_FILE (*crtend.o *crtend?.o ) .dtors)) + KEEP (*(SORT(.dtors.*))) + KEEP (*(.dtors)) + } >flash AT>flash + + .lalign : + { + . = ALIGN(4); + PROVIDE( _data_lma = . ); + } >flash AT>flash + + .dalign : + { + . = ALIGN(4); + PROVIDE( _data = . ); + } >ram AT>flash + + /* Define data section virtual address is ram and physical address is flash */ + .data : + { + *(.data .data.*) + *(.gnu.linkonce.d.*) + . = ALIGN(8); + PROVIDE( __global_pointer$ = . + 0x800 ); + *(.sdata .sdata.* .sdata*) + *(.gnu.linkonce.s.*) + } >ram AT>flash + + . = ALIGN(4); + PROVIDE( _edata = . ); + PROVIDE( edata = . ); + + PROVIDE( _fbss = . ); + PROVIDE( __bss_start = . ); + .bss : + { + *(.sbss*) + *(.gnu.linkonce.sb.*) + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + . = ALIGN(4); + } >ram AT>ram + + . = ALIGN(8); + PROVIDE( _end = . ); + PROVIDE( end = . ); + /* Define stack and head location at ram */ + .stack ORIGIN(ram) + LENGTH(ram) - __STACK_SIZE - __HEAP_SIZE : + { + PROVIDE( _heap_end = . ); +/* + PROVIDE( __los_heap_addr_start__ = . ); + . = __HEAP_SIZE; + PROVIDE( __los_heap_addr_end__ = . ); +*/ + . = __STACK_SIZE; + PROVIDE( _sp = . ); + } >ram AT>ram +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/liteos_m.mk b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/liteos_m.mk new file mode 100644 index 00000000..ea0580bb --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/liteos_m.mk @@ -0,0 +1,38 @@ +LITEOSTOPDIR := ../../../ +LITEOSTOPDIR := $(realpath $(LITEOSTOPDIR)) + +# Common +C_SOURCES += $(wildcard $(LITEOSTOPDIR)/kernel/src/*.c) \ + $(wildcard $(LITEOSTOPDIR)/kernel/src/mm/*.c) \ + $(wildcard $(LITEOSTOPDIR)/components/cpup/*.c) \ + $(wildcard $(LITEOSTOPDIR)/components/backtrace/*.c) \ + $(wildcard $(LITEOSTOPDIR)/components/bounds_checking_function/src/*.c) \ + $(wildcard $(LITEOSTOPDIR)/utils/*.c) + +C_INCLUDES += -I$(LITEOSTOPDIR)/utils \ + -I$(LITEOSTOPDIR)/kernel/include \ + -I$(LITEOSTOPDIR)/components/cpup \ + -I$(LITEOSTOPDIR)/components/backtrace \ + -I$(LITEOSTOPDIR)/components/bounds_checking_function/include + +# NMSIS related +C_INCLUDES += -I$(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc/nmsis/Core/Include \ + -I$(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc/nmsis/DSP/Include \ + -I$(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc/nmsis/NN/Include + +ASM_SOURCES += $(wildcard $(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc/*.s) + +ASMS_SOURCES += $(wildcard $(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc/*.S) + +C_SOURCES += $(wildcard $(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc/*.c) + +C_INCLUDES += -I. \ + -I$(LITEOSTOPDIR)/kernel/arch/include \ + -I$(LITEOSTOPDIR)/kernel/arch/risc-v/nuclei/gcc + +# list of ASM .S program objects +OBJECTS += $(addprefix $(BUILD_DIR)/,$(notdir $(ASMS_SOURCES:.S=.o))) +vpath %.S $(sort $(dir $(ASMS_SOURCES))) + +$(BUILD_DIR)/%.o: %.S Makefile | $(BUILD_DIR) + $(CC) -c $(CFLAGS) $< -o $@ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/openocd_gd32vf103.cfg b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/openocd_gd32vf103.cfg new file mode 100644 index 00000000..9247fca9 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/GCC/openocd_gd32vf103.cfg @@ -0,0 +1,53 @@ +adapter_khz 10000 +reset_config srst_only +adapter_nsrst_assert_width 100 + +interface ftdi +ftdi_vid_pid 0x0403 0x6010 + +## If ftdi_device_desc not specified, the device description is ignored during device selection. +## So if you want to specify a dedicated FTDI device, you can select following device description: +## "Dual RS232-HS" is for RVSTAR V1 on-board debugger +## "USB <-> JTAG-DEBUGGER" is for RVSTAR V2 on-board debugger +## Uncomment one which match your device description +# ftdi_device_desc "Dual RS232-HS" +# ftdi_device_desc "USB <-> JTAG-DEBUGGER" + +ftdi_layout_init 0x0008 0x001b +ftdi_layout_signal nSRST -oe 0x0020 -data 0x0020 +# These signals are used for cJTAG escape sequence on initialization only +ftdi_layout_signal TCK -data 0x0001 +ftdi_layout_signal TDI -data 0x0002 +ftdi_layout_signal TDO -input 0x0004 +ftdi_layout_signal TMS -data 0x0008 +ftdi_layout_signal JTAG_SEL -data 0x0100 -oe 0x0100 +transport select jtag + +set _CHIPNAME riscv +jtag newtap $_CHIPNAME cpu -irlen 5 -expected-id 0x1e200a6d + +# Work-area is a space in RAM used for flash programming +if { [info exists WORKAREASIZE] } { + set _WORKAREASIZE $WORKAREASIZE +} else { + set _WORKAREASIZE 0x5000 +} + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME riscv -chain-position $_TARGETNAME +$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0 + +set _FLASHNAME $_CHIPNAME.flash + +flash bank $_FLASHNAME gd32vf103 0x08000000 0 0 0 $_TARGETNAME + +# Expose Nuclei self-defined CSRS range +# See https://github.com/riscv/riscv-gnu-toolchain/issues/319#issuecomment-358397306 +# Then user can view the csr register value in gdb using: info reg csr775 for CSR MTVT(0x307) +riscv expose_csrs 770-800,835-850,1984-2032,2064-2070 + +riscv set_reset_timeout_sec 1 + +init + +halt diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/OS_CONFIG/target_config.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/OS_CONFIG/target_config.h new file mode 100644 index 00000000..75482ddc --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/OS_CONFIG/target_config.h @@ -0,0 +1,118 @@ +/* + * Copyright (c) 2013-2019 Huawei Technologies Co., Ltd. All rights reserved. + * Copyright (c) 2020-2021 Huawei Device Co., Ltd. All rights reserved. + * Copyright (c) 2021 Nuclei Limited. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, this list of + * conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright notice, this list + * of conditions and the following disclaimer in the documentation and/or other materials + * provided with the distribution. + * + * 3. Neither the name of the copyright holder nor the names of its contributors may be used + * to endorse or promote products derived from this software without specific prior written + * permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, + * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR + * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR + * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, + * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, + * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; + * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, + * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR + * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF + * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/**@defgroup los_config System configuration items + * @ingroup kernel + */ + +#ifndef _TARGET_CONFIG_H +#define _TARGET_CONFIG_H + +#ifdef __cplusplus +#if __cplusplus +extern "C" { +#endif /* __cplusplus */ +#endif /* __cplusplus */ + +/*============================================================================= + System clock module configuration +=============================================================================*/ +#define OS_SYS_CLOCK (108000000) +#define LOSCFG_BASE_CORE_TICK_PER_SECOND (1000UL) +#define LOSCFG_BASE_CORE_TICK_HW_TIME 0 +/*============================================================================= + Hardware interrupt module configuration +=============================================================================*/ +#define LOSCFG_PLATFORM_HWI 1 +#define LOSCFG_USE_SYSTEM_DEFINED_INTERRUPT 0 +#define LOSCFG_PLATFORM_HWI_LIMIT 32 +/*============================================================================= + Task module configuration +=============================================================================*/ +#define LOSCFG_BASE_CORE_TSK_LIMIT 12 +#define LOSCFG_BASE_CORE_TSK_IDLE_STACK_SIZE (0x280U) +#define LOSCFG_BASE_CORE_TSK_DEFAULT_STACK_SIZE (0x200U) +#define LOSCFG_BASE_CORE_TSK_MIN_STACK_SIZE (0x130U) +#define LOSCFG_BASE_CORE_TIMESLICE 1 +#define LOSCFG_BASE_CORE_TIMESLICE_TIMEOUT 10 +/*============================================================================= + Semaphore module configuration +=============================================================================*/ +#define LOSCFG_BASE_IPC_SEM 1 +#define LOSCFG_BASE_IPC_SEM_LIMIT 48 +/*============================================================================= + Mutex module configuration +=============================================================================*/ +#define LOSCFG_BASE_IPC_MUX 1 +#define LOSCFG_BASE_IPC_MUX_LIMIT 10 +/*============================================================================= + Queue module configuration +=============================================================================*/ +#define LOSCFG_BASE_IPC_QUEUE 1 +#define LOSCFG_BASE_IPC_QUEUE_LIMIT 6 +/*============================================================================= + Software timer module configuration +=============================================================================*/ +#define LOSCFG_BASE_CORE_SWTMR 1 +#define LOSCFG_BASE_CORE_SWTMR_ALIGN 1 +#define LOSCFG_BASE_CORE_SWTMR_LIMIT 6 +/*============================================================================= + Memory module configuration +=============================================================================*/ +#define LOSCFG_SYS_HEAP_SIZE 0x03800UL +#define OS_SYS_MEM_SIZE 0x00000800 +#define LOSCFG_BASE_MEM_NODE_INTEGRITY_CHECK 0 +#define LOSCFG_BASE_MEM_NODE_SIZE_CHECK 1 +#define LOSCFG_MEM_MUL_POOL 0 +#define OS_SYS_MEM_NUM 20 +#define LOSCFG_KERNEL_MEM_SLAB 0 +/*============================================================================= + Exception module configuration +=============================================================================*/ +#define LOSCFG_PLATFORM_EXC 0 +/* ============================================================================= + printf module configuration +============================================================================= */ +#define LOSCFG_KERNEL_PRINTF 1 +/* ============================================================================= + enable backtrace +============================================================================= */ +#define LOSCFG_BACKTRACE_TYPE 0 + +#ifdef __cplusplus +#if __cplusplus +} +#endif /* __cplusplus */ +#endif /* __cplusplus */ + + +#endif /* _TARGET_CONFIG_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/README.md b/targets/riscv_nuclei_gd32vf103_soc_gcc/README.md new file mode 100644 index 00000000..3b12ee86 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/README.md @@ -0,0 +1,203 @@ +# RV-STAR开发板LiteOS使用说明 + +## RV-STAR开发板简介 + +RV-STAR是一款基于GD32VF103 MCU的RISC-V评估开发板，提供了板载调试器、Reset和Wakeup用户按键、RGB LED、USB OTG，以及EXMC、Arduino和PMOD扩展接口等资源。 + +开发板资料链接： + +- [RV-STAR开发板电路原理图](https://www.rvmcu.com/quickstart-doc-u-pdf-id-235.html) +- [RV-STAR开发板用户手册（Segger Embedded Studio IDE版）](https://www.rvmcu.com/quickstart-doc-u-pdf-id-236.html) +- [RV-STAR开发板用户手册（Nuclei Studio IDE版）](https://www.rvmcu.com/quickstart-doc-u-pdf-id-531.html) +- [RV-STAR板载GD32VF103芯片资料](https://www.rvmcu.com/quickstart-doc-u-gd32vf103.html) +- [芯来RISC-V Bumblebee内核指令集手册](https://www.rvmcu.com/quickstart-doc-u-pdf-id-8.html) + +## 文件结构 + +``` +├── components # 可选组件 +│ ├── cppsupport # C++支持 +│ └── cpup # CPUP功能 +├── kal # 内核抽象层 +│ └── posix # posix标准接口支持 +├── kernel # 内核最小功能集支持 +│ ├── arch # 内核指令架构层代码 +│ │ ├── risc-v # risc-v架构的代码 +│ │ │ └── nuclei # nuclei内核相关代码 +│ │ │ └── gcc # gcc编译器相关代码 +│ │ │ ├── nmsis # nmsis内核标准 +│ │ └── include # 对外接口存放目录 +│ │ ├── los_arch_atomic.h # 定义通用arch的原子操作 +│ │ ├── los_arch_context.h # 定义通用arch的上下文切换 +│ │ ├── los_arch.h # 定义通用arch初始化 +│ │ └── los_arch_interrupt.h # 定义通用arch中断 +│ ├── include # 对外接口存放目录 +│   │   ├── los_config.h # 功能开关和配置参数 +│   │   ├── los_event.h # 事件 +│   │   ├── los_liteos.h # liteos最小功能集对外提供的头文件 +│   │   ├── los_memory.h # 堆内存管理 +│   │   ├── los_mutex.h # 互斥锁 +│   │   ├── los_queue.h # 队列 +│   │   ├── los_scheduler.h # 调度算法 +│   │   ├── los_sem.h # 信号量 +│   │   ├── los_task.h # 任务 +│   │   └── los_timer.h # 定时器 +│ └── src # 内核最小功能集源码 +├── targets # 板级工程目录 +│ ├── riscv_nuclei_gd32vf103_soc_gcc # RV-STAR开发板相关代码 +│ ├── GCC # 编译相关 +│ ├── OS_CONFIG # 开发板配置功能开关和配置参数 +│ ├── SoC # gd32vf103 SOC相关代码 +│ └── Src # application相关代码 +├── utils # 通用公共目录 + ├── include + │   ├── los_compiler.h # 编译工具配置，类型定义 + │   ├── los_debug.h # debug，printf相关 + │   ├── los_error.h # 错误定义 + │   └── los_list.h + └── src +``` + +## 使用说明 + +软件需求：linux环境 + +硬件需求：RV-STAR开发板 + +[环境配置](#sectionb1) + +[编译源码](#sectionb2) + +[下载调试、运行](#sectionb3) + +本示例将新建并运行两个任务，PA0按键为外部中断，按下后可以查看任务列表信息。 + +### 环境配置 + +- **工具链配置** + +请先确认您使用的是centos系统或Ububntu 64bit。 + +1. 新建一个`Nuclei` 文件夹，比如`~/Software/Nuclei` +2. 参考下图，从[Nuclei Download Center](https://nucleisys.com/download.php)下载工具链和OpenOCD。 + - CentOS或Ubuntu系统请点击图中红框1下载RISC-V GNU工具链 + - 点击图中蓝框2-1下载64bit的OpenOCD + - **确保Make工具版本不低于3.82**: ubuntu系统使用`sudo apt-get install make`指令安装`make`工具, CentOS系统使用`sudo yum install make`指令安装。 + +图1 Linux环境要下载的Nuclei Tools + +![Nuclei Tools need to be downloaded for Linux](doc/image/nuclei_tools_download_linux.png) + + + +3. 在之前新建的`Nuclei`文件夹中新建`gcc`文件夹和`openocd`文件夹。 + - 解压缩之前下载的**gnu工具链**到任意文件夹中，复制其中`bin`文件件所在层级的所有内容到`gcc`文件夹中。 + - 同样解压缩之前下载的**OpenOCD**到任意文件夹中，复制其中`bin`文件件所在层级的所有内容到`openocd`文件夹中。 + +> 注意： +> +> ​ 请务必下载并解压缩Linux版本的工具，不要下载windows版本工具。 + +- **驱动配置** + +驱动配置步骤如下： + +1. 连接开发板到Linux中，确保USB被Linux识别出来。 + +2. 在控制台中使用lsusb指令查看信息，参考的打印信息如下： + + ``` + Bus 001 Device 010: ID 0403:6010 Future Technology Devices International, Ltd FT2232xxxx + ``` + +3. 将github（https://github.com/riscv-mcu/ses_nuclei_sdk_projects/blob/master/misc/99-openocd.rules）上misc文件夹内99-openocd.rules文件复制到当前路径下，控制台中输入sudo cp 99-openocd.rules /etc/udev/rules.d/99-openocd.rules指令复制文件到指定路径下。 + +4. 断开调试器再重新连接到Linux系统中。 + +5. 使用ls /dev/ttyUSB*命令查看ttyUSB信息，参考输出如下： + + ``` + /dev/ttyUSB0 /dev/ttyUSB1 + ``` + +6. 使用ls -l /dev/ttyUSB1命令查看分组信息，参考输出如下: + + ``` + crw-rw-r-- 1 root plugdev 188, 1 Nov 28 12:53 /dev/ttyUSB1 + ``` + + 可以看到ttyUSB1已经加入plugdev组，接下来我们要将自己添加到plugdev组。使用whoami命令查看当前用户名，我们将其记录为\< your_user_name >。 + +7. 使用sudo usermod -a -G plugdev \命令将自己添加进plugdev组。 + +8. 再次确认当前用户名已属于plugdev组，使用groups命令，可以看到打印信息中有plugdev即成功将当前用户添加至plugdev组。 + +### 编译源码 + +编译前请在当前控制台中配置`NUCLEI_TOOL_ROOT`路径，假设`Nuclei`文件夹所在路径为`/home/Nuclei`，输入`export NUCLEI_TOOL_ROOT=/home/Nuclei` 。或者使用时make选项增加`NUCLEI_TOOL_ROOT=/home/Nuclei`。 + +配置路径后打开至代码根目录下的/target/riscv_nuclei_gd32vf103_soc_gcc/GCC位置，输入如下指令开始编译： + +``` +make all +``` + +编译结束后部分参考输出如下： + +``` + text data bss dec hex filename + 24330 112 16768 41210 a0fa build/Nuclei-rvstar-gd32vf103-soc.elf +``` + +若编译前想清理工程，请使用如下指令： + +``` +make clean +``` + +### 下载调试、运行 + +调试或运行前请先连接RV-STAR开发板，确保已按照[环境配置](#sectionb1)中驱动配置部分配置完成。 + +同样配置好`NUCLEI_TOOL_ROOT`路径并打开至代码根目录下的/target/riscv_nuclei_gd32vf103_soc_gcc/GCC位置，输入如下指令进入GDB调试： + +``` +make debug +``` + +等待到进入GDB调试界面时，输入`load`指令下载编译好的elf文件，就可以开始调试。 + +若想直接运行，请在调试时所在位置输入如下指令： + +``` +make upload +``` + +运行时可以查看串口打印内容，使用串口查看工具，这里以`minicom`为例，若未安装此工具可自行安装或使用其他串口查看工具。打开控制台，输入`minicom -D /dev/ttyUSB1 -b 115200`指令打开串口查看工具。 + +运行时参考输出如下： + +``` +Nuclei SDK Build Time: Mar 30 2021, 18:26:53 +Download Mode: FLASHXIP +CPU Frequency 108540000 Hz +entering kernel init... +TaskSampleEntry1 running... +TaskSampleEntry1 running... +TaskSampleEntry1 running... +TaskSampleEntry1 running... +TaskSampleEntry2 running... +TaskSampleEntry1 running... +TaskSampleEntry1 running... +EXTI0_IRQHandler running... +ID Pri Status name +-- --- --------- ---- +0 0 QueuePend Swt_Task +1 31 Running IdleCore000 +2 6 Delay TaskSampleEntry1 +3 7 Delay TaskSampleEntry2 +TaskSampleEntry1 running... +TaskSampleEntry1 running... +TaskSampleEntry1 running... +TaskSampleEntry2 running... +``` diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/gd32vf103v_rvstar.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/gd32vf103v_rvstar.h new file mode 100644 index 00000000..60f1b0d5 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/gd32vf103v_rvstar.h @@ -0,0 +1,134 @@ +/*! + \file gd32vf103c_start.h + \brief definitions for GD32VF103C_START's leds, keys and COM ports hardware resources + + \version 2019-06-05, V1.0.0, demo for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103C_RVSTART_H +#define GD32VF103C_RVSTART_H + +#ifdef __cplusplus + extern "C" { +#endif + +#include "nuclei_sdk_soc.h" + +/* exported types */ +typedef enum +{ + LED1 = 0, + LED2 = 1, + LED3 = 2, + LED_1 = 0, + LED_2 = 1, + LED_3 = 2 +}led_typedef_enum; + +typedef enum +{ + KEY_WAKEUP = 0, +}key_typedef_enum; + +typedef enum +{ + KEY_MODE_GPIO = 0, + KEY_MODE_EXTI = 1 +}keymode_typedef_enum; + + +/* rvstar board low layer led */ +#define LEDn 3U + +#define LEDG_PIN GPIO_PIN_1 +#define LEDG_GPIO_PORT GPIOA +#define LEDG_GPIO_CLK RCU_GPIOA + +#define LEDB_PIN GPIO_PIN_3 +#define LEDB_GPIO_PORT GPIOA +#define LEDB_GPIO_CLK RCU_GPIOA + +#define LEDR_PIN GPIO_PIN_2 +#define LEDR_GPIO_PORT GPIOA +#define LEDR_GPIO_CLK RCU_GPIOA + +/* rvstar board UART com port */ +#define GD32_COM0 UART4 +#define GD32_COM_CLK RCU_UART4 +#define GD32_COM_TX_PIN GPIO_PIN_12 +#define GD32_COM_RX_PIN GPIO_PIN_2 +#define GD32_COM_TX_GPIO_PORT GPIOC +#define GD32_COM_RX_GPIO_PORT GPIOD +#define GD32_COM_TX_GPIO_CLK RCU_GPIOC +#define GD32_COM_RX_GPIO_CLK RCU_GPIOD + +/* rvstar board low layer button */ +#define KEYn (1U) + +/* wakeup push-button */ +#define WAKEUP_KEY_PIN GPIO_PIN_0 +#define WAKEUP_KEY_GPIO_PORT GPIOA +#define WAKEUP_KEY_GPIO_CLK RCU_GPIOA +#define WAKEUP_KEY_EXTI_LINE EXTI_0 +#define WAKEUP_KEY_EXTI_PORT_SOURCE GPIO_PORT_SOURCE_GPIOA +#define WAKEUP_KEY_EXTI_PIN_SOURCE GPIO_PIN_SOURCE_0 +#define WAKEUP_KEY_EXTI_IRQn EXTI0_IRQn + +/* function declarations */ +/* configure led GPIO */ +void gd_led_init(led_typedef_enum lednum); +/* turn on selected led */ +void gd_led_on(led_typedef_enum lednum); +/* turn off selected led */ +void gd_led_off(led_typedef_enum lednum); +/* toggle the selected led */ +void gd_led_toggle(led_typedef_enum lednum); +/* configure key */ +void gd_key_init(key_typedef_enum keynum, keymode_typedef_enum keymode); +/* return the selected key state */ +uint8_t gd_key_state_get(key_typedef_enum keynum); +/* configure COM port */ +void gd_com_init(uint32_t usart_periph); + +/* Defines for LED functio/* Defines for LED / Key functions to new / general API */ +#define gd_rvstar_led_init gd_led_init +#define gd_rvstar_led_on gd_led_on +#define gd_rvstar_led_off gd_led_off +#define gd_rvstar_led_toggle gd_led_toggle + +#define gd_rvstar_key_init gd_key_init +#define gd_rvstar_key_state_get gd_key_state_get + +#ifdef __cplusplus +} +#endif + +#endif /* GD32VF103V_RVSTART_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/nuclei_sdk_hal.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/nuclei_sdk_hal.h new file mode 100644 index 00000000..afa3fd70 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Include/nuclei_sdk_hal.h @@ -0,0 +1,20 @@ +// See LICENSE for license details. +#ifndef _NUCLEI_SDK_HAL_H +#define _NUCLEI_SDK_HAL_H + +#ifdef __cplusplus + extern "C" { +#endif + +#include "gd32vf103v_rvstar.h" + +#define SOC_DEBUG_UART GD32_COM0 + +#ifndef NUCLEI_BANNER +#define NUCLEI_BANNER 1 +#endif + +#ifdef __cplusplus +} +#endif +#endif diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Source/gd32vf103v_rvstar.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Source/gd32vf103v_rvstar.c new file mode 100644 index 00000000..023d97f6 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Board/gd32vf103v_rvstar/Source/gd32vf103v_rvstar.c @@ -0,0 +1,191 @@ +/*! + * \file gd32vf103c_start.c + * \brief firmware functions to manage leds, keys, COM ports + * + * \version 2020-02-05, V1.0.0, rvstar board functions for GD32VF103 + */ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103v_rvstar.h" + +/* private variables */ +static const uint32_t GPIO_PORT[LEDn] = {LEDG_GPIO_PORT,LEDB_GPIO_PORT,LEDR_GPIO_PORT}; + +static const uint32_t GPIO_PIN[LEDn] = {LEDG_PIN,LEDB_PIN,LEDR_PIN}; + +static const rcu_periph_enum GPIO_CLK[LEDn] = {LEDG_GPIO_CLK,LEDB_GPIO_CLK,LEDR_GPIO_CLK}; + +static const uint32_t KEY_PORT[KEYn] = {WAKEUP_KEY_GPIO_PORT}; + +static const uint32_t KEY_PIN[KEYn] = {WAKEUP_KEY_PIN}; + +static const rcu_periph_enum KEY_CLK[KEYn] = {WAKEUP_KEY_GPIO_CLK}; + +static const exti_line_enum KEY_EXTI_LINE[KEYn] = {WAKEUP_KEY_EXTI_LINE}; + +static const uint8_t KEY_PORT_SOURCE[KEYn] = {WAKEUP_KEY_EXTI_PORT_SOURCE}; + +static const uint8_t KEY_PIN_SOURCE[KEYn] = {WAKEUP_KEY_EXTI_PIN_SOURCE}; + +static const uint8_t KEY_IRQn[KEYn] = {WAKEUP_KEY_EXTI_IRQn}; + +/* eval board low layer private functions */ +/*! + * \brief configure led GPIO + * \param[in] lednum: specify the led to be configured + * \arg LED1 + * \param[out] none + * \retval none + */ +void gd_led_init(led_typedef_enum lednum) +{ + /* enable the led clock */ + rcu_periph_clock_enable(GPIO_CLK[lednum]); + /* configure led GPIO port */ + gpio_init(GPIO_PORT[lednum], GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, GPIO_PIN[lednum]); + GPIO_BOP(GPIO_PORT[lednum]) = GPIO_PIN[lednum]; +} + +/*! + * \brief turn on selected led + * \param[in] lednum: specify the led to be turned on + * \arg LED1 + * \param[out] none + * \retval none + */ +void gd_led_on(led_typedef_enum lednum) +{ + GPIO_BC(GPIO_PORT[lednum]) = GPIO_PIN[lednum]; +} + +/*! + * \brief turn off selected led + * \param[in] lednum: specify the led to be turned off + * \arg LED1 + * \param[out] none + * \retval none + */ +void gd_led_off(led_typedef_enum lednum) +{ + GPIO_BOP(GPIO_PORT[lednum]) = GPIO_PIN[lednum]; +} + +/*! + * \brief toggle selected led + * \param[in] lednum: specify the led to be toggled + * \arg LED1 + * \param[out] none + * \retval none + */ +void gd_led_toggle(led_typedef_enum lednum) +{ + gpio_bit_write(GPIO_PORT[lednum], GPIO_PIN[lednum], + (bit_status)(1-gpio_input_bit_get(GPIO_PORT[lednum], GPIO_PIN[lednum]))); +} + +/*! + * \brief configure key + * \param[in] keynum: specify the key to be configured + * \arg KEY_WAKEUP: wakeup key + * \param[in] keymode: specify button mode + * \arg KEY_MODE_GPIO: key will be used as simple IO + * \arg KEY_MODE_EXTI: key will be connected to EXTI line with interrupt + * \param[out] none + * \retval none + */ +void gd_key_init(key_typedef_enum keynum, keymode_typedef_enum keymode) +{ + /* enable the key clock */ + rcu_periph_clock_enable(KEY_CLK[keynum]); + rcu_periph_clock_enable(RCU_AF); + + /* configure button pin as input */ + gpio_init(KEY_PORT[keynum], GPIO_MODE_IN_FLOATING, GPIO_OSPEED_50MHZ, KEY_PIN[keynum]); + + if (keymode == KEY_MODE_EXTI) { + /* enable and set key EXTI interrupt to the lowest priority */ + ECLIC_EnableIRQ(KEY_IRQn[keynum]); + ECLIC_SetLevelIRQ(KEY_IRQn[keynum],1); + ECLIC_SetPriorityIRQ(KEY_IRQn[keynum],1); + + /* connect key EXTI line to key GPIO pin */ + gpio_exti_source_select(KEY_PORT_SOURCE[keynum], KEY_PIN_SOURCE[keynum]); + + /* configure key EXTI line */ + exti_init(KEY_EXTI_LINE[keynum], EXTI_INTERRUPT, EXTI_TRIG_FALLING); + exti_interrupt_flag_clear(KEY_EXTI_LINE[keynum]); + } +} + +/*! + * \brief return the selected key state + * \param[in] keynum: specify the key to be checked + * \arg KEY_WAKEUP: wakeup key + * \param[out] none + * \retval the key's GPIO pin value + */ +uint8_t gd_key_state_get(key_typedef_enum keynum) +{ + return gpio_input_bit_get(KEY_PORT[keynum], KEY_PIN[keynum]); +} + +/*! + * \brief configure COM port + * \param[in] com: COM on the board + * \arg GD32_COM0: COM0 on the board + * \param[out] none + * \retval none + */ +void gd_com_init(uint32_t usart_periph) +{ + /* enable GPIO TX and RX clock */ + rcu_periph_clock_enable(GD32_COM_TX_GPIO_CLK); + rcu_periph_clock_enable(GD32_COM_RX_GPIO_CLK); + + /* enable USART clock */ + rcu_periph_clock_enable(GD32_COM_CLK); + + /* connect port to USARTx_Tx */ + gpio_init(GD32_COM_TX_GPIO_PORT, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GD32_COM_TX_PIN); + + /* connect port to USARTx_Rx */ + gpio_init(GD32_COM_RX_GPIO_PORT, GPIO_MODE_IN_FLOATING, GPIO_OSPEED_50MHZ, GD32_COM_RX_PIN); + + /* USART configure */ + usart_deinit(usart_periph); + usart_baudrate_set(usart_periph, 115200U); + usart_word_length_set(usart_periph, USART_WL_8BIT); + usart_stop_bit_set(usart_periph, USART_STB_1BIT); + usart_parity_config(usart_periph, USART_PM_NONE); + usart_hardware_flow_rts_config(usart_periph, USART_RTS_DISABLE); + usart_hardware_flow_cts_config(usart_periph, USART_CTS_DISABLE); + usart_receive_config(usart_periph, USART_RECEIVE_ENABLE); + usart_transmit_config(usart_periph, USART_TRANSMIT_ENABLE); + usart_enable(usart_periph); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_core.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_core.h new file mode 100644 index 00000000..b70448b4 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_core.h @@ -0,0 +1,117 @@ +/*! + \file drv_usb_core.h + \brief USB core low level driver header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USB_CORE_H +#define __DRV_USB_CORE_H + +#include "drv_usb_regs.h" +#include "usb_ch9_std.h" + +#define USB_FS_EP0_MAX_LEN 64U /* maximum packet size of EndPoint0 */ + +#define HC_MAX_PACKET_COUNT 140U /* maximum packet count */ + +#define EP_ID(x) ((uint8_t)((x) & 0x7FU)) /* endpoint number */ +#define EP_DIR(x) ((uint8_t)((x) >> 7)) /* endpoint direction */ + +enum _usb_eptype { + USB_EPTYPE_CTRL = 0U, /*!< control endpoint type */ + USB_EPTYPE_ISOC = 1U, /*!< isochronous endpoint type */ + USB_EPTYPE_BULK = 2U, /*!< bulk endpoint type */ + USB_EPTYPE_INTR = 3U, /*!< interrupt endpoint type */ + USB_EPTYPE_MASK = 3U, /*!< endpoint type mask */ +}; + +typedef enum +{ + USB_OTG_OK = 0, /*!< USB OTG status OK*/ + USB_OTG_FAIL /*!< USB OTG status fail*/ +} usb_otg_status; + +typedef enum +{ + USB_OK = 0, /*!< USB status OK*/ + USB_FAIL /*!< USB status fail*/ +} usb_status; + +typedef enum +{ + USB_USE_FIFO, /*!< USB use FIFO transfer mode */ + USB_USE_DMA /*!< USB use DMA transfer mode */ +} usb_transfer_mode; + +typedef struct +{ + uint8_t core_enum; /*!< USB core type */ + uint8_t core_speed; /*!< USB core speed */ + uint8_t num_pipe; /*!< USB host channel numbers */ + uint8_t num_ep; /*!< USB device endpoint numbers */ + uint8_t transfer_mode; /*!< USB transfer mode */ + uint8_t phy_itf; /*!< USB core PHY interface */ + uint8_t sof_enable; /*!< USB SOF output */ + uint8_t low_power; /*!< USB low power */ +} usb_core_basic; + +/* function declarations */ + +/* config core capabilities */ +usb_status usb_basic_init (usb_core_basic *usb_basic, + usb_core_regs *usb_regs, + usb_core_enum usb_core); + +/*initializes the USB controller registers and prepares the core device mode or host mode operation*/ +usb_status usb_core_init (usb_core_basic usb_basic, usb_core_regs *usb_regs); + +/* read a packet from the Rx FIFO associated with the endpoint */ +void *usb_rxfifo_read (usb_core_regs *core_regs, uint8_t *dest_buf, uint16_t byte_count); + +/* write a packet into the Tx FIFO associated with the endpoint */ +usb_status usb_txfifo_write (usb_core_regs *usb_regs, + uint8_t *src_buf, + uint8_t fifo_num, + uint16_t byte_count); + +/* flush a Tx FIFO or all Tx FIFOs */ +usb_status usb_txfifo_flush (usb_core_regs *usb_regs, uint8_t fifo_num); + +/* flush the entire Rx FIFO */ +usb_status usb_rxfifo_flush (usb_core_regs *usb_regs); + +/* get the global interrupts */ +static inline uint32_t usb_coreintr_get(usb_core_regs *usb_regs) +{ + return usb_regs->gr->GINTEN & usb_regs->gr->GINTF; +} + +#endif /* __DRV_USB_CORE_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_dev.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_dev.h new file mode 100644 index 00000000..9750dbea --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_dev.h @@ -0,0 +1,217 @@ +/*! + \file drv_usb_dev.h + \brief USB device low level driver header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USB_DEV_H +#define __DRV_USB_DEV_H + +#include "drv_usb_core.h" + +enum usb_ctl_status { + USB_CTL_IDLE = 0U, /*!< USB control transfer idle state */ + USB_CTL_DATA_IN, /*!< USB control transfer data in state */ + USB_CTL_LAST_DATA_IN, /*!< USB control transfer last data in state */ + USB_CTL_DATA_OUT, /*!< USB control transfer data out state */ + USB_CTL_LAST_DATA_OUT, /*!< USB control transfer last data out state */ + USB_CTL_STATUS_IN, /*!< USB control transfer status in state*/ + USB_CTL_STATUS_OUT /*!< USB control transfer status out state */ +}; + +#define EP_IN(x) ((uint8_t)(0x80U | (x))) /*!< device IN endpoint */ +#define EP_OUT(x) ((uint8_t)(x)) /*!< device OUT endpoint */ + +/* USB descriptor */ +typedef struct _usb_desc { + uint8_t *dev_desc; /*!< device descriptor */ + uint8_t *config_desc; /*!< config descriptor */ + uint8_t *bos_desc; /*!< BOS descriptor */ + + void* const *strings; /*!< string descriptor */ +} usb_desc; + +/* USB power management */ +typedef struct _usb_pm { + uint8_t power_mode; /*!< power mode */ + uint8_t power_low; /*!< power low */ + uint8_t dev_remote_wakeup; /*!< remote wakeup */ + uint8_t remote_wakeup_on; /*!< remote wakeup on */ +} usb_pm; + +/* USB control information */ +typedef struct _usb_control { + usb_req req; /*!< USB standard device request */ + + uint8_t ctl_state; /*!< USB control transfer state */ + uint8_t ctl_zlp; /*!< zero lenth package */ +} usb_control; + +typedef struct +{ + struct { + uint8_t num: 4; /*!< the endpoint number.it can be from 0 to 6 */ + uint8_t pad: 3; /*!< padding between number and direction */ + uint8_t dir: 1; /*!< the endpoint direction */ + } ep_addr; + + uint8_t ep_type; /*!< USB endpoint type */ + uint8_t ep_stall; /*!< USB endpoint stall status */ + + uint8_t frame_num; /*!< number of frame */ + uint16_t max_len; /*!< Maximum packet lenth */ + + /* transaction level variables */ + uint8_t *xfer_buf; /*!< transmit buffer */ + uint32_t xfer_len; /*!< transmit buffer length */ + uint32_t xfer_count; /*!< transmit buffer count */ + + uint32_t remain_len; /*!< remain packet lenth */ + + uint32_t dma_addr; /*!< DMA address */ +} usb_transc; + +typedef struct _usb_core_driver usb_dev; + +typedef struct _usb_class_core +{ + uint8_t command; /*!< device class request command */ + uint8_t alter_set; /*!< alternative set */ + + uint8_t (*init) (usb_dev *udev, uint8_t config_index); /*!< initialize handler */ + uint8_t (*deinit) (usb_dev *udev, uint8_t config_index); /*!< de-initialize handler */ + + uint8_t (*req_proc) (usb_dev *udev, usb_req *req); /*!< device request handler */ + + uint8_t (*data_in) (usb_dev *udev, uint8_t ep_num); /*!< device data in handler */ + uint8_t (*data_out) (usb_dev *udev, uint8_t ep_num); /*!< device data out handler */ + + uint8_t (*SOF) (usb_dev *udev); /*!< Start of frame handler */ + + uint8_t (*incomplete_isoc_in) (usb_dev *udev); /*!< Incomplete synchronization IN transfer handler */ + uint8_t (*incomplete_isoc_out) (usb_dev *udev); /*!< Incomplete synchronization OUT transfer handler */ +} usb_class_core; + +typedef struct _usb_perp_dev +{ + uint8_t config; /*!< configuration */ + uint8_t dev_addr; /*!< device address */ + + __IO uint8_t cur_status; /*!< current status */ + __IO uint8_t backup_status; /*!< backup status */ + + usb_transc transc_in[USBFS_MAX_TX_FIFOS]; /*!< endpoint IN transaction */ + usb_transc transc_out[USBFS_MAX_TX_FIFOS]; /*!< endpoint OUT transaction */ + + usb_pm pm; /*!< power management */ + usb_desc desc; /*!< USB descriptors */ + usb_control control; /*!< USB control information */ + + usb_class_core *class_core; /*!< class driver */ +} usb_perp_dev; + +typedef struct _usb_core_driver +{ + usb_core_basic bp; /*!< USB basic parameters */ + usb_core_regs regs; /*!< USB registers */ + usb_perp_dev dev; /*!< USB peripheral device */ +} usb_core_driver; + +/* function declarations */ + +/* initialize USB core registers for device mode */ +usb_status usb_devcore_init (usb_core_driver *udev); + +/* enable the USB device mode interrupts */ +usb_status usb_devint_enable (usb_core_driver *udev); + +/* active the usb transaction */ +usb_status usb_transc_active (usb_core_driver *udev, usb_transc *transc); + +/* deactive the usb transaction */ +usb_status usb_transc_deactivate (usb_core_driver *udev, usb_transc *transc); + +/* configure usb transaction to start IN transfer */ +usb_status usb_transc_inxfer (usb_core_driver *udev, usb_transc *transc); + +/* configure usb transaction to start OUT transfer */ +usb_status usb_transc_outxfer (usb_core_driver *udev, usb_transc *transc); + +/* set the usb transaction STALL status */ +usb_status usb_transc_stall (usb_core_driver *udev, usb_transc *transc); + +/* clear the usb transaction STALL status */ +usb_status usb_transc_clrstall (usb_core_driver *udev, usb_transc *transc); + +/* read device all OUT endpoint interrupt register */ +uint32_t usb_oepintnum_read (usb_core_driver *udev); + +/* read device OUT endpoint interrupt flag register */ +uint32_t usb_oepintr_read (usb_core_driver *udev, uint8_t ep_num); + +/* read device all IN endpoint interrupt register */ +uint32_t usb_iepintnum_read (usb_core_driver *udev); + +/* read device IN endpoint interrupt flag register */ +uint32_t usb_iepintr_read (usb_core_driver *udev, uint8_t ep_num); + +/* config the USB device to be disconnected */ +void usb_dev_disconnect (usb_core_driver *udev); + +/* config the USB device to be connected */ +void usb_dev_connect (usb_core_driver *udev); + +/* set the USB device address */ +void usb_devaddr_set (usb_core_driver *pudev, uint8_t dev_addr); + +/* configures OUT endpoint 0 to receive SETUP packets */ +void usb_ctlep_startout (usb_core_driver *udev); + +/* active remote wakeup signalling */ +void usb_rwkup_active (usb_core_driver *udev); + +/* reset remote wakeup signalling */ +void usb_rwkup_reset (usb_core_driver *udev); + +/* set remote wakeup signalling */ +void usb_rwkup_set (usb_core_driver *udev); + +/* active USB core clock */ +void usb_clock_active (usb_core_driver *udev); + +/* usb device suspend */ +void usb_dev_suspend (usb_core_driver *udev); + +/* stop the device and clean up fifos */ +void usb_dev_stop (usb_core_driver *udev); + +#endif /* __DRV_USB_DEV_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_host.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_host.h new file mode 100644 index 00000000..443800bd --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_host.h @@ -0,0 +1,175 @@ +/*! + \file drv_usb_host.h + \brief USB host mode low level driver header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USB_HOST_H +#define __DRV_USB_HOST_H + +#include "drv_usb_regs.h" +#include "usb_ch9_std.h" +#include "drv_usb_core.h" + +typedef enum _usb_pipe_status +{ + PIPE_IDLE = 0U, + PIPE_XF, + PIPE_HALTED, + PIPE_NAK, + PIPE_NYET, + PIPE_STALL, + PIPE_TRACERR, + PIPE_BBERR, + PIPE_REQOVR, + PIPE_DTGERR, +} usb_pipe_staus; + +typedef enum _usb_pipe_mode +{ + PIPE_PERIOD = 0U, + PIPE_NON_PERIOD = 1U +} usb_pipe_mode; + +typedef enum _usb_urb_state +{ + URB_IDLE = 0U, + URB_DONE, + URB_NOTREADY, + URB_ERROR, + URB_STALL +} usb_urb_state; + +typedef struct _usb_pipe +{ + uint8_t in_used; + uint8_t dev_addr; + uint32_t dev_speed; + + struct { + uint8_t num; + uint8_t dir; + uint8_t type; + uint16_t mps; + } ep; + + uint8_t ping; + uint32_t DPID; + + uint8_t *xfer_buf; + uint32_t xfer_len; + uint32_t xfer_count; + + uint8_t data_toggle_in; + uint8_t data_toggle_out; + + __IO uint32_t err_count; + __IO usb_pipe_staus pp_status; + __IO usb_urb_state urb_state; +} usb_pipe; + + +typedef struct _usb_host_drv +{ + uint8_t rx_buf[512U]; + __IO uint32_t connect_status; + __IO uint32_t port_enabled; + __IO uint32_t backup_xfercount[USBFS_MAX_TX_FIFOS]; + + usb_pipe pipe[USBFS_MAX_TX_FIFOS]; +} usb_host_drv; + +typedef struct _usb_core_driver +{ + usb_core_basic bp; + + usb_core_regs regs; + + usb_host_drv host; +} usb_core_driver; + +/* initializes USB core for host mode */ +usb_status usb_host_init (usb_core_driver *pudev); + +/* initialize host pipe */ +usb_status usb_pipe_init (usb_core_driver *pudev, uint8_t pipe_num); + +/* prepare host pipe for transferring packets */ +usb_status usb_pipe_xfer (usb_core_driver *pudev, uint8_t pipe_num); + +/* halt host pipe */ +usb_status usb_pipe_halt (usb_core_driver *pudev, uint8_t pipe_num); + +/* configure host pipe to do ping operation */ +usb_status usb_pipe_ping (usb_core_driver *pudev, uint8_t pipe_num); + +/* reset host port */ +uint32_t usb_port_reset (usb_core_driver *pudev); + +/* control the VBUS to power */ +void usb_portvbus_switch (usb_core_driver *pudev, uint8_t state); + +/* stop the USB host and clean up FIFO */ +void usb_host_stop (usb_core_driver *pudev); + +//__STATIC_INLINE uint8_t usb_frame_even (usb_core_driver *pudev) +uint32_t usb_frame_even (usb_core_driver *pudev); +//{ + // return !(pudev->regs.hr->HFINFR & 0x01U); +//} + +//__STATIC_INLINE void usb_phyclock_config (usb_core_driver *pudev, uint8_t clock) +void usb_phyclock_config (usb_core_driver *pudev, uint8_t clock) ; +//{ + //pudev->regs.hr->HCTL &= ~HCTL_CLKSEL; + // pudev->regs.hr->HCTL |= clock; +//} + +uint32_t usb_port_read (usb_core_driver *pudev); +//inline uint32_t usb_port_read (usb_core_driver *pudev) +//{ + // return *pudev->regs.HPCS & ~(HPCS_PE | HPCS_PCD | HPCS_PEDC); +//} + +uint32_t usb_curspeed_get (usb_core_driver *pudev); + +//inline uint32_t usb_curspeed_get (usb_core_driver *pudev) +//{ + // return *pudev->regs.HPCS & HPCS_PS; +//} + +//__STATIC_INLINE uint32_t usb_curframe_get (usb_core_driver *pudev) +uint32_t usb_curframe_get (usb_core_driver *pudev); +//{ + // return (pudev->regs.hr->HFINFR & 0xFFFFU); +//} + +#endif /* __DRV_USB_HOST_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_hw.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_hw.h new file mode 100644 index 00000000..4544548c --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_hw.h @@ -0,0 +1,61 @@ +/*! + \file drv_usb_hw.h + \brief usb hardware configuration header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USB_HW_H +#define __DRV_USB_HW_H + +#include "usb_conf.h" + +/* configure USB clock */ +void usb_rcu_config (void); + +/* configure USB interrupt */ +void usb_intr_config (void); + +/* initializes delay unit using Timer2 */ +void usb_timer_init (void); + +/* delay in micro seconds */ +void usb_udelay (const uint32_t usec); + +/* delay in milli seconds */ +void usb_mdelay (const uint32_t msec); + +// Functions for USE_HOST_MODE +/* configure USB VBus */ +void usb_vbus_config (void); +/* drive usb VBus */ +void usb_vbus_drive (uint8_t State); + +#endif /* __DRV_USB_HW_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_regs.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_regs.h new file mode 100644 index 00000000..725ff3b9 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usb_regs.h @@ -0,0 +1,666 @@ +/*! + \file drv_usb_regs.h + \brief USB cell registers definition and handle macros + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USB_REGS_H +#define __DRV_USB_REGS_H + +#include "usb_conf.h" + +#define USBHS_REG_BASE 0x40040000L /*!< base address of USBHS registers */ +#define USBFS_REG_BASE 0x50000000L /*!< base address of USBFS registers */ + +#define USBFS_MAX_TX_FIFOS 15 /*!< FIFO number */ + +#define USBFS_MAX_PACKET_SIZE 64U /*!< USBFS max packet size */ +#define USBFS_MAX_CHANNEL_COUNT 8U /*!< USBFS host channel count */ +#define USBFS_MAX_EP_COUNT 4U /*!< USBFS device endpoint count */ +#define USBFS_MAX_FIFO_WORDLEN 320U /*!< USBFS max fifo size in words */ + +#define USBHS_MAX_PACKET_SIZE 512U /*!< USBHS max packet size */ +#define USBHS_MAX_CHANNEL_COUNT 12U /*!< USBHS host channel count */ +#define USBHS_MAX_EP_COUNT 6U /*!< USBHS device endpoint count */ +#define USBHS_MAX_FIFO_WORDLEN 1280U /*!< USBHS max fifo size in words */ + +#define USB_DATA_FIFO_OFFSET 0x1000U /*!< USB data fifo offset */ +#define USB_DATA_FIFO_SIZE 0x1000U /*!< USB data fifo size */ + +typedef enum +{ + USB_CORE_ENUM_HS = 0, /*!< USB core type is HS */ + USB_CORE_ENUM_FS = 1 /*!< USB core type is FS */ +} usb_core_enum; + +enum usb_reg_offset { + USB_REG_OFFSET_CORE = 0x0000U, /*!< global OTG control and status register */ + USB_REG_OFFSET_DEV = 0x0800U, /*!< device mode control and status registers */ + USB_REG_OFFSET_EP = 0x0020U, + USB_REG_OFFSET_EP_IN = 0x0900U, /*!< device IN endpoint 0 control register */ + USB_REG_OFFSET_EP_OUT = 0x0B00U, /*!< device OUT endpoint 0 control register */ + USB_REG_OFFSET_HOST = 0x0400U, /*!< host control register */ + USB_REG_OFFSET_CH = 0x0020U, + USB_REG_OFFSET_PORT = 0x0440U, /*!< host port control and status register */ + USB_REG_OFFSET_CH_INOUT = 0x0500U, /*!< Host channel-x control registers */ + USB_REG_OFFSET_PWRCLKCTL = 0x0E00U, /*!< power and clock register */ +}; + +typedef struct +{ + __IO uint32_t GOTGCS; /*!< USB global OTG control and status register 000h */ + __IO uint32_t GOTGINTF; /*!< USB global OTG interrupt flag register 004h */ + __IO uint32_t GAHBCS; /*!< USB global AHB control and status register 008h */ + __IO uint32_t GUSBCS; /*!< USB global USB control and status register 00Ch */ + __IO uint32_t GRSTCTL; /*!< USB global reset control register 010h */ + __IO uint32_t GINTF; /*!< USB global interrupt flag register 014h */ + __IO uint32_t GINTEN; /*!< USB global interrupt enable register 018h */ + __IO uint32_t GRSTATR; /*!< USB receive status debug read register 01Ch */ + __IO uint32_t GRSTATP; /*!< USB receive status and pop register 020h */ + __IO uint32_t GRFLEN; /*!< USB global receive FIFO length register 024h */ + __IO uint32_t DIEP0TFLEN_HNPTFLEN; /*!< USB device IN endpoint 0/host non-periodic transmit FIFO length register 028h */ + __IO uint32_t HNPTFQSTAT; /*!< USB host non-periodic FIFO/queue status register 02Ch */ + uint32_t Reserved30[2]; /*!< Reserved 030h */ + __IO uint32_t GCCFG; /*!< USB global core configuration register 038h */ + __IO uint32_t CID; /*!< USB core ID register 03Ch */ + uint32_t Reserved40[48]; /*!< Reserved 040h-0FFh */ + __IO uint32_t HPTFLEN; /*!< USB host periodic transmit FIFO length register 100h */ + __IO uint32_t DIEPTFLEN[15]; /*!< USB device IN endpoint transmit FIFO length register 104h */ +} usb_gr; + + +typedef struct +{ + __IO uint32_t HCTL; /*!< USB host control register 400h */ + __IO uint32_t HFT; /*!< USB host frame interval register 404h */ + __IO uint32_t HFINFR; /*!< USB host frame information remaining register 408h */ + uint32_t Reserved40C; /*!< Reserved 40Ch */ + __IO uint32_t HPTFQSTAT; /*!< USB host periodic transmit FIFO/queue status register 410h */ + __IO uint32_t HACHINT; /*!< USB host all channels interrupt register 414h */ + __IO uint32_t HACHINTEN; /*!< USB host all channels interrupt enable register 418h */ +} usb_hr; + +typedef struct +{ + __IO uint32_t HCHCTL; /*!< USB host channel control register 500h */ + __IO uint32_t HCHSTCTL; /*!< Reserved 504h */ + __IO uint32_t HCHINTF; /*!< USB host channel interrupt flag register 508h */ + __IO uint32_t HCHINTEN; /*!< USB host channel interrupt enable register 50Ch */ + __IO uint32_t HCHLEN; /*!< USB host channel transfer length register 510h */ + __IO uint32_t HCHDMAADDR; /*!< USB host channel-x DMA address register 514h*/ + uint32_t Reserved[2]; +} usb_pr; + +typedef struct +{ + __IO uint32_t DCFG; /*!< USB device configuration register 800h */ + __IO uint32_t DCTL; /*!< USB device control register 804h */ + __IO uint32_t DSTAT; /*!< USB device status register 808h */ + uint32_t Reserved0C; /*!< Reserved 80Ch */ + __IO uint32_t DIEPINTEN; /*!< USB device IN endpoint common interrupt enable register 810h */ + __IO uint32_t DOEPINTEN; /*!< USB device OUT endpoint common interrupt enable register 814h */ + __IO uint32_t DAEPINT; /*!< USB device all endpoints interrupt register 818h */ + __IO uint32_t DAEPINTEN; /*!< USB device all endpoints interrupt enable register 81Ch */ + uint32_t Reserved20; /*!< Reserved 820h */ + uint32_t Reserved24; /*!< Reserved 824h */ + __IO uint32_t DVBUSDT; /*!< USB device VBUS discharge time register 828h */ + __IO uint32_t DVBUSPT; /*!< USB device VBUS pulsing time register 82Ch */ + __IO uint32_t DTHRCTL; /*!< dev thr 830h */ + __IO uint32_t DIEPFEINTEN; /*!< USB Device IN endpoint FIFO empty interrupt enable register 834h */ + __IO uint32_t DEP1INT; /*!< USB device endpoint 1 interrupt register 838h */ + __IO uint32_t DEP1INTEN; /*!< USB device endpoint 1 interrupt enable register 83Ch */ + uint32_t Reserved40; /*!< Reserved 840h */ + __IO uint32_t DIEP1INTEN; /*!< USB device IN endpoint-1 interrupt enable register 844h */ + uint32_t Reserved48[15]; /*!< Reserved 848-880h */ + __IO uint32_t DOEP1INTEN; /*!< USB device OUT endpoint-1 interrupt enable register 884h */ +} usb_dr; + +typedef struct +{ + __IO uint32_t DIEPCTL; /*!< USB device IN endpoint control register 900h + (EpNum * 20h) + 00h */ + uint32_t Reserved04; /*!< Reserved 900h + (EpNum * 20h) + 04h */ + __IO uint32_t DIEPINTF; /*!< USB device IN endpoint interrupt flag register 900h + (EpNum * 20h) + 08h */ + uint32_t Reserved0C; /*!< Reserved 900h + (EpNum * 20h) + 0Ch */ + __IO uint32_t DIEPLEN; /*!< USB device IN endpoint transfer length register 900h + (EpNum * 20h) + 10h */ + __IO uint32_t DIEPDMAADDR; /*!< Device IN endpoint-x DMA address register 900h + (EpNum * 20h) + 14h */ + __IO uint32_t DIEPTFSTAT; /*!< USB device IN endpoint transmit FIFO status register 900h + (EpNum * 20h) + 18h */ +} usb_erin; + +typedef struct +{ + __IO uint32_t DOEPCTL; /*!< USB device IN endpoint control register B00h + (EpNum * 20h) + 00h */ + uint32_t Reserved04; /*!< Reserved B00h + (EpNum * 20h) + 04h */ + __IO uint32_t DOEPINTF; /*!< USB device IN endpoint interrupt flag register B00h + (EpNum * 20h) + 08h */ + uint32_t Reserved0C; /*!< Reserved B00h + (EpNum * 20h) + 0Ch */ + __IO uint32_t DOEPLEN; /*!< USB device IN endpoint transfer length register B00h + (EpNum * 20h) + 10h */ + __IO uint32_t DOEPDMAADDR; /*!< Device OUT endpoint-x DMA address register B00h + (EpNum * 20h) + 0Ch */ +} usb_erout; + +typedef struct _usb_regs +{ + usb_gr *gr; /*!< USBFS global registers */ + usb_dr *dr; /*!< Device control and status registers */ + usb_hr *hr; /*!< Host control and status registers */ + usb_erin *er_in[6]; /*!< USB device IN endpoint register */ + usb_erout *er_out[6]; /*!< USB device OUT endpoint register */ + usb_pr *pr[15]; /*!< USB Host channel-x control register */ + + __IO uint32_t *HPCS; /*!< USB host port control and status register */ + __IO uint32_t *DFIFO[USBFS_MAX_TX_FIFOS]; + __IO uint32_t *PWRCLKCTL; /*!< USB power and clock control register */ +} usb_core_regs; + +/* global OTG control and status register bits definitions */ +#define GOTGCS_BSV BIT(19) /*!< B-Session Valid */ +#define GOTGCS_ASV BIT(18) /*!< A-session valid */ +#define GOTGCS_DI BIT(17) /*!< debounce interval */ +#define GOTGCS_CIDPS BIT(16) /*!< id pin status */ +#define GOTGCS_DHNPEN BIT(11) /*!< device HNP enable */ +#define GOTGCS_HHNPEN BIT(10) /*!< host HNP enable */ +#define GOTGCS_HNPREQ BIT(9) /*!< HNP request */ +#define GOTGCS_HNPS BIT(8) /*!< HNP successes */ +#define GOTGCS_SRPREQ BIT(1) /*!< SRP request */ +#define GOTGCS_SRPS BIT(0) /*!< SRP successes */ + +/* global OTG interrupt flag register bits definitions */ +#define GOTGINTF_DF BIT(19) /*!< debounce finish */ +#define GOTGINTF_ADTO BIT(18) /*!< A-device timeout */ +#define GOTGINTF_HNPDET BIT(17) /*!< host negotiation request detected */ +#define GOTGINTF_HNPEND BIT(9) /*!< HNP end */ +#define GOTGINTF_SRPEND BIT(8) /*!< SRP end */ +#define GOTGINTF_SESEND BIT(2) /*!< session end */ + +/* global AHB control and status register bits definitions */ +#define GAHBCS_PTXFTH BIT(8) /*!< periodic Tx FIFO threshold */ +#define GAHBCS_TXFTH BIT(7) /*!< tx FIFO threshold */ +#define GAHBCS_DMAEN BIT(5) /*!< DMA function Enable */ +#define GAHBCS_BURST BITS(1, 4) /*!< the AHB burst type used by DMA */ +#define GAHBCS_GINTEN BIT(0) /*!< global interrupt enable */ + +/* global USB control and status register bits definitions */ +#define GUSBCS_FDM BIT(30) /*!< force device mode */ +#define GUSBCS_FHM BIT(29) /*!< force host mode */ +#define GUSBCS_ULPIEOI BIT(21) /*!< ULPI external over-current indicator */ +#define GUSBCS_ULPIEVD BIT(20) /*!< ULPI external VBUS driver */ +#define GUSBCS_UTT BITS(10, 13) /*!< USB turnaround time */ +#define GUSBCS_HNPCEN BIT(9) /*!< HNP capability enable */ +#define GUSBCS_SRPCEN BIT(8) /*!< SRP capability enable */ +#define GUSBCS_EMBPHY BIT(6) /*!< embedded PHY selected */ +#define GUSBCS_TOC BITS(0, 2) /*!< timeout calibration */ + +/* global reset control register bits definitions */ +#define GRSTCTL_DMAIDL BIT(31) /*!< DMA idle state */ +#define GRSTCTL_DMABSY BIT(30) /*!< DMA busy */ +#define GRSTCTL_TXFNUM BITS(6, 10) /*!< tx FIFO number */ +#define GRSTCTL_TXFF BIT(5) /*!< tx FIFO flush */ +#define GRSTCTL_RXFF BIT(4) /*!< rx FIFO flush */ +#define GRSTCTL_HFCRST BIT(2) /*!< host frame counter reset */ +#define GRSTCTL_HCSRST BIT(1) /*!< HCLK soft reset */ +#define GRSTCTL_CSRST BIT(0) /*!< core soft reset */ + +/* global interrupt flag register bits definitions */ +#define GINTF_WKUPIF BIT(31) /*!< wakeup interrupt flag */ +#define GINTF_SESIF BIT(30) /*!< session interrupt flag */ +#define GINTF_DISCIF BIT(29) /*!< disconnect interrupt flag */ +#define GINTF_IDPSC BIT(28) /*!< id pin status change */ +#define GINTF_PTXFEIF BIT(26) /*!< periodic tx FIFO empty interrupt flag */ +#define GINTF_HCIF BIT(25) /*!< host channels interrupt flag */ +#define GINTF_HPIF BIT(24) /*!< host port interrupt flag */ +#define GINTF_PXNCIF BIT(21) /*!< periodic transfer not complete interrupt flag */ +#define GINTF_ISOONCIF BIT(21) /*!< isochronous OUT transfer not complete interrupt flag */ +#define GINTF_ISOINCIF BIT(20) /*!< isochronous IN transfer not complete interrupt flag */ +#define GINTF_OEPIF BIT(19) /*!< OUT endpoint interrupt flag */ +#define GINTF_IEPIF BIT(18) /*!< IN endpoint interrupt flag */ +#define GINTF_EOPFIF BIT(15) /*!< end of periodic frame interrupt flag */ +#define GINTF_ISOOPDIF BIT(14) /*!< isochronous OUT packet dropped interrupt flag */ +#define GINTF_ENUMFIF BIT(13) /*!< enumeration finished */ +#define GINTF_RST BIT(12) /*!< USB reset */ +#define GINTF_SP BIT(11) /*!< USB suspend */ +#define GINTF_ESP BIT(10) /*!< early suspend */ +#define GINTF_GONAK BIT(7) /*!< global OUT NAK effective */ +#define GINTF_GNPINAK BIT(6) /*!< global IN non-periodic NAK effective */ +#define GINTF_NPTXFEIF BIT(5) /*!< non-periodic tx FIFO empty interrupt flag */ +#define GINTF_RXFNEIF BIT(4) /*!< rx FIFO non-empty interrupt flag */ +#define GINTF_SOF BIT(3) /*!< start of frame */ +#define GINTF_OTGIF BIT(2) /*!< OTG interrupt flag */ +#define GINTF_MFIF BIT(1) /*!< mode fault interrupt flag */ +#define GINTF_COPM BIT(0) /*!< current operation mode */ + +/* global interrupt enable register bits definitions */ +#define GINTEN_WKUPIE BIT(31) /*!< wakeup interrupt enable */ +#define GINTEN_SESIE BIT(30) /*!< session interrupt enable */ +#define GINTEN_DISCIE BIT(29) /*!< disconnect interrupt enable */ +#define GINTEN_IDPSCIE BIT(28) /*!< id pin status change interrupt enable */ +#define GINTEN_PTXFEIE BIT(26) /*!< periodic tx FIFO empty interrupt enable */ +#define GINTEN_HCIE BIT(25) /*!< host channels interrupt enable */ +#define GINTEN_HPIE BIT(24) /*!< host port interrupt enable */ +#define GINTEN_IPXIE BIT(21) /*!< periodic transfer not complete interrupt enable */ +#define GINTEN_ISOONCIE BIT(21) /*!< isochronous OUT transfer not complete interrupt enable */ +#define GINTEN_ISOINCIE BIT(20) /*!< isochronous IN transfer not complete interrupt enable */ +#define GINTEN_OEPIE BIT(19) /*!< OUT endpoints interrupt enable */ +#define GINTEN_IEPIE BIT(18) /*!< IN endpoints interrupt enable */ +#define GINTEN_EOPFIE BIT(15) /*!< end of periodic frame interrupt enable */ +#define GINTEN_ISOOPDIE BIT(14) /*!< isochronous OUT packet dropped interrupt enable */ +#define GINTEN_ENUMFIE BIT(13) /*!< enumeration finish enable */ +#define GINTEN_RSTIE BIT(12) /*!< USB reset interrupt enable */ +#define GINTEN_SPIE BIT(11) /*!< USB suspend interrupt enable */ +#define GINTEN_ESPIE BIT(10) /*!< early suspend interrupt enable */ +#define GINTEN_GONAKIE BIT(7) /*!< global OUT NAK effective interrupt enable */ +#define GINTEN_GNPINAKIE BIT(6) /*!< global non-periodic IN NAK effective interrupt enable */ +#define GINTEN_NPTXFEIE BIT(5) /*!< non-periodic Tx FIFO empty interrupt enable */ +#define GINTEN_RXFNEIE BIT(4) /*!< receive FIFO non-empty interrupt enable */ +#define GINTEN_SOFIE BIT(3) /*!< start of frame interrupt enable */ +#define GINTEN_OTGIE BIT(2) /*!< OTG interrupt enable */ +#define GINTEN_MFIE BIT(1) /*!< mode fault interrupt enable */ + +/* global receive status read and pop register bits definitions */ +#define GRSTATRP_RPCKST BITS(17, 20) /*!< received packet status */ +#define GRSTATRP_DPID BITS(15, 16) /*!< data PID */ +#define GRSTATRP_BCOUNT BITS(4, 14) /*!< byte count */ +#define GRSTATRP_CNUM BITS(0, 3) /*!< channel number */ +#define GRSTATRP_EPNUM BITS(0, 3) /*!< endpoint number */ + +/* global receive FIFO length register bits definitions */ +#define GRFLEN_RXFD BITS(0, 15) /*!< rx FIFO depth */ + +/* host non-periodic transmit FIFO length register bits definitions */ +#define HNPTFLEN_HNPTXFD BITS(16, 31) /*!< non-periodic Tx FIFO depth */ +#define HNPTFLEN_HNPTXRSAR BITS(0, 15) /*!< non-periodic Tx RAM start address */ + +/** + * @brief USB IN endpoint 0 transmit FIFO length register bits definitions + */ +#define DIEP0TFLEN_IEP0TXFD BITS(16, 31) /*!< IN Endpoint 0 Tx FIFO depth */ +#define DIEP0TFLEN_IEP0TXRSAR BITS(0, 15) /*!< IN Endpoint 0 TX RAM start address */ + +/* host non-periodic transmit FIFO/queue status register bits definitions */ +#define HNPTFQSTAT_NPTXRQTOP BITS(24, 30) /*!< top entry of the non-periodic Tx request queue */ +#define HNPTFQSTAT_NPTXRQS BITS(16, 23) /*!< non-periodic Tx request queue space */ +#define HNPTFQSTAT_NPTXFS BITS(0, 15) /*!< non-periodic Tx FIFO space */ +#define HNPTFQSTAT_CNUM BITS(27, 30) /*!< channel number*/ +#define HNPTFQSTAT_EPNUM BITS(27, 30) /*!< endpoint number */ +#define HNPTFQSTAT_TYPE BITS(25, 26) /*!< token type */ +#define HNPTFQSTAT_TMF BIT(24) /*!< terminate flag */ + +/* global core configuration register bits definitions */ +#define GCCFG_VBUSIG BIT(21) /*!< vbus ignored */ +#define GCCFG_SOFOEN BIT(20) /*!< SOF output enable */ +#define GCCFG_VBUSBCEN BIT(19) /*!< the VBUS B-device comparer enable */ +#define GCCFG_VBUSACEN BIT(18) /*!< the VBUS A-device comparer enable */ +#define GCCFG_PWRON BIT(16) /*!< power on */ + +/* core ID register bits definitions */ +#define CID_CID BITS(0, 31) /*!< core ID */ + +/* host periodic transmit FIFO length register bits definitions */ +#define HPTFLEN_HPTXFD BITS(16, 31) /*!< host periodic Tx FIFO depth */ +#define HPTFLEN_HPTXFSAR BITS(0, 15) /*!< host periodic Tx RAM start address */ + +/* device IN endpoint transmit FIFO length register bits definitions */ +#define DIEPTFLEN_IEPTXFD BITS(16, 31) /*!< IN endpoint Tx FIFO x depth */ +#define DIEPTFLEN_IEPTXRSAR BITS(0, 15) /*!< IN endpoint FIFOx Tx x RAM start address */ + +/* host control register bits definitions */ +#define HCTL_SPDFSLS BIT(2) /*!< speed limited to FS and LS */ +#define HCTL_CLKSEL BITS(0, 1) /*!< clock select for USB clock */ + +/* host frame interval register bits definitions */ +#define HFT_FRI BITS(0, 15) /*!< frame interval */ + +/* host frame information remaining register bits definitions */ +#define HFINFR_FRT BITS(16, 31) /*!< frame remaining time */ +#define HFINFR_FRNUM BITS(0, 15) /*!< frame number */ + +/* host periodic transmit FIFO/queue status register bits definitions */ +#define HPTFQSTAT_PTXREQT BITS(24, 31) /*!< top entry of the periodic Tx request queue */ +#define HPTFQSTAT_PTXREQS BITS(16, 23) /*!< periodic Tx request queue space */ +#define HPTFQSTAT_PTXFS BITS(0, 15) /*!< periodic Tx FIFO space */ +#define HPTFQSTAT_OEFRM BIT(31) /*!< odd/eveb frame */ +#define HPTFQSTAT_CNUM BITS(27, 30) /*!< channel number */ +#define HPTFQSTAT_EPNUM BITS(27, 30) /*!< endpoint number */ +#define HPTFQSTAT_TYPE BITS(25, 26) /*!< token type */ +#define HPTFQSTAT_TMF BIT(24) /*!< terminate flag */ + + +#define TFQSTAT_TXFS BITS(0, 15) +#define TFQSTAT_CNUM BITS(27, 30) + +/* host all channels interrupt register bits definitions */ +#define HACHINT_HACHINT BITS(0, 11) /*!< host all channel interrupts */ + +/* host all channels interrupt enable register bits definitions */ +#define HACHINTEN_CINTEN BITS(0, 11) /*!< channel interrupt enable */ + +/* host port control and status register bits definitions */ +#define HPCS_PS BITS(17, 18) /*!< port speed */ +#define HPCS_PP BIT(12) /*!< port power */ +#define HPCS_PLST BITS(10, 11) /*!< port line status */ +#define HPCS_PRST BIT(8) /*!< port reset */ +#define HPCS_PSP BIT(7) /*!< port suspend */ +#define HPCS_PREM BIT(6) /*!< port resume */ +#define HPCS_PEDC BIT(3) /*!< port enable/disable change */ +#define HPCS_PE BIT(2) /*!< port enable */ +#define HPCS_PCD BIT(1) /*!< port connect detected */ +#define HPCS_PCST BIT(0) /*!< port connect status */ + +/* host channel-x control register bits definitions */ +#define HCHCTL_CEN BIT(31) /*!< channel enable */ +#define HCHCTL_CDIS BIT(30) /*!< channel disable */ +#define HCHCTL_ODDFRM BIT(29) /*!< odd frame */ +#define HCHCTL_DAR BITS(22, 28) /*!< device address */ +#define HCHCTL_MPC BITS(20, 21) /*!< multiple packet count */ +#define HCHCTL_EPTYPE BITS(18, 19) /*!< endpoint type */ +#define HCHCTL_LSD BIT(17) /*!< low-speed device */ +#define HCHCTL_EPDIR BIT(15) /*!< endpoint direction */ +#define HCHCTL_EPNUM BITS(11, 14) /*!< endpoint number */ +#define HCHCTL_MPL BITS(0, 10) /*!< maximum packet length */ + +/* host channel-x split transaction register bits definitions */ +#define HCHSTCTL_SPLEN BIT(31) /*!< enable high-speed split transaction */ +#define HCHSTCTL_CSPLT BIT(16) /*!< complete-split enable */ +#define HCHSTCTL_ISOPCE BITS(14, 15) /*!< isochronous OUT payload continuation encoding */ +#define HCHSTCTL_HADDR BITS(7, 13) /*!< HUB address */ +#define HCHSTCTL_PADDR BITS(0, 6) /*!< port address */ + +/* host channel-x interrupt flag register bits definitions */ +#define HCHINTF_DTER BIT(10) /*!< data toggle error */ +#define HCHINTF_REQOVR BIT(9) /*!< request queue overrun */ +#define HCHINTF_BBER BIT(8) /*!< babble error */ +#define HCHINTF_USBER BIT(7) /*!< USB bus Error */ +#define HCHINTF_NYET BIT(6) /*!< NYET */ +#define HCHINTF_ACK BIT(5) /*!< ACK */ +#define HCHINTF_NAK BIT(4) /*!< NAK */ +#define HCHINTF_STALL BIT(3) /*!< STALL */ +#define HCHINTF_DMAER BIT(2) /*!< DMA error */ +#define HCHINTF_CH BIT(1) /*!< channel halted */ +#define HCHINTF_TF BIT(0) /*!< transfer finished */ + +/* host channel-x interrupt enable register bits definitions */ +#define HCHINTEN_DTERIE BIT(10) /*!< data toggle error interrupt enable */ +#define HCHINTEN_REQOVRIE BIT(9) /*!< request queue overrun interrupt enable */ +#define HCHINTEN_BBERIE BIT(8) /*!< babble error interrupt enable */ +#define HCHINTEN_USBERIE BIT(7) /*!< USB bus error interrupt enable */ +#define HCHINTEN_NYETIE BIT(6) /*!< NYET interrupt enable */ +#define HCHINTEN_ACKIE BIT(5) /*!< ACK interrupt enable */ +#define HCHINTEN_NAKIE BIT(4) /*!< NAK interrupt enable */ +#define HCHINTEN_STALLIE BIT(3) /*!< STALL interrupt enable */ +#define HCHINTEN_DMAERIE BIT(2) /*!< DMA error interrupt enable */ +#define HCHINTEN_CHIE BIT(1) /*!< channel halted interrupt enable */ +#define HCHINTEN_TFIE BIT(0) /*!< transfer finished interrupt enable */ + +/* host channel-x transfer length register bits definitions */ +#define HCHLEN_PING BIT(31) /*!< PING token request */ +#define HCHLEN_DPID BITS(29, 30) /*!< data PID */ +#define HCHLEN_PCNT BITS(19, 28) /*!< packet count */ +#define HCHLEN_TLEN BITS(0, 18) /*!< transfer length */ + +/* host channel-x DMA address register bits definitions */ +#define HCHDMAADDR_DMAADDR BITS(0, 31) /*!< DMA address */ + + +#define PORT_SPEED(x) (((uint32_t)(x) << 17) & HPCS_PS) /*!< Port speed */ + +#define PORT_SPEED_HIGH PORT_SPEED(0) /*!< high speed */ +#define PORT_SPEED_FULL PORT_SPEED(1) /*!< full speed */ +#define PORT_SPEED_LOW PORT_SPEED(2) /*!< low speed */ + +#define PIPE_CTL_DAR(x) (((uint32_t)(x) << 22) & HCHCTL_DAR) /*!< device address */ +#define PIPE_CTL_EPTYPE(x) (((uint32_t)(x) << 18) & HCHCTL_EPTYPE) /*!< endpoint type */ +#define PIPE_CTL_EPNUM(x) (((uint32_t)(x) << 11) & HCHCTL_EPNUM) /*!< endpoint number */ +#define PIPE_CTL_EPDIR(x) (((uint32_t)(x) << 15) & HCHCTL_EPDIR) /*!< endpoint direction */ +#define PIPE_CTL_EPMPL(x) (((uint32_t)(x) << 0) & HCHCTL_MPL) /*!< maximum packet length */ +#define PIPE_CTL_LSD(x) (((uint32_t)(x) << 17) & HCHCTL_LSD) /*!< low-Speed device */ + +#define PIPE_XFER_PCNT(x) (((uint32_t)(x) << 19) & HCHLEN_PCNT) /*!< packet count */ +#define PIPE_XFER_DPID(x) (((uint32_t)(x) << 29) & HCHLEN_DPID) /*!< data PID */ + +#define PIPE_DPID_DATA0 PIPE_XFER_DPID(0) /*!< DATA0 */ +#define PIPE_DPID_DATA1 PIPE_XFER_DPID(2) /*!< DATA1 */ +#define PIPE_DPID_DATA2 PIPE_XFER_DPID(1) /*!< DATA2 */ +#define PIPE_DPID_SETUP PIPE_XFER_DPID(3) /*!< MDATA (non-control)/SETUP (control) */ + +extern const uint32_t PIPE_DPID[]; + +/* device configuration registers bits definitions */ +#define DCFG_EOPFT BITS(11, 12) /*!< end of periodic frame time */ +#define DCFG_DAR BITS(4, 10) /*!< device address */ +#define DCFG_NZLSOH BIT(2) /*!< non-zero-length status OUT handshake */ +#define DCFG_DS BITS(0, 1) /*!< device speed */ + +/* device control registers bits definitions */ +#define DCTL_POIF BIT(11) /*!< power-on initialization finished */ +#define DCTL_CGONAK BIT(10) /*!< clear global OUT NAK */ +#define DCTL_SGONAK BIT(9) /*!< set global OUT NAK */ +#define DCTL_CGINAK BIT(8) /*!< clear global IN NAK */ +#define DCTL_SGINAK BIT(7) /*!< set global IN NAK */ +#define DCTL_GONS BIT(3) /*!< global OUT NAK status */ +#define DCTL_GINS BIT(2) /*!< global IN NAK status */ +#define DCTL_SD BIT(1) /*!< soft disconnect */ +#define DCTL_RWKUP BIT(0) /*!< remote wakeup */ + +/* device status registers bits definitions */ +#define DSTAT_FNRSOF BITS(8, 21) /*!< the frame number of the received SOF. */ +#define DSTAT_ES BITS(1, 2) /*!< enumerated speed */ +#define DSTAT_SPST BIT(0) /*!< suspend status */ + +/* device IN endpoint common interrupt enable registers bits definitions */ +#define DIEPINTEN_NAKEN BIT(13) /*!< NAK handshake sent by USBHS interrupt enable bit */ +#define DIEPINTEN_TXFEEN BIT(7) /*!< transmit FIFO empty interrupt enable bit */ +#define DIEPINTEN_IEPNEEN BIT(6) /*!< IN endpoint NAK effective interrupt enable bit */ +#define DIEPINTEN_EPTXFUDEN BIT(4) /*!< endpoint Tx FIFO underrun interrupt enable bit */ +#define DIEPINTEN_CITOEN BIT(3) /*!< control In Timeout interrupt enable bit */ +#define DIEPINTEN_EPDISEN BIT(1) /*!< endpoint disabled interrupt enable bit */ +#define DIEPINTEN_TFEN BIT(0) /*!< transfer finished interrupt enable bit */ + +/* device OUT endpoint common interrupt enable registers bits definitions */ +#define DOEPINTEN_NYETEN BIT(14) /*!< NYET handshake is sent interrupt enable bit */ +#define DOEPINTEN_BTBSTPEN BIT(6) /*!< back-to-back SETUP packets interrupt enable bit */ +#define DOEPINTEN_EPRXFOVREN BIT(4) /*!< endpoint Rx FIFO overrun interrupt enable bit */ +#define DOEPINTEN_STPFEN BIT(3) /*!< SETUP phase finished interrupt enable bit */ +#define DOEPINTEN_EPDISEN BIT(1) /*!< endpoint disabled interrupt enable bit */ +#define DOEPINTEN_TFEN BIT(0) /*!< transfer finished interrupt enable bit */ + +/* device all endpoints interrupt registers bits definitions */ +#define DAEPINT_OEPITB BITS(16, 21) /*!< device all OUT endpoint interrupt bits */ +#define DAEPINT_IEPITB BITS(0, 5) /*!< device all IN endpoint interrupt bits */ + +/* device all endpoints interrupt enable registers bits definitions */ +#define DAEPINTEN_OEPIE BITS(16, 21) /*!< OUT endpoint interrupt enable */ +#define DAEPINTEN_IEPIE BITS(0, 3) /*!< IN endpoint interrupt enable */ + +/* device Vbus discharge time registers bits definitions */ +#define DVBUSDT_DVBUSDT BITS(0, 15) /*!< device VBUS discharge time */ + +/* device Vbus pulsing time registers bits definitions */ +#define DVBUSPT_DVBUSPT BITS(0, 11) /*!< device VBUS pulsing time */ + +/* device IN endpoint FIFO empty interrupt enable register bits definitions */ +#define DIEPFEINTEN_IEPTXFEIE BITS(0, 5) /*!< IN endpoint Tx FIFO empty interrupt enable bits */ + +/* device endpoint 0 control register bits definitions */ +#define DEP0CTL_EPEN BIT(31) /*!< endpoint enable */ +#define DEP0CTL_EPD BIT(30) /*!< endpoint disable */ +#define DEP0CTL_SNAK BIT(27) /*!< set NAK */ +#define DEP0CTL_CNAK BIT(26) /*!< clear NAK */ +#define DIEP0CTL_TXFNUM BITS(22, 25) /*!< tx FIFO number */ +#define DEP0CTL_STALL BIT(21) /*!< STALL handshake */ +#define DOEP0CTL_SNOOP BIT(20) /*!< snoop mode */ +#define DEP0CTL_EPTYPE BITS(18, 19) /*!< endpoint type */ +#define DEP0CTL_NAKS BIT(17) /*!< NAK status */ +#define DEP0CTL_EPACT BIT(15) /*!< endpoint active */ +#define DEP0CTL_MPL BITS(0, 1) /*!< maximum packet length */ + +/* device endpoint x control register bits definitions */ +#define DEPCTL_EPEN BIT(31) /*!< endpoint enable */ +#define DEPCTL_EPD BIT(30) /*!< endpoint disable */ +#define DEPCTL_SODDFRM BIT(29) /*!< set odd frame */ +#define DEPCTL_SD1PID BIT(29) /*!< set DATA1 PID */ +#define DEPCTL_SEVNFRM BIT(28) /*!< set even frame */ +#define DEPCTL_SD0PID BIT(28) /*!< set DATA0 PID */ +#define DEPCTL_SNAK BIT(27) /*!< set NAK */ +#define DEPCTL_CNAK BIT(26) /*!< clear NAK */ +#define DIEPCTL_TXFNUM BITS(22, 25) /*!< tx FIFO number */ +#define DEPCTL_STALL BIT(21) /*!< STALL handshake */ +#define DOEPCTL_SNOOP BIT(20) /*!< snoop mode */ +#define DEPCTL_EPTYPE BITS(18, 19) /*!< endpoint type */ +#define DEPCTL_NAKS BIT(17) /*!< NAK status */ +#define DEPCTL_EOFRM BIT(16) /*!< even/odd frame */ +#define DEPCTL_DPID BIT(16) /*!< endpoint data PID */ +#define DEPCTL_EPACT BIT(15) /*!< endpoint active */ +#define DEPCTL_MPL BITS(0, 10) /*!< maximum packet length */ + +/* device IN endpoint-x interrupt flag register bits definitions */ +#define DIEPINTF_NAK BIT(13) /*!< NAK handshake sent by USBHS */ +#define DIEPINTF_TXFE BIT(7) /*!< transmit FIFO empty */ +#define DIEPINTF_IEPNE BIT(6) /*!< IN endpoint NAK effective */ +#define DIEPINTF_EPTXFUD BIT(4) /*!< endpoint Tx FIFO underrun */ +#define DIEPINTF_CITO BIT(3) /*!< control In Timeout interrupt */ +#define DIEPINTF_EPDIS BIT(1) /*!< endpoint disabled */ +#define DIEPINTF_TF BIT(0) /*!< transfer finished */ + +/* device OUT endpoint-x interrupt flag register bits definitions */ +#define DOEPINTF_NYET BIT(14) /*!< NYET handshake is sent */ +#define DOEPINTF_BTBSTP BIT(6) /*!< back-to-back SETUP packets */ +#define DOEPINTF_EPRXFOVR BIT(4) /*!< endpoint Rx FIFO overrun */ +#define DOEPINTF_STPF BIT(3) /*!< SETUP phase finished */ +#define DOEPINTF_EPDIS BIT(1) /*!< endpoint disabled */ +#define DOEPINTF_TF BIT(0) /*!< transfer finished */ + +/* device IN endpoint 0 transfer length register bits definitions */ +#define DIEP0LEN_PCNT BITS(19, 20) /*!< packet count */ +#define DIEP0LEN_TLEN BITS(0, 6) /*!< transfer length */ + +/* device OUT endpoint 0 transfer length register bits definitions */ +#define DOEP0LEN_STPCNT BITS(29, 30) /*!< SETUP packet count */ +#define DOEP0LEN_PCNT BIT(19) /*!< packet count */ +#define DOEP0LEN_TLEN BITS(0, 6) /*!< transfer length */ + +/* device OUT endpoint-x transfer length register bits definitions */ +#define DOEPLEN_RXDPID BITS(29, 30) /*!< received data PID */ +#define DOEPLEN_STPCNT BITS(29, 30) /*!< SETUP packet count */ +#define DIEPLEN_MCNT BITS(29, 30) /*!< multi count */ +#define DEPLEN_PCNT BITS(19, 28) /*!< packet count */ +#define DEPLEN_TLEN BITS(0, 18) /*!< transfer length */ + +/* device IN endpoint-x DMA address register bits definitions */ +#define DIEPDMAADDR_DMAADDR BITS(0, 31) /*!< DMA address */ + +/* device OUT endpoint-x DMA address register bits definitions */ +#define DOEPDMAADDR_DMAADDR BITS(0, 31) /*!< DMA address */ + +/* device IN endpoint-x transmit FIFO status register bits definitions */ +#define DIEPTFSTAT_IEPTFS BITS(0, 15) /*!< IN endpoint Tx FIFO space remaining */ + +/* USB power and clock registers bits definition */ +#define PWRCLKCTL_SHCLK BIT(1) /*!< stop HCLK */ +#define PWRCLKCTL_SUCLK BIT(0) /*!< stop the USB clock */ + +#define RSTAT_GOUT_NAK 1U /* global OUT NAK (triggers an interrupt) */ +#define RSTAT_DATA_UPDT 2U /* OUT data packet received */ +#define RSTAT_XFER_COMP 3U /* OUT transfer completed (triggers an interrupt) */ +#define RSTAT_SETUP_COMP 4U /* SETUP transaction completed (triggers an interrupt) */ +#define RSTAT_SETUP_UPDT 6U /* SETUP data packet received */ + +#define DSTAT_EM_HS_PHY_30MHZ_60MHZ 0U /* USB enumerate speed use high-speed PHY clock in 30MHz or 60MHz */ +#define DSTAT_EM_FS_PHY_30MHZ_60MHZ 1U /* USB enumerate speed use full-speed PHY clock in 30MHz or 60MHz */ +#define DSTAT_EM_LS_PHY_6MHZ 2U /* USB enumerate speed use low-speed PHY clock in 6MHz */ +#define DSTAT_EM_FS_PHY_48MHZ 3U /* USB enumerate speed use full-speed PHY clock in 48MHz */ + +#define DPID_DATA0 0U /* device endpoint data PID is DATA0 */ +#define DPID_DATA1 2U /* device endpoint data PID is DATA1 */ +#define DPID_DATA2 1U /* device endpoint data PID is DATA2 */ +#define DPID_MDATA 3U /* device endpoint data PID is MDATA */ + +#define GAHBCS_DMAINCR(regval) (GAHBCS_BURST & ((regval) << 1U)) /*!< AHB burst type used by DMA*/ + +#define DMA_INCR0 GAHBCS_DMAINCR(0U) /*!< single burst type used by DMA*/ +#define DMA_INCR1 GAHBCS_DMAINCR(1U) /*!< 4-beat incrementing burst type used by DMA*/ +#define DMA_INCR4 GAHBCS_DMAINCR(3U) /*!< 8-beat incrementing burst type used by DMA*/ +#define DMA_INCR8 GAHBCS_DMAINCR(5U) /*!< 16-beat incrementing burst type used by DMA*/ +#define DMA_INCR16 GAHBCS_DMAINCR(7U) /*!< 32-beat incrementing burst type used by DMA*/ + +#define DCFG_PFRI(regval) (DCFG_EOPFT & ((regval) << 11U)) /*!< end of periodic frame time configuration */ + +#define FRAME_INTERVAL_80 DCFG_PFRI(0U) /*!< 80% of the frame time */ +#define FRAME_INTERVAL_85 DCFG_PFRI(1U) /*!< 85% of the frame time */ +#define FRAME_INTERVAL_90 DCFG_PFRI(2U) /*!< 90% of the frame time */ +#define FRAME_INTERVAL_95 DCFG_PFRI(3U) /*!< 95% of the frame time */ + +#define DCFG_DEVSPEED(regval) (DCFG_DS & ((regval) << 0U)) /*!< device speed configuration */ + +#define USB_SPEED_EXP_HIGH DCFG_DEVSPEED(0U) /*!< device external PHY high speed */ +#define USB_SPEED_EXP_FULL DCFG_DEVSPEED(1U) /*!< device external PHY full speed */ +#define USB_SPEED_INP_FULL DCFG_DEVSPEED(3U) /*!< device internal PHY full speed */ + +#define DEP0_MPL(regval) (DEP0CTL_MPL & ((regval) << 0U)) /*!< maximum packet length configuration */ + +#define EP0MPL_64 DEP0_MPL(0U) /*!< maximum packet length 64 bytes */ +#define EP0MPL_32 DEP0_MPL(1U) /*!< maximum packet length 32 bytes */ +#define EP0MPL_16 DEP0_MPL(2U) /*!< maximum packet length 16 bytes */ +#define EP0MPL_8 DEP0_MPL(3U) /*!< maximum packet length 8 bytes */ + +#define DOEP0_TLEN(regval) (DOEP0LEN_TLEN & ((regval) << 0)) /*!< Transfer length */ +#define DOEP0_PCNT(regval) (DOEP0LEN_PCNT & ((regval) << 19)) /*!< Packet count */ +#define DOEP0_STPCNT(regval) (DOEP0LEN_STPCNT & ((regval) << 29)) /*!< SETUP packet count */ + +#define USB_ULPI_PHY 1 /*!< ULPI interface external PHY */ +#define USB_EMBEDDED_PHY 2 /*!< Embedded PHY */ + +#define GRXSTS_PKTSTS_IN 2 +#define GRXSTS_PKTSTS_IN_XFER_COMP 3 +#define GRXSTS_PKTSTS_DATA_TOGGLE_ERR 5 +#define GRXSTS_PKTSTS_CH_HALTED 7 + +#define DEVICE_MODE 0 /*!< device mode */ +#define HOST_MODE 1 /*!< host mode */ +#define OTG_MODE 2 /*!< OTG mode */ + +#define HCTL_30_60MHZ 0 /*!< USB clock 30-60MHZ */ +#define HCTL_48MHZ 1 /*!< USB clock 48MHZ */ +#define HCTL_6MHZ 2 /*!< USB clock 6MHZ */ + +enum USB_SPEED { + USB_SPEED_UNKNOWN = 0, /*!< USB speed unknown */ + USB_SPEED_LOW, /*!< USB speed low */ + USB_SPEED_FULL, /*!< USB speed full */ + USB_SPEED_HIGH /*!< USB speed high */ +}; + +#define EP0_OUT ((uint8_t)0x00) /*!< endpoint out 0 */ +#define EP0_IN ((uint8_t)0x80) /*!< endpoint in 0 */ +#define EP1_OUT ((uint8_t)0x01) /*!< endpoint out 1 */ +#define EP1_IN ((uint8_t)0x81) /*!< endpoint in 1 */ +#define EP2_OUT ((uint8_t)0x02) /*!< endpoint out 2 */ +#define EP2_IN ((uint8_t)0x82) /*!< endpoint in 2 */ +#define EP3_OUT ((uint8_t)0x03) /*!< endpoint out 3 */ +#define EP3_IN ((uint8_t)0x83) /*!< endpoint in 3 */ + +#endif /* __DRV_USB_REGS_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbd_int.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbd_int.h new file mode 100644 index 00000000..67f954c8 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbd_int.h @@ -0,0 +1,52 @@ +/*! + \file drv_usbd_int.h + \brief USB device mode interrupt header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USBD_INT_H +#define __DRV_USBD_INT_H + +#include "drv_usb_core.h" +#include "drv_usb_dev.h" + +/* USB device-mode interrupts global service routine handler */ +void usbd_isr (usb_core_driver *udev); + +#ifdef USB_HS_DEDICATED_EP1_ENABLED + +uint32_t USBD_OTG_EP1IN_ISR_Handler (usb_core_driver *udev); +uint32_t USBD_OTG_EP1OUT_ISR_Handler (usb_core_driver *udev); + +#endif + +#endif /* __DRV_USBD_INT_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbh_int.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbh_int.h new file mode 100644 index 00000000..4607fa1b --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/drv_usbh_int.h @@ -0,0 +1,49 @@ +/*! + \file drv_usbh_int.h.h + \brief USB host mode interrupt management header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __DRV_USBH_INT_H +#define __DRV_USBH_INT_H + +#include "drv_usb_host.h" + +typedef struct _usbh_int_cb +{ + uint8_t (*SOF) (usb_core_driver *pudev); +} usbh_int_cb; + +extern usbh_int_cb *usbh_int_fop; + +uint32_t usbh_isr (usb_core_driver *pudev); + +#endif /* __DRV_USBH_INT_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_ch9_std.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_ch9_std.h new file mode 100644 index 00000000..0029b7fc --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_ch9_std.h @@ -0,0 +1,250 @@ +/*! + \file usb_ch9_std.h + \brief USB 2.0 standard defines + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USB_CH9_STD_H +#define __USB_CH9_STD_H + +#include "usb_conf.h" + +#define USB_DEV_QUALIFIER_DESC_LEN 0x0AU /*!< USB device qualifier descriptor length */ +#define USB_DEV_DESC_LEN 0x12U /*!< USB device descriptor length */ +#define USB_CFG_DESC_LEN 0x09U /*!< USB configuration descriptor length */ +#define USB_ITF_DESC_LEN 0x09U /*!< USB interface descriptor length */ +#define USB_EP_DESC_LEN 0x07U /*!< USB endpoint descriptor length */ +#define USB_OTG_DESC_LEN 0x03U /*!< USB device OTG descriptor length */ +#define USB_ITF_ASSOCIATION_DESC_LEN 0x08U /*!< USB interface association descriptor length */ + +#define USB_SETUP_PACKET_LEN 0x08U /*!< USB setup packet length */ + +/* bit 7 of bmRequestType: data phase transfer direction */ +#define USB_TRX_MASK 0x80U /*!< USB transfer direction mask */ +#define USB_TRX_OUT 0x00U /*!< USB transfer OUT direction */ +#define USB_TRX_IN 0x80U /*!< USB transfer IN direction */ + +/* bit 6..5 of bmRequestType: request type */ +#define USB_REQTYPE_STRD 0x00U /*!< USB standard request */ +#define USB_REQTYPE_CLASS 0x20U /*!< USB class request */ +#define USB_REQTYPE_VENDOR 0x40U /*!< USB vendor request */ +#define USB_REQTYPE_MASK 0x60U /*!< USB request mask */ + +#define USBD_BUS_POWERED 0x00U /*!< USB bus power supply */ +#define USBD_SELF_POWERED 0x01U /*!< USB self power supply */ + +#define USB_STATUS_REMOTE_WAKEUP 2U /*!< USB is in remote wakeup status */ +#define USB_STATUS_SELF_POWERED 1U /*!< USB is in self powered status */ + +/* bit 4..0 of bmRequestType: recipient type */ +enum _usb_recp_type { + USB_RECPTYPE_DEV = 0x0U, /*!< USB device request type */ + USB_RECPTYPE_ITF = 0x1U, /*!< USB interface request type */ + USB_RECPTYPE_EP = 0x2U, /*!< USB endpoint request type */ + USB_RECPTYPE_MASK = 0x3U /*!< USB request type mask */ +}; + +/* bRequest value */ +enum _usb_request { + USB_GET_STATUS = 0x0U, /*!< USB get status request */ + USB_CLEAR_FEATURE = 0x1U, /*!< USB clear feature request */ + USB_RESERVED2 = 0x2U, + USB_SET_FEATURE = 0x3U, /*!< USB set feature request */ + USB_RESERVED4 = 0x4U, + USB_SET_ADDRESS = 0x5U, /*!< USB set address request */ + USB_GET_DESCRIPTOR = 0x6U, /*!< USB get descriptor request */ + USB_SET_DESCRIPTOR = 0x7U, /*!< USB set descriptor request */ + USB_GET_CONFIGURATION = 0x8U, /*!< USB get configuration request */ + USB_SET_CONFIGURATION = 0x9U, /*!< USB set configuration request */ + USB_GET_INTERFACE = 0xAU, /*!< USB get interface request */ + USB_SET_INTERFACE = 0xBU, /*!< USB set interface request */ + USB_SYNCH_FRAME = 0xCU /*!< USB synchronize frame request */ +}; + +/* descriptor types of USB specifications */ +enum _usb_desctype { + USB_DESCTYPE_DEV = 0x1U, /*!< USB device descriptor type */ + USB_DESCTYPE_CONFIG = 0x2U, /*!< USB configuration descriptor type */ + USB_DESCTYPE_STR = 0x3U, /*!< USB string descriptor type */ + USB_DESCTYPE_ITF = 0x4U, /*!< USB interface descriptor type */ + USB_DESCTYPE_EP = 0x5U, /*!< USB endpoint descriptor type */ + USB_DESCTYPE_DEV_QUALIFIER = 0x6U, /*!< USB device qualtfier descriptor type */ + USB_DESCTYPE_OTHER_SPD_CONFIG = 0x7U, /*!< USB other speed configuration descriptor type */ + USB_DESCTYPE_ITF_POWER = 0x8U, /*!< USB interface power descriptor type */ + USB_DESCTYPE_ITF_ASSOCIATION = 0xBU, /*!< USB interface association descriptor type */ + USB_DESCTYPE_BOS = 0xFU /*!< USB BOS descriptor type */ +}; + +/* USB Endpoint Descriptor bmAttributes bit definitions */ +/* bits 1..0 : transfer type */ +enum _usbx_type { + USB_EP_ATTR_CTL = 0x0U, /*!< USB control transfer type */ + USB_EP_ATTR_ISO = 0x1U, /*!< USB Isochronous transfer type */ + USB_EP_ATTR_BULK = 0x2U, /*!< USB Bulk transfer type */ + USB_EP_ATTR_INT = 0x3U /*!< USB Interrupt transfer type */ +}; + +/* bits 3..2 : Sync type (only if ISOCHRONOUS) */ +#define USB_EP_ATTR_NOSYNC 0x00 /* No Synchronization */ +#define USB_EP_ATTR_ASYNC 0x04 /* Asynchronous */ +#define USB_EP_ATTR_ADAPTIVE 0x08 /* Adaptive */ +#define USB_EP_ATTR_SYNC 0x0C /* Synchronous */ +#define USB_EP_ATTR_SYNCTYPE 0x0C /* Synchronous type */ + +/* bits 5..4 : usage type (only if ISOCHRONOUS) */ +#define USB_EP_ATTR_DATA 0x00 /* Data endpoint */ +#define USB_EP_ATTR_FEEDBACK 0x10 /* Feedback endpoint */ +#define USB_EP_ATTR_IMPLICIT_FEEDBACK_DATA 0x20 /* Implicit feedback Data endpoint */ +#define USB_EP_ATTR_USAGETYPE 0x30 /* Usage type */ + +#define FEATURE_SELECTOR_EP 0x00 /* USB endpoint feature selector */ +#define FEATURE_SELECTOR_DEV 0x01 /* USB device feature selector */ + +#define BYTE_SWAP(addr) (((uint16_t)(*((uint8_t *)(addr)))) + \ + (uint16_t)(((uint16_t)(*(((uint8_t *)(addr)) + 1U))) << 8U)) + +#define BYTE_LOW(x) ((uint8_t)((x) & 0x00FFU)) +#define BYTE_HIGH(x) ((uint8_t)(((x) & 0xFF00U) >> 8U)) + +#define USB_MIN(a, b) (((a) < (b)) ? (a) : (b)) + +#define USB_DEFAULT_CONFIG 0U + +/* USB classes */ +#define USB_CLASS_HID 0x03U /*!< USB HID class */ +#define USB_CLASS_MSC 0x08U /*!< USB MSC class */ + +/* use the following values when USB host need to get descriptor */ +#define USBH_DESC(x) (((x)<< 8U) & 0xFF00U) + +/* as per usb specs 9.2.6.4 :standard request with data request timeout: 5sec + standard request with no data stage timeout : 50ms */ +#define DATA_STAGE_TIMEOUT 5000U /*!< USB data stage timeout*/ +#define NODATA_STAGE_TIMEOUT 50U /*!< USB no data stage timeout*/ + +#pragma pack(1) + +/* USB standard device request structure */ +typedef struct _usb_req { + uint8_t bmRequestType; /*!< type of request */ + uint8_t bRequest; /*!< request of setup packet */ + uint16_t wValue; /*!< value of setup packet */ + uint16_t wIndex; /*!< index of setup packet */ + uint16_t wLength; /*!< length of setup packet */ +} usb_req; + +/* USB setup packet define */ +typedef union _usb_setup { + uint8_t data[8]; + + usb_req req; +} usb_setup; + +/* USB descriptor defines */ + +typedef struct _usb_desc_header { + uint8_t bLength; /*!< size of the descriptor */ + uint8_t bDescriptorType; /*!< type of the descriptor */ +} usb_desc_header; + +typedef struct _usb_desc_dev { + usb_desc_header header; /*!< descriptor header, including type and size */ + + uint16_t bcdUSB; /*!< BCD of the supported USB specification */ + uint8_t bDeviceClass; /*!< USB device class */ + uint8_t bDeviceSubClass; /*!< USB device subclass */ + uint8_t bDeviceProtocol; /*!< USB device protocol */ + uint8_t bMaxPacketSize0; /*!< size of the control (address 0) endpoint's bank in bytes */ + uint16_t idVendor; /*!< vendor ID for the USB product */ + uint16_t idProduct; /*!< unique product ID for the USB product */ + uint16_t bcdDevice; /*!< product release (version) number */ + uint8_t iManufacturer; /*!< string index for the manufacturer's name */ + uint8_t iProduct; /*!< string index for the product name/details */ + uint8_t iSerialNumber; /*!< string index for the product's globally unique hexadecimal serial number */ + uint8_t bNumberConfigurations; /*!< total number of configurations supported by the device */ +} usb_desc_dev; + +typedef struct _usb_desc_config { + usb_desc_header header; /*!< descriptor header, including type and size */ + + uint16_t wTotalLength; /*!< size of the configuration descriptor header,and all sub descriptors inside the configuration */ + uint8_t bNumInterfaces; /*!< total number of interfaces in the configuration */ + uint8_t bConfigurationValue; /*!< configuration index of the current configuration */ + uint8_t iConfiguration; /*!< index of a string descriptor describing the configuration */ + uint8_t bmAttributes; /*!< configuration attributes */ + uint8_t bMaxPower; /*!< maximum power consumption of the device while in the current configuration */ +} usb_desc_config; + +typedef struct _usb_desc_itf { + usb_desc_header header; /*!< descriptor header, including type and size */ + + uint8_t bInterfaceNumber; /*!< index of the interface in the current configuration */ + uint8_t bAlternateSetting; /*!< alternate setting for the interface number */ + uint8_t bNumEndpoints; /*!< total number of endpoints in the interface */ + uint8_t bInterfaceClass; /*!< interface class ID */ + uint8_t bInterfaceSubClass; /*!< interface subclass ID */ + uint8_t bInterfaceProtocol; /*!< interface protocol ID */ + uint8_t iInterface; /*!< index of the string descriptor describing the interface */ +} usb_desc_itf; + +typedef struct _usb_desc_itf_association { + usb_desc_header header; /*!< descriptor header, including type and size */ + + uint8_t bFirstInterface; /*!< Interface number of the first interface that is associated with this function */ + uint8_t bInterfaceCount; /*!< Number of contiguous interfaces that are associated with this function */ + uint8_t bFunctoinClass; /*!< Class code */ + uint8_t bFunctionSubClass; /*!< Subclass code */ + uint8_t bFunctionProtocol; /*!< Protocol */ + uint8_t iFunction; /*!< Index of string descriptor describing this function */ +} usb_desc_itf_association; + +typedef struct _usb_desc_ep { + usb_desc_header header; /*!< descriptor header, including type and size. */ + + uint8_t bEndpointAddress; /*!< logical address of the endpoint */ + uint8_t bmAttributes; /*!< endpoint attributes */ + uint16_t wMaxPacketSize; /*!< size of the endpoint bank, in bytes */ + + uint8_t bInterval; /*!< polling interval in milliseconds for the endpoint if it is an INTERRUPT or ISOCHRONOUS type */ +#ifdef AUDIO_ENDPOINT + uint8_t bRefresh; /*!< reset to 0 */ + uint8_t bSynchAddress; /*!< reset to 0 */ +#endif +} usb_desc_ep; + +typedef struct _usb_desc_LANGID { + usb_desc_header header; /*!< descriptor header, including type and size. */ + uint16_t wLANGID; /*!< LANGID code */ +} usb_desc_LANGID; + +#pragma pack() + +#endif /* __USB_CH9_STD_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_conf.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_conf.h new file mode 100644 index 00000000..d2d40a82 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usb_conf.h @@ -0,0 +1,101 @@ +#ifndef __USB_CONF_H +#define __USB_CONF_H + +#include +#include "gd32vf103.h" + +//#ifndef USE_USB_FS +//#define USE_USB_HS +//#endif + +#define USE_USB_FS + +#ifdef USE_USB_FS + #define USB_FS_CORE +#endif + +#ifdef USE_USB_HS + #define USB_HS_CORE +#endif + +#ifdef USB_FS_CORE + #define RX_FIFO_FS_SIZE 128 + #define TX0_FIFO_FS_SIZE 64 + #define TX1_FIFO_FS_SIZE 128 + #define TX2_FIFO_FS_SIZE 0 + #define TX3_FIFO_FS_SIZE 0 + #define USB_RX_FIFO_FS_SIZE 128 + #define USB_HTX_NPFIFO_FS_SIZE 96 + #define USB_HTX_PFIFO_FS_SIZE 96 +#endif /* USB_FS_CORE */ + +#ifdef USB_HS_CORE + #define RX_FIFO_HS_SIZE 512 + #define TX0_FIFO_HS_SIZE 128 + #define TX1_FIFO_HS_SIZE 372 + #define TX2_FIFO_HS_SIZE 0 + #define TX3_FIFO_HS_SIZE 0 + #define TX4_FIFO_HS_SIZE 0 + #define TX5_FIFO_HS_SIZE 0 + + #ifdef USE_ULPI_PHY + #define USB_OTG_ULPI_PHY_ENABLED + #endif + + #ifdef USE_EMBEDDED_PHY + #define USB_OTG_EMBEDDED_PHY_ENABLED + #endif + + #define USB_OTG_HS_INTERNAL_DMA_ENABLED + #define USB_OTG_HS_DEDICATED_EP1_ENABLED +#endif /* USB_HS_CORE */ + +#ifndef USB_SOF_OUTPUT +#define USB_SOF_OUTPUT 0 +#endif + +#ifndef USB_LOW_POWER +#define USB_LOW_POWER 0 +#endif + +//#define USE_HOST_MODE +//#define USE_DEVICE_MODE +//#define USE_OTG_MODE + +#ifndef USE_HOST_MODE +#define USE_DEVICE_MODE +#endif + +#ifndef USB_FS_CORE + #ifndef USB_HS_CORE + #error "USB_HS_CORE or USB_FS_CORE should be defined" + #endif +#endif + +#ifndef USE_DEVICE_MODE + #ifndef USE_HOST_MODE + #error "USE_DEVICE_MODE or USE_HOST_MODE should be defined" + #endif +#endif + +#ifndef USE_USB_HS + #ifndef USE_USB_FS + #error "USE_USB_HS or USE_USB_FS should be defined" + #endif +#endif + +/****************** C Compilers dependant keywords ****************************/ +/* In HS mode and when the DMA is used, all variables and data structures dealing + with the DMA during the transaction process should be 4-bytes aligned */ +#ifdef USB_OTG_HS_INTERNAL_DMA_ENABLED + #if defined (__GNUC__) /* GNU Compiler */ + #define __ALIGN_END __attribute__ ((aligned(4))) + #define __ALIGN_BEGIN + #endif /* __GNUC__ */ +#else + #define __ALIGN_BEGIN + #define __ALIGN_END +#endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */ + +#endif /* __USB_CONF_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_conf.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_conf.h new file mode 100644 index 00000000..b133dd47 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_conf.h @@ -0,0 +1,10 @@ +#ifndef __USBD_CONF_H +#define __USBD_CONF_H + +#include "usb_conf.h" + +#define USBD_CFG_MAX_NUM 1 +#define USBD_ITF_MAX_NUM 1 + +#endif /* __USBD_CONF_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_core.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_core.h new file mode 100644 index 00000000..e22ab7c5 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_core.h @@ -0,0 +1,95 @@ +/*! + \file usbd_core.h + \brief USB device mode core functions protype + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBD_CORE_H +#define __USBD_CORE_H + + +#include "drv_usb_core.h" +#include "drv_usb_dev.h" + +typedef enum +{ + USBD_OK = 0, /*!< status OK */ + USBD_BUSY, /*!< status busy */ + USBD_FAIL, /*!< status fail */ +} usbd_status; + +enum _usbd_status { + USBD_DEFAULT = 1, /*!< default status */ + USBD_ADDRESSED = 2, /*!< address send status */ + USBD_CONFIGURED = 3, /*!< configured status */ + USBD_SUSPENDED = 4 /*!< suspended status */ +}; + +/* function declarations */ + +/* device connect */ +void usbd_connect (usb_core_driver *udev); + +/* device disconnect */ +void usbd_disconnect (usb_core_driver *udev); + +/* set USB device address */ +void usbd_addr_set (usb_core_driver *udev, uint8_t addr); + +/* initailizes the USB device-mode stack and load the class driver */ +void usbd_init (usb_core_driver *udev, usb_core_enum core, usb_class_core *class_core); + +/* endpoint initialization */ +uint32_t usbd_ep_setup (usb_core_driver *udev, const usb_desc_ep *ep_desc); + +/* configure the endpoint when it is disabled */ +uint32_t usbd_ep_clear (usb_core_driver *udev, uint8_t ep_addr); + +/* endpoint prepare to receive data */ +uint32_t usbd_ep_recev (usb_core_driver *udev, uint8_t ep_addr, uint8_t *pbuf, uint16_t len); + +/* endpoint prepare to transmit data */ +uint32_t usbd_ep_send (usb_core_driver *udev, uint8_t ep_addr, uint8_t *pbuf, uint16_t len); + +/* set an endpoint to STALL status */ +uint32_t usbd_ep_stall (usb_core_driver *udev, uint8_t ep_addr); + +/* clear endpoint STALLed status */ +uint32_t usbd_ep_stall_clear (usb_core_driver *udev, uint8_t ep_addr); + +/* flush the endpoint FIFOs */ +uint32_t usbd_fifo_flush (usb_core_driver *udev, uint8_t ep_addr); + +/* get the received data length */ +uint16_t usbd_rxcount_get (usb_core_driver *udev, uint8_t ep_num); + +#endif /* __USBD_CORE_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_enum.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_enum.h new file mode 100644 index 00000000..83569adc --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_enum.h @@ -0,0 +1,114 @@ +/*! + \file usbd_enum.h + \brief USB enumeration definitions + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBD_ENUM_H +#define __USBD_ENUM_H + +#include "usbd_core.h" +#include "usbd_conf.h" +#include + +#ifndef NULL + #define NULL 0U +#endif + +typedef enum _usb_reqsta { + REQ_SUPP = 0x0U, /* request support */ + REQ_NOTSUPP = 0x1U /* request not support */ +} usb_reqsta; + +/* string descriptor index */ +enum _str_index +{ + STR_IDX_LANGID = 0x0U, /* language ID string index */ + STR_IDX_MFC = 0x1U, /* manufacturer string index */ + STR_IDX_PRODUCT = 0x2U, /* product string index */ + STR_IDX_SERIAL = 0x3U, /* serial string index */ + STR_IDX_CONFIG = 0x4U, /* configuration string index */ + STR_IDX_ITF = 0x5U, /* interface string index */ + STR_IDX_MAX = 0x6U /* string maximum index */ +}; + +typedef enum _usb_pwrsta { + USB_PWRSTA_SELF_POWERED = 0x1U, /* USB is in self powered status */ + USB_PWRSTA_REMOTE_WAKEUP = 0x2U, /* USB is in remote wakeup status */ +} usb_pwrsta; + +typedef enum _usb_feature +{ + USB_FEATURE_EP_HALT = 0x0U, /* USB has endpoint halt feature */ + USB_FEATURE_REMOTE_WAKEUP = 0x1U, /* USB has endpoint remote wakeup feature */ + USB_FEATURE_TEST_MODE = 0x2U /* USB has endpoint test mode feature */ +} usb_feature; + +#define ENG_LANGID 0x0409U /* english language ID */ +#define CHN_LANGID 0x0804U /* chinese language ID */ + +/* USB device exported macros */ +#define CTL_EP(ep) (((ep) == 0x00U) || ((ep) == 0x80U)) + +#define WIDE_STRING(string) _WIDE_STRING(string) +#define _WIDE_STRING(string) L##string + +#define USBD_STRING_DESC(string) \ + (void *)&(const struct { \ + uint8_t _len; \ + uint8_t _type; \ + wchar_t _data[sizeof(string)]; \ + }) { \ + sizeof(WIDE_STRING(string)) + 2U - 2U, \ + USB_DESCTYPE_STR, \ + WIDE_STRING(string) \ + } + +/* function declarations */ + +/* handle USB standard device request */ +usb_reqsta usbd_standard_request (usb_core_driver *udev, usb_req *req); + +/* handle USB device class request */ +usb_reqsta usbd_class_request (usb_core_driver *udev, usb_req *req); + +/* handle USB vendor request */ +usb_reqsta usbd_vendor_request (usb_core_driver *udev, usb_req *req); + +/* handle USB enumeration error */ +void usbd_enum_error (usb_core_driver *udev, usb_req *req); + +/* convert hex 32bits value into unicode char */ +void int_to_unicode (uint32_t value, uint8_t *pbuf, uint8_t len); + +#endif /* __USBD_ENUM_H */ + + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_transc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_transc.h new file mode 100644 index 00000000..aabfd732 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbd_transc.h @@ -0,0 +1,64 @@ +/*! + \file usbd_transc.h + \brief USB transaction core functions prototype + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBD_TRANSC_H +#define __USBD_TRANSC_H + +#include "usbd_core.h" + +/* function declarations */ + +/* USB send data in the control transaction */ +usbd_status usbd_ctl_send (usb_core_driver *udev); + +/* USB receive data in control transaction */ +usbd_status usbd_ctl_recev (usb_core_driver *udev); + +/* USB send control transaction status */ +usbd_status usbd_ctl_status_send (usb_core_driver *udev); + +/* USB control receive status */ +usbd_status usbd_ctl_status_recev (usb_core_driver *udev); + +/* USB setup stage processing */ +uint8_t usbd_setup_transc (usb_core_driver *udev); + +/* data out stage processing */ +uint8_t usbd_out_transc (usb_core_driver *udev, uint8_t ep_num)__attribute__((optimize("O0"))); + +/* data in stage processing */ +uint8_t usbd_in_transc (usb_core_driver *udev, uint8_t ep_num)__attribute__((optimize("O0"))); + +#endif /* __USBD_TRANSC_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_conf.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_conf.h new file mode 100644 index 00000000..4aba05dc --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_conf.h @@ -0,0 +1,9 @@ +#ifndef __USBH_CONF_H +#define __USBH_CONF_H + +#define USBH_MAX_EP_NUM 2 +#define USBH_MAX_INTERFACES_NUM 2 +#define USBH_MSC_MPS_SIZE 0x200 + +#endif /* __USBH_CONF_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_core.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_core.h new file mode 100644 index 00000000..32852534 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_core.h @@ -0,0 +1,219 @@ +/*! + \file usbh_core.h + \brief USB host core state machine header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBH_CORE_H +#define __USBH_CORE_H + +#include "usbh_conf.h" +#include "drv_usb_host.h" + +#define MSC_CLASS 0x08U +#define HID_CLASS 0x03U +#define MSC_PROTOCOL 0x50U +#define CBI_PROTOCOL 0x01U + +#define USBH_MAX_ERROR_COUNT 3U + +#define USBH_DEV_ADDR_DEFAULT 0U +#define USBH_DEV_ADDR 1U + +typedef enum +{ + USBH_OK = 0U, + USBH_BUSY, + USBH_FAIL, + USBH_NOT_SUPPORTED, + USBH_UNRECOVERED_ERROR, + USBH_SPEED_UNKNOWN_ERROR, + USBH_APPLY_DEINIT +} usbh_status; + +/* USB host global operation state */ +typedef enum +{ + HOST_DEFAULT = 0U, + HOST_DETECT_DEV_SPEED, + HOST_DEV_ATTACHED, + HOST_DEV_DETACHED, + HOST_ENUM, + HOST_CLASS_ENUM, + HOST_CLASS_HANDLER, + HOST_USER_INPUT, + HOST_SUSPENDED, + HOST_ERROR +} usb_host_state; + +/* USB host enumeration state */ +typedef enum +{ + ENUM_DEFAULT = 0U, + ENUM_GET_DEV_DESC, + ENUM_SET_ADDR, + ENUM_GET_CFG_DESC, + ENUM_GET_CFG_DESC_SET, + ENUM_GET_STR_DESC, + ENUM_SET_CONFIGURATION, + ENUM_DEV_CONFIGURED +} usbh_enum_state; + +/* USB host control transfer state */ +typedef enum +{ + CTL_IDLE = 0U, + CTL_SETUP, + CTL_DATA_IN, + CTL_DATA_OUT, + CTL_STATUS_IN, + CTL_STATUS_OUT, + CTL_ERROR, + CTL_FINISH +} usbh_ctl_state; + +/* user action state */ +typedef enum +{ + USBH_USER_NO_RESP = 0U, + USBH_USER_RESP_OK = 1U, +} usbh_user_status; + +/* control transfer information */ +typedef struct _usbh_control +{ + uint8_t pipe_in_num; + uint8_t pipe_out_num; + uint8_t max_len; + uint8_t error_count; + + uint8_t *buf; + uint16_t ctl_len; + uint16_t timer; + + usb_setup setup; + usbh_ctl_state ctl_state; +} usbh_control; + +/* USB device property */ +typedef struct +{ + uint8_t addr; + uint32_t speed; + + usb_desc_dev dev_desc; + usb_desc_config cfg_desc; + usb_desc_itf itf_desc[USBH_MAX_INTERFACES_NUM]; + usb_desc_ep ep_desc[USBH_MAX_INTERFACES_NUM][USBH_MAX_EP_NUM]; +} usb_dev_prop; + +/** + * @brief Device class callbacks + */ +typedef struct +{ + usbh_status (*class_init) (usb_core_driver *pudev, void *phost); + void (*class_deinit) (usb_core_driver *pudev, void *phost); + usbh_status (*class_requests) (usb_core_driver *pudev, void *phost); + usbh_status (*class_machine) (usb_core_driver *pudev, void *phost); +} usbh_class_cb; + +/** + * @brief User callbacks + */ +typedef struct +{ + void (*dev_init) (void); + void (*dev_deinit) (void); + void (*dev_attach) (void); + void (*dev_reset) (void); + void (*dev_detach) (void); + void (*dev_over_currented) (void); + void (*dev_speed_detected) (uint32_t dev_speed); + void (*dev_devdesc_assigned) (void *dev_desc); + void (*dev_address_set) (void); + + void (*dev_cfgdesc_assigned) (usb_desc_config *cfg_desc, + usb_desc_itf *itf_desc, + usb_desc_ep *ep_desc); + + void (*dev_mfc_str) (void *mfc_str); + void (*dev_prod_str) (void *prod_str); + void (*dev_seral_str) (void *serial_str); + void (*dev_enumerated) (void); + usbh_user_status (*dev_user_input) (void); + int (*dev_user_app) (void); + void (*dev_not_supported) (void); + void (*dev_error) (void); +} usbh_user_cb; + +/** + * @brief Host information + */ +typedef struct +{ + usb_host_state cur_state; /*!< host state machine value */ + usb_host_state backup_state; /*!< backup of previous state machine value */ + usbh_enum_state enum_state; /*!< enumeration state machine */ + usbh_control control; /*!< USB host control state machine */ + usb_dev_prop dev_prop; /*!< USB device properity */ + + usbh_class_cb *class_cb; /*!< USB class callback */ + usbh_user_cb *usr_cb; /*!< USB user callback */ +} usbh_host; + + +/* USB host stack initializations */ +void usbh_init (usb_core_driver *pudev, usb_core_enum core, usbh_host *puhost); + +/* de-initialize USB host */ +usbh_status usbh_deinit (usb_core_driver *pudev, usbh_host *puhost); + +/* USB host core main state machine process */ +void usbh_core_task (usb_core_driver *pudev, usbh_host *puhost); + +/* handle the error on USB host side */ +void usbh_error_handler (usbh_host *puhost, usbh_status ErrType); + +/* get USB URB state */ +static inline usb_urb_state usbh_urbstate_get (usb_core_driver *pudev, uint8_t pp_num) +{ + return pudev->host.pipe[pp_num].urb_state; +} + +/* get USB transfer data count */ +static inline uint32_t usbh_xfercount_get (usb_core_driver *pudev, uint8_t pp_num) +{ + return pudev->host.backup_xfercount[pp_num]; +} + +#endif /* __USBH_CORE_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_enum.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_enum.h new file mode 100644 index 00000000..b0a617b4 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_enum.h @@ -0,0 +1,78 @@ +/*! + \file usbh_enum.h + \brief USB host mode USB enumeration header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBH_ENUM_H +#define __USBH_ENUM_H + +#include "usb_conf.h" +#include "usbh_core.h" + +/* get the next descriptor header */ +usb_desc_header *usbh_nextdesc_get (uint8_t *pbuf, uint16_t *ptr); + +/* configure USB control status parameters */ +void usbh_ctlstate_config (usbh_host *puhost, uint8_t *buf, uint16_t len); + +/* get device descriptor from the USB device */ +usbh_status usbh_devdesc_get (usb_core_driver *pudev, usbh_host *puhost, uint8_t len); + +/* get configuration descriptor from the USB device */ +usbh_status usbh_cfgdesc_get (usb_core_driver *pudev, usbh_host *puhost, uint16_t len); + +/* get string descriptor from the USB device */ +usbh_status usbh_strdesc_get (usb_core_driver *pudev, + usbh_host *puhost, + uint8_t str_index, + uint8_t *buf, + uint16_t len); + +/* set the configuration value to the connected device */ +usbh_status usbh_setcfg (usb_core_driver *pudev, usbh_host *puhost, uint16_t config); + +/* set the address to the connected device */ +usbh_status usbh_setaddress (usb_core_driver *pudev, usbh_host *puhost, uint8_t dev_addr); + +/* clear or disable a specific feature */ +usbh_status usbh_clrfeature (usb_core_driver *pudev, + usbh_host *puhost, + uint8_t ep_num, + uint8_t pp_num); + +/* set the interface value to the connected device */ +usbh_status usbh_setinterface (usb_core_driver *pudev, + usbh_host *puhost, + uint8_t ep_num, + uint8_t alter_setting); + +#endif /* __USBH_ENUM_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_pipe.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_pipe.h new file mode 100644 index 00000000..bf40bfcc --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_pipe.h @@ -0,0 +1,70 @@ +/*! + \file usbh_pipe.h + \brief USB host mode pipe header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBH_PIPE_H +#define __USBH_PIPE_H + +#include "usbh_core.h" + +#define HC_MAX 8U + +#define HC_OK 0x0000U +#define HC_USED 0x8000U +#define HC_ERROR 0xFFFFU +#define HC_USED_MASK 0x7FFFU + +/* allocate a new pipe */ +uint8_t usbh_pipe_allocate (usb_core_driver *pudev, uint8_t ep_addr); + +/* delete all USB host pipe */ +uint8_t usbh_pipe_delete (usb_core_driver *pudev); + +/* free a pipe */ +uint8_t usbh_pipe_free (usb_core_driver *pudev, uint8_t pp_num); + +/* create a pipe */ +uint8_t usbh_pipe_create (usb_core_driver *pudev, + usb_dev_prop *udev, + uint8_t pp_num, + uint8_t ep_type, + uint16_t ep_mpl); + +/* modify a pipe */ +uint8_t usbh_pipe_update (usb_core_driver *pudev, + uint8_t pp_num, + uint8_t dev_addr, + uint32_t dev_speed, + uint16_t ep_mpl); + +#endif /* __USBH_PIPE_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_transc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_transc.h new file mode 100644 index 00000000..ff1eb7ff --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/Usb/usbh_transc.h @@ -0,0 +1,54 @@ +/*! + \file usbh_transc.h + \brief USB host mode transactions header file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef __USBH_TRANSC_H +#define __USBH_TRANSC_H + +#include "usb_conf.h" +#include "usbh_core.h" + +/* send the setup packet to the USB device */ +usbh_status usbh_ctlsetup_send (usb_core_driver *pudev, uint8_t *buf, uint8_t pp_num); + +/* send a data packet to the USB device */ +usbh_status usbh_data_send (usb_core_driver *pudev, uint8_t *buf, uint8_t pp_num, uint16_t len); + +/* receive a data packet from the USB device */ +usbh_status usbh_data_recev (usb_core_driver *pudev, uint8_t *buf, uint8_t pp_num, uint16_t len); + +/* USB control transfer handler */ +usbh_status usbh_ctl_handler (usb_core_driver *pudev, usbh_host *puhost); + +#endif /* __USBH_TRANSC_H */ + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103.h new file mode 100644 index 00000000..73941a2a --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103.h @@ -0,0 +1,390 @@ +/****************************************************************************** + * @file gd32vf103.h + * @brief NMSIS Core Peripheral Access Layer Header File for GD32VF103 series + * + * @version V1.00 + * @date 4. Jan 2020 + ******************************************************************************/ +/* + * Copyright (c) 2019 Nuclei Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +#ifndef __GD32VF103_H__ +#define __GD32VF103_H__ + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** @addtogroup gd32 + * @{ + */ + + +/** @addtogroup gd32vf103 + * @{ + */ + + +/** @addtogroup Configuration_of_NMSIS + * @{ + */ + + + + +/* =========================================================================================================================== */ +/* ================ Interrupt Number Definition ================ */ +/* =========================================================================================================================== */ + +typedef enum IRQn +{ +/* ======================================= Nuclei Core Specific Interrupt Numbers ======================================== */ + + Reserved0_IRQn = 0, /*!< Internal reserved */ + Reserved1_IRQn = 1, /*!< Internal reserved */ + Reserved2_IRQn = 2, /*!< Internal reserved */ + SysTimerSW_IRQn = 3, /*!< System Timer SW interrupt */ + Reserved3_IRQn = 4, /*!< Internal reserved */ + Reserved4_IRQn = 5, /*!< Internal reserved */ + Reserved5_IRQn = 6, /*!< Internal reserved */ + SysTimer_IRQn = 7, /*!< System Timer Interrupt */ + Reserved6_IRQn = 8, /*!< Internal reserved */ + Reserved7_IRQn = 9, /*!< Internal reserved */ + Reserved8_IRQn = 10, /*!< Internal reserved */ + Reserved9_IRQn = 11, /*!< Internal reserved */ + Reserved10_IRQn = 12, /*!< Internal reserved */ + Reserved11_IRQn = 13, /*!< Internal reserved */ + Reserved12_IRQn = 14, /*!< Internal reserved */ + Reserved13_IRQn = 15, /*!< Internal reserved */ + Reserved14_IRQn = 16, /*!< Internal reserved */ + BusError_IRQn = 17, /*!< Bus Error interrupt */ + PerfMon_IRQn = 18, /*!< Performance Monitor */ + +/* =========================================== GD32VF103 Specific Interrupt Numbers ========================================= */ +/* ToDo: add here your device specific external interrupt numbers. 19~1023 is reserved number for user. Maxmum interrupt supported + could get from clicinfo.NUM_INTERRUPT. According the interrupt handlers defined in startup_Device.s + eg.: Interrupt for Timer#1 TIM1_IRQHandler -> TIM1_IRQn */ + /* interruput numbers */ + WWDGT_IRQn = 19, /*!< window watchDog timer interrupt */ + LVD_IRQn = 20, /*!< LVD through EXTI line detect interrupt */ + TAMPER_IRQn = 21, /*!< tamper through EXTI line detect */ + RTC_IRQn = 22, /*!< RTC alarm interrupt */ + FMC_IRQn = 23, /*!< FMC interrupt */ + RCU_CTC_IRQn = 24, /*!< RCU and CTC interrupt */ + EXTI0_IRQn = 25, /*!< EXTI line 0 interrupts */ + EXTI1_IRQn = 26, /*!< EXTI line 1 interrupts */ + EXTI2_IRQn = 27, /*!< EXTI line 2 interrupts */ + EXTI3_IRQn = 28, /*!< EXTI line 3 interrupts */ + EXTI4_IRQn = 29, /*!< EXTI line 4 interrupts */ + DMA0_Channel0_IRQn = 30, /*!< DMA0 channel0 interrupt */ + DMA0_Channel1_IRQn = 31, /*!< DMA0 channel1 interrupt */ + DMA0_Channel2_IRQn = 32, /*!< DMA0 channel2 interrupt */ + DMA0_Channel3_IRQn = 33, /*!< DMA0 channel3 interrupt */ + DMA0_Channel4_IRQn = 34, /*!< DMA0 channel4 interrupt */ + DMA0_Channel5_IRQn = 35, /*!< DMA0 channel5 interrupt */ + DMA0_Channel6_IRQn = 36, /*!< DMA0 channel6 interrupt */ + ADC0_1_IRQn = 37, /*!< ADC0 and ADC1 interrupt */ + CAN0_TX_IRQn = 38, /*!< CAN0 TX interrupts */ + CAN0_RX0_IRQn = 39, /*!< CAN0 RX0 interrupts */ + CAN0_RX1_IRQn = 40, /*!< CAN0 RX1 interrupts */ + CAN0_EWMC_IRQn = 41, /*!< CAN0 EWMC interrupts */ + EXTI5_9_IRQn = 42, /*!< EXTI[9:5] interrupts */ + TIMER0_BRK_IRQn = 43, /*!< TIMER0 break interrupts */ + TIMER0_UP_IRQn = 44, /*!< TIMER0 update interrupts */ + TIMER0_TRG_CMT_IRQn = 45, /*!< TIMER0 trigger and commutation interrupts */ + TIMER0_Channel_IRQn = 46, /*!< TIMER0 channel capture compare interrupts */ + TIMER1_IRQn = 47, /*!< TIMER1 interrupt */ + TIMER2_IRQn = 48, /*!< TIMER2 interrupt */ + TIMER3_IRQn = 49, /*!< TIMER3 interrupts */ + I2C0_EV_IRQn = 50, /*!< I2C0 event interrupt */ + I2C0_ER_IRQn = 51, /*!< I2C0 error interrupt */ + I2C1_EV_IRQn = 52, /*!< I2C1 event interrupt */ + I2C1_ER_IRQn = 53, /*!< I2C1 error interrupt */ + SPI0_IRQn = 54, /*!< SPI0 interrupt */ + SPI1_IRQn = 55, /*!< SPI1 interrupt */ + USART0_IRQn = 56, /*!< USART0 interrupt */ + USART1_IRQn = 57, /*!< USART1 interrupt */ + USART2_IRQn = 58, /*!< USART2 interrupt */ + EXTI10_15_IRQn = 59, /*!< EXTI[15:10] interrupts */ + RTC_ALARM_IRQn = 60, /*!< RTC alarm interrupt EXTI */ + USBFS_WKUP_IRQn = 61, /*!< USBFS wakeup interrupt */ + + EXMC_IRQn = 67, /*!< EXMC global interrupt */ + + TIMER4_IRQn = 69, /*!< TIMER4 global interrupt */ + SPI2_IRQn = 70, /*!< SPI2 global interrupt */ + UART3_IRQn = 71, /*!< UART3 global interrupt */ + UART4_IRQn = 72, /*!< UART4 global interrupt */ + TIMER5_IRQn = 73, /*!< TIMER5 global interrupt */ + TIMER6_IRQn = 74, /*!< TIMER6 global interrupt */ + DMA1_Channel0_IRQn = 75, /*!< DMA1 channel0 global interrupt */ + DMA1_Channel1_IRQn = 76, /*!< DMA1 channel1 global interrupt */ + DMA1_Channel2_IRQn = 77, /*!< DMA1 channel2 global interrupt */ + DMA1_Channel3_IRQn = 78, /*!< DMA1 channel3 global interrupt */ + DMA1_Channel4_IRQn = 79, /*!< DMA1 channel3 global interrupt */ + + CAN1_TX_IRQn = 82, /*!< CAN1 TX interrupt */ + CAN1_RX0_IRQn = 83, /*!< CAN1 RX0 interrupt */ + CAN1_RX1_IRQn = 84, /*!< CAN1 RX1 interrupt */ + CAN1_EWMC_IRQn = 85, /*!< CAN1 EWMC interrupt */ + USBFS_IRQn = 86, /*!< USBFS global interrupt */ + + SOC_INT_MAX, + +} IRQn_Type; + +/* =========================================================================================================================== */ +/* ================ Exception Code Definition ================ */ +/* =========================================================================================================================== */ + +typedef enum EXCn { +/* ======================================= Nuclei N/NX Specific Exception Code ======================================== */ + InsUnalign_EXCn = 0, /*!< Instruction address misaligned */ + InsAccFault_EXCn = 1, /*!< Instruction access fault */ + IlleIns_EXCn = 2, /*!< Illegal instruction */ + Break_EXCn = 3, /*!< Beakpoint */ + LdAddrUnalign_EXCn = 4, /*!< Load address misaligned */ + LdFault_EXCn = 5, /*!< Load access fault */ + StAddrUnalign_EXCn = 6, /*!< Store or AMO address misaligned */ + StAccessFault_EXCn = 7, /*!< Store or AMO access fault */ + UmodeEcall_EXCn = 8, /*!< Environment call from User mode */ + MmodeEcall_EXCn = 11, /*!< Environment call from Machine mode */ + NMI_EXCn = 0xfff, /*!< NMI interrupt*/ +} EXCn_Type; + +/* =========================================================================================================================== */ +/* ================ Processor and Core Peripheral Section ================ */ +/* =========================================================================================================================== */ + +/* ToDo: set the defines according your Device */ +/* ToDo: define the correct core revision */ +#define __NUCLEI_N_REV 0x0100 /*!< Core Revision r1p0 */ + +/* ToDo: define the correct core features for the nuclei_soc */ +#define __ECLIC_PRESENT 1 /*!< Set to 1 if ECLIC is present */ +#define __ECLIC_BASEADDR 0xD2000000UL /*!< Set to ECLIC baseaddr of your device */ + +#define __ECLIC_INTCTLBITS 4 /*!< Set to 1 - 8, the number of hardware bits are actually implemented in the clicintctl registers. */ +#define __ECLIC_INTNUM 86 /*!< Set to 1 - 1005, the external interrupt number of ECLIC Unit */ +#define __SYSTIMER_PRESENT 1 /*!< Set to 1 if System Timer is present */ +#define __SYSTIMER_BASEADDR 0xD1000000UL /*!< Set to SysTimer baseaddr of your device */ + +/*!< Set to 0, 1, or 2, 0 not present, 1 single floating point unit present, 2 double floating point unit present */ +#define __FPU_PRESENT 0 + +#define __DSP_PRESENT 0 /*!< Set to 1 if DSP is present */ +#define __PMP_PRESENT 1 /*!< Set to 1 if PMP is present */ +#define __PMP_ENTRY_NUM 8 /*!< Set to 8 or 16, the number of PMP entries */ +#define __ICACHE_PRESENT 0 /*!< Set to 1 if I-Cache is present */ +#define __DCACHE_PRESENT 0 /*!< Set to 1 if D-Cache is present */ +#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */ +#define __Vendor_EXCEPTION 0 /*!< Set to 1 if vendor exception hander is present */ + +/** @} */ /* End of group Configuration_of_CMSIS */ + + + +#include /*!< Nuclei N/NX class processor and core peripherals */ +/* ToDo: include your system_nuclei_soc.h file + replace 'Device' with your device name */ +#include "system_gd32vf103.h" /*!< gd32vf103 System */ + + +/* ======================================== Start of section using anonymous unions ======================================== */ +#if defined (__GNUC__) + /* anonymous unions are enabled by default */ +#else + #warning Not supported compiler type +#endif + + +/* system frequency define */ +#define __IRC8M (IRC8M_VALUE) /* internal 8 MHz RC oscillator frequency */ +#define __HXTAL (HXTAL_VALUE) /* high speed crystal oscillator frequency */ +#define __SYS_OSC_CLK (__IRC8M) /* main oscillator frequency */ + +#define __SYSTEM_CLOCK_108M_PLL_HXTAL (uint32_t)(108000000) + + +#define RTC_FREQ LXTAL_VALUE + // The TIMER frequency is just the RTC frequency +#define SOC_TIMER_FREQ ((uint32_t)SystemCoreClock/4) //LXTAL_VALUE units HZ + + +/* enum definitions */ +typedef enum { + DISABLE = 0, + ENABLE = !DISABLE +} EventStatus, ControlStatus; + +// Already defined +// typedef enum { +// FALSE = 0, +// TRUE = !FALSE +// } BOOL; + +typedef enum { + RESET = 0, + SET = 1, + MAX = 0X7FFFFFFF +} FlagStatus; + +typedef enum { + ERROR = 0, + SUCCESS = !ERROR +} ErrStatus; + +/* =========================================================================================================================== */ +/* ================ Device Specific Peripheral Section ================ */ +/* =========================================================================================================================== */ + + +/** @addtogroup Device_Peripheral_peripherals + * @{ + */ + +/**************************************************************************** + * Platform definitions + *****************************************************************************/ + + + + + +/* ToDo: add here your device specific peripheral access structure typedefs + following is an example for Systick Timer*/ + +/* =========================================================================================================================== */ +/* ================ SysTick Timer ================ */ +/* =========================================================================================================================== */ + +/*@}*/ /* end of group nuclei_soc_Peripherals */ + + +/* ========================================= End of section using anonymous unions ========================================= */ +#if defined (__GNUC__) + /* anonymous unions are enabled by default */ +#else + #warning Not supported compiler type +#endif + + +/* =========================================================================================================================== */ +/* ================ Device Specific Peripheral Address Map ================ */ +/* =========================================================================================================================== */ + + +/* ToDo: add here your device peripherals base addresses + following is an example for timer */ +/** @addtogroup Device_Peripheral_peripheralAddr + * @{ + */ +/* main flash and SRAM memory map */ +#define FLASH_BASE ((uint32_t)0x08000000U) /*!< main FLASH base address */ +#define SRAM_BASE ((uint32_t)0x20000000U) /*!< SRAM0 base address */ +#define OB_BASE ((uint32_t)0x1FFFF800U) /*!< OB base address */ +#define DBG_BASE ((uint32_t)0xE0042000U) /*!< DBG base address */ +#define EXMC_BASE ((uint32_t)0xA0000000U) /*!< EXMC register base address */ + +/* peripheral memory map */ +#define APB1_BUS_BASE ((uint32_t)0x40000000U) /*!< apb1 base address */ +#define APB2_BUS_BASE ((uint32_t)0x40010000U) /*!< apb2 base address */ +#define AHB1_BUS_BASE ((uint32_t)0x40018000U) /*!< ahb1 base address */ +#define AHB3_BUS_BASE ((uint32_t)0x60000000U) /*!< ahb3 base address */ + +/* advanced peripheral bus 1 memory map */ +#define TIMER_BASE (APB1_BUS_BASE + 0x00000000U) /*!< TIMER base address */ +#define RTC_BASE (APB1_BUS_BASE + 0x00002800U) /*!< RTC base address */ +#define WWDGT_BASE (APB1_BUS_BASE + 0x00002C00U) /*!< WWDGT base address */ +#define FWDGT_BASE (APB1_BUS_BASE + 0x00003000U) /*!< FWDGT base address */ +#define SPI_BASE (APB1_BUS_BASE + 0x00003800U) /*!< SPI base address */ +#define USART_BASE (APB1_BUS_BASE + 0x00004400U) /*!< USART base address */ +#define I2C_BASE (APB1_BUS_BASE + 0x00005400U) /*!< I2C base address */ +#define CAN_BASE (APB1_BUS_BASE + 0x00006400U) /*!< CAN base address */ +#define BKP_BASE (APB1_BUS_BASE + 0x00006C00U) /*!< BKP base address */ +#define PMU_BASE (APB1_BUS_BASE + 0x00007000U) /*!< PMU base address */ +#define DAC_BASE (APB1_BUS_BASE + 0x00007400U) /*!< DAC base address */ + +/* advanced peripheral bus 2 memory map */ +#define AFIO_BASE (APB2_BUS_BASE + 0x00000000U) /*!< AFIO base address */ +#define EXTI_BASE (APB2_BUS_BASE + 0x00000400U) /*!< EXTI base address */ +#define GPIO_BASE (APB2_BUS_BASE + 0x00000800U) /*!< GPIO base address */ +#define ADC_BASE (APB2_BUS_BASE + 0x00002400U) /*!< ADC base address */ + +/* advanced high performance bus 1 memory map */ +#define DMA_BASE (AHB1_BUS_BASE + 0x00008000U) /*!< DMA base address */ +#define RCU_BASE (AHB1_BUS_BASE + 0x00009000U) /*!< RCU base address */ +#define FMC_BASE (AHB1_BUS_BASE + 0x0000A000U) /*!< FMC base address */ +#define CRC_BASE (AHB1_BUS_BASE + 0x0000B000U) /*!< CRC base address */ +#define USBFS_BASE (AHB1_BUS_BASE + 0x0FFE8000U) /*!< USBFS base address */ + + +/** @} */ /* End of group Device_Peripheral_peripheralAddr */ + + +/* =========================================================================================================================== */ +/* ================ Peripheral declaration ================ */ +/* =========================================================================================================================== */ + + +/* ToDo: add here your device peripherals pointer definitions + following is an example for timer */ +/** @addtogroup Device_Peripheral_declaration + * @{ + */ +/* bit operations */ +#define REG32(addr) (*(volatile uint32_t *)(uint32_t)(addr)) +#define REG16(addr) (*(volatile uint16_t *)(uint32_t)(addr)) +#define REG8(addr) (*(volatile uint8_t *)(uint32_t)(addr)) +#define BIT(x) ((uint32_t)((uint32_t)0x01U<<(x))) +#define BITS(start, end) ((0xFFFFFFFFUL << (start)) & (0xFFFFFFFFUL >> (31U - (uint32_t)(end)))) +#define GET_BITS(regval, start, end) (((regval) & BITS((start),(end))) >> (start)) + +// Interrupt Numbers +#define SOC_ECLIC_NUM_INTERRUPTS 86 +#define SOC_ECLIC_INT_GPIO_BASE 19 + + +// Interrupt Handler Definitions +#define SOC_MTIMER_HANDLER eclic_mtip_handler +#define SOC_SOFTINT_HANDLER eclic_msip_handler + +#define NUM_GPIO 32 + +extern uint32_t get_cpu_freq(void); + +/** + * \brief delay a time in milliseconds + * \param[in] count: count in milliseconds + * \param[out] none + * \retval none + */ +extern void delay_1ms(uint32_t count); + + +/** @} */ /* End of group gd32vf103_soc */ + +/** @} */ /* End of group gd32vf103 */ + +#ifdef __cplusplus +} +#endif + +#endif /* __GD32VF103_SOC_H__ */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_adc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_adc.h new file mode 100644 index 00000000..6282203a --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_adc.h @@ -0,0 +1,399 @@ +/*! + \file gd32vf103_adc.h + \brief definitions for the ADC + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_ADC_H +#define GD32VF103_ADC_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* ADC definitions */ +#define ADC0 ADC_BASE +#define ADC1 (ADC_BASE + 0x400U) + + +/* registers definitions */ +#define ADC_STAT(adcx) REG32((adcx) + 0x00U) /*!< ADC status register */ +#define ADC_CTL0(adcx) REG32((adcx) + 0x04U) /*!< ADC control register 0 */ +#define ADC_CTL1(adcx) REG32((adcx) + 0x08U) /*!< ADC control register 1 */ +#define ADC_SAMPT0(adcx) REG32((adcx) + 0x0CU) /*!< ADC sampling time register 0 */ +#define ADC_SAMPT1(adcx) REG32((adcx) + 0x10U) /*!< ADC sampling time register 1 */ +#define ADC_IOFF0(adcx) REG32((adcx) + 0x14U) /*!< ADC inserted channel data offset register 0 */ +#define ADC_IOFF1(adcx) REG32((adcx) + 0x18U) /*!< ADC inserted channel data offset register 1 */ +#define ADC_IOFF2(adcx) REG32((adcx) + 0x1CU) /*!< ADC inserted channel data offset register 2 */ +#define ADC_IOFF3(adcx) REG32((adcx) + 0x20U) /*!< ADC inserted channel data offset register 3 */ +#define ADC_WDHT(adcx) REG32((adcx) + 0x24U) /*!< ADC watchdog high threshold register */ +#define ADC_WDLT(adcx) REG32((adcx) + 0x28U) /*!< ADC watchdog low threshold register */ +#define ADC_RSQ0(adcx) REG32((adcx) + 0x2CU) /*!< ADC regular sequence register 0 */ +#define ADC_RSQ1(adcx) REG32((adcx) + 0x30U) /*!< ADC regular sequence register 1 */ +#define ADC_RSQ2(adcx) REG32((adcx) + 0x34U) /*!< ADC regular sequence register 2 */ +#define ADC_ISQ(adcx) REG32((adcx) + 0x38U) /*!< ADC inserted sequence register */ +#define ADC_IDATA0(adcx) REG32((adcx) + 0x3CU) /*!< ADC inserted data register 0 */ +#define ADC_IDATA1(adcx) REG32((adcx) + 0x40U) /*!< ADC inserted data register 1 */ +#define ADC_IDATA2(adcx) REG32((adcx) + 0x44U) /*!< ADC inserted data register 2 */ +#define ADC_IDATA3(adcx) REG32((adcx) + 0x48U) /*!< ADC inserted data register 3 */ +#define ADC_RDATA(adcx) REG32((adcx) + 0x4CU) /*!< ADC regular data register */ +#define ADC_OVSCR(adcx) REG32((adcx) + 0x80U) /*!< ADC oversample control register */ + +/* bits definitions */ +/* ADC_STAT */ +#define ADC_STAT_WDE BIT(0) /*!< analog watchdog event flag */ +#define ADC_STAT_EOC BIT(1) /*!< end of conversion */ +#define ADC_STAT_EOIC BIT(2) /*!< inserted channel end of conversion */ +#define ADC_STAT_STIC BIT(3) /*!< inserted channel start flag */ +#define ADC_STAT_STRC BIT(4) /*!< regular channel start flag */ + +/* ADC_CTL0 */ +#define ADC_CTL0_WDCHSEL BITS(0,4) /*!< analog watchdog channel select bits */ +#define ADC_CTL0_EOCIE BIT(5) /*!< interrupt enable for EOC */ +#define ADC_CTL0_WDEIE BIT(6) /*!< analog watchdog interrupt enable */ +#define ADC_CTL0_EOICIE BIT(7) /*!< interrupt enable for inserted channels */ +#define ADC_CTL0_SM BIT(8) /*!< scan mode */ +#define ADC_CTL0_WDSC BIT(9) /*!< when in scan mode, analog watchdog is effective on a single channel */ +#define ADC_CTL0_ICA BIT(10) /*!< automatic inserted group conversion */ +#define ADC_CTL0_DISRC BIT(11) /*!< discontinuous mode on regular channels */ +#define ADC_CTL0_DISIC BIT(12) /*!< discontinuous mode on inserted channels */ +#define ADC_CTL0_DISNUM BITS(13,15) /*!< discontinuous mode channel count */ +#define ADC_CTL0_SYNCM BITS(16,19) /*!< sync mode selection */ +#define ADC_CTL0_IWDEN BIT(22) /*!< analog watchdog enable on inserted channels */ +#define ADC_CTL0_RWDEN BIT(23) /*!< analog watchdog enable on regular channels */ + +/* ADC_CTL1 */ +#define ADC_CTL1_ADCON BIT(0) /*!< ADC converter on */ +#define ADC_CTL1_CTN BIT(1) /*!< continuous conversion */ +#define ADC_CTL1_CLB BIT(2) /*!< ADC calibration */ +#define ADC_CTL1_RSTCLB BIT(3) /*!< reset calibration */ +#define ADC_CTL1_DMA BIT(8) /*!< direct memory access mode */ +#define ADC_CTL1_DAL BIT(11) /*!< data alignment */ +#define ADC_CTL1_ETSIC BITS(12,14) /*!< external trigger select for inserted channel */ +#define ADC_CTL1_ETEIC BIT(15) /*!< external trigger enable for inserted channel */ +#define ADC_CTL1_ETSRC BITS(17,19) /*!< external trigger select for regular channel */ +#define ADC_CTL1_ETERC BIT(20) /*!< external trigger conversion mode for inserted channels */ +#define ADC_CTL1_SWICST BIT(21) /*!< start on inserted channel */ +#define ADC_CTL1_SWRCST BIT(22) /*!< start on regular channel */ +#define ADC_CTL1_TSVREN BIT(23) /*!< channel 16 and 17 enable of ADC0 */ + +/* ADC_SAMPTx x=0..1 */ +#define ADC_SAMPTX_SPTN BITS(0,2) /*!< channel n sample time selection */ + +/* ADC_IOFFx x=0..3 */ +#define ADC_IOFFX_IOFF BITS(0,11) /*!< data offset for inserted channel x */ + +/* ADC_WDHT */ +#define ADC_WDHT_WDHT BITS(0,11) /*!< analog watchdog high threshold */ + +/* ADC_WDLT */ +#define ADC_WDLT_WDLT BITS(0,11) /*!< analog watchdog low threshold */ + +/* ADC_RSQx x=0..2 */ +#define ADC_RSQX_RSQN BITS(0,4) /*!< nth conversion in regular sequence */ +#define ADC_RSQ0_RL BITS(20,23) /*!< regular channel sequence length */ + +/* ADC_ISQ */ +#define ADC_ISQ_ISQN BITS(0,4) /*!< nth conversion in inserted sequence */ +#define ADC_ISQ_IL BITS(20,21) /*!< inserted sequence length */ + +/* ADC_IDATAx x=0..3*/ +#define ADC_IDATAX_IDATAN BITS(0,15) /*!< inserted data n */ + +/* ADC_RDATA */ +#define ADC_RDATA_RDATA BITS(0,15) /*!< regular data */ +#define ADC_RDATA_ADC1RDTR BITS(16,31) /*!< ADC1 regular channel data */ + +/* ADC_OVSCR */ +#define ADC_OVSCR_OVSEN BIT(0) /*!< oversampling enable */ +#define ADC_OVSCR_OVSR BITS(2,4) /*!< oversampling ratio */ +#define ADC_OVSCR_OVSS BITS(5,8) /*!< oversampling shift */ +#define ADC_OVSCR_TOVS BIT(9) /*!< triggered oversampling */ +#define ADC_OVSCR_DRES BITS(12,13) /*!< ADC data resolution */ + +/* constants definitions */ +/* adc_stat register value */ +#define ADC_FLAG_WDE ADC_STAT_WDE /*!< analog watchdog event flag */ +#define ADC_FLAG_EOC ADC_STAT_EOC /*!< end of conversion */ +#define ADC_FLAG_EOIC ADC_STAT_EOIC /*!< inserted channel end of conversion */ +#define ADC_FLAG_STIC ADC_STAT_STIC /*!< inserted channel start flag */ +#define ADC_FLAG_STRC ADC_STAT_STRC /*!< regular channel start flag */ + +/* adc_ctl0 register value */ +#define CTL0_DISNUM(regval) (BITS(13,15) & ((uint32_t)(regval) << 13)) /*!< write value to ADC_CTL0_DISNUM bit field */ + +/* scan mode */ +#define ADC_SCAN_MODE ADC_CTL0_SM /*!< scan mode */ + +/* inserted channel group convert automatically */ +#define ADC_INSERTED_CHANNEL_AUTO ADC_CTL0_ICA /*!< inserted channel group convert automatically */ + +/* ADC sync mode */ +#define CTL0_SYNCM(regval) (BITS(16,19) & ((uint32_t)(regval) << 16)) /*!< write value to ADC_CTL0_SYNCM bit field */ +#define ADC_MODE_FREE CTL0_SYNCM(0) /*!< all the ADCs work independently */ +#define ADC_DAUL_REGULAL_PARALLEL_INSERTED_PARALLEL CTL0_SYNCM(1) /*!< ADC0 and ADC1 work in combined regular parallel + inserted parallel mode */ +#define ADC_DAUL_REGULAL_PARALLEL_INSERTED_ROTATION CTL0_SYNCM(2) /*!< ADC0 and ADC1 work in combined regular parallel + trigger rotation mode */ +#define ADC_DAUL_INSERTED_PARALLEL_REGULAL_FOLLOWUP_FAST CTL0_SYNCM(3) /*!< ADC0 and ADC1 work in combined inserted parallel + follow-up fast mode */ +#define ADC_DAUL_INSERTED_PARALLEL_REGULAL_FOLLOWUP_SLOW CTL0_SYNCM(4) /*!< ADC0 and ADC1 work in combined inserted parallel + follow-up slow mode */ +#define ADC_DAUL_INSERTED_PARALLEL CTL0_SYNCM(5) /*!< ADC0 and ADC1 work in inserted parallel mode only */ +#define ADC_DAUL_REGULAL_PARALLEL CTL0_SYNCM(6) /*!< ADC0 and ADC1 work in regular parallel mode only */ +#define ADC_DAUL_REGULAL_FOLLOWUP_FAST CTL0_SYNCM(7) /*!< ADC0 and ADC1 work in follow-up fast mode only */ +#define ADC_DAUL_REGULAL_FOLLOWUP_SLOW CTL0_SYNCM(8) /*!< ADC0 and ADC1 work in follow-up slow mode only */ +#define ADC_DAUL_INSERTED_TRIGGER_ROTATION CTL0_SYNCM(9) /*!< ADC0 and ADC1 work in trigger rotation mode only */ + +/* adc_ctl1 register value */ +#define ADC_DATAALIGN_RIGHT ((uint32_t)0x00000000U) /*!< LSB alignment */ +#define ADC_DATAALIGN_LEFT ADC_CTL1_DAL /*!< MSB alignment */ + +/* continuous mode */ +#define ADC_CONTINUOUS_MODE ADC_CTL1_CTN /*!< continuous mode */ + +/* external trigger select for regular channel */ +#define CTL1_ETSRC(regval) (BITS(17,19) & ((uint32_t)(regval) << 17)) /*!< write value to ADC_CTL1_ETSRC bit field */ +/* for ADC0 and ADC1 regular channel */ +#define ADC0_1_EXTTRIG_REGULAR_T0_CH0 CTL1_ETSRC(0) /*!< TIMER0 CH0 event select */ +#define ADC0_1_EXTTRIG_REGULAR_T0_CH1 CTL1_ETSRC(1) /*!< TIMER0 CH1 event select */ +#define ADC0_1_EXTTRIG_REGULAR_T0_CH2 CTL1_ETSRC(2) /*!< TIMER0 CH2 event select */ +#define ADC0_1_EXTTRIG_REGULAR_T1_CH1 CTL1_ETSRC(3) /*!< TIMER1 CH1 event select */ +#define ADC0_1_EXTTRIG_REGULAR_T2_TRGO CTL1_ETSRC(4) /*!< TIMER2 TRGO event select */ +#define ADC0_1_EXTTRIG_REGULAR_T3_CH3 CTL1_ETSRC(5) /*!< TIMER3 CH3 event select */ +#define ADC0_1_EXTTRIG_REGULAR_EXTI_11 CTL1_ETSRC(6) /*!< external interrupt line 11 */ +#define ADC0_1_EXTTRIG_REGULAR_NONE CTL1_ETSRC(7) /*!< software trigger */ + +/* external trigger mode for inserted channel */ +#define CTL1_ETSIC(regval) (BITS(12,14) & ((uint32_t)(regval) << 12)) /*!< write value to ADC_CTL1_ETSIC bit field */ +/* for ADC0 and ADC1 inserted channel */ +#define ADC0_1_EXTTRIG_INSERTED_T0_TRGO CTL1_ETSIC(0) /*!< TIMER0 TRGO event select */ +#define ADC0_1_EXTTRIG_INSERTED_T0_CH3 CTL1_ETSIC(1) /*!< TIMER0 CH3 event select */ +#define ADC0_1_EXTTRIG_INSERTED_T1_TRGO CTL1_ETSIC(2) /*!< TIMER1 TRGO event select */ +#define ADC0_1_EXTTRIG_INSERTED_T1_CH0 CTL1_ETSIC(3) /*!< TIMER1 CH0 event select */ +#define ADC0_1_EXTTRIG_INSERTED_T2_CH3 CTL1_ETSIC(4) /*!< TIMER2 CH3 event select */ +#define ADC0_1_EXTTRIG_INSERTED_T3_TRGO CTL1_ETSIC(5) /*!< TIMER3 TRGO event select */ +#define ADC0_1_EXTTRIG_INSERTED_EXTI_15 CTL1_ETSIC(6) /*!< external interrupt line 15 */ +#define ADC0_1_EXTTRIG_INSERTED_NONE CTL1_ETSIC(7) /*!< software trigger */ + +/* adc_samptx register value */ +#define SAMPTX_SPT(regval) (BITS(0,2) & ((uint32_t)(regval) << 0)) /*!< write value to ADC_SAMPTX_SPT bit field */ +#define ADC_SAMPLETIME_1POINT5 SAMPTX_SPT(0) /*!< 1.5 sampling cycles */ +#define ADC_SAMPLETIME_7POINT5 SAMPTX_SPT(1) /*!< 7.5 sampling cycles */ +#define ADC_SAMPLETIME_13POINT5 SAMPTX_SPT(2) /*!< 13.5 sampling cycles */ +#define ADC_SAMPLETIME_28POINT5 SAMPTX_SPT(3) /*!< 28.5 sampling cycles */ +#define ADC_SAMPLETIME_41POINT5 SAMPTX_SPT(4) /*!< 41.5 sampling cycles */ +#define ADC_SAMPLETIME_55POINT5 SAMPTX_SPT(5) /*!< 55.5 sampling cycles */ +#define ADC_SAMPLETIME_71POINT5 SAMPTX_SPT(6) /*!< 71.5 sampling cycles */ +#define ADC_SAMPLETIME_239POINT5 SAMPTX_SPT(7) /*!< 239.5 sampling cycles */ + +/* adc_ioffx register value */ +#define IOFFX_IOFF(regval) (BITS(0,11) & ((uint32_t)(regval) << 0)) /*!< write value to ADC_IOFFX_IOFF bit field */ + +/* adc_wdht register value */ +#define WDHT_WDHT(regval) (BITS(0,11) & ((uint32_t)(regval) << 0)) /*!< write value to ADC_WDHT_WDHT bit field */ + +/* adc_wdlt register value */ +#define WDLT_WDLT(regval) (BITS(0,11) & ((uint32_t)(regval) << 0)) /*!< write value to ADC_WDLT_WDLT bit field */ + +/* adc_rsqx register value */ +#define RSQ0_RL(regval) (BITS(20,23) & ((uint32_t)(regval) << 20)) /*!< write value to ADC_RSQ0_RL bit field */ + +/* adc_isq register value */ +#define ISQ_IL(regval) (BITS(20,21) & ((uint32_t)(regval) << 20)) /*!< write value to ADC_ISQ_IL bit field */ + +/* ADC channel group definitions */ +#define ADC_REGULAR_CHANNEL ((uint8_t)0x01U) /*!< adc regular channel group */ +#define ADC_INSERTED_CHANNEL ((uint8_t)0x02U) /*!< adc inserted channel group */ +#define ADC_REGULAR_INSERTED_CHANNEL ((uint8_t)0x03U) /*!< both regular and inserted channel group */ + +#define ADC_CHANNEL_DISCON_DISABLE ((uint8_t)0x04U) /*!< disable discontinuous mode of regular & inserted channel */ + +/* ADC inserted channel definitions */ +#define ADC_INSERTED_CHANNEL_0 ((uint8_t)0x00U) /*!< adc inserted channel 0 */ +#define ADC_INSERTED_CHANNEL_1 ((uint8_t)0x01U) /*!< adc inserted channel 1 */ +#define ADC_INSERTED_CHANNEL_2 ((uint8_t)0x02U) /*!< adc inserted channel 2 */ +#define ADC_INSERTED_CHANNEL_3 ((uint8_t)0x03U) /*!< adc inserted channel 3 */ + +/* ADC channel definitions */ +#define ADC_CHANNEL_0 ((uint8_t)0x00U) /*!< ADC channel 0 */ +#define ADC_CHANNEL_1 ((uint8_t)0x01U) /*!< ADC channel 1 */ +#define ADC_CHANNEL_2 ((uint8_t)0x02U) /*!< ADC channel 2 */ +#define ADC_CHANNEL_3 ((uint8_t)0x03U) /*!< ADC channel 3 */ +#define ADC_CHANNEL_4 ((uint8_t)0x04U) /*!< ADC channel 4 */ +#define ADC_CHANNEL_5 ((uint8_t)0x05U) /*!< ADC channel 5 */ +#define ADC_CHANNEL_6 ((uint8_t)0x06U) /*!< ADC channel 6 */ +#define ADC_CHANNEL_7 ((uint8_t)0x07U) /*!< ADC channel 7 */ +#define ADC_CHANNEL_8 ((uint8_t)0x08U) /*!< ADC channel 8 */ +#define ADC_CHANNEL_9 ((uint8_t)0x09U) /*!< ADC channel 9 */ +#define ADC_CHANNEL_10 ((uint8_t)0x0AU) /*!< ADC channel 10 */ +#define ADC_CHANNEL_11 ((uint8_t)0x0BU) /*!< ADC channel 11 */ +#define ADC_CHANNEL_12 ((uint8_t)0x0CU) /*!< ADC channel 12 */ +#define ADC_CHANNEL_13 ((uint8_t)0x0DU) /*!< ADC channel 13 */ +#define ADC_CHANNEL_14 ((uint8_t)0x0EU) /*!< ADC channel 14 */ +#define ADC_CHANNEL_15 ((uint8_t)0x0FU) /*!< ADC channel 15 */ +#define ADC_CHANNEL_16 ((uint8_t)0x10U) /*!< ADC channel 16 */ +#define ADC_CHANNEL_17 ((uint8_t)0x11U) /*!< ADC channel 17 */ + +/* ADC interrupt */ +#define ADC_INT_WDE ADC_STAT_WDE /*!< analog watchdog event interrupt */ +#define ADC_INT_EOC ADC_STAT_EOC /*!< end of group conversion interrupt */ +#define ADC_INT_EOIC ADC_STAT_EOIC /*!< end of inserted group conversion interrupt */ + +/* ADC interrupt flag */ +#define ADC_INT_FLAG_WDE ADC_STAT_WDE /*!< analog watchdog event interrupt flag */ +#define ADC_INT_FLAG_EOC ADC_STAT_EOC /*!< end of group conversion interrupt flag */ +#define ADC_INT_FLAG_EOIC ADC_STAT_EOIC /*!< end of inserted group conversion interrupt flag */ + +/* ADC resolution definitions */ +#define OVSCR_DRES(regval) (BITS(12,13) & ((uint32_t)(regval) << 12)) +#define ADC_RESOLUTION_12B OVSCR_DRES(0) /*!< 12-bit ADC resolution */ +#define ADC_RESOLUTION_10B OVSCR_DRES(1) /*!< 10-bit ADC resolution */ +#define ADC_RESOLUTION_8B OVSCR_DRES(2) /*!< 8-bit ADC resolution */ +#define ADC_RESOLUTION_6B OVSCR_DRES(3) /*!< 6-bit ADC resolution */ + +/* ADC oversampling mode */ +#define ADC_OVERSAMPLING_ALL_CONVERT 0 /*!< all oversampled conversions for a channel are done consecutively after a trigger */ +#define ADC_OVERSAMPLING_ONE_CONVERT 1 /*!< each oversampled conversion for a channel needs a trigger */ + +/* ADC oversampling shift */ +#define OVSCR_OVSS(regval) (BITS(5,8) & ((uint32_t)(regval) << 5)) +#define ADC_OVERSAMPLING_SHIFT_NONE OVSCR_OVSS(0) /*!< no oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_1B OVSCR_OVSS(1) /*!< 1-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_2B OVSCR_OVSS(2) /*!< 2-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_3B OVSCR_OVSS(3) /*!< 3-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_4B OVSCR_OVSS(4) /*!< 4-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_5B OVSCR_OVSS(5) /*!< 5-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_6B OVSCR_OVSS(6) /*!< 6-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_7B OVSCR_OVSS(7) /*!< 7-bit oversampling shift */ +#define ADC_OVERSAMPLING_SHIFT_8B OVSCR_OVSS(8) /*!< 8-bit oversampling shift */ + +/* ADC oversampling ratio */ +#define OVSCR_OVSR(regval) (BITS(2,4) & ((uint32_t)(regval) << 2)) +#define ADC_OVERSAMPLING_RATIO_MUL2 OVSCR_OVSR(0) /*!< oversampling ratio X2 */ +#define ADC_OVERSAMPLING_RATIO_MUL4 OVSCR_OVSR(1) /*!< oversampling ratio X4 */ +#define ADC_OVERSAMPLING_RATIO_MUL8 OVSCR_OVSR(2) /*!< oversampling ratio X8 */ +#define ADC_OVERSAMPLING_RATIO_MUL16 OVSCR_OVSR(3) /*!< oversampling ratio X16 */ +#define ADC_OVERSAMPLING_RATIO_MUL32 OVSCR_OVSR(4) /*!< oversampling ratio X32 */ +#define ADC_OVERSAMPLING_RATIO_MUL64 OVSCR_OVSR(5) /*!< oversampling ratio X64 */ +#define ADC_OVERSAMPLING_RATIO_MUL128 OVSCR_OVSR(6) /*!< oversampling ratio X128 */ +#define ADC_OVERSAMPLING_RATIO_MUL256 OVSCR_OVSR(7) /*!< oversampling ratio X256 */ + +/* function declarations */ +/* initialization config */ +/* reset ADC */ +void adc_deinit(uint32_t adc_periph); +/* configure the ADC sync mode */ +void adc_mode_config(uint32_t adc_periph, uint32_t mode); +/* enable or disable ADC special function */ +void adc_special_function_config(uint32_t adc_periph, uint32_t function, ControlStatus newvalue); +/* configure ADC data alignment */ +void adc_data_alignment_config(uint32_t adc_periph, uint32_t data_alignment); +/* enable ADC interface */ +void adc_enable(uint32_t adc_periph); +/* disable ADC interface */ +void adc_disable(uint32_t adc_periph); +/* ADC calibration and reset calibration */ +void adc_calibration_enable(uint32_t adc_periph); +/* enable the temperature sensor and Vrefint channel */ +void adc_tempsensor_vrefint_enable(void); +/* disable the temperature sensor and Vrefint channel */ +void adc_tempsensor_vrefint_disable(void); + +/* DMA config */ +/* enable DMA request */ +void adc_dma_mode_enable(uint32_t adc_periph); +/* disable DMA request */ +void adc_dma_mode_disable(uint32_t adc_periph); + +/* regular group and inserted group config */ +/* configure ADC discontinuous mode */ +void adc_discontinuous_mode_config(uint32_t adc_periph, uint8_t adc_channel_group, uint8_t length); + +/* configure the length of regular channel group or inserted channel group */ +void adc_channel_length_config(uint32_t adc_periph, uint8_t adc_channel_group, uint32_t length); +/* configure ADC regular channel */ +void adc_regular_channel_config(uint32_t adc_periph, uint8_t rank, uint8_t adc_channel, uint32_t sample_time); +/* configure ADC inserted channel */ +void adc_inserted_channel_config(uint32_t adc_periph, uint8_t rank, uint8_t adc_channel, uint32_t sample_time); +/* configure ADC inserted channel offset */ +void adc_inserted_channel_offset_config(uint32_t adc_periph, uint8_t inserted_channel, uint16_t offset); + +/* configure ADC external trigger source */ +void adc_external_trigger_source_config(uint32_t adc_periph, uint8_t adc_channel_group, uint32_t external_trigger_source); +/* configure ADC external trigger */ +void adc_external_trigger_config(uint32_t adc_periph, uint8_t adc_channel_group, ControlStatus newvalue); +/* enable ADC software trigger */ +void adc_software_trigger_enable(uint32_t adc_periph, uint8_t adc_channel_group); + +/* get channel data */ +/* read ADC regular group data register */ +uint16_t adc_regular_data_read(uint32_t adc_periph); +/* read ADC inserted group data register */ +uint16_t adc_inserted_data_read(uint32_t adc_periph, uint8_t inserted_channel); +/* read the last ADC0 and ADC1 conversion result data in sync mode */ +uint32_t adc_sync_mode_convert_value_read(void); + +/* watchdog config */ +/* configure ADC analog watchdog single channel */ +void adc_watchdog_single_channel_enable(uint32_t adc_periph, uint8_t adc_channel); +/* configure ADC analog watchdog group channel */ +void adc_watchdog_group_channel_enable(uint32_t adc_periph, uint8_t adc_channel_group); +/* disable ADC analog watchdog */ +void adc_watchdog_disable(uint32_t adc_periph); +/* configure ADC analog watchdog threshold */ +void adc_watchdog_threshold_config(uint32_t adc_periph, uint16_t low_threshold, uint16_t high_threshold); + +/* interrupt & flag functions */ +/* get the ADC flag bits */ +FlagStatus adc_flag_get(uint32_t adc_periph, uint32_t adc_flag); +/* clear the ADC flag bits */ +void adc_flag_clear(uint32_t adc_periph, uint32_t adc_flag); +/* get the bit state of ADCx software start conversion */ +FlagStatus adc_regular_software_startconv_flag_get(uint32_t adc_periph); +/* get the bit state of ADCx software inserted channel start conversion */ +FlagStatus adc_inserted_software_startconv_flag_get(uint32_t adc_periph); +/* get the ADC interrupt bits */ +FlagStatus adc_interrupt_flag_get(uint32_t adc_periph, uint32_t adc_interrupt); +/* clear the ADC flag */ +void adc_interrupt_flag_clear(uint32_t adc_periph, uint32_t adc_interrupt); +/* enable ADC interrupt */ +void adc_interrupt_enable(uint32_t adc_periph, uint32_t adc_interrupt); +/* disable ADC interrupt */ +void adc_interrupt_disable(uint32_t adc_periph, uint32_t adc_interrupt); + +/* ADC resolution & oversample */ +/* ADC resolution config */ +void adc_resolution_config(uint32_t adc_periph, uint32_t resolution); +/* ADC oversample mode config */ +void adc_oversample_mode_config(uint32_t adc_periph, uint8_t mode, uint16_t shift, uint8_t ratio); +/* enable ADC oversample mode */ +void adc_oversample_mode_enable(uint32_t adc_periph); +/* disable ADC oversample mode */ +void adc_oversample_mode_disable(uint32_t adc_periph); + +#endif /* GD32VF103_ADC_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_bkp.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_bkp.h new file mode 100644 index 00000000..51384836 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_bkp.h @@ -0,0 +1,229 @@ +/*! + \file gd32vf103_bkp.h + \brief definitions for the BKP + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_BKP_H +#define GD32VF103_BKP_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* BKP definitions */ +#define BKP BKP_BASE /*!< BKP base address */ + +/* registers definitions */ +#define BKP_DATA0 REG16((BKP) + 0x04U) /*!< BKP data register 0 */ +#define BKP_DATA1 REG16((BKP) + 0x08U) /*!< BKP data register 1 */ +#define BKP_DATA2 REG16((BKP) + 0x0CU) /*!< BKP data register 2 */ +#define BKP_DATA3 REG16((BKP) + 0x10U) /*!< BKP data register 3 */ +#define BKP_DATA4 REG16((BKP) + 0x14U) /*!< BKP data register 4 */ +#define BKP_DATA5 REG16((BKP) + 0x18U) /*!< BKP data register 5 */ +#define BKP_DATA6 REG16((BKP) + 0x1CU) /*!< BKP data register 6 */ +#define BKP_DATA7 REG16((BKP) + 0x20U) /*!< BKP data register 7 */ +#define BKP_DATA8 REG16((BKP) + 0x24U) /*!< BKP data register 8 */ +#define BKP_DATA9 REG16((BKP) + 0x28U) /*!< BKP data register 9 */ +#define BKP_DATA10 REG16((BKP) + 0x40U) /*!< BKP data register 10 */ +#define BKP_DATA11 REG16((BKP) + 0x44U) /*!< BKP data register 11 */ +#define BKP_DATA12 REG16((BKP) + 0x48U) /*!< BKP data register 12 */ +#define BKP_DATA13 REG16((BKP) + 0x4CU) /*!< BKP data register 13 */ +#define BKP_DATA14 REG16((BKP) + 0x50U) /*!< BKP data register 14 */ +#define BKP_DATA15 REG16((BKP) + 0x54U) /*!< BKP data register 15 */ +#define BKP_DATA16 REG16((BKP) + 0x58U) /*!< BKP data register 16 */ +#define BKP_DATA17 REG16((BKP) + 0x5CU) /*!< BKP data register 17 */ +#define BKP_DATA18 REG16((BKP) + 0x60U) /*!< BKP data register 18 */ +#define BKP_DATA19 REG16((BKP) + 0x64U) /*!< BKP data register 19 */ +#define BKP_DATA20 REG16((BKP) + 0x68U) /*!< BKP data register 20 */ +#define BKP_DATA21 REG16((BKP) + 0x6CU) /*!< BKP data register 21 */ +#define BKP_DATA22 REG16((BKP) + 0x70U) /*!< BKP data register 22 */ +#define BKP_DATA23 REG16((BKP) + 0x74U) /*!< BKP data register 23 */ +#define BKP_DATA24 REG16((BKP) + 0x78U) /*!< BKP data register 24 */ +#define BKP_DATA25 REG16((BKP) + 0x7CU) /*!< BKP data register 25 */ +#define BKP_DATA26 REG16((BKP) + 0x80U) /*!< BKP data register 26 */ +#define BKP_DATA27 REG16((BKP) + 0x84U) /*!< BKP data register 27 */ +#define BKP_DATA28 REG16((BKP) + 0x88U) /*!< BKP data register 28 */ +#define BKP_DATA29 REG16((BKP) + 0x8CU) /*!< BKP data register 29 */ +#define BKP_DATA30 REG16((BKP) + 0x90U) /*!< BKP data register 30 */ +#define BKP_DATA31 REG16((BKP) + 0x94U) /*!< BKP data register 31 */ +#define BKP_DATA32 REG16((BKP) + 0x98U) /*!< BKP data register 32 */ +#define BKP_DATA33 REG16((BKP) + 0x9CU) /*!< BKP data register 33 */ +#define BKP_DATA34 REG16((BKP) + 0xA0U) /*!< BKP data register 34 */ +#define BKP_DATA35 REG16((BKP) + 0xA4U) /*!< BKP data register 35 */ +#define BKP_DATA36 REG16((BKP) + 0xA8U) /*!< BKP data register 36 */ +#define BKP_DATA37 REG16((BKP) + 0xACU) /*!< BKP data register 37 */ +#define BKP_DATA38 REG16((BKP) + 0xB0U) /*!< BKP data register 38 */ +#define BKP_DATA39 REG16((BKP) + 0xB4U) /*!< BKP data register 39 */ +#define BKP_DATA40 REG16((BKP) + 0xB8U) /*!< BKP data register 40 */ +#define BKP_DATA41 REG16((BKP) + 0xBCU) /*!< BKP data register 41 */ +#define BKP_OCTL REG16((BKP) + 0x2CU) /*!< RTC signal output control register */ +#define BKP_TPCTL REG16((BKP) + 0x30U) /*!< tamper pin control register */ +#define BKP_TPCS REG16((BKP) + 0x34U) /*!< tamper control and status register */ + +/* bits definitions */ +/* BKP_DATA */ +#define BKP_DATA BITS(0,15) /*!< backup data */ + +/* BKP_OCTL */ +#define BKP_OCTL_RCCV BITS(0,6) /*!< RTC clock calibration value */ +#define BKP_OCTL_COEN BIT(7) /*!< RTC clock calibration output enable */ +#define BKP_OCTL_ASOEN BIT(8) /*!< RTC alarm or second signal output enable */ +#define BKP_OCTL_ROSEL BIT(9) /*!< RTC output selection */ + +/* BKP_TPCTL */ +#define BKP_TPCTL_TPEN BIT(0) /*!< tamper detection enable */ +#define BKP_TPCTL_TPAL BIT(1) /*!< tamper pin active level */ + +/* BKP_TPCS */ +#define BKP_TPCS_TER BIT(0) /*!< tamper event reset */ +#define BKP_TPCS_TIR BIT(1) /*!< tamper interrupt reset */ +#define BKP_TPCS_TPIE BIT(2) /*!< tamper interrupt enable */ +#define BKP_TPCS_TEF BIT(8) /*!< tamper event flag */ +#define BKP_TPCS_TIF BIT(9) /*!< tamper interrupt flag */ + +/* constants definitions */ +/* BKP data register number */ +typedef enum +{ + BKP_DATA_0 = 1, /*!< BKP data register 0 */ + BKP_DATA_1, /*!< BKP data register 1 */ + BKP_DATA_2, /*!< BKP data register 2 */ + BKP_DATA_3, /*!< BKP data register 3 */ + BKP_DATA_4, /*!< BKP data register 4 */ + BKP_DATA_5, /*!< BKP data register 5 */ + BKP_DATA_6, /*!< BKP data register 6 */ + BKP_DATA_7, /*!< BKP data register 7 */ + BKP_DATA_8, /*!< BKP data register 8 */ + BKP_DATA_9, /*!< BKP data register 9 */ + BKP_DATA_10, /*!< BKP data register 10 */ + BKP_DATA_11, /*!< BKP data register 11 */ + BKP_DATA_12, /*!< BKP data register 12 */ + BKP_DATA_13, /*!< BKP data register 13 */ + BKP_DATA_14, /*!< BKP data register 14 */ + BKP_DATA_15, /*!< BKP data register 15 */ + BKP_DATA_16, /*!< BKP data register 16 */ + BKP_DATA_17, /*!< BKP data register 17 */ + BKP_DATA_18, /*!< BKP data register 18 */ + BKP_DATA_19, /*!< BKP data register 19 */ + BKP_DATA_20, /*!< BKP data register 20 */ + BKP_DATA_21, /*!< BKP data register 21 */ + BKP_DATA_22, /*!< BKP data register 22 */ + BKP_DATA_23, /*!< BKP data register 23 */ + BKP_DATA_24, /*!< BKP data register 24 */ + BKP_DATA_25, /*!< BKP data register 25 */ + BKP_DATA_26, /*!< BKP data register 26 */ + BKP_DATA_27, /*!< BKP data register 27 */ + BKP_DATA_28, /*!< BKP data register 28 */ + BKP_DATA_29, /*!< BKP data register 29 */ + BKP_DATA_30, /*!< BKP data register 30 */ + BKP_DATA_31, /*!< BKP data register 31 */ + BKP_DATA_32, /*!< BKP data register 32 */ + BKP_DATA_33, /*!< BKP data register 33 */ + BKP_DATA_34, /*!< BKP data register 34 */ + BKP_DATA_35, /*!< BKP data register 35 */ + BKP_DATA_36, /*!< BKP data register 36 */ + BKP_DATA_37, /*!< BKP data register 37 */ + BKP_DATA_38, /*!< BKP data register 38 */ + BKP_DATA_39, /*!< BKP data register 39 */ + BKP_DATA_40, /*!< BKP data register 40 */ + BKP_DATA_41, /*!< BKP data register 41 */ +}bkp_data_register_enum; + +/* BKP register */ +#define BKP_DATA0_9(number) REG16((BKP) + 0x04U + (number) * 0x04U) +#define BKP_DATA10_41(number) REG16((BKP) + 0x40U + ((number)-10U) * 0x04U) + +/* get data of BKP data register */ +#define BKP_DATA_GET(regval) GET_BITS((uint32_t)(regval), 0, 15) + +/* RTC clock calibration value */ +#define OCTL_RCCV(regval) (BITS(0,6) & ((uint32_t)(regval) << 0)) + +/* RTC output selection */ +#define RTC_OUTPUT_ALARM_PULSE ((uint16_t)0x0000U) /*!< RTC alarm pulse is selected as the RTC output */ +#define RTC_OUTPUT_SECOND_PULSE ((uint16_t)0x0200U) /*!< RTC second pulse is selected as the RTC output */ + +/* tamper pin active level */ +#define TAMPER_PIN_ACTIVE_HIGH ((uint16_t)0x0000U) /*!< the tamper pin is active high */ +#define TAMPER_PIN_ACTIVE_LOW ((uint16_t)0x0002U) /*!< the tamper pin is active low */ + +/* tamper flag */ +#define BKP_FLAG_TAMPER BKP_TPCS_TEF /*!< tamper event flag */ + +/* tamper interrupt flag */ +#define BKP_INT_FLAG_TAMPER BKP_TPCS_TIF /*!< tamper interrupt flag */ + +/* function declarations */ +/* reset BKP registers */ +void bkp_deinit(void); +/* write BKP data register */ +void bkp_data_write(bkp_data_register_enum register_number, uint16_t data); +/* read BKP data register */ +uint16_t bkp_data_read(bkp_data_register_enum register_number); + +/* RTC related functions */ +/* enable RTC clock calibration output */ +void bkp_rtc_calibration_output_enable(void); +/* disable RTC clock calibration output */ +void bkp_rtc_calibration_output_disable(void); +/* enable RTC alarm or second signal output */ +void bkp_rtc_signal_output_enable(void); +/* disable RTC alarm or second signal output */ +void bkp_rtc_signal_output_disable(void); +/* select RTC output */ +void bkp_rtc_output_select(uint16_t outputsel); +/* set RTC clock calibration value */ +void bkp_rtc_calibration_value_set(uint8_t value); + +/* tamper pin related functions */ +/* enable tamper pin detection */ +void bkp_tamper_detection_enable(void); +/* disable tamper pin detection */ +void bkp_tamper_detection_disable(void); +/* set tamper pin active level */ +void bkp_tamper_active_level_set(uint16_t level); + +/* interrupt & flag functions */ +/* enable tamper interrupt */ +void bkp_interrupt_enable(void); +/* disable tamper interrupt */ +void bkp_interrupt_disable(void); +/* get tamper flag state */ +FlagStatus bkp_flag_get(void); +/* clear tamper flag state */ +void bkp_flag_clear(void); +/* get tamper interrupt flag state */ +FlagStatus bkp_interrupt_flag_get(void); +/* clear tamper interrupt flag state */ +void bkp_interrupt_flag_clear(void); + +#endif /* GD32VF103_BKP_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_can.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_can.h new file mode 100644 index 00000000..04ae0508 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_can.h @@ -0,0 +1,720 @@ +/*! + \file gd32vf103_can.h + \brief definitions for the CAN + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_CAN_H +#define GD32VF103_CAN_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* CAN definitions */ +#define CAN0 CAN_BASE /*!< CAN0 base address */ +#define CAN1 (CAN0 + 0x00000400U) /*!< CAN1 base address */ + + +/* registers definitions */ +#define CAN_CTL(canx) REG32((canx) + 0x00U) /*!< CAN control register */ +#define CAN_STAT(canx) REG32((canx) + 0x04U) /*!< CAN status register */ +#define CAN_TSTAT(canx) REG32((canx) + 0x08U) /*!< CAN transmit status register*/ +#define CAN_RFIFO0(canx) REG32((canx) + 0x0CU) /*!< CAN receive FIFO0 register */ +#define CAN_RFIFO1(canx) REG32((canx) + 0x10U) /*!< CAN receive FIFO1 register */ +#define CAN_INTEN(canx) REG32((canx) + 0x14U) /*!< CAN interrupt enable register */ +#define CAN_ERR(canx) REG32((canx) + 0x18U) /*!< CAN error register */ +#define CAN_BT(canx) REG32((canx) + 0x1CU) /*!< CAN bit timing register */ +#define CAN_TMI0(canx) REG32((canx) + 0x180U) /*!< CAN transmit mailbox0 identifier register */ +#define CAN_TMP0(canx) REG32((canx) + 0x184U) /*!< CAN transmit mailbox0 property register */ +#define CAN_TMDATA00(canx) REG32((canx) + 0x188U) /*!< CAN transmit mailbox0 data0 register */ +#define CAN_TMDATA10(canx) REG32((canx) + 0x18CU) /*!< CAN transmit mailbox0 data1 register */ +#define CAN_TMI1(canx) REG32((canx) + 0x190U) /*!< CAN transmit mailbox1 identifier register */ +#define CAN_TMP1(canx) REG32((canx) + 0x194U) /*!< CAN transmit mailbox1 property register */ +#define CAN_TMDATA01(canx) REG32((canx) + 0x198U) /*!< CAN transmit mailbox1 data0 register */ +#define CAN_TMDATA11(canx) REG32((canx) + 0x19CU) /*!< CAN transmit mailbox1 data1 register */ +#define CAN_TMI2(canx) REG32((canx) + 0x1A0U) /*!< CAN transmit mailbox2 identifier register */ +#define CAN_TMP2(canx) REG32((canx) + 0x1A4U) /*!< CAN transmit mailbox2 property register */ +#define CAN_TMDATA02(canx) REG32((canx) + 0x1A8U) /*!< CAN transmit mailbox2 data0 register */ +#define CAN_TMDATA12(canx) REG32((canx) + 0x1ACU) /*!< CAN transmit mailbox2 data1 register */ +#define CAN_RFIFOMI0(canx) REG32((canx) + 0x1B0U) /*!< CAN receive FIFO0 mailbox identifier register */ +#define CAN_RFIFOMP0(canx) REG32((canx) + 0x1B4U) /*!< CAN receive FIFO0 mailbox property register */ +#define CAN_RFIFOMDATA00(canx) REG32((canx) + 0x1B8U) /*!< CAN receive FIFO0 mailbox data0 register */ +#define CAN_RFIFOMDATA10(canx) REG32((canx) + 0x1BCU) /*!< CAN receive FIFO0 mailbox data1 register */ +#define CAN_RFIFOMI1(canx) REG32((canx) + 0x1C0U) /*!< CAN receive FIFO1 mailbox identifier register */ +#define CAN_RFIFOMP1(canx) REG32((canx) + 0x1C4U) /*!< CAN receive FIFO1 mailbox property register */ +#define CAN_RFIFOMDATA01(canx) REG32((canx) + 0x1C8U) /*!< CAN receive FIFO1 mailbox data0 register */ +#define CAN_RFIFOMDATA11(canx) REG32((canx) + 0x1CCU) /*!< CAN receive FIFO1 mailbox data1 register */ +#define CAN_FCTL(canx) REG32((canx) + 0x200U) /*!< CAN filter control register */ +#define CAN_FMCFG(canx) REG32((canx) + 0x204U) /*!< CAN filter mode register */ +#define CAN_FSCFG(canx) REG32((canx) + 0x20CU) /*!< CAN filter scale register */ +#define CAN_FAFIFO(canx) REG32((canx) + 0x214U) /*!< CAN filter associated FIFO register */ +#define CAN_FW(canx) REG32((canx) + 0x21CU) /*!< CAN filter working register */ +#define CAN_F0DATA0(canx) REG32((canx) + 0x240U) /*!< CAN filter 0 data 0 register */ +#define CAN_F1DATA0(canx) REG32((canx) + 0x248U) /*!< CAN filter 1 data 0 register */ +#define CAN_F2DATA0(canx) REG32((canx) + 0x250U) /*!< CAN filter 2 data 0 register */ +#define CAN_F3DATA0(canx) REG32((canx) + 0x258U) /*!< CAN filter 3 data 0 register */ +#define CAN_F4DATA0(canx) REG32((canx) + 0x260U) /*!< CAN filter 4 data 0 register */ +#define CAN_F5DATA0(canx) REG32((canx) + 0x268U) /*!< CAN filter 5 data 0 register */ +#define CAN_F6DATA0(canx) REG32((canx) + 0x270U) /*!< CAN filter 6 data 0 register */ +#define CAN_F7DATA0(canx) REG32((canx) + 0x278U) /*!< CAN filter 7 data 0 register */ +#define CAN_F8DATA0(canx) REG32((canx) + 0x280U) /*!< CAN filter 8 data 0 register */ +#define CAN_F9DATA0(canx) REG32((canx) + 0x288U) /*!< CAN filter 9 data 0 register */ +#define CAN_F10DATA0(canx) REG32((canx) + 0x290U) /*!< CAN filter 10 data 0 register */ +#define CAN_F11DATA0(canx) REG32((canx) + 0x298U) /*!< CAN filter 11 data 0 register */ +#define CAN_F12DATA0(canx) REG32((canx) + 0x2A0U) /*!< CAN filter 12 data 0 register */ +#define CAN_F13DATA0(canx) REG32((canx) + 0x2A8U) /*!< CAN filter 13 data 0 register */ +#define CAN_F14DATA0(canx) REG32((canx) + 0x2B0U) /*!< CAN filter 14 data 0 register */ +#define CAN_F15DATA0(canx) REG32((canx) + 0x2B8U) /*!< CAN filter 15 data 0 register */ +#define CAN_F16DATA0(canx) REG32((canx) + 0x2C0U) /*!< CAN filter 16 data 0 register */ +#define CAN_F17DATA0(canx) REG32((canx) + 0x2C8U) /*!< CAN filter 17 data 0 register */ +#define CAN_F18DATA0(canx) REG32((canx) + 0x2D0U) /*!< CAN filter 18 data 0 register */ +#define CAN_F19DATA0(canx) REG32((canx) + 0x2D8U) /*!< CAN filter 19 data 0 register */ +#define CAN_F20DATA0(canx) REG32((canx) + 0x2E0U) /*!< CAN filter 20 data 0 register */ +#define CAN_F21DATA0(canx) REG32((canx) + 0x2E8U) /*!< CAN filter 21 data 0 register */ +#define CAN_F22DATA0(canx) REG32((canx) + 0x2F0U) /*!< CAN filter 22 data 0 register */ +#define CAN_F23DATA0(canx) REG32((canx) + 0x3F8U) /*!< CAN filter 23 data 0 register */ +#define CAN_F24DATA0(canx) REG32((canx) + 0x300U) /*!< CAN filter 24 data 0 register */ +#define CAN_F25DATA0(canx) REG32((canx) + 0x308U) /*!< CAN filter 25 data 0 register */ +#define CAN_F26DATA0(canx) REG32((canx) + 0x310U) /*!< CAN filter 26 data 0 register */ +#define CAN_F27DATA0(canx) REG32((canx) + 0x318U) /*!< CAN filter 27 data 0 register */ +#define CAN_F0DATA1(canx) REG32((canx) + 0x244U) /*!< CAN filter 0 data 1 register */ +#define CAN_F1DATA1(canx) REG32((canx) + 0x24CU) /*!< CAN filter 1 data 1 register */ +#define CAN_F2DATA1(canx) REG32((canx) + 0x254U) /*!< CAN filter 2 data 1 register */ +#define CAN_F3DATA1(canx) REG32((canx) + 0x25CU) /*!< CAN filter 3 data 1 register */ +#define CAN_F4DATA1(canx) REG32((canx) + 0x264U) /*!< CAN filter 4 data 1 register */ +#define CAN_F5DATA1(canx) REG32((canx) + 0x26CU) /*!< CAN filter 5 data 1 register */ +#define CAN_F6DATA1(canx) REG32((canx) + 0x274U) /*!< CAN filter 6 data 1 register */ +#define CAN_F7DATA1(canx) REG32((canx) + 0x27CU) /*!< CAN filter 7 data 1 register */ +#define CAN_F8DATA1(canx) REG32((canx) + 0x284U) /*!< CAN filter 8 data 1 register */ +#define CAN_F9DATA1(canx) REG32((canx) + 0x28CU) /*!< CAN filter 9 data 1 register */ +#define CAN_F10DATA1(canx) REG32((canx) + 0x294U) /*!< CAN filter 10 data 1 register */ +#define CAN_F11DATA1(canx) REG32((canx) + 0x29CU) /*!< CAN filter 11 data 1 register */ +#define CAN_F12DATA1(canx) REG32((canx) + 0x2A4U) /*!< CAN filter 12 data 1 register */ +#define CAN_F13DATA1(canx) REG32((canx) + 0x2ACU) /*!< CAN filter 13 data 1 register */ +#define CAN_F14DATA1(canx) REG32((canx) + 0x2B4U) /*!< CAN filter 14 data 1 register */ +#define CAN_F15DATA1(canx) REG32((canx) + 0x2BCU) /*!< CAN filter 15 data 1 register */ +#define CAN_F16DATA1(canx) REG32((canx) + 0x2C4U) /*!< CAN filter 16 data 1 register */ +#define CAN_F17DATA1(canx) REG32((canx) + 0x24CU) /*!< CAN filter 17 data 1 register */ +#define CAN_F18DATA1(canx) REG32((canx) + 0x2D4U) /*!< CAN filter 18 data 1 register */ +#define CAN_F19DATA1(canx) REG32((canx) + 0x2DCU) /*!< CAN filter 19 data 1 register */ +#define CAN_F20DATA1(canx) REG32((canx) + 0x2E4U) /*!< CAN filter 20 data 1 register */ +#define CAN_F21DATA1(canx) REG32((canx) + 0x2ECU) /*!< CAN filter 21 data 1 register */ +#define CAN_F22DATA1(canx) REG32((canx) + 0x2F4U) /*!< CAN filter 22 data 1 register */ +#define CAN_F23DATA1(canx) REG32((canx) + 0x2FCU) /*!< CAN filter 23 data 1 register */ +#define CAN_F24DATA1(canx) REG32((canx) + 0x304U) /*!< CAN filter 24 data 1 register */ +#define CAN_F25DATA1(canx) REG32((canx) + 0x30CU) /*!< CAN filter 25 data 1 register */ +#define CAN_F26DATA1(canx) REG32((canx) + 0x314U) /*!< CAN filter 26 data 1 register */ +#define CAN_F27DATA1(canx) REG32((canx) + 0x31CU) /*!< CAN filter 27 data 1 register */ + +/* CAN transmit mailbox bank */ +#define CAN_TMI(canx, bank) REG32((canx) + 0x180U + ((bank) * 0x10U)) /*!< CAN transmit mailbox identifier register */ +#define CAN_TMP(canx, bank) REG32((canx) + 0x184U + ((bank) * 0x10U)) /*!< CAN transmit mailbox property register */ +#define CAN_TMDATA0(canx, bank) REG32((canx) + 0x188U + ((bank) * 0x10U)) /*!< CAN transmit mailbox data0 register */ +#define CAN_TMDATA1(canx, bank) REG32((canx) + 0x18CU + ((bank) * 0x10U)) /*!< CAN transmit mailbox data1 register */ + +/* CAN filter bank */ +#define CAN_FDATA0(canx, bank) REG32((canx) + 0x240U + ((bank) * 0x8U) + 0x0U) /*!< CAN filter data 0 register */ +#define CAN_FDATA1(canx, bank) REG32((canx) + 0x240U + ((bank) * 0x8U) + 0x4U) /*!< CAN filter data 1 register */ + +/* CAN receive fifo mailbox bank */ +#define CAN_RFIFOMI(canx, bank) REG32((canx) + 0x1B0U + ((bank) * 0x10U)) /*!< CAN receive FIFO mailbox identifier register */ +#define CAN_RFIFOMP(canx, bank) REG32((canx) + 0x1B4U + ((bank) * 0x10U)) /*!< CAN receive FIFO mailbox property register */ +#define CAN_RFIFOMDATA0(canx, bank) REG32((canx) + 0x1B8U + ((bank) * 0x10U)) /*!< CAN receive FIFO mailbox data0 register */ +#define CAN_RFIFOMDATA1(canx, bank) REG32((canx) + 0x1BCU + ((bank) * 0x10U)) /*!< CAN receive FIFO mailbox data1 register */ + +/* bits definitions */ +/* CAN_CTL */ +#define CAN_CTL_IWMOD BIT(0) /*!< initial working mode */ +#define CAN_CTL_SLPWMOD BIT(1) /*!< sleep working mode */ +#define CAN_CTL_TFO BIT(2) /*!< transmit FIFO order */ +#define CAN_CTL_RFOD BIT(3) /*!< receive FIFO overwrite disable */ +#define CAN_CTL_ARD BIT(4) /*!< automatic retransmission disable */ +#define CAN_CTL_AWU BIT(5) /*!< automatic wakeup */ +#define CAN_CTL_ABOR BIT(6) /*!< automatic bus-off recovery */ +#define CAN_CTL_TTC BIT(7) /*!< time triggered communication */ +#define CAN_CTL_SWRST BIT(15) /*!< CAN software reset */ +#define CAN_CTL_DFZ BIT(16) /*!< CAN debug freeze */ + +/* CAN_STAT */ +#define CAN_STAT_IWS BIT(0) /*!< initial working state */ +#define CAN_STAT_SLPWS BIT(1) /*!< sleep working state */ +#define CAN_STAT_ERRIF BIT(2) /*!< error interrupt flag*/ +#define CAN_STAT_WUIF BIT(3) /*!< status change interrupt flag of wakeup from sleep working mode */ +#define CAN_STAT_SLPIF BIT(4) /*!< status change interrupt flag of sleep working mode entering */ +#define CAN_STAT_TS BIT(8) /*!< transmitting state */ +#define CAN_STAT_RS BIT(9) /*!< receiving state */ +#define CAN_STAT_LASTRX BIT(10) /*!< last sample value of rx pin */ +#define CAN_STAT_RXL BIT(11) /*!< CAN rx signal */ + +/* CAN_TSTAT */ +#define CAN_TSTAT_MTF0 BIT(0) /*!< mailbox0 transmit finished */ +#define CAN_TSTAT_MTFNERR0 BIT(1) /*!< mailbox0 transmit finished and no error */ +#define CAN_TSTAT_MAL0 BIT(2) /*!< mailbox0 arbitration lost */ +#define CAN_TSTAT_MTE0 BIT(3) /*!< mailbox0 transmit error */ +#define CAN_TSTAT_MST0 BIT(7) /*!< mailbox0 stop transmitting */ +#define CAN_TSTAT_MTF1 BIT(8) /*!< mailbox1 transmit finished */ +#define CAN_TSTAT_MTFNERR1 BIT(9) /*!< mailbox1 transmit finished and no error */ +#define CAN_TSTAT_MAL1 BIT(10) /*!< mailbox1 arbitration lost */ +#define CAN_TSTAT_MTE1 BIT(11) /*!< mailbox1 transmit error */ +#define CAN_TSTAT_MST1 BIT(15) /*!< mailbox1 stop transmitting */ +#define CAN_TSTAT_MTF2 BIT(16) /*!< mailbox2 transmit finished */ +#define CAN_TSTAT_MTFNERR2 BIT(17) /*!< mailbox2 transmit finished and no error */ +#define CAN_TSTAT_MAL2 BIT(18) /*!< mailbox2 arbitration lost */ +#define CAN_TSTAT_MTE2 BIT(19) /*!< mailbox2 transmit error */ +#define CAN_TSTAT_MST2 BIT(23) /*!< mailbox2 stop transmitting */ +#define CAN_TSTAT_NUM BITS(24,25) /*!< mailbox number */ +#define CAN_TSTAT_TME0 BIT(26) /*!< transmit mailbox0 empty */ +#define CAN_TSTAT_TME1 BIT(27) /*!< transmit mailbox1 empty */ +#define CAN_TSTAT_TME2 BIT(28) /*!< transmit mailbox2 empty */ +#define CAN_TSTAT_TMLS0 BIT(29) /*!< last sending priority flag for mailbox0 */ +#define CAN_TSTAT_TMLS1 BIT(30) /*!< last sending priority flag for mailbox1 */ +#define CAN_TSTAT_TMLS2 BIT(31) /*!< last sending priority flag for mailbox2 */ + +/* CAN_RFIFO0 */ +#define CAN_RFIFO0_RFL0 BITS(0,1) /*!< receive FIFO0 length */ +#define CAN_RFIFO0_RFF0 BIT(3) /*!< receive FIFO0 full */ +#define CAN_RFIFO0_RFO0 BIT(4) /*!< receive FIFO0 overfull */ +#define CAN_RFIFO0_RFD0 BIT(5) /*!< receive FIFO0 dequeue */ + +/* CAN_RFIFO1 */ +#define CAN_RFIFO1_RFL1 BITS(0,1) /*!< receive FIFO1 length */ +#define CAN_RFIFO1_RFF1 BIT(3) /*!< receive FIFO1 full */ +#define CAN_RFIFO1_RFO1 BIT(4) /*!< receive FIFO1 overfull */ +#define CAN_RFIFO1_RFD1 BIT(5) /*!< receive FIFO1 dequeue */ + +/* CAN_INTEN */ +#define CAN_INTEN_TMEIE BIT(0) /*!< transmit mailbox empty interrupt enable */ +#define CAN_INTEN_RFNEIE0 BIT(1) /*!< receive FIFO0 not empty interrupt enable */ +#define CAN_INTEN_RFFIE0 BIT(2) /*!< receive FIFO0 full interrupt enable */ +#define CAN_INTEN_RFOIE0 BIT(3) /*!< receive FIFO0 overfull interrupt enable */ +#define CAN_INTEN_RFNEIE1 BIT(4) /*!< receive FIFO1 not empty interrupt enable */ +#define CAN_INTEN_RFFIE1 BIT(5) /*!< receive FIFO1 full interrupt enable */ +#define CAN_INTEN_RFOIE1 BIT(6) /*!< receive FIFO1 overfull interrupt enable */ +#define CAN_INTEN_WERRIE BIT(8) /*!< warning error interrupt enable */ +#define CAN_INTEN_PERRIE BIT(9) /*!< passive error interrupt enable */ +#define CAN_INTEN_BOIE BIT(10) /*!< bus-off interrupt enable */ +#define CAN_INTEN_ERRNIE BIT(11) /*!< error number interrupt enable */ +#define CAN_INTEN_ERRIE BIT(15) /*!< error interrupt enable */ +#define CAN_INTEN_WIE BIT(16) /*!< wakeup interrupt enable */ +#define CAN_INTEN_SLPWIE BIT(17) /*!< sleep working interrupt enable */ + +/* CAN_ERR */ +#define CAN_ERR_WERR BIT(0) /*!< warning error */ +#define CAN_ERR_PERR BIT(1) /*!< passive error */ +#define CAN_ERR_BOERR BIT(2) /*!< bus-off error */ +#define CAN_ERR_ERRN BITS(4,6) /*!< error number */ +#define CAN_ERR_TECNT BITS(16,23) /*!< transmit error count */ +#define CAN_ERR_RECNT BITS(24,31) /*!< receive error count */ + +/* CAN_BT */ +#define CAN_BT_BAUDPSC BITS(0,9) /*!< baudrate prescaler */ +#define CAN_BT_BS1 BITS(16,19) /*!< bit segment 1 */ +#define CAN_BT_BS2 BITS(20,22) /*!< bit segment 2 */ +#define CAN_BT_SJW BITS(24,25) /*!< resynchronization jump width */ +#define CAN_BT_LCMOD BIT(30) /*!< loopback communication mode */ +#define CAN_BT_SCMOD BIT(31) /*!< silent communication mode */ + +/* CAN_TMIx */ +#define CAN_TMI_TEN BIT(0) /*!< transmit enable */ +#define CAN_TMI_FT BIT(1) /*!< frame type */ +#define CAN_TMI_FF BIT(2) /*!< frame format */ +#define CAN_TMI_EFID BITS(3,31) /*!< the frame identifier */ +#define CAN_TMI_SFID BITS(21,31) /*!< the frame identifier */ + +/* CAN_TMPx */ +#define CAN_TMP_DLENC BITS(0,3) /*!< data length code */ +#define CAN_TMP_TSEN BIT(8) /*!< time stamp enable */ +#define CAN_TMP_TS BITS(16,31) /*!< time stamp */ + +/* CAN_TMDATA0x */ +#define CAN_TMDATA0_DB0 BITS(0,7) /*!< transmit data byte 0 */ +#define CAN_TMDATA0_DB1 BITS(8,15) /*!< transmit data byte 1 */ +#define CAN_TMDATA0_DB2 BITS(16,23) /*!< transmit data byte 2 */ +#define CAN_TMDATA0_DB3 BITS(24,31) /*!< transmit data byte 3 */ + +/* CAN_TMDATA1x */ +#define CAN_TMDATA1_DB4 BITS(0,7) /*!< transmit data byte 4 */ +#define CAN_TMDATA1_DB5 BITS(8,15) /*!< transmit data byte 5 */ +#define CAN_TMDATA1_DB6 BITS(16,23) /*!< transmit data byte 6 */ +#define CAN_TMDATA1_DB7 BITS(24,31) /*!< transmit data byte 7 */ + +/* CAN_RFIFOMIx */ +#define CAN_RFIFOMI_FT BIT(1) /*!< frame type */ +#define CAN_RFIFOMI_FF BIT(2) /*!< frame format */ +#define CAN_RFIFOMI_EFID BITS(3,31) /*!< the frame identifier */ +#define CAN_RFIFOMI_SFID BITS(21,31) /*!< the frame identifier */ + +/* CAN_RFIFOMPx */ +#define CAN_RFIFOMP_DLENC BITS(0,3) /*!< receive data length code */ +#define CAN_RFIFOMP_FI BITS(8,15) /*!< filter index */ +#define CAN_RFIFOMP_TS BITS(16,31) /*!< time stamp */ + +/* CAN_RFIFOMDATA0x */ +#define CAN_RFIFOMDATA0_DB0 BITS(0,7) /*!< receive data byte 0 */ +#define CAN_RFIFOMDATA0_DB1 BITS(8,15) /*!< receive data byte 1 */ +#define CAN_RFIFOMDATA0_DB2 BITS(16,23) /*!< receive data byte 2 */ +#define CAN_RFIFOMDATA0_DB3 BITS(24,31) /*!< receive data byte 3 */ + +/* CAN_RFIFOMDATA1x */ +#define CAN_RFIFOMDATA1_DB4 BITS(0,7) /*!< receive data byte 4 */ +#define CAN_RFIFOMDATA1_DB5 BITS(8,15) /*!< receive data byte 5 */ +#define CAN_RFIFOMDATA1_DB6 BITS(16,23) /*!< receive data byte 6 */ +#define CAN_RFIFOMDATA1_DB7 BITS(24,31) /*!< receive data byte 7 */ + +/* CAN_FCTL */ +#define CAN_FCTL_FLD BIT(0) /*!< filter lock disable */ +#define CAN_FCTL_HBC1F BITS(8,13) /*!< header bank of CAN1 filter */ + +/* CAN_FMCFG */ +#define CAN_FMCFG_FMOD(regval) BIT(regval) /*!< filter mode, list or mask*/ + +/* CAN_FSCFG */ +#define CAN_FSCFG_FS(regval) BIT(regval) /*!< filter scale, 32 bits or 16 bits*/ + +/* CAN_FAFIFO */ +#define CAN_FAFIFOR_FAF(regval) BIT(regval) /*!< filter associated with FIFO */ + +/* CAN_FW */ +#define CAN_FW_FW(regval) BIT(regval) /*!< filter working */ + +/* CAN_FxDATAy */ +#define CAN_FDATA_FD(regval) BIT(regval) /*!< filter data */ + +/* consts definitions */ +/* define the CAN bit position and its register index offset */ +#define CAN_REGIDX_BIT(regidx, bitpos) (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos)) +#define CAN_REG_VAL(canx, offset) (REG32((canx) + ((uint32_t)(offset) >> 6))) +#define CAN_BIT_POS(val) ((uint32_t)(val) & 0x1FU) + +#define CAN_REGIDX_BITS(regidx, bitpos0, bitpos1) (((uint32_t)(regidx) << 12) | ((uint32_t)(bitpos0) << 6) | (uint32_t)(bitpos1)) +#define CAN_REG_VALS(canx, offset) (REG32((canx) + ((uint32_t)(offset) >> 12))) +#define CAN_BIT_POS0(val) (((uint32_t)(val) >> 6) & 0x1FU) +#define CAN_BIT_POS1(val) ((uint32_t)(val) & 0x1FU) + +/* register offset */ +#define STAT_REG_OFFSET ((uint8_t)0x04U) /*!< STAT register offset */ +#define TSTAT_REG_OFFSET ((uint8_t)0x08U) /*!< TSTAT register offset */ +#define RFIFO0_REG_OFFSET ((uint8_t)0x0CU) /*!< RFIFO0 register offset */ +#define RFIFO1_REG_OFFSET ((uint8_t)0x10U) /*!< RFIFO1 register offset */ +#define ERR_REG_OFFSET ((uint8_t)0x18U) /*!< ERR register offset */ + +/* CAN flags */ +typedef enum { + /* flags in TSTAT register */ + CAN_FLAG_MTE2 = CAN_REGIDX_BIT(TSTAT_REG_OFFSET, 19U), /*!< mailbox 2 transmit error */ + CAN_FLAG_MTE1 = CAN_REGIDX_BIT(TSTAT_REG_OFFSET, 11U), /*!< mailbox 1 transmit error */ + CAN_FLAG_MTE0 = CAN_REGIDX_BIT(TSTAT_REG_OFFSET, 3U), /*!< mailbox 0 transmit error */ + CAN_FLAG_MTF2 = CAN_REGIDX_BIT(TSTAT_REG_OFFSET, 16U), /*!< mailbox 2 transmit finished */ + CAN_FLAG_MTF1 = CAN_REGIDX_BIT(TSTAT_REG_OFFSET, 8U), /*!< mailbox 1 transmit finished */ + CAN_FLAG_MTF0 = CAN_REGIDX_BIT(TSTAT_REG_OFFSET, 0U), /*!< mailbox 0 transmit finished */ + /* flags in RFIFO0 register */ + CAN_FLAG_RFO0 = CAN_REGIDX_BIT(RFIFO0_REG_OFFSET, 4U), /*!< receive FIFO0 overfull */ + CAN_FLAG_RFF0 = CAN_REGIDX_BIT(RFIFO0_REG_OFFSET, 3U), /*!< receive FIFO0 full */ + /* flags in RFIFO1 register */ + CAN_FLAG_RFO1 = CAN_REGIDX_BIT(RFIFO1_REG_OFFSET, 4U), /*!< receive FIFO1 overfull */ + CAN_FLAG_RFF1 = CAN_REGIDX_BIT(RFIFO1_REG_OFFSET, 3U), /*!< receive FIFO1 full */ + /* flags in ERR register */ + CAN_FLAG_BOERR = CAN_REGIDX_BIT(ERR_REG_OFFSET, 2U), /*!< bus-off error */ + CAN_FLAG_PERR = CAN_REGIDX_BIT(ERR_REG_OFFSET, 1U), /*!< passive error */ + CAN_FLAG_WERR = CAN_REGIDX_BIT(ERR_REG_OFFSET, 0U), /*!< warning error */ +} can_flag_enum; + +/* CAN interrupt flags */ +typedef enum { + /* interrupt flags in STAT register */ + CAN_INT_FLAG_SLPIF = CAN_REGIDX_BITS(STAT_REG_OFFSET, 4U, 17U), /*!< status change interrupt flag of sleep working mode entering */ + CAN_INT_FLAG_WUIF = CAN_REGIDX_BITS(STAT_REG_OFFSET, 3U, 16), /*!< status change interrupt flag of wakeup from sleep working mode */ + CAN_INT_FLAG_ERRIF = CAN_REGIDX_BITS(STAT_REG_OFFSET, 2U, 15), /*!< error interrupt flag */ + /* interrupt flags in TSTAT register */ + CAN_INT_FLAG_MTF2 = CAN_REGIDX_BITS(TSTAT_REG_OFFSET, 16U, 0U), /*!< mailbox 2 transmit finished interrupt flag */ + CAN_INT_FLAG_MTF1 = CAN_REGIDX_BITS(TSTAT_REG_OFFSET, 8U, 0U), /*!< mailbox 1 transmit finished interrupt flag */ + CAN_INT_FLAG_MTF0 = CAN_REGIDX_BITS(TSTAT_REG_OFFSET, 0U, 0U), /*!< mailbox 0 transmit finished interrupt flag */ + /* interrupt flags in RFIFO0 register */ + CAN_INT_FLAG_RFO0 = CAN_REGIDX_BITS(RFIFO0_REG_OFFSET, 4U, 3U), /*!< receive FIFO0 overfull interrupt flag */ + CAN_INT_FLAG_RFF0 = CAN_REGIDX_BITS(RFIFO0_REG_OFFSET, 3U, 2U), /*!< receive FIFO0 full interrupt flag */ + /* interrupt flags in RFIFO0 register */ + CAN_INT_FLAG_RFO1 = CAN_REGIDX_BITS(RFIFO1_REG_OFFSET, 4U, 6U), /*!< receive FIFO1 overfull interrupt flag */ + CAN_INT_FLAG_RFF1 = CAN_REGIDX_BITS(RFIFO1_REG_OFFSET, 3U, 5U), /*!< receive FIFO1 full interrupt flag */ +} can_interrupt_flag_enum; + +/* CAN initiliaze parameters struct */ +typedef struct { + uint8_t working_mode; /*!< CAN working mode */ + uint8_t resync_jump_width; /*!< CAN resynchronization jump width */ + uint8_t time_segment_1; /*!< time segment 1 */ + uint8_t time_segment_2; /*!< time segment 2 */ + ControlStatus time_triggered; /*!< time triggered communication mode */ + ControlStatus auto_bus_off_recovery; /*!< automatic bus-off recovery */ + ControlStatus auto_wake_up; /*!< automatic wake-up mode */ + ControlStatus no_auto_retrans; /*!< automatic retransmission mode disable */ + ControlStatus rec_fifo_overwrite; /*!< receive FIFO overwrite mode */ + ControlStatus trans_fifo_order; /*!< transmit FIFO order */ + uint16_t prescaler; /*!< baudrate prescaler */ +} can_parameter_struct; + +/* CAN transmit message struct */ +typedef struct { + uint32_t tx_sfid; /*!< standard format frame identifier */ + uint32_t tx_efid; /*!< extended format frame identifier */ + uint8_t tx_ff; /*!< format of frame, standard or extended format */ + uint8_t tx_ft; /*!< type of frame, data or remote */ + uint8_t tx_dlen; /*!< data length */ + uint8_t tx_data[8]; /*!< transmit data */ +} can_trasnmit_message_struct; + +/* CAN receive message struct */ +typedef struct { + uint32_t rx_sfid; /*!< standard format frame identifier */ + uint32_t rx_efid; /*!< extended format frame identifier */ + uint8_t rx_ff; /*!< format of frame, standard or extended format */ + uint8_t rx_ft; /*!< type of frame, data or remote */ + uint8_t rx_dlen; /*!< data length */ + uint8_t rx_data[8]; /*!< receive data */ + uint8_t rx_fi; /*!< filtering index */ +} can_receive_message_struct; + +/* CAN filter parameters struct */ +typedef struct { + uint16_t filter_list_high; /*!< filter list number high bits*/ + uint16_t filter_list_low; /*!< filter list number low bits */ + uint16_t filter_mask_high; /*!< filter mask number high bits */ + uint16_t filter_mask_low; /*!< filter mask number low bits */ + uint16_t filter_fifo_number; /*!< receive FIFO associated with the filter */ + uint16_t filter_number; /*!< filter number */ + uint16_t filter_mode; /*!< filter mode, list or mask */ + uint16_t filter_bits; /*!< filter scale */ + ControlStatus filter_enable; /*!< filter work or not */ +} can_filter_parameter_struct; + +/* CAN errors */ +typedef enum { + CAN_ERROR_NONE = 0, /*!< no error */ + CAN_ERROR_FILL, /*!< fill error */ + CAN_ERROR_FORMATE, /*!< format error */ + CAN_ERROR_ACK, /*!< ACK error */ + CAN_ERROR_BITRECESSIVE, /*!< bit recessive error */ + CAN_ERROR_BITDOMINANTER, /*!< bit dominant error */ + CAN_ERROR_CRC, /*!< CRC error */ + CAN_ERROR_SOFTWARECFG, /*!< software configure */ +} can_error_enum; + +/* transmit states */ +typedef enum { + CAN_TRANSMIT_FAILED = 0, /*!< CAN transmitted failure */ + CAN_TRANSMIT_OK = 1, /*!< CAN transmitted success */ + CAN_TRANSMIT_PENDING = 2, /*!< CAN transmitted pending */ + CAN_TRANSMIT_NOMAILBOX = 4, /*!< no empty mailbox to be used for CAN */ +} can_transmit_state_enum; + +typedef enum { + CAN_INIT_STRUCT = 0, /* CAN initiliaze parameters struct */ + CAN_FILTER_STRUCT, /* CAN filter parameters struct */ + CAN_TX_MESSAGE_STRUCT, /* CAN transmit message struct */ + CAN_RX_MESSAGE_STRUCT, /* CAN receive message struct */ +} can_struct_type_enum; + +/* CAN baudrate prescaler*/ +#define BT_BAUDPSC(regval) (BITS(0,9) & ((uint32_t)(regval) << 0)) + +/* CAN bit segment 1*/ +#define BT_BS1(regval) (BITS(16,19) & ((uint32_t)(regval) << 16)) + +/* CAN bit segment 2*/ +#define BT_BS2(regval) (BITS(20,22) & ((uint32_t)(regval) << 20)) + +/* CAN resynchronization jump width*/ +#define BT_SJW(regval) (BITS(24,25) & ((uint32_t)(regval) << 24)) + +/* CAN communication mode*/ +#define BT_MODE(regval) (BITS(30,31) & ((uint32_t)(regval) << 30)) + +/* CAN FDATA high 16 bits */ +#define FDATA_MASK_HIGH(regval) (BITS(16,31) & ((uint32_t)(regval) << 16)) + +/* CAN FDATA low 16 bits */ +#define FDATA_MASK_LOW(regval) (BITS(0,15) & ((uint32_t)(regval) << 0)) + +/* CAN1 filter start bank_number*/ +#define FCTL_HBC1F(regval) (BITS(8,13) & ((uint32_t)(regval) << 8)) + +/* CAN transmit mailbox extended identifier*/ +#define TMI_EFID(regval) (BITS(3,31) & ((uint32_t)(regval) << 3)) + +/* CAN transmit mailbox standard identifier*/ +#define TMI_SFID(regval) (BITS(21,31) & ((uint32_t)(regval) << 21)) + +/* transmit data byte 0 */ +#define TMDATA0_DB0(regval) (BITS(0,7) & ((uint32_t)(regval) << 0)) + +/* transmit data byte 1 */ +#define TMDATA0_DB1(regval) (BITS(8,15) & ((uint32_t)(regval) << 8)) + +/* transmit data byte 2 */ +#define TMDATA0_DB2(regval) (BITS(16,23) & ((uint32_t)(regval) << 16)) + +/* transmit data byte 3 */ +#define TMDATA0_DB3(regval) (BITS(24,31) & ((uint32_t)(regval) << 24)) + +/* transmit data byte 4 */ +#define TMDATA1_DB4(regval) (BITS(0,7) & ((uint32_t)(regval) << 0)) + +/* transmit data byte 5 */ +#define TMDATA1_DB5(regval) (BITS(8,15) & ((uint32_t)(regval) << 8)) + +/* transmit data byte 6 */ +#define TMDATA1_DB6(regval) (BITS(16,23) & ((uint32_t)(regval) << 16)) + +/* transmit data byte 7 */ +#define TMDATA1_DB7(regval) (BITS(24,31) & ((uint32_t)(regval) << 24)) + +/* receive mailbox extended identifier*/ +#define GET_RFIFOMI_EFID(regval) GET_BITS((uint32_t)(regval), 3, 31) + +/* receive mailbox standrad identifier*/ +#define GET_RFIFOMI_SFID(regval) GET_BITS((uint32_t)(regval), 21, 31) + +/* receive data length */ +#define GET_RFIFOMP_DLENC(regval) GET_BITS((uint32_t)(regval), 0, 3) + +/* the index of the filter by which the frame is passed */ +#define GET_RFIFOMP_FI(regval) GET_BITS((uint32_t)(regval), 8, 15) + +/* receive data byte 0 */ +#define GET_RFIFOMDATA0_DB0(regval) GET_BITS((uint32_t)(regval), 0, 7) + +/* receive data byte 1 */ +#define GET_RFIFOMDATA0_DB1(regval) GET_BITS((uint32_t)(regval), 8, 15) + +/* receive data byte 2 */ +#define GET_RFIFOMDATA0_DB2(regval) GET_BITS((uint32_t)(regval), 16, 23) + +/* receive data byte 3 */ +#define GET_RFIFOMDATA0_DB3(regval) GET_BITS((uint32_t)(regval), 24, 31) + +/* receive data byte 4 */ +#define GET_RFIFOMDATA1_DB4(regval) GET_BITS((uint32_t)(regval), 0, 7) + +/* receive data byte 5 */ +#define GET_RFIFOMDATA1_DB5(regval) GET_BITS((uint32_t)(regval), 8, 15) + +/* receive data byte 6 */ +#define GET_RFIFOMDATA1_DB6(regval) GET_BITS((uint32_t)(regval), 16, 23) + +/* receive data byte 7 */ +#define GET_RFIFOMDATA1_DB7(regval) GET_BITS((uint32_t)(regval), 24, 31) + +/* error number */ +#define GET_ERR_ERRN(regval) GET_BITS((uint32_t)(regval), 4, 6) + +/* transmit error count */ +#define GET_ERR_TECNT(regval) GET_BITS((uint32_t)(regval), 16, 23) + +/* receive error count */ +#define GET_ERR_RECNT(regval) GET_BITS((uint32_t)(regval), 24, 31) + +/* CAN errors */ +#define ERR_ERRN(regval) (BITS(4,6) & ((uint32_t)(regval) << 4)) +#define CAN_ERRN_0 ERR_ERRN(0) /* no error */ +#define CAN_ERRN_1 ERR_ERRN(1) /*!< fill error */ +#define CAN_ERRN_2 ERR_ERRN(2) /*!< format error */ +#define CAN_ERRN_3 ERR_ERRN(3) /*!< ACK error */ +#define CAN_ERRN_4 ERR_ERRN(4) /*!< bit recessive error */ +#define CAN_ERRN_5 ERR_ERRN(5) /*!< bit dominant error */ +#define CAN_ERRN_6 ERR_ERRN(6) /*!< CRC error */ +#define CAN_ERRN_7 ERR_ERRN(7) /*!< software error */ + +#define CAN_STATE_PENDING ((uint32_t)0x00000000U) /*!< CAN pending */ + +/* CAN communication mode */ +#define CAN_NORMAL_MODE ((uint8_t)0x00U) /*!< normal communication mode */ +#define CAN_LOOPBACK_MODE ((uint8_t)0x01U) /*!< loopback communication mode */ +#define CAN_SILENT_MODE ((uint8_t)0x02U) /*!< silent communication mode */ +#define CAN_SILENT_LOOPBACK_MODE ((uint8_t)0x03U) /*!< loopback and silent communication mode */ + +/* CAN resynchronisation jump width */ +#define CAN_BT_SJW_1TQ ((uint8_t)0x00U) /*!< 1 time quanta */ +#define CAN_BT_SJW_2TQ ((uint8_t)0x01U) /*!< 2 time quanta */ +#define CAN_BT_SJW_3TQ ((uint8_t)0x02U) /*!< 3 time quanta */ +#define CAN_BT_SJW_4TQ ((uint8_t)0x03U) /*!< 4 time quanta */ + +/* CAN time segment 1 */ +#define CAN_BT_BS1_1TQ ((uint8_t)0x00U) /*!< 1 time quanta */ +#define CAN_BT_BS1_2TQ ((uint8_t)0x01U) /*!< 2 time quanta */ +#define CAN_BT_BS1_3TQ ((uint8_t)0x02U) /*!< 3 time quanta */ +#define CAN_BT_BS1_4TQ ((uint8_t)0x03U) /*!< 4 time quanta */ +#define CAN_BT_BS1_5TQ ((uint8_t)0x04U) /*!< 5 time quanta */ +#define CAN_BT_BS1_6TQ ((uint8_t)0x05U) /*!< 6 time quanta */ +#define CAN_BT_BS1_7TQ ((uint8_t)0x06U) /*!< 7 time quanta */ +#define CAN_BT_BS1_8TQ ((uint8_t)0x07U) /*!< 8 time quanta */ +#define CAN_BT_BS1_9TQ ((uint8_t)0x08U) /*!< 9 time quanta */ +#define CAN_BT_BS1_10TQ ((uint8_t)0x09U) /*!< 10 time quanta */ +#define CAN_BT_BS1_11TQ ((uint8_t)0x0AU) /*!< 11 time quanta */ +#define CAN_BT_BS1_12TQ ((uint8_t)0x0BU) /*!< 12 time quanta */ +#define CAN_BT_BS1_13TQ ((uint8_t)0x0CU) /*!< 13 time quanta */ +#define CAN_BT_BS1_14TQ ((uint8_t)0x0DU) /*!< 14 time quanta */ +#define CAN_BT_BS1_15TQ ((uint8_t)0x0EU) /*!< 15 time quanta */ +#define CAN_BT_BS1_16TQ ((uint8_t)0x0FU) /*!< 16 time quanta */ + +/* CAN time segment 2 */ +#define CAN_BT_BS2_1TQ ((uint8_t)0x00U) /*!< 1 time quanta */ +#define CAN_BT_BS2_2TQ ((uint8_t)0x01U) /*!< 2 time quanta */ +#define CAN_BT_BS2_3TQ ((uint8_t)0x02U) /*!< 3 time quanta */ +#define CAN_BT_BS2_4TQ ((uint8_t)0x03U) /*!< 4 time quanta */ +#define CAN_BT_BS2_5TQ ((uint8_t)0x04U) /*!< 5 time quanta */ +#define CAN_BT_BS2_6TQ ((uint8_t)0x05U) /*!< 6 time quanta */ +#define CAN_BT_BS2_7TQ ((uint8_t)0x06U) /*!< 7 time quanta */ +#define CAN_BT_BS2_8TQ ((uint8_t)0x07U) /*!< 8 time quanta */ + +/* CAN mailbox number */ +#define CAN_MAILBOX0 ((uint8_t)0x00U) /*!< mailbox0 */ +#define CAN_MAILBOX1 ((uint8_t)0x01U) /*!< mailbox1 */ +#define CAN_MAILBOX2 ((uint8_t)0x02U) /*!< mailbox2 */ +#define CAN_NOMAILBOX ((uint8_t)0x03U) /*!< no mailbox empty */ + +/* CAN frame format */ +#define CAN_FF_STANDARD ((uint32_t)0x00000000U) /*!< standard frame */ +#define CAN_FF_EXTENDED ((uint32_t)0x00000004U) /*!< extended frame */ + +/* CAN receive fifo */ +#define CAN_FIFO0 ((uint8_t)0x00U) /*!< receive FIFO0 */ +#define CAN_FIFO1 ((uint8_t)0x01U) /*!< receive FIFO1 */ + +/* frame number of receive fifo */ +#define CAN_RFIF_RFL_MASK ((uint32_t)0x00000003U) /*!< mask for frame number in receive FIFOx */ + +#define CAN_SFID_MASK ((uint32_t)0x000007FFU) /*!< mask of standard identifier */ +#define CAN_EFID_MASK ((uint32_t)0x1FFFFFFFU) /*!< mask of extended identifier */ + +/* CAN working mode */ +#define CAN_MODE_INITIALIZE ((uint8_t)0x01U) /*!< CAN initialize mode */ +#define CAN_MODE_NORMAL ((uint8_t)0x02U) /*!< CAN normal mode */ +#define CAN_MODE_SLEEP ((uint8_t)0x04U) /*!< CAN sleep mode */ + +/* filter bits */ +#define CAN_FILTERBITS_16BIT ((uint8_t)0x00U) /*!< CAN filter 16 bits */ +#define CAN_FILTERBITS_32BIT ((uint8_t)0x01U) /*!< CAN filter 32 bits */ + +/* filter mode */ +#define CAN_FILTERMODE_MASK ((uint8_t)0x00U) /*!< mask mode */ +#define CAN_FILTERMODE_LIST ((uint8_t)0x01U) /*!< list mode */ + +/* filter 16 bits mask */ +#define CAN_FILTER_MASK_16BITS ((uint32_t)0x0000FFFFU) /*!< can filter 16 bits mask */ + +/* frame type */ +#define CAN_FT_DATA ((uint32_t)0x00000000U) /*!< data frame */ +#define CAN_FT_REMOTE ((uint32_t)0x00000002U) /*!< remote frame */ + +/* CAN timeout */ +#define CAN_TIMEOUT ((uint32_t)0x0000FFFFU) /*!< timeout value */ + +/* interrupt enable bits */ +#define CAN_INT_TME CAN_INTEN_TMEIE /*!< transmit mailbox empty interrupt enable */ +#define CAN_INT_RFNE0 CAN_INTEN_RFNEIE0 /*!< receive FIFO0 not empty interrupt enable */ +#define CAN_INT_RFF0 CAN_INTEN_RFFIE0 /*!< receive FIFO0 full interrupt enable */ +#define CAN_INT_RFO0 CAN_INTEN_RFOIE0 /*!< receive FIFO0 overfull interrupt enable */ +#define CAN_INT_RFNE1 CAN_INTEN_RFNEIE1 /*!< receive FIFO1 not empty interrupt enable */ +#define CAN_INT_RFF1 CAN_INTEN_RFFIE1 /*!< receive FIFO1 full interrupt enable */ +#define CAN_INT_RFO1 CAN_INTEN_RFOIE1 /*!< receive FIFO1 overfull interrupt enable */ +#define CAN_INT_WERR CAN_INTEN_WERRIE /*!< warning error interrupt enable */ +#define CAN_INT_PERR CAN_INTEN_PERRIE /*!< passive error interrupt enable */ +#define CAN_INT_BO CAN_INTEN_BOIE /*!< bus-off interrupt enable */ +#define CAN_INT_ERRN CAN_INTEN_ERRNIE /*!< error number interrupt enable */ +#define CAN_INT_ERR CAN_INTEN_ERRIE /*!< error interrupt enable */ +#define CAN_INT_WAKEUP CAN_INTEN_WIE /*!< wakeup interrupt enable */ +#define CAN_INT_SLPW CAN_INTEN_SLPWIE /*!< sleep working interrupt enable */ + +/* function declarations */ +/* deinitialize CAN */ +void can_deinit(uint32_t can_periph); +/* initialize CAN struct */ +void can_struct_para_init(can_struct_type_enum type, void* p_struct); +/* initialize CAN */ +ErrStatus can_init(uint32_t can_periph, + can_parameter_struct* can_parameter_init); +/* CAN filter init */ +void can_filter_init(can_filter_parameter_struct* can_filter_parameter_init); +/* set can1 fliter start bank number */ +void can1_filter_start_bank(uint8_t start_bank); +/* enable functions */ +/* CAN debug freeze enable */ +void can_debug_freeze_enable(uint32_t can_periph); +/* CAN debug freeze disable */ +void can_debug_freeze_disable(uint32_t can_periph); +/* CAN time trigger mode enable */ +void can_time_trigger_mode_enable(uint32_t can_periph); +/* CAN time trigger mode disable */ +void can_time_trigger_mode_disable(uint32_t can_periph); + +/* transmit functions */ +/* transmit CAN message */ +uint8_t can_message_transmit(uint32_t can_periph, + can_trasnmit_message_struct* transmit_message); +/* get CAN transmit state */ +can_transmit_state_enum can_transmit_states(uint32_t can_periph, + uint8_t mailbox_number); +/* stop CAN transmission */ +void can_transmission_stop(uint32_t can_periph, uint8_t mailbox_number); +/* CAN receive message */ +void can_message_receive(uint32_t can_periph, uint8_t fifo_number, + can_receive_message_struct* receive_message); +/* CAN release fifo */ +void can_fifo_release(uint32_t can_periph, uint8_t fifo_number); +/* CAN receive message length */ +uint8_t can_receive_message_length_get(uint32_t can_periph, uint8_t fifo_number); +/* CAN working mode */ +ErrStatus can_working_mode_set(uint32_t can_periph, uint8_t working_mode); +/* CAN wakeup from sleep mode */ +ErrStatus can_wakeup(uint32_t can_periph); + +/* CAN get error */ +can_error_enum can_error_get(uint32_t can_periph); +/* get CAN receive error number */ +uint8_t can_receive_error_number_get(uint32_t can_periph); +/* get CAN transmit error number */ +uint8_t can_transmit_error_number_get(uint32_t can_periph); + +/* CAN interrupt enable */ +void can_interrupt_enable(uint32_t can_periph, uint32_t interrupt); +/* CAN interrupt disable */ +void can_interrupt_disable(uint32_t can_periph, uint32_t interrupt); +/* CAN get flag state */ +FlagStatus can_flag_get(uint32_t can_periph, can_flag_enum flag); +/* CAN clear flag state */ +void can_flag_clear(uint32_t can_periph, can_flag_enum flag); +/* CAN get interrupt flag state */ +FlagStatus can_interrupt_flag_get(uint32_t can_periph, + can_interrupt_flag_enum flag); +/* CAN clear interrupt flag state */ +void can_interrupt_flag_clear(uint32_t can_periph, can_interrupt_flag_enum flag); + +#endif /* GD32VF103_CAN_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_crc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_crc.h new file mode 100644 index 00000000..d9ae2662 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_crc.h @@ -0,0 +1,80 @@ +/*! + \file gd32vf103_crc.h + \brief definitions for the CRC + + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_CRC_H +#define GD32VF103_CRC_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* CRC definitions */ +#define CRC CRC_BASE + +/* registers definitions */ +#define CRC_DATA REG32(CRC + 0x00U) /*!< CRC data register */ +#define CRC_FDATA REG32(CRC + 0x04U) /*!< CRC free data register */ +#define CRC_CTL REG32(CRC + 0x08U) /*!< CRC control register */ + +/* bits definitions */ +/* CRC_DATA */ +#define CRC_DATA_DATA BITS(0, 31) /*!< CRC calculation result bits */ + +/* CRC_FDATA */ +#define CRC_FDATA_FDATA BITS(0, 7) /*!< CRC free data bits */ + +/* CRC_CTL */ +#define CRC_CTL_RST BIT(0) /*!< CRC reset CRC_DATA register bit */ + +/* function declarations */ +/* deinit CRC calculation unit */ +void crc_deinit(void); + +/* reset data register(CRC_DATA) to the value of 0xFFFFFFFF */ +void crc_data_register_reset(void); +/* read the value of the data register */ +uint32_t crc_data_register_read(void); + +/* read the value of the free data register */ +uint8_t crc_free_data_register_read(void); +/* write data to the free data register */ +void crc_free_data_register_write(uint8_t free_data); + +/* calculate the CRC value of a 32-bit data */ +uint32_t crc_single_data_calculate(uint32_t sdata); +/* calculate the CRC value of an array of 32-bit values */ +uint32_t crc_block_data_calculate(uint32_t array[], uint32_t size); + +#endif /* GD32VF103_CRC_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dac.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dac.h new file mode 100644 index 00000000..a249b689 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dac.h @@ -0,0 +1,244 @@ +/*! + \file gd32vf103_dac.h + \brief definitions for the DAC + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_DAC_H +#define GD32VF103_DAC_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* DACx(x=0,1) definitions */ +#define DAC DAC_BASE +#define DAC0 (0U) +#define DAC1 (1U) + +/* registers definitions */ +#define DAC_CTL REG32(DAC + 0x00U) /*!< DAC control register */ +#define DAC_SWT REG32(DAC + 0x04U) /*!< DAC software trigger register */ +#define DAC0_R12DH REG32(DAC + 0x08U) /*!< DAC0 12-bit right-aligned data holding register */ +#define DAC0_L12DH REG32(DAC + 0x0CU) /*!< DAC0 12-bit left-aligned data holding register */ +#define DAC0_R8DH REG32(DAC + 0x10U) /*!< DAC0 8-bit right-aligned data holding register */ +#define DAC1_R12DH REG32(DAC + 0x14U) /*!< DAC1 12-bit right-aligned data holding register */ +#define DAC1_L12DH REG32(DAC + 0x18U) /*!< DAC1 12-bit left-aligned data holding register */ +#define DAC1_R8DH REG32(DAC + 0x1CU) /*!< DAC1 8-bit right-aligned data holding register */ +#define DACC_R12DH REG32(DAC + 0x20U) /*!< DAC concurrent mode 12-bit right-aligned data holding register */ +#define DACC_L12DH REG32(DAC + 0x24U) /*!< DAC concurrent mode 12-bit left-aligned data holding register */ +#define DACC_R8DH REG32(DAC + 0x28U) /*!< DAC concurrent mode 8-bit right-aligned data holding register */ +#define DAC0_DO REG32(DAC + 0x2CU) /*!< DAC0 data output register */ +#define DAC1_DO REG32(DAC + 0x30U) /*!< DAC1 data output register */ + +/* bits definitions */ +/* DAC_CTL */ +#define DAC_CTL_DEN0 BIT(0) /*!< DAC0 enable/disable bit */ +#define DAC_CTL_DBOFF0 BIT(1) /*!< DAC0 output buffer turn on/turn off bit */ +#define DAC_CTL_DTEN0 BIT(2) /*!< DAC0 trigger enable/disable bit */ +#define DAC_CTL_DTSEL0 BITS(3,5) /*!< DAC0 trigger source selection enable/disable bits */ +#define DAC_CTL_DWM0 BITS(6,7) /*!< DAC0 noise wave mode */ +#define DAC_CTL_DWBW0 BITS(8,11) /*!< DAC0 noise wave bit width */ +#define DAC_CTL_DDMAEN0 BIT(12) /*!< DAC0 DMA enable/disable bit */ +#define DAC_CTL_DEN1 BIT(16) /*!< DAC1 enable/disable bit */ +#define DAC_CTL_DBOFF1 BIT(17) /*!< DAC1 output buffer turn on/turn off bit */ +#define DAC_CTL_DTEN1 BIT(18) /*!< DAC1 trigger enable/disable bit */ +#define DAC_CTL_DTSEL1 BITS(19,21) /*!< DAC1 trigger source selection enable/disable bits */ +#define DAC_CTL_DWM1 BITS(22,23) /*!< DAC1 noise wave mode */ +#define DAC_CTL_DWBW1 BITS(24,27) /*!< DAC1 noise wave bit width */ +#define DAC_CTL_DDMAEN1 BIT(28) /*!< DAC1 DMA enable/disable bit */ + +/* DAC_SWT */ +#define DAC_SWT_SWTR0 BIT(0) /*!< DAC0 software trigger bit, cleared by hardware */ +#define DAC_SWT_SWTR1 BIT(1) /*!< DAC1 software trigger bit, cleared by hardware */ + +/* DAC0_R12DH */ +#define DAC0_R12DH_DAC0_DH BITS(0,11) /*!< DAC0 12-bit right-aligned data bits */ + +/* DAC0_L12DH */ +#define DAC0_L12DH_DAC0_DH BITS(4,15) /*!< DAC0 12-bit left-aligned data bits */ + +/* DAC0_R8DH */ +#define DAC0_R8DH_DAC0_DH BITS(0,7) /*!< DAC0 8-bit right-aligned data bits */ + +/* DAC1_R12DH */ +#define DAC1_R12DH_DAC1_DH BITS(0,11) /*!< DAC1 12-bit right-aligned data bits */ + +/* DAC1_L12DH */ +#define DAC1_L12DH_DAC1_DH BITS(4,15) /*!< DAC1 12-bit left-aligned data bits */ + +/* DAC1_R8DH */ +#define DAC1_R8DH_DAC1_DH BITS(0,7) /*!< DAC1 8-bit right-aligned data bits */ + +/* DACC_R12DH */ +#define DACC_R12DH_DAC0_DH BITS(0,11) /*!< DAC concurrent mode DAC0 12-bit right-aligned data bits */ +#define DACC_R12DH_DAC1_DH BITS(16,27) /*!< DAC concurrent mode DAC1 12-bit right-aligned data bits */ + +/* DACC_L12DH */ +#define DACC_L12DH_DAC0_DH BITS(4,15) /*!< DAC concurrent mode DAC0 12-bit left-aligned data bits */ +#define DACC_L12DH_DAC1_DH BITS(20,31) /*!< DAC concurrent mode DAC1 12-bit left-aligned data bits */ + +/* DACC_R8DH */ +#define DACC_R8DH_DAC0_DH BITS(0,7) /*!< DAC concurrent mode DAC0 8-bit right-aligned data bits */ +#define DACC_R8DH_DAC1_DH BITS(8,15) /*!< DAC concurrent mode DAC1 8-bit right-aligned data bits */ + +/* DAC0_DO */ +#define DAC0_DO_DAC0_DO BITS(0,11) /*!< DAC0 12-bit output data bits */ + +/* DAC1_DO */ +#define DAC1_DO_DAC1_DO BITS(0,11) /*!< DAC1 12-bit output data bits */ + +/* constants definitions */ +/* DAC trigger source */ +#define CTL_DTSEL(regval) (BITS(3,5) & ((uint32_t)(regval) << 3)) +#define DAC_TRIGGER_T5_TRGO CTL_DTSEL(0) /*!< TIMER5 TRGO */ +#define DAC_TRIGGER_T2_TRGO CTL_DTSEL(1) /*!< TIMER2 TRGO */ +#define DAC_TRIGGER_T6_TRGO CTL_DTSEL(2) /*!< TIMER6 TRGO */ +#define DAC_TRIGGER_T4_TRGO CTL_DTSEL(3) /*!< TIMER4 TRGO */ +#define DAC_TRIGGER_T1_TRGO CTL_DTSEL(4) /*!< TIMER1 TRGO */ +#define DAC_TRIGGER_T3_TRGO CTL_DTSEL(5) /*!< TIMER3 TRGO */ +#define DAC_TRIGGER_EXTI_9 CTL_DTSEL(6) /*!< EXTI interrupt line9 event */ +#define DAC_TRIGGER_SOFTWARE CTL_DTSEL(7) /*!< software trigger */ + +/* DAC noise wave mode */ +#define CTL_DWM(regval) (BITS(6,7) & ((uint32_t)(regval) << 6)) +#define DAC_WAVE_DISABLE CTL_DWM(0) /*!< wave disable */ +#define DAC_WAVE_MODE_LFSR CTL_DWM(1) /*!< LFSR noise mode */ +#define DAC_WAVE_MODE_TRIANGLE CTL_DWM(2) /*!< triangle noise mode */ + +/* DAC noise wave bit width */ +#define DWBW(regval) (BITS(8,11) & ((uint32_t)(regval) << 8)) +#define DAC_WAVE_BIT_WIDTH_1 DWBW(0) /*!< bit width of the wave signal is 1 */ +#define DAC_WAVE_BIT_WIDTH_2 DWBW(1) /*!< bit width of the wave signal is 2 */ +#define DAC_WAVE_BIT_WIDTH_3 DWBW(2) /*!< bit width of the wave signal is 3 */ +#define DAC_WAVE_BIT_WIDTH_4 DWBW(3) /*!< bit width of the wave signal is 4 */ +#define DAC_WAVE_BIT_WIDTH_5 DWBW(4) /*!< bit width of the wave signal is 5 */ +#define DAC_WAVE_BIT_WIDTH_6 DWBW(5) /*!< bit width of the wave signal is 6 */ +#define DAC_WAVE_BIT_WIDTH_7 DWBW(6) /*!< bit width of the wave signal is 7 */ +#define DAC_WAVE_BIT_WIDTH_8 DWBW(7) /*!< bit width of the wave signal is 8 */ +#define DAC_WAVE_BIT_WIDTH_9 DWBW(8) /*!< bit width of the wave signal is 9 */ +#define DAC_WAVE_BIT_WIDTH_10 DWBW(9) /*!< bit width of the wave signal is 10 */ +#define DAC_WAVE_BIT_WIDTH_11 DWBW(10) /*!< bit width of the wave signal is 11 */ +#define DAC_WAVE_BIT_WIDTH_12 DWBW(11) /*!< bit width of the wave signal is 12 */ + +/* unmask LFSR bits in DAC LFSR noise mode */ +#define DAC_LFSR_BIT0 DAC_WAVE_BIT_WIDTH_1 /*!< unmask the LFSR bit0 */ +#define DAC_LFSR_BITS1_0 DAC_WAVE_BIT_WIDTH_2 /*!< unmask the LFSR bits[1:0] */ +#define DAC_LFSR_BITS2_0 DAC_WAVE_BIT_WIDTH_3 /*!< unmask the LFSR bits[2:0] */ +#define DAC_LFSR_BITS3_0 DAC_WAVE_BIT_WIDTH_4 /*!< unmask the LFSR bits[3:0] */ +#define DAC_LFSR_BITS4_0 DAC_WAVE_BIT_WIDTH_5 /*!< unmask the LFSR bits[4:0] */ +#define DAC_LFSR_BITS5_0 DAC_WAVE_BIT_WIDTH_6 /*!< unmask the LFSR bits[5:0] */ +#define DAC_LFSR_BITS6_0 DAC_WAVE_BIT_WIDTH_7 /*!< unmask the LFSR bits[6:0] */ +#define DAC_LFSR_BITS7_0 DAC_WAVE_BIT_WIDTH_8 /*!< unmask the LFSR bits[7:0] */ +#define DAC_LFSR_BITS8_0 DAC_WAVE_BIT_WIDTH_9 /*!< unmask the LFSR bits[8:0] */ +#define DAC_LFSR_BITS9_0 DAC_WAVE_BIT_WIDTH_10 /*!< unmask the LFSR bits[9:0] */ +#define DAC_LFSR_BITS10_0 DAC_WAVE_BIT_WIDTH_11 /*!< unmask the LFSR bits[10:0] */ +#define DAC_LFSR_BITS11_0 DAC_WAVE_BIT_WIDTH_12 /*!< unmask the LFSR bits[11:0] */ + +/* DAC data alignment */ +#define DATA_ALIGN(regval) (BITS(0,1) & ((uint32_t)(regval) << 0)) +#define DAC_ALIGN_12B_R DATA_ALIGN(0) /*!< data right 12b alignment */ +#define DAC_ALIGN_12B_L DATA_ALIGN(1) /*!< data left 12b alignment */ +#define DAC_ALIGN_8B_R DATA_ALIGN(2) /*!< data right 8b alignment */ +/* triangle amplitude in DAC triangle noise mode */ +#define DAC_TRIANGLE_AMPLITUDE_1 DAC_WAVE_BIT_WIDTH_1 /*!< triangle amplitude is 1 */ +#define DAC_TRIANGLE_AMPLITUDE_3 DAC_WAVE_BIT_WIDTH_2 /*!< triangle amplitude is 3 */ +#define DAC_TRIANGLE_AMPLITUDE_7 DAC_WAVE_BIT_WIDTH_3 /*!< triangle amplitude is 7 */ +#define DAC_TRIANGLE_AMPLITUDE_15 DAC_WAVE_BIT_WIDTH_4 /*!< triangle amplitude is 15 */ +#define DAC_TRIANGLE_AMPLITUDE_31 DAC_WAVE_BIT_WIDTH_5 /*!< triangle amplitude is 31 */ +#define DAC_TRIANGLE_AMPLITUDE_63 DAC_WAVE_BIT_WIDTH_6 /*!< triangle amplitude is 63 */ +#define DAC_TRIANGLE_AMPLITUDE_127 DAC_WAVE_BIT_WIDTH_7 /*!< triangle amplitude is 127 */ +#define DAC_TRIANGLE_AMPLITUDE_255 DAC_WAVE_BIT_WIDTH_8 /*!< triangle amplitude is 255 */ +#define DAC_TRIANGLE_AMPLITUDE_511 DAC_WAVE_BIT_WIDTH_9 /*!< triangle amplitude is 511 */ +#define DAC_TRIANGLE_AMPLITUDE_1023 DAC_WAVE_BIT_WIDTH_10 /*!< triangle amplitude is 1023 */ +#define DAC_TRIANGLE_AMPLITUDE_2047 DAC_WAVE_BIT_WIDTH_11 /*!< triangle amplitude is 2047 */ +#define DAC_TRIANGLE_AMPLITUDE_4095 DAC_WAVE_BIT_WIDTH_12 /*!< triangle amplitude is 4095 */ + +/* function declarations */ +/* initialization functions */ +/* deinitialize DAC */ +void dac_deinit(void); +/* enable DAC */ +void dac_enable(uint32_t dac_periph); +/* disable DAC */ +void dac_disable(uint32_t dac_periph); +/* enable DAC DMA */ +void dac_dma_enable(uint32_t dac_periph); +/* disable DAC DMA */ +void dac_dma_disable(uint32_t dac_periph); +/* enable DAC output buffer */ +void dac_output_buffer_enable(uint32_t dac_periph); +/* disable DAC output buffer */ +void dac_output_buffer_disable(uint32_t dac_periph); +/* get the last data output value */ +uint16_t dac_output_value_get(uint32_t dac_periph); +/* set DAC data holding register value */ +void dac_data_set(uint32_t dac_periph, uint32_t dac_align, uint16_t data); + +/* DAC trigger configuration */ +/* enable DAC trigger */ +void dac_trigger_enable(uint32_t dac_periph); +/* disable DAC trigger */ +void dac_trigger_disable(uint32_t dac_periph); +/* configure DAC trigger source */ +void dac_trigger_source_config(uint32_t dac_periph, uint32_t triggersource); +/* enable DAC software trigger */ +void dac_software_trigger_enable(uint32_t dac_periph); +/* disable DAC software trigger */ +void dac_software_trigger_disable(uint32_t dac_periph); + +/* DAC wave mode configuration */ +/* configure DAC wave mode */ +void dac_wave_mode_config(uint32_t dac_periph, uint32_t wave_mode); +/* configure DAC wave bit width */ +void dac_wave_bit_width_config(uint32_t dac_periph, uint32_t bit_width); +/* configure DAC LFSR noise mode */ +void dac_lfsr_noise_config(uint32_t dac_periph, uint32_t unmask_bits); +/* configure DAC triangle noise mode */ +void dac_triangle_noise_config(uint32_t dac_periph, uint32_t amplitude); + +/* DAC concurrent mode configuration */ +/* enable DAC concurrent mode */ +void dac_concurrent_enable(void); +/* disable DAC concurrent mode */ +void dac_concurrent_disable(void); +/* enable DAC concurrent software trigger */ +void dac_concurrent_software_trigger_enable(void); +/* disable DAC concurrent software trigger */ +void dac_concurrent_software_trigger_disable(void); +/* enable DAC concurrent buffer function */ +void dac_concurrent_output_buffer_enable(void); +/* disable DAC concurrent buffer function */ +void dac_concurrent_output_buffer_disable(void); +/* set DAC concurrent mode data holding register value */ +void dac_concurrent_data_set(uint32_t dac_align, uint16_t data0, uint16_t data1); + +#endif /* GD32VF103_DAC_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dbg.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dbg.h new file mode 100644 index 00000000..590cc9be --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dbg.h @@ -0,0 +1,111 @@ +/*! + \file gd32vf103_dbg.h + \brief definitions for the DBG + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_DBG_H +#define GD32VF103_DBG_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" + + +/* DBG definitions */ +#define DBG DBG_BASE + +/* registers definitions */ +#define DBG_ID REG32(DBG + 0x00U) /*!< DBG_ID code register */ +#define DBG_CTL REG32(DBG + 0x04U) /*!< DBG control register */ + +/* bits definitions */ +/* DBG_ID */ +#define DBG_ID_ID_CODE BITS(0,31) /*!< DBG ID code values */ + +/* DBG_CTL */ +#define DBG_CTL_SLP_HOLD BIT(0) /*!< keep debugger connection during sleep mode */ +#define DBG_CTL_DSLP_HOLD BIT(1) /*!< keep debugger connection during deepsleep mode */ +#define DBG_CTL_STB_HOLD BIT(2) /*!< keep debugger connection during standby mode */ +#define DBG_CTL_FWDGT_HOLD BIT(8) /*!< debug FWDGT kept when core is halted */ +#define DBG_CTL_WWDGT_HOLD BIT(9) /*!< debug WWDGT kept when core is halted */ +#define DBG_CTL_TIMER0_HOLD BIT(10) /*!< hold TIMER0 counter when core is halted */ +#define DBG_CTL_TIMER1_HOLD BIT(11) /*!< hold TIMER1 counter when core is halted */ +#define DBG_CTL_TIMER2_HOLD BIT(12) /*!< hold TIMER2 counter when core is halted */ +#define DBG_CTL_TIMER3_HOLD BIT(13) /*!< hold TIMER3 counter when core is halted */ +#define DBG_CTL_CAN0_HOLD BIT(14) /*!< debug CAN0 kept when core is halted */ +#define DBG_CTL_I2C0_HOLD BIT(15) /*!< hold I2C0 smbus when core is halted */ +#define DBG_CTL_I2C1_HOLD BIT(16) /*!< hold I2C1 smbus when core is halted */ +#define DBG_CTL_TIMER4_HOLD BIT(18) /*!< hold TIMER4 counter when core is halted */ +#define DBG_CTL_TIMER5_HOLD BIT(19) /*!< hold TIMER5 counter when core is halted */ +#define DBG_CTL_TIMER6_HOLD BIT(20) /*!< hold TIMER6 counter when core is halted */ +#define DBG_CTL_CAN1_HOLD BIT(21) /*!< debug CAN1 kept when core is halted */ + +/* constants definitions */ +/* debug hold when core is halted */ +typedef enum +{ + DBG_FWDGT_HOLD = BIT(8), /*!< debug FWDGT kept when core is halted */ + DBG_WWDGT_HOLD = BIT(9), /*!< debug WWDGT kept when core is halted */ + DBG_TIMER0_HOLD = BIT(10), /*!< hold TIMER0 counter when core is halted */ + DBG_TIMER1_HOLD = BIT(11), /*!< hold TIMER1 counter when core is halted */ + DBG_TIMER2_HOLD = BIT(12), /*!< hold TIMER2 counter when core is halted */ + DBG_TIMER3_HOLD = BIT(13), /*!< hold TIMER3 counter when core is halted */ + DBG_CAN0_HOLD = BIT(14), /*!< debug CAN0 kept when core is halted */ + DBG_I2C0_HOLD = BIT(15), /*!< hold I2C0 smbus when core is halted */ + DBG_I2C1_HOLD = BIT(16), /*!< hold I2C1 smbus when core is halted */ + DBG_TIMER4_HOLD = BIT(17), /*!< hold TIMER4 counter when core is halted */ + DBG_TIMER5_HOLD = BIT(18), /*!< hold TIMER5 counter when core is halted */ + DBG_TIMER6_HOLD = BIT(19), /*!< hold TIMER6 counter when core is halted */ + DBG_CAN1_HOLD = BIT(21), /*!< debug CAN1 kept when core is halted */ +}dbg_periph_enum; + +/* DBG low power mode configurations */ +#define DBG_LOW_POWER_SLEEP DBG_CTL_SLP_HOLD /*!< keep debugger connection during sleep mode */ +#define DBG_LOW_POWER_DEEPSLEEP DBG_CTL_DSLP_HOLD /*!< keep debugger connection during deepsleep mode */ +#define DBG_LOW_POWER_STANDBY DBG_CTL_STB_HOLD /*!< keep debugger connection during standby mode */ + +/* function declarations */ +/* read DBG_ID code register */ +uint32_t dbg_id_get(void); + +/* low power behavior configuration */ +/* enable low power behavior when the MCU is in debug mode */ +void dbg_low_power_enable(uint32_t dbg_low_power); +/* disable low power behavior when the MCU is in debug mode */ +void dbg_low_power_disable(uint32_t dbg_low_power); + +/* peripheral behavior configuration */ +/* enable peripheral behavior when the MCU is in debug mode */ +void dbg_periph_enable(dbg_periph_enum dbg_periph); +/* disable peripheral behavior when the MCU is in debug mode */ +void dbg_periph_disable(dbg_periph_enum dbg_periph); + +#endif /* GD32VF103_DBG_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dma.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dma.h new file mode 100644 index 00000000..93922788 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_dma.h @@ -0,0 +1,285 @@ +/*! + \file gd32vf103_dma.h + \brief definitions for the DMA + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_DMA_H +#define GD32VF103_DMA_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + + +/* DMA definitions */ +#define DMA0 (DMA_BASE) /*!< DMA0 base address */ +#define DMA1 (DMA_BASE + 0x0400U) /*!< DMA1 base address */ + +/* registers definitions */ +#define DMA_INTF(dmax) REG32((dmax) + 0x00U) /*!< DMA interrupt flag register */ +#define DMA_INTC(dmax) REG32((dmax) + 0x04U) /*!< DMA interrupt flag clear register */ + +#define DMA_CH0CTL(dmax) REG32((dmax) + 0x08U) /*!< DMA channel 0 control register */ +#define DMA_CH0CNT(dmax) REG32((dmax) + 0x0CU) /*!< DMA channel 0 counter register */ +#define DMA_CH0PADDR(dmax) REG32((dmax) + 0x10U) /*!< DMA channel 0 peripheral base address register */ +#define DMA_CH0MADDR(dmax) REG32((dmax) + 0x14U) /*!< DMA channel 0 memory base address register */ + +#define DMA_CH1CTL(dmax) REG32((dmax) + 0x1CU) /*!< DMA channel 1 control register */ +#define DMA_CH1CNT(dmax) REG32((dmax) + 0x20U) /*!< DMA channel 1 counter register */ +#define DMA_CH1PADDR(dmax) REG32((dmax) + 0x24U) /*!< DMA channel 1 peripheral base address register */ +#define DMA_CH1MADDR(dmax) REG32((dmax) + 0x28U) /*!< DMA channel 1 memory base address register */ + +#define DMA_CH2CTL(dmax) REG32((dmax) + 0x30U) /*!< DMA channel 2 control register */ +#define DMA_CH2CNT(dmax) REG32((dmax) + 0x34U) /*!< DMA channel 2 counter register */ +#define DMA_CH2PADDR(dmax) REG32((dmax) + 0x38U) /*!< DMA channel 2 peripheral base address register */ +#define DMA_CH2MADDR(dmax) REG32((dmax) + 0x3CU) /*!< DMA channel 2 memory base address register */ + +#define DMA_CH3CTL(dmax) REG32((dmax) + 0x44U) /*!< DMA channel 3 control register */ +#define DMA_CH3CNT(dmax) REG32((dmax) + 0x48U) /*!< DMA channel 3 counter register */ +#define DMA_CH3PADDR(dmax) REG32((dmax) + 0x4CU) /*!< DMA channel 3 peripheral base address register */ +#define DMA_CH3MADDR(dmax) REG32((dmax) + 0x50U) /*!< DMA channel 3 memory base address register */ + +#define DMA_CH4CTL(dmax) REG32((dmax) + 0x58U) /*!< DMA channel 4 control register */ +#define DMA_CH4CNT(dmax) REG32((dmax) + 0x5CU) /*!< DMA channel 4 counter register */ +#define DMA_CH4PADDR(dmax) REG32((dmax) + 0x60U) /*!< DMA channel 4 peripheral base address register */ +#define DMA_CH4MADDR(dmax) REG32((dmax) + 0x64U) /*!< DMA channel 4 memory base address register */ + +#define DMA_CH5CTL(dmax) REG32((dmax) + 0x6CU) /*!< DMA channel 5 control register */ +#define DMA_CH5CNT(dmax) REG32((dmax) + 0x70U) /*!< DMA channel 5 counter register */ +#define DMA_CH5PADDR(dmax) REG32((dmax) + 0x74U) /*!< DMA channel 5 peripheral base address register */ +#define DMA_CH5MADDR(dmax) REG32((dmax) + 0x78U) /*!< DMA channel 5 memory base address register */ + +#define DMA_CH6CTL(dmax) REG32((dmax) + 0x80U) /*!< DMA channel 6 control register */ +#define DMA_CH6CNT(dmax) REG32((dmax) + 0x84U) /*!< DMA channel 6 counter register */ +#define DMA_CH6PADDR(dmax) REG32((dmax) + 0x88U) /*!< DMA channel 6 peripheral base address register */ +#define DMA_CH6MADDR(dmax) REG32((dmax) + 0x8CU) /*!< DMA channel 6 memory base address register */ + +/* bits definitions */ +/* DMA_INTF */ +#define DMA_INTF_GIF BIT(0) /*!< global interrupt flag of channel */ +#define DMA_INTF_FTFIF BIT(1) /*!< full transfer finish flag of channel */ +#define DMA_INTF_HTFIF BIT(2) /*!< half transfer finish flag of channel */ +#define DMA_INTF_ERRIF BIT(3) /*!< error flag of channel */ + +/* DMA_INTC */ +#define DMA_INTC_GIFC BIT(0) /*!< clear global interrupt flag of channel */ +#define DMA_INTC_FTFIFC BIT(1) /*!< clear transfer finish flag of channel */ +#define DMA_INTC_HTFIFC BIT(2) /*!< clear half transfer finish flag of channel */ +#define DMA_INTC_ERRIFC BIT(3) /*!< clear error flag of channel */ + +/* DMA_CHxCTL, x=0..6 */ +#define DMA_CHXCTL_CHEN BIT(0) /*!< channel enable */ +#define DMA_CHXCTL_FTFIE BIT(1) /*!< enable bit for channel full transfer finish interrupt */ +#define DMA_CHXCTL_HTFIE BIT(2) /*!< enable bit for channel half transfer finish interrupt */ +#define DMA_CHXCTL_ERRIE BIT(3) /*!< enable bit for channel error interrupt */ +#define DMA_CHXCTL_DIR BIT(4) /*!< transfer direction */ +#define DMA_CHXCTL_CMEN BIT(5) /*!< circular mode enable */ +#define DMA_CHXCTL_PNAGA BIT(6) /*!< next address generation algorithm of peripheral */ +#define DMA_CHXCTL_MNAGA BIT(7) /*!< next address generation algorithm of memory */ +#define DMA_CHXCTL_PWIDTH BITS(8,9) /*!< transfer data width of peripheral */ +#define DMA_CHXCTL_MWIDTH BITS(10,11) /*!< transfer data width of memory */ +#define DMA_CHXCTL_PRIO BITS(12,13) /*!< priority level */ +#define DMA_CHXCTL_M2M BIT(14) /*!< memory to memory mode */ + +/* DMA_CHxCNT, x=0..6 */ +#define DMA_CHXCNT_CNT BITS(0,15) /*!< transfer counter */ + +/* DMA_CHxPADDR, x=0..6 */ +#define DMA_CHXPADDR_PADDR BITS(0,31) /*!< peripheral base address */ + +/* DMA_CHxMADDR, x=0..6 */ +#define DMA_CHXMADDR_MADDR BITS(0,31) /*!< memory base address */ + +/* constants definitions */ +/* DMA channel select */ +typedef enum +{ + DMA_CH0 = 0, /*!< DMA Channel0 */ + DMA_CH1, /*!< DMA Channel1 */ + DMA_CH2, /*!< DMA Channel2 */ + DMA_CH3, /*!< DMA Channel3 */ + DMA_CH4, /*!< DMA Channel4 */ + DMA_CH5, /*!< DMA Channel5 */ + DMA_CH6 /*!< DMA Channel6 */ +} dma_channel_enum; + +/* DMA initialize struct */ +typedef struct +{ + uint32_t periph_addr; /*!< peripheral base address */ + uint32_t periph_width; /*!< transfer data size of peripheral */ + uint32_t memory_addr; /*!< memory base address */ + uint32_t memory_width; /*!< transfer data size of memory */ + uint32_t number; /*!< channel transfer number */ + uint32_t priority; /*!< channel priority level */ + uint8_t periph_inc; /*!< peripheral increasing mode */ + uint8_t memory_inc; /*!< memory increasing mode */ + uint8_t direction; /*!< channel data transfer direction */ + +} dma_parameter_struct; + +#define DMA_FLAG_ADD(flag, shift) ((flag) << ((shift) * 4U)) /*!< DMA channel flag shift */ + +/* DMA_register address */ +#define DMA_CHCTL(dma, channel) REG32(((dma) + 0x08U) + 0x14U * (uint32_t)(channel)) /*!< the address of DMA channel CHXCTL register */ +#define DMA_CHCNT(dma, channel) REG32(((dma) + 0x0CU) + 0x14U * (uint32_t)(channel)) /*!< the address of DMA channel CHXCNT register */ +#define DMA_CHPADDR(dma, channel) REG32(((dma) + 0x10U) + 0x14U * (uint32_t)(channel)) /*!< the address of DMA channel CHXPADDR register */ +#define DMA_CHMADDR(dma, channel) REG32(((dma) + 0x14U) + 0x14U * (uint32_t)(channel)) /*!< the address of DMA channel CHXMADDR register */ + +/* DMA reset value */ +#define DMA_CHCTL_RESET_VALUE ((uint32_t)0x00000000U) /*!< the reset value of DMA channel CHXCTL register */ +#define DMA_CHCNT_RESET_VALUE ((uint32_t)0x00000000U) /*!< the reset value of DMA channel CHXCNT register */ +#define DMA_CHPADDR_RESET_VALUE ((uint32_t)0x00000000U) /*!< the reset value of DMA channel CHXPADDR register */ +#define DMA_CHMADDR_RESET_VALUE ((uint32_t)0x00000000U) /*!< the reset value of DMA channel CHXMADDR register */ +#define DMA_CHINTF_RESET_VALUE (DMA_INTF_GIF | DMA_INTF_FTFIF | \ + DMA_INTF_HTFIF | DMA_INTF_ERRIF) /*!< clear DMA channel DMA_INTF register */ + +/* DMA_INTF register */ +/* interrupt flag bits */ +#define DMA_INT_FLAG_G DMA_INTF_GIF /*!< global interrupt flag of channel */ +#define DMA_INT_FLAG_FTF DMA_INTF_FTFIF /*!< full transfer finish interrupt flag of channel */ +#define DMA_INT_FLAG_HTF DMA_INTF_HTFIF /*!< half transfer finish interrupt flag of channel */ +#define DMA_INT_FLAG_ERR DMA_INTF_ERRIF /*!< error interrupt flag of channel */ + +/* flag bits */ +#define DMA_FLAG_G DMA_INTF_GIF /*!< global interrupt flag of channel */ +#define DMA_FLAG_FTF DMA_INTF_FTFIF /*!< full transfer finish flag of channel */ +#define DMA_FLAG_HTF DMA_INTF_HTFIF /*!< half transfer finish flag of channel */ +#define DMA_FLAG_ERR DMA_INTF_ERRIF /*!< error flag of channel */ + +/* DMA_CHxCTL register */ +/* interrupt enable bits */ +#define DMA_INT_FTF DMA_CHXCTL_FTFIE /*!< enable bit for channel full transfer finish interrupt */ +#define DMA_INT_HTF DMA_CHXCTL_HTFIE /*!< enable bit for channel half transfer finish interrupt */ +#define DMA_INT_ERR DMA_CHXCTL_ERRIE /*!< enable bit for channel error interrupt */ + +/* transfer direction */ +#define DMA_PERIPHERAL_TO_MEMORY ((uint8_t)0x0000U) /*!< read from peripheral and write to memory */ +#define DMA_MEMORY_TO_PERIPHERAL ((uint8_t)0x0001U) /*!< read from memory and write to peripheral */ + +/* peripheral increasing mode */ +#define DMA_PERIPH_INCREASE_DISABLE ((uint8_t)0x0000U) /*!< next address of peripheral is fixed address mode */ +#define DMA_PERIPH_INCREASE_ENABLE ((uint8_t)0x0001U) /*!< next address of peripheral is increasing address mode */ + +/* memory increasing mode */ +#define DMA_MEMORY_INCREASE_DISABLE ((uint8_t)0x0000U) /*!< next address of memory is fixed address mode */ +#define DMA_MEMORY_INCREASE_ENABLE ((uint8_t)0x0001U) /*!< next address of memory is increasing address mode */ + +/* transfer data size of peripheral */ +#define CHCTL_PWIDTH(regval) (BITS(8,9) & ((uint32_t)(regval) << 8)) /*!< transfer data size of peripheral */ +#define DMA_PERIPHERAL_WIDTH_8BIT CHCTL_PWIDTH(0U) /*!< transfer data size of peripheral is 8-bit */ +#define DMA_PERIPHERAL_WIDTH_16BIT CHCTL_PWIDTH(1U) /*!< transfer data size of peripheral is 16-bit */ +#define DMA_PERIPHERAL_WIDTH_32BIT CHCTL_PWIDTH(2U) /*!< transfer data size of peripheral is 32-bit */ + +/* transfer data size of memory */ +#define CHCTL_MWIDTH(regval) (BITS(10,11) & ((uint32_t)(regval) << 10)) /*!< transfer data size of memory */ +#define DMA_MEMORY_WIDTH_8BIT CHCTL_MWIDTH(0U) /*!< transfer data size of memory is 8-bit */ +#define DMA_MEMORY_WIDTH_16BIT CHCTL_MWIDTH(1U) /*!< transfer data size of memory is 16-bit */ +#define DMA_MEMORY_WIDTH_32BIT CHCTL_MWIDTH(2U) /*!< transfer data size of memory is 32-bit */ + +/* channel priority level */ +#define CHCTL_PRIO(regval) (BITS(12,13) & ((uint32_t)(regval) << 12)) /*!< DMA channel priority level */ +#define DMA_PRIORITY_LOW CHCTL_PRIO(0U) /*!< low priority */ +#define DMA_PRIORITY_MEDIUM CHCTL_PRIO(1U) /*!< medium priority */ +#define DMA_PRIORITY_HIGH CHCTL_PRIO(2U) /*!< high priority */ +#define DMA_PRIORITY_ULTRA_HIGH CHCTL_PRIO(3U) /*!< ultra high priority */ + +/* memory to memory mode */ +#define DMA_MEMORY_TO_MEMORY_DISABLE ((uint32_t)0x00000000U) /*!< disable memory to memory mode */ +#define DMA_MEMORY_TO_MEMORY_ENABLE ((uint32_t)0x00000001U) /*!< enable memory to memory mode */ + +/* DMA_CHxCNT register */ +/* transfer counter */ +#define DMA_CHANNEL_CNT_MASK DMA_CHXCNT_CNT /*!< transfer counter mask */ + +/* function declarations */ +/* DMA deinitialization and initialization functions */ +/* deinitialize DMA a channel registers */ +void dma_deinit(uint32_t dma_periph, dma_channel_enum channelx); +/* initialize the parameters of DMA struct with the default values */ +void dma_struct_para_init(dma_parameter_struct* init_struct); +/* initialize DMA channel */ +void dma_init(uint32_t dma_periph, dma_channel_enum channelx, dma_parameter_struct *init_struct); +/* enable DMA circulation mode */ +void dma_circulation_enable(uint32_t dma_periph, dma_channel_enum channelx); +/* disable DMA circulation mode */ +void dma_circulation_disable(uint32_t dma_periph, dma_channel_enum channelx); +/* enable memory to memory mode */ +void dma_memory_to_memory_enable(uint32_t dma_periph, dma_channel_enum channelx); +/* disable memory to memory mode */ +void dma_memory_to_memory_disable(uint32_t dma_periph, dma_channel_enum channelx); +/* enable DMA channel */ +void dma_channel_enable(uint32_t dma_periph, dma_channel_enum channelx); +/* disable DMA channel */ +void dma_channel_disable(uint32_t dma_periph, dma_channel_enum channelx); + +/* DMA configuration functions */ +/* set DMA peripheral base address */ +void dma_periph_address_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t address); +/* set DMA memory base address */ +void dma_memory_address_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t address); +/* set the number of remaining data to be transferred by the DMA */ +void dma_transfer_number_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t number); +/* get the number of remaining data to be transferred by the DMA */ +uint32_t dma_transfer_number_get(uint32_t dma_periph, dma_channel_enum channelx); +/* configure priority level of DMA channel */ +void dma_priority_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t priority); +/* configure transfer data size of memory */ +void dma_memory_width_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t mwidth); +/* configure transfer data size of peripheral */ +void dma_periph_width_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t pwidth); +/* enable next address increasement algorithm of memory */ +void dma_memory_increase_enable(uint32_t dma_periph, dma_channel_enum channelx); +/* disable next address increasement algorithm of memory */ +void dma_memory_increase_disable(uint32_t dma_periph, dma_channel_enum channelx); +/* enable next address increasement algorithm of peripheral */ +void dma_periph_increase_enable(uint32_t dma_periph, dma_channel_enum channelx); +/* disable next address increasement algorithm of peripheral */ +void dma_periph_increase_disable(uint32_t dma_periph, dma_channel_enum channelx); +/* configure the direction of data transfer on the channel */ +void dma_transfer_direction_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t direction); + +/* flag and interrupt functions */ +/* check DMA flag is set or not */ +FlagStatus dma_flag_get(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag); +/* clear the flag of a DMA channel */ +void dma_flag_clear(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag); +/* check DMA flag and interrupt enable bit is set or not */ +FlagStatus dma_interrupt_flag_get(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag); +/* clear the interrupt flag of a DMA channel */ +void dma_interrupt_flag_clear(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag); +/* enable DMA interrupt */ +void dma_interrupt_enable(uint32_t dma_periph, dma_channel_enum channelx, uint32_t source); +/* disable DMA interrupt */ +void dma_interrupt_disable(uint32_t dma_periph, dma_channel_enum channelx, uint32_t source); + +#endif /* GD32VF103_DMA_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exmc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exmc.h new file mode 100644 index 00000000..1bacd7a8 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exmc.h @@ -0,0 +1,129 @@ +/*! + \file gd32vf103_exmc.h + \brief definitions for the EXMC + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_EXMC_H +#define GD32VF103_EXMC_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + + +/* EXMC definitions */ +#define EXMC (EXMC_BASE) /*!< EXMC register base address */ + +/* registers definitions */ +/* NOR/PSRAM */ +#define EXMC_SNCTL0 REG32(EXMC + 0x00U) /*!< EXMC SRAM/NOR flash control register 0 */ +#define EXMC_SNTCFG0 REG32(EXMC + 0x04U) /*!< EXMC SRAM/NOR flash timing configuration register 0 */ +#define EXMC_SNWTCFG0 REG32(EXMC + 0x104U) /*!< EXMC SRAM/NOR flash write timing configuration register 0 */ + +/* bits definitions */ +/* NOR/PSRAM */ +/* EXMC_SNCTLx, x=0 */ +#define EXMC_SNCTL_NRBKEN BIT(0) /*!< NOR bank enable */ +#define EXMC_SNCTL_NRMUX BIT(1) /*!< NOR bank memory address/data multiplexing */ +#define EXMC_SNCTL_NRTP BITS(2,3) /*!< NOR bank memory type */ +#define EXMC_SNCTL_NRW BITS(4,5) /*!< NOR bank memory data bus width */ +#define EXMC_SNCTL_NREN BIT(6) /*!< NOR flash access enable */ +#define EXMC_SNCTL_NRWTPOL BIT(9) /*!< NWAIT signal polarity */ +#define EXMC_SNCTL_WREN BIT(12) /*!< write enable */ +#define EXMC_SNCTL_NRWTEN BIT(13) /*!< NWAIT signal enable */ +#define EXMC_SNCTL_ASYNCWAIT BIT(15) /*!< asynchronous wait */ + +/* EXMC_SNTCFGx, x=0 */ +#define EXMC_SNTCFG_ASET BITS(0,3) /*!< address setup time */ +#define EXMC_SNTCFG_AHLD BITS(4,7) /*!< address hold time */ +#define EXMC_SNTCFG_DSET BITS(8,15) /*!< data setup time */ +#define EXMC_SNTCFG_BUSLAT BITS(16,19) /*!< bus latency */ + +/* constants definitions */ +/* EXMC NOR/SRAM timing initialize struct */ +typedef struct +{ + uint32_t bus_latency; /*!< configure the bus latency */ + uint32_t asyn_data_setuptime; /*!< configure the data setup time,asynchronous access mode valid */ + uint32_t asyn_address_holdtime; /*!< configure the address hold time,asynchronous access mode valid */ + uint32_t asyn_address_setuptime; /*!< configure the data setup time,asynchronous access mode valid */ +}exmc_norsram_timing_parameter_struct; + +/* EXMC NOR/SRAM initialize struct */ +typedef struct +{ + uint32_t norsram_region; /*!< select the region of EXMC NOR/SRAM bank */ + uint32_t asyn_wait; /*!< enable or disable the asynchronous wait function */ + uint32_t nwait_signal; /*!< enable or disable the NWAIT signal */ + uint32_t memory_write; /*!< enable or disable the write operation */ + uint32_t nwait_polarity; /*!< specifies the polarity of NWAIT signal from memory */ + uint32_t databus_width; /*!< specifies the databus width of external memory */ + uint32_t memory_type; /*!< specifies the type of external memory */ + uint32_t address_data_mux; /*!< specifies whether the data bus and address bus are multiplexed */ + exmc_norsram_timing_parameter_struct* read_write_timing; /*!< timing parameters for read and write */ +}exmc_norsram_parameter_struct; + +/* EXMC register address */ +#define EXMC_SNCTL(region) REG32(EXMC + 0x08U * (region)) /*!< EXMC SRAM/NOR flash control register */ +#define EXMC_SNTCFG(region) REG32(EXMC + 0x04U + 0x08U * (region)) /*!< EXMC SRAM/NOR flash timing configuration register */ + +/* NOR bank memory data bus width */ +#define SNCTL_NRW(regval) (BITS(4,5) & ((uint32_t)(regval) << 4)) +#define EXMC_NOR_DATABUS_WIDTH_8B SNCTL_NRW(0) /*!< NOR data width 8 bits */ +#define EXMC_NOR_DATABUS_WIDTH_16B SNCTL_NRW(1) /*!< NOR data width 16 bits */ + +/* NOR bank memory type */ +#define SNCTL_NRTP(regval) (BITS(2,3) & ((uint32_t)(regval) << 2)) +#define EXMC_MEMORY_TYPE_SRAM SNCTL_NRTP(0) /*!< SRAM,ROM */ +#define EXMC_MEMORY_TYPE_PSRAM SNCTL_NRTP(1) /*!< PSRAM,CRAM */ +#define EXMC_MEMORY_TYPE_NOR SNCTL_NRTP(2) /*!< NOR flash */ + +/* EXMC NOR/SRAM bank region definition */ +#define EXMC_BANK0_NORSRAM_REGION0 ((uint32_t)0x00000000U) /*!< bank0 NOR/SRAM region0 */ + +/* EXMC NWAIT signal polarity configuration */ +#define EXMC_NWAIT_POLARITY_LOW ((uint32_t)0x00000000U) /*!< low level is active of NWAIT */ +#define EXMC_NWAIT_POLARITY_HIGH ((uint32_t)0x00000200U) /*!< high level is active of NWAIT */ + +/* function declarations */ +/* deinitialize EXMC NOR/SRAM region */ +void exmc_norsram_deinit(uint32_t norsram_region); +/* exmc_norsram_parameter_struct parameter initialize */ +void exmc_norsram_struct_para_init(exmc_norsram_parameter_struct* exmc_norsram_init_struct); +/* initialize EXMC NOR/SRAM region */ +void exmc_norsram_init(exmc_norsram_parameter_struct* exmc_norsram_init_struct); +/* EXMC NOR/SRAM bank enable */ +void exmc_norsram_enable(uint32_t norsram_region); +/* EXMC NOR/SRAM bank disable */ +void exmc_norsram_disable(uint32_t norsram_region); + +#endif /* GD32VF103_EXMC_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exti.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exti.h new file mode 100644 index 00000000..f9f48fd3 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_exti.h @@ -0,0 +1,248 @@ +/*! + \file gd32vf103_exti.h + \brief definitions for the EXTI + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_EXTI_H +#define GD32VF103_EXTI_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + + +/* EXTI definitions */ +#define EXTI EXTI_BASE + +/* registers definitions */ +#define EXTI_INTEN REG32(EXTI + 0x00U) /*!< interrupt enable register */ +#define EXTI_EVEN REG32(EXTI + 0x04U) /*!< event enable register */ +#define EXTI_RTEN REG32(EXTI + 0x08U) /*!< rising edge trigger enable register */ +#define EXTI_FTEN REG32(EXTI + 0x0CU) /*!< falling trigger enable register */ +#define EXTI_SWIEV REG32(EXTI + 0x10U) /*!< software interrupt event register */ +#define EXTI_PD REG32(EXTI + 0x14U) /*!< pending register */ + +/* bits definitions */ +/* EXTI_INTEN */ +#define EXTI_INTEN_INTEN0 BIT(0) /*!< interrupt from line 0 */ +#define EXTI_INTEN_INTEN1 BIT(1) /*!< interrupt from line 1 */ +#define EXTI_INTEN_INTEN2 BIT(2) /*!< interrupt from line 2 */ +#define EXTI_INTEN_INTEN3 BIT(3) /*!< interrupt from line 3 */ +#define EXTI_INTEN_INTEN4 BIT(4) /*!< interrupt from line 4 */ +#define EXTI_INTEN_INTEN5 BIT(5) /*!< interrupt from line 5 */ +#define EXTI_INTEN_INTEN6 BIT(6) /*!< interrupt from line 6 */ +#define EXTI_INTEN_INTEN7 BIT(7) /*!< interrupt from line 7 */ +#define EXTI_INTEN_INTEN8 BIT(8) /*!< interrupt from line 8 */ +#define EXTI_INTEN_INTEN9 BIT(9) /*!< interrupt from line 9 */ +#define EXTI_INTEN_INTEN10 BIT(10) /*!< interrupt from line 10 */ +#define EXTI_INTEN_INTEN11 BIT(11) /*!< interrupt from line 11 */ +#define EXTI_INTEN_INTEN12 BIT(12) /*!< interrupt from line 12 */ +#define EXTI_INTEN_INTEN13 BIT(13) /*!< interrupt from line 13 */ +#define EXTI_INTEN_INTEN14 BIT(14) /*!< interrupt from line 14 */ +#define EXTI_INTEN_INTEN15 BIT(15) /*!< interrupt from line 15 */ +#define EXTI_INTEN_INTEN16 BIT(16) /*!< interrupt from line 16 */ +#define EXTI_INTEN_INTEN17 BIT(17) /*!< interrupt from line 17 */ +#define EXTI_INTEN_INTEN18 BIT(18) /*!< interrupt from line 18 */ + +/* EXTI_EVEN */ +#define EXTI_EVEN_EVEN0 BIT(0) /*!< event from line 0 */ +#define EXTI_EVEN_EVEN1 BIT(1) /*!< event from line 1 */ +#define EXTI_EVEN_EVEN2 BIT(2) /*!< event from line 2 */ +#define EXTI_EVEN_EVEN3 BIT(3) /*!< event from line 3 */ +#define EXTI_EVEN_EVEN4 BIT(4) /*!< event from line 4 */ +#define EXTI_EVEN_EVEN5 BIT(5) /*!< event from line 5 */ +#define EXTI_EVEN_EVEN6 BIT(6) /*!< event from line 6 */ +#define EXTI_EVEN_EVEN7 BIT(7) /*!< event from line 7 */ +#define EXTI_EVEN_EVEN8 BIT(8) /*!< event from line 8 */ +#define EXTI_EVEN_EVEN9 BIT(9) /*!< event from line 9 */ +#define EXTI_EVEN_EVEN10 BIT(10) /*!< event from line 10 */ +#define EXTI_EVEN_EVEN11 BIT(11) /*!< event from line 11 */ +#define EXTI_EVEN_EVEN12 BIT(12) /*!< event from line 12 */ +#define EXTI_EVEN_EVEN13 BIT(13) /*!< event from line 13 */ +#define EXTI_EVEN_EVEN14 BIT(14) /*!< event from line 14 */ +#define EXTI_EVEN_EVEN15 BIT(15) /*!< event from line 15 */ +#define EXTI_EVEN_EVEN16 BIT(16) /*!< event from line 16 */ +#define EXTI_EVEN_EVEN17 BIT(17) /*!< event from line 17 */ +#define EXTI_EVEN_EVEN18 BIT(18) /*!< event from line 18 */ + +/* EXTI_RTEN */ +#define EXTI_RTEN_RTEN0 BIT(0) /*!< rising edge from line 0 */ +#define EXTI_RTEN_RTEN1 BIT(1) /*!< rising edge from line 1 */ +#define EXTI_RTEN_RTEN2 BIT(2) /*!< rising edge from line 2 */ +#define EXTI_RTEN_RTEN3 BIT(3) /*!< rising edge from line 3 */ +#define EXTI_RTEN_RTEN4 BIT(4) /*!< rising edge from line 4 */ +#define EXTI_RTEN_RTEN5 BIT(5) /*!< rising edge from line 5 */ +#define EXTI_RTEN_RTEN6 BIT(6) /*!< rising edge from line 6 */ +#define EXTI_RTEN_RTEN7 BIT(7) /*!< rising edge from line 7 */ +#define EXTI_RTEN_RTEN8 BIT(8) /*!< rising edge from line 8 */ +#define EXTI_RTEN_RTEN9 BIT(9) /*!< rising edge from line 9 */ +#define EXTI_RTEN_RTEN10 BIT(10) /*!< rising edge from line 10 */ +#define EXTI_RTEN_RTEN11 BIT(11) /*!< rising edge from line 11 */ +#define EXTI_RTEN_RTEN12 BIT(12) /*!< rising edge from line 12 */ +#define EXTI_RTEN_RTEN13 BIT(13) /*!< rising edge from line 13 */ +#define EXTI_RTEN_RTEN14 BIT(14) /*!< rising edge from line 14 */ +#define EXTI_RTEN_RTEN15 BIT(15) /*!< rising edge from line 15 */ +#define EXTI_RTEN_RTEN16 BIT(16) /*!< rising edge from line 16 */ +#define EXTI_RTEN_RTEN17 BIT(17) /*!< rising edge from line 17 */ +#define EXTI_RTEN_RTEN18 BIT(18) /*!< rising edge from line 18 */ + +/* EXTI_FTEN */ +#define EXTI_FTEN_FTEN0 BIT(0) /*!< falling edge from line 0 */ +#define EXTI_FTEN_FTEN1 BIT(1) /*!< falling edge from line 1 */ +#define EXTI_FTEN_FTEN2 BIT(2) /*!< falling edge from line 2 */ +#define EXTI_FTEN_FTEN3 BIT(3) /*!< falling edge from line 3 */ +#define EXTI_FTEN_FTEN4 BIT(4) /*!< falling edge from line 4 */ +#define EXTI_FTEN_FTEN5 BIT(5) /*!< falling edge from line 5 */ +#define EXTI_FTEN_FTEN6 BIT(6) /*!< falling edge from line 6 */ +#define EXTI_FTEN_FTEN7 BIT(7) /*!< falling edge from line 7 */ +#define EXTI_FTEN_FTEN8 BIT(8) /*!< falling edge from line 8 */ +#define EXTI_FTEN_FTEN9 BIT(9) /*!< falling edge from line 9 */ +#define EXTI_FTEN_FTEN10 BIT(10) /*!< falling edge from line 10 */ +#define EXTI_FTEN_FTEN11 BIT(11) /*!< falling edge from line 11 */ +#define EXTI_FTEN_FTEN12 BIT(12) /*!< falling edge from line 12 */ +#define EXTI_FTEN_FTEN13 BIT(13) /*!< falling edge from line 13 */ +#define EXTI_FTEN_FTEN14 BIT(14) /*!< falling edge from line 14 */ +#define EXTI_FTEN_FTEN15 BIT(15) /*!< falling edge from line 15 */ +#define EXTI_FTEN_FTEN16 BIT(16) /*!< falling edge from line 16 */ +#define EXTI_FTEN_FTEN17 BIT(17) /*!< falling edge from line 17 */ +#define EXTI_FTEN_FTEN18 BIT(18) /*!< falling edge from line 18 */ + +/* EXTI_SWIEV */ +#define EXTI_SWIEV_SWIEV0 BIT(0) /*!< software interrupt/event request from line 0 */ +#define EXTI_SWIEV_SWIEV1 BIT(1) /*!< software interrupt/event request from line 1 */ +#define EXTI_SWIEV_SWIEV2 BIT(2) /*!< software interrupt/event request from line 2 */ +#define EXTI_SWIEV_SWIEV3 BIT(3) /*!< software interrupt/event request from line 3 */ +#define EXTI_SWIEV_SWIEV4 BIT(4) /*!< software interrupt/event request from line 4 */ +#define EXTI_SWIEV_SWIEV5 BIT(5) /*!< software interrupt/event request from line 5 */ +#define EXTI_SWIEV_SWIEV6 BIT(6) /*!< software interrupt/event request from line 6 */ +#define EXTI_SWIEV_SWIEV7 BIT(7) /*!< software interrupt/event request from line 7 */ +#define EXTI_SWIEV_SWIEV8 BIT(8) /*!< software interrupt/event request from line 8 */ +#define EXTI_SWIEV_SWIEV9 BIT(9) /*!< software interrupt/event request from line 9 */ +#define EXTI_SWIEV_SWIEV10 BIT(10) /*!< software interrupt/event request from line 10 */ +#define EXTI_SWIEV_SWIEV11 BIT(11) /*!< software interrupt/event request from line 11 */ +#define EXTI_SWIEV_SWIEV12 BIT(12) /*!< software interrupt/event request from line 12 */ +#define EXTI_SWIEV_SWIEV13 BIT(13) /*!< software interrupt/event request from line 13 */ +#define EXTI_SWIEV_SWIEV14 BIT(14) /*!< software interrupt/event request from line 14 */ +#define EXTI_SWIEV_SWIEV15 BIT(15) /*!< software interrupt/event request from line 15 */ +#define EXTI_SWIEV_SWIEV16 BIT(16) /*!< software interrupt/event request from line 16 */ +#define EXTI_SWIEV_SWIEV17 BIT(17) /*!< software interrupt/event request from line 17 */ +#define EXTI_SWIEV_SWIEV18 BIT(18) /*!< software interrupt/event request from line 18 */ + +/* EXTI_PD */ +#define EXTI_PD_PD0 BIT(0) /*!< interrupt/event pending status from line 0 */ +#define EXTI_PD_PD1 BIT(1) /*!< interrupt/event pending status from line 1 */ +#define EXTI_PD_PD2 BIT(2) /*!< interrupt/event pending status from line 2 */ +#define EXTI_PD_PD3 BIT(3) /*!< interrupt/event pending status from line 3 */ +#define EXTI_PD_PD4 BIT(4) /*!< interrupt/event pending status from line 4 */ +#define EXTI_PD_PD5 BIT(5) /*!< interrupt/event pending status from line 5 */ +#define EXTI_PD_PD6 BIT(6) /*!< interrupt/event pending status from line 6 */ +#define EXTI_PD_PD7 BIT(7) /*!< interrupt/event pending status from line 7 */ +#define EXTI_PD_PD8 BIT(8) /*!< interrupt/event pending status from line 8 */ +#define EXTI_PD_PD9 BIT(9) /*!< interrupt/event pending status from line 9 */ +#define EXTI_PD_PD10 BIT(10) /*!< interrupt/event pending status from line 10 */ +#define EXTI_PD_PD11 BIT(11) /*!< interrupt/event pending status from line 11 */ +#define EXTI_PD_PD12 BIT(12) /*!< interrupt/event pending status from line 12 */ +#define EXTI_PD_PD13 BIT(13) /*!< interrupt/event pending status from line 13 */ +#define EXTI_PD_PD14 BIT(14) /*!< interrupt/event pending status from line 14 */ +#define EXTI_PD_PD15 BIT(15) /*!< interrupt/event pending status from line 15 */ +#define EXTI_PD_PD16 BIT(16) /*!< interrupt/event pending status from line 16 */ +#define EXTI_PD_PD17 BIT(17) /*!< interrupt/event pending status from line 17 */ +#define EXTI_PD_PD18 BIT(18) /*!< interrupt/event pending status from line 18 */ + +/* constants definitions */ +/* EXTI line number */ +typedef enum { + EXTI_0 = BIT(0), /*!< EXTI line 0 */ + EXTI_1 = BIT(1), /*!< EXTI line 1 */ + EXTI_2 = BIT(2), /*!< EXTI line 2 */ + EXTI_3 = BIT(3), /*!< EXTI line 3 */ + EXTI_4 = BIT(4), /*!< EXTI line 4 */ + EXTI_5 = BIT(5), /*!< EXTI line 5 */ + EXTI_6 = BIT(6), /*!< EXTI line 6 */ + EXTI_7 = BIT(7), /*!< EXTI line 7 */ + EXTI_8 = BIT(8), /*!< EXTI line 8 */ + EXTI_9 = BIT(9), /*!< EXTI line 9 */ + EXTI_10 = BIT(10), /*!< EXTI line 10 */ + EXTI_11 = BIT(11), /*!< EXTI line 11 */ + EXTI_12 = BIT(12), /*!< EXTI line 12 */ + EXTI_13 = BIT(13), /*!< EXTI line 13 */ + EXTI_14 = BIT(14), /*!< EXTI line 14 */ + EXTI_15 = BIT(15), /*!< EXTI line 15 */ + EXTI_16 = BIT(16), /*!< EXTI line 16 */ + EXTI_17 = BIT(17), /*!< EXTI line 17 */ + EXTI_18 = BIT(18), /*!< EXTI line 18 */ +} exti_line_enum; + +/* external interrupt and event */ +typedef enum { + EXTI_INTERRUPT = 0, /*!< EXTI interrupt mode */ + EXTI_EVENT /*!< EXTI event mode */ +} exti_mode_enum; + +/* interrupt trigger mode */ +typedef enum { + EXTI_TRIG_RISING = 0, /*!< EXTI rising edge trigger */ + EXTI_TRIG_FALLING, /*!< EXTI falling edge trigger */ + EXTI_TRIG_BOTH, /*!< EXTI rising edge and falling edge trigger */ + EXTI_TRIG_NONE /*!< without rising edge or falling edge trigger */ +} exti_trig_type_enum; + +/* function declarations */ +/* initialization, EXTI lines configuration functions */ +/* deinitialize the EXTI */ +void exti_deinit(void); +/* enable the configuration of EXTI initialize */ +void exti_init(exti_line_enum linex, exti_mode_enum mode, exti_trig_type_enum trig_type); +/* enable the interrupts from EXTI line x */ +void exti_interrupt_enable(exti_line_enum linex); +/* enable the events from EXTI line x */ +void exti_event_enable(exti_line_enum linex); +/* disable the interrupts from EXTI line x */ +void exti_interrupt_disable(exti_line_enum linex); +/* disable the events from EXTI line x */ +void exti_event_disable(exti_line_enum linex); + +/* interrupt & flag functions */ +/* get EXTI lines pending flag */ +FlagStatus exti_flag_get(exti_line_enum linex); +/* clear EXTI lines pending flag */ +void exti_flag_clear(exti_line_enum linex); +/* get EXTI lines flag when the interrupt flag is set */ +FlagStatus exti_interrupt_flag_get(exti_line_enum linex); +/* clear EXTI lines pending flag */ +void exti_interrupt_flag_clear(exti_line_enum linex); +/* enable the EXTI software interrupt event */ +void exti_software_interrupt_enable(exti_line_enum linex); +/* disable the EXTI software interrupt event */ +void exti_software_interrupt_disable(exti_line_enum linex); + +#endif /* GD32VF103_EXTI_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fmc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fmc.h new file mode 100644 index 00000000..0456af56 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fmc.h @@ -0,0 +1,314 @@ +/*! + \file gd32vf103_fmc.h + \brief definitions for the FMC + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_FMC_H +#define GD32VF103_FMC_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + + +/* FMC and option byte definition */ +#define FMC FMC_BASE /*!< FMC register base address */ +#define OB OB_BASE /*!< option bytes base address */ + +/* registers definitions */ +#define FMC_WS REG32((FMC) + 0x00U) /*!< FMC wait state register */ +#define FMC_KEY0 REG32((FMC) + 0x04U) /*!< FMC unlock key register 0 */ +#define FMC_OBKEY REG32((FMC) + 0x08U) /*!< FMC option bytes unlock key register */ +#define FMC_STAT0 REG32((FMC) + 0x0CU) /*!< FMC status register 0 */ +#define FMC_CTL0 REG32((FMC) + 0x10U) /*!< FMC control register 0 */ +#define FMC_ADDR0 REG32((FMC) + 0x14U) /*!< FMC address register 0 */ +#define FMC_OBSTAT REG32((FMC) + 0x1CU) /*!< FMC option bytes status register */ +#define FMC_WP REG32((FMC) + 0x20U) /*!< FMC erase/program protection register */ +#define FMC_PID REG32((FMC) + 0x100U) /*!< FMC product ID register */ + +#define OB_SPC REG16((OB) + 0x00U) /*!< option byte security protection value */ +#define OB_USER REG16((OB) + 0x02U) /*!< option byte user value*/ +#define OB_WP0 REG16((OB) + 0x08U) /*!< option byte write protection 0 */ +#define OB_WP1 REG16((OB) + 0x0AU) /*!< option byte write protection 1 */ +#define OB_WP2 REG16((OB) + 0x0CU) /*!< option byte write protection 2 */ +#define OB_WP3 REG16((OB) + 0x0EU) /*!< option byte write protection 3 */ + +/* bits definitions */ +/* FMC_WS */ +#define FMC_WS_WSCNT BITS(0,2) /*!< wait state counter */ + +/* FMC_KEY0 */ +#define FMC_KEY0_KEY BITS(0,31) /*!< FMC_CTL0 unlock key bits */ + +/* FMC_OBKEY */ +#define FMC_OBKEY_OBKEY BITS(0,31) /*!< option bytes unlock key bits */ + +/* FMC_STAT0 */ +#define FMC_STAT0_BUSY BIT(0) /*!< flash busy flag bit */ +#define FMC_STAT0_PGERR BIT(2) /*!< flash program error flag bit */ +#define FMC_STAT0_WPERR BIT(4) /*!< erase/program protection error flag bit */ +#define FMC_STAT0_ENDF BIT(5) /*!< end of operation flag bit */ + +/* FMC_CTL0 */ +#define FMC_CTL0_PG BIT(0) /*!< main flash program for bank0 command bit */ +#define FMC_CTL0_PER BIT(1) /*!< main flash page erase for bank0 command bit */ +#define FMC_CTL0_MER BIT(2) /*!< main flash mass erase for bank0 command bit */ +#define FMC_CTL0_OBPG BIT(4) /*!< option bytes program command bit */ +#define FMC_CTL0_OBER BIT(5) /*!< option bytes erase command bit */ +#define FMC_CTL0_START BIT(6) /*!< send erase command to FMC bit */ +#define FMC_CTL0_LK BIT(7) /*!< FMC_CTL0 lock bit */ +#define FMC_CTL0_OBWEN BIT(9) /*!< option bytes erase/program enable bit */ +#define FMC_CTL0_ERRIE BIT(10) /*!< error interrupt enable bit */ +#define FMC_CTL0_ENDIE BIT(12) /*!< end of operation interrupt enable bit */ + +/* FMC_ADDR0 */ +#define FMC_ADDR0_ADDR BITS(0,31) /*!< Flash erase/program command address bits */ + +/* FMC_OBSTAT */ +#define FMC_OBSTAT_OBERR BIT(0) /*!< option bytes read error bit. */ +#define FMC_OBSTAT_SPC BIT(1) /*!< option bytes security protection code */ +#define FMC_OBSTAT_USER BITS(2,9) /*!< store USER of option bytes block after system reset */ +#define FMC_OBSTAT_DATA BITS(10,25) /*!< store DATA of option bytes block after system reset. */ + +/* FMC_WP */ +#define FMC_WP_WP BITS(0,31) /*!< store WP of option bytes block after system reset */ + +/* FMC_WSEN */ +#define FMC_WSEN_WSEN BIT(0) /*!< FMC wait state enable bit */ + +/* FMC_PID */ +#define FMC_PID_PID BITS(0,31) /*!< product ID bits */ + +/* constants definitions */ +/* define the FMC bit position and its register index offset */ +#define FMC_REGIDX_BIT(regidx, bitpos) (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos)) +#define FMC_REG_VAL(offset) (REG32(FMC + ((uint32_t)(offset) >> 6))) +#define FMC_BIT_POS(val) ((uint32_t)(val) & 0x1FU) +#define FMC_REGIDX_BITS(regidx, bitpos0, bitpos1) (((uint32_t)(regidx) << 12) | ((uint32_t)(bitpos0) << 6) | (uint32_t)(bitpos1)) +#define FMC_REG_VALS(offset) (REG32(FMC + ((uint32_t)(offset) >> 12))) +#define FMC_BIT_POS0(val) (((uint32_t)(val) >> 6) & 0x1FU) +#define FMC_BIT_POS1(val) ((uint32_t)(val) & 0x1FU) +#define FMC_REG_OFFSET_GET(flag) ((uint32_t)(flag) >> 12) + +/* configuration register */ +#define FMC_STAT0_REG_OFFSET 0x0CU /*!< status register 0 offset */ +#define FMC_CTL0_REG_OFFSET 0x10U /*!< control register 0 offset */ +#define FMC_OBSTAT_REG_OFFSET 0x1CU /*!< option byte status register offset */ + +/* fmc state */ +typedef enum +{ + FMC_READY, /*!< the operation has been completed */ + FMC_BUSY, /*!< the operation is in progress */ + FMC_PGERR, /*!< program error */ + FMC_WPERR, /*!< erase/program protection error */ + FMC_TOERR, /*!< timeout error */ +}fmc_state_enum; + +/* FMC interrupt enable */ +typedef enum +{ + FMC_INT_END = FMC_REGIDX_BIT(FMC_CTL0_REG_OFFSET, 12U), /*!< enable FMC end of program interrupt */ + FMC_INT_ERR = FMC_REGIDX_BIT(FMC_CTL0_REG_OFFSET, 10U), /*!< enable FMC error interrupt */ +}fmc_int_enum; + +/* FMC flags */ +typedef enum +{ + FMC_FLAG_BUSY = FMC_REGIDX_BIT(FMC_STAT0_REG_OFFSET, 0U), /*!< FMC busy flag */ + FMC_FLAG_PGERR = FMC_REGIDX_BIT(FMC_STAT0_REG_OFFSET, 2U), /*!< FMC operation error flag bit */ + FMC_FLAG_WPERR = FMC_REGIDX_BIT(FMC_STAT0_REG_OFFSET, 4U), /*!< FMC erase/program protection error flag bit */ + FMC_FLAG_END = FMC_REGIDX_BIT(FMC_STAT0_REG_OFFSET, 5U), /*!< FMC end of operation flag bit */ + FMC_FLAG_OBERR = FMC_REGIDX_BIT(FMC_OBSTAT_REG_OFFSET, 0U), /*!< FMC option bytes read error flag */ +}fmc_flag_enum; + +/* FMC interrupt flags */ +typedef enum +{ + FMC_INT_FLAG_PGERR = FMC_REGIDX_BITS(FMC_STAT0_REG_OFFSET, 2U, 10U), /*!< FMC operation error interrupt flag bit */ + FMC_INT_FLAG_WPERR = FMC_REGIDX_BITS(FMC_STAT0_REG_OFFSET, 4U, 10U), /*!< FMC erase/program protection error interrupt flag bit */ + FMC_INT_FLAG_END = FMC_REGIDX_BITS(FMC_STAT0_REG_OFFSET, 5U, 12U), /*!< FMC end of operation interrupt flag bit */ +}fmc_interrupt_flag_enum; + +/* unlock key */ +#define UNLOCK_KEY0 ((uint32_t)0x45670123U) /*!< unlock key 0 */ +#define UNLOCK_KEY1 ((uint32_t)0xCDEF89ABU) /*!< unlock key 1 */ + +/* FMC wait state counter */ +#define WS_WSCNT(regval) (BITS(0,2) & ((uint32_t)(regval))) +#define WS_WSCNT_0 WS_WSCNT(0) /*!< FMC 0 wait */ +#define WS_WSCNT_1 WS_WSCNT(1) /*!< FMC 1 wait */ +#define WS_WSCNT_2 WS_WSCNT(2) /*!< FMC 2 wait */ + +/* option bytes software/hardware free watch dog timer */ +#define OB_FWDGT_SW ((uint8_t)0x01U) /*!< software free watchdog */ +#define OB_FWDGT_HW ((uint8_t)0x00U) /*!< hardware free watchdog */ + +/* option bytes reset or not entering deep sleep mode */ +#define OB_DEEPSLEEP_NRST ((uint8_t)0x02U) /*!< no reset when entering deepsleep mode */ +#define OB_DEEPSLEEP_RST ((uint8_t)0x00U) /*!< generate a reset instead of entering deepsleep mode */ + +/* option bytes reset or not entering standby mode */ +#define OB_STDBY_NRST ((uint8_t)0x04U) /*!< no reset when entering deepsleep mode */ +#define OB_STDBY_RST ((uint8_t)0x00U) /*!< generate a reset instead of entering standby mode */ + +/* option bytes boot bank value */ +#define OB_BOOT_B0 ((uint8_t)0x08U) /*!< boot from bank0 */ + +#define OB_USER_MASK ((uint8_t)0xF0U) /*!< MASK value */ + +/* read protect configure */ +#define FMC_NSPC ((uint8_t)0xA5U) /*!< no security protection */ +#define FMC_USPC ((uint8_t)0xBBU) /*!< under security protection */ + +/* OB_SPC */ +#define OB_SPC_SPC ((uint32_t)0x000000FFU) /*!< option byte security protection value */ +#define OB_SPC_SPC_N ((uint32_t)0x0000FF00U) /*!< option byte security protection complement value */ + +/* OB_USER */ +#define OB_USER_USER ((uint32_t)0x00FF0000U) /*!< user option value */ +#define OB_USER_USER_N ((uint32_t)0xFF000000U) /*!< user option complement value */ + +/* OB_WP0 */ +#define OB_WP0_WP0 ((uint32_t)0x000000FFU) /*!< FMC write protection option value */ + +/* OB_WP1 */ +#define OB_WP1_WP1 ((uint32_t)0x0000FF00U) /*!< FMC write protection option complement value */ + +/* OB_WP2 */ +#define OB_WP2_WP2 ((uint32_t)0x00FF0000U) /*!< FMC write protection option value */ + +/* OB_WP3 */ +#define OB_WP3_WP3 ((uint32_t)0xFF000000U) /*!< FMC write protection option complement value */ + +/* option bytes write protection */ +#define OB_WP_0 ((uint32_t)0x00000001U) /*!< erase/program protection of sector 0 */ +#define OB_WP_1 ((uint32_t)0x00000002U) /*!< erase/program protection of sector 1 */ +#define OB_WP_2 ((uint32_t)0x00000004U) /*!< erase/program protection of sector 2 */ +#define OB_WP_3 ((uint32_t)0x00000008U) /*!< erase/program protection of sector 3 */ +#define OB_WP_4 ((uint32_t)0x00000010U) /*!< erase/program protection of sector 4 */ +#define OB_WP_5 ((uint32_t)0x00000020U) /*!< erase/program protection of sector 5 */ +#define OB_WP_6 ((uint32_t)0x00000040U) /*!< erase/program protection of sector 6 */ +#define OB_WP_7 ((uint32_t)0x00000080U) /*!< erase/program protection of sector 7 */ +#define OB_WP_8 ((uint32_t)0x00000100U) /*!< erase/program protection of sector 8 */ +#define OB_WP_9 ((uint32_t)0x00000200U) /*!< erase/program protection of sector 9 */ +#define OB_WP_10 ((uint32_t)0x00000400U) /*!< erase/program protection of sector 10 */ +#define OB_WP_11 ((uint32_t)0x00000800U) /*!< erase/program protection of sector 11 */ +#define OB_WP_12 ((uint32_t)0x00001000U) /*!< erase/program protection of sector 12 */ +#define OB_WP_13 ((uint32_t)0x00002000U) /*!< erase/program protection of sector 13 */ +#define OB_WP_14 ((uint32_t)0x00004000U) /*!< erase/program protection of sector 14 */ +#define OB_WP_15 ((uint32_t)0x00008000U) /*!< erase/program protection of sector 15 */ +#define OB_WP_16 ((uint32_t)0x00010000U) /*!< erase/program protection of sector 16 */ +#define OB_WP_17 ((uint32_t)0x00020000U) /*!< erase/program protection of sector 17 */ +#define OB_WP_18 ((uint32_t)0x00040000U) /*!< erase/program protection of sector 18 */ +#define OB_WP_19 ((uint32_t)0x00080000U) /*!< erase/program protection of sector 19 */ +#define OB_WP_20 ((uint32_t)0x00100000U) /*!< erase/program protection of sector 20 */ +#define OB_WP_21 ((uint32_t)0x00200000U) /*!< erase/program protection of sector 21 */ +#define OB_WP_22 ((uint32_t)0x00400000U) /*!< erase/program protection of sector 22 */ +#define OB_WP_23 ((uint32_t)0x00800000U) /*!< erase/program protection of sector 23 */ +#define OB_WP_24 ((uint32_t)0x01000000U) /*!< erase/program protection of sector 24 */ +#define OB_WP_25 ((uint32_t)0x02000000U) /*!< erase/program protection of sector 25 */ +#define OB_WP_26 ((uint32_t)0x04000000U) /*!< erase/program protection of sector 26 */ +#define OB_WP_27 ((uint32_t)0x08000000U) /*!< erase/program protection of sector 27 */ +#define OB_WP_28 ((uint32_t)0x10000000U) /*!< erase/program protection of sector 28 */ +#define OB_WP_29 ((uint32_t)0x20000000U) /*!< erase/program protection of sector 29 */ +#define OB_WP_30 ((uint32_t)0x40000000U) /*!< erase/program protection of sector 30 */ +#define OB_WP_31 ((uint32_t)0x80000000U) /*!< erase/program protection of sector 31 */ +#define OB_WP_ALL ((uint32_t)0xFFFFFFFFU) /*!< erase/program protection of all sectors */ + +/* FMC timeout */ +#define FMC_TIMEOUT_COUNT ((uint32_t)0x000F0000U) /*!< FMC timeout count value */ + +/* FMC BANK address */ +#define FMC_SIZE (*(uint16_t *)0x1FFFF7E0U) /*!< FMC size */ +#define SRAM_SIZE (*(uint16_t *)0x1FFFF7E2U) /*!< SRAM size*/ + +/* function declarations */ +/* FMC main memory programming functions */ +/* set the FMC wait state counter */ +void fmc_wscnt_set(uint32_t wscnt); +/* unlock the main FMC operation */ +void fmc_unlock(void); +/* lock the main FMC operation */ +void fmc_lock(void); +/* FMC erase page */ +fmc_state_enum fmc_page_erase(uint32_t page_address); +/* FMC erase whole chip */ +fmc_state_enum fmc_mass_erase(void); +/* FMC program a word at the corresponding address */ +fmc_state_enum fmc_word_program(uint32_t address, uint32_t data); +/* FMC program a half word at the corresponding address */ +fmc_state_enum fmc_halfword_program(uint32_t address, uint16_t data); + +/* FMC option bytes programming functions */ +/* unlock the option byte operation */ +void ob_unlock(void); +/* lock the option byte operation */ +void ob_lock(void); +/* erase the FMC option byte */ +fmc_state_enum ob_erase(void); +/* enable write protect */ +fmc_state_enum ob_write_protection_enable(uint32_t ob_wp); +/* configure the option byte security protection */ +fmc_state_enum ob_security_protection_config(uint8_t ob_spc); +/* write the FMC option byte */ +fmc_state_enum ob_user_write(uint8_t ob_fwdgt, uint8_t ob_deepsleep, uint8_t ob_stdby, uint8_t ob_boot); +/* program option bytes data */ +fmc_state_enum ob_data_program(uint32_t address, uint8_t data); +/* get the FMC option byte user */ +uint8_t ob_user_get(void); +/* get OB_DATA in register FMC_OBSTAT */ +uint16_t ob_data_get(void); +/* get the FMC option byte write protection */ +uint32_t ob_write_protection_get(void); +/* get FMC option byte security protection code value */ +FlagStatus ob_spc_get(void); + +/* FMC interrupts and flags management functions */ +/* enable FMC interrupt */ +void fmc_interrupt_enable(uint32_t interrupt); +/* disable FMC interrupt */ +void fmc_interrupt_disable(uint32_t interrupt); +/* check flag is set or not */ +FlagStatus fmc_flag_get(uint32_t flag); +/* clear the FMC flag */ +void fmc_flag_clear(uint32_t flag); +/* get FMC interrupt flag state */ +FlagStatus fmc_interrupt_flag_get(fmc_interrupt_flag_enum flag); +/* clear FMC interrupt flag state */ +void fmc_interrupt_flag_clear(fmc_interrupt_flag_enum flag); +/* return the FMC state */ +fmc_state_enum fmc_state_get(void); +/* check FMC ready or not */ +fmc_state_enum fmc_ready_wait(uint32_t timeout); + +#endif /* GD32VF103_FMC_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fwdgt.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fwdgt.h new file mode 100644 index 00000000..0517e20c --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_fwdgt.h @@ -0,0 +1,107 @@ +/*! + \file gd32vf103_fwdgt.h + \brief definitions for the FWDGT + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_FWDGT_H +#define GD32VF103_FWDGT_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + + +/* FWDGT definitions */ +#define FWDGT FWDGT_BASE /*!< FWDGT base address */ + +/* registers definitions */ +#define FWDGT_CTL REG32((FWDGT) + 0x00000000U) /*!< FWDGT control register */ +#define FWDGT_PSC REG32((FWDGT) + 0x00000004U) /*!< FWDGT prescaler register */ +#define FWDGT_RLD REG32((FWDGT) + 0x00000008U) /*!< FWDGT reload register */ +#define FWDGT_STAT REG32((FWDGT) + 0x0000000CU) /*!< FWDGT status register */ + +/* bits definitions */ +/* FWDGT_CTL */ +#define FWDGT_CTL_CMD BITS(0,15) /*!< FWDGT command value */ + +/* FWDGT_PSC */ +#define FWDGT_PSC_PSC BITS(0,2) /*!< FWDGT prescaler divider value */ + +/* FWDGT_RLD */ +#define FWDGT_RLD_RLD BITS(0,11) /*!< FWDGT counter reload value */ + +/* FWDGT_STAT */ +#define FWDGT_STAT_PUD BIT(0) /*!< FWDGT prescaler divider value update */ +#define FWDGT_STAT_RUD BIT(1) /*!< FWDGT counter reload value update */ + +/* constants definitions */ +/* psc register value */ +#define PSC_PSC(regval) (BITS(0,2) & ((uint32_t)(regval) << 0)) +#define FWDGT_PSC_DIV4 ((uint8_t)PSC_PSC(0)) /*!< FWDGT prescaler set to 4 */ +#define FWDGT_PSC_DIV8 ((uint8_t)PSC_PSC(1)) /*!< FWDGT prescaler set to 8 */ +#define FWDGT_PSC_DIV16 ((uint8_t)PSC_PSC(2)) /*!< FWDGT prescaler set to 16 */ +#define FWDGT_PSC_DIV32 ((uint8_t)PSC_PSC(3)) /*!< FWDGT prescaler set to 32 */ +#define FWDGT_PSC_DIV64 ((uint8_t)PSC_PSC(4)) /*!< FWDGT prescaler set to 64 */ +#define FWDGT_PSC_DIV128 ((uint8_t)PSC_PSC(5)) /*!< FWDGT prescaler set to 128 */ +#define FWDGT_PSC_DIV256 ((uint8_t)PSC_PSC(6)) /*!< FWDGT prescaler set to 256 */ + +/* control value */ +#define FWDGT_WRITEACCESS_ENABLE ((uint16_t)0x5555U) /*!< FWDGT_CTL bits write access enable value */ +#define FWDGT_WRITEACCESS_DISABLE ((uint16_t)0x0000U) /*!< FWDGT_CTL bits write access disable value */ +#define FWDGT_KEY_RELOAD ((uint16_t)0xAAAAU) /*!< FWDGT_CTL bits fwdgt counter reload value */ +#define FWDGT_KEY_ENABLE ((uint16_t)0xCCCCU) /*!< FWDGT_CTL bits fwdgt counter enable value */ + +/* FWDGT timeout value */ +#define FWDGT_PSC_TIMEOUT ((uint32_t)0x000FFFFFU) /*!< FWDGT_PSC register write operation state flag timeout */ +#define FWDGT_RLD_TIMEOUT ((uint32_t)0x000FFFFFU) /*!< FWDGT_RLD register write operation state flag timeout */ + +/* FWDGT flag definitions */ +#define FWDGT_FLAG_PUD FWDGT_STAT_PUD /*!< FWDGT prescaler divider value update flag */ +#define FWDGT_FLAG_RUD FWDGT_STAT_RUD /*!< FWDGT counter reload value update flag */ + +/* function declarations */ +/* enable write access to FWDGT_PSC and FWDGT_RLD */ +void fwdgt_write_enable(void); +/* disable write access to FWDGT_PSC and FWDGT_RLD */ +void fwdgt_write_disable(void); +/* start the free watchdog timer counter */ +void fwdgt_enable(void); + +/* reload the counter of FWDGT */ +void fwdgt_counter_reload(void); +/* configure counter reload value, and prescaler divider value */ +ErrStatus fwdgt_config(uint16_t reload_value, uint8_t prescaler_div); + +/* get flag state of FWDGT */ +FlagStatus fwdgt_flag_get(uint16_t flag); + +#endif /* GD32VF103_FWDGT_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_gpio.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_gpio.h new file mode 100644 index 00000000..9bc9c3e2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_gpio.h @@ -0,0 +1,423 @@ +/*! + \file gd32vf103_gpio.h + \brief definitions for the GPIO + + \version 2019-06-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_GPIO_H +#define GD32VF103_GPIO_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* GPIOx(x=A,B,C,D,E) definitions */ +#define GPIOA (GPIO_BASE + 0x00000000U) +#define GPIOB (GPIO_BASE + 0x00000400U) +#define GPIOC (GPIO_BASE + 0x00000800U) +#define GPIOD (GPIO_BASE + 0x00000C00U) +#define GPIOE (GPIO_BASE + 0x00001000U) + +/* AFIO definitions */ +#define AFIO AFIO_BASE + +/* registers definitions */ + +/* GPIO registers definitions */ +#define GPIO_CTL0(gpiox) REG32((gpiox) + 0x00U) /*!< GPIO port control register 0 */ +#define GPIO_CTL1(gpiox) REG32((gpiox) + 0x04U) /*!< GPIO port control register 1 */ +#define GPIO_ISTAT(gpiox) REG32((gpiox) + 0x08U) /*!< GPIO port input status register */ +#define GPIO_OCTL(gpiox) REG32((gpiox) + 0x0CU) /*!< GPIO port output control register */ +#define GPIO_BOP(gpiox) REG32((gpiox) + 0x10U) /*!< GPIO port bit operation register */ +#define GPIO_BC(gpiox) REG32((gpiox) + 0x14U) /*!< GPIO bit clear register */ +#define GPIO_LOCK(gpiox) REG32((gpiox) + 0x18U) /*!< GPIO port configuration lock register */ + +/* AFIO registers definitions */ +#define AFIO_EC REG32(AFIO + 0x00U) /*!< AFIO event control register */ +#define AFIO_PCF0 REG32(AFIO + 0x04U) /*!< AFIO port configuration register 0 */ +#define AFIO_EXTISS0 REG32(AFIO + 0x08U) /*!< AFIO port EXTI sources selection register 0 */ +#define AFIO_EXTISS1 REG32(AFIO + 0x0CU) /*!< AFIO port EXTI sources selection register 1 */ +#define AFIO_EXTISS2 REG32(AFIO + 0x10U) /*!< AFIO port EXTI sources selection register 2 */ +#define AFIO_EXTISS3 REG32(AFIO + 0x14U) /*!< AFIO port EXTI sources selection register 3 */ +#define AFIO_PCF1 REG32(AFIO + 0x1CU) /*!< AFIO port configuration register 1 */ + +/* bits definitions */ +/* GPIO_CTL0 */ +#define GPIO_CTL0_MD0 BITS(0, 1) /*!< port 0 mode bits */ +#define GPIO_CTL0_CTL0 BITS(2, 3) /*!< pin 0 configuration bits */ +#define GPIO_CTL0_MD1 BITS(4, 5) /*!< port 1 mode bits */ +#define GPIO_CTL0_CTL1 BITS(6, 7) /*!< pin 1 configuration bits */ +#define GPIO_CTL0_MD2 BITS(8, 9) /*!< port 2 mode bits */ +#define GPIO_CTL0_CTL2 BITS(10, 11) /*!< pin 2 configuration bits */ +#define GPIO_CTL0_MD3 BITS(12, 13) /*!< port 3 mode bits */ +#define GPIO_CTL0_CTL3 BITS(14, 15) /*!< pin 3 configuration bits */ +#define GPIO_CTL0_MD4 BITS(16, 17) /*!< port 4 mode bits */ +#define GPIO_CTL0_CTL4 BITS(18, 19) /*!< pin 4 configuration bits */ +#define GPIO_CTL0_MD5 BITS(20, 21) /*!< port 5 mode bits */ +#define GPIO_CTL0_CTL5 BITS(22, 23) /*!< pin 5 configuration bits */ +#define GPIO_CTL0_MD6 BITS(24, 25) /*!< port 6 mode bits */ +#define GPIO_CTL0_CTL6 BITS(26, 27) /*!< pin 6 configuration bits */ +#define GPIO_CTL0_MD7 BITS(28, 29) /*!< port 7 mode bits */ +#define GPIO_CTL0_CTL7 BITS(30, 31) /*!< pin 7 configuration bits */ + +/* GPIO_CTL1 */ +#define GPIO_CTL1_MD8 BITS(0, 1) /*!< port 8 mode bits */ +#define GPIO_CTL1_CTL8 BITS(2, 3) /*!< pin 8 configuration bits */ +#define GPIO_CTL1_MD9 BITS(4, 5) /*!< port 9 mode bits */ +#define GPIO_CTL1_CTL9 BITS(6, 7) /*!< pin 9 configuration bits */ +#define GPIO_CTL1_MD10 BITS(8, 9) /*!< port 10 mode bits */ +#define GPIO_CTL1_CTL10 BITS(10, 11) /*!< pin 10 configuration bits */ +#define GPIO_CTL1_MD11 BITS(12, 13) /*!< port 11 mode bits */ +#define GPIO_CTL1_CTL11 BITS(14, 15) /*!< pin 11 configuration bits */ +#define GPIO_CTL1_MD12 BITS(16, 17) /*!< port 12 mode bits */ +#define GPIO_CTL1_CTL12 BITS(18, 19) /*!< pin 12 configuration bits */ +#define GPIO_CTL1_MD13 BITS(20, 21) /*!< port 13 mode bits */ +#define GPIO_CTL1_CTL13 BITS(22, 23) /*!< pin 13 configuration bits */ +#define GPIO_CTL1_MD14 BITS(24, 25) /*!< port 14 mode bits */ +#define GPIO_CTL1_CTL14 BITS(26, 27) /*!< pin 14 configuration bits */ +#define GPIO_CTL1_MD15 BITS(28, 29) /*!< port 15 mode bits */ +#define GPIO_CTL1_CTL15 BITS(30, 31) /*!< pin 15 configuration bits */ + +/* GPIO_ISTAT */ +#define GPIO_ISTAT_ISTAT0 BIT(0) /*!< pin 0 input status */ +#define GPIO_ISTAT_ISTAT1 BIT(1) /*!< pin 1 input status */ +#define GPIO_ISTAT_ISTAT2 BIT(2) /*!< pin 2 input status */ +#define GPIO_ISTAT_ISTAT3 BIT(3) /*!< pin 3 input status */ +#define GPIO_ISTAT_ISTAT4 BIT(4) /*!< pin 4 input status */ +#define GPIO_ISTAT_ISTAT5 BIT(5) /*!< pin 5 input status */ +#define GPIO_ISTAT_ISTAT6 BIT(6) /*!< pin 6 input status */ +#define GPIO_ISTAT_ISTAT7 BIT(7) /*!< pin 7 input status */ +#define GPIO_ISTAT_ISTAT8 BIT(8) /*!< pin 8 input status */ +#define GPIO_ISTAT_ISTAT9 BIT(9) /*!< pin 9 input status */ +#define GPIO_ISTAT_ISTAT10 BIT(10) /*!< pin 10 input status */ +#define GPIO_ISTAT_ISTAT11 BIT(11) /*!< pin 11 input status */ +#define GPIO_ISTAT_ISTAT12 BIT(12) /*!< pin 12 input status */ +#define GPIO_ISTAT_ISTAT13 BIT(13) /*!< pin 13 input status */ +#define GPIO_ISTAT_ISTAT14 BIT(14) /*!< pin 14 input status */ +#define GPIO_ISTAT_ISTAT15 BIT(15) /*!< pin 15 input status */ + +/* GPIO_OCTL */ +#define GPIO_OCTL_OCTL0 BIT(0) /*!< pin 0 output bit */ +#define GPIO_OCTL_OCTL1 BIT(1) /*!< pin 1 output bit */ +#define GPIO_OCTL_OCTL2 BIT(2) /*!< pin 2 output bit */ +#define GPIO_OCTL_OCTL3 BIT(3) /*!< pin 3 output bit */ +#define GPIO_OCTL_OCTL4 BIT(4) /*!< pin 4 output bit */ +#define GPIO_OCTL_OCTL5 BIT(5) /*!< pin 5 output bit */ +#define GPIO_OCTL_OCTL6 BIT(6) /*!< pin 6 output bit */ +#define GPIO_OCTL_OCTL7 BIT(7) /*!< pin 7 output bit */ +#define GPIO_OCTL_OCTL8 BIT(8) /*!< pin 8 output bit */ +#define GPIO_OCTL_OCTL9 BIT(9) /*!< pin 9 output bit */ +#define GPIO_OCTL_OCTL10 BIT(10) /*!< pin 10 output bit */ +#define GPIO_OCTL_OCTL11 BIT(11) /*!< pin 11 output bit */ +#define GPIO_OCTL_OCTL12 BIT(12) /*!< pin 12 output bit */ +#define GPIO_OCTL_OCTL13 BIT(13) /*!< pin 13 output bit */ +#define GPIO_OCTL_OCTL14 BIT(14) /*!< pin 14 output bit */ +#define GPIO_OCTL_OCTL15 BIT(15) /*!< pin 15 output bit */ + +/* GPIO_BOP */ +#define GPIO_BOP_BOP0 BIT(0) /*!< pin 0 set bit */ +#define GPIO_BOP_BOP1 BIT(1) /*!< pin 1 set bit */ +#define GPIO_BOP_BOP2 BIT(2) /*!< pin 2 set bit */ +#define GPIO_BOP_BOP3 BIT(3) /*!< pin 3 set bit */ +#define GPIO_BOP_BOP4 BIT(4) /*!< pin 4 set bit */ +#define GPIO_BOP_BOP5 BIT(5) /*!< pin 5 set bit */ +#define GPIO_BOP_BOP6 BIT(6) /*!< pin 6 set bit */ +#define GPIO_BOP_BOP7 BIT(7) /*!< pin 7 set bit */ +#define GPIO_BOP_BOP8 BIT(8) /*!< pin 8 set bit */ +#define GPIO_BOP_BOP9 BIT(9) /*!< pin 9 set bit */ +#define GPIO_BOP_BOP10 BIT(10) /*!< pin 10 set bit */ +#define GPIO_BOP_BOP11 BIT(11) /*!< pin 11 set bit */ +#define GPIO_BOP_BOP12 BIT(12) /*!< pin 12 set bit */ +#define GPIO_BOP_BOP13 BIT(13) /*!< pin 13 set bit */ +#define GPIO_BOP_BOP14 BIT(14) /*!< pin 14 set bit */ +#define GPIO_BOP_BOP15 BIT(15) /*!< pin 15 set bit */ +#define GPIO_BOP_CR0 BIT(16) /*!< pin 0 clear bit */ +#define GPIO_BOP_CR1 BIT(17) /*!< pin 1 clear bit */ +#define GPIO_BOP_CR2 BIT(18) /*!< pin 2 clear bit */ +#define GPIO_BOP_CR3 BIT(19) /*!< pin 3 clear bit */ +#define GPIO_BOP_CR4 BIT(20) /*!< pin 4 clear bit */ +#define GPIO_BOP_CR5 BIT(21) /*!< pin 5 clear bit */ +#define GPIO_BOP_CR6 BIT(22) /*!< pin 6 clear bit */ +#define GPIO_BOP_CR7 BIT(23) /*!< pin 7 clear bit */ +#define GPIO_BOP_CR8 BIT(24) /*!< pin 8 clear bit */ +#define GPIO_BOP_CR9 BIT(25) /*!< pin 9 clear bit */ +#define GPIO_BOP_CR10 BIT(26) /*!< pin 10 clear bit */ +#define GPIO_BOP_CR11 BIT(27) /*!< pin 11 clear bit */ +#define GPIO_BOP_CR12 BIT(28) /*!< pin 12 clear bit */ +#define GPIO_BOP_CR13 BIT(29) /*!< pin 13 clear bit */ +#define GPIO_BOP_CR14 BIT(30) /*!< pin 14 clear bit */ +#define GPIO_BOP_CR15 BIT(31) /*!< pin 15 clear bit */ + +/* GPIO_BC */ +#define GPIO_BC_CR0 BIT(0) /*!< pin 0 clear bit */ +#define GPIO_BC_CR1 BIT(1) /*!< pin 1 clear bit */ +#define GPIO_BC_CR2 BIT(2) /*!< pin 2 clear bit */ +#define GPIO_BC_CR3 BIT(3) /*!< pin 3 clear bit */ +#define GPIO_BC_CR4 BIT(4) /*!< pin 4 clear bit */ +#define GPIO_BC_CR5 BIT(5) /*!< pin 5 clear bit */ +#define GPIO_BC_CR6 BIT(6) /*!< pin 6 clear bit */ +#define GPIO_BC_CR7 BIT(7) /*!< pin 7 clear bit */ +#define GPIO_BC_CR8 BIT(8) /*!< pin 8 clear bit */ +#define GPIO_BC_CR9 BIT(9) /*!< pin 9 clear bit */ +#define GPIO_BC_CR10 BIT(10) /*!< pin 10 clear bit */ +#define GPIO_BC_CR11 BIT(11) /*!< pin 11 clear bit */ +#define GPIO_BC_CR12 BIT(12) /*!< pin 12 clear bit */ +#define GPIO_BC_CR13 BIT(13) /*!< pin 13 clear bit */ +#define GPIO_BC_CR14 BIT(14) /*!< pin 14 clear bit */ +#define GPIO_BC_CR15 BIT(15) /*!< pin 15 clear bit */ + +/* GPIO_LOCK */ +#define GPIO_LOCK_LK0 BIT(0) /*!< pin 0 lock bit */ +#define GPIO_LOCK_LK1 BIT(1) /*!< pin 1 lock bit */ +#define GPIO_LOCK_LK2 BIT(2) /*!< pin 2 lock bit */ +#define GPIO_LOCK_LK3 BIT(3) /*!< pin 3 lock bit */ +#define GPIO_LOCK_LK4 BIT(4) /*!< pin 4 lock bit */ +#define GPIO_LOCK_LK5 BIT(5) /*!< pin 5 lock bit */ +#define GPIO_LOCK_LK6 BIT(6) /*!< pin 6 lock bit */ +#define GPIO_LOCK_LK7 BIT(7) /*!< pin 7 lock bit */ +#define GPIO_LOCK_LK8 BIT(8) /*!< pin 8 lock bit */ +#define GPIO_LOCK_LK9 BIT(9) /*!< pin 9 lock bit */ +#define GPIO_LOCK_LK10 BIT(10) /*!< pin 10 lock bit */ +#define GPIO_LOCK_LK11 BIT(11) /*!< pin 11 lock bit */ +#define GPIO_LOCK_LK12 BIT(12) /*!< pin 12 lock bit */ +#define GPIO_LOCK_LK13 BIT(13) /*!< pin 13 lock bit */ +#define GPIO_LOCK_LK14 BIT(14) /*!< pin 14 lock bit */ +#define GPIO_LOCK_LK15 BIT(15) /*!< pin 15 lock bit */ +#define GPIO_LOCK_LKK BIT(16) /*!< pin sequence lock key */ + +/* AFIO_EC */ +#define AFIO_EC_PIN BITS(0, 3) /*!< event output pin selection */ +#define AFIO_EC_PORT BITS(4, 6) /*!< event output port selection */ +#define AFIO_EC_EOE BIT(7) /*!< event output enable */ + +/* AFIO_PCF0 */ +#define AFIO_PCF0_SPI0_REMAP BIT(0) /*!< SPI0 remapping */ +#define AFIO_PCF0_I2C0_REMAP BIT(1) /*!< I2C0 remapping */ +#define AFIO_PCF0_USART0_REMAP BIT(2) /*!< USART0 remapping */ +#define AFIO_PCF0_USART1_REMAP BIT(3) /*!< USART1 remapping */ +#define AFIO_PCF0_USART2_REMAP BITS(4, 5) /*!< USART2 remapping */ +#define AFIO_PCF0_TIMER0_REMAP BITS(6, 7) /*!< TIMER0 remapping */ +#define AFIO_PCF0_TIMER1_REMAP BITS(8, 9) /*!< TIMER1 remapping */ +#define AFIO_PCF0_TIMER2_REMAP BITS(10, 11) /*!< TIMER2 remapping */ +#define AFIO_PCF0_TIMER3_REMAP BIT(12) /*!< TIMER3 remapping */ +#define AFIO_PCF0_CAN_REMAP BITS(13, 14) /*!< CAN remapping */ +#define AFIO_PCF0_PD01_REMAP BIT(15) /*!< port D0/port D1 mapping on OSC_IN/OSC_OUT */ +#define AFIO_PCF0_TIMER4CH3_IREMAP BIT(16) /*!< TIMER3 channel3 internal remapping */ +#define AFIO_PCF0_SWJ_CFG BITS(24, 26) /*!< serial wire JTAG configuration */ +#define AFIO_PCF0_SPI2_REMAP BIT(28) /*!< SPI2/I2S2 remapping */ +#define AFIO_PCF0_TIMER1_ITI1_REMAP BIT(29) /*!< TIMER1 internal trigger 1 remapping */ + +/* AFIO_EXTISS0 */ +#define AFIO_EXTI0_SS BITS(0, 3) /*!< EXTI 0 sources selection */ +#define AFIO_EXTI1_SS BITS(4, 7) /*!< EXTI 1 sources selection */ +#define AFIO_EXTI2_SS BITS(8, 11) /*!< EXTI 2 sources selection */ +#define AFIO_EXTI3_SS BITS(12, 15) /*!< EXTI 3 sources selection */ + +/* AFIO_EXTISS1 */ +#define AFIO_EXTI4_SS BITS(0, 3) /*!< EXTI 4 sources selection */ +#define AFIO_EXTI5_SS BITS(4, 7) /*!< EXTI 5 sources selection */ +#define AFIO_EXTI6_SS BITS(8, 11) /*!< EXTI 6 sources selection */ +#define AFIO_EXTI7_SS BITS(12, 15) /*!< EXTI 7 sources selection */ + +/* AFIO_EXTISS2 */ +#define AFIO_EXTI8_SS BITS(0, 3) /*!< EXTI 8 sources selection */ +#define AFIO_EXTI9_SS BITS(4, 7) /*!< EXTI 9 sources selection */ +#define AFIO_EXTI10_SS BITS(8, 11) /*!< EXTI 10 sources selection */ +#define AFIO_EXTI11_SS BITS(12, 15) /*!< EXTI 11 sources selection */ + +/* AFIO_EXTISS3 */ +#define AFIO_EXTI12_SS BITS(0, 3) /*!< EXTI 12 sources selection */ +#define AFIO_EXTI13_SS BITS(4, 7) /*!< EXTI 13 sources selection */ +#define AFIO_EXTI14_SS BITS(8, 11) /*!< EXTI 14 sources selection */ +#define AFIO_EXTI15_SS BITS(12, 15) /*!< EXTI 15 sources selection */ + +/* AFIO_PCF1 */ +#define AFIO_PCF1_EXMC_NADV BIT(10) /*!< EXMC_NADV connect/disconnect */ + +/* constants definitions */ +typedef FlagStatus bit_status; + +/* GPIO mode values set */ +#define GPIO_MODE_SET(n, mode) ((uint32_t)((uint32_t)(mode) << (4U * (n)))) +#define GPIO_MODE_MASK(n) (0xFU << (4U * (n))) + +/* GPIO mode definitions */ +#define GPIO_MODE_AIN ((uint8_t)0x00U) /*!< analog input mode */ +#define GPIO_MODE_IN_FLOATING ((uint8_t)0x04U) /*!< floating input mode */ +#define GPIO_MODE_IPD ((uint8_t)0x28U) /*!< pull-down input mode */ +#define GPIO_MODE_IPU ((uint8_t)0x48U) /*!< pull-up input mode */ +#define GPIO_MODE_OUT_OD ((uint8_t)0x14U) /*!< GPIO output with open-drain */ +#define GPIO_MODE_OUT_PP ((uint8_t)0x10U) /*!< GPIO output with push-pull */ +#define GPIO_MODE_AF_OD ((uint8_t)0x1CU) /*!< AFIO output with open-drain */ +#define GPIO_MODE_AF_PP ((uint8_t)0x18U) /*!< AFIO output with push-pull */ + +/* GPIO output max speed value */ +#define GPIO_OSPEED_10MHZ ((uint8_t)0x01U) /*!< output max speed 10MHz */ +#define GPIO_OSPEED_2MHZ ((uint8_t)0x02U) /*!< output max speed 2MHz */ +#define GPIO_OSPEED_50MHZ ((uint8_t)0x03U) /*!< output max speed 50MHz */ + +/* GPIO event output port definitions */ +#define GPIO_EVENT_PORT_GPIOA ((uint8_t)0x00U) /*!< event output port A */ +#define GPIO_EVENT_PORT_GPIOB ((uint8_t)0x01U) /*!< event output port B */ +#define GPIO_EVENT_PORT_GPIOC ((uint8_t)0x02U) /*!< event output port C */ +#define GPIO_EVENT_PORT_GPIOD ((uint8_t)0x03U) /*!< event output port D */ +#define GPIO_EVENT_PORT_GPIOE ((uint8_t)0x04U) /*!< event output port E */ + +/* GPIO output port source definitions */ +#define GPIO_PORT_SOURCE_GPIOA ((uint8_t)0x00U) /*!< output port source A */ +#define GPIO_PORT_SOURCE_GPIOB ((uint8_t)0x01U) /*!< output port source B */ +#define GPIO_PORT_SOURCE_GPIOC ((uint8_t)0x02U) /*!< output port source C */ +#define GPIO_PORT_SOURCE_GPIOD ((uint8_t)0x03U) /*!< output port source D */ +#define GPIO_PORT_SOURCE_GPIOE ((uint8_t)0x04U) /*!< output port source E */ + +/* GPIO event output pin definitions */ +#define GPIO_EVENT_PIN_0 ((uint8_t)0x00U) /*!< GPIO event pin 0 */ +#define GPIO_EVENT_PIN_1 ((uint8_t)0x01U) /*!< GPIO event pin 1 */ +#define GPIO_EVENT_PIN_2 ((uint8_t)0x02U) /*!< GPIO event pin 2 */ +#define GPIO_EVENT_PIN_3 ((uint8_t)0x03U) /*!< GPIO event pin 3 */ +#define GPIO_EVENT_PIN_4 ((uint8_t)0x04U) /*!< GPIO event pin 4 */ +#define GPIO_EVENT_PIN_5 ((uint8_t)0x05U) /*!< GPIO event pin 5 */ +#define GPIO_EVENT_PIN_6 ((uint8_t)0x06U) /*!< GPIO event pin 6 */ +#define GPIO_EVENT_PIN_7 ((uint8_t)0x07U) /*!< GPIO event pin 7 */ +#define GPIO_EVENT_PIN_8 ((uint8_t)0x08U) /*!< GPIO event pin 8 */ +#define GPIO_EVENT_PIN_9 ((uint8_t)0x09U) /*!< GPIO event pin 9 */ +#define GPIO_EVENT_PIN_10 ((uint8_t)0x0AU) /*!< GPIO event pin 10 */ +#define GPIO_EVENT_PIN_11 ((uint8_t)0x0BU) /*!< GPIO event pin 11 */ +#define GPIO_EVENT_PIN_12 ((uint8_t)0x0CU) /*!< GPIO event pin 12 */ +#define GPIO_EVENT_PIN_13 ((uint8_t)0x0DU) /*!< GPIO event pin 13 */ +#define GPIO_EVENT_PIN_14 ((uint8_t)0x0EU) /*!< GPIO event pin 14 */ +#define GPIO_EVENT_PIN_15 ((uint8_t)0x0FU) /*!< GPIO event pin 15 */ + +/* GPIO output pin source definitions */ +#define GPIO_PIN_SOURCE_0 ((uint8_t)0x00U) /*!< GPIO pin source 0 */ +#define GPIO_PIN_SOURCE_1 ((uint8_t)0x01U) /*!< GPIO pin source 1 */ +#define GPIO_PIN_SOURCE_2 ((uint8_t)0x02U) /*!< GPIO pin source 2 */ +#define GPIO_PIN_SOURCE_3 ((uint8_t)0x03U) /*!< GPIO pin source 3 */ +#define GPIO_PIN_SOURCE_4 ((uint8_t)0x04U) /*!< GPIO pin source 4 */ +#define GPIO_PIN_SOURCE_5 ((uint8_t)0x05U) /*!< GPIO pin source 5 */ +#define GPIO_PIN_SOURCE_6 ((uint8_t)0x06U) /*!< GPIO pin source 6 */ +#define GPIO_PIN_SOURCE_7 ((uint8_t)0x07U) /*!< GPIO pin source 7 */ +#define GPIO_PIN_SOURCE_8 ((uint8_t)0x08U) /*!< GPIO pin source 8 */ +#define GPIO_PIN_SOURCE_9 ((uint8_t)0x09U) /*!< GPIO pin source 9 */ +#define GPIO_PIN_SOURCE_10 ((uint8_t)0x0AU) /*!< GPIO pin source 10 */ +#define GPIO_PIN_SOURCE_11 ((uint8_t)0x0BU) /*!< GPIO pin source 11 */ +#define GPIO_PIN_SOURCE_12 ((uint8_t)0x0CU) /*!< GPIO pin source 12 */ +#define GPIO_PIN_SOURCE_13 ((uint8_t)0x0DU) /*!< GPIO pin source 13 */ +#define GPIO_PIN_SOURCE_14 ((uint8_t)0x0EU) /*!< GPIO pin source 14 */ +#define GPIO_PIN_SOURCE_15 ((uint8_t)0x0FU) /*!< GPIO pin source 15 */ + +/* GPIO pin definitions */ +#define GPIO_PIN_0 BIT(0) /*!< GPIO pin 0 */ +#define GPIO_PIN_1 BIT(1) /*!< GPIO pin 1 */ +#define GPIO_PIN_2 BIT(2) /*!< GPIO pin 2 */ +#define GPIO_PIN_3 BIT(3) /*!< GPIO pin 3 */ +#define GPIO_PIN_4 BIT(4) /*!< GPIO pin 4 */ +#define GPIO_PIN_5 BIT(5) /*!< GPIO pin 5 */ +#define GPIO_PIN_6 BIT(6) /*!< GPIO pin 6 */ +#define GPIO_PIN_7 BIT(7) /*!< GPIO pin 7 */ +#define GPIO_PIN_8 BIT(8) /*!< GPIO pin 8 */ +#define GPIO_PIN_9 BIT(9) /*!< GPIO pin 9 */ +#define GPIO_PIN_10 BIT(10) /*!< GPIO pin 10 */ +#define GPIO_PIN_11 BIT(11) /*!< GPIO pin 11 */ +#define GPIO_PIN_12 BIT(12) /*!< GPIO pin 12 */ +#define GPIO_PIN_13 BIT(13) /*!< GPIO pin 13 */ +#define GPIO_PIN_14 BIT(14) /*!< GPIO pin 14 */ +#define GPIO_PIN_15 BIT(15) /*!< GPIO pin 15 */ +#define GPIO_PIN_ALL BITS(0, 15) /*!< GPIO pin all */ + +/* GPIO remap definitions */ +#define GPIO_SPI0_REMAP ((uint32_t)0x00000001U) /*!< SPI0 remapping */ +#define GPIO_I2C0_REMAP ((uint32_t)0x00000002U) /*!< I2C0 remapping */ +#define GPIO_USART0_REMAP ((uint32_t)0x00000004U) /*!< USART0 remapping */ +#define GPIO_USART1_REMAP ((uint32_t)0x00000008U) /*!< USART1 remapping */ +#define GPIO_USART2_PARTIAL_REMAP ((uint32_t)0x00140010U) /*!< USART2 partial remapping */ +#define GPIO_USART2_FULL_REMAP ((uint32_t)0x00140030U) /*!< USART2 full remapping */ +#define GPIO_TIMER0_PARTIAL_REMAP ((uint32_t)0x00160040U) /*!< TIMER0 partial remapping */ +#define GPIO_TIMER0_FULL_REMAP ((uint32_t)0x001600C0U) /*!< TIMER0 full remapping */ +#define GPIO_TIMER1_PARTIAL_REMAP0 ((uint32_t)0x00180100U) /*!< TIMER1 partial remapping */ +#define GPIO_TIMER1_PARTIAL_REMAP1 ((uint32_t)0x00180200U) /*!< TIMER1 partial remapping */ +#define GPIO_TIMER1_FULL_REMAP ((uint32_t)0x00180300U) /*!< TIMER1 full remapping */ +#define GPIO_TIMER2_PARTIAL_REMAP ((uint32_t)0x001A0800U) /*!< TIMER2 partial remapping */ +#define GPIO_TIMER2_FULL_REMAP ((uint32_t)0x001A0C00U) /*!< TIMER2 full remapping */ +#define GPIO_TIMER3_REMAP ((uint32_t)0x00001000U) /*!< TIMER3 remapping */ +#define GPIO_CAN0_PARTIAL_REMAP ((uint32_t)0x001D4000U) /*!< CAN0 partial remapping */ +#define GPIO_CAN0_FULL_REMAP ((uint32_t)0x001D6000U) /*!< CAN0 full remapping */ +#define GPIO_PD01_REMAP ((uint32_t)0x00008000U) /*!< PD01 remapping */ +#define GPIO_TIMER4CH3_IREMAP ((uint32_t)0x00200001U) /*!< TIMER4 channel3 internal remapping */ +#define GPIO_CAN1_REMAP ((uint32_t)0x00200040U) /*!< CAN1 remapping */ +#define GPIO_SWJ_NONJTRST_REMAP ((uint32_t)0x00300100U) /*!< JTAG-DP,but without NJTRST */ +#define GPIO_SWJ_DISABLE_REMAP ((uint32_t)0x00300200U) /*!< JTAG-DP disabled */ +#define GPIO_SPI2_REMAP ((uint32_t)0x00201100U) /*!< SPI2 remapping */ +#define GPIO_TIMER1ITI1_REMAP ((uint32_t)0x00202000U) /*!< TIMER1 internal trigger 1 remapping */ +#define GPIO_EXMC_NADV_REMAP ((uint32_t)0x80000400U) /*!< EXMC_NADV connect/disconnect */ + +/* function declarations */ +/* reset GPIO port */ +void gpio_deinit(uint32_t gpio_periph); +/* reset alternate function I/O(AFIO) */ +void gpio_afio_deinit(void); +/* GPIO parameter initialization */ +void gpio_init(uint32_t gpio_periph,uint32_t mode,uint32_t speed,uint32_t pin); + +/* set GPIO pin bit */ +void gpio_bit_set(uint32_t gpio_periph, uint32_t pin); +/* reset GPIO pin bit */ +void gpio_bit_reset(uint32_t gpio_periph, uint32_t pin); +/* write data to the specified GPIO pin */ +void gpio_bit_write(uint32_t gpio_periph, uint32_t pin, bit_status bit_value); +/* write data to the specified GPIO port */ +void gpio_port_write(uint32_t gpio_periph, uint16_t data); + +/* get GPIO pin input status */ +FlagStatus gpio_input_bit_get(uint32_t gpio_periph, uint32_t pin); +/* get GPIO port input status */ +uint16_t gpio_input_port_get(uint32_t gpio_periph); +/* get GPIO pin output status */ +FlagStatus gpio_output_bit_get(uint32_t gpio_periph, uint32_t pin); +/* get GPIO port output status */ +uint16_t gpio_output_port_get(uint32_t gpio_periph); + +/* configure GPIO pin remap */ +void gpio_pin_remap_config(uint32_t remap, ControlStatus newvalue); + +/* select GPIO pin exti sources */ +void gpio_exti_source_select(uint8_t output_port, uint8_t output_pin); +/* configure GPIO pin event output */ +void gpio_event_output_config(uint8_t output_port, uint8_t output_pin); +/* enable GPIO pin event output */ +void gpio_event_output_enable(void); +/* disable GPIO pin event output */ +void gpio_event_output_disable(void); + +/* lock GPIO pin bit */ +void gpio_pin_lock(uint32_t gpio_periph, uint32_t pin); + +#endif /* GD32VF103_GPIO_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_i2c.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_i2c.h new file mode 100644 index 00000000..0eb865b3 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_i2c.h @@ -0,0 +1,344 @@ +/*! + \file gd32vf103_i2c.h + \brief definitions for the I2C + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_I2C_H +#define GD32VF103_I2C_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* I2Cx(x=0,1) definitions */ +#define I2C0 I2C_BASE /*!< I2C0 base address */ +#define I2C1 (I2C_BASE + 0x00000400U) /*!< I2C1 base address */ + +/* registers definitions */ +#define I2C_CTL0(i2cx) REG32((i2cx) + 0x00U) /*!< I2C control register 0 */ +#define I2C_CTL1(i2cx) REG32((i2cx) + 0x04U) /*!< I2C control register 1 */ +#define I2C_SADDR0(i2cx) REG32((i2cx) + 0x08U) /*!< I2C slave address register 0*/ +#define I2C_SADDR1(i2cx) REG32((i2cx) + 0x0CU) /*!< I2C slave address register */ +#define I2C_DATA(i2cx) REG32((i2cx) + 0x10U) /*!< I2C transfer buffer register */ +#define I2C_STAT0(i2cx) REG32((i2cx) + 0x14U) /*!< I2C transfer status register 0 */ +#define I2C_STAT1(i2cx) REG32((i2cx) + 0x18U) /*!< I2C transfer status register */ +#define I2C_CKCFG(i2cx) REG32((i2cx) + 0x1CU) /*!< I2C clock configure register */ +#define I2C_RT(i2cx) REG32((i2cx) + 0x20U) /*!< I2C rise time register */ + +/* bits definitions */ +/* I2Cx_CTL0 */ +#define I2C_CTL0_I2CEN BIT(0) /*!< peripheral enable */ +#define I2C_CTL0_SMBEN BIT(1) /*!< SMBus mode */ +#define I2C_CTL0_SMBSEL BIT(3) /*!< SMBus type */ +#define I2C_CTL0_ARPEN BIT(4) /*!< ARP enable */ +#define I2C_CTL0_PECEN BIT(5) /*!< PEC enable */ +#define I2C_CTL0_GCEN BIT(6) /*!< general call enable */ +#define I2C_CTL0_SS BIT(7) /*!< clock stretching disable (slave mode) */ +#define I2C_CTL0_START BIT(8) /*!< start generation */ +#define I2C_CTL0_STOP BIT(9) /*!< stop generation */ +#define I2C_CTL0_ACKEN BIT(10) /*!< acknowledge enable */ +#define I2C_CTL0_POAP BIT(11) /*!< acknowledge/PEC position (for data reception) */ +#define I2C_CTL0_PECTRANS BIT(12) /*!< packet error checking */ +#define I2C_CTL0_SALT BIT(13) /*!< SMBus alert */ +#define I2C_CTL0_SRESET BIT(15) /*!< software reset */ + +/* I2Cx_CTL1 */ +#define I2C_CTL1_I2CCLK BITS(0,5) /*!< I2CCLK[5:0] bits (peripheral clock frequency) */ +#define I2C_CTL1_ERRIE BIT(8) /*!< error interrupt enable */ +#define I2C_CTL1_EVIE BIT(9) /*!< event interrupt enable */ +#define I2C_CTL1_BUFIE BIT(10) /*!< buffer interrupt enable */ +#define I2C_CTL1_DMAON BIT(11) /*!< DMA requests enable */ +#define I2C_CTL1_DMALST BIT(12) /*!< DMA last transfer */ + +/* I2Cx_SADDR0 */ +#define I2C_SADDR0_ADDRESS0 BIT(0) /*!< bit 0 of a 10-bit address */ +#define I2C_SADDR0_ADDRESS BITS(1,7) /*!< 7-bit address or bits 7:1 of a 10-bit address */ +#define I2C_SADDR0_ADDRESS_H BITS(8,9) /*!< highest two bits of a 10-bit address */ +#define I2C_SADDR0_ADDFORMAT BIT(15) /*!< address mode for the I2C slave */ + +/* I2Cx_SADDR1 */ +#define I2C_SADDR1_DUADEN BIT(0) /*!< aual-address mode switch */ +#define I2C_SADDR1_ADDRESS2 BITS(1,7) /*!< second I2C address for the slave in dual-address mode */ + +/* I2Cx_DATA */ +#define I2C_DATA_TRB BITS(0,7) /*!< 8-bit data register */ + +/* I2Cx_STAT0 */ +#define I2C_STAT0_SBSEND BIT(0) /*!< start bit (master mode) */ +#define I2C_STAT0_ADDSEND BIT(1) /*!< address sent (master mode)/matched (slave mode) */ +#define I2C_STAT0_BTC BIT(2) /*!< byte transfer finished */ +#define I2C_STAT0_ADD10SEND BIT(3) /*!< 10-bit header sent (master mode) */ +#define I2C_STAT0_STPDET BIT(4) /*!< stop detection (slave mode) */ +#define I2C_STAT0_RBNE BIT(6) /*!< data register not empty (receivers) */ +#define I2C_STAT0_TBE BIT(7) /*!< data register empty (transmitters) */ +#define I2C_STAT0_BERR BIT(8) /*!< bus error */ +#define I2C_STAT0_LOSTARB BIT(9) /*!< arbitration lost (master mode) */ +#define I2C_STAT0_AERR BIT(10) /*!< acknowledge failure */ +#define I2C_STAT0_OUERR BIT(11) /*!< overrun/underrun */ +#define I2C_STAT0_PECERR BIT(12) /*!< PEC error in reception */ +#define I2C_STAT0_SMBTO BIT(14) /*!< timeout signal in SMBus mode */ +#define I2C_STAT0_SMBALT BIT(15) /*!< SMBus alert status */ + +/* I2Cx_STAT1 */ +#define I2C_STAT1_MASTER BIT(0) /*!< master/slave */ +#define I2C_STAT1_I2CBSY BIT(1) /*!< bus busy */ +#define I2C_STAT1_TR BIT(2) /*!< transmitter/receiver */ +#define I2C_STAT1_RXGC BIT(4) /*!< general call address (slave mode) */ +#define I2C_STAT1_DEFSMB BIT(5) /*!< SMBus device default address (slave mode) */ +#define I2C_STAT1_HSTSMB BIT(6) /*!< SMBus host header (slave mode) */ +#define I2C_STAT1_DUMODF BIT(7) /*!< dual flag (slave mode) */ +#define I2C_STAT1_PECV BITS(8,15) /*!< packet error checking value */ + +/* I2Cx_CKCFG */ +#define I2C_CKCFG_CLKC BITS(0,11) /*!< clock control register in fast/standard mode (master mode) */ +#define I2C_CKCFG_DTCY BIT(14) /*!< fast mode duty cycle */ +#define I2C_CKCFG_FAST BIT(15) /*!< I2C speed selection in master mode */ + +/* I2Cx_RT */ +#define I2C_RT_RISETIME BITS(0,5) /*!< maximum rise time in fast/standard mode (Master mode) */ + +/* constants definitions */ +/* define the I2C bit position and its register index offset */ +#define I2C_REGIDX_BIT(regidx, bitpos) (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos)) +#define I2C_REG_VAL(i2cx, offset) (REG32((i2cx) + (((uint32_t)(offset) & 0xFFFFU) >> 6))) +#define I2C_BIT_POS(val) ((uint32_t)(val) & 0x1FU) +#define I2C_REGIDX_BIT2(regidx, bitpos, regidx2, bitpos2) (((uint32_t)(regidx2) << 22) | (uint32_t)((bitpos2) << 16)\ + | (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos))) +#define I2C_REG_VAL2(i2cx, offset) (REG32((i2cx) + ((uint32_t)(offset) >> 22))) +#define I2C_BIT_POS2(val) (((uint32_t)(val) & 0x1F0000U) >> 16) + +/* register offset */ +#define I2C_CTL1_REG_OFFSET 0x04U /*!< CTL1 register offset */ +#define I2C_STAT0_REG_OFFSET 0x14U /*!< STAT0 register offset */ +#define I2C_STAT1_REG_OFFSET 0x18U /*!< STAT1 register offset */ + +/* I2C flags */ +typedef enum { + /* flags in STAT0 register */ + I2C_FLAG_SBSEND = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 0U), /*!< start condition sent out in master mode */ + I2C_FLAG_ADDSEND = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 1U), /*!< address is sent in master mode or received and matches in slave mode */ + I2C_FLAG_BTC = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 2U), /*!< byte transmission finishes */ + I2C_FLAG_ADD10SEND = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 3U), /*!< header of 10-bit address is sent in master mode */ + I2C_FLAG_STPDET = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 4U), /*!< stop condition detected in slave mode */ + I2C_FLAG_RBNE = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 6U), /*!< I2C_DATA is not Empty during receiving */ + I2C_FLAG_TBE = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 7U), /*!< I2C_DATA is empty during transmitting */ + I2C_FLAG_BERR = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 8U), /*!< a bus error occurs indication a unexpected start or stop condition on I2C bus */ + I2C_FLAG_LOSTARB = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 9U), /*!< arbitration lost in master mode */ + I2C_FLAG_AERR = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 10U), /*!< acknowledge error */ + I2C_FLAG_OUERR = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 11U), /*!< over-run or under-run situation occurs in slave mode */ + I2C_FLAG_PECERR = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 12U), /*!< PEC error when receiving data */ + I2C_FLAG_SMBTO = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 14U), /*!< timeout signal in SMBus mode */ + I2C_FLAG_SMBALT = I2C_REGIDX_BIT(I2C_STAT0_REG_OFFSET, 15U), /*!< SMBus alert status */ + /* flags in STAT1 register */ + I2C_FLAG_MASTER = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 0U), /*!< a flag indicating whether I2C block is in master or slave mode */ + I2C_FLAG_I2CBSY = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 1U), /*!< busy flag */ + I2C_FLAG_TR = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 2U), /*!< whether the I2C is a transmitter or a receiver */ + I2C_FLAG_RXGC = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 4U), /*!< general call address (00h) received */ + I2C_FLAG_DEFSMB = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 5U), /*!< default address of SMBus device */ + I2C_FLAG_HSTSMB = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 6U), /*!< SMBus host header detected in slave mode */ + I2C_FLAG_DUMODF = I2C_REGIDX_BIT(I2C_STAT1_REG_OFFSET, 7U), /*!< dual flag in slave mode indicating which address is matched in dual-address mode */ +} i2c_flag_enum; + +/* I2C interrupt flags */ +typedef enum { + /* interrupt flags in CTL1 register */ + I2C_INT_FLAG_SBSEND = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 0U), /*!< start condition sent out in master mode interrupt flag */ + I2C_INT_FLAG_ADDSEND = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 1U), /*!< address is sent in master mode or received and matches in slave mode interrupt flag */ + I2C_INT_FLAG_BTC = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 2U), /*!< byte transmission finishes */ + I2C_INT_FLAG_ADD10SEND = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 3U), /*!< header of 10-bit address is sent in master mode interrupt flag */ + I2C_INT_FLAG_STPDET = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 4U), /*!< stop condition detected in slave mode interrupt flag */ + I2C_INT_FLAG_RBNE = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 6U), /*!< I2C_DATA is not Empty during receiving interrupt flag */ + I2C_INT_FLAG_TBE = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 9U,I2C_STAT0_REG_OFFSET, 7U), /*!< I2C_DATA is empty during transmitting interrupt flag */ + I2C_INT_FLAG_BERR = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 8U), /*!< a bus error occurs indication a unexpected start or stop condition on I2C bus interrupt flag */ + I2C_INT_FLAG_LOSTARB = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 9U), /*!< arbitration lost in master mode interrupt flag */ + I2C_INT_FLAG_AERR = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 10U), /*!< acknowledge error interrupt flag */ + I2C_INT_FLAG_OUERR = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 11U), /*!< over-run or under-run situation occurs in slave mode interrupt flag */ + I2C_INT_FLAG_PECERR = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 12U), /*!< PEC error when receiving data interrupt flag */ + I2C_INT_FLAG_SMBTO = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 14U), /*!< timeout signal in SMBus mode interrupt flag */ + I2C_INT_FLAG_SMBALT = I2C_REGIDX_BIT2(I2C_CTL1_REG_OFFSET, 8U,I2C_STAT0_REG_OFFSET, 15U), /*!< SMBus Alert status interrupt flag */ +} i2c_interrupt_flag_enum; + +/* I2C interrupt enable or disable */ +typedef enum { + /* interrupt in CTL1 register */ + I2C_INT_ERR = I2C_REGIDX_BIT(I2C_CTL1_REG_OFFSET, 8U), /*!< error interrupt enable */ + I2C_INT_EV = I2C_REGIDX_BIT(I2C_CTL1_REG_OFFSET, 9U), /*!< event interrupt enable */ + I2C_INT_BUF = I2C_REGIDX_BIT(I2C_CTL1_REG_OFFSET, 10U), /*!< buffer interrupt enable */ +} i2c_interrupt_enum; + +/* SMBus/I2C mode switch and SMBus type selection */ +#define I2C_I2CMODE_ENABLE ((uint32_t)0x00000000U) /*!< I2C mode */ +#define I2C_SMBUSMODE_ENABLE I2C_CTL0_SMBEN /*!< SMBus mode */ + +/* SMBus/I2C mode switch and SMBus type selection */ +#define I2C_SMBUS_DEVICE ((uint32_t)0x00000000U) /*!< SMBus mode device type */ +#define I2C_SMBUS_HOST I2C_CTL0_SMBSEL /*!< SMBus mode host type */ + +/* I2C transfer direction */ +#define I2C_RECEIVER ((uint32_t)0x00000001U) /*!< receiver */ +#define I2C_TRANSMITTER ((uint32_t)0xFFFFFFFEU) /*!< transmitter */ + +/* whether or not to send an ACK */ +#define I2C_ACK_DISABLE ((uint32_t)0x00000000U) /*!< ACK will be not sent */ +#define I2C_ACK_ENABLE ((uint32_t)0x00000001U) /*!< ACK will be sent */ + +/* I2C POAP position*/ +#define I2C_ACKPOS_NEXT ((uint32_t)0x00000000U) /*!< ACKEN bit decides whether or not to send ACK for the next byte */ +#define I2C_ACKPOS_CURRENT ((uint32_t)0x00000001U) /*!< ACKEN bit decides whether or not to send ACK or not for the current byte */ + +/* I2C dual-address mode switch */ +#define I2C_DUADEN_DISABLE ((uint32_t)0x00000000U) /*!< dual-address mode disabled */ +#define I2C_DUADEN_ENABLE ((uint32_t)0x00000001U) /*!< dual-address mode enabled */ + +/* whether or not to stretch SCL low */ +#define I2C_SCLSTRETCH_ENABLE ((uint32_t)0x00000000U) /*!< SCL stretching is enabled */ +#define I2C_SCLSTRETCH_DISABLE I2C_CTL0_SS /*!< SCL stretching is disabled */ + +/* whether or not to response to a general call */ +#define I2C_GCEN_ENABLE I2C_CTL0_GCEN /*!< slave will response to a general call */ +#define I2C_GCEN_DISABLE ((uint32_t)0x00000000U) /*!< slave will not response to a general call */ + +/* software reset I2C */ +#define I2C_SRESET_SET I2C_CTL0_SRESET /*!< I2C is under reset */ +#define I2C_SRESET_RESET ((uint32_t)0x00000000U) /*!< I2C is not under reset */ + +/* I2C DMA mode configure */ +/* DMA mode switch */ +#define I2C_DMA_ON I2C_CTL1_DMAON /*!< DMA mode enabled */ +#define I2C_DMA_OFF ((uint32_t)0x00000000U) /*!< DMA mode disabled */ + +/* flag indicating DMA last transfer */ +#define I2C_DMALST_ON I2C_CTL1_DMALST /*!< next DMA EOT is the last transfer */ +#define I2C_DMALST_OFF ((uint32_t)0x00000000U) /*!< next DMA EOT is not the last transfer */ + +/* I2C PEC configure */ +/* PEC enable */ +#define I2C_PEC_ENABLE I2C_CTL0_PECEN /*!< PEC calculation on */ +#define I2C_PEC_DISABLE ((uint32_t)0x00000000U) /*!< PEC calculation off */ + +/* PEC transfer */ +#define I2C_PECTRANS_ENABLE I2C_CTL0_PECTRANS /*!< transfer PEC */ +#define I2C_PECTRANS_DISABLE ((uint32_t)0x00000000U) /*!< not transfer PEC value */ + +/* I2C SMBus configure */ +/* issue or not alert through SMBA pin */ +#define I2C_SALTSEND_ENABLE I2C_CTL0_SALT /*!< issue alert through SMBA pin */ +#define I2C_SALTSEND_DISABLE ((uint32_t)0x00000000U) /*!< not issue alert through SMBA */ + +/* ARP protocol in SMBus switch */ +#define I2C_ARP_ENABLE I2C_CTL0_ARPEN /*!< ARP enable */ +#define I2C_ARP_DISABLE ((uint32_t)0x00000000U) /*!< ARP disable */ + +/* transmit I2C data */ +#define DATA_TRANS(regval) (BITS(0,7) & ((uint32_t)(regval) << 0)) + +/* receive I2C data */ +#define DATA_RECV(regval) GET_BITS((uint32_t)(regval), 0, 7) + +/* I2C duty cycle in fast mode */ +#define I2C_DTCY_2 ((uint32_t)0x00000000U) /*!< I2C fast mode Tlow/Thigh = 2 */ +#define I2C_DTCY_16_9 I2C_CKCFG_DTCY /*!< I2C fast mode Tlow/Thigh = 16/9 */ + +/* address mode for the I2C slave */ +#define I2C_ADDFORMAT_7BITS ((uint32_t)0x00000000U) /*!< address:7 bits */ +#define I2C_ADDFORMAT_10BITS I2C_SADDR0_ADDFORMAT /*!< address:10 bits */ + +/* function declarations */ +/* reset I2C */ +void i2c_deinit(uint32_t i2c_periph); +/* configure I2C clock */ +void i2c_clock_config(uint32_t i2c_periph, uint32_t clkspeed, uint32_t dutycyc); +/* configure I2C address */ +void i2c_mode_addr_config(uint32_t i2c_periph, uint32_t mode,uint32_t addformat, uint32_t addr); +/* SMBus type selection */ +void i2c_smbus_type_config(uint32_t i2c_periph, uint32_t type); +/* whether or not to send an ACK */ +void i2c_ack_config(uint32_t i2c_periph, uint32_t ack); +/* configure I2C POAP position */ +void i2c_ackpos_config(uint32_t i2c_periph, uint32_t pos); +/* master sends slave address */ +void i2c_master_addressing(uint32_t i2c_periph, uint32_t addr,uint32_t trandirection); +/* configure I2C saddress1 */ +void i2c_saddr1_config(uint32_t i2c_periph,uint32_t addr); +/* enable dual-address mode */ +void i2c_dualaddr_enable(uint32_t i2c_periph, uint32_t dualaddr); +/* disable dual-address mode */ +void i2c_dualaddr_disable(uint32_t i2c_periph); +/* enable I2C */ +void i2c_enable(uint32_t i2c_periph); +/* disable I2C */ +void i2c_disable(uint32_t i2c_periph); + +/* generate a START condition on I2C bus */ +void i2c_start_on_bus(uint32_t i2c_periph); +/* generate a STOP condition on I2C bus */ +void i2c_stop_on_bus(uint32_t i2c_periph); +/* I2C transmit data function */ +void i2c_data_transmit(uint32_t i2c_periph, uint8_t data); +/* I2C receive data function */ +uint8_t i2c_data_receive(uint32_t i2c_periph); +/* enable I2C DMA mode */ +void i2c_dma_enable(uint32_t i2c_periph, uint32_t dmastate); +/* configure whether next DMA EOT is DMA last transfer or not */ +void i2c_dma_last_transfer_config(uint32_t i2c_periph, uint32_t dmalast); +/* whether to stretch SCL low when data is not ready in slave mode */ +void i2c_stretch_scl_low_config(uint32_t i2c_periph, uint32_t stretchpara); +/* whether or not to response to a general call */ +void i2c_slave_response_to_gcall_config(uint32_t i2c_periph, uint32_t gcallpara); +/* software reset I2C */ +void i2c_software_reset_config(uint32_t i2c_periph, uint32_t sreset); + +/* I2C PEC calculation on or off */ +void i2c_pec_enable(uint32_t i2c_periph, uint32_t pecstate); +/* I2C whether to transfer PEC value */ +void i2c_pec_transfer_enable(uint32_t i2c_periph, uint32_t pecpara); +/* packet error checking value */ +uint8_t i2c_pec_value_get(uint32_t i2c_periph); +/* I2C issue alert through SMBA pin */ +void i2c_smbus_issue_alert(uint32_t i2c_periph, uint32_t smbuspara); +/* I2C ARP protocol in SMBus switch */ +void i2c_smbus_arp_enable(uint32_t i2c_periph, uint32_t arpstate); + +/* check I2C flag is set or not */ +FlagStatus i2c_flag_get(uint32_t i2c_periph, i2c_flag_enum flag); +/* clear I2C flag */ +void i2c_flag_clear(uint32_t i2c_periph, i2c_flag_enum flag); +/* enable I2C interrupt */ +void i2c_interrupt_enable(uint32_t i2c_periph, i2c_interrupt_enum interrupt); +/* disable I2C interrupt */ +void i2c_interrupt_disable(uint32_t i2c_periph, i2c_interrupt_enum interrupt); +/* check I2C interrupt flag */ +FlagStatus i2c_interrupt_flag_get(uint32_t i2c_periph,i2c_interrupt_flag_enum int_flag); +/* clear I2C interrupt flag */ +void i2c_interrupt_flag_clear(uint32_t i2c_periph,i2c_interrupt_flag_enum int_flag); + +#endif /* GD32VF103_I2C_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_libopt.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_libopt.h new file mode 100644 index 00000000..aae5adce --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_libopt.h @@ -0,0 +1,59 @@ +/*! + \file gd32vf103_libopt.h + \brief library optional for gd32vf103 + + \version 2019-6-5, V1.0.0, demo for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_LIBOPT_H +#define GD32VF103_LIBOPT_H +#include "gd32vf103.h" +#include "gd32vf103_adc.h" +#include "gd32vf103_bkp.h" +#include "gd32vf103_can.h" +#include "gd32vf103_crc.h" +#include "gd32vf103_dac.h" +#include "gd32vf103_dma.h" +#include "gd32vf103_exmc.h" +#include "gd32vf103_exti.h" +#include "gd32vf103_fmc.h" +#include "gd32vf103_gpio.h" +#include "gd32vf103_i2c.h" +#include "gd32vf103_fwdgt.h" +#include "gd32vf103_dbg.h" +#include "gd32vf103_pmu.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_rtc.h" +#include "gd32vf103_spi.h" +#include "gd32vf103_timer.h" +#include "gd32vf103_usart.h" +#include "gd32vf103_wwdgt.h" + +#endif /* GD32VF103_LIBOPT_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_pmu.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_pmu.h new file mode 100644 index 00000000..c2dea73c --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_pmu.h @@ -0,0 +1,127 @@ +/*! + \file gd32vf103_pmu.h + \brief definitions for the PMU + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_PMU_H +#define GD32VF103_PMU_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* PMU definitions */ +#define PMU PMU_BASE /*!< PMU base address */ + +/* registers definitions */ +#define PMU_CTL REG32((PMU) + 0x00U) /*!< PMU control register */ +#define PMU_CS REG32((PMU) + 0x04U) /*!< PMU control and status register */ + +/* bits definitions */ +/* PMU_CTL */ +#define PMU_CTL_LDOLP BIT(0) /*!< LDO low power mode */ +#define PMU_CTL_STBMOD BIT(1) /*!< standby mode */ +#define PMU_CTL_WURST BIT(2) /*!< wakeup flag reset */ +#define PMU_CTL_STBRST BIT(3) /*!< standby flag reset */ +#define PMU_CTL_LVDEN BIT(4) /*!< low voltage detector enable */ +#define PMU_CTL_LVDT BITS(5,7) /*!< low voltage detector threshold */ +#define PMU_CTL_BKPWEN BIT(8) /*!< backup domain write enable */ + +/* PMU_CS */ +#define PMU_CS_WUF BIT(0) /*!< wakeup flag */ +#define PMU_CS_STBF BIT(1) /*!< standby flag */ +#define PMU_CS_LVDF BIT(2) /*!< low voltage detector status flag */ +#define PMU_CS_WUPEN BIT(8) /*!< wakeup pin enable */ + +/* constants definitions */ +/* PMU low voltage detector threshold definitions */ +#define CTL_LVDT(regval) (BITS(5,7)&((uint32_t)(regval) << 5)) +#define PMU_LVDT_0 CTL_LVDT(0) /*!< voltage threshold is 2.2V */ +#define PMU_LVDT_1 CTL_LVDT(1) /*!< voltage threshold is 2.3V */ +#define PMU_LVDT_2 CTL_LVDT(2) /*!< voltage threshold is 2.4V */ +#define PMU_LVDT_3 CTL_LVDT(3) /*!< voltage threshold is 2.5V */ +#define PMU_LVDT_4 CTL_LVDT(4) /*!< voltage threshold is 2.6V */ +#define PMU_LVDT_5 CTL_LVDT(5) /*!< voltage threshold is 2.7V */ +#define PMU_LVDT_6 CTL_LVDT(6) /*!< voltage threshold is 2.8V */ +#define PMU_LVDT_7 CTL_LVDT(7) /*!< voltage threshold is 2.9V */ + +/* PMU flag definitions */ +#define PMU_FLAG_WAKEUP PMU_CS_WUF /*!< wakeup flag status */ +#define PMU_FLAG_STANDBY PMU_CS_STBF /*!< standby flag status */ +#define PMU_FLAG_LVD PMU_CS_LVDF /*!< lvd flag status */ + +/* PMU ldo definitions */ +#define PMU_LDO_NORMAL ((uint32_t)0x00000000U) /*!< LDO normal work when PMU enter deepsleep mode */ +#define PMU_LDO_LOWPOWER PMU_CTL_LDOLP /*!< LDO work at low power status when PMU enter deepsleep mode */ + +/* PMU flag reset definitions */ +#define PMU_FLAG_RESET_WAKEUP ((uint8_t)0x00U) /*!< wakeup flag reset */ +#define PMU_FLAG_RESET_STANDBY ((uint8_t)0x01U) /*!< standby flag reset */ + +/* PMU command constants definitions */ +#define WFI_CMD ((uint8_t)0x00U) /*!< use WFI command */ +#define WFE_CMD ((uint8_t)0x01U) /*!< use WFE command */ + +/* function declarations */ +/* reset PMU registers */ +void pmu_deinit(void); + +/* select low voltage detector threshold */ +void pmu_lvd_select(uint32_t lvdt_n); +/* disable PMU lvd */ +void pmu_lvd_disable(void); + +/* set PMU mode */ +/* PMU work at sleep mode */ +void pmu_to_sleepmode(uint8_t sleepmodecmd); +/* PMU work at deepsleep mode */ +void pmu_to_deepsleepmode(uint32_t ldo, uint8_t deepsleepmodecmd); +/* PMU work at standby mode */ +void pmu_to_standbymode(uint8_t standbymodecmd); +/* enable PMU wakeup pin */ +void pmu_wakeup_pin_enable(void); +/* disable PMU wakeup pin */ +void pmu_wakeup_pin_disable(void); + +/* backup related functions */ +/* enable write access to the registers in backup domain */ +void pmu_backup_write_enable(void); +/* disable write access to the registers in backup domain */ +void pmu_backup_write_disable(void); + +/* flag functions */ +/* get flag state */ +FlagStatus pmu_flag_get(uint32_t flag); +/* clear flag bit */ +void pmu_flag_clear(uint32_t flag_reset); + +#endif /* GD32VF103_PMU_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rcu.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rcu.h new file mode 100644 index 00000000..27e60ccf --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rcu.h @@ -0,0 +1,760 @@ +/*! + \file gd32vf103_rcu.h + \brief definitions for the RCU + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_RCU_H +#define GD32VF103_RCU_H + +#include "gd32vf103.h" + +/* RCU definitions */ +#define RCU RCU_BASE + +/* registers definitions */ + +#define RCU_CTL REG32(RCU + 0x00U) /*!< control register */ +#define RCU_CFG0 REG32(RCU + 0x04U) /*!< clock configuration register 0 */ +#define RCU_INT REG32(RCU + 0x08U) /*!< clock interrupt register */ +#define RCU_APB2RST REG32(RCU + 0x0CU) /*!< APB2 reset register */ +#define RCU_APB1RST REG32(RCU + 0x10U) /*!< APB1 reset register */ +#define RCU_AHBEN REG32(RCU + 0x14U) /*!< AHB1 enable register */ +#define RCU_APB2EN REG32(RCU + 0x18U) /*!< APB2 enable register */ +#define RCU_APB1EN REG32(RCU + 0x1CU) /*!< APB1 enable register */ +#define RCU_BDCTL REG32(RCU + 0x20U) /*!< backup domain control register */ +#define RCU_RSTSCK REG32(RCU + 0x24U) /*!< reset source / clock register */ +#define RCU_AHBRST REG32(RCU + 0x28U) /*!< AHB reset register */ +#define RCU_CFG1 REG32(RCU + 0x2CU) /*!< clock configuration register 1 */ +#define RCU_DSV REG32(RCU + 0x34U) /*!< deep-sleep mode voltage register */ + + +/* bits definitions */ +/* RCU_CTL */ +#define RCU_CTL_IRC8MEN BIT(0) /*!< internal high speed oscillator enable */ +#define RCU_CTL_IRC8MSTB BIT(1) /*!< IRC8M high speed internal oscillator stabilization flag */ +#define RCU_CTL_IRC8MADJ BITS(3,7) /*!< high speed internal oscillator clock trim adjust value */ +#define RCU_CTL_IRC8MCALIB BITS(8,15) /*!< high speed internal oscillator calibration value register */ +#define RCU_CTL_HXTALEN BIT(16) /*!< external high speed oscillator enable */ +#define RCU_CTL_HXTALSTB BIT(17) /*!< external crystal oscillator clock stabilization flag */ +#define RCU_CTL_HXTALBPS BIT(18) /*!< external crystal oscillator clock bypass mode enable */ +#define RCU_CTL_CKMEN BIT(19) /*!< HXTAL clock monitor enable */ +#define RCU_CTL_PLLEN BIT(24) /*!< PLL enable */ +#define RCU_CTL_PLLSTB BIT(25) /*!< PLL clock stabilization flag */ +#define RCU_CTL_PLL1EN BIT(26) /*!< PLL1 enable */ +#define RCU_CTL_PLL1STB BIT(27) /*!< PLL1 clock stabilization flag */ +#define RCU_CTL_PLL2EN BIT(28) /*!< PLL2 enable */ +#define RCU_CTL_PLL2STB BIT(29) /*!< PLL2 clock stabilization flag */ + + +#define RCU_CFG0_SCS BITS(0,1) /*!< system clock switch */ +#define RCU_CFG0_SCSS BITS(2,3) /*!< system clock switch status */ +#define RCU_CFG0_AHBPSC BITS(4,7) /*!< AHB prescaler selection */ +#define RCU_CFG0_APB1PSC BITS(8,10) /*!< APB1 prescaler selection */ +#define RCU_CFG0_APB2PSC BITS(11,13) /*!< APB2 prescaler selection */ +#define RCU_CFG0_ADCPSC BITS(14,15) /*!< ADC prescaler selection */ +#define RCU_CFG0_PLLSEL BIT(16) /*!< PLL clock source selection */ +#define RCU_CFG0_PREDV0_LSB BIT(17) /*!< the LSB of PREDV0 division factor */ +#define RCU_CFG0_PLLMF BITS(18,21) /*!< PLL clock multiplication factor */ +#define RCU_CFG0_USBFSPSC BITS(22,23) /*!< USBFS clock prescaler selection */ +#define RCU_CFG0_CKOUT0SEL BITS(24,27) /*!< CKOUT0 clock source selection */ +#define RCU_CFG0_ADCPSC_2 BIT(28) /*!< bit 2 of ADCPSC */ +#define RCU_CFG0_PLLMF_4 BIT(29) /*!< bit 4 of PLLMF */ + +/* RCU_INT */ +#define RCU_INT_IRC40KSTBIF BIT(0) /*!< IRC40K stabilization interrupt flag */ +#define RCU_INT_LXTALSTBIF BIT(1) /*!< LXTAL stabilization interrupt flag */ +#define RCU_INT_IRC8MSTBIF BIT(2) /*!< IRC8M stabilization interrupt flag */ +#define RCU_INT_HXTALSTBIF BIT(3) /*!< HXTAL stabilization interrupt flag */ +#define RCU_INT_PLLSTBIF BIT(4) /*!< PLL stabilization interrupt flag */ +#define RCU_INT_PLL1STBIF BIT(5) /*!< PLL1 stabilization interrupt flag */ +#define RCU_INT_PLL2STBIF BIT(6) /*!< PLL2 stabilization interrupt flag */ +#define RCU_INT_CKMIF BIT(7) /*!< HXTAL clock stuck interrupt flag */ +#define RCU_INT_IRC40KSTBIE BIT(8) /*!< IRC40K stabilization interrupt enable */ +#define RCU_INT_LXTALSTBIE BIT(9) /*!< LXTAL stabilization interrupt enable */ +#define RCU_INT_IRC8MSTBIE BIT(10) /*!< IRC8M stabilization interrupt enable */ +#define RCU_INT_HXTALSTBIE BIT(11) /*!< HXTAL stabilization interrupt enable */ +#define RCU_INT_PLLSTBIE BIT(12) /*!< PLL stabilization interrupt enable */ +#define RCU_INT_PLL1STBIE BIT(13) /*!< PLL1 stabilization interrupt enable */ +#define RCU_INT_PLL2STBIE BIT(14) /*!< PLL2 stabilization interrupt enable */ +#define RCU_INT_IRC40KSTBIC BIT(16) /*!< IRC40K stabilization interrupt clear */ +#define RCU_INT_LXTALSTBIC BIT(17) /*!< LXTAL stabilization interrupt clear */ +#define RCU_INT_IRC8MSTBIC BIT(18) /*!< IRC8M stabilization interrupt clear */ +#define RCU_INT_HXTALSTBIC BIT(19) /*!< HXTAL stabilization interrupt clear */ +#define RCU_INT_PLLSTBIC BIT(20) /*!< PLL stabilization interrupt clear */ +#define RCU_INT_PLL1STBIC BIT(21) /*!< PLL1 stabilization interrupt clear */ +#define RCU_INT_PLL2STBIC BIT(22) /*!< PLL2 stabilization interrupt clear */ +#define RCU_INT_CKMIC BIT(23) /*!< HXTAL clock stuck interrupt clear */ + +/* RCU_APB2RST */ +#define RCU_APB2RST_AFRST BIT(0) /*!< alternate function I/O reset */ +#define RCU_APB2RST_PARST BIT(2) /*!< GPIO port A reset */ +#define RCU_APB2RST_PBRST BIT(3) /*!< GPIO port B reset */ +#define RCU_APB2RST_PCRST BIT(4) /*!< GPIO port C reset */ +#define RCU_APB2RST_PDRST BIT(5) /*!< GPIO port D reset */ +#define RCU_APB2RST_PERST BIT(6) /*!< GPIO port E reset */ +#define RCU_APB2RST_ADC0RST BIT(9) /*!< ADC0 reset */ +#define RCU_APB2RST_ADC1RST BIT(10) /*!< ADC1 reset */ +#define RCU_APB2RST_TIMER0RST BIT(11) /*!< TIMER0 reset */ +#define RCU_APB2RST_SPI0RST BIT(12) /*!< SPI0 reset */ +#define RCU_APB2RST_USART0RST BIT(14) /*!< USART0 reset */ + +/* RCU_APB1RST */ +#define RCU_APB1RST_TIMER1RST BIT(0) /*!< TIMER1 reset */ +#define RCU_APB1RST_TIMER2RST BIT(1) /*!< TIMER2 reset */ +#define RCU_APB1RST_TIMER3RST BIT(2) /*!< TIMER3 reset */ +#define RCU_APB1RST_TIMER4RST BIT(3) /*!< TIMER4 reset */ +#define RCU_APB1RST_TIMER5RST BIT(4) /*!< TIMER5 reset */ +#define RCU_APB1RST_TIMER6RST BIT(5) /*!< TIMER6 reset */ + +#define RCU_APB1RST_WWDGTRST BIT(11) /*!< WWDGT reset */ +#define RCU_APB1RST_SPI1RST BIT(14) /*!< SPI1 reset */ +#define RCU_APB1RST_SPI2RST BIT(15) /*!< SPI2 reset */ +#define RCU_APB1RST_USART1RST BIT(17) /*!< USART1 reset */ +#define RCU_APB1RST_USART2RST BIT(18) /*!< USART2 reset */ +#define RCU_APB1RST_UART3RST BIT(19) /*!< UART3 reset */ +#define RCU_APB1RST_UART4RST BIT(20) /*!< UART4 reset */ +#define RCU_APB1RST_I2C0RST BIT(21) /*!< I2C0 reset */ +#define RCU_APB1RST_I2C1RST BIT(22) /*!< I2C1 reset */ +#define RCU_APB1RST_CAN0RST BIT(25) /*!< CAN0 reset */ +#define RCU_APB1RST_CAN1RST BIT(26) /*!< CAN1 reset */ +#define RCU_APB1RST_BKPIRST BIT(27) /*!< backup interface reset */ +#define RCU_APB1RST_PMURST BIT(28) /*!< PMU reset */ +#define RCU_APB1RST_DACRST BIT(29) /*!< DAC reset */ + +/* RCU_AHBEN */ +#define RCU_AHBEN_DMA0EN BIT(0) /*!< DMA0 clock enable */ +#define RCU_AHBEN_DMA1EN BIT(1) /*!< DMA1 clock enable */ +#define RCU_AHBEN_SRAMSPEN BIT(2) /*!< SRAM clock enable when sleep mode */ +#define RCU_AHBEN_FMCSPEN BIT(4) /*!< FMC clock enable when sleep mode */ +#define RCU_AHBEN_CRCEN BIT(6) /*!< CRC clock enable */ +#define RCU_AHBEN_EXMCEN BIT(8) /*!< EXMC clock enable */ +#define RCU_AHBEN_USBFSEN BIT(12) /*!< USBFS clock enable */ + +/* RCU_APB2EN */ +#define RCU_APB2EN_AFEN BIT(0) /*!< alternate function IO clock enable */ +#define RCU_APB2EN_PAEN BIT(2) /*!< GPIO port A clock enable */ +#define RCU_APB2EN_PBEN BIT(3) /*!< GPIO port B clock enable */ +#define RCU_APB2EN_PCEN BIT(4) /*!< GPIO port C clock enable */ +#define RCU_APB2EN_PDEN BIT(5) /*!< GPIO port D clock enable */ +#define RCU_APB2EN_PEEN BIT(6) /*!< GPIO port E clock enable */ +#define RCU_APB2EN_ADC0EN BIT(9) /*!< ADC0 clock enable */ +#define RCU_APB2EN_ADC1EN BIT(10) /*!< ADC1 clock enable */ +#define RCU_APB2EN_TIMER0EN BIT(11) /*!< TIMER0 clock enable */ +#define RCU_APB2EN_SPI0EN BIT(12) /*!< SPI0 clock enable */ +#define RCU_APB2EN_USART0EN BIT(14) /*!< USART0 clock enable */ + +/* RCU_APB1EN */ +#define RCU_APB1EN_TIMER1EN BIT(0) /*!< TIMER1 clock enable */ +#define RCU_APB1EN_TIMER2EN BIT(1) /*!< TIMER2 clock enable */ +#define RCU_APB1EN_TIMER3EN BIT(2) /*!< TIMER3 clock enable */ +#define RCU_APB1EN_TIMER4EN BIT(3) /*!< TIMER4 clock enable */ +#define RCU_APB1EN_TIMER5EN BIT(4) /*!< TIMER5 clock enable */ +#define RCU_APB1EN_TIMER6EN BIT(5) /*!< TIMER6 clock enable */ +#define RCU_APB1EN_WWDGTEN BIT(11) /*!< WWDGT clock enable */ +#define RCU_APB1EN_SPI1EN BIT(14) /*!< SPI1 clock enable */ +#define RCU_APB1EN_SPI2EN BIT(15) /*!< SPI2 clock enable */ +#define RCU_APB1EN_USART1EN BIT(17) /*!< USART1 clock enable */ +#define RCU_APB1EN_USART2EN BIT(18) /*!< USART2 clock enable */ +#define RCU_APB1EN_UART3EN BIT(19) /*!< UART3 clock enable */ +#define RCU_APB1EN_UART4EN BIT(20) /*!< UART4 clock enable */ +#define RCU_APB1EN_I2C0EN BIT(21) /*!< I2C0 clock enable */ +#define RCU_APB1EN_I2C1EN BIT(22) /*!< I2C1 clock enable */ +#define RCU_APB1EN_CAN0EN BIT(25) /*!< CAN0 clock enable */ +#define RCU_APB1EN_CAN1EN BIT(26) /*!< CAN1 clock enable */ +#define RCU_APB1EN_BKPIEN BIT(27) /*!< backup interface clock enable */ +#define RCU_APB1EN_PMUEN BIT(28) /*!< PMU clock enable */ +#define RCU_APB1EN_DACEN BIT(29) /*!< DAC clock enable */ + +/* RCU_BDCTL */ +#define RCU_BDCTL_LXTALEN BIT(0) /*!< LXTAL enable */ +#define RCU_BDCTL_LXTALSTB BIT(1) /*!< low speed crystal oscillator stabilization flag */ +#define RCU_BDCTL_LXTALBPS BIT(2) /*!< LXTAL bypass mode enable */ +#define RCU_BDCTL_RTCSRC BITS(8,9) /*!< RTC clock entry selection */ +#define RCU_BDCTL_RTCEN BIT(15) /*!< RTC clock enable */ +#define RCU_BDCTL_BKPRST BIT(16) /*!< backup domain reset */ + +/* RCU_RSTSCK */ +#define RCU_RSTSCK_IRC40KEN BIT(0) /*!< IRC40K enable */ +#define RCU_RSTSCK_IRC40KSTB BIT(1) /*!< IRC40K stabilization flag */ +#define RCU_RSTSCK_RSTFC BIT(24) /*!< reset flag clear */ +#define RCU_RSTSCK_EPRSTF BIT(26) /*!< external pin reset flag */ +#define RCU_RSTSCK_PORRSTF BIT(27) /*!< power reset flag */ +#define RCU_RSTSCK_SWRSTF BIT(28) /*!< software reset flag */ +#define RCU_RSTSCK_FWDGTRSTF BIT(29) /*!< free watchdog timer reset flag */ +#define RCU_RSTSCK_WWDGTRSTF BIT(30) /*!< window watchdog timer reset flag */ +#define RCU_RSTSCK_LPRSTF BIT(31) /*!< low-power reset flag */ + +/* RCU_AHBRST */ +#define RCU_AHBRST_USBFSRST BIT(12) /*!< USBFS reset */ + +/* RCU_CFG1 */ +#define RCU_CFG1_PREDV0 BITS(0,3) /*!< PREDV0 division factor */ +#define RCU_CFG1_PREDV1 BITS(4,7) /*!< PREDV1 division factor */ +#define RCU_CFG1_PLL1MF BITS(8,11) /*!< PLL1 clock multiplication factor */ +#define RCU_CFG1_PLL2MF BITS(12,15) /*!< PLL2 clock multiplication factor */ +#define RCU_CFG1_PREDV0SEL BIT(16) /*!< PREDV0 input clock source selection */ +#define RCU_CFG1_I2S1SEL BIT(17) /*!< I2S1 clock source selection */ +#define RCU_CFG1_I2S2SEL BIT(18) /*!< I2S2 clock source selection */ + +/* RCU_DSV */ +#define RCU_DSV_DSLPVS BITS(0,1) /*!< deep-sleep mode voltage select */ + +/* constants definitions */ + /* define value of high speed crystal oscillator (HXTAL) in Hz */ +#if !defined HXTAL_VALUE + #define HXTAL_VALUE ((uint32_t)8000000) /*!< value of the external oscillator in Hz */ + #define HXTAL_VALUE_25M HXTAL_VALUE +#endif /* high speed crystal oscillator value */ + +/* define startup timeout value of high speed crystal oscillator (HXTAL) */ +#if !defined (HXTAL_STARTUP_TIMEOUT) +#define HXTAL_STARTUP_TIMEOUT ((uint16_t)0xFFFF) +#endif /* high speed crystal oscillator startup timeout */ + +/* define value of internal 8MHz RC oscillator (IRC8M) in Hz */ +#if !defined (IRC8M_VALUE) +#define IRC8M_VALUE ((uint32_t)8000000) +#endif /* internal 8MHz RC oscillator value */ + +/* define startup timeout value of internal 8MHz RC oscillator (IRC8M) */ +#if !defined (IRC8M_STARTUP_TIMEOUT) +#define IRC8M_STARTUP_TIMEOUT ((uint16_t)0x0500) +#endif /* internal 8MHz RC oscillator startup timeout */ + +/* define value of internal 40KHz RC oscillator(IRC40K) in Hz */ +#if !defined (IRC40K_VALUE) +#define IRC40K_VALUE ((uint32_t)40000) +#endif /* internal 40KHz RC oscillator value */ + +/* define value of low speed crystal oscillator (LXTAL)in Hz */ +#if !defined (LXTAL_VALUE) +#define LXTAL_VALUE ((uint32_t)32768) +#endif /* low speed crystal oscillator value */ + +/* define clock source */ +#define SEL_IRC8M ((uint16_t)0U) +#define SEL_HXTAL ((uint16_t)1U) +#define SEL_PLL ((uint16_t)2U) + +/* define startup timeout count */ +#define OSC_STARTUP_TIMEOUT ((uint32_t)0xFFFFFU) +#define LXTAL_STARTUP_TIMEOUT ((uint32_t)0x3FFFFFFU) + +/* define the peripheral clock enable bit position and its register index offset */ +#define RCU_REGIDX_BIT(regidx, bitpos) (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos)) +#define RCU_REG_VAL(periph) (REG32(RCU + ((uint32_t)(periph) >> 6))) +#define RCU_BIT_POS(val) ((uint32_t)(val) & 0x1FU) + +/* register offset */ +/* peripherals enable */ +#define AHBEN_REG_OFFSET 0x14U /*!< AHB enable register offset */ +#define APB1EN_REG_OFFSET 0x1CU /*!< APB1 enable register offset */ +#define APB2EN_REG_OFFSET 0x18U /*!< APB2 enable register offset */ + +/* peripherals reset */ +#define AHBRST_REG_OFFSET 0x28U /*!< AHB reset register offset */ +#define APB1RST_REG_OFFSET 0x10U /*!< APB1 reset register offset */ +#define APB2RST_REG_OFFSET 0x0CU /*!< APB2 reset register offset */ +#define RSTSCK_REG_OFFSET 0x24U /*!< reset source/clock register offset */ + +/* clock control */ +#define CTL_REG_OFFSET 0x00U /*!< control register offset */ +#define BDCTL_REG_OFFSET 0x20U /*!< backup domain control register offset */ + +/* clock stabilization and stuck interrupt */ +#define INT_REG_OFFSET 0x08U /*!< clock interrupt register offset */ + +/* configuration register */ +#define CFG0_REG_OFFSET 0x04U /*!< clock configuration register 0 offset */ +#define CFG1_REG_OFFSET 0x2CU /*!< clock configuration register 1 offset */ + +/* peripheral clock enable */ +typedef enum { + /* AHB peripherals */ + RCU_DMA0 = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 0U), /*!< DMA0 clock */ + RCU_DMA1 = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 1U), /*!< DMA1 clock */ + RCU_CRC = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 6U), /*!< CRC clock */ + RCU_EXMC = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 8U), /*!< EXMC clock */ + RCU_USBFS = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 12U), /*!< USBFS clock */ + /* APB1 peripherals */ + RCU_TIMER1 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 0U), /*!< TIMER1 clock */ + RCU_TIMER2 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 1U), /*!< TIMER2 clock */ + RCU_TIMER3 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 2U), /*!< TIMER3 clock */ + RCU_TIMER4 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 3U), /*!< TIMER4 clock */ + RCU_TIMER5 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 4U), /*!< TIMER5 clock */ + RCU_TIMER6 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 5U), /*!< TIMER6 clock */ + RCU_WWDGT = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 11U), /*!< WWDGT clock */ + RCU_SPI1 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 14U), /*!< SPI1 clock */ + RCU_SPI2 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 15U), /*!< SPI2 clock */ + RCU_USART1 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 17U), /*!< USART1 clock */ + RCU_USART2 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 18U), /*!< USART2 clock */ + RCU_UART3 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 19U), /*!< UART3 clock */ + RCU_UART4 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 20U), /*!< UART4 clock */ + RCU_I2C0 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 21U), /*!< I2C0 clock */ + RCU_I2C1 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 22U), /*!< I2C1 clock */ + RCU_CAN0 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 25U), /*!< CAN0 clock */ + RCU_CAN1 = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 26U), /*!< CAN1 clock */ + RCU_BKPI = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 27U), /*!< BKPI clock */ + RCU_PMU = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 28U), /*!< PMU clock */ + RCU_DAC = RCU_REGIDX_BIT(APB1EN_REG_OFFSET, 29U), /*!< DAC clock */ + RCU_RTC = RCU_REGIDX_BIT(BDCTL_REG_OFFSET, 15U), /*!< RTC clock */ + /* APB2 peripherals */ + RCU_AF = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 0U), /*!< alternate function clock */ + RCU_GPIOA = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 2U), /*!< GPIOA clock */ + RCU_GPIOB = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 3U), /*!< GPIOB clock */ + RCU_GPIOC = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 4U), /*!< GPIOC clock */ + RCU_GPIOD = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 5U), /*!< GPIOD clock */ + RCU_GPIOE = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 6U), /*!< GPIOE clock */ + RCU_ADC0 = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 9U), /*!< ADC0 clock */ + RCU_ADC1 = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 10U), /*!< ADC1 clock */ + RCU_TIMER0 = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 11U), /*!< TIMER0 clock */ + RCU_SPI0 = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 12U), /*!< SPI0 clock */ + RCU_USART0 = RCU_REGIDX_BIT(APB2EN_REG_OFFSET, 14U), /*!< USART0 clock */ +} rcu_periph_enum; + +/* peripheral clock enable when sleep mode*/ +typedef enum { +/* AHB peripherals */ + RCU_SRAM_SLP = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 2U), /*!< SRAM clock */ + RCU_FMC_SLP = RCU_REGIDX_BIT(AHBEN_REG_OFFSET, 4U), /*!< FMC clock */ +} rcu_periph_sleep_enum; + +/* peripherals reset */ +typedef enum { + /* AHB peripherals */ + RCU_USBFSRST = RCU_REGIDX_BIT(AHBRST_REG_OFFSET, 12U), /*!< USBFS clock reset */ + /* APB1 peripherals */ + RCU_TIMER1RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 0U), /*!< TIMER1 clock reset */ + RCU_TIMER2RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 1U), /*!< TIMER2 clock reset */ + RCU_TIMER3RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 2U), /*!< TIMER3 clock reset */ + RCU_TIMER4RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 3U), /*!< TIMER4 clock reset */ + RCU_TIMER5RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 4U), /*!< TIMER5 clock reset */ + RCU_TIMER6RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 5U), /*!< TIMER6 clock reset */ + RCU_WWDGTRST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 11U), /*!< WWDGT clock reset */ + RCU_SPI1RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 14U), /*!< SPI1 clock reset */ + RCU_SPI2RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 15U), /*!< SPI2 clock reset */ + RCU_USART1RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 17U), /*!< USART1 clock reset */ + RCU_USART2RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 18U), /*!< USART2 clock reset */ + RCU_UART3RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 19U), /*!< UART3 clock reset */ + RCU_UART4RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 20U), /*!< UART4 clock reset */ + RCU_I2C0RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 21U), /*!< I2C0 clock reset */ + RCU_I2C1RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 22U), /*!< I2C1 clock reset */ + RCU_CAN0RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 25U), /*!< CAN0 clock reset */ + RCU_CAN1RST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 26U), /*!< CAN1 clock reset */ + RCU_BKPIRST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 27U), /*!< BKPI clock reset */ + RCU_PMURST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 28U), /*!< PMU clock reset */ + RCU_DACRST = RCU_REGIDX_BIT(APB1RST_REG_OFFSET, 29U), /*!< DAC clock reset */ + /* APB2 peripherals */ + RCU_AFRST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 0U), /*!< alternate function clock reset */ + RCU_GPIOARST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 2U), /*!< GPIOA clock reset */ + RCU_GPIOBRST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 3U), /*!< GPIOB clock reset */ + RCU_GPIOCRST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 4U), /*!< GPIOC clock reset */ + RCU_GPIODRST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 5U), /*!< GPIOD clock reset */ + RCU_GPIOERST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 6U), /*!< GPIOE clock reset */ + RCU_ADC0RST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 9U), /*!< ADC0 clock reset */ + RCU_ADC1RST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 10U), /*!< ADC1 clock reset */ + RCU_TIMER0RST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 11U), /*!< TIMER0 clock reset */ + RCU_SPI0RST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 12U), /*!< SPI0 clock reset */ + RCU_USART0RST = RCU_REGIDX_BIT(APB2RST_REG_OFFSET, 14U), /*!< USART0 clock reset */ +} rcu_periph_reset_enum; + +/* clock stabilization and peripheral reset flags */ +typedef enum { + /* clock stabilization flags */ + RCU_FLAG_IRC8MSTB = RCU_REGIDX_BIT(CTL_REG_OFFSET, 1U), /*!< IRC8M stabilization flags */ + RCU_FLAG_HXTALSTB = RCU_REGIDX_BIT(CTL_REG_OFFSET, 17U), /*!< HXTAL stabilization flags */ + RCU_FLAG_PLLSTB = RCU_REGIDX_BIT(CTL_REG_OFFSET, 25U), /*!< PLL stabilization flags */ + RCU_FLAG_PLL1STB = RCU_REGIDX_BIT(CTL_REG_OFFSET, 27U), /*!< PLL1 stabilization flags */ + RCU_FLAG_PLL2STB = RCU_REGIDX_BIT(CTL_REG_OFFSET, 29U), /*!< PLL2 stabilization flags */ + RCU_FLAG_LXTALSTB = RCU_REGIDX_BIT(BDCTL_REG_OFFSET, 1U), /*!< LXTAL stabilization flags */ + RCU_FLAG_IRC40KSTB = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 1U), /*!< IRC40K stabilization flags */ + /* reset source flags */ + RCU_FLAG_EPRST = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 26U), /*!< external PIN reset flags */ + RCU_FLAG_PORRST = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 27U), /*!< power reset flags */ + RCU_FLAG_SWRST = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 28U), /*!< software reset flags */ + RCU_FLAG_FWDGTRST = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 29U), /*!< FWDGT reset flags */ + RCU_FLAG_WWDGTRST = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 30U), /*!< WWDGT reset flags */ + RCU_FLAG_LPRST = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 31U), /*!< low-power reset flags */ +} rcu_flag_enum; + +/* clock stabilization and ckm interrupt flags */ +typedef enum { + RCU_INT_FLAG_IRC40KSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 0U), /*!< IRC40K stabilization interrupt flag */ + RCU_INT_FLAG_LXTALSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 1U), /*!< LXTAL stabilization interrupt flag */ + RCU_INT_FLAG_IRC8MSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 2U), /*!< IRC8M stabilization interrupt flag */ + RCU_INT_FLAG_HXTALSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 3U), /*!< HXTAL stabilization interrupt flag */ + RCU_INT_FLAG_PLLSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 4U), /*!< PLL stabilization interrupt flag */ + RCU_INT_FLAG_PLL1STB = RCU_REGIDX_BIT(INT_REG_OFFSET, 5U), /*!< PLL1 stabilization interrupt flag */ + RCU_INT_FLAG_PLL2STB = RCU_REGIDX_BIT(INT_REG_OFFSET, 6U), /*!< PLL2 stabilization interrupt flag */ + RCU_INT_FLAG_CKM = RCU_REGIDX_BIT(INT_REG_OFFSET, 7U), /*!< HXTAL clock stuck interrupt flag */ +} rcu_int_flag_enum; + +/* clock stabilization and stuck interrupt flags clear */ +typedef enum { + RCU_INT_FLAG_IRC40KSTB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 16U), /*!< IRC40K stabilization interrupt flags clear */ + RCU_INT_FLAG_LXTALSTB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 17U), /*!< LXTAL stabilization interrupt flags clear */ + RCU_INT_FLAG_IRC8MSTB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 18U), /*!< IRC8M stabilization interrupt flags clear */ + RCU_INT_FLAG_HXTALSTB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 19U), /*!< HXTAL stabilization interrupt flags clear */ + RCU_INT_FLAG_PLLSTB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 20U), /*!< PLL stabilization interrupt flags clear */ + RCU_INT_FLAG_PLL1STB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 21U), /*!< PLL1 stabilization interrupt flags clear */ + RCU_INT_FLAG_PLL2STB_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 22U), /*!< PLL2 stabilization interrupt flags clear */ + RCU_INT_FLAG_CKM_CLR = RCU_REGIDX_BIT(INT_REG_OFFSET, 23U), /*!< CKM interrupt flags clear */ +} rcu_int_flag_clear_enum; + +/* clock stabilization interrupt enable or disable */ +typedef enum { + RCU_INT_IRC40KSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 8U), /*!< IRC40K stabilization interrupt */ + RCU_INT_LXTALSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 9U), /*!< LXTAL stabilization interrupt */ + RCU_INT_IRC8MSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 10U), /*!< IRC8M stabilization interrupt */ + RCU_INT_HXTALSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 11U), /*!< HXTAL stabilization interrupt */ + RCU_INT_PLLSTB = RCU_REGIDX_BIT(INT_REG_OFFSET, 12U), /*!< PLL stabilization interrupt */ + RCU_INT_PLL1STB = RCU_REGIDX_BIT(INT_REG_OFFSET, 13U), /*!< PLL1 stabilization interrupt */ + RCU_INT_PLL2STB = RCU_REGIDX_BIT(INT_REG_OFFSET, 14U), /*!< PLL2 stabilization interrupt */ +} rcu_int_enum; + +/* oscillator types */ +typedef enum { + RCU_HXTAL = RCU_REGIDX_BIT(CTL_REG_OFFSET, 16U), /*!< HXTAL */ + RCU_LXTAL = RCU_REGIDX_BIT(BDCTL_REG_OFFSET, 0U), /*!< LXTAL */ + RCU_IRC8M = RCU_REGIDX_BIT(CTL_REG_OFFSET, 0U), /*!< IRC8M */ + RCU_IRC40K = RCU_REGIDX_BIT(RSTSCK_REG_OFFSET, 0U), /*!< IRC40K */ + RCU_PLL_CK = RCU_REGIDX_BIT(CTL_REG_OFFSET, 24U), /*!< PLL */ + RCU_PLL1_CK = RCU_REGIDX_BIT(CTL_REG_OFFSET, 26U), /*!< PLL1 */ + RCU_PLL2_CK = RCU_REGIDX_BIT(CTL_REG_OFFSET, 28U), /*!< PLL2 */ +} rcu_osci_type_enum; + +/* rcu clock frequency */ +typedef enum { + CK_SYS = 0, /*!< system clock */ + CK_AHB, /*!< AHB clock */ + CK_APB1, /*!< APB1 clock */ + CK_APB2, /*!< APB2 clock */ +} rcu_clock_freq_enum; + +/* RCU_CFG0 register bit define */ +/* system clock source select */ +#define CFG0_SCS(regval) (BITS(0,1) & ((uint32_t)(regval) << 0)) +#define RCU_CKSYSSRC_IRC8M CFG0_SCS(0) /*!< system clock source select IRC8M */ +#define RCU_CKSYSSRC_HXTAL CFG0_SCS(1) /*!< system clock source select HXTAL */ +#define RCU_CKSYSSRC_PLL CFG0_SCS(2) /*!< system clock source select PLL */ + +/* system clock source select status */ +#define CFG0_SCSS(regval) (BITS(2,3) & ((uint32_t)(regval) << 2)) +#define RCU_SCSS_IRC8M CFG0_SCSS(0) /*!< system clock source select IRC8M */ +#define RCU_SCSS_HXTAL CFG0_SCSS(1) /*!< system clock source select HXTAL */ +#define RCU_SCSS_PLL CFG0_SCSS(2) /*!< system clock source select PLLP */ + +/* AHB prescaler selection */ +#define CFG0_AHBPSC(regval) (BITS(4,7) & ((uint32_t)(regval) << 4)) +#define RCU_AHB_CKSYS_DIV1 CFG0_AHBPSC(0) /*!< AHB prescaler select CK_SYS */ +#define RCU_AHB_CKSYS_DIV2 CFG0_AHBPSC(8) /*!< AHB prescaler select CK_SYS/2 */ +#define RCU_AHB_CKSYS_DIV4 CFG0_AHBPSC(9) /*!< AHB prescaler select CK_SYS/4 */ +#define RCU_AHB_CKSYS_DIV8 CFG0_AHBPSC(10) /*!< AHB prescaler select CK_SYS/8 */ +#define RCU_AHB_CKSYS_DIV16 CFG0_AHBPSC(11) /*!< AHB prescaler select CK_SYS/16 */ +#define RCU_AHB_CKSYS_DIV64 CFG0_AHBPSC(12) /*!< AHB prescaler select CK_SYS/64 */ +#define RCU_AHB_CKSYS_DIV128 CFG0_AHBPSC(13) /*!< AHB prescaler select CK_SYS/128 */ +#define RCU_AHB_CKSYS_DIV256 CFG0_AHBPSC(14) /*!< AHB prescaler select CK_SYS/256 */ +#define RCU_AHB_CKSYS_DIV512 CFG0_AHBPSC(15) /*!< AHB prescaler select CK_SYS/512 */ + +/* APB1 prescaler selection */ +#define CFG0_APB1PSC(regval) (BITS(8,10) & ((uint32_t)(regval) << 8)) +#define RCU_APB1_CKAHB_DIV1 CFG0_APB1PSC(0) /*!< APB1 prescaler select CK_AHB */ +#define RCU_APB1_CKAHB_DIV2 CFG0_APB1PSC(4) /*!< APB1 prescaler select CK_AHB/2 */ +#define RCU_APB1_CKAHB_DIV4 CFG0_APB1PSC(5) /*!< APB1 prescaler select CK_AHB/4 */ +#define RCU_APB1_CKAHB_DIV8 CFG0_APB1PSC(6) /*!< APB1 prescaler select CK_AHB/8 */ +#define RCU_APB1_CKAHB_DIV16 CFG0_APB1PSC(7) /*!< APB1 prescaler select CK_AHB/16 */ + +/* APB2 prescaler selection */ +#define CFG0_APB2PSC(regval) (BITS(11,13) & ((uint32_t)(regval) << 11)) +#define RCU_APB2_CKAHB_DIV1 CFG0_APB2PSC(0) /*!< APB2 prescaler select CK_AHB */ +#define RCU_APB2_CKAHB_DIV2 CFG0_APB2PSC(4) /*!< APB2 prescaler select CK_AHB/2 */ +#define RCU_APB2_CKAHB_DIV4 CFG0_APB2PSC(5) /*!< APB2 prescaler select CK_AHB/4 */ +#define RCU_APB2_CKAHB_DIV8 CFG0_APB2PSC(6) /*!< APB2 prescaler select CK_AHB/8 */ +#define RCU_APB2_CKAHB_DIV16 CFG0_APB2PSC(7) /*!< APB2 prescaler select CK_AHB/16 */ + +/* ADC prescaler select */ +#define RCU_CKADC_CKAPB2_DIV2 ((uint32_t)0x00000000U) /*!< ADC prescaler select CK_APB2/2 */ +#define RCU_CKADC_CKAPB2_DIV4 ((uint32_t)0x00000001U) /*!< ADC prescaler select CK_APB2/4 */ +#define RCU_CKADC_CKAPB2_DIV6 ((uint32_t)0x00000002U) /*!< ADC prescaler select CK_APB2/6 */ +#define RCU_CKADC_CKAPB2_DIV8 ((uint32_t)0x00000003U) /*!< ADC prescaler select CK_APB2/8 */ +#define RCU_CKADC_CKAPB2_DIV12 ((uint32_t)0x00000005U) /*!< ADC prescaler select CK_APB2/12 */ +#define RCU_CKADC_CKAPB2_DIV16 ((uint32_t)0x00000007U) /*!< ADC prescaler select CK_APB2/16 */ + +/* PLL clock source selection */ +#define RCU_PLLSRC_IRC8M_DIV2 ((uint32_t)0x00000000U) /*!< IRC8M/2 clock selected as source clock of PLL */ +#define RCU_PLLSRC_HXTAL RCU_CFG0_PLLSEL /*!< HXTAL clock selected as source clock of PLL */ + +/* PLL clock multiplication factor */ +#define PLLMF_4 RCU_CFG0_PLLMF_4 /* bit 4 of PLLMF */ + +#define CFG0_PLLMF(regval) (BITS(18,21) & ((uint32_t)(regval) << 18)) +#define RCU_PLL_MUL2 CFG0_PLLMF(0) /*!< PLL source clock multiply by 2 */ +#define RCU_PLL_MUL3 CFG0_PLLMF(1) /*!< PLL source clock multiply by 3 */ +#define RCU_PLL_MUL4 CFG0_PLLMF(2) /*!< PLL source clock multiply by 4 */ +#define RCU_PLL_MUL5 CFG0_PLLMF(3) /*!< PLL source clock multiply by 5 */ +#define RCU_PLL_MUL6 CFG0_PLLMF(4) /*!< PLL source clock multiply by 6 */ +#define RCU_PLL_MUL7 CFG0_PLLMF(5) /*!< PLL source clock multiply by 7 */ +#define RCU_PLL_MUL8 CFG0_PLLMF(6) /*!< PLL source clock multiply by 8 */ +#define RCU_PLL_MUL9 CFG0_PLLMF(7) /*!< PLL source clock multiply by 9 */ +#define RCU_PLL_MUL10 CFG0_PLLMF(8) /*!< PLL source clock multiply by 10 */ +#define RCU_PLL_MUL11 CFG0_PLLMF(9) /*!< PLL source clock multiply by 11 */ +#define RCU_PLL_MUL12 CFG0_PLLMF(10) /*!< PLL source clock multiply by 12 */ +#define RCU_PLL_MUL13 CFG0_PLLMF(11) /*!< PLL source clock multiply by 13 */ +#define RCU_PLL_MUL14 CFG0_PLLMF(12) /*!< PLL source clock multiply by 14 */ +#define RCU_PLL_MUL6_5 CFG0_PLLMF(13) /*!< PLL source clock multiply by 6.5 */ +#define RCU_PLL_MUL16 CFG0_PLLMF(14) /*!< PLL source clock multiply by 16 */ +#define RCU_PLL_MUL17 (PLLMF_4 | CFG0_PLLMF(0)) /*!< PLL source clock multiply by 17 */ +#define RCU_PLL_MUL18 (PLLMF_4 | CFG0_PLLMF(1)) /*!< PLL source clock multiply by 18 */ +#define RCU_PLL_MUL19 (PLLMF_4 | CFG0_PLLMF(2)) /*!< PLL source clock multiply by 19 */ +#define RCU_PLL_MUL20 (PLLMF_4 | CFG0_PLLMF(3)) /*!< PLL source clock multiply by 20 */ +#define RCU_PLL_MUL21 (PLLMF_4 | CFG0_PLLMF(4)) /*!< PLL source clock multiply by 21 */ +#define RCU_PLL_MUL22 (PLLMF_4 | CFG0_PLLMF(5)) /*!< PLL source clock multiply by 22 */ +#define RCU_PLL_MUL23 (PLLMF_4 | CFG0_PLLMF(6)) /*!< PLL source clock multiply by 23 */ +#define RCU_PLL_MUL24 (PLLMF_4 | CFG0_PLLMF(7)) /*!< PLL source clock multiply by 24 */ +#define RCU_PLL_MUL25 (PLLMF_4 | CFG0_PLLMF(8)) /*!< PLL source clock multiply by 25 */ +#define RCU_PLL_MUL26 (PLLMF_4 | CFG0_PLLMF(9)) /*!< PLL source clock multiply by 26 */ +#define RCU_PLL_MUL27 (PLLMF_4 | CFG0_PLLMF(10)) /*!< PLL source clock multiply by 27 */ +#define RCU_PLL_MUL28 (PLLMF_4 | CFG0_PLLMF(11)) /*!< PLL source clock multiply by 28 */ +#define RCU_PLL_MUL29 (PLLMF_4 | CFG0_PLLMF(12)) /*!< PLL source clock multiply by 29 */ +#define RCU_PLL_MUL30 (PLLMF_4 | CFG0_PLLMF(13)) /*!< PLL source clock multiply by 30 */ +#define RCU_PLL_MUL31 (PLLMF_4 | CFG0_PLLMF(14)) /*!< PLL source clock multiply by 31 */ +#define RCU_PLL_MUL32 (PLLMF_4 | CFG0_PLLMF(15)) /*!< PLL source clock multiply by 32 */ + +/* USBFS prescaler select */ +#define CFG0_USBPSC(regval) (BITS(22,23) & ((uint32_t)(regval) << 22)) +#define RCU_CKUSB_CKPLL_DIV1_5 CFG0_USBPSC(0) /*!< USBFS prescaler select CK_PLL/1.5 */ +#define RCU_CKUSB_CKPLL_DIV1 CFG0_USBPSC(1) /*!< USBFS prescaler select CK_PLL/1 */ +#define RCU_CKUSB_CKPLL_DIV2_5 CFG0_USBPSC(2) /*!< USBFS prescaler select CK_PLL/2.5 */ +#define RCU_CKUSB_CKPLL_DIV2 CFG0_USBPSC(3) /*!< USBFS prescaler select CK_PLL/2 */ + +/* CKOUT0 clock source selection */ +#define CFG0_CKOUT0SEL(regval) (BITS(24,27) & ((uint32_t)(regval) << 24)) +#define RCU_CKOUT0SRC_NONE CFG0_CKOUT0SEL(0) /*!< no clock selected */ +#define RCU_CKOUT0SRC_CKSYS CFG0_CKOUT0SEL(4) /*!< system clock selected */ +#define RCU_CKOUT0SRC_IRC8M CFG0_CKOUT0SEL(5) /*!< internal 8M RC oscillator clock selected */ +#define RCU_CKOUT0SRC_HXTAL CFG0_CKOUT0SEL(6) /*!< high speed crystal oscillator clock (HXTAL) selected */ +#define RCU_CKOUT0SRC_CKPLL_DIV2 CFG0_CKOUT0SEL(7) /*!< CK_PLL/2 clock selected */ +#define RCU_CKOUT0SRC_CKPLL1 CFG0_CKOUT0SEL(8) /*!< CK_PLL1 clock selected */ +#define RCU_CKOUT0SRC_CKPLL2_DIV2 CFG0_CKOUT0SEL(9) /*!< CK_PLL2/2 clock selected */ +#define RCU_CKOUT0SRC_EXT1 CFG0_CKOUT0SEL(10) /*!< EXT1 selected */ +#define RCU_CKOUT0SRC_CKPLL2 CFG0_CKOUT0SEL(11) /*!< CK_PLL2 clock selected */ + +/* RTC clock entry selection */ +#define BDCTL_RTCSRC(regval) (BITS(8,9) & ((uint32_t)(regval) << 8)) +#define RCU_RTCSRC_NONE BDCTL_RTCSRC(0) /*!< no clock selected */ +#define RCU_RTCSRC_LXTAL BDCTL_RTCSRC(1) /*!< RTC source clock select LXTAL */ +#define RCU_RTCSRC_IRC40K BDCTL_RTCSRC(2) /*!< RTC source clock select IRC40K */ +#define RCU_RTCSRC_HXTAL_DIV_128 BDCTL_RTCSRC(3) /*!< RTC source clock select HXTAL/128 */ + +/* PREDV0 division factor */ +#define CFG1_PREDV0(regval) (BITS(0,3) & ((uint32_t)(regval) << 0)) +#define RCU_PREDV0_DIV1 CFG1_PREDV0(0) /*!< PREDV0 input source clock not divided */ +#define RCU_PREDV0_DIV2 CFG1_PREDV0(1) /*!< PREDV0 input source clock divided by 2 */ +#define RCU_PREDV0_DIV3 CFG1_PREDV0(2) /*!< PREDV0 input source clock divided by 3 */ +#define RCU_PREDV0_DIV4 CFG1_PREDV0(3) /*!< PREDV0 input source clock divided by 4 */ +#define RCU_PREDV0_DIV5 CFG1_PREDV0(4) /*!< PREDV0 input source clock divided by 5 */ +#define RCU_PREDV0_DIV6 CFG1_PREDV0(5) /*!< PREDV0 input source clock divided by 6 */ +#define RCU_PREDV0_DIV7 CFG1_PREDV0(6) /*!< PREDV0 input source clock divided by 7 */ +#define RCU_PREDV0_DIV8 CFG1_PREDV0(7) /*!< PREDV0 input source clock divided by 8 */ +#define RCU_PREDV0_DIV9 CFG1_PREDV0(8) /*!< PREDV0 input source clock divided by 9 */ +#define RCU_PREDV0_DIV10 CFG1_PREDV0(9) /*!< PREDV0 input source clock divided by 10 */ +#define RCU_PREDV0_DIV11 CFG1_PREDV0(10) /*!< PREDV0 input source clock divided by 11 */ +#define RCU_PREDV0_DIV12 CFG1_PREDV0(11) /*!< PREDV0 input source clock divided by 12 */ +#define RCU_PREDV0_DIV13 CFG1_PREDV0(12) /*!< PREDV0 input source clock divided by 13 */ +#define RCU_PREDV0_DIV14 CFG1_PREDV0(13) /*!< PREDV0 input source clock divided by 14 */ +#define RCU_PREDV0_DIV15 CFG1_PREDV0(14) /*!< PREDV0 input source clock divided by 15 */ +#define RCU_PREDV0_DIV16 CFG1_PREDV0(15) /*!< PREDV0 input source clock divided by 16 */ + +/* PREDV1 division factor */ +#define CFG1_PREDV1(regval) (BITS(4,7) & ((uint32_t)(regval) << 4)) +#define RCU_PREDV1_DIV1 CFG1_PREDV1(0) /*!< PREDV1 input source clock not divided */ +#define RCU_PREDV1_DIV2 CFG1_PREDV1(1) /*!< PREDV1 input source clock divided by 2 */ +#define RCU_PREDV1_DIV3 CFG1_PREDV1(2) /*!< PREDV1 input source clock divided by 3 */ +#define RCU_PREDV1_DIV4 CFG1_PREDV1(3) /*!< PREDV1 input source clock divided by 4 */ +#define RCU_PREDV1_DIV5 CFG1_PREDV1(4) /*!< PREDV1 input source clock divided by 5 */ +#define RCU_PREDV1_DIV6 CFG1_PREDV1(5) /*!< PREDV1 input source clock divided by 6 */ +#define RCU_PREDV1_DIV7 CFG1_PREDV1(6) /*!< PREDV1 input source clock divided by 7 */ +#define RCU_PREDV1_DIV8 CFG1_PREDV1(7) /*!< PREDV1 input source clock divided by 8 */ +#define RCU_PREDV1_DIV9 CFG1_PREDV1(8) /*!< PREDV1 input source clock divided by 9 */ +#define RCU_PREDV1_DIV10 CFG1_PREDV1(9) /*!< PREDV1 input source clock divided by 10 */ +#define RCU_PREDV1_DIV11 CFG1_PREDV1(10) /*!< PREDV1 input source clock divided by 11 */ +#define RCU_PREDV1_DIV12 CFG1_PREDV1(11) /*!< PREDV1 input source clock divided by 12 */ +#define RCU_PREDV1_DIV13 CFG1_PREDV1(12) /*!< PREDV1 input source clock divided by 13 */ +#define RCU_PREDV1_DIV14 CFG1_PREDV1(13) /*!< PREDV1 input source clock divided by 14 */ +#define RCU_PREDV1_DIV15 CFG1_PREDV1(14) /*!< PREDV1 input source clock divided by 15 */ +#define RCU_PREDV1_DIV16 CFG1_PREDV1(15) /*!< PREDV1 input source clock divided by 16 */ + +/* PLL1 clock multiplication factor */ +#define CFG1_PLL1MF(regval) (BITS(8,11) & ((uint32_t)(regval) << 8)) +#define RCU_PLL1_MUL8 CFG1_PLL1MF(6) /*!< PLL1 source clock multiply by 8 */ +#define RCU_PLL1_MUL9 CFG1_PLL1MF(7) /*!< PLL1 source clock multiply by 9 */ +#define RCU_PLL1_MUL10 CFG1_PLL1MF(8) /*!< PLL1 source clock multiply by 10 */ +#define RCU_PLL1_MUL11 CFG1_PLL1MF(9) /*!< PLL1 source clock multiply by 11 */ +#define RCU_PLL1_MUL12 CFG1_PLL1MF(10) /*!< PLL1 source clock multiply by 12 */ +#define RCU_PLL1_MUL13 CFG1_PLL1MF(11) /*!< PLL1 source clock multiply by 13 */ +#define RCU_PLL1_MUL14 CFG1_PLL1MF(12) /*!< PLL1 source clock multiply by 14 */ +#define RCU_PLL1_MUL15 CFG1_PLL1MF(13) /*!< PLL1 source clock multiply by 15 */ +#define RCU_PLL1_MUL16 CFG1_PLL1MF(14) /*!< PLL1 source clock multiply by 16 */ +#define RCU_PLL1_MUL20 CFG1_PLL1MF(15) /*!< PLL1 source clock multiply by 20 */ + +/* PLL2 clock multiplication factor */ +#define CFG1_PLL2MF(regval) (BITS(12,15) & ((uint32_t)(regval) << 12)) +#define RCU_PLL2_MUL8 CFG1_PLL2MF(6) /*!< PLL2 source clock multiply by 8 */ +#define RCU_PLL2_MUL9 CFG1_PLL2MF(7) /*!< PLL2 source clock multiply by 9 */ +#define RCU_PLL2_MUL10 CFG1_PLL2MF(8) /*!< PLL2 source clock multiply by 10 */ +#define RCU_PLL2_MUL11 CFG1_PLL2MF(9) /*!< PLL2 source clock multiply by 11 */ +#define RCU_PLL2_MUL12 CFG1_PLL2MF(10) /*!< PLL2 source clock multiply by 12 */ +#define RCU_PLL2_MUL13 CFG1_PLL2MF(11) /*!< PLL2 source clock multiply by 13 */ +#define RCU_PLL2_MUL14 CFG1_PLL2MF(12) /*!< PLL2 source clock multiply by 14 */ +#define RCU_PLL2_MUL15 CFG1_PLL2MF(13) /*!< PLL2 source clock multiply by 15 */ +#define RCU_PLL2_MUL16 CFG1_PLL2MF(14) /*!< PLL2 source clock multiply by 16 */ +#define RCU_PLL2_MUL20 CFG1_PLL2MF(15) /*!< PLL2 source clock multiply by 20 */ + + +/* PREDV0 input clock source selection */ +#define RCU_PREDV0SRC_HXTAL ((uint32_t)0x00000000U) /*!< HXTAL selected as PREDV0 input source clock */ +#define RCU_PREDV0SRC_CKPLL1 RCU_CFG1_PREDV0SEL /*!< CK_PLL1 selected as PREDV0 input source clock */ + +/* I2S1 clock source selection */ +#define RCU_I2S1SRC_CKSYS ((uint32_t)0x00000000U) /*!< system clock selected as I2S1 source clock */ +#define RCU_I2S1SRC_CKPLL2_MUL2 RCU_CFG1_I2S1SEL /*!< (CK_PLL2 x 2) selected as I2S1 source clock */ + +/* I2S2 clock source selection */ +#define RCU_I2S2SRC_CKSYS ((uint32_t)0x00000000U) /*!< system clock selected as I2S2 source clock */ +#define RCU_I2S2SRC_CKPLL2_MUL2 RCU_CFG1_I2S2SEL /*!< (CK_PLL2 x 2) selected as I2S2 source clock */ + + +/* deep-sleep mode voltage */ +#define DSV_DSLPVS(regval) (BITS(0,1) & ((uint32_t)(regval) << 0)) +#define RCU_DEEPSLEEP_V_1_2 DSV_DSLPVS(0) /*!< core voltage is 1.2V in deep-sleep mode */ +#define RCU_DEEPSLEEP_V_1_1 DSV_DSLPVS(1) /*!< core voltage is 1.1V in deep-sleep mode */ +#define RCU_DEEPSLEEP_V_1_0 DSV_DSLPVS(2) /*!< core voltage is 1.0V in deep-sleep mode */ +#define RCU_DEEPSLEEP_V_0_9 DSV_DSLPVS(3) /*!< core voltage is 0.9V in deep-sleep mode */ + +/* function declarations */ +/* initialization, peripheral clock enable/disable functions */ +/* deinitialize the RCU */ +void rcu_deinit(void); +/* enable the peripherals clock */ +void rcu_periph_clock_enable(rcu_periph_enum periph); +/* disable the peripherals clock */ +void rcu_periph_clock_disable(rcu_periph_enum periph); +/* enable the peripherals clock when sleep mode */ +void rcu_periph_clock_sleep_enable(rcu_periph_sleep_enum periph); +/* disable the peripherals clock when sleep mode */ +void rcu_periph_clock_sleep_disable(rcu_periph_sleep_enum periph); +/* reset the peripherals */ +void rcu_periph_reset_enable(rcu_periph_reset_enum periph_reset); +/* disable reset the peripheral */ +void rcu_periph_reset_disable(rcu_periph_reset_enum periph_reset); +/* reset the BKP domain */ +void rcu_bkp_reset_enable(void); +/* disable the BKP domain reset */ +void rcu_bkp_reset_disable(void); + +/* clock configuration functions */ +/* configure the system clock source */ +void rcu_system_clock_source_config(uint32_t ck_sys); +/* get the system clock source */ +uint32_t rcu_system_clock_source_get(void); +/* configure the AHB prescaler selection */ +void rcu_ahb_clock_config(uint32_t ck_ahb); +/* configure the APB1 prescaler selection */ +void rcu_apb1_clock_config(uint32_t ck_apb1); +/* configure the APB2 prescaler selection */ +void rcu_apb2_clock_config(uint32_t ck_apb2); +/* configure the CK_OUT0 clock source and divider */ +void rcu_ckout0_config(uint32_t ckout0_src); +/* configure the PLL clock source selection and PLL multiply factor */ +void rcu_pll_config(uint32_t pll_src, uint32_t pll_mul); + +/* configure the PREDV0 division factor and clock source */ +void rcu_predv0_config(uint32_t predv0_source, uint32_t predv0_div); +/* configure the PREDV1 division factor */ +void rcu_predv1_config(uint32_t predv1_div); +/* configure the PLL1 clock */ +void rcu_pll1_config(uint32_t pll_mul); +/* configure the PLL2 clock */ +void rcu_pll2_config(uint32_t pll_mul); + +/* peripheral clock configuration functions */ +/* configure the ADC division factor */ +void rcu_adc_clock_config(uint32_t adc_psc); +/* configure the USBD/USBFS prescaler factor */ +void rcu_usb_clock_config(uint32_t usb_psc); +/* configure the RTC clock source selection */ +void rcu_rtc_clock_config(uint32_t rtc_clock_source); + +/* configure the I2S1 clock source selection */ +void rcu_i2s1_clock_config(uint32_t i2s_clock_source); +/* configure the I2S2 clock source selection */ +void rcu_i2s2_clock_config(uint32_t i2s_clock_source); + +/* interrupt & flag functions */ +/* get the clock stabilization and periphral reset flags */ +FlagStatus rcu_flag_get(rcu_flag_enum flag); +/* clear the reset flag */ +void rcu_all_reset_flag_clear(void); +/* get the clock stabilization interrupt and ckm flags */ +FlagStatus rcu_interrupt_flag_get(rcu_int_flag_enum int_flag); +/* clear the interrupt flags */ +void rcu_interrupt_flag_clear(rcu_int_flag_clear_enum int_flag_clear); +/* enable the stabilization interrupt */ +void rcu_interrupt_enable(rcu_int_enum stab_int); +/* disable the stabilization interrupt */ +void rcu_interrupt_disable(rcu_int_enum stab_int); + +/* oscillator configuration functions */ +/* wait for oscillator stabilization flags is SET or oscillator startup is timeout */ +ErrStatus rcu_osci_stab_wait(rcu_osci_type_enum osci); +/* turn on the oscillator */ +void rcu_osci_on(rcu_osci_type_enum osci); +/* turn off the oscillator */ +void rcu_osci_off(rcu_osci_type_enum osci); +/* enable the oscillator bypass mode, HXTALEN or LXTALEN must be reset before it */ +void rcu_osci_bypass_mode_enable(rcu_osci_type_enum osci); +/* disable the oscillator bypass mode, HXTALEN or LXTALEN must be reset before it */ +void rcu_osci_bypass_mode_disable(rcu_osci_type_enum osci); +/* enable the HXTAL clock monitor */ +void rcu_hxtal_clock_monitor_enable(void); +/* disable the HXTAL clock monitor */ +void rcu_hxtal_clock_monitor_disable(void); + +/* set the IRC8M adjust value */ +void rcu_irc8m_adjust_value_set(uint32_t irc8m_adjval); +/* set the deep sleep mode voltage */ +void rcu_deepsleep_voltage_set(uint32_t dsvol); + +/* get the system clock, bus and peripheral clock frequency */ +uint32_t rcu_clock_freq_get(rcu_clock_freq_enum clock); + +#endif /* GD32VF103_RCU_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rtc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rtc.h new file mode 100644 index 00000000..733dcc93 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_rtc.h @@ -0,0 +1,150 @@ +/*! + \file gd32vf103_rtc.h + \brief definitions for the RTC + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_RTC_H +#define GD32VF103_RTC_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* RTC definitions */ +#define RTC RTC_BASE + +/* registers definitions */ +#define RTC_INTEN REG32(RTC + 0x00U) /*!< interrupt enable register */ +#define RTC_CTL REG32(RTC + 0x04U) /*!< control register */ +#define RTC_PSCH REG32(RTC + 0x08U) /*!< prescaler high register */ +#define RTC_PSCL REG32(RTC + 0x0CU) /*!< prescaler low register */ +#define RTC_DIVH REG32(RTC + 0x10U) /*!< divider high register */ +#define RTC_DIVL REG32(RTC + 0x14U) /*!< divider low register */ +#define RTC_CNTH REG32(RTC + 0x18U) /*!< counter high register */ +#define RTC_CNTL REG32(RTC + 0x1CU) /*!< counter low register */ +#define RTC_ALRMH REG32(RTC + 0x20U) /*!< alarm high register */ +#define RTC_ALRML REG32(RTC + 0x24U) /*!< alarm low register */ + +/* bits definitions */ +/* RTC_INTEN */ +#define RTC_INTEN_SCIE BIT(0) /*!< second interrupt enable */ +#define RTC_INTEN_ALRMIE BIT(1) /*!< alarm interrupt enable */ +#define RTC_INTEN_OVIE BIT(2) /*!< overflow interrupt enable */ + +/* RTC_CTL */ +#define RTC_CTL_SCIF BIT(0) /*!< second interrupt flag */ +#define RTC_CTL_ALRMIF BIT(1) /*!< alarm interrupt flag */ +#define RTC_CTL_OVIF BIT(2) /*!< overflow interrupt flag */ +#define RTC_CTL_RSYNF BIT(3) /*!< registers synchronized flag */ +#define RTC_CTL_CMF BIT(4) /*!< configuration mode flag */ +#define RTC_CTL_LWOFF BIT(5) /*!< last write operation finished flag */ + +/* RTC_PSCH */ +#define RTC_PSCH_PSC BITS(0,3) /*!< prescaler high value */ + +/* RTC_PSCL */ +#define RTC_PSCL_PSC BITS(0,15) /*!< prescaler low value */ + +/* RTC_DIVH */ +#define RTC_DIVH_DIV BITS(0,3) /*!< divider high value */ + +/* RTC_DIVL */ +#define RTC_DIVL_DIV BITS(0,15) /*!< divider low value */ + +/* RTC_CNTH */ +#define RTC_CNTH_CNT BITS(0,15) /*!< counter high value */ + +/* RTC_CNTL */ +#define RTC_CNTL_CNT BITS(0,15) /*!< counter low value */ + +/* RTC_ALRMH */ +#define RTC_ALRMH_ALRM BITS(0,15) /*!< alarm high value */ + +/* RTC_ALRML */ +#define RTC_ALRML_ALRM BITS(0,15) /*!< alarm low value */ + +/* constants definitions */ +/* RTC interrupt enable or disable definitions */ +#define RTC_INT_SECOND RTC_INTEN_SCIE /*!< second interrupt enable */ +#define RTC_INT_ALARM RTC_INTEN_ALRMIE /*!< alarm interrupt enable */ +#define RTC_INT_OVERFLOW RTC_INTEN_OVIE /*!< overflow interrupt enable */ + +/* RTC interrupt flag definitions */ +#define RTC_INT_FLAG_SECOND RTC_CTL_SCIF /*!< second interrupt flag */ +#define RTC_INT_FLAG_ALARM RTC_CTL_ALRMIF /*!< alarm interrupt flag */ +#define RTC_INT_FLAG_OVERFLOW RTC_CTL_OVIF /*!< overflow interrupt flag */ + +/* RTC flag definitions */ +#define RTC_FLAG_SECOND RTC_CTL_SCIF /*!< second interrupt flag */ +#define RTC_FLAG_ALARM RTC_CTL_ALRMIF /*!< alarm interrupt flag */ +#define RTC_FLAG_OVERFLOW RTC_CTL_OVIF /*!< overflow interrupt flag */ +#define RTC_FLAG_RSYN RTC_CTL_RSYNF /*!< registers synchronized flag */ +#define RTC_FLAG_LWOF RTC_CTL_LWOFF /*!< last write operation finished flag */ + +/* function declarations */ +/* initialization functions */ +/* enter RTC configuration mode */ +void rtc_configuration_mode_enter(void); +/* exit RTC configuration mode */ +void rtc_configuration_mode_exit(void); +/* set RTC counter value */ +void rtc_counter_set(uint32_t cnt); +/* set RTC prescaler value */ +void rtc_prescaler_set(uint32_t psc); + +/* operation functions */ +/* wait RTC last write operation finished flag set */ +void rtc_lwoff_wait(void); +/* wait RTC registers synchronized flag set */ +void rtc_register_sync_wait(void); +/* set RTC alarm value */ +void rtc_alarm_config(uint32_t alarm); +/* get RTC counter value */ +uint32_t rtc_counter_get(void); +/* get RTC divider value */ +uint32_t rtc_divider_get(void); + +/* flag & interrupt functions */ +/* get RTC flag status */ +FlagStatus rtc_flag_get(uint32_t flag); +/* clear RTC flag status */ +void rtc_flag_clear(uint32_t flag); +/* get RTC interrupt flag status */ +FlagStatus rtc_interrupt_flag_get(uint32_t flag); +/* clear RTC interrupt flag status */ +void rtc_interrupt_flag_clear(uint32_t flag); +/* enable RTC interrupt */ +void rtc_interrupt_enable(uint32_t interrupt); +/* disable RTC interrupt */ +void rtc_interrupt_disable(uint32_t interrupt); + +#endif /* GD32VF103_RTC_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_spi.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_spi.h new file mode 100644 index 00000000..82024f36 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_spi.h @@ -0,0 +1,343 @@ +/*! + \file gd32vf103_spi.h + \brief definitions for the SPI + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_SPI_H +#define GD32VF103_SPI_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* SPIx(x=0,1,2) definitions */ +#define SPI0 (SPI_BASE + 0x0000F800U) +#define SPI1 SPI_BASE +#define SPI2 (SPI_BASE + 0x00000400U) + +/* SPI registers definitions */ +#define SPI_CTL0(spix) REG32((spix) + 0x00U) /*!< SPI control register 0 */ +#define SPI_CTL1(spix) REG32((spix) + 0x04U) /*!< SPI control register 1*/ +#define SPI_STAT(spix) REG32((spix) + 0x08U) /*!< SPI status register */ +#define SPI_DATA(spix) REG32((spix) + 0x0CU) /*!< SPI data register */ +#define SPI_CRCPOLY(spix) REG32((spix) + 0x10U) /*!< SPI CRC polynomial register */ +#define SPI_RCRC(spix) REG32((spix) + 0x14U) /*!< SPI receive CRC register */ +#define SPI_TCRC(spix) REG32((spix) + 0x18U) /*!< SPI transmit CRC register */ +#define SPI_I2SCTL(spix) REG32((spix) + 0x1CU) /*!< SPI I2S control register */ +#define SPI_I2SPSC(spix) REG32((spix) + 0x20U) /*!< SPI I2S clock prescaler register */ + +/* bits definitions */ +/* SPI_CTL0 */ +#define SPI_CTL0_CKPH BIT(0) /*!< clock phase selection*/ +#define SPI_CTL0_CKPL BIT(1) /*!< clock polarity selection */ +#define SPI_CTL0_MSTMOD BIT(2) /*!< master mode enable */ +#define SPI_CTL0_PSC BITS(3,5) /*!< master clock prescaler selection */ +#define SPI_CTL0_SPIEN BIT(6) /*!< SPI enable*/ +#define SPI_CTL0_LF BIT(7) /*!< LSB first mode */ +#define SPI_CTL0_SWNSS BIT(8) /*!< NSS pin selection in NSS software mode */ +#define SPI_CTL0_SWNSSEN BIT(9) /*!< NSS software mode selection */ +#define SPI_CTL0_RO BIT(10) /*!< receive only */ +#define SPI_CTL0_FF16 BIT(11) /*!< data frame size */ +#define SPI_CTL0_CRCNT BIT(12) /*!< CRC next transfer */ +#define SPI_CTL0_CRCEN BIT(13) /*!< CRC calculation enable */ +#define SPI_CTL0_BDOEN BIT(14) /*!< bidirectional transmit output enable*/ +#define SPI_CTL0_BDEN BIT(15) /*!< bidirectional enable */ + +/* SPI_CTL1 */ +#define SPI_CTL1_DMAREN BIT(0) /*!< receive buffer dma enable */ +#define SPI_CTL1_DMATEN BIT(1) /*!< transmit buffer dma enable */ +#define SPI_CTL1_NSSDRV BIT(2) /*!< drive NSS output */ +#define SPI_CTL1_NSSP BIT(3) /*!< SPI NSS pulse mode enable */ +#define SPI_CTL1_TMOD BIT(4) /*!< SPI TI mode enable */ +#define SPI_CTL1_ERRIE BIT(5) /*!< errors interrupt enable */ +#define SPI_CTL1_RBNEIE BIT(6) /*!< receive buffer not empty interrupt enable */ +#define SPI_CTL1_TBEIE BIT(7) /*!< transmit buffer empty interrupt enable */ + +/* SPI_STAT */ +#define SPI_STAT_RBNE BIT(0) /*!< receive buffer not empty */ +#define SPI_STAT_TBE BIT(1) /*!< transmit buffer empty */ +#define SPI_STAT_I2SCH BIT(2) /*!< I2S channel side */ +#define SPI_STAT_TXURERR BIT(3) /*!< I2S transmission underrun error bit */ +#define SPI_STAT_CRCERR BIT(4) /*!< SPI CRC error bit */ +#define SPI_STAT_CONFERR BIT(5) /*!< SPI configuration error bit */ +#define SPI_STAT_RXORERR BIT(6) /*!< SPI reception overrun error bit */ +#define SPI_STAT_TRANS BIT(7) /*!< transmitting on-going bit */ +#define SPI_STAT_FERR BIT(8) /*!< format error bit */ + +/* SPI_DATA */ +#define SPI_DATA_DATA BITS(0,15) /*!< data transfer register */ + +/* SPI_CRCPOLY */ +#define SPI_CRCPOLY_CRCPOLY BITS(0,15) /*!< CRC polynomial value */ + +/* SPI_RCRC */ +#define SPI_RCRC_RCRC BITS(0,15) /*!< RX CRC value */ + +/* SPI_TCRC */ +#define SPI_TCRC_TCRC BITS(0,15) /*!< TX CRC value */ + +/* SPI_I2SCTL */ +#define SPI_I2SCTL_CHLEN BIT(0) /*!< channel length */ +#define SPI_I2SCTL_DTLEN BITS(1,2) /*!< data length */ +#define SPI_I2SCTL_CKPL BIT(3) /*!< idle state clock polarity */ +#define SPI_I2SCTL_I2SSTD BITS(4,5) /*!< I2S standard selection */ +#define SPI_I2SCTL_PCMSMOD BIT(7) /*!< PCM frame synchronization mode */ +#define SPI_I2SCTL_I2SOPMOD BITS(8,9) /*!< I2S operation mode */ +#define SPI_I2SCTL_I2SEN BIT(10) /*!< I2S enable */ +#define SPI_I2SCTL_I2SSEL BIT(11) /*!< I2S mode selection */ + +/* SPI_I2SPSC */ +#define SPI_I2SPSC_DIV BITS(0,7) /*!< dividing factor for the prescaler */ +#define SPI_I2SPSC_OF BIT(8) /*!< odd factor for the prescaler */ +#define SPI_I2SPSC_MCKOEN BIT(9) /*!< I2S MCK output enable */ + +/* constants definitions */ +/* SPI and I2S parameter struct definitions */ +typedef struct +{ + uint32_t device_mode; /*!< SPI master or slave */ + uint32_t trans_mode; /*!< SPI transtype */ + uint32_t frame_size; /*!< SPI frame size */ + uint32_t nss; /*!< SPI NSS control by handware or software */ + uint32_t endian; /*!< SPI big endian or little endian */ + uint32_t clock_polarity_phase; /*!< SPI clock phase and polarity */ + uint32_t prescale; /*!< SPI prescale factor */ +}spi_parameter_struct; + +/* SPI mode definitions */ +#define SPI_MASTER (SPI_CTL0_MSTMOD | SPI_CTL0_SWNSS) /*!< SPI as master */ +#define SPI_SLAVE ((uint32_t)0x00000000U) /*!< SPI as slave */ + +/* SPI bidirectional transfer direction */ +#define SPI_BIDIRECTIONAL_TRANSMIT SPI_CTL0_BDOEN /*!< SPI work in transmit-only mode */ +#define SPI_BIDIRECTIONAL_RECEIVE (~SPI_CTL0_BDOEN) /*!< SPI work in receive-only mode */ + +/* SPI transmit type */ +#define SPI_TRANSMODE_FULLDUPLEX ((uint32_t)0x00000000U) /*!< SPI receive and send data at fullduplex communication */ +#define SPI_TRANSMODE_RECEIVEONLY SPI_CTL0_RO /*!< SPI only receive data */ +#define SPI_TRANSMODE_BDRECEIVE SPI_CTL0_BDEN /*!< bidirectional receive data */ +#define SPI_TRANSMODE_BDTRANSMIT (SPI_CTL0_BDEN | SPI_CTL0_BDOEN) /*!< bidirectional transmit data*/ + +/* SPI frame size */ +#define SPI_FRAMESIZE_16BIT SPI_CTL0_FF16 /*!< SPI frame size is 16 bits */ +#define SPI_FRAMESIZE_8BIT ((uint32_t)0x00000000U) /*!< SPI frame size is 8 bits */ + +/* SPI NSS control mode */ +#define SPI_NSS_SOFT SPI_CTL0_SWNSSEN /*!< SPI NSS control by software */ +#define SPI_NSS_HARD ((uint32_t)0x00000000U) /*!< SPI NSS control by hardware */ + +/* SPI transmit way */ +#define SPI_ENDIAN_MSB ((uint32_t)0x00000000U) /*!< SPI transmit way is big endian: transmit MSB first */ +#define SPI_ENDIAN_LSB SPI_CTL0_LF /*!< SPI transmit way is little endian: transmit LSB first */ + +/* SPI clock phase and polarity */ +#define SPI_CK_PL_LOW_PH_1EDGE ((uint32_t)0x00000000U) /*!< SPI clock polarity is low level and phase is first edge */ +#define SPI_CK_PL_HIGH_PH_1EDGE SPI_CTL0_CKPL /*!< SPI clock polarity is high level and phase is first edge */ +#define SPI_CK_PL_LOW_PH_2EDGE SPI_CTL0_CKPH /*!< SPI clock polarity is low level and phase is second edge */ +#define SPI_CK_PL_HIGH_PH_2EDGE (SPI_CTL0_CKPL | SPI_CTL0_CKPH) /*!< SPI clock polarity is high level and phase is second edge */ + +/* SPI clock prescale factor */ +#define CTL0_PSC(regval) (BITS(3,5) & ((uint32_t)(regval) << 3)) +#define SPI_PSC_2 CTL0_PSC(0) /*!< SPI clock prescale factor is 2 */ +#define SPI_PSC_4 CTL0_PSC(1) /*!< SPI clock prescale factor is 4 */ +#define SPI_PSC_8 CTL0_PSC(2) /*!< SPI clock prescale factor is 8 */ +#define SPI_PSC_16 CTL0_PSC(3) /*!< SPI clock prescale factor is 16 */ +#define SPI_PSC_32 CTL0_PSC(4) /*!< SPI clock prescale factor is 32 */ +#define SPI_PSC_64 CTL0_PSC(5) /*!< SPI clock prescale factor is 64 */ +#define SPI_PSC_128 CTL0_PSC(6) /*!< SPI clock prescale factor is 128 */ +#define SPI_PSC_256 CTL0_PSC(7) /*!< SPI clock prescale factor is 256 */ + +/* I2S audio sample rate */ +#define I2S_AUDIOSAMPLE_8K ((uint32_t)8000U) /*!< I2S audio sample rate is 8KHz */ +#define I2S_AUDIOSAMPLE_11K ((uint32_t)11025U) /*!< I2S audio sample rate is 11KHz */ +#define I2S_AUDIOSAMPLE_16K ((uint32_t)16000U) /*!< I2S audio sample rate is 16KHz */ +#define I2S_AUDIOSAMPLE_22K ((uint32_t)22050U) /*!< I2S audio sample rate is 22KHz */ +#define I2S_AUDIOSAMPLE_32K ((uint32_t)32000U) /*!< I2S audio sample rate is 32KHz */ +#define I2S_AUDIOSAMPLE_44K ((uint32_t)44100U) /*!< I2S audio sample rate is 44KHz */ +#define I2S_AUDIOSAMPLE_48K ((uint32_t)48000U) /*!< I2S audio sample rate is 48KHz */ +#define I2S_AUDIOSAMPLE_96K ((uint32_t)96000U) /*!< I2S audio sample rate is 96KHz */ +#define I2S_AUDIOSAMPLE_192K ((uint32_t)192000U) /*!< I2S audio sample rate is 192KHz */ + +/* I2S frame format */ +#define I2SCTL_DTLEN(regval) (BITS(1,2) & ((uint32_t)(regval) << 1)) +#define I2S_FRAMEFORMAT_DT16B_CH16B I2SCTL_DTLEN(0) /*!< I2S data length is 16 bit and channel length is 16 bit */ +#define I2S_FRAMEFORMAT_DT16B_CH32B (I2SCTL_DTLEN(0) | SPI_I2SCTL_CHLEN) /*!< I2S data length is 16 bit and channel length is 32 bit */ +#define I2S_FRAMEFORMAT_DT24B_CH32B (I2SCTL_DTLEN(1) | SPI_I2SCTL_CHLEN) /*!< I2S data length is 24 bit and channel length is 32 bit */ +#define I2S_FRAMEFORMAT_DT32B_CH32B (I2SCTL_DTLEN(2) | SPI_I2SCTL_CHLEN) /*!< I2S data length is 32 bit and channel length is 32 bit */ + +/* I2S master clock output */ +#define I2S_MCKOUT_DISABLE ((uint32_t)0x00000000U) /*!< I2S master clock output disable */ +#define I2S_MCKOUT_ENABLE SPI_I2SPSC_MCKOEN /*!< I2S master clock output enable */ + +/* I2S operation mode */ +#define I2SCTL_I2SOPMOD(regval) (BITS(8,9) & ((uint32_t)(regval) << 8)) +#define I2S_MODE_SLAVETX I2SCTL_I2SOPMOD(0) /*!< I2S slave transmit mode */ +#define I2S_MODE_SLAVERX I2SCTL_I2SOPMOD(1) /*!< I2S slave receive mode */ +#define I2S_MODE_MASTERTX I2SCTL_I2SOPMOD(2) /*!< I2S master transmit mode */ +#define I2S_MODE_MASTERRX I2SCTL_I2SOPMOD(3) /*!< I2S master receive mode */ + +/* I2S standard */ +#define I2SCTL_I2SSTD(regval) (BITS(4,5) & ((uint32_t)(regval) << 4)) +#define I2S_STD_PHILLIPS I2SCTL_I2SSTD(0) /*!< I2S phillips standard */ +#define I2S_STD_MSB I2SCTL_I2SSTD(1) /*!< I2S MSB standard */ +#define I2S_STD_LSB I2SCTL_I2SSTD(2) /*!< I2S LSB standard */ +#define I2S_STD_PCMSHORT I2SCTL_I2SSTD(3) /*!< I2S PCM short standard */ +#define I2S_STD_PCMLONG (I2SCTL_I2SSTD(3) | SPI_I2SCTL_PCMSMOD) /*!< I2S PCM long standard */ + +/* I2S clock polarity */ +#define I2S_CKPL_LOW ((uint32_t)0x00000000U) /*!< I2S clock polarity low level */ +#define I2S_CKPL_HIGH SPI_I2SCTL_CKPL /*!< I2S clock polarity high level */ + +/* SPI DMA constants definitions */ +#define SPI_DMA_TRANSMIT ((uint8_t)0x00U) /*!< SPI transmit data use DMA */ +#define SPI_DMA_RECEIVE ((uint8_t)0x01U) /*!< SPI receive data use DMA */ + +/* SPI CRC constants definitions */ +#define SPI_CRC_TX ((uint8_t)0x00U) /*!< SPI transmit CRC value */ +#define SPI_CRC_RX ((uint8_t)0x01U) /*!< SPI receive CRC value */ + +/* SPI/I2S interrupt enable/disable constants definitions */ +#define SPI_I2S_INT_TBE ((uint8_t)0x00U) /*!< transmit buffer empty interrupt */ +#define SPI_I2S_INT_RBNE ((uint8_t)0x01U) /*!< receive buffer not empty interrupt */ +#define SPI_I2S_INT_ERR ((uint8_t)0x02U) /*!< error interrupt */ + +/* SPI/I2S interrupt flag constants definitions */ +#define SPI_I2S_INT_FLAG_TBE ((uint8_t)0x00U) /*!< transmit buffer empty interrupt flag */ +#define SPI_I2S_INT_FLAG_RBNE ((uint8_t)0x01U) /*!< receive buffer not empty interrupt flag */ +#define SPI_I2S_INT_FLAG_RXORERR ((uint8_t)0x02U) /*!< overrun interrupt flag */ +#define SPI_INT_FLAG_CONFERR ((uint8_t)0x03U) /*!< config error interrupt flag */ +#define SPI_INT_FLAG_CRCERR ((uint8_t)0x04U) /*!< CRC error interrupt flag */ +#define I2S_INT_FLAG_TXURERR ((uint8_t)0x05U) /*!< underrun error interrupt flag */ +#define SPI_I2S_INT_FLAG_FERR ((uint8_t)0x06U) /*!< format error interrupt flag */ + +/* SPI/I2S flag definitions */ +#define SPI_FLAG_RBNE SPI_STAT_RBNE /*!< receive buffer not empty flag */ +#define SPI_FLAG_TBE SPI_STAT_TBE /*!< transmit buffer empty flag */ +#define SPI_FLAG_CRCERR SPI_STAT_CRCERR /*!< CRC error flag */ +#define SPI_FLAG_CONFERR SPI_STAT_CONFERR /*!< mode config error flag */ +#define SPI_FLAG_RXORERR SPI_STAT_RXORERR /*!< receive overrun error flag */ +#define SPI_FLAG_TRANS SPI_STAT_TRANS /*!< transmit on-going flag */ +#define SPI_FLAG_FERR SPI_STAT_FERR /*!< format error interrupt flag */ +#define I2S_FLAG_RBNE SPI_STAT_RBNE /*!< receive buffer not empty flag */ +#define I2S_FLAG_TBE SPI_STAT_TBE /*!< transmit buffer empty flag */ +#define I2S_FLAG_CH SPI_STAT_I2SCH /*!< channel side flag */ +#define I2S_FLAG_TXURERR SPI_STAT_TXURERR /*!< underrun error flag */ +#define I2S_FLAG_RXORERR SPI_STAT_RXORERR /*!< overrun error flag */ +#define I2S_FLAG_TRANS SPI_STAT_TRANS /*!< transmit on-going flag */ +#define I2S_FLAG_FERR SPI_STAT_FERR /*!< format error interrupt flag */ + +/* function declarations */ +/* SPI/I2S deinitialization and initialization functions */ +/* reset SPI and I2S */ +void spi_i2s_deinit(uint32_t spi_periph); +/* initialize the parameters of SPI struct with the default values */ +void spi_struct_para_init(spi_parameter_struct* spi_struct); +/* initialize SPI parameter */ +void spi_init(uint32_t spi_periph, spi_parameter_struct* spi_struct); +/* enable SPI */ +void spi_enable(uint32_t spi_periph); +/* disable SPI */ +void spi_disable(uint32_t spi_periph); + +/* initialize I2S parameter */ +void i2s_init(uint32_t spi_periph, uint32_t mode, uint32_t standard, uint32_t ckpl); +/* configure I2S prescaler */ +void i2s_psc_config(uint32_t spi_periph, uint32_t audiosample, uint32_t frameformat, uint32_t mckout); +/* enable I2S */ +void i2s_enable(uint32_t spi_periph); +/* disable I2S */ +void i2s_disable(uint32_t spi_periph); + +/* NSS functions */ +/* enable SPI NSS output */ +void spi_nss_output_enable(uint32_t spi_periph); +/* disable SPI NSS output */ +void spi_nss_output_disable(uint32_t spi_periph); +/* SPI NSS pin high level in software mode */ +void spi_nss_internal_high(uint32_t spi_periph); +/* SPI NSS pin low level in software mode */ +void spi_nss_internal_low(uint32_t spi_periph); + +/* DMA communication */ +/* enable SPI DMA */ +void spi_dma_enable(uint32_t spi_periph, uint8_t dma); +/* disable SPI DMA */ +void spi_dma_disable(uint32_t spi_periph, uint8_t dma); + +/* normal mode communication */ +/* configure SPI/I2S data frame format */ +void spi_i2s_data_frame_format_config(uint32_t spi_periph, uint16_t frame_format); +/* SPI transmit data */ +void spi_i2s_data_transmit(uint32_t spi_periph, uint16_t data); +/* SPI receive data */ +uint16_t spi_i2s_data_receive(uint32_t spi_periph); +/* configure SPI bidirectional transfer direction */ +void spi_bidirectional_transfer_config(uint32_t spi_periph, uint32_t transfer_direction); + +/* SPI CRC functions */ +/* set SPI CRC polynomial */ +void spi_crc_polynomial_set(uint32_t spi_periph, uint16_t crc_poly); +/* get SPI CRC polynomial */ +uint16_t spi_crc_polynomial_get(uint32_t spi_periph); +/* turn on SPI CRC function */ +void spi_crc_on(uint32_t spi_periph); +/* turn off SPI CRC function */ +void spi_crc_off(uint32_t spi_periph); +/* SPI next data is CRC value */ +void spi_crc_next(uint32_t spi_periph); +/* get SPI CRC send value or receive value */ +uint16_t spi_crc_get(uint32_t spi_periph, uint8_t crc); + +/* SPI TI mode functions */ +/* enable SPI TI mode */ +void spi_ti_mode_enable(uint32_t spi_periph); +/* disable SPI TI mode */ +void spi_ti_mode_disable(uint32_t spi_periph); + +/* SPI NSS pulse mode functions */ +/* enable SPI NSS pulse mode */ +void spi_nssp_mode_enable(uint32_t spi_periph); +/* disable SPI NSS pulse mode */ +void spi_nssp_mode_disable(uint32_t spi_periph); +/* flag and interrupt functions */ +/* enable SPI and I2S interrupt */ +void spi_i2s_interrupt_enable(uint32_t spi_periph, uint8_t interrupt); +/* disable SPI and I2S interrupt */ +void spi_i2s_interrupt_disable(uint32_t spi_periph, uint8_t interrupt); +/* get SPI and I2S interrupt status */ +FlagStatus spi_i2s_interrupt_flag_get(uint32_t spi_periph, uint8_t interrupt); +/* get SPI and I2S flag status */ +FlagStatus spi_i2s_flag_get(uint32_t spi_periph, uint32_t flag); +/* clear SPI CRC error flag status */ +void spi_crc_error_clear(uint32_t spi_periph); + +#endif /* GD32VF103_SPI_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_timer.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_timer.h new file mode 100644 index 00000000..c76474ae --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_timer.h @@ -0,0 +1,724 @@ +/*! + \file gd32vf103_timer.h + \brief definitions for the TIMER + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_TIMER_H +#define GD32VF103_TIMER_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* TIMERx(x=0..13) definitions */ +#define TIMER0 (TIMER_BASE + 0x00012C00U) +#define TIMER1 (TIMER_BASE + 0x00000000U) +#define TIMER2 (TIMER_BASE + 0x00000400U) +#define TIMER3 (TIMER_BASE + 0x00000800U) +#define TIMER4 (TIMER_BASE + 0x00000C00U) +#define TIMER5 (TIMER_BASE + 0x00001000U) +#define TIMER6 (TIMER_BASE + 0x00001400U) + +/* registers definitions */ +#define TIMER_CTL0(timerx) REG32((timerx) + 0x00U) /*!< TIMER control register 0 */ +#define TIMER_CTL1(timerx) REG32((timerx) + 0x04U) /*!< TIMER control register 1 */ +#define TIMER_SMCFG(timerx) REG32((timerx) + 0x08U) /*!< TIMER slave mode configuration register */ +#define TIMER_DMAINTEN(timerx) REG32((timerx) + 0x0CU) /*!< TIMER DMA and interrupt enable register */ +#define TIMER_INTF(timerx) REG32((timerx) + 0x10U) /*!< TIMER interrupt flag register */ +#define TIMER_SWEVG(timerx) REG32((timerx) + 0x14U) /*!< TIMER software event generation register */ +#define TIMER_CHCTL0(timerx) REG32((timerx) + 0x18U) /*!< TIMER channel control register 0 */ +#define TIMER_CHCTL1(timerx) REG32((timerx) + 0x1CU) /*!< TIMER channel control register 1 */ +#define TIMER_CHCTL2(timerx) REG32((timerx) + 0x20U) /*!< TIMER channel control register 2 */ +#define TIMER_CNT(timerx) REG32((timerx) + 0x24U) /*!< TIMER counter register */ +#define TIMER_PSC(timerx) REG32((timerx) + 0x28U) /*!< TIMER prescaler register */ +#define TIMER_CAR(timerx) REG32((timerx) + 0x2CU) /*!< TIMER counter auto reload register */ +#define TIMER_CREP(timerx) REG32((timerx) + 0x30U) /*!< TIMER counter repetition register */ +#define TIMER_CH0CV(timerx) REG32((timerx) + 0x34U) /*!< TIMER channel 0 capture/compare value register */ +#define TIMER_CH1CV(timerx) REG32((timerx) + 0x38U) /*!< TIMER channel 1 capture/compare value register */ +#define TIMER_CH2CV(timerx) REG32((timerx) + 0x3CU) /*!< TIMER channel 2 capture/compare value register */ +#define TIMER_CH3CV(timerx) REG32((timerx) + 0x40U) /*!< TIMER channel 3 capture/compare value register */ +#define TIMER_CCHP(timerx) REG32((timerx) + 0x44U) /*!< TIMER channel complementary protection register */ +#define TIMER_DMACFG(timerx) REG32((timerx) + 0x48U) /*!< TIMER DMA configuration register */ +#define TIMER_DMATB(timerx) REG32((timerx) + 0x4CU) /*!< TIMER DMA transfer buffer register */ + +/* bits definitions */ +/* TIMER_CTL0 */ +#define TIMER_CTL0_CEN BIT(0) /*!< TIMER counter enable */ +#define TIMER_CTL0_UPDIS BIT(1) /*!< update disable */ +#define TIMER_CTL0_UPS BIT(2) /*!< update source */ +#define TIMER_CTL0_SPM BIT(3) /*!< single pulse mode */ +#define TIMER_CTL0_DIR BIT(4) /*!< timer counter direction */ +#define TIMER_CTL0_CAM BITS(5,6) /*!< center-aligned mode selection */ +#define TIMER_CTL0_ARSE BIT(7) /*!< auto-reload shadow enable */ +#define TIMER_CTL0_CKDIV BITS(8,9) /*!< clock division */ + +/* TIMER_CTL1 */ +#define TIMER_CTL1_CCSE BIT(0) /*!< commutation control shadow enable */ +#define TIMER_CTL1_CCUC BIT(2) /*!< commutation control shadow register update control */ +#define TIMER_CTL1_DMAS BIT(3) /*!< DMA request source selection */ +#define TIMER_CTL1_MMC BITS(4,6) /*!< master mode control */ +#define TIMER_CTL1_TI0S BIT(7) /*!< channel 0 trigger input selection(hall mode selection) */ +#define TIMER_CTL1_ISO0 BIT(8) /*!< idle state of channel 0 output */ +#define TIMER_CTL1_ISO0N BIT(9) /*!< idle state of channel 0 complementary output */ +#define TIMER_CTL1_ISO1 BIT(10) /*!< idle state of channel 1 output */ +#define TIMER_CTL1_ISO1N BIT(11) /*!< idle state of channel 1 complementary output */ +#define TIMER_CTL1_ISO2 BIT(12) /*!< idle state of channel 2 output */ +#define TIMER_CTL1_ISO2N BIT(13) /*!< idle state of channel 2 complementary output */ +#define TIMER_CTL1_ISO3 BIT(14) /*!< idle state of channel 3 output */ + +/* TIMER_SMCFG */ +#define TIMER_SMCFG_SMC BITS(0,2) /*!< slave mode control */ +#define TIMER_SMCFG_TRGS BITS(4,6) /*!< trigger selection */ +#define TIMER_SMCFG_MSM BIT(7) /*!< master-slave mode */ +#define TIMER_SMCFG_ETFC BITS(8,11) /*!< external trigger filter control */ +#define TIMER_SMCFG_ETPSC BITS(12,13) /*!< external trigger prescaler */ +#define TIMER_SMCFG_SMC1 BIT(14) /*!< part of SMC for enable external clock mode 1 */ +#define TIMER_SMCFG_ETP BIT(15) /*!< external trigger polarity */ + +/* TIMER_DMAINTEN */ +#define TIMER_DMAINTEN_UPIE BIT(0) /*!< update interrupt enable */ +#define TIMER_DMAINTEN_CH0IE BIT(1) /*!< channel 0 capture/compare interrupt enable */ +#define TIMER_DMAINTEN_CH1IE BIT(2) /*!< channel 1 capture/compare interrupt enable */ +#define TIMER_DMAINTEN_CH2IE BIT(3) /*!< channel 2 capture/compare interrupt enable */ +#define TIMER_DMAINTEN_CH3IE BIT(4) /*!< channel 3 capture/compare interrupt enable */ +#define TIMER_DMAINTEN_CMTIE BIT(5) /*!< commutation interrupt request enable */ +#define TIMER_DMAINTEN_TRGIE BIT(6) /*!< trigger interrupt enable */ +#define TIMER_DMAINTEN_BRKIE BIT(7) /*!< break interrupt enable */ +#define TIMER_DMAINTEN_UPDEN BIT(8) /*!< update DMA request enable */ +#define TIMER_DMAINTEN_CH0DEN BIT(9) /*!< channel 0 capture/compare DMA request enable */ +#define TIMER_DMAINTEN_CH1DEN BIT(10) /*!< channel 1 capture/compare DMA request enable */ +#define TIMER_DMAINTEN_CH2DEN BIT(11) /*!< channel 2 capture/compare DMA request enable */ +#define TIMER_DMAINTEN_CH3DEN BIT(12) /*!< channel 3 capture/compare DMA request enable */ +#define TIMER_DMAINTEN_CMTDEN BIT(13) /*!< commutation DMA request enable */ +#define TIMER_DMAINTEN_TRGDEN BIT(14) /*!< trigger DMA request enable */ + +/* TIMER_INTF */ +#define TIMER_INTF_UPIF BIT(0) /*!< update interrupt flag */ +#define TIMER_INTF_CH0IF BIT(1) /*!< channel 0 capture/compare interrupt flag */ +#define TIMER_INTF_CH1IF BIT(2) /*!< channel 1 capture/compare interrupt flag */ +#define TIMER_INTF_CH2IF BIT(3) /*!< channel 2 capture/compare interrupt flag */ +#define TIMER_INTF_CH3IF BIT(4) /*!< channel 3 capture/compare interrupt flag */ +#define TIMER_INTF_CMTIF BIT(5) /*!< channel commutation interrupt flag */ +#define TIMER_INTF_TRGIF BIT(6) /*!< trigger interrupt flag */ +#define TIMER_INTF_BRKIF BIT(7) /*!< break interrupt flag */ +#define TIMER_INTF_CH0OF BIT(9) /*!< channel 0 over capture flag */ +#define TIMER_INTF_CH1OF BIT(10) /*!< channel 1 over capture flag */ +#define TIMER_INTF_CH2OF BIT(11) /*!< channel 2 over capture flag */ +#define TIMER_INTF_CH3OF BIT(12) /*!< channel 3 over capture flag */ + +/* TIMER_SWEVG */ +#define TIMER_SWEVG_UPG BIT(0) /*!< update event generate */ +#define TIMER_SWEVG_CH0G BIT(1) /*!< channel 0 capture or compare event generation */ +#define TIMER_SWEVG_CH1G BIT(2) /*!< channel 1 capture or compare event generation */ +#define TIMER_SWEVG_CH2G BIT(3) /*!< channel 2 capture or compare event generation */ +#define TIMER_SWEVG_CH3G BIT(4) /*!< channel 3 capture or compare event generation */ +#define TIMER_SWEVG_CMTG BIT(5) /*!< channel commutation event generation */ +#define TIMER_SWEVG_TRGG BIT(6) /*!< trigger event generation */ +#define TIMER_SWEVG_BRKG BIT(7) /*!< break event generation */ + +/* TIMER_CHCTL0 */ +/* output compare mode */ +#define TIMER_CHCTL0_CH0MS BITS(0,1) /*!< channel 0 mode selection */ +#define TIMER_CHCTL0_CH0COMFEN BIT(2) /*!< channel 0 output compare fast enable */ +#define TIMER_CHCTL0_CH0COMSEN BIT(3) /*!< channel 0 output compare shadow enable */ +#define TIMER_CHCTL0_CH0COMCTL BITS(4,6) /*!< channel 0 output compare control */ +#define TIMER_CHCTL0_CH0COMCEN BIT(7) /*!< channel 0 output compare clear enable */ +#define TIMER_CHCTL0_CH1MS BITS(8,9) /*!< channel 1 mode selection */ +#define TIMER_CHCTL0_CH1COMFEN BIT(10) /*!< channel 1 output compare fast enable */ +#define TIMER_CHCTL0_CH1COMSEN BIT(11) /*!< channel 1 output compare shadow enable */ +#define TIMER_CHCTL0_CH1COMCTL BITS(12,14) /*!< channel 1 output compare control */ +#define TIMER_CHCTL0_CH1COMCEN BIT(15) /*!< channel 1 output compare clear enable */ +/* input capture mode */ +#define TIMER_CHCTL0_CH0CAPPSC BITS(2,3) /*!< channel 0 input capture prescaler */ +#define TIMER_CHCTL0_CH0CAPFLT BITS(4,7) /*!< channel 0 input capture filter control */ +#define TIMER_CHCTL0_CH1CAPPSC BITS(10,11) /*!< channel 1 input capture prescaler */ +#define TIMER_CHCTL0_CH1CAPFLT BITS(12,15) /*!< channel 1 input capture filter control */ + +/* TIMER_CHCTL1 */ +/* output compare mode */ +#define TIMER_CHCTL1_CH2MS BITS(0,1) /*!< channel 2 mode selection */ +#define TIMER_CHCTL1_CH2COMFEN BIT(2) /*!< channel 2 output compare fast enable */ +#define TIMER_CHCTL1_CH2COMSEN BIT(3) /*!< channel 2 output compare shadow enable */ +#define TIMER_CHCTL1_CH2COMCTL BITS(4,6) /*!< channel 2 output compare control */ +#define TIMER_CHCTL1_CH2COMCEN BIT(7) /*!< channel 2 output compare clear enable */ +#define TIMER_CHCTL1_CH3MS BITS(8,9) /*!< channel 3 mode selection */ +#define TIMER_CHCTL1_CH3COMFEN BIT(10) /*!< channel 3 output compare fast enable */ +#define TIMER_CHCTL1_CH3COMSEN BIT(11) /*!< channel 3 output compare shadow enable */ +#define TIMER_CHCTL1_CH3COMCTL BITS(12,14) /*!< channel 3 output compare control */ +#define TIMER_CHCTL1_CH3COMCEN BIT(15) /*!< channel 3 output compare clear enable */ +/* input capture mode */ +#define TIMER_CHCTL1_CH2CAPPSC BITS(2,3) /*!< channel 2 input capture prescaler */ +#define TIMER_CHCTL1_CH2CAPFLT BITS(4,7) /*!< channel 2 input capture filter control */ +#define TIMER_CHCTL1_CH3CAPPSC BITS(10,11) /*!< channel 3 input capture prescaler */ +#define TIMER_CHCTL1_CH3CAPFLT BITS(12,15) /*!< channel 3 input capture filter control */ + +/* TIMER_CHCTL2 */ +#define TIMER_CHCTL2_CH0EN BIT(0) /*!< channel 0 capture/compare function enable */ +#define TIMER_CHCTL2_CH0P BIT(1) /*!< channel 0 capture/compare function polarity */ +#define TIMER_CHCTL2_CH0NEN BIT(2) /*!< channel 0 complementary output enable */ +#define TIMER_CHCTL2_CH0NP BIT(3) /*!< channel 0 complementary output polarity */ +#define TIMER_CHCTL2_CH1EN BIT(4) /*!< channel 1 capture/compare function enable */ +#define TIMER_CHCTL2_CH1P BIT(5) /*!< channel 1 capture/compare function polarity */ +#define TIMER_CHCTL2_CH1NEN BIT(6) /*!< channel 1 complementary output enable */ +#define TIMER_CHCTL2_CH1NP BIT(7) /*!< channel 1 complementary output polarity */ +#define TIMER_CHCTL2_CH2EN BIT(8) /*!< channel 2 capture/compare function enable */ +#define TIMER_CHCTL2_CH2P BIT(9) /*!< channel 2 capture/compare function polarity */ +#define TIMER_CHCTL2_CH2NEN BIT(10) /*!< channel 2 complementary output enable */ +#define TIMER_CHCTL2_CH2NP BIT(11) /*!< channel 2 complementary output polarity */ +#define TIMER_CHCTL2_CH3EN BIT(12) /*!< channel 3 capture/compare function enable */ +#define TIMER_CHCTL2_CH3P BIT(13) /*!< channel 3 capture/compare function polarity */ + +/* TIMER_CNT */ +#define TIMER_CNT_CNT BITS(0,15) /*!< 16 bit timer counter */ + +/* TIMER_PSC */ +#define TIMER_PSC_PSC BITS(0,15) /*!< prescaler value of the counter clock */ + +/* TIMER_CAR */ +#define TIMER_CAR_CARL BITS(0,15) /*!< 16 bit counter auto reload value */ + +/* TIMER_CREP */ +#define TIMER_CREP_CREP BITS(0,7) /*!< counter repetition value */ + +/* TIMER_CH0CV */ +#define TIMER_CH0CV_CH0VAL BITS(0,15) /*!< 16 bit capture/compare value of channel 0 */ + +/* TIMER_CH1CV */ +#define TIMER_CH1CV_CH1VAL BITS(0,15) /*!< 16 bit capture/compare value of channel 1 */ + +/* TIMER_CH2CV */ +#define TIMER_CH2CV_CH2VAL BITS(0,15) /*!< 16 bit capture/compare value of channel 2 */ + +/* TIMER_CH3CV */ +#define TIMER_CH3CV_CH3VAL BITS(0,15) /*!< 16 bit capture/compare value of channel 3 */ + +/* TIMER_CCHP */ +#define TIMER_CCHP_DTCFG BITS(0,7) /*!< dead time configure */ +#define TIMER_CCHP_PROT BITS(8,9) /*!< complementary register protect control */ +#define TIMER_CCHP_IOS BIT(10) /*!< idle mode off-state configure */ +#define TIMER_CCHP_ROS BIT(11) /*!< run mode off-state configure */ +#define TIMER_CCHP_BRKEN BIT(12) /*!< break enable */ +#define TIMER_CCHP_BRKP BIT(13) /*!< break polarity */ +#define TIMER_CCHP_OAEN BIT(14) /*!< output automatic enable */ +#define TIMER_CCHP_POEN BIT(15) /*!< primary output enable */ + +/* TIMER_DMACFG */ +#define TIMER_DMACFG_DMATA BITS(0,4) /*!< DMA transfer access start address */ +#define TIMER_DMACFG_DMATC BITS(8,12) /*!< DMA transfer count */ + +/* TIMER_DMATB */ +#define TIMER_DMATB_DMATB BITS(0,15) /*!< DMA transfer buffer address */ + +/* constants definitions */ +/* TIMER init parameter struct definitions */ +typedef struct +{ + uint16_t prescaler; /*!< prescaler value */ + uint16_t alignedmode; /*!< aligned mode */ + uint16_t counterdirection; /*!< counter direction */ + uint32_t period; /*!< period value */ + uint16_t clockdivision; /*!< clock division value */ + uint8_t repetitioncounter; /*!< the counter repetition value */ +}timer_parameter_struct; + +/* break parameter struct definitions */ +typedef struct +{ + uint16_t runoffstate; /*!< run mode off-state */ + uint16_t ideloffstate; /*!< idle mode off-state */ + uint16_t deadtime; /*!< dead time */ + uint16_t breakpolarity; /*!< break polarity */ + uint16_t outputautostate; /*!< output automatic enable */ + uint16_t protectmode; /*!< complementary register protect control */ + uint16_t breakstate; /*!< break enable */ +}timer_break_parameter_struct; + +/* channel output parameter struct definitions */ +typedef struct +{ + uint16_t outputstate; /*!< channel output state */ + uint16_t outputnstate; /*!< channel complementary output state */ + uint16_t ocpolarity; /*!< channel output polarity */ + uint16_t ocnpolarity; /*!< channel complementary output polarity */ + uint16_t ocidlestate; /*!< idle state of channel output */ + uint16_t ocnidlestate; /*!< idle state of channel complementary output */ +}timer_oc_parameter_struct; + +/* channel input parameter struct definitions */ +typedef struct +{ + uint16_t icpolarity; /*!< channel input polarity */ + uint16_t icselection; /*!< channel input mode selection */ + uint16_t icprescaler; /*!< channel input capture prescaler */ + uint16_t icfilter; /*!< channel input capture filter control */ +}timer_ic_parameter_struct; + +/* TIMER interrupt enable or disable */ +#define TIMER_INT_UP TIMER_DMAINTEN_UPIE /*!< update interrupt */ +#define TIMER_INT_CH0 TIMER_DMAINTEN_CH0IE /*!< channel 0 interrupt */ +#define TIMER_INT_CH1 TIMER_DMAINTEN_CH1IE /*!< channel 1 interrupt */ +#define TIMER_INT_CH2 TIMER_DMAINTEN_CH2IE /*!< channel 2 interrupt */ +#define TIMER_INT_CH3 TIMER_DMAINTEN_CH3IE /*!< channel 3 interrupt */ +#define TIMER_INT_CMT TIMER_DMAINTEN_CMTIE /*!< channel commutation interrupt flag */ +#define TIMER_INT_TRG TIMER_DMAINTEN_TRGIE /*!< trigger interrupt */ +#define TIMER_INT_BRK TIMER_DMAINTEN_BRKIE /*!< break interrupt */ + +/* TIMER interrupt flag */ +#define TIMER_INT_FLAG_UP TIMER_INT_UP /*!< update interrupt */ +#define TIMER_INT_FLAG_CH0 TIMER_INT_CH0 /*!< channel 0 interrupt */ +#define TIMER_INT_FLAG_CH1 TIMER_INT_CH1 /*!< channel 1 interrupt */ +#define TIMER_INT_FLAG_CH2 TIMER_INT_CH2 /*!< channel 2 interrupt */ +#define TIMER_INT_FLAG_CH3 TIMER_INT_CH3 /*!< channel 3 interrupt */ +#define TIMER_INT_FLAG_CMT TIMER_INT_CMT /*!< channel commutation interrupt flag */ +#define TIMER_INT_FLAG_TRG TIMER_INT_TRG /*!< trigger interrupt */ +#define TIMER_INT_FLAG_BRK TIMER_INT_BRK + +/* TIMER flag */ +#define TIMER_FLAG_UP TIMER_INTF_UPIF /*!< update flag */ +#define TIMER_FLAG_CH0 TIMER_INTF_CH0IF /*!< channel 0 flag */ +#define TIMER_FLAG_CH1 TIMER_INTF_CH1IF /*!< channel 1 flag */ +#define TIMER_FLAG_CH2 TIMER_INTF_CH2IF /*!< channel 2 flag */ +#define TIMER_FLAG_CH3 TIMER_INTF_CH3IF /*!< channel 3 flag */ +#define TIMER_FLAG_CMT TIMER_INTF_CMTIF /*!< channel control update flag */ +#define TIMER_FLAG_TRG TIMER_INTF_TRGIF /*!< trigger flag */ +#define TIMER_FLAG_BRK TIMER_INTF_BRKIF /*!< break flag */ +#define TIMER_FLAG_CH0O TIMER_INTF_CH0OF /*!< channel 0 overcapture flag */ +#define TIMER_FLAG_CH1O TIMER_INTF_CH1OF /*!< channel 1 overcapture flag */ +#define TIMER_FLAG_CH2O TIMER_INTF_CH2OF /*!< channel 2 overcapture flag */ +#define TIMER_FLAG_CH3O TIMER_INTF_CH3OF /*!< channel 3 overcapture flag */ + +/* TIMER DMA source enable */ +#define TIMER_DMA_UPD ((uint16_t)TIMER_DMAINTEN_UPDEN) /*!< update DMA enable */ +#define TIMER_DMA_CH0D ((uint16_t)TIMER_DMAINTEN_CH0DEN) /*!< channel 0 DMA enable */ +#define TIMER_DMA_CH1D ((uint16_t)TIMER_DMAINTEN_CH1DEN) /*!< channel 1 DMA enable */ +#define TIMER_DMA_CH2D ((uint16_t)TIMER_DMAINTEN_CH2DEN) /*!< channel 2 DMA enable */ +#define TIMER_DMA_CH3D ((uint16_t)TIMER_DMAINTEN_CH3DEN) /*!< channel 3 DMA enable */ +#define TIMER_DMA_CMTD ((uint16_t)TIMER_DMAINTEN_CMTDEN) /*!< commutation DMA request enable */ +#define TIMER_DMA_TRGD ((uint16_t)TIMER_DMAINTEN_TRGDEN) /*!< trigger DMA enable */ + +/* channel DMA request source selection */ +#define TIMER_DMAREQUEST_UPDATEEVENT TIMER_CTL1_DMAS /*!< DMA request of channel n is sent when update event occurs */ +#define TIMER_DMAREQUEST_CHANNELEVENT ((uint32_t)0x00000000U) /*!< DMA request of channel n is sent when channel n event occurs */ + +/* DMA access base address */ +#define DMACFG_DMATA(regval) (BITS(0, 4) & ((uint32_t)(regval) << 0U)) +#define TIMER_DMACFG_DMATA_CTL0 DMACFG_DMATA(0) /*!< DMA transfer address is TIMER_CTL0 */ +#define TIMER_DMACFG_DMATA_CTL1 DMACFG_DMATA(1) /*!< DMA transfer address is TIMER_CTL1 */ +#define TIMER_DMACFG_DMATA_SMCFG DMACFG_DMATA(2) /*!< DMA transfer address is TIMER_SMCFG */ +#define TIMER_DMACFG_DMATA_DMAINTEN DMACFG_DMATA(3) /*!< DMA transfer address is TIMER_DMAINTEN */ +#define TIMER_DMACFG_DMATA_INTF DMACFG_DMATA(4) /*!< DMA transfer address is TIMER_INTF */ +#define TIMER_DMACFG_DMATA_SWEVG DMACFG_DMATA(5) /*!< DMA transfer address is TIMER_SWEVG */ +#define TIMER_DMACFG_DMATA_CHCTL0 DMACFG_DMATA(6) /*!< DMA transfer address is TIMER_CHCTL0 */ +#define TIMER_DMACFG_DMATA_CHCTL1 DMACFG_DMATA(7) /*!< DMA transfer address is TIMER_CHCTL1 */ +#define TIMER_DMACFG_DMATA_CHCTL2 DMACFG_DMATA(8) /*!< DMA transfer address is TIMER_CHCTL2 */ +#define TIMER_DMACFG_DMATA_CNT DMACFG_DMATA(9) /*!< DMA transfer address is TIMER_CNT */ +#define TIMER_DMACFG_DMATA_PSC DMACFG_DMATA(10) /*!< DMA transfer address is TIMER_PSC */ +#define TIMER_DMACFG_DMATA_CAR DMACFG_DMATA(11) /*!< DMA transfer address is TIMER_CAR */ +#define TIMER_DMACFG_DMATA_CREP DMACFG_DMATA(12) /*!< DMA transfer address is TIMER_CREP */ +#define TIMER_DMACFG_DMATA_CH0CV DMACFG_DMATA(13) /*!< DMA transfer address is TIMER_CH0CV */ +#define TIMER_DMACFG_DMATA_CH1CV DMACFG_DMATA(14) /*!< DMA transfer address is TIMER_CH1CV */ +#define TIMER_DMACFG_DMATA_CH2CV DMACFG_DMATA(15) /*!< DMA transfer address is TIMER_CH2CV */ +#define TIMER_DMACFG_DMATA_CH3CV DMACFG_DMATA(16) /*!< DMA transfer address is TIMER_CH3CV */ +#define TIMER_DMACFG_DMATA_CCHP DMACFG_DMATA(17) /*!< DMA transfer address is TIMER_CCHP */ +#define TIMER_DMACFG_DMATA_DMACFG DMACFG_DMATA(18) /*!< DMA transfer address is TIMER_DMACFG */ + +/* DMA access burst length */ +#define DMACFG_DMATC(regval) (BITS(8, 12) & ((uint32_t)(regval) << 8U)) +#define TIMER_DMACFG_DMATC_1TRANSFER DMACFG_DMATC(0) /*!< DMA transfer 1 time */ +#define TIMER_DMACFG_DMATC_2TRANSFER DMACFG_DMATC(1) /*!< DMA transfer 2 times */ +#define TIMER_DMACFG_DMATC_3TRANSFER DMACFG_DMATC(2) /*!< DMA transfer 3 times */ +#define TIMER_DMACFG_DMATC_4TRANSFER DMACFG_DMATC(3) /*!< DMA transfer 4 times */ +#define TIMER_DMACFG_DMATC_5TRANSFER DMACFG_DMATC(4) /*!< DMA transfer 5 times */ +#define TIMER_DMACFG_DMATC_6TRANSFER DMACFG_DMATC(5) /*!< DMA transfer 6 times */ +#define TIMER_DMACFG_DMATC_7TRANSFER DMACFG_DMATC(6) /*!< DMA transfer 7 times */ +#define TIMER_DMACFG_DMATC_8TRANSFER DMACFG_DMATC(7) /*!< DMA transfer 8 times */ +#define TIMER_DMACFG_DMATC_9TRANSFER DMACFG_DMATC(8) /*!< DMA transfer 9 times */ +#define TIMER_DMACFG_DMATC_10TRANSFER DMACFG_DMATC(9) /*!< DMA transfer 10 times */ +#define TIMER_DMACFG_DMATC_11TRANSFER DMACFG_DMATC(10) /*!< DMA transfer 11 times */ +#define TIMER_DMACFG_DMATC_12TRANSFER DMACFG_DMATC(11) /*!< DMA transfer 12 times */ +#define TIMER_DMACFG_DMATC_13TRANSFER DMACFG_DMATC(12) /*!< DMA transfer 13 times */ +#define TIMER_DMACFG_DMATC_14TRANSFER DMACFG_DMATC(13) /*!< DMA transfer 14 times */ +#define TIMER_DMACFG_DMATC_15TRANSFER DMACFG_DMATC(14) /*!< DMA transfer 15 times */ +#define TIMER_DMACFG_DMATC_16TRANSFER DMACFG_DMATC(15) /*!< DMA transfer 16 times */ +#define TIMER_DMACFG_DMATC_17TRANSFER DMACFG_DMATC(16) /*!< DMA transfer 17 times */ +#define TIMER_DMACFG_DMATC_18TRANSFER DMACFG_DMATC(17) /*!< DMA transfer 18 times */ + +/* TIMER software event generation source */ +#define TIMER_EVENT_SRC_UPG ((uint16_t)0x0001U) /*!< update event generation */ +#define TIMER_EVENT_SRC_CH0G ((uint16_t)0x0002U) /*!< channel 0 capture or compare event generation */ +#define TIMER_EVENT_SRC_CH1G ((uint16_t)0x0004U) /*!< channel 1 capture or compare event generation */ +#define TIMER_EVENT_SRC_CH2G ((uint16_t)0x0008U) /*!< channel 2 capture or compare event generation */ +#define TIMER_EVENT_SRC_CH3G ((uint16_t)0x0010U) /*!< channel 3 capture or compare event generation */ +#define TIMER_EVENT_SRC_CMTG ((uint16_t)0x0020U) /*!< channel commutation event generation */ +#define TIMER_EVENT_SRC_TRGG ((uint16_t)0x0040U) /*!< trigger event generation */ +#define TIMER_EVENT_SRC_BRKG ((uint16_t)0x0080U) /*!< break event generation */ + +/* center-aligned mode selection */ +#define CTL0_CAM(regval) ((uint16_t)(BITS(5, 6) & ((uint32_t)(regval) << 5U))) +#define TIMER_COUNTER_EDGE CTL0_CAM(0) /*!< edge-aligned mode */ +#define TIMER_COUNTER_CENTER_DOWN CTL0_CAM(1) /*!< center-aligned and counting down assert mode */ +#define TIMER_COUNTER_CENTER_UP CTL0_CAM(2) /*!< center-aligned and counting up assert mode */ +#define TIMER_COUNTER_CENTER_BOTH CTL0_CAM(3) /*!< center-aligned and counting up/down assert mode */ + +/* TIMER prescaler reload mode */ +#define TIMER_PSC_RELOAD_NOW TIMER_SWEVG_UPG /*!< the prescaler is loaded right now */ +#define TIMER_PSC_RELOAD_UPDATE ((uint32_t)0x00000000U) /*!< the prescaler is loaded at the next update event */ + +/* count direction */ +#define TIMER_COUNTER_UP ((uint16_t)0x0000U) /*!< counter up direction */ +#define TIMER_COUNTER_DOWN ((uint16_t)TIMER_CTL0_DIR) /*!< counter down direction */ + +/* specify division ratio between TIMER clock and dead-time and sampling clock */ +#define CTL0_CKDIV(regval) ((uint16_t)(BITS(8, 9) & ((uint32_t)(regval) << 8U))) +#define TIMER_CKDIV_DIV1 CTL0_CKDIV(0) /*!< clock division value is 1,fDTS=fTIMER_CK */ +#define TIMER_CKDIV_DIV2 CTL0_CKDIV(1) /*!< clock division value is 2,fDTS= fTIMER_CK/2 */ +#define TIMER_CKDIV_DIV4 CTL0_CKDIV(2) /*!< clock division value is 4, fDTS= fTIMER_CK/4 */ + +/* single pulse mode */ +#define TIMER_SP_MODE_SINGLE TIMER_CTL0_SPM /*!< single pulse mode */ +#define TIMER_SP_MODE_REPETITIVE ((uint32_t)0x00000000U) /*!< repetitive pulse mode */ + +/* update source */ +#define TIMER_UPDATE_SRC_REGULAR TIMER_CTL0_UPS /*!< update generate only by counter overflow/underflow */ +#define TIMER_UPDATE_SRC_GLOBAL ((uint32_t)0x00000000U) /*!< update generate by setting of UPG bit or the counter overflow/underflow,or the slave mode controller trigger */ + +/* run mode off-state configure */ +#define TIMER_ROS_STATE_ENABLE ((uint16_t)TIMER_CCHP_ROS) /*!< when POEN bit is set, the channel output signals(CHx_O/CHx_ON) are enabled, with relationship to CHxEN/CHxNEN bits */ +#define TIMER_ROS_STATE_DISABLE ((uint16_t)0x0000U) /*!< when POEN bit is set, the channel output signals(CHx_O/CHx_ON) are disabled */ + + +/* idle mode off-state configure */ +#define TIMER_IOS_STATE_ENABLE ((uint16_t)TIMER_CCHP_IOS) /*!< when POEN bit is reset, he channel output signals(CHx_O/CHx_ON) are enabled, with relationship to CHxEN/CHxNEN bits */ +#define TIMER_IOS_STATE_DISABLE ((uint16_t)0x0000U) /*!< when POEN bit is reset, the channel output signals(CHx_O/CHx_ON) are disabled */ + +/* break input polarity */ +#define TIMER_BREAK_POLARITY_LOW ((uint16_t)0x0000U) /*!< break input polarity is low */ +#define TIMER_BREAK_POLARITY_HIGH ((uint16_t)TIMER_CCHP_BRKP) /*!< break input polarity is high */ + +/* output automatic enable */ +#define TIMER_OUTAUTO_ENABLE ((uint16_t)TIMER_CCHP_OAEN) /*!< output automatic enable */ +#define TIMER_OUTAUTO_DISABLE ((uint16_t)0x0000U) /*!< output automatic disable */ + +/* complementary register protect control */ +#define CCHP_PROT(regval) ((uint16_t)(BITS(8, 9) & ((uint32_t)(regval) << 8U))) +#define TIMER_CCHP_PROT_OFF CCHP_PROT(0) /*!< protect disable */ +#define TIMER_CCHP_PROT_0 CCHP_PROT(1) /*!< PROT mode 0 */ +#define TIMER_CCHP_PROT_1 CCHP_PROT(2) /*!< PROT mode 1 */ +#define TIMER_CCHP_PROT_2 CCHP_PROT(3) /*!< PROT mode 2 */ + +/* break input enable */ +#define TIMER_BREAK_ENABLE ((uint16_t)TIMER_CCHP_BRKEN) /*!< break input enable */ +#define TIMER_BREAK_DISABLE ((uint16_t)0x0000U) /*!< break input disable */ + +/* TIMER channel n(n=0,1,2,3) */ +#define TIMER_CH_0 ((uint16_t)0x0000U) /*!< TIMER channel 0(TIMERx(x=0..4)) */ +#define TIMER_CH_1 ((uint16_t)0x0001U) /*!< TIMER channel 1(TIMERx(x=0..4)) */ +#define TIMER_CH_2 ((uint16_t)0x0002U) /*!< TIMER channel 2(TIMERx(x=0..4)) */ +#define TIMER_CH_3 ((uint16_t)0x0003U) /*!< TIMER channel 3(TIMERx(x=0..4)) */ + +/* channel enable state */ +#define TIMER_CCX_ENABLE ((uint16_t)0x0001U) /*!< channel enable */ +#define TIMER_CCX_DISABLE ((uint16_t)0x0000U) /*!< channel disable */ + +/* channel complementary output enable state */ +#define TIMER_CCXN_ENABLE ((uint16_t)0x0004U) /*!< channel complementary enable */ +#define TIMER_CCXN_DISABLE ((uint16_t)0x0000U) /*!< channel complementary disable */ + +/* channel output polarity */ +#define TIMER_OC_POLARITY_HIGH ((uint16_t)0x0000U) /*!< channel output polarity is high */ +#define TIMER_OC_POLARITY_LOW ((uint16_t)0x0002U) /*!< channel output polarity is low */ + +/* channel complementary output polarity */ +#define TIMER_OCN_POLARITY_HIGH ((uint16_t)0x0000U) /*!< channel complementary output polarity is high */ +#define TIMER_OCN_POLARITY_LOW ((uint16_t)0x0008U) /*!< channel complementary output polarity is low */ + +/* idle state of channel output */ +#define TIMER_OC_IDLE_STATE_HIGH ((uint16_t)0x0100) /*!< idle state of channel output is high */ +#define TIMER_OC_IDLE_STATE_LOW ((uint16_t)0x0000) /*!< idle state of channel output is low */ + +/* idle state of channel complementary output */ +#define TIMER_OCN_IDLE_STATE_HIGH ((uint16_t)0x0200U) /*!< idle state of channel complementary output is high */ +#define TIMER_OCN_IDLE_STATE_LOW ((uint16_t)0x0000U) /*!< idle state of channel complementary output is low */ + +/* channel output compare mode */ +#define TIMER_OC_MODE_TIMING ((uint16_t)0x0000U) /*!< timing mode */ +#define TIMER_OC_MODE_ACTIVE ((uint16_t)0x0010U) /*!< active mode */ +#define TIMER_OC_MODE_INACTIVE ((uint16_t)0x0020U) /*!< inactive mode */ +#define TIMER_OC_MODE_TOGGLE ((uint16_t)0x0030U) /*!< toggle mode */ +#define TIMER_OC_MODE_LOW ((uint16_t)0x0040U) /*!< force low mode */ +#define TIMER_OC_MODE_HIGH ((uint16_t)0x0050U) /*!< force high mode */ +#define TIMER_OC_MODE_PWM0 ((uint16_t)0x0060U) /*!< PWM0 mode */ +#define TIMER_OC_MODE_PWM1 ((uint16_t)0x0070U) /*!< PWM1 mode */ + +/* channel output compare shadow enable */ +#define TIMER_OC_SHADOW_ENABLE ((uint16_t)0x0008U) /*!< channel output shadow state enable */ +#define TIMER_OC_SHADOW_DISABLE ((uint16_t)0x0000U) /*!< channel output shadow state disable */ + +/* channel output compare fast enable */ +#define TIMER_OC_FAST_ENABLE ((uint16_t)0x0004) /*!< channel output fast function enable */ +#define TIMER_OC_FAST_DISABLE ((uint16_t)0x0000) /*!< channel output fast function disable */ + +/* channel output compare clear enable */ +#define TIMER_OC_CLEAR_ENABLE ((uint16_t)0x0080U) /*!< channel output clear function enable */ +#define TIMER_OC_CLEAR_DISABLE ((uint16_t)0x0000U) /*!< channel output clear function disable */ + +/* channel control shadow register update control */ +#define TIMER_UPDATECTL_CCU ((uint32_t)0x00000000U) /*!< the shadow registers update by when CMTG bit is set */ +#define TIMER_UPDATECTL_CCUTRI TIMER_CTL1_CCUC /*!< the shadow registers update by when CMTG bit is set or an rising edge of TRGI occurs */ + +/* channel input capture polarity */ +#define TIMER_IC_POLARITY_RISING ((uint16_t)0x0000U) /*!< input capture rising edge */ +#define TIMER_IC_POLARITY_FALLING ((uint16_t)0x0002U) /*!< input capture falling edge */ +#define TIMER_IC_POLARITY_BOTH_EDGE ((uint16_t)0x000AU) /*!< input capture both edge */ + +/* TIMER input capture selection */ +#define TIMER_IC_SELECTION_DIRECTTI ((uint16_t)0x0001U) /*!< channel n is configured as input and icy is mapped on CIy */ +#define TIMER_IC_SELECTION_INDIRECTTI ((uint16_t)0x0002U) /*!< channel n is configured as input and icy is mapped on opposite input */ +#define TIMER_IC_SELECTION_ITS ((uint16_t)0x0003U) /*!< channel n is configured as input and icy is mapped on ITS */ + +/* channel input capture prescaler */ +#define TIMER_IC_PSC_DIV1 ((uint16_t)0x0000U) /*!< no prescaler */ +#define TIMER_IC_PSC_DIV2 ((uint16_t)0x0004U) /*!< divided by 2 */ +#define TIMER_IC_PSC_DIV4 ((uint16_t)0x0008U) /*!< divided by 4 */ +#define TIMER_IC_PSC_DIV8 ((uint16_t)0x000CU) /*!< divided by 8 */ + +/* trigger selection */ +#define SMCFG_TRGSEL(regval) (BITS(4, 6) & ((uint32_t)(regval) << 4U)) +#define TIMER_SMCFG_TRGSEL_ITI0 SMCFG_TRGSEL(0) /*!< internal trigger 0 */ +#define TIMER_SMCFG_TRGSEL_ITI1 SMCFG_TRGSEL(1) /*!< internal trigger 1 */ +#define TIMER_SMCFG_TRGSEL_ITI2 SMCFG_TRGSEL(2) /*!< internal trigger 2 */ +#define TIMER_SMCFG_TRGSEL_ITI3 SMCFG_TRGSEL(3) /*!< internal trigger 3 */ +#define TIMER_SMCFG_TRGSEL_CI0F_ED SMCFG_TRGSEL(4) /*!< TI0 Edge Detector */ +#define TIMER_SMCFG_TRGSEL_CI0FE0 SMCFG_TRGSEL(5) /*!< filtered TIMER input 0 */ +#define TIMER_SMCFG_TRGSEL_CI1FE1 SMCFG_TRGSEL(6) /*!< filtered TIMER input 1 */ +#define TIMER_SMCFG_TRGSEL_ETIFP SMCFG_TRGSEL(7) /*!< filtered external trigger input */ + +/* master mode control */ +#define CTL1_MMC(regval) (BITS(4, 6) & ((uint32_t)(regval) << 4U)) +#define TIMER_TRI_OUT_SRC_RESET CTL1_MMC(0) /*!< the UPG bit as trigger output */ +#define TIMER_TRI_OUT_SRC_ENABLE CTL1_MMC(1) /*!< the counter enable signal TIMER_CTL0_CEN as trigger output */ +#define TIMER_TRI_OUT_SRC_UPDATE CTL1_MMC(2) /*!< update event as trigger output */ +#define TIMER_TRI_OUT_SRC_CH0 CTL1_MMC(3) /*!< a capture or a compare match occurred in channel 0 as trigger output TRGO */ +#define TIMER_TRI_OUT_SRC_O0CPRE CTL1_MMC(4) /*!< O0CPRE as trigger output */ +#define TIMER_TRI_OUT_SRC_O1CPRE CTL1_MMC(5) /*!< O1CPRE as trigger output */ +#define TIMER_TRI_OUT_SRC_O2CPRE CTL1_MMC(6) /*!< O2CPRE as trigger output */ +#define TIMER_TRI_OUT_SRC_O3CPRE CTL1_MMC(7) /*!< O3CPRE as trigger output */ + +/* slave mode control */ +#define SMCFG_SMC(regval) (BITS(0, 2) & ((uint32_t)(regval) << 0U)) +#define TIMER_SLAVE_MODE_DISABLE SMCFG_SMC(0) /*!< slave mode disable */ +#define TIMER_ENCODER_MODE0 SMCFG_SMC(1) /*!< encoder mode 0 */ +#define TIMER_ENCODER_MODE1 SMCFG_SMC(2) /*!< encoder mode 1 */ +#define TIMER_ENCODER_MODE2 SMCFG_SMC(3) /*!< encoder mode 2 */ +#define TIMER_SLAVE_MODE_RESTART SMCFG_SMC(4) /*!< restart mode */ +#define TIMER_SLAVE_MODE_PAUSE SMCFG_SMC(5) /*!< pause mode */ +#define TIMER_SLAVE_MODE_EVENT SMCFG_SMC(6) /*!< event mode */ +#define TIMER_SLAVE_MODE_EXTERNAL0 SMCFG_SMC(7) /*!< external clock mode 0 */ + +/* master slave mode selection */ +#define TIMER_MASTER_SLAVE_MODE_ENABLE TIMER_SMCFG_MSM /*!< master slave mode enable */ +#define TIMER_MASTER_SLAVE_MODE_DISABLE ((uint32_t)0x00000000U) /*!< master slave mode disable */ + +/* external trigger prescaler */ +#define SMCFG_ETPSC(regval) (BITS(12, 13) & ((uint32_t)(regval) << 12U)) +#define TIMER_EXT_TRI_PSC_OFF SMCFG_ETPSC(0) /*!< no divided */ +#define TIMER_EXT_TRI_PSC_DIV2 SMCFG_ETPSC(1) /*!< divided by 2 */ +#define TIMER_EXT_TRI_PSC_DIV4 SMCFG_ETPSC(2) /*!< divided by 4 */ +#define TIMER_EXT_TRI_PSC_DIV8 SMCFG_ETPSC(3) /*!< divided by 8 */ + +/* external trigger polarity */ +#define TIMER_ETP_FALLING TIMER_SMCFG_ETP /*!< active low or falling edge active */ +#define TIMER_ETP_RISING ((uint32_t)0x00000000U) /*!< active high or rising edge active */ + +/* channel 0 trigger input selection */ +#define TIMER_HALLINTERFACE_ENABLE TIMER_CTL1_TI0S /*!< TIMER hall sensor mode enable */ +#define TIMER_HALLINTERFACE_DISABLE ((uint32_t)0x00000000U) /*!< TIMER hall sensor mode disable */ + +/* TIMERx(x=0..4) write CHxVAL register selection */ +#define TIMER_CHVSEL_ENABLE ((uint16_t)TIMER_CFG_OUTSEL) /*!< write CHxVAL register selection enable */ +#define TIMER_CHVSEL_DISABLE ((uint16_t)0x0000U) /*!< write CHxVAL register selection disable */ + +/* function declarations */ +/* TIMER timebase */ +/* deinit a timer */ +void timer_deinit(uint32_t timer_periph); +/* initialize TIMER init parameter struct */ +void timer_struct_para_init(timer_parameter_struct* initpara); +/* initialize TIMER counter */ +void timer_init(uint32_t timer_periph, timer_parameter_struct* initpara); +/* enable a timer */ +void timer_enable(uint32_t timer_periph); +/* disable a timer */ +void timer_disable(uint32_t timer_periph); +/* enable the auto reload shadow function */ +void timer_auto_reload_shadow_enable(uint32_t timer_periph); +/* disable the auto reload shadow function */ +void timer_auto_reload_shadow_disable(uint32_t timer_periph); +/* enable the update event */ +void timer_update_event_enable(uint32_t timer_periph); +/* disable the update event */ +void timer_update_event_disable(uint32_t timer_periph); +/* set TIMER counter alignment mode */ +void timer_counter_alignment(uint32_t timer_periph, uint16_t aligned); +/* set TIMER counter up direction */ +void timer_counter_up_direction(uint32_t timer_periph); +/* set TIMER counter down direction */ +void timer_counter_down_direction(uint32_t timer_periph); + +/* configure TIMER prescaler */ +void timer_prescaler_config(uint32_t timer_periph, uint16_t prescaler, uint32_t pscreload); +/* configure TIMER repetition register value */ +void timer_repetition_value_config(uint32_t timer_periph, uint16_t repetition); +/* configure TIMER autoreload register value */ +void timer_autoreload_value_config(uint32_t timer_periph, uint16_t autoreload); +/* configure TIMER counter register value */ +void timer_counter_value_config(uint32_t timer_periph, uint16_t counter); +/* read TIMER counter value */ +uint32_t timer_counter_read(uint32_t timer_periph); +/* read TIMER prescaler value */ +uint16_t timer_prescaler_read(uint32_t timer_periph); +/* configure TIMER single pulse mode */ +void timer_single_pulse_mode_config(uint32_t timer_periph, uint32_t spmode); +/* configure TIMER update source */ +void timer_update_source_config(uint32_t timer_periph, uint32_t update); + +/* TIMER DMA and event */ +/* enable the TIMER DMA */ +void timer_dma_enable(uint32_t timer_periph, uint16_t dma); +/* disable the TIMER DMA */ +void timer_dma_disable(uint32_t timer_periph, uint16_t dma); +/* channel DMA request source selection */ +void timer_channel_dma_request_source_select(uint32_t timer_periph, uint32_t dma_request); +/* configure the TIMER DMA transfer */ +void timer_dma_transfer_config(uint32_t timer_periph, uint32_t dma_baseaddr, uint32_t dma_lenth); +/* software generate events */ +void timer_event_software_generate(uint32_t timer_periph, uint16_t event); + +/* TIMER channel complementary protection */ +/* initialize TIMER break parameter struct */ +void timer_break_struct_para_init(timer_break_parameter_struct* breakpara); +/* configure TIMER break function */ +void timer_break_config(uint32_t timer_periph, timer_break_parameter_struct* breakpara); +/* enable TIMER break function */ +void timer_break_enable(uint32_t timer_periph); +/* disable TIMER break function */ +void timer_break_disable(uint32_t timer_periph); +/* enable TIMER output automatic function */ +void timer_automatic_output_enable(uint32_t timer_periph); +/* disable TIMER output automatic function */ +void timer_automatic_output_disable(uint32_t timer_periph); +/* enable or disable TIMER primary output function */ +void timer_primary_output_config(uint32_t timer_periph, ControlStatus newvalue); +/* enable or disable channel capture/compare control shadow register */ +void timer_channel_control_shadow_config(uint32_t timer_periph, ControlStatus newvalue); +/* configure TIMER channel control shadow register update control */ +void timer_channel_control_shadow_update_config(uint32_t timer_periph, uint32_t ccuctl); + +/* TIMER channel output */ +/* initialize TIMER channel output parameter struct */ +void timer_channel_output_struct_para_init(timer_oc_parameter_struct* ocpara); +/* configure TIMER channel output function */ +void timer_channel_output_config(uint32_t timer_periph, uint16_t channel, timer_oc_parameter_struct* ocpara); +/* configure TIMER channel output compare mode */ +void timer_channel_output_mode_config(uint32_t timer_periph, uint16_t channel, uint16_t ocmode); +/* configure TIMER channel output pulse value */ +void timer_channel_output_pulse_value_config(uint32_t timer_periph, uint16_t channel, uint32_t pulse); +/* configure TIMER channel output shadow function */ +void timer_channel_output_shadow_config(uint32_t timer_periph, uint16_t channel, uint16_t ocshadow); +/* configure TIMER channel output fast function */ +void timer_channel_output_fast_config(uint32_t timer_periph, uint16_t channel, uint16_t ocfast); +/* configure TIMER channel output clear function */ +void timer_channel_output_clear_config(uint32_t timer_periph, uint16_t channel, uint16_t occlear); +/* configure TIMER channel output polarity */ +void timer_channel_output_polarity_config(uint32_t timer_periph, uint16_t channel, uint16_t ocpolarity); +/* configure TIMER channel complementary output polarity */ +void timer_channel_complementary_output_polarity_config(uint32_t timer_periph, uint16_t channel, uint16_t ocnpolarity); +/* configure TIMER channel enable state */ +void timer_channel_output_state_config(uint32_t timer_periph, uint16_t channel, uint32_t state); +/* configure TIMER channel complementary output enable state */ +void timer_channel_complementary_output_state_config(uint32_t timer_periph, uint16_t channel, uint16_t ocnstate); + +/* TIMER channel input */ +/* initialize TIMER channel input parameter struct */ +void timer_channel_input_struct_para_init(timer_ic_parameter_struct* icpara); +/* configure TIMER input capture parameter */ +void timer_input_capture_config(uint32_t timer_periph, uint16_t channel, timer_ic_parameter_struct* icpara); +/* configure TIMER channel input capture prescaler value */ +void timer_channel_input_capture_prescaler_config(uint32_t timer_periph, uint16_t channel, uint16_t prescaler); +/* read TIMER channel capture compare register value */ +uint32_t timer_channel_capture_value_register_read(uint32_t timer_periph, uint16_t channel); +/* configure TIMER input pwm capture function */ +void timer_input_pwm_capture_config(uint32_t timer_periph, uint16_t channel, timer_ic_parameter_struct* icpwm); +/* configure TIMER hall sensor mode */ +void timer_hall_mode_config(uint32_t timer_periph, uint32_t hallmode); + +/* TIMER master and slave mode */ +/* select TIMER input trigger source */ +void timer_input_trigger_source_select(uint32_t timer_periph, uint32_t intrigger); +/* select TIMER master mode output trigger source */ +void timer_master_output_trigger_source_select(uint32_t timer_periph, uint32_t outrigger); +/* select TIMER slave mode */ +void timer_slave_mode_select(uint32_t timer_periph, uint32_t slavemode); +/* configure TIMER master slave mode */ +void timer_master_slave_mode_config(uint32_t timer_periph, uint32_t masterslave); +/* configure TIMER external trigger input */ +void timer_external_trigger_config(uint32_t timer_periph, uint32_t extprescaler, uint32_t extpolarity, uint32_t extfilter); +/* configure TIMER quadrature decoder mode */ +void timer_quadrature_decoder_mode_config(uint32_t timer_periph, uint32_t decomode, uint16_t ic0polarity, uint16_t ic1polarity); +/* configure TIMER internal clock mode */ +void timer_internal_clock_config(uint32_t timer_periph); +/* configure TIMER the internal trigger as external clock input */ +void timer_internal_trigger_as_external_clock_config(uint32_t timer_periph, uint32_t intrigger); +/* configure TIMER the external trigger as external clock input */ +void timer_external_trigger_as_external_clock_config(uint32_t timer_periph, uint32_t extrigger, uint16_t extpolarity, uint32_t extfilter); +/* configure TIMER the external clock mode 0 */ +void timer_external_clock_mode0_config(uint32_t timer_periph, uint32_t extprescaler, uint32_t extpolarity, uint32_t extfilter); +/* configure TIMER the external clock mode 1 */ +void timer_external_clock_mode1_config(uint32_t timer_periph, uint32_t extprescaler, uint32_t extpolarity, uint32_t extfilter); +/* disable TIMER the external clock mode 1 */ +void timer_external_clock_mode1_disable(uint32_t timer_periph); + +/* TIMER interrupt and flag */ +/* enable the TIMER interrupt */ +void timer_interrupt_enable(uint32_t timer_periph, uint32_t interrupt); +/* disable the TIMER interrupt */ +void timer_interrupt_disable(uint32_t timer_periph, uint32_t interrupt); +/* get TIMER interrupt flag */ +FlagStatus timer_interrupt_flag_get(uint32_t timer_periph, uint32_t interrupt); +/* clear TIMER interrupt flag */ +void timer_interrupt_flag_clear(uint32_t timer_periph, uint32_t interrupt); +/* get TIMER flag */ +FlagStatus timer_flag_get(uint32_t timer_periph, uint32_t flag); +/* clear TIMER flag */ +void timer_flag_clear(uint32_t timer_periph, uint32_t flag); + +#endif /* GD32VF103_TIMER_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_usart.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_usart.h new file mode 100644 index 00000000..dfa59cf5 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_usart.h @@ -0,0 +1,378 @@ +/*! + \file gd32vf103_usart.h + \brief definitions for the USART + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2018, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_USART_H +#define GD32VF103_USART_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* USARTx(x=0,1,2)/UARTx(x=3,4) definitions */ +#define USART1 USART_BASE /*!< USART1 base address */ +#define USART2 (USART_BASE+(0x00000400U)) /*!< USART2 base address */ +#define UART3 (USART_BASE+(0x00000800U)) /*!< UART3 base address */ +#define UART4 (USART_BASE+(0x00000C00U)) /*!< UART4 base address */ +#define USART0 (USART_BASE+(0x0000F400U)) /*!< USART0 base address */ + +/* registers definitions */ +#define USART_STAT(usartx) REG32((usartx) + (0x00000000U)) /*!< USART status register */ +#define USART_DATA(usartx) REG32((usartx) + (0x00000004U)) /*!< USART data register */ +#define USART_BAUD(usartx) REG32((usartx) + (0x00000008U)) /*!< USART baud rate register */ +#define USART_CTL0(usartx) REG32((usartx) + (0x0000000CU)) /*!< USART control register 0 */ +#define USART_CTL1(usartx) REG32((usartx) + (0x00000010U)) /*!< USART control register 1 */ +#define USART_CTL2(usartx) REG32((usartx) + (0x00000014U)) /*!< USART control register 2 */ +#define USART_GP(usartx) REG32((usartx) + (0x00000018U)) /*!< USART guard time and prescaler register */ + +/* bits definitions */ +/* USARTx_STAT */ +#define USART_STAT_PERR BIT(0) /*!< parity error flag */ +#define USART_STAT_FERR BIT(1) /*!< frame error flag */ +#define USART_STAT_NERR BIT(2) /*!< noise error flag */ +#define USART_STAT_ORERR BIT(3) /*!< overrun error */ +#define USART_STAT_IDLEF BIT(4) /*!< IDLE frame detected flag */ +#define USART_STAT_RBNE BIT(5) /*!< read data buffer not empty */ +#define USART_STAT_TC BIT(6) /*!< transmission complete */ +#define USART_STAT_TBE BIT(7) /*!< transmit data buffer empty */ +#define USART_STAT_LBDF BIT(8) /*!< LIN break detected flag */ +#define USART_STAT_CTSF BIT(9) /*!< CTS change flag */ + +/* USARTx_DATA */ +#define USART_DATA_DATA BITS(0,8) /*!< transmit or read data value */ + +/* USARTx_BAUD */ +#define USART_BAUD_FRADIV BITS(0,3) /*!< fraction part of baud-rate divider */ +#define USART_BAUD_INTDIV BITS(4,15) /*!< integer part of baud-rate divider */ + +/* USARTx_CTL0 */ +#define USART_CTL0_SBKCMD BIT(0) /*!< send break command */ +#define USART_CTL0_RWU BIT(1) /*!< receiver wakeup from mute mode */ +#define USART_CTL0_REN BIT(2) /*!< receiver enable */ +#define USART_CTL0_TEN BIT(3) /*!< transmitter enable */ +#define USART_CTL0_IDLEIE BIT(4) /*!< idle line detected interrupt enable */ +#define USART_CTL0_RBNEIE BIT(5) /*!< read data buffer not empty interrupt and overrun error interrupt enable */ +#define USART_CTL0_TCIE BIT(6) /*!< transmission complete interrupt enable */ +#define USART_CTL0_TBEIE BIT(7) /*!< transmitter buffer empty interrupt enable */ +#define USART_CTL0_PERRIE BIT(8) /*!< parity error interrupt enable */ +#define USART_CTL0_PM BIT(9) /*!< parity mode */ +#define USART_CTL0_PCEN BIT(10) /*!< parity check function enable */ +#define USART_CTL0_WM BIT(11) /*!< wakeup method in mute mode */ +#define USART_CTL0_WL BIT(12) /*!< word length */ +#define USART_CTL0_UEN BIT(13) /*!< USART enable */ + +/* USARTx_CTL1 */ +#define USART_CTL1_ADDR BITS(0,3) /*!< address of USART */ +#define USART_CTL1_LBLEN BIT(5) /*!< LIN break frame length */ +#define USART_CTL1_LBDIE BIT(6) /*!< LIN break detected interrupt eanble */ +#define USART_CTL1_CLEN BIT(8) /*!< CK length */ +#define USART_CTL1_CPH BIT(9) /*!< CK phase */ +#define USART_CTL1_CPL BIT(10) /*!< CK polarity */ +#define USART_CTL1_CKEN BIT(11) /*!< CK pin enable */ +#define USART_CTL1_STB BITS(12,13) /*!< STOP bits length */ +#define USART_CTL1_LMEN BIT(14) /*!< LIN mode enable */ + +/* USARTx_CTL2 */ +#define USART_CTL2_ERRIE BIT(0) /*!< error interrupt enable */ +#define USART_CTL2_IREN BIT(1) /*!< IrDA mode enable */ +#define USART_CTL2_IRLP BIT(2) /*!< IrDA low-power */ +#define USART_CTL2_HDEN BIT(3) /*!< half-duplex enable */ +#define USART_CTL2_NKEN BIT(4) /*!< NACK enable in smartcard mode */ +#define USART_CTL2_SCEN BIT(5) /*!< smartcard mode enable */ +#define USART_CTL2_DENR BIT(6) /*!< DMA request enable for reception */ +#define USART_CTL2_DENT BIT(7) /*!< DMA request enable for transmission */ +#define USART_CTL2_RTSEN BIT(8) /*!< RTS enable */ +#define USART_CTL2_CTSEN BIT(9) /*!< CTS enable */ +#define USART_CTL2_CTSIE BIT(10) /*!< CTS interrupt enable */ + +/* USARTx_GP */ +#define USART_GP_PSC BITS(0,7) /*!< prescaler value for dividing the system clock */ +#define USART_GP_GUAT BITS(8,15) /*!< guard time value in smartcard mode */ + +/* constants definitions */ +/* define the USART bit position and its register index offset */ +#define USART_REGIDX_BIT(regidx, bitpos) (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos)) +#define USART_REG_VAL(usartx, offset) (REG32((usartx) + (((uint32_t)(offset) & (0x0000FFFFU)) >> 6))) +#define USART_BIT_POS(val) ((uint32_t)(val) & (0x0000001FU)) +#define USART_REGIDX_BIT2(regidx, bitpos, regidx2, bitpos2) (((uint32_t)(regidx2) << 22) | (uint32_t)((bitpos2) << 16)\ + | (((uint32_t)(regidx) << 6) | (uint32_t)(bitpos))) +#define USART_REG_VAL2(usartx, offset) (REG32((usartx) + ((uint32_t)(offset) >> 22))) +#define USART_BIT_POS2(val) (((uint32_t)(val) & (0x001F0000U)) >> 16) + +/* register offset */ +#define USART_STAT_REG_OFFSET (0x00000000U) /*!< STAT register offset */ +#define USART_CTL0_REG_OFFSET (0x0000000CU) /*!< CTL0 register offset */ +#define USART_CTL1_REG_OFFSET (0x00000010U) /*!< CTL1 register offset */ +#define USART_CTL2_REG_OFFSET (0x00000014U) /*!< CTL2 register offset */ + +/* USART flags */ +typedef enum +{ + /* flags in STAT register */ + USART_FLAG_CTSF = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 9U), /*!< CTS change flag */ + USART_FLAG_LBDF = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 8U), /*!< LIN break detected flag */ + USART_FLAG_TBE = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 7U), /*!< transmit data buffer empty */ + USART_FLAG_TC = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 6U), /*!< transmission complete */ + USART_FLAG_RBNE = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 5U), /*!< read data buffer not empty */ + USART_FLAG_IDLEF = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 4U), /*!< IDLE frame detected flag */ + USART_FLAG_ORERR = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 3U), /*!< overrun error */ + USART_FLAG_NERR = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 2U), /*!< noise error flag */ + USART_FLAG_FERR = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 1U), /*!< frame error flag */ + USART_FLAG_PERR = USART_REGIDX_BIT(USART_STAT_REG_OFFSET, 0U), /*!< parity error flag */ +}usart_flag_enum; + +/* USART interrupt flags */ +typedef enum +{ + /* interrupt flags in CTL0 register */ + USART_INT_FLAG_PERR = USART_REGIDX_BIT2(USART_CTL0_REG_OFFSET, 8U, USART_STAT_REG_OFFSET, 0U), /*!< parity error interrupt and flag */ + USART_INT_FLAG_TBE = USART_REGIDX_BIT2(USART_CTL0_REG_OFFSET, 7U, USART_STAT_REG_OFFSET, 7U), /*!< transmitter buffer empty interrupt and flag */ + USART_INT_FLAG_TC = USART_REGIDX_BIT2(USART_CTL0_REG_OFFSET, 6U, USART_STAT_REG_OFFSET, 6U), /*!< transmission complete interrupt and flag */ + USART_INT_FLAG_RBNE = USART_REGIDX_BIT2(USART_CTL0_REG_OFFSET, 5U, USART_STAT_REG_OFFSET, 5U), /*!< read data buffer not empty interrupt and flag */ + USART_INT_FLAG_RBNE_ORERR = USART_REGIDX_BIT2(USART_CTL0_REG_OFFSET, 5U, USART_STAT_REG_OFFSET, 3U), /*!< read data buffer not empty interrupt and overrun error flag */ + USART_INT_FLAG_IDLE = USART_REGIDX_BIT2(USART_CTL0_REG_OFFSET, 4U, USART_STAT_REG_OFFSET, 4U), /*!< IDLE line detected interrupt and flag */ + /* interrupt flags in CTL1 register */ + USART_INT_FLAG_LBD = USART_REGIDX_BIT2(USART_CTL1_REG_OFFSET, 6U, USART_STAT_REG_OFFSET, 8U), /*!< LIN break detected interrupt and flag */ + /* interrupt flags in CTL2 register */ + USART_INT_FLAG_CTS = USART_REGIDX_BIT2(USART_CTL2_REG_OFFSET, 10U, USART_STAT_REG_OFFSET, 9U), /*!< CTS interrupt and flag */ + USART_INT_FLAG_ERR_ORERR = USART_REGIDX_BIT2(USART_CTL2_REG_OFFSET, 0U, USART_STAT_REG_OFFSET, 3U), /*!< error interrupt and overrun error */ + USART_INT_FLAG_ERR_NERR = USART_REGIDX_BIT2(USART_CTL2_REG_OFFSET, 0U, USART_STAT_REG_OFFSET, 2U), /*!< error interrupt and noise error flag */ + USART_INT_FLAG_ERR_FERR = USART_REGIDX_BIT2(USART_CTL2_REG_OFFSET, 0U, USART_STAT_REG_OFFSET, 1U), /*!< error interrupt and frame error flag */ +}usart_interrupt_flag_enum; + +/* USART interrupt enable or disable */ +typedef enum +{ + /* interrupt in CTL0 register */ + USART_INT_PERR = USART_REGIDX_BIT(USART_CTL0_REG_OFFSET, 8U), /*!< parity error interrupt */ + USART_INT_TBE = USART_REGIDX_BIT(USART_CTL0_REG_OFFSET, 7U), /*!< transmitter buffer empty interrupt */ + USART_INT_TC = USART_REGIDX_BIT(USART_CTL0_REG_OFFSET, 6U), /*!< transmission complete interrupt */ + USART_INT_RBNE = USART_REGIDX_BIT(USART_CTL0_REG_OFFSET, 5U), /*!< read data buffer not empty interrupt and overrun error interrupt */ + USART_INT_IDLE = USART_REGIDX_BIT(USART_CTL0_REG_OFFSET, 4U), /*!< IDLE line detected interrupt */ + /* interrupt in CTL1 register */ + USART_INT_LBD = USART_REGIDX_BIT(USART_CTL1_REG_OFFSET, 6U), /*!< LIN break detected interrupt */ + /* interrupt in CTL2 register */ + USART_INT_CTS = USART_REGIDX_BIT(USART_CTL2_REG_OFFSET, 10U), /*!< CTS interrupt */ + USART_INT_ERR = USART_REGIDX_BIT(USART_CTL2_REG_OFFSET, 0U), /*!< error interrupt */ +}usart_interrupt_enum; + +/* USART receiver configure */ +#define CTL0_REN(regval) (BIT(2) & ((uint32_t)(regval) << 2)) +#define USART_RECEIVE_ENABLE CTL0_REN(1) /*!< enable receiver */ +#define USART_RECEIVE_DISABLE CTL0_REN(0) /*!< disable receiver */ + +/* USART transmitter configure */ +#define CTL0_TEN(regval) (BIT(3) & ((uint32_t)(regval) << 3)) +#define USART_TRANSMIT_ENABLE CTL0_TEN(1) /*!< enable transmitter */ +#define USART_TRANSMIT_DISABLE CTL0_TEN(0) /*!< disable transmitter */ + +/* USART parity bits definitions */ +#define CTL0_PM(regval) (BITS(9,10) & ((uint32_t)(regval) << 9)) +#define USART_PM_NONE CTL0_PM(0) /*!< no parity */ +#define USART_PM_EVEN CTL0_PM(2) /*!< even parity */ +#define USART_PM_ODD CTL0_PM(3) /*!< odd parity */ + +/* USART wakeup method in mute mode */ +#define CTL0_WM(regval) (BIT(11) & ((uint32_t)(regval) << 11)) +#define USART_WM_IDLE CTL0_WM(0) /*!< idle line */ +#define USART_WM_ADDR CTL0_WM(1) /*!< address match */ + +/* USART word length definitions */ +#define CTL0_WL(regval) (BIT(12) & ((uint32_t)(regval) << 12)) +#define USART_WL_8BIT CTL0_WL(0) /*!< 8 bits */ +#define USART_WL_9BIT CTL0_WL(1) /*!< 9 bits */ + +/* USART stop bits definitions */ +#define CTL1_STB(regval) (BITS(12,13) & ((uint32_t)(regval) << 12)) +#define USART_STB_1BIT CTL1_STB(0) /*!< 1 bit */ +#define USART_STB_0_5BIT CTL1_STB(1) /*!< 0.5 bit */ +#define USART_STB_2BIT CTL1_STB(2) /*!< 2 bits */ +#define USART_STB_1_5BIT CTL1_STB(3) /*!< 1.5 bits */ + +/* USART LIN break frame length */ +#define CTL1_LBLEN(regval) (BIT(5) & ((uint32_t)(regval) << 5)) +#define USART_LBLEN_10B CTL1_LBLEN(0) /*!< 10 bits */ +#define USART_LBLEN_11B CTL1_LBLEN(1) /*!< 11 bits */ + +/* USART CK length */ +#define CTL1_CLEN(regval) (BIT(8) & ((uint32_t)(regval) << 8)) +#define USART_CLEN_NONE CTL1_CLEN(0) /*!< there are 7 CK pulses for an 8 bit frame and 8 CK pulses for a 9 bit frame */ +#define USART_CLEN_EN CTL1_CLEN(1) /*!< there are 8 CK pulses for an 8 bit frame and 9 CK pulses for a 9 bit frame */ + +/* USART clock phase */ +#define CTL1_CPH(regval) (BIT(9) & ((uint32_t)(regval) << 9)) +#define USART_CPH_1CK CTL1_CPH(0) /*!< first clock transition is the first data capture edge */ +#define USART_CPH_2CK CTL1_CPH(1) /*!< second clock transition is the first data capture edge */ + +/* USART clock polarity */ +#define CTL1_CPL(regval) (BIT(10) & ((uint32_t)(regval) << 10)) +#define USART_CPL_LOW CTL1_CPL(0) /*!< steady low value on CK pin */ +#define USART_CPL_HIGH CTL1_CPL(1) /*!< steady high value on CK pin */ + +/* USART DMA request for receive configure */ +#define CLT2_DENR(regval) (BIT(6) & ((uint32_t)(regval) << 6)) +#define USART_DENR_ENABLE CLT2_DENR(1) /*!< DMA request enable for reception */ +#define USART_DENR_DISABLE CLT2_DENR(0) /*!< DMA request disable for reception */ + +/* USART DMA request for transmission configure */ +#define CLT2_DENT(regval) (BIT(7) & ((uint32_t)(regval) << 7)) +#define USART_DENT_ENABLE CLT2_DENT(1) /*!< DMA request enable for transmission */ +#define USART_DENT_DISABLE CLT2_DENT(0) /*!< DMA request disable for transmission */ + +/* USART RTS configure */ +#define CLT2_RTSEN(regval) (BIT(8) & ((uint32_t)(regval) << 8)) +#define USART_RTS_ENABLE CLT2_RTSEN(1) /*!< RTS enable */ +#define USART_RTS_DISABLE CLT2_RTSEN(0) /*!< RTS disable */ + +/* USART CTS configure */ +#define CLT2_CTSEN(regval) (BIT(9) & ((uint32_t)(regval) << 9)) +#define USART_CTS_ENABLE CLT2_CTSEN(1) /*!< CTS enable */ +#define USART_CTS_DISABLE CLT2_CTSEN(0) /*!< CTS disable */ + +/* USART IrDA low-power enable */ +#define CTL2_IRLP(regval) (BIT(2) & ((uint32_t)(regval) << 2)) +#define USART_IRLP_LOW CTL2_IRLP(1) /*!< low-power */ +#define USART_IRLP_NORMAL CTL2_IRLP(0) /*!< normal */ + +/* function declarations */ +/* initialization functions */ +/* reset USART */ +void usart_deinit(uint32_t usart_periph); +/* configure USART baud rate value */ +void usart_baudrate_set(uint32_t usart_periph, uint32_t baudval); +/* configure USART parity function */ +void usart_parity_config(uint32_t usart_periph, uint32_t paritycfg); +/* configure USART word length */ +void usart_word_length_set(uint32_t usart_periph, uint32_t wlen); +/* configure USART stop bit length */ +void usart_stop_bit_set(uint32_t usart_periph, uint32_t stblen); + +/* USART normal mode communication */ +/* enable USART */ +void usart_enable(uint32_t usart_periph); +/* disable USART */ +void usart_disable(uint32_t usart_periph); +/* configure USART transmitter */ +void usart_transmit_config(uint32_t usart_periph, uint32_t txconfig); +/* configure USART receiver */ +void usart_receive_config(uint32_t usart_periph, uint32_t rxconfig); +/* USART transmit data function */ +void usart_data_transmit(uint32_t usart_periph, uint32_t data); +/* USART receive data function */ +uint16_t usart_data_receive(uint32_t usart_periph); + +/* multi-processor communication */ +/* configure address of the USART */ +void usart_address_config(uint32_t usart_periph, uint8_t addr); +/* enable mute mode */ +void usart_mute_mode_enable(uint32_t usart_periph); +/* disable mute mode */ +void usart_mute_mode_disable(uint32_t usart_periph); +/* configure wakeup method in mute mode */ +void usart_mute_mode_wakeup_config(uint32_t usart_periph, uint32_t wmethod); + +/* LIN mode communication */ +/* LIN mode enable */ +void usart_lin_mode_enable(uint32_t usart_periph); +/* LIN mode disable */ +void usart_lin_mode_disable(uint32_t usart_periph); +/* LIN break detection length */ +void usart_lin_break_detection_length_config(uint32_t usart_periph, uint32_t lblen); +/* send break frame */ +void usart_send_break(uint32_t usart_periph); + +/* half-duplex communication */ +/* half-duplex enable */ +void usart_halfduplex_enable(uint32_t usart_periph); +/* half-duplex disable */ +void usart_halfduplex_disable(uint32_t usart_periph); + +/* synchronous communication */ +/* clock enable */ +void usart_synchronous_clock_enable(uint32_t usart_periph); +/* clock disable */ +void usart_synchronous_clock_disable(uint32_t usart_periph); +/* configure usart synchronous mode parameters */ +void usart_synchronous_clock_config(uint32_t usart_periph, uint32_t clen, uint32_t cph, uint32_t cpl); + +/* smartcard communication */ +/* guard time value configure in smartcard mode */ +void usart_guard_time_config(uint32_t usart_periph, uint32_t gaut); +/* smartcard mode enable */ +void usart_smartcard_mode_enable(uint32_t usart_periph); +/* smartcard mode disable */ +void usart_smartcard_mode_disable(uint32_t usart_periph); +/* NACK enable in smartcard mode */ +void usart_smartcard_mode_nack_enable(uint32_t usart_periph); +/* NACK disable in smartcard mode */ +void usart_smartcard_mode_nack_disable(uint32_t usart_periph); + +/* IrDA communication */ +/* enable IrDA mode */ +void usart_irda_mode_enable(uint32_t usart_periph); +/* disable IrDA mode */ +void usart_irda_mode_disable(uint32_t usart_periph); +/* configure the peripheral clock prescaler */ +void usart_prescaler_config(uint32_t usart_periph, uint8_t psc); +/* configure IrDA low-power */ +void usart_irda_lowpower_config(uint32_t usart_periph, uint32_t irlp); + +/* hardware flow communication */ +/* configure hardware flow control RTS */ +void usart_hardware_flow_rts_config(uint32_t usart_periph, uint32_t rtsconfig); +/* configure hardware flow control CTS */ +void usart_hardware_flow_cts_config(uint32_t usart_periph, uint32_t ctsconfig); + +/* configure USART DMA for reception */ +void usart_dma_receive_config(uint32_t usart_periph, uint32_t dmacmd); +/* configure USART DMA for transmission */ +void usart_dma_transmit_config(uint32_t usart_periph, uint32_t dmacmd); + +/* flag functions */ +/* get flag in STAT register */ +FlagStatus usart_flag_get(uint32_t usart_periph, usart_flag_enum flag); +/* clear flag in STAT register */ +void usart_flag_clear(uint32_t usart_periph, usart_flag_enum flag); + +/* interrupt functions */ +/* enable USART interrupt */ +void usart_interrupt_enable(uint32_t usart_periph, uint32_t int_flag); +/* disable USART interrupt */ +void usart_interrupt_disable(uint32_t usart_periph, uint32_t int_flag); +/* get USART interrupt and flag status */ +FlagStatus usart_interrupt_flag_get(uint32_t usart_periph, uint32_t int_flag); +/* clear interrupt flag in STAT register */ +void usart_interrupt_flag_clear(uint32_t usart_periph, uint32_t flag); +int usart_write(uint32_t usart_periph,int ch); +uint8_t usart_read(uint32_t usart_periph); +#endif /* GD32VF103_USART_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_wwdgt.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_wwdgt.h new file mode 100644 index 00000000..7167bb12 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/gd32vf103_wwdgt.h @@ -0,0 +1,88 @@ +/*! + \file gd32vf103_wwdgt.h + \brief definitions for the WWDGT + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#ifndef GD32VF103_WWDGT_H +#define GD32VF103_WWDGT_H + +#include "gd32vf103.h" +#include "gd32vf103_rcu.h" +#include "gd32vf103_dbg.h" + +/* WWDGT definitions */ +#define WWDGT WWDGT_BASE /*!< WWDGT base address */ + +/* registers definitions */ +#define WWDGT_CTL REG32((WWDGT) + 0x00000000U) /*!< WWDGT control register */ +#define WWDGT_CFG REG32((WWDGT) + 0x00000004U) /*!< WWDGT configuration register */ +#define WWDGT_STAT REG32((WWDGT) + 0x00000008U) /*!< WWDGT status register */ + +/* bits definitions */ +/* WWDGT_CTL */ +#define WWDGT_CTL_CNT BITS(0,6) /*!< WWDGT counter value */ +#define WWDGT_CTL_WDGTEN BIT(7) /*!< WWDGT counter enable */ + +/* WWDGT_CFG */ +#define WWDGT_CFG_WIN BITS(0,6) /*!< WWDGT counter window value */ +#define WWDGT_CFG_PSC BITS(7,8) /*!< WWDGT prescaler divider value */ +#define WWDGT_CFG_EWIE BIT(9) /*!< early wakeup interrupt enable */ + +/* WWDGT_STAT */ +#define WWDGT_STAT_EWIF BIT(0) /*!< early wakeup interrupt flag */ + +/* constants definitions */ +#define CFG_PSC(regval) (BITS(7,8) & ((uint32_t)(regval) << 7)) /*!< write value to WWDGT_CFG_PSC bit field */ +#define WWDGT_CFG_PSC_DIV1 CFG_PSC(0) /*!< the time base of WWDGT = (PCLK1/4096)/1 */ +#define WWDGT_CFG_PSC_DIV2 CFG_PSC(1) /*!< the time base of WWDGT = (PCLK1/4096)/2 */ +#define WWDGT_CFG_PSC_DIV4 CFG_PSC(2) /*!< the time base of WWDGT = (PCLK1/4096)/4 */ +#define WWDGT_CFG_PSC_DIV8 CFG_PSC(3) /*!< the time base of WWDGT = (PCLK1/4096)/8 */ + +/* function declarations */ +/* reset the window watchdog timer configuration */ +void wwdgt_deinit(void); +/* start the window watchdog timer counter */ +void wwdgt_enable(void); + +/* configure the window watchdog timer counter value */ +void wwdgt_counter_update(uint16_t counter_value); +/* configure counter value, window value, and prescaler divider value */ +void wwdgt_config(uint16_t counter, uint16_t window, uint32_t prescaler); + +/* enable early wakeup interrupt of WWDGT */ +void wwdgt_interrupt_enable(void); +/* check early wakeup interrupt state of WWDGT */ +FlagStatus wwdgt_flag_get(void); +/* clear early wakeup interrupt state of WWDGT */ +void wwdgt_flag_clear(void); + +#endif /* GD32VF103_WWDGT_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/nuclei_sdk_soc.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/nuclei_sdk_soc.h new file mode 100644 index 00000000..3f9c7c34 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/nuclei_sdk_soc.h @@ -0,0 +1,16 @@ +// See LICENSE for license details. +#ifndef _NUCLEI_SDK_SOC_H +#define _NUCLEI_SDK_SOC_H + +#ifdef __cplusplus + extern "C" { +#endif + +#include "gd32vf103.h" +#include "gd32vf103_libopt.h" + + +#ifdef __cplusplus +} +#endif +#endif diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/system_gd32vf103.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/system_gd32vf103.h new file mode 100644 index 00000000..724ee7b4 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Include/system_gd32vf103.h @@ -0,0 +1,80 @@ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +/******************************************************************************* + * @file system_gd32vf103.h + * @brief NMSIS Nuclei N/NX Device Peripheral Access Layer Header File for + * Device gd32vf103 + * @version V1.00 + * @date 7. Jan 2020 + ******************************************************************************/ + +#ifndef __SYSTEM_GD32VF103_H__ +#define __SYSTEM_GD32VF103_H__ + +#ifdef __cplusplus +extern "C" { +#endif + +#include + +extern uint32_t SystemCoreClock; /*!< System Clock Frequency (Core Clock) */ + +/** + \brief Setup the microcontroller system. + + Initialize the System and update the SystemCoreClock variable. + */ +extern void SystemInit (void); + + +/** + \brief Update SystemCoreClock variable. + + Updates the SystemCoreClock with current core Clock retrieved from cpu registers. + */ +extern void SystemCoreClockUpdate (void); + +/** + * \brief Register an exception handler for exception code EXCn + */ +extern void Exception_Register_EXC(uint32_t EXCn, unsigned long exc_handler); + +/** + * \brief Get current exception handler for exception code EXCn + */ +extern unsigned long Exception_Get_EXC(uint32_t EXCn); + +/** + * \brief Initialize eclic config + */ +extern void ECLIC_Init(void); + +/** + * \brief Initialize a specific IRQ and register the handler + * \details + * This function set vector mode, trigger mode and polarity, interrupt level and priority, + * assign handler for specific IRQn. + */ +extern int32_t ECLIC_Register_IRQ(IRQn_Type IRQn, uint8_t shv, ECLIC_TRIGGER_Type trig_mode, uint8_t lvl, uint8_t priority, void *handler); + + +#ifdef __cplusplus +} +#endif + +#endif /* __SYSTEM_GD32VF103_H__ */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_core.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_core.c new file mode 100644 index 00000000..d5adc347 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_core.c @@ -0,0 +1,319 @@ +/*! + \file drv_usb_core.c + \brief USB core driver which can operate in host and device mode + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "drv_usb_core.h" +#include "drv_usb_hw.h" + +/*! + \brief config USB core to soft reset + \param[in] usb_regs: USB core registers + \param[out] none + \retval none +*/ +static void usb_core_reset (usb_core_regs *usb_regs) +{ + /* enable core soft reset */ + usb_regs->gr->GRSTCTL |= GRSTCTL_CSRST; + + /* wait for the core to be soft reset */ + while (usb_regs->gr->GRSTCTL & GRSTCTL_CSRST); + + /* wait for addtional 3 PHY clocks */ + usb_udelay(3); +} + +/*! + \brief config USB core basic + \param[in] usb_basic: pointer to usb capabilities + \param[in] usb_regs: USB core registers + \param[in] usb_core: USB core + \param[out] none + \retval operation status +*/ +usb_status usb_basic_init (usb_core_basic *usb_basic, + usb_core_regs *usb_regs, + usb_core_enum usb_core) +{ + uint32_t i = 0, reg_base = 0; + + /* config USB default transfer mode as FIFO mode */ + usb_basic->transfer_mode = USB_USE_FIFO; + + /* USB default speed is full-speed */ + usb_basic->core_speed = USB_SPEED_FULL; + + usb_basic->core_enum = usb_core; + + switch (usb_core) { + case USB_CORE_ENUM_HS: + reg_base = USBHS_REG_BASE; + + /* set the host channel numbers */ + usb_basic->num_pipe = USBHS_MAX_CHANNEL_COUNT; + + /* set the device endpoint numbers */ + usb_basic->num_ep = USBHS_MAX_EP_COUNT; + +#ifdef USB_ULPI_PHY_ENABLED + usb_basic->phy_itf = USB_ULPI_PHY; +#else + usb_basic->phy_itf = USB_EMBEDDED_PHY; +#endif /* USB_ULPI_PHY_ENABLED */ + +#ifdef USB_HS_INTERNAL_DMA_ENABLED + bp->transfer_mode = USB_USE_DMA; +#endif /* USB_HS_INTERNAL_DMA_ENABLED */ + break; + + case USB_CORE_ENUM_FS: + reg_base = USBFS_REG_BASE; + + /* set the host channel numbers */ + usb_basic->num_pipe = USBFS_MAX_CHANNEL_COUNT; + + /* set the device endpoint numbers */ + usb_basic->num_ep = USBFS_MAX_EP_COUNT; + + /* USBFS core use embedded physical layer */ + usb_basic->phy_itf = USB_EMBEDDED_PHY; + break; + + default: + return USB_FAIL; + } + + usb_basic->sof_enable = USB_SOF_OUTPUT; + usb_basic->low_power = USB_LOW_POWER; + + /* assign main registers address */ + *usb_regs = (usb_core_regs) { + .gr = (usb_gr*) (reg_base + USB_REG_OFFSET_CORE), + .hr = (usb_hr*) (reg_base + USB_REG_OFFSET_HOST), + .dr = (usb_dr*) (reg_base + USB_REG_OFFSET_DEV), + + .HPCS = (uint32_t*) (reg_base + USB_REG_OFFSET_PORT), + .PWRCLKCTL = (uint32_t*) (reg_base + USB_REG_OFFSET_PWRCLKCTL) + }; + + /* assign device endpoint registers address */ + for (i = 0; i < usb_basic->num_ep; i++) { + usb_regs->er_in[i] = (usb_erin *) \ + (reg_base + USB_REG_OFFSET_EP_IN + (i * USB_REG_OFFSET_EP)); + + usb_regs->er_out[i] = (usb_erout *)\ + (reg_base + USB_REG_OFFSET_EP_OUT + (i * USB_REG_OFFSET_EP)); + } + + /* assign host pipe registers address */ + for (i = 0; i < usb_basic->num_pipe; i++) { + usb_regs->pr[i] = (usb_pr *) \ + (reg_base + USB_REG_OFFSET_CH_INOUT + (i * USB_REG_OFFSET_CH)); + + usb_regs->DFIFO[i] = (uint32_t *) \ + (reg_base + USB_DATA_FIFO_OFFSET + (i * USB_DATA_FIFO_SIZE)); + } + + return USB_OK; +} + +/*! + \brief initializes the USB controller registers and + prepares the core device mode or host mode operation + \param[in] bp: usb capabilities + \param[in] core_regs: usb core registers + \param[out] none + \retval operation status +*/ +usb_status usb_core_init (usb_core_basic usb_basic, usb_core_regs *usb_regs) +{ + uint32_t reg_value = usb_regs->gr->GCCFG; + + /* disable USB global interrupt */ + usb_regs->gr->GAHBCS &= ~GAHBCS_GINTEN; + + if (USB_ULPI_PHY == usb_basic.phy_itf) { + reg_value &= ~GCCFG_PWRON; + + if (usb_basic.sof_enable) { + reg_value |= GCCFG_SOFOEN; + } + + usb_regs->gr->GCCFG = GCCFG_SOFOEN; + + /* init the ULPI interface */ + usb_regs->gr->GUSBCS &= ~(GUSBCS_EMBPHY | GUSBCS_ULPIEOI); + +#ifdef USBHS_EXTERNAL_VBUS_ENABLED + /* use external VBUS driver */ + usb_regs->gr->GUSBCS |= GUSBCS_ULPIEVD; +#else + /* use internal VBUS driver */ + usb_regs->gr->GUSBCS &= ~GUSBCS_ULPIEVD; +#endif + + /* soft reset the core */ + usb_core_reset (usb_regs); + } else { + usb_regs->gr->GUSBCS |= GUSBCS_EMBPHY; + + /* soft reset the core */ + usb_core_reset (usb_regs); + + /* active the transceiver and enable vbus sensing */ + reg_value = GCCFG_PWRON | GCCFG_VBUSACEN | GCCFG_VBUSBCEN; + +#ifndef VBUS_SENSING_ENABLED + reg_value |= GCCFG_VBUSIG; +#endif /* VBUS_SENSING_ENABLED */ + + /* enable SOF output */ + if (usb_basic.sof_enable) { + reg_value |= GCCFG_SOFOEN; + } + + usb_regs->gr->GCCFG = reg_value; + + usb_mdelay(20); + } + + if (USB_USE_DMA == usb_basic.transfer_mode) { + usb_regs->gr->GAHBCS |= GAHBCS_DMAEN; + usb_regs->gr->GAHBCS &= ~GAHBCS_BURST; + usb_regs->gr->GAHBCS |= DMA_INCR8; + } + +#ifdef USE_OTG_MODE + + /* enable USB OTG features */ + usb_regs->gr->GUSBCS |= GUSBCS_HNPCAP | GUSBCS_SRPCAP; + + /* enable the USB wakeup and suspend interrupts */ + usb_regs->gr->GINTF = 0xBFFFFFFFU; + + usb_regs->gr->GINTEN = GINTEN_WKUPIE | GINTEN_SPIE | \ + GINTEN_OTGIE | GINTEN_SESIE | GINTEN_CIDPSCIE; + +#endif /* USE_OTG_MODE */ + + return USB_OK; +} + +/*! + \brief write a packet into the Tx FIFO associated with the endpoint + \param[in] core_regs: usb core registers + \param[in] src_buf: pointer to source buffer + \param[in] fifo_num: FIFO number which is in (0..3) + \param[in] byte_count: packet byte count + \param[out] none + \retval operation status +*/ +usb_status usb_txfifo_write (usb_core_regs *usb_regs, + uint8_t *src_buf, + uint8_t fifo_num, + uint16_t byte_count) +{ + uint32_t word_count = (byte_count + 3U) / 4U; + + __IO uint32_t *fifo = usb_regs->DFIFO[fifo_num]; + + while (word_count-- > 0) { + *fifo = *(( uint32_t *)src_buf); + + src_buf += 4U; + } + + return USB_OK; +} + +/*! + \brief read a packet from the Rx FIFO associated with the endpoint + \param[in] core_regs: usb core registers + \param[in] dest_buf: pointer to destination buffer + \param[in] byte_count: packet byte count + \param[out] none + \retval void type pointer +*/ +void *usb_rxfifo_read (usb_core_regs *usb_regs, uint8_t *dest_buf, uint16_t byte_count) +{ + uint32_t word_count = (byte_count + 3U) / 4U; + + __IO uint32_t *fifo = usb_regs->DFIFO[0]; + + while (word_count-- > 0) { + *( uint32_t *)dest_buf = *fifo; + + dest_buf += 4U; + } + + return ((void *)dest_buf); +} + +/*! + \brief flush a Tx FIFO or all Tx FIFOs + \param[in] core_regs: pointer to usb core registers + \param[in] fifo_num: FIFO number which is in (0..3) + \param[out] none + \retval operation status +*/ +usb_status usb_txfifo_flush (usb_core_regs *usb_regs, uint8_t fifo_num) +{ + usb_regs->gr->GRSTCTL = ((uint32_t)fifo_num << 6U) | GRSTCTL_TXFF; + + /* wait for Tx FIFO flush bit is set */ + while (usb_regs->gr->GRSTCTL & GRSTCTL_TXFF); + + /* wait for 3 PHY clocks*/ + usb_udelay(3); + + return USB_OK; +} + +/*! + \brief flush the entire Rx FIFO + \param[in] core_regs: pointer to usb core registers + \param[out] none + \retval operation status +*/ +usb_status usb_rxfifo_flush (usb_core_regs *usb_regs) +{ + usb_regs->gr->GRSTCTL = GRSTCTL_RXFF; + + /* wait for Rx FIFO flush bit is set */ + while (usb_regs->gr->GRSTCTL & GRSTCTL_RXFF); + + /* wait for 3 PHY clocks */ + usb_udelay(3); + + return USB_OK; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_dev.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_dev.c new file mode 100644 index 00000000..e68919d1 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_dev.c @@ -0,0 +1,749 @@ +/*! + \file drv_usb_dev.c + \brief USB device mode low level driver + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ +#include "gd32vf103_libopt.h" +#include "drv_usb_hw.h" +#include "drv_usb_core.h" +#include "drv_usb_dev.h" + +/* endpoint 0 max packet length */ +static const uint8_t EP0_MAXLEN[4] = { + [DSTAT_EM_HS_PHY_30MHZ_60MHZ] = EP0MPL_64, + [DSTAT_EM_FS_PHY_30MHZ_60MHZ] = EP0MPL_64, + [DSTAT_EM_FS_PHY_48MHZ] = EP0MPL_64, + [DSTAT_EM_LS_PHY_6MHZ] = EP0MPL_8 +}; + +#ifdef USB_FS_CORE + +/* USB endpoint Tx FIFO size */ +static uint16_t USBFS_TX_FIFO_SIZE[USBFS_MAX_EP_COUNT] = +{ + (uint16_t)TX0_FIFO_FS_SIZE, + (uint16_t)TX1_FIFO_FS_SIZE, + (uint16_t)TX2_FIFO_FS_SIZE, + (uint16_t)TX3_FIFO_FS_SIZE +}; + +#elif defined(USB_HS_CORE) + +uint16_t USBHS_TX_FIFO_SIZE[USBHS_MAX_EP_COUNT] = +{ + (uint16_t)TX0_FIFO_HS_SIZE, + (uint16_t)TX1_FIFO_HS_SIZE, + (uint16_t)TX2_FIFO_HS_SIZE, + (uint16_t)TX3_FIFO_HS_SIZE, + (uint16_t)TX4_FIFO_HS_SIZE, + (uint16_t)TX5_FIFO_HS_SIZE +}; + +#endif /* USBFS_CORE */ + +/*! + \brief initialize USB core registers for device mode + \param[in] udev: pointer to usb device + \param[out] none + \retval operation status +*/ +usb_status usb_devcore_init (usb_core_driver *udev) +{ + uint32_t i, ram_addr = 0; + + /* force to peripheral mode */ + udev->regs.gr->GUSBCS &= ~(GUSBCS_FDM | GUSBCS_FHM); + udev->regs.gr->GUSBCS |= GUSBCS_FDM; + // udev->regs.gr->GUSBCS &= ~(GUSBCS_FHM); + + /* restart the Phy Clock (maybe don't need to...) */ + *udev->regs.PWRCLKCTL = 0U; + + /* config periodic frame interval to default value */ + udev->regs.dr->DCFG &= ~DCFG_EOPFT; + udev->regs.dr->DCFG |= FRAME_INTERVAL_80; + + udev->regs.dr->DCFG &= ~DCFG_DS; + +#ifdef USB_FS_CORE + if (udev->bp.core_enum == USB_CORE_ENUM_FS) { + /* set full-speed PHY */ + udev->regs.dr->DCFG |= USB_SPEED_INP_FULL; + + /* set Rx FIFO size */ + udev->regs.gr->GRFLEN = RX_FIFO_FS_SIZE; + + /* set endpoint 0 Tx FIFO length and RAM address */ + udev->regs.gr->DIEP0TFLEN_HNPTFLEN = ((uint32_t)TX0_FIFO_FS_SIZE << 16) | \ + ((uint32_t)RX_FIFO_FS_SIZE); + + ram_addr = RX_FIFO_FS_SIZE; + + /* set endpoint 1 to 3's Tx FIFO length and RAM address */ + for (i = 1; i < USBFS_MAX_EP_COUNT; i++) { + ram_addr += USBFS_TX_FIFO_SIZE[i - 1]; + + udev->regs.gr->DIEPTFLEN[i - 1] = ((uint32_t)USBFS_TX_FIFO_SIZE[i] << 16U) | \ + ram_addr; + } + } +#endif + +#ifdef USB_HS_CORE + if (udev->bp.core == USB_CORE_HS) { + if (udev->bp.core_phy == USB_ULPI_PHY) { + udev->regs.dr->DCFG |= USB_SPEED_EXP_HIGH; + } else {/* set High speed phy in Full speed mode */ + udev->regs.dr->DCFG |= USB_SPEED_EXP_FULL; + } + + /* Set Rx FIFO size */ + udev->regs.gr->GRFLEN &= ~GRFLEN_RXFD; + udev->regs.gr->GRFLEN |= RX_FIFO_HS_SIZE; + + /* Set endpoint 0 Tx FIFO length and RAM address */ + udev->regs.gr->DIEP0TFLEN_HNPTFLEN = ((uint32_t)TX0_FIFO_HS_SIZE << 16) | \ + RX_FIFO_HS_SIZE; + + ram_addr = RX_FIFO_HS_SIZE; + + /* Set endpoint 1 to 3's Tx FIFO length and RAM address */ + for (i = 1; i < USBHS_MAX_EP_COUNT; i++) { + ram_addr += USBHS_TX_FIFO_SIZE[i - 1]; + + udev->regs.gr->DIEPTFLEN[i - 1] = ((uint32_t)USBHS_TX_FIFO_SIZE[i] << 16) | \ + ram_addr; + } + } +#endif + + /* make sure all FIFOs are flushed */ + + /* flush all Tx FIFOs */ + usb_txfifo_flush (&udev->regs, 0x10); + + /* flush entire Rx FIFO */ + usb_rxfifo_flush (&udev->regs); + + /* clear all pending device interrupts */ + udev->regs.dr->DIEPINTEN = 0U; + udev->regs.dr->DOEPINTEN = 0U; + udev->regs.dr->DAEPINT = 0xFFFFFFFFU; + udev->regs.dr->DAEPINTEN = 0U; + + /* configure all IN/OUT endpoints */ + for (i = 0; i < udev->bp.num_ep; i++) { + if (udev->regs.er_in[i]->DIEPCTL & DEPCTL_EPEN) { + udev->regs.er_in[i]->DIEPCTL |= DEPCTL_EPD | DEPCTL_SNAK; + } else { + udev->regs.er_in[i]->DIEPCTL = 0U; + } + + /* set IN endpoint transfer length to 0 */ + udev->regs.er_in[i]->DIEPLEN = 0U; + + /* clear all pending IN endpoint interrupts */ + udev->regs.er_in[i]->DIEPINTF = 0xFFU; + + if (udev->regs.er_out[i]->DOEPCTL & DEPCTL_EPEN) { + udev->regs.er_out[i]->DOEPCTL |= DEPCTL_EPD | DEPCTL_SNAK; + } else { + udev->regs.er_out[i]->DOEPCTL = 0U; + } + + /* set OUT endpoint transfer length to 0 */ + udev->regs.er_out[i]->DOEPLEN = 0U; + + /* clear all pending OUT endpoint interrupts */ + udev->regs.er_out[i]->DOEPINTF = 0xFFU; + } + + usb_devint_enable (udev); + + return USB_OK; +} + +/*! + \brief enable the USB device mode interrupts + \param[in] udev: pointer to usb device + \param[out] none + \retval operation status +*/ +usb_status usb_devint_enable (usb_core_driver *udev) +{ + /* clear any pending USB OTG interrupts */ + udev->regs.gr->GOTGINTF = 0xFFFFFFFFU; + + /* clear any pending interrupts */ + udev->regs.gr->GINTF = 0xBFFFFFFFU; + + /* enable the USB wakeup and suspend interrupts */ + udev->regs.gr->GINTEN = GINTEN_WKUPIE | GINTEN_SPIE; + + /* enable device_mode-related interrupts */ + if (USB_USE_FIFO == udev->bp.transfer_mode) { + udev->regs.gr->GINTEN |= GINTEN_RXFNEIE; + } + udev->regs.gr->GINTEN |= GINTEN_RSTIE | GINTEN_ENUMFIE | GINTEN_IEPIE |\ + GINTEN_OEPIE | GINTEN_SOFIE | GINTEN_MFIE; + +#ifdef VBUS_SENSING_ENABLED + udev->regs.gr->GINTEN |= GINTEN_SESIE | GINTEN_OTGIE; +#endif /* VBUS_SENSING_ENABLED */ + + /* enable USB global interrupt */ + udev->regs.gr->GAHBCS |= GAHBCS_GINTEN; + + return USB_OK; +} + +/*! + \brief config the USB device to be disconnected + \param[in] udev: pointer to usb device + \param[out] none + \retval operation status +*/ +void usb_dev_disconnect (usb_core_driver *udev) +{ + udev->regs.dr->DCTL |= DCTL_SD; +} + +/*! + \brief config the USB device to be connected + \param[in] udev: pointer to usb device + \param[out] none + \retval operation status +*/ +void usb_dev_connect (usb_core_driver *udev) +{ + udev->regs.dr->DCTL &= ~DCTL_SD; +} + +/*! + \brief set the USB device address + \param[in] udev: pointer to usb device + \param[in] dev_addr: device address for setting + \param[out] none + \retval operation status +*/ +void usb_devaddr_set (usb_core_driver *udev, uint8_t dev_addr) +{ + udev->regs.dr->DCFG &= ~DCFG_DAR; + udev->regs.dr->DCFG |= dev_addr << 4; +} + +/*! + \brief active the usb transaction + \param[in] udev: pointer to usb device + \param[in] transc: the usb transaction + \param[out] none + \retval status +*/ +usb_status usb_transc_active (usb_core_driver *udev, usb_transc *transc) +{ + __IO uint32_t *reg_addr = NULL; + + __IO uint32_t epinten = 0U; + + /* get the endpoint number */ + uint8_t ep_num = transc->ep_addr.num; + + /* enable endpoint interrupt number */ + if (transc->ep_addr.dir) { + reg_addr = &udev->regs.er_in[ep_num]->DIEPCTL; + + epinten = 1 << ep_num; + } else { + reg_addr = &udev->regs.er_out[ep_num]->DOEPCTL; + + epinten = 1 << (16 + ep_num); + } + + /* if the endpoint is not active, need change the endpoint control register */ + if (!(*reg_addr & DEPCTL_EPACT)) { + *reg_addr &= ~(DEPCTL_MPL | DEPCTL_EPTYPE | DIEPCTL_TXFNUM); + + /* set endpoint maximum packet length */ + if (0U == ep_num) { + *reg_addr |= EP0_MAXLEN[udev->regs.dr->DSTAT & DSTAT_ES]; + } else { + *reg_addr |= transc->max_len; + } + + /* activate endpoint */ + *reg_addr |= (transc->ep_type << 18) | (ep_num << 22) | DEPCTL_SD0PID | DEPCTL_EPACT; + } + +#ifdef USB_OTG_HS_DEDICATED_EP1_ENABLED + if ((ep_num == 1) && (udev->bp.core == USB_HS_CORE_ID)) { + udev->regs.dr->DEP1INTEN |= epinten; + } + else +#endif + { + /* enable the interrupts for this endpoint */ + udev->regs.dr->DAEPINTEN |= epinten; + } + + return USB_OK; +} + +/*! + \brief deactive the usb transaction + \param[in] udev: pointer to usb device + \param[in] transc: the usb transaction + \param[out] none + \retval status +*/ +usb_status usb_transc_deactivate(usb_core_driver *udev, usb_transc *transc) +{ + uint32_t epinten = 0U; + + uint8_t ep_num = transc->ep_addr.num; + + /* disable endpoint interrupt number */ + if (transc->ep_addr.dir) { + epinten = 1 << ep_num; + + udev->regs.er_in[ep_num]->DIEPCTL &= ~DEPCTL_EPACT; + } else { + epinten = 1 << (ep_num + 16); + + udev->regs.er_out[ep_num]->DOEPCTL &= ~DEPCTL_EPACT; + } + +#ifdef USB_OTG_HS_DEDICATED_EP1_ENABLED + if ((ep_num == 1) && (udev->bp.core == USB_CORE_HS)) { + udev->regs.dr->DEP1INTEN &= ~epinten; + } + else +#endif + { + /* disable the interrupts for this endpoint */ + udev->regs.dr->DAEPINTEN &= ~epinten; + } + + return USB_OK; +} + +/*! + \brief configure usb transaction to start IN transfer + \param[in] udev: pointer to usb device + \param[in] transc: the usb IN transaction + \param[out] none + \retval status +*/ +usb_status usb_transc_inxfer (usb_core_driver *udev, usb_transc *transc) +{ + usb_status status = USB_OK; + + uint8_t ep_num = transc->ep_addr.num; + + __IO uint32_t epctl = udev->regs.er_in[ep_num]->DIEPCTL; + __IO uint32_t eplen = udev->regs.er_in[ep_num]->DIEPLEN; + + eplen &= ~(DEPLEN_TLEN | DEPLEN_PCNT); + + /* zero length packet or endpoint 0 */ + if (0U == transc->xfer_len) { + /* set transfer packet count to 1 */ + eplen |= 1 << 19; + } else { + /* set transfer packet count */ + if (0U == ep_num) { + transc->xfer_len = USB_MIN(transc->xfer_len, transc->max_len); + + eplen |= 1 << 19; + } else { + eplen |= ((transc->xfer_len - 1 + transc->max_len) / transc->max_len) << 19; + } + + /* set endpoint transfer length */ + eplen |= transc->xfer_len; + + if (transc->ep_type == USB_EPTYPE_ISOC) { + eplen |= DIEPLEN_MCNT; + } + } + + udev->regs.er_in[ep_num]->DIEPLEN = eplen; + + if (USB_USE_DMA == udev->bp.transfer_mode) { + udev->regs.er_in[ep_num]->DIEPDMAADDR = transc->dma_addr; + } + + if (transc->ep_type == USB_EPTYPE_ISOC) { + if (((udev->regs.dr->DSTAT & DSTAT_FNRSOF) >> 8) & 0x1) { + epctl |= DEPCTL_SD1PID; + } else { + epctl |= DEPCTL_SD0PID; + } + } + + /* enable the endpoint and clear the NAK */ + epctl |= DEPCTL_CNAK | DEPCTL_EPEN; + + udev->regs.er_in[ep_num]->DIEPCTL = epctl; + + if (transc->ep_type != USB_EPTYPE_ISOC) { + /* enable the Tx FIFO empty interrupt for this endpoint */ + if (transc->xfer_len > 0) { + udev->regs.dr->DIEPFEINTEN |= 1 << ep_num; + } + } else { + usb_txfifo_write (&udev->regs, transc->xfer_buf, ep_num, transc->xfer_len); + } + + return status; +} + +/*! + \brief configure usb transaction to start OUT transfer + \param[in] udev: pointer to usb device + \param[in] transc: the usb OUT transaction + \param[out] none + \retval status +*/ +usb_status usb_transc_outxfer (usb_core_driver *udev, usb_transc *transc) +{ + usb_status status = USB_OK; + + uint8_t ep_num = transc->ep_addr.num; + + uint32_t epctl = udev->regs.er_out[ep_num]->DOEPCTL; + uint32_t eplen = udev->regs.er_out[ep_num]->DOEPLEN; + + eplen &= ~(DEPLEN_TLEN | DEPLEN_PCNT); + + /* zero length packet or endpoint 0 */ + if ((0U == transc->xfer_len) || (0U == ep_num)) { + /* set the transfer length to max packet size */ + eplen |= transc->max_len; + + /* set the transfer packet count to 1 */ + eplen |= 1U << 19; + } else { + /* configure the transfer size and packet count as follows: + * pktcnt = N + * xfersize = N * maxpacket + */ + uint32_t packet_count = (transc->xfer_len + transc->max_len - 1) / transc->max_len; + + eplen |= packet_count << 19; + eplen |= packet_count * transc->max_len; + } + + udev->regs.er_out[ep_num]->DOEPLEN = eplen; + + if (USB_USE_DMA == udev->bp.transfer_mode) { + udev->regs.er_out[ep_num]->DOEPDMAADDR = transc->dma_addr; + } + + if (transc->ep_type == USB_EPTYPE_ISOC) { + if (transc->frame_num) { + epctl |= DEPCTL_SD1PID; + } else { + epctl |= DEPCTL_SD0PID; + } + } + + /* enable the endpoint and clear the NAK */ + epctl |= DEPCTL_EPEN | DEPCTL_CNAK; + + udev->regs.er_out[ep_num]->DOEPCTL = epctl; + + return status; +} + +/*! + \brief set the usb transaction STALL status + \param[in] udev: pointer to usb device + \param[in] transc: the usb transaction + \param[out] none + \retval status +*/ +usb_status usb_transc_stall (usb_core_driver *udev, usb_transc *transc) +{ + __IO uint32_t *reg_addr = NULL; + + uint8_t ep_num = transc->ep_addr.num; + + if (transc->ep_addr.dir) { + reg_addr = &(udev->regs.er_in[ep_num]->DIEPCTL); + + /* set the endpoint disable bit */ + if (*reg_addr & DEPCTL_EPEN) { + *reg_addr |= DEPCTL_EPD; + } + } else { + /* set the endpoint stall bit */ + reg_addr = &(udev->regs.er_out[ep_num]->DOEPCTL); + } + + /* set the endpoint stall bit */ + *reg_addr |= DEPCTL_STALL; + + return USB_OK; +} + +/*! + \brief clear the usb transaction STALL status + \param[in] udev: pointer to usb device + \param[in] transc: the usb transaction + \param[out] none + \retval status +*/ +usb_status usb_transc_clrstall(usb_core_driver *udev, usb_transc *transc) +{ + __IO uint32_t *reg_addr = NULL; + + uint8_t ep_num = transc->ep_addr.num; + + if (transc->ep_addr.dir) { + reg_addr = &(udev->regs.er_in[ep_num]->DIEPCTL); + } else { + reg_addr = &(udev->regs.er_out[ep_num]->DOEPCTL); + } + + /* clear the endpoint stall bits */ + *reg_addr &= ~DEPCTL_STALL; + + /* reset data PID of the periodic endpoints */ + if ((transc->ep_type == USB_EPTYPE_INTR) || (transc->ep_type == USB_EPTYPE_BULK)) { + *reg_addr |= DEPCTL_SD0PID; + } + + return USB_OK; +} + +/*! + \brief read device all OUT endpoint interrupt register + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +uint32_t usb_oepintnum_read (usb_core_driver *udev) +{ + uint32_t value = udev->regs.dr->DAEPINT; + + value &= udev->regs.dr->DAEPINTEN; + + return (value & DAEPINT_OEPITB) >> 16; +} + +/*! + \brief read device OUT endpoint interrupt flag register + \param[in] udev: pointer to usb device + \param[in] ep_num: endpoint number + \param[out] none + \retval none +*/ +uint32_t usb_oepintr_read (usb_core_driver *udev, uint8_t ep_num) +{ + uint32_t value = udev->regs.er_out[ep_num]->DOEPINTF; + + value &= udev->regs.dr->DOEPINTEN; + + return value; +} + +/*! + \brief read device all IN endpoint interrupt register + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +uint32_t usb_iepintnum_read (usb_core_driver *udev) +{ + uint32_t value = udev->regs.dr->DAEPINT; + + value &= udev->regs.dr->DAEPINTEN; + + return value & DAEPINT_IEPITB; +} + + +/*! + \brief read device IN endpoint interrupt flag register + \param[in] udev: pointer to usb device + \param[in] ep_num: endpoint number + \param[out] none + \retval none +*/ +uint32_t usb_iepintr_read (usb_core_driver *udev, uint8_t ep_num) +{ + uint32_t value = 0U, fifoemptymask = 0U, commonintmask = 0U; + + commonintmask = udev->regs.dr->DIEPINTEN; + fifoemptymask = udev->regs.dr->DIEPFEINTEN; + + /* check FIFO empty interrupt enable bit */ + commonintmask |= ((fifoemptymask >> ep_num) & 0x1U) << 7; + + value = udev->regs.er_in[ep_num]->DIEPINTF & commonintmask; + + return value; +} + +/*! + \brief configures OUT endpoint 0 to receive SETUP packets + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_ctlep_startout (usb_core_driver *udev) +{ + /* set OUT endpoint 0 receive length to 24 bytes, 1 packet and 3 setup packets */ + udev->regs.er_out[0]->DOEPLEN = DOEP0_TLEN(8U * 3U) | DOEP0_PCNT(1U) | DOEP0_STPCNT(3U); + + if (USB_USE_DMA == udev->bp.transfer_mode) { + udev->regs.er_out[0]->DOEPDMAADDR = (uint32_t)&udev->dev.control.req; + + /* endpoint enable */ + udev->regs.er_out[0]->DOEPCTL |= DEPCTL_EPACT | DEPCTL_EPEN; + } +} + +/*! + \brief set remote wakeup signalling + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_rwkup_set (usb_core_driver *udev) +{ + if (udev->dev.pm.dev_remote_wakeup) { + /* enable remote wakeup signaling */ + udev->regs.dr->DCTL |= DCTL_RWKUP; + } +} + +/*! + \brief reset remote wakeup signalling + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_rwkup_reset (usb_core_driver *udev) +{ + if (udev->dev.pm.dev_remote_wakeup) { + /* disable remote wakeup signaling */ + udev->regs.dr->DCTL &= ~DCTL_RWKUP; + } +} + +/*! + \brief active remote wakeup signalling + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_rwkup_active (usb_core_driver *udev) +{ + if (udev->dev.pm.dev_remote_wakeup) { + if (udev->regs.dr->DSTAT & DSTAT_SPST) { + if (udev->bp.low_power) { + /* ungate USB core clock */ + *udev->regs.PWRCLKCTL &= ~(PWRCLKCTL_SHCLK | PWRCLKCTL_SUCLK); + } + + /* active remote wakeup signaling */ + udev->regs.dr->DCTL |= DCTL_RWKUP; + + usb_mdelay(5); + + udev->regs.dr->DCTL &= ~DCTL_RWKUP; + } + } +} + +/*! + \brief active USB core clock + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_clock_active (usb_core_driver *udev) +{ + if (udev->bp.low_power) { + if (udev->regs.dr->DSTAT & DSTAT_SPST) { + /* un-gate USB Core clock */ + *udev->regs.PWRCLKCTL &= ~(PWRCLKCTL_SHCLK | PWRCLKCTL_SUCLK); + } + } +} + +/*! + \brief usb device suspend + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_dev_suspend (usb_core_driver *udev) +{ + __IO uint32_t devstat = udev->regs.dr->DSTAT; + + if ((udev->bp.low_power) && (devstat & DSTAT_SPST)) { + /* switch-off the USB clocks */ + *udev->regs.PWRCLKCTL |= PWRCLKCTL_SHCLK; + + /* enter DEEP_SLEEP mode with LDO in low power mode */ + pmu_to_deepsleepmode(PMU_LDO_LOWPOWER, WFI_CMD); + } +} + +/*! + \brief stop the device and clean up fifos + \param[in] udev: pointer to usb device + \param[out] none + \retval none +*/ +void usb_dev_stop (usb_core_driver *udev) +{ + uint32_t i; + + udev->dev.cur_status = 1; + + /* clear all interrupt flag and enable bits */ + for (i = 0; i < udev->bp.num_ep; i++) { + udev->regs.er_in[i]->DIEPINTF = 0xFFU; + udev->regs.er_out[i]->DOEPINTF = 0xFFU; + } + + udev->regs.dr->DIEPINTEN = 0U; + udev->regs.dr->DOEPINTEN = 0U; + udev->regs.dr->DAEPINTEN = 0U; + udev->regs.dr->DAEPINT = 0xFFFFFFFFU; + + /* flush the FIFO */ + usb_rxfifo_flush (&udev->regs); + usb_txfifo_flush (&udev->regs, 0x10); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_host.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_host.c new file mode 100644 index 00000000..0e09828c --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usb_host.c @@ -0,0 +1,514 @@ +/*! + \file drv_usb_host.c + \brief USB host mode low level driver + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "drv_usb_hw.h" +#include "drv_usb_core.h" +#include "drv_usb_host.h" + +const uint32_t PIPE_DPID[] = { + PIPE_DPID_DATA0, + PIPE_DPID_DATA1 +}; + +//__STATIC_INLINE uint8_t usb_frame_even (usb_core_driver *pudev) +uint32_t usb_frame_even (usb_core_driver *pudev) +{ + return !(pudev->regs.hr->HFINFR & 0x01U); +} + +//__STATIC_INLINE void usb_phyclock_config (usb_core_driver *pudev, uint8_t clock) +void usb_phyclock_config (usb_core_driver *pudev, uint8_t clock) +{ + pudev->regs.hr->HCTL &= ~HCTL_CLKSEL; + pudev->regs.hr->HCTL |= clock; +} + +//__STATIC_INLINE uint32_t usb_port_read (usb_core_driver *pudev) +uint32_t usb_port_read (usb_core_driver *pudev) +{ + return *pudev->regs.HPCS & ~(HPCS_PE | HPCS_PCD | HPCS_PEDC); +} + +//__STATIC_INLINE uint32_t usb_curspeed_get (usb_core_driver *pudev) + +uint32_t usb_curspeed_get (usb_core_driver *pudev) +{ + return *pudev->regs.HPCS & HPCS_PS; +} + +uint32_t usb_curframe_get (usb_core_driver *pudev) +{ + return (pudev->regs.hr->HFINFR & 0xFFFFU); +} + +/*! + \brief initializes USB core for host mode + \param[in] pudev: pointer to selected usb host + \param[out] none + \retval operation status +*/ +usb_status usb_host_init (usb_core_driver *pudev) +{ + uint32_t i = 0, inten = 0U; + + uint32_t nptxfifolen = 0U; + uint32_t ptxfifolen = 0U; + + pudev->regs.gr->GUSBCS &= ~GUSBCS_FDM; + pudev->regs.gr->GUSBCS |= GUSBCS_FHM; + + /* restart the PHY Clock */ + *pudev->regs.PWRCLKCTL = 0U; + + /* initialize host configuration register */ + if (USB_ULPI_PHY == pudev->bp.phy_itf) { + usb_phyclock_config (pudev, HCTL_30_60MHZ); + } else { + usb_phyclock_config (pudev, HCTL_48MHZ); + } + + usb_port_reset (pudev); + + /* support FS/LS only */ + pudev->regs.hr->HCTL &= ~HCTL_SPDFSLS; + + /* configure data FIFOs size */ +#ifdef USB_FS_CORE + if (USB_CORE_ENUM_FS == pudev->bp.core_enum) { + /* set Rx FIFO size */ + pudev->regs.gr->GRFLEN = USB_RX_FIFO_FS_SIZE; + + /* set non-periodic Tx FIFO size and address */ + nptxfifolen |= USB_RX_FIFO_FS_SIZE; + nptxfifolen |= USB_HTX_NPFIFO_FS_SIZE << 16U; + pudev->regs.gr->DIEP0TFLEN_HNPTFLEN = nptxfifolen; + + /* set periodic Tx FIFO size and address */ + ptxfifolen |= USB_RX_FIFO_FS_SIZE + USB_HTX_PFIFO_FS_SIZE; + ptxfifolen |= USB_HTX_PFIFO_FS_SIZE << 16U; + pudev->regs.gr->HPTFLEN = ptxfifolen; + } +#endif /* USB_FS_CORE */ + +#ifdef USB_HS_CORE + if (USB_CORE_HS == pudev->cfg.core) { + /* set Rx FIFO size */ + pudev->regs.gr->GRFLEN = USBHS_RX_FIFO_SIZE; + + /* set non-periodic Tx FIFO size and address */ + nptxfifolen |= USBHS_RX_FIFO_SIZE; + nptxfifolen |= USBHS_HTX_NPFIFO_SIZE; + pudev->regs.gr->DIEP0TFLEN_HNPTFLEN = nptxfifolen; + + /* set periodic Tx FIFO size and address */ + ptxfifolen |= USBHS_RX_FIFO_SIZE + USBHS_HTX_PFIFO_SIZE; + ptxfifolen |= USBHS_HTX_PFIFO_SIZE; + pudev->regs.gr->HPTFLEN = ptxfifolen; + } +#endif + +#ifdef USE_OTG_MODE + + /* clear host set hnp enable in the usb_otg control register */ + pudev->regs.gr->GOTGCS &= ~GOTGCS_HHNPEN; + +#endif + + /* disable all interrupts */ + pudev->regs.gr->GINTEN = 0U; + + /* clear any pending USB OTG interrupts */ + pudev->regs.gr->GOTGINTF = 0xFFFFFFFFU; + + /* enable the USB wakeup and suspend interrupts */ + pudev->regs.gr->GINTF = 0xBFFFFFFFU; + + /* make sure the FIFOs are flushed */ + + /* flush all Tx FIFOs in device or host mode */ + usb_txfifo_flush (&pudev->regs, 0x10U); + + /* flush the entire Rx FIFO */ + usb_rxfifo_flush (&pudev->regs); + + /* clear all pending host channel interrupts */ + for (i = 0U; i < pudev->bp.num_pipe; i++) { + pudev->regs.pr[i]->HCHINTF = 0xFFFFFFFFU; + pudev->regs.pr[i]->HCHINTEN = 0U; + } + +#ifndef USE_OTG_MODE + usb_portvbus_switch (pudev, 1U); +#endif /* USE_OTG_MODE */ + + pudev->regs.gr->GINTEN = GINTEN_WKUPIE | GINTEN_SPIE; + + /* enable host_mode-related interrupts */ + if (USB_USE_FIFO == pudev->bp.transfer_mode) { + inten = GINTEN_RXFNEIE; + } + + inten |= GINTEN_HPIE | GINTEN_HCIE | GINTEN_ISOINCIE; + + pudev->regs.gr->GINTEN |= inten; + + inten = GINTEN_DISCIE | GINTEN_SOFIE; + + pudev->regs.gr->GINTEN &= ~inten; + + pudev->regs.gr->GAHBCS |= GAHBCS_GINTEN; + + return USB_OK; +} + +/*! + \brief control the VBUS to power + \param[in] pudev: pointer to selected usb host + \param[in] state: VBUS state + \param[out] none + \retval none +*/ +void usb_portvbus_switch (usb_core_driver *pudev, uint8_t state) +{ + uint32_t port = 0U; + + /* enable or disable the external charge pump */ + usb_vbus_drive (state); + + /* turn on the host port power. */ + port = usb_port_read (pudev); + + if (!(port & HPCS_PP) && (1U == state)) { + port |= HPCS_PP; + } + + if ((port & HPCS_PP) && (0U == state)) { + port &= ~HPCS_PP; + } + + *pudev->regs.HPCS = port; + + usb_mdelay (200U); +} + +/*! + \brief reset host port + \param[in] pudev: pointer to usb device + \param[out] none + \retval operation status +*/ +uint32_t usb_port_reset (usb_core_driver *pudev) +{ + __IO uint32_t port = usb_port_read (pudev); + + *pudev->regs.HPCS = port | HPCS_PRST; + + usb_mdelay (100U); /* see note */ + + *pudev->regs.HPCS = port & ~HPCS_PRST; + + usb_mdelay (20U); + + return 1; +} + +/*! + \brief initialize host pipe + \param[in] pudev: pointer to usb device + \param[in] pipe_num: host pipe number which is in (0..7) + \param[out] none + \retval operation status +*/ +usb_status usb_pipe_init (usb_core_driver *pudev, uint8_t pipe_num) +{ + usb_status status = USB_OK; + + __IO uint32_t pp_ctl = 0U; + __IO uint32_t pp_inten = HCHINTEN_TFIE; + + usb_pipe *pp = &pudev->host.pipe[pipe_num]; + + /* clear old interrupt conditions for this host channel */ + pudev->regs.pr[pipe_num]->HCHINTF = 0xFFFFFFFFU; + + if (USB_USE_DMA == pudev->bp.transfer_mode) { + pp_inten |= HCHINTEN_DMAERIE; + } + + if (pp->ep.dir) { + pp_inten |= HCHINTEN_BBERIE; + } + + /* enable channel interrupts required for this transfer */ + switch (pp->ep.type) { + case USB_EPTYPE_CTRL: + case USB_EPTYPE_BULK: + pp_inten |= HCHINTEN_STALLIE | HCHINTEN_USBERIE \ + | HCHINTEN_DTERIE | HCHINTEN_NAKIE; + + if (!pp->ep.dir) { + pp_inten |= HCHINTEN_NYETIE; + + if (pp->ping) { + pp_inten |= HCHINTEN_ACKIE; + } + } + break; + + case USB_EPTYPE_INTR: + pp_inten |= HCHINTEN_STALLIE | HCHINTEN_USBERIE | HCHINTEN_DTERIE \ + | HCHINTEN_NAKIE | HCHINTEN_REQOVRIE; + break; + + case USB_EPTYPE_ISOC: + pp_inten |= HCHINTEN_REQOVRIE | HCHINTEN_ACKIE; + + if (pp->ep.dir) { + pp_inten |= HCHINTEN_USBERIE; + } + break; + + default: + break; + } + + pudev->regs.pr[pipe_num]->HCHINTEN = pp_inten; + + /* enable the top level host channel interrupt */ + pudev->regs.hr->HACHINTEN |= 1U << pipe_num; + + /* make sure host channel interrupts are enabled */ + pudev->regs.gr->GINTEN |= GINTEN_HCIE; + + /* program the host channel control register */ + pp_ctl |= PIPE_CTL_DAR(pp->dev_addr); + pp_ctl |= PIPE_CTL_EPNUM(pp->ep.num); + pp_ctl |= PIPE_CTL_EPDIR(pp->ep.dir); + pp_ctl |= PIPE_CTL_EPTYPE(pp->ep.type); + pp_ctl |= PIPE_CTL_LSD(pp->dev_speed == PORT_SPEED_LOW); + + pp_ctl |= pp->ep.mps; + pp_ctl |= ((uint32_t)(pp->ep.type == USB_EPTYPE_INTR) << 29U) & HCHCTL_ODDFRM; + + pudev->regs.pr[pipe_num]->HCHCTL = pp_ctl; + + return status; +} + +/*! + \brief prepare host channel for transferring packets + \param[in] pudev: pointer to usb device + \param[in] pipe_num: host pipe number which is in (0..7) + \param[out] none + \retval operation status +*/ +usb_status usb_pipe_xfer (usb_core_driver *pudev, uint8_t pipe_num) +{ + usb_status status = USB_OK; + + uint16_t dword_len = 0U; + uint16_t packet_count = 0U; + + __IO uint32_t pp_ctl = 0U; + + usb_pipe *pp = &pudev->host.pipe[pipe_num]; + + uint16_t max_packet_len = pp->ep.mps; + + /* compute the expected number of packets associated to the transfer */ + if (pp->xfer_len > 0U) { + packet_count = (pp->xfer_len + max_packet_len - 1U) / max_packet_len; + + if (packet_count > HC_MAX_PACKET_COUNT) { + packet_count = HC_MAX_PACKET_COUNT; + pp->xfer_len = packet_count * max_packet_len; + } + } else { + packet_count = 1U; + } + + if (pp->ep.dir) { + pp->xfer_len = packet_count * max_packet_len; + } + + /* initialize the host channel transfer information */ + pudev->regs.pr[pipe_num]->HCHLEN = pp->xfer_len | pp->DPID | PIPE_XFER_PCNT(packet_count); + + if (USB_USE_DMA == pudev->bp.transfer_mode) { + pudev->regs.pr[pipe_num]->HCHDMAADDR = (unsigned int)pp->xfer_buf; + } + + pp_ctl = pudev->regs.pr[pipe_num]->HCHCTL; + + if (usb_frame_even(pudev)) { + pp_ctl |= HCHCTL_ODDFRM; + } else { + pp_ctl &= ~HCHCTL_ODDFRM; + } + + /* set host channel enabled */ + pp_ctl |= HCHCTL_CEN; + pp_ctl &= ~HCHCTL_CDIS; + + pudev->regs.pr[pipe_num]->HCHCTL = pp_ctl; + + if (USB_USE_FIFO == pudev->bp.transfer_mode) { + if ((0U == pp->ep.dir) && (pp->xfer_len > 0U)) { + switch (pp->ep.type) { + /* non-periodic transfer */ + case USB_EPTYPE_CTRL: + case USB_EPTYPE_BULK: + dword_len = (pp->xfer_len + 3U) / 4U; + + /* check if there is enough space in fifo space */ + if (dword_len > (pudev->regs.gr->HNPTFQSTAT & HNPTFQSTAT_NPTXFS)) { + /* need to process data in nptxfempty interrupt */ + pudev->regs.gr->GINTEN |= GINTEN_NPTXFEIE; + } + break; + + /* periodic transfer */ + case USB_EPTYPE_INTR: + case USB_EPTYPE_ISOC: + dword_len = (pp->xfer_len + 3U) / 4U; + + /* check if there is enough space in fifo space */ + if (dword_len > (pudev->regs.hr->HPTFQSTAT & HPTFQSTAT_PTXFS)) { + /* need to process data in ptxfempty interrupt */ + pudev->regs.gr->GINTEN |= GINTEN_PTXFEIE; + } + break; + + default: + break; + } + + /* write packet into the tx fifo. */ + usb_txfifo_write (&pudev->regs, pp->xfer_buf, pipe_num, pp->xfer_len); + } + } + + return status; +} + +/*! + \brief halt pipe + \param[in] pudev: pointer to usb device + \param[in] pipe_num: host pipe number which is in (0..7) + \param[out] none + \retval operation status +*/ +usb_status usb_pipe_halt (usb_core_driver *pudev, uint8_t pipe_num) +{ + __IO uint32_t pp_ctl = pudev->regs.pr[pipe_num]->HCHCTL; + + uint8_t ep_type = (pp_ctl & HCHCTL_EPTYPE) >> 18U; + + pp_ctl |= HCHCTL_CEN | HCHCTL_CDIS; + + switch (ep_type) { + case USB_EPTYPE_CTRL: + case USB_EPTYPE_BULK: + if (0U == (pudev->regs.gr->HNPTFQSTAT & HNPTFQSTAT_NPTXFS)) { + pp_ctl &= ~HCHCTL_CEN; + } + break; + + case USB_EPTYPE_INTR: + case USB_EPTYPE_ISOC: + if (0U == (pudev->regs.hr->HPTFQSTAT & HPTFQSTAT_PTXFS)) { + pp_ctl &= ~HCHCTL_CEN; + } + break; + + default: + break; + } + + pudev->regs.pr[pipe_num]->HCHCTL = pp_ctl; + + return USB_OK; +} + +/*! + \brief configure host pipe to do ping operation + \param[in] pudev: pointer to usb device + \param[in] pipe_num: host pipe number which is in (0..7) + \param[out] none + \retval operation status +*/ +usb_status usb_pipe_ping (usb_core_driver *pudev, uint8_t pipe_num) +{ + uint32_t pp_ctl = 0U; + + pudev->regs.pr[pipe_num]->HCHLEN = HCHLEN_PING | (HCHLEN_PCNT & (1U << 19U)); + + pp_ctl = pudev->regs.pr[pipe_num]->HCHCTL; + + pp_ctl |= HCHCTL_CEN; + pp_ctl &= ~HCHCTL_CDIS; + + pudev->regs.pr[pipe_num]->HCHCTL = pp_ctl; + + return USB_OK; +} + +/*! + \brief stop the USB host and clean up FIFO + \param[in] none + \param[out] none + \retval none +*/ +void usb_host_stop (usb_core_driver *pudev) +{ + uint32_t i; + __IO uint32_t pp_ctl = 0U; + + pudev->regs.hr->HACHINTEN = 0x0U; + pudev->regs.hr->HACHINT = 0xFFFFFFFFU; + + /* flush out any leftover queued requests. */ + for (i = 0U; i < pudev->bp.num_pipe; i++) { + pp_ctl = pudev->regs.pr[i]->HCHCTL; + + pp_ctl &= ~(HCHCTL_CEN | HCHCTL_EPDIR); + pp_ctl |= HCHCTL_CDIS; + + pudev->regs.pr[i]->HCHCTL = pp_ctl; + } + + /* flush the FIFO */ + usb_rxfifo_flush (&pudev->regs); + usb_txfifo_flush (&pudev->regs, 0x10U); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbd_int.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbd_int.c new file mode 100644 index 00000000..14d2d1e3 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbd_int.c @@ -0,0 +1,595 @@ +/*! + \file drv_usbd_int.c + \brief USB device mode interrupt routines + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ +#include "gd32vf103_libopt.h" +//#include "usbd_conf.h" +#include "drv_usbd_int.h" +#include "usbd_transc.h" + +static uint32_t usbd_int_epout (usb_core_driver *udev); +static uint32_t usbd_int_epin (usb_core_driver *udev); +static uint32_t usbd_int_rxfifo (usb_core_driver *udev); +static uint32_t usbd_int_reset (usb_core_driver *udev); +static uint32_t usbd_int_enumfinish (usb_core_driver *udev); +static uint32_t usbd_int_suspend (usb_core_driver *udev); + +static uint32_t usbd_emptytxfifo_write (usb_core_driver *udev, uint32_t ep_num); + +static const uint8_t USB_SPEED[4] = { + [DSTAT_EM_HS_PHY_30MHZ_60MHZ] = USB_SPEED_HIGH, + [DSTAT_EM_FS_PHY_30MHZ_60MHZ] = USB_SPEED_FULL, + [DSTAT_EM_FS_PHY_48MHZ] = USB_SPEED_FULL, + [DSTAT_EM_LS_PHY_6MHZ] = USB_SPEED_LOW +}; + +__IO uint8_t setupc_flag = 0U; + +#ifdef USB_OTG_HS_DEDICATED_EP1_ENABLED + +/*! + \brief USB dedicated OUT endpoint 1 interrupt service routine handler + \param[in] udev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +uint32_t USBD_OTG_EP1OUT_ISR_Handler (usb_core_driver *udev) +{ + uint32_t oepintr = 0U; + uint32_t oeplen = 0U; + + oepintr = udev->regs.er_out[1]->DOEPINTF; + oepintr &= udev->regs.dr->DOEP1INTEN; + + /* Transfer complete */ + if (oepintr & DOEPINTF_TF) + { + /* Clear the bit in DOEPINTn for this interrupt */ + udev->regs.er_out[1]->DOEPINTF = DOEPINTF_TF; + + if (USB_USE_DMA == udev->bp.transfer_mode) + { + oeplen = udev->regs.er_out[1]->DOEPLEN; + + /* ToDo : handle more than one single MPS size packet */ + udev->dev.transc_out[1].xfer_count = udev->dev.transc_out[1].usb_transc - \ + oeplen & DEPLEN_TLEN; + } + + /* RX COMPLETE */ + USBD_DCD_INT_fops->DataOutStage(udev, 1); + } + + return 1; +} + +/*! + \brief USB dedicated IN endpoint 1 interrupt service routine handler + \param[in] udev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +uint32_t USBD_OTG_EP1IN_ISR_Handler (usb_core_driver *udev) +{ + uint32_t inten, intr, emptyen; + + inten = udev->regs.dr->DIEP1INTEN; + emptyen = udev->regs.dr->DIEPFEINTEN; + + inten |= ((emptyen >> 1 ) & 0x1) << 7; + + intr = udev->regs.er_in[1]->DIEPINTF & inten; + + if (intr & DIEPINTF_TF) + { + udev->regs.dr->DIEPFEINTEN &= ~(0x1 << 1); + + udev->regs.er_in[1]->DIEPINTF = DIEPINTF_TF; + + /* TX COMPLETE */ + USBD_DCD_INT_fops->DataInStage(udev, 1); + } + + if (intr & DIEPINTF_TXFE) + { + DCD_WriteEmptyTxFifo(udev, 1); + + udev->regs.er_in[1]->DIEPINTF = DIEPINTF_TXFE; + } + + return 1; +} + +#endif + + +/*! + \brief USB device-mode interrupts global service routine handler + \param[in] udev: pointer to usb device instance + \param[out] none + \retval none +*/ +void usbd_isr (usb_core_driver *udev) +{ + if (HOST_MODE != (udev->regs.gr->GINTF & GINTF_COPM)) { + uint32_t intr = udev->regs.gr->GINTF & udev->regs.gr->GINTEN; + + /* there are no interrupts, avoid spurious interrupt */ + if (!intr) { + return; + } + + /* OUT endpoints interrupts */ + if (intr & GINTF_OEPIF) { + usbd_int_epout (udev); + } + + /* IN endpoints interrupts */ + if (intr & GINTF_IEPIF) { + usbd_int_epin (udev); + } + + /* suspend interrupt */ + if (intr & GINTF_SP) { + usbd_int_suspend (udev); + } + + /* wakeup interrupt */ + if (intr & GINTF_WKUPIF) { + /* inform upper layer by the resume event */ + udev->dev.cur_status = udev->dev.backup_status; + + /* clear interrupt */ + udev->regs.gr->GINTF = GINTF_WKUPIF; + } + + /* wakeup interrupt */ + if (intr & GINTF_MFIF) { + + /* clear interrupt */ + udev->regs.gr->GINTF = GINTF_MFIF; + } + + /* start of frame interrupt */ + if (intr & GINTF_SOF) { + if (udev->dev.class_core->SOF) { + udev->dev.class_core->SOF(udev); + } + + if (0U != setupc_flag) { + setupc_flag ++; + + if (setupc_flag >= 3U) { + usbd_setup_transc (udev); + + setupc_flag = 0U; + } + } + + /* clear interrupt */ + udev->regs.gr->GINTF = GINTF_SOF; + } + + /* receive FIFO not empty interrupt */ + if (intr & GINTF_RXFNEIF) { + usbd_int_rxfifo (udev); + } + + /* USB reset interrupt */ + if (intr & GINTF_RST) { + usbd_int_reset (udev); + } + + /* enumeration has been done interrupt */ + if (intr & GINTF_ENUMFIF) { + usbd_int_enumfinish (udev); + } + + /* incomplete synchronization IN transfer interrupt*/ + if (intr & GINTF_ISOINCIF) { + if (NULL != udev->dev.class_core->incomplete_isoc_in) { + udev->dev.class_core->incomplete_isoc_in(udev); + } + + /* Clear interrupt */ + udev->regs.gr->GINTF = GINTF_ISOINCIF; + } + + /* incomplete synchronization OUT transfer interrupt*/ + if (intr & GINTF_ISOONCIF) { + if (NULL != udev->dev.class_core->incomplete_isoc_out) { + udev->dev.class_core->incomplete_isoc_out(udev); + } + + /* clear interrupt */ + udev->regs.gr->GINTF = GINTF_ISOONCIF; + } + +#ifdef VBUS_SENSING_ENABLED + + /* Session request interrupt */ + if (intr & GINTF_SESIF) { + udev->regs.gr->GINTF = GINTF_SESIF; + } + + /* OTG mode interrupt */ + if (intr & GINTF_OTGIF) { + if(udev->regs.gr->GOTGINTF & GOTGINTF_SESEND) { + + } + + /* Clear OTG interrupt */ + udev->regs.gr->GINTF = GINTF_OTGIF; + } +#endif + } +} + +/*! + \brief indicates that an OUT endpoint has a pending interrupt + \param[in] udev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbd_int_epout (usb_core_driver *udev) +{ + uint32_t epintnum = 0U; + uint32_t ep_num = 0U; + + for (epintnum = usb_oepintnum_read (udev); epintnum; epintnum >>= 1, ep_num++) { + if (epintnum & 0x1) { + __IO uint32_t oepintr = usb_oepintr_read (udev, ep_num); + + /* transfer complete interrupt */ + if (oepintr & DOEPINTF_TF) { + /* clear the bit in DOEPINTF for this interrupt */ + udev->regs.er_out[ep_num]->DOEPINTF = DOEPINTF_TF; + + if (USB_USE_DMA == udev->bp.transfer_mode) { + __IO uint32_t eplen = udev->regs.er_out[ep_num]->DOEPLEN; + + udev->dev.transc_out[ep_num].xfer_count = udev->dev.transc_out[ep_num].max_len - \ + eplen & DEPLEN_TLEN; + } + + /* inform upper layer: data ready */ + usbd_out_transc (udev, ep_num); + + if (USB_USE_DMA == udev->bp.transfer_mode) { + if ((0U == ep_num) && (USB_CTL_STATUS_OUT == udev->dev.control.ctl_state)) { + usb_ctlep_startout (udev); + } + } + } + + /* setup phase finished interrupt (control endpoints) */ + if (oepintr & DOEPINTF_STPF) { + /* inform the upper layer that a setup packet is available */ + if ((0U == ep_num) && (0U != setupc_flag)) { + usbd_setup_transc (udev); + + setupc_flag = 0U; + + udev->regs.er_out[ep_num]->DOEPINTF = DOEPINTF_STPF; + } + } + } + } + + return 1; +} + +/*! + \brief indicates that an IN endpoint has a pending interrupt + \param[in] udev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbd_int_epin (usb_core_driver *udev) +{ + uint32_t epintnum = 0U; + uint32_t ep_num = 0U; + + for (epintnum = usb_iepintnum_read (udev); epintnum; epintnum >>= 1, ep_num++) { + if (epintnum & 0x1U) { + __IO uint32_t iepintr = usb_iepintr_read (udev, ep_num); + + if (iepintr & DIEPINTF_TF) { + udev->regs.er_in[ep_num]->DIEPINTF = DIEPINTF_TF; + + /* data transmittion is completed */ + usbd_in_transc (udev, ep_num); + + if (USB_USE_DMA == udev->bp.transfer_mode) { + if ((0U == ep_num) && (USB_CTL_STATUS_IN == udev->dev.control.ctl_state)) { + usb_ctlep_startout (udev); + } + } + } + + if (iepintr & DIEPINTF_TXFE) { + usbd_emptytxfifo_write (udev, ep_num); + + udev->regs.er_in[ep_num]->DIEPINTF = DIEPINTF_TXFE; + } + } + } + + return 1; +} + +/*! + \brief handle the RX status queue level interrupt + \param[in] udev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbd_int_rxfifo (usb_core_driver *udev) +{ + usb_transc *transc = NULL; + + uint8_t data_PID = 0; + uint32_t bcount = 0; + + __IO uint32_t devrxstat = 0; + + /* disable the Rx status queue non-empty interrupt */ + udev->regs.gr->GINTEN &= ~GINTEN_RXFNEIE; + + /* get the status from the top of the FIFO */ + devrxstat = udev->regs.gr->GRSTATP; + + transc = &udev->dev.transc_out[devrxstat & GRSTATRP_EPNUM]; + + bcount = (devrxstat & GRSTATRP_BCOUNT) >> 4; + data_PID = (devrxstat & GRSTATRP_DPID) >> 15; + + switch ((devrxstat & GRSTATRP_RPCKST) >> 17) { + case RSTAT_GOUT_NAK: + break; + + case RSTAT_DATA_UPDT: + if (bcount > 0) { + usb_rxfifo_read (&udev->regs, transc->xfer_buf, bcount); + + transc->xfer_buf += bcount; + transc->xfer_count += bcount; + } + break; + + case RSTAT_XFER_COMP: + /* trigger the OUT enpoint interrupt */ + break; + + case RSTAT_SETUP_COMP: + /* trigger the OUT enpoint interrupt */ + break; + + case RSTAT_SETUP_UPDT: + if ((transc->ep_addr.num == 0) && (bcount == 8) && (data_PID == DPID_DATA0)) { + /* copy the setup packet received in FIFO into the setup buffer in RAM */ + usb_rxfifo_read (&udev->regs, (uint8_t *)&udev->dev.control.req, bcount); + + transc->xfer_count += bcount; + + setupc_flag = 1; + } + break; + + default: + break; + } + + /* enable the Rx status queue level interrupt */ + udev->regs.gr->GINTEN |= GINTEN_RXFNEIE; + + return 1; +} + +/*! + \brief handle USB reset interrupt + \param[in] udev: pointer to usb device instance + \param[out] none + \retval status +*/ +static uint32_t usbd_int_reset (usb_core_driver *udev) +{ + uint32_t i; + + /* clear the remote wakeup signaling */ + udev->regs.dr->DCTL &= ~DCTL_RWKUP; + + /* flush the Tx FIFO */ + usb_txfifo_flush (&udev->regs, 0); + + for (i = 0; i < udev->bp.num_ep; i++) { + udev->regs.er_in[i]->DIEPINTF = 0xFFU; + udev->regs.er_out[i]->DOEPINTF = 0xFFU; + } + + /* clear all pending device endpoint interrupts */ + udev->regs.dr->DAEPINT = 0xFFFFFFFFU; + + /* enable endpoint 0 interrupts */ + udev->regs.dr->DAEPINTEN = 1U | (1U << 16); + + /* enable OUT endpoint interrupts */ + udev->regs.dr->DOEPINTEN = DOEPINTEN_STPFEN | DOEPINTEN_TFEN; + + /* enable IN endpoint interrupts */ + udev->regs.dr->DIEPINTEN = DIEPINTEN_TFEN; + + /* reset device address */ + udev->regs.dr->DCFG &= ~DCFG_DAR; + udev->dev.dev_addr = 0U; + + /* configure endpoint 0 to receive SETUP packets */ + usb_ctlep_startout (udev); + + /* clear USB reset interrupt */ + udev->regs.gr->GINTF = GINTF_RST; + + udev->dev.transc_out[0] = (usb_transc) { + .ep_type = USB_EPTYPE_CTRL, + .max_len = USB_FS_EP0_MAX_LEN + }; + + usb_transc_active (udev, &udev->dev.transc_out[0]); + + udev->dev.transc_in[0] = (usb_transc) { + .ep_addr = { + .dir = 1 + }, + + .ep_type = USB_EPTYPE_CTRL, + .max_len = USB_FS_EP0_MAX_LEN + }; + + usb_transc_active (udev, &udev->dev.transc_in[0]); + + /* upon reset call usr call back */ + udev->dev.cur_status = USBD_DEFAULT; + + return 1; +} + +/*! + \brief handle USB speed enumeration finish interrupt + \param[in] udev: pointer to usb device instance + \param[out] none + \retval status +*/ +static uint32_t usbd_int_enumfinish (usb_core_driver *udev) +{ + uint8_t enum_speed = (uint8_t)((udev->regs.dr->DSTAT & DSTAT_ES) >> 1U); + + udev->regs.dr->DCTL &= ~DCTL_CGINAK; + udev->regs.dr->DCTL |= DCTL_CGINAK; + + udev->regs.gr->GUSBCS &= ~GUSBCS_UTT; + + /* set USB turn-around time based on device speed and PHY interface */ + if (USB_SPEED[enum_speed] == USB_SPEED_HIGH) { + udev->bp.core_speed = USB_SPEED_HIGH; + + udev->regs.gr->GUSBCS |= 0x09 << 10; + } else { + udev->bp.core_speed = USB_SPEED_FULL; + + udev->regs.gr->GUSBCS |= 0x05 << 10; + } + + /* clear interrupt */ + udev->regs.gr->GINTF = GINTF_ENUMFIF; + + return 1; +} + +/*! + \brief USB suspend interrupt handler + \param[in] udev: pointer to USB device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbd_int_suspend (usb_core_driver *udev) +{ + __IO uint8_t low_power = udev->bp.low_power; + __IO uint8_t suspend = (uint8_t)(udev->regs.dr->DSTAT & DSTAT_SPST); + __IO uint8_t is_configured = (udev->dev.cur_status == USBD_CONFIGURED)? 1U : 0U; + + udev->dev.backup_status = udev->dev.cur_status; + udev->dev.cur_status = USBD_SUSPENDED; + + if (low_power && suspend && is_configured) { + /* switch-off the otg clocks */ + *udev->regs.PWRCLKCTL |= PWRCLKCTL_SUCLK | PWRCLKCTL_SHCLK; + + /* enter DEEP_SLEEP mode with LDO in low power mode */ + pmu_to_deepsleepmode(PMU_LDO_LOWPOWER, WFI_CMD); + } + + /* clear interrupt */ + udev->regs.gr->GINTF = GINTF_SP; + + return 1U; +} + +/*! + \brief check FIFO for the next packet to be loaded + \param[in] udev: pointer to usb device instance + \param[in] ep_num: endpoint identifier which is in (0..3) + \param[out] none + \retval status +*/ +static uint32_t usbd_emptytxfifo_write (usb_core_driver *udev, uint32_t ep_num) +{ + usb_transc *transc = NULL; + + uint32_t len = 0; + uint32_t word_count = 0; + + transc = &udev->dev.transc_in[ep_num]; + + len = transc->xfer_len - transc->xfer_count; + + /* get the data length to write */ + if (len > transc->max_len) { + len = transc->max_len; + } + + word_count = (len + 3) / 4; + + while (((udev->regs.er_in[ep_num]->DIEPTFSTAT & DIEPTFSTAT_IEPTFS) > word_count) && \ + (transc->xfer_count < transc->xfer_len)) { + len = transc->xfer_len - transc->xfer_count; + + if (len > transc->max_len) { + len = transc->max_len; + } + + /* write FIFO in word(4bytes) */ + word_count = (len + 3) / 4; + + /* write the FIFO */ + usb_txfifo_write (&udev->regs, transc->xfer_buf, ep_num, len); + + transc->xfer_buf += len; + transc->xfer_count += len; + + if (transc->xfer_count == transc->xfer_len) { + /* disable the device endpoint FIFO empty interrupt */ + udev->regs.dr->DIEPFEINTEN &= ~(0x01 << ep_num); + } + } + + return 1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbh_int.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbh_int.c new file mode 100644 index 00000000..316ce1d2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/drv_usbh_int.c @@ -0,0 +1,536 @@ +/*! + \file drv_usbh_int.c + \brief USB host mode interrupt handler file + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "drv_usb_core.h" +#include "drv_usb_host.h" +#include "drv_usbh_int.h" + +#if defined (__GNUC__) /*!< GNU compiler */ + #pragma GCC optimize ("O0") +#endif /* __GNUC__ */ + +static uint32_t usbh_int_port (usb_core_driver *pudev); +static uint32_t usbh_int_pipe (usb_core_driver *pudev); +static uint32_t usbh_int_pipe_in (usb_core_driver *pudev, uint32_t pp_num); +static uint32_t usbh_int_pipe_out (usb_core_driver *pudev, uint32_t pp_num); +static uint32_t usbh_int_rxfifonoempty (usb_core_driver *pudev); +static uint32_t usbh_int_txfifoempty (usb_core_driver *pudev, usb_pipe_mode pp_mode); + +static inline void usb_pp_halt (usb_core_driver *pudev, + uint8_t pp_num, + uint32_t pp_int, + usb_pipe_staus pp_status) +{ + pudev->regs.pr[pp_num]->HCHINTEN |= HCHINTEN_CHIE; + + usb_pipe_halt(pudev, pp_num); + + pudev->regs.pr[pp_num]->HCHINTF = pp_int; + + pudev->host.pipe[pp_num].pp_status = pp_status; +} + +/*! + \brief handle global host interrupt + \param[in] pudev: pointer to usb core instance + \param[out] none + \retval operation status +*/ +uint32_t usbh_isr (usb_core_driver *pudev) +{ + uint32_t Retval = 0U; + + __IO uint32_t intr = 0U; + + /* check if host mode */ + if (HOST_MODE == (pudev->regs.gr->GINTF & GINTF_COPM)) { + intr = usb_coreintr_get(&pudev->regs); + + if (!intr) { + return 0; + } + + if (intr & GINTF_SOF) { + usbh_int_fop->SOF(pudev); + + /* clear interrupt */ + pudev->regs.gr->GINTF = GINTF_SOF; + } + + if (intr & GINTF_RXFNEIF) { + Retval |= usbh_int_rxfifonoempty (pudev); + } + + if (intr & GINTF_NPTXFEIF) { + Retval |= usbh_int_txfifoempty (pudev, PIPE_NON_PERIOD); + } + + if (intr & GINTF_PTXFEIF) { + Retval |= usbh_int_txfifoempty (pudev, PIPE_PERIOD); + } + + if (intr & GINTF_HCIF) { + Retval |= usbh_int_pipe (pudev); + } + + if (intr & GINTF_HPIF) { + Retval |= usbh_int_port (pudev); + } + + if (intr & GINTF_DISCIF) { + pudev->host.connect_status = 0U; + + /* clear interrupt */ + pudev->regs.gr->GINTF = GINTF_DISCIF; + } + + if (intr & GINTF_ISOONCIF) { + pudev->regs.pr[0]->HCHCTL |= HCHCTL_CEN | HCHCTL_CDIS; + + /* clear interrupt */ + pudev->regs.gr->GINTF = GINTF_ISOONCIF; + } + } + + return Retval; +} + +/*! + \brief handle all host channels interrupt + \param[in] pudev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbh_int_pipe (usb_core_driver *pudev) +{ + uint32_t pp_num = 0U; + uint32_t retval = 0U; + + for (pp_num = 0U; pp_num < pudev->bp.num_pipe; pp_num++) { + if ((pudev->regs.hr->HACHINT & HACHINT_HACHINT) & (1U << pp_num)) { + if (pudev->regs.pr[pp_num]->HCHCTL & HCHCTL_EPDIR) { + retval |= usbh_int_pipe_in (pudev, pp_num); + } else { + retval |= usbh_int_pipe_out (pudev, pp_num); + } + } + } + + return retval; +} + +/*! + \brief handle the TX FIFO empty interrupt + \param[in] pudev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbh_int_txfifoempty (usb_core_driver *pudev, usb_pipe_mode pp_mode) +{ + uint8_t pp_num = 0U; + uint16_t word_count = 0U, len = 0U; + __IO uint32_t *txfiforeg = 0U, txfifostate = 0U; + + if (PIPE_NON_PERIOD == pp_mode) { + txfiforeg = &pudev->regs.gr->HNPTFQSTAT; + } else if (PIPE_PERIOD == pp_mode) { + txfiforeg = &pudev->regs.hr->HPTFQSTAT; + } else { + return 0U; + } + + txfifostate = *txfiforeg; + + pp_num = (txfifostate & TFQSTAT_CNUM) >> 27U; + + word_count = (pudev->host.pipe[pp_num].xfer_len + 3U) / 4U; + + while (((txfifostate & TFQSTAT_TXFS) > word_count) && (0U != pudev->host.pipe[pp_num].xfer_len)) { + len = (txfifostate & TFQSTAT_TXFS) * 4U; + + if (len > pudev->host.pipe[pp_num].xfer_len) { + /* last packet */ + len = pudev->host.pipe[pp_num].xfer_len; + + if (PIPE_NON_PERIOD == pp_mode) { + pudev->regs.gr->GINTEN &= ~GINTEN_NPTXFEIE; + } else { + pudev->regs.gr->GINTEN &= ~GINTEN_PTXFEIE; + } + } + + word_count = (pudev->host.pipe[pp_num].xfer_len + 3U) / 4U; + usb_txfifo_write (&pudev->regs, pudev->host.pipe[pp_num].xfer_buf, pp_num, len); + + pudev->host.pipe[pp_num].xfer_buf += len; + pudev->host.pipe[pp_num].xfer_len -= len; + pudev->host.pipe[pp_num].xfer_count += len; + + txfifostate = *txfiforeg; + } + + return 1; +} + +/*! + \brief handle the host port interrupt + \param[in] pudev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbh_int_port (usb_core_driver *pudev) +{ + uint32_t retval = 0U; + + __IO uint32_t port_state = *pudev->regs.HPCS; + + /* clear the interrupt bits in GINTSTS */ + port_state &= ~(HPCS_PE | HPCS_PCD | HPCS_PEDC); + + /* port connect detected */ + if (*pudev->regs.HPCS & HPCS_PCD) { + port_state |= HPCS_PCD; + + pudev->host.connect_status = 1U; + + retval |= 1U; + } + + /* port enable changed */ + if (*pudev->regs.HPCS & HPCS_PEDC) { + port_state |= HPCS_PEDC; + + if (*pudev->regs.HPCS & HPCS_PE) { + uint32_t port_speed = usb_curspeed_get(pudev); + uint32_t clock_type = pudev->regs.hr->HCTL & HCTL_CLKSEL; + + pudev->host.connect_status = 1U; + + if (PORT_SPEED_LOW == port_speed) { + pudev->regs.hr->HFT = 6000U; + + if (HCTL_6MHZ != clock_type) { + if (USB_EMBEDDED_PHY == pudev->bp.phy_itf) { + usb_phyclock_config (pudev, HCTL_6MHZ); + } + } + } else if (PORT_SPEED_FULL == port_speed) { + pudev->regs.hr->HFT = 48000U; + + if (HCTL_48MHZ != clock_type) { + usb_phyclock_config (pudev, HCTL_48MHZ); + } + } else { + /* for high speed device and others */ + } + + pudev->host.port_enabled = 1U; + + pudev->regs.gr->GINTEN |= GINTEN_DISCIE; + } else { + pudev->host.port_enabled = 0U; + } + } + + /* clear port interrupts */ + *pudev->regs.HPCS = port_state; + + return retval; +} + +/*! + \brief handle the OUT channel interrupt + \param[in] pudev: pointer to usb device instance + \param[in] pp_num: host channel number which is in (0..7) + \param[out] none + \retval operation status +*/ +uint32_t usbh_int_pipe_out (usb_core_driver *pudev, uint32_t pp_num) +{ + usb_pr *pp_reg = pudev->regs.pr[pp_num]; + + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + uint32_t intr_pp = pp_reg->HCHINTF & pp_reg->HCHINTEN; + + if (intr_pp & HCHINTF_ACK) { + pp_reg->HCHINTF = HCHINTF_ACK; + } else if (intr_pp & HCHINTF_STALL) { + usb_pp_halt (pudev, pp_num, HCHINTF_STALL, PIPE_STALL); + } else if (intr_pp & HCHINTF_DTER) { + usb_pp_halt (pudev, pp_num, HCHINTF_DTER, PIPE_DTGERR); + pp_reg->HCHINTF = HCHINTF_NAK; + } else if (intr_pp & HCHINTF_REQOVR) { + usb_pp_halt (pudev, pp_num, HCHINTF_REQOVR, PIPE_REQOVR); + } else if (intr_pp & HCHINTF_TF) { + pp->err_count = 0U; + usb_pp_halt (pudev, pp_num, HCHINTF_TF, PIPE_XF); + } else if (intr_pp & HCHINTF_NAK) { + pp->err_count = 0U; + usb_pp_halt (pudev, pp_num, HCHINTF_NAK, PIPE_NAK); + } else if (intr_pp & HCHINTF_USBER) { + pp->err_count++; + usb_pp_halt (pudev, pp_num, HCHINTF_USBER, PIPE_TRACERR); + } else if (intr_pp & HCHINTF_NYET) { + pp->err_count = 0U; + usb_pp_halt (pudev, pp_num, HCHINTF_NYET, PIPE_NYET); + } else if (intr_pp & HCHINTF_CH) { + pudev->regs.pr[pp_num]->HCHINTEN &= ~HCHINTEN_CHIE; + + switch (pp->pp_status) { + case PIPE_XF: + pp->urb_state = URB_DONE; + + if (USB_EPTYPE_BULK == ((pp_reg->HCHCTL & HCHCTL_EPTYPE) >> 18U)) { + pp->data_toggle_out ^= 1U; + } + break; + + case PIPE_NAK: + pp->urb_state = URB_NOTREADY; + break; + + case PIPE_NYET: + if (1U == pudev->host.pipe[pp_num].ping) { + usb_pipe_ping (pudev, pp_num); + } + + pp->urb_state = URB_NOTREADY; + break; + + case PIPE_STALL: + pp->urb_state = URB_STALL; + break; + + case PIPE_TRACERR: + if (3U == pp->err_count) { + pp->urb_state = URB_ERROR; + pp->err_count = 0U; + } + break; + + default: + break; + } + + pp_reg->HCHINTF = HCHINTF_CH; + } + + return 1; +} + +/*! + \brief handle the IN channel interrupt + \param[in] pudev: pointer to usb device instance + \param[in] pp_num: host channel number which is in (0..7) + \param[out] none + \retval operation status +*/ +uint32_t usbh_int_pipe_in (usb_core_driver *pudev, uint32_t pp_num) +{ + usb_pr *pp_reg = pudev->regs.pr[pp_num]; + + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + __IO uint32_t intr_pp = pp_reg->HCHINTF & pp_reg->HCHINTEN; + + uint8_t ep_type = (pp_reg->HCHCTL & HCHCTL_EPTYPE) >> 18U; + + if (intr_pp & HCHINTF_ACK) { + pp_reg->HCHINTF = HCHINTF_ACK; + } else if (intr_pp & HCHINTF_STALL) { + usb_pp_halt (pudev, pp_num, HCHINTF_STALL, PIPE_STALL); + pp_reg->HCHINTF = HCHINTF_NAK; + + /* note: When there is a 'STALL', reset also nak, + else, the pudev->host.pp_status = HC_STALL + will be overwritten by 'NAK' in code below */ + intr_pp &= ~HCHINTF_NAK; + } else if (intr_pp & HCHINTF_DTER) { + usb_pp_halt (pudev, pp_num, HCHINTF_DTER, PIPE_DTGERR); + pp_reg->HCHINTF = HCHINTF_NAK; + } + + if (intr_pp & HCHINTF_REQOVR) { + usb_pp_halt (pudev, pp_num, HCHINTF_REQOVR, PIPE_REQOVR); + } else if (intr_pp & HCHINTF_TF) { + if (USB_USE_DMA == pudev->bp.transfer_mode) { + pudev->host.backup_xfercount[pp_num] = pp->xfer_len - pp_reg->HCHLEN & HCHLEN_TLEN; + } + + pp->pp_status = PIPE_XF; + pp->err_count = 0U; + + pp_reg->HCHINTF = HCHINTF_TF; + + switch (ep_type) { + case USB_EPTYPE_CTRL: + case USB_EPTYPE_BULK: + usb_pp_halt (pudev, pp_num, HCHINTF_NAK, PIPE_XF); + + pp->data_toggle_in ^= 1U; + break; + + case USB_EPTYPE_INTR: + pp_reg->HCHCTL |= HCHCTL_ODDFRM; + pp->urb_state = URB_DONE; + break; + + default: + break; + } + } else if (intr_pp & HCHINTF_CH) { + pp_reg->HCHINTEN &= ~HCHINTEN_CHIE; + + switch (pp->pp_status) { + case PIPE_XF: + pp->urb_state = URB_DONE; + break; + + case PIPE_STALL: + pp->urb_state = URB_STALL; + break; + + case PIPE_TRACERR: + case PIPE_DTGERR: + pp->err_count = 0U; + pp->urb_state = URB_ERROR; + break; + + default: + if(USB_EPTYPE_INTR == ep_type) { + pp->data_toggle_in ^= 1U; + } + break; + } + + pp_reg->HCHINTF = HCHINTF_CH; + } else if (intr_pp & HCHINTF_BBER) { + pp->err_count++; + usb_pp_halt (pudev, pp_num, HCHINTF_BBER, PIPE_TRACERR); + } else if (intr_pp & HCHINTF_NAK) { + switch (ep_type) { + case USB_EPTYPE_CTRL: + case USB_EPTYPE_BULK: + /* re-activate the channel */ + pp_reg->HCHCTL = (pp_reg->HCHCTL | HCHCTL_CEN) & ~HCHCTL_CDIS; + break; + + case USB_EPTYPE_INTR: + pp_reg->HCHINTEN |= HCHINTEN_CHIE; + + usb_pipe_halt(pudev, pp_num); + break; + + default: + break; + } + + pp->pp_status = PIPE_NAK; + + pp_reg->HCHINTF = HCHINTF_NAK; + } + + return 1; +} + +/*! + \brief handle the rx fifo non-empty interrupt + \param[in] pudev: pointer to usb device instance + \param[out] none + \retval operation status +*/ +static uint32_t usbh_int_rxfifonoempty (usb_core_driver *pudev) +{ + uint32_t count = 0U; + + __IO uint8_t pp_num = 0U; + __IO uint32_t rx_stat = 0U; + + /* disable the rx status queue level interrupt */ + pudev->regs.gr->GINTEN &= ~GINTEN_RXFNEIE; + + rx_stat = pudev->regs.gr->GRSTATP; + pp_num = rx_stat & GRSTATRP_CNUM; + + switch ((rx_stat & GRSTATRP_RPCKST) >> 17U) { + case GRXSTS_PKTSTS_IN: + count = (rx_stat & GRSTATRP_BCOUNT) >> 4U; + + /* read the data into the host buffer. */ + if ((count > 0U) && (NULL != pudev->host.pipe[pp_num].xfer_buf)) { + usb_rxfifo_read (&pudev->regs, pudev->host.pipe[pp_num].xfer_buf, count); + + /* manage multiple transfer packet */ + pudev->host.pipe[pp_num].xfer_buf += count; + pudev->host.pipe[pp_num].xfer_count += count; + + pudev->host.backup_xfercount[pp_num] = pudev->host.pipe[pp_num].xfer_count; + + if (pudev->regs.pr[pp_num]->HCHLEN & HCHLEN_PCNT) { + /* re-activate the channel when more packets are expected */ + __IO uint32_t pp_ctl = pudev->regs.pr[pp_num]->HCHCTL; + + pp_ctl |= HCHCTL_CEN; + pp_ctl &= ~HCHCTL_CDIS; + + pudev->regs.pr[pp_num]->HCHCTL = pp_ctl; + } + } + break; + + case GRXSTS_PKTSTS_IN_XFER_COMP: + break; + + case GRXSTS_PKTSTS_DATA_TOGGLE_ERR: + count = (rx_stat & GRSTATRP_BCOUNT) >> 4U; + + while (count > 0U) { + rx_stat = pudev->regs.gr->GRSTATP; + count--; + } + break; + + case GRXSTS_PKTSTS_CH_HALTED: + break; + + default: + break; + } + + /* enable the rx status queue level interrupt */ + pudev->regs.gr->GINTEN |= GINTEN_RXFNEIE; + + return 1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/gd32vf103_usb_hw.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/gd32vf103_usb_hw.c new file mode 100644 index 00000000..25bbcc47 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/gd32vf103_usb_hw.c @@ -0,0 +1,265 @@ +/*! + \file gd32vf103_usb_hw.c + \brief this file implements the board support package for the USB host library + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ +#include "gd32vf103_libopt.h" +#include "drv_usb_hw.h" +#include +#include +#include + + +#define TIM_MSEC_DELAY 0x01 +#define TIM_USEC_DELAY 0x02 + +#define HOST_POWERSW_PORT_RCC RCU_GPIOD +#define HOST_POWERSW_PORT GPIOD +#define HOST_POWERSW_VBUS GPIO_PIN_13 + +__IO uint32_t delay_time = 0; +__IO uint32_t usbfs_prescaler = 0; +__IO uint32_t timer_prescaler = 5; + +static void hwp_time_set (uint8_t unit); +static void hwp_delay (uint32_t ntime, uint8_t unit); + +/*! + \brief configure USB clock + \param[in] none + \param[out] none + \retval none +*/ +void usb_rcu_config (void) +{ + uint32_t system_clock = rcu_clock_freq_get(CK_SYS); + + if (system_clock == 48000000) { + usbfs_prescaler = RCU_CKUSB_CKPLL_DIV1; + timer_prescaler = 3; + } else if (system_clock == 72000000) { + usbfs_prescaler = RCU_CKUSB_CKPLL_DIV1_5; + timer_prescaler = 5; + } else if (system_clock == 96000000) { + usbfs_prescaler = RCU_CKUSB_CKPLL_DIV2; + timer_prescaler = 7; + } else { + /* reserved */ + } + + rcu_usb_clock_config(usbfs_prescaler); + rcu_periph_clock_enable(RCU_USBFS); +} + +/*! + \brief configure USB global interrupt + \param[in] none + \param[out] none + \retval none +*/ +void usb_intr_config (void) +{ + ECLIC_SetLevelIRQ(USBFS_IRQn,1); + ECLIC_SetPriorityIRQ(USBFS_IRQn,0); + ECLIC_EnableIRQ(USBFS_IRQn); +#ifdef USB_OTG_FS_LOW_PWR_MGMT_SUPPORT + + /* enable the power module clock */ + rcu_periph_clock_enable(RCU_PMU); + + /* USB wakeup EXTI line configuration */ + exti_interrupt_flag_clear(EXTI_18); + exti_init(EXTI_18, EXTI_INTERRUPT, EXTI_TRIG_RISING); + exti_interrupt_enable(EXTI_18); + + ECLIC_SetLevelIRQ(USBFS_WKUP_IRQn,3); + ECLIC_SetPriorityIRQ(USBFS_WKUP_IRQn,0); + ECLIC_EnableIRQ(USBFS_WKUP_IRQn); + +#endif /* USBHS_LOW_PWR_MGMT_SUPPORT */ +} + +/*! + \brief drives the VBUS signal through gpio + \param[in] state: VBUS states + \param[out] none + \retval none +*/ +void usb_vbus_drive (uint8_t state) +{ + if (0 == state) + { + /* DISABLE is needed on output of the Power Switch */ + gpio_bit_reset(HOST_POWERSW_PORT, HOST_POWERSW_VBUS); + } + else + { + /*ENABLE the Power Switch by driving the Enable LOW */ + gpio_bit_set(HOST_POWERSW_PORT, HOST_POWERSW_VBUS); + } +} + +/*! + \brief configures the GPIO for the VBUS + \param[in] none + \param[out] none + \retval none +*/ +void usb_vbus_config (void) +{ + rcu_periph_clock_enable(HOST_POWERSW_PORT_RCC); + + gpio_init(HOST_POWERSW_PORT, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, HOST_POWERSW_VBUS); + + /* by default, disable is needed on output of the power switch */ + gpio_bit_set(HOST_POWERSW_PORT, HOST_POWERSW_VBUS); + + /* Delay is need for stabilising the Vbus Low in Reset Condition, + * when Vbus=1 and Reset-button is pressed by user + */ + //usb_mdelay (1); + usb_mdelay (2); +} + +/*! + \brief initializes delay unit using Timer2 + \param[in] none + \param[out] none + \retval none +*/ +void usb_timer_init (void) +{ + rcu_periph_clock_enable(RCU_TIMER2); + + //eclic_irq_enable(TIMER2_IRQn, 2, 0); + /*ECLIC_Register_IRQn(TIMER2_IRQn, ECLIC_VECTOR_INTERRUPT, + ECLIC_LEVEL_TRIGGER, 2, 0, + TIMER2_IRQHandler);*/ +} + +/*! + \brief delay in micro seconds + \param[in] usec: value of delay required in micro seconds + \param[out] none + \retval none +*/ +void usb_udelay (const uint32_t usec) +{ + hwp_delay(usec, TIM_USEC_DELAY); +} + +/*! + \brief delay in milli seconds + \param[in] msec: value of delay required in milli seconds + \param[out] none + \retval none +*/ +void usb_mdelay (const uint32_t msec) +{ + hwp_delay(msec, TIM_MSEC_DELAY); +} + +/*! + \brief timer base IRQ + \param[in] none + \param[out] none + \retval none +*/ +void usb_timer_irq (void) +{ + if (timer_interrupt_flag_get(TIMER2, TIMER_INT_UP) != RESET){ + timer_interrupt_flag_clear(TIMER2, TIMER_INT_UP); + + if (delay_time > 0x00U){ + delay_time--; + } else { + timer_disable(TIMER2); + } + } +} + +/*! + \brief delay routine based on TIM2 + \param[in] ntime: delay Time + \param[in] unit: delay Time unit = mili sec / micro sec + \param[out] none + \retval none +*/ +static void hwp_delay(uint32_t ntime, uint8_t unit) +{ + delay_time = ntime; + hwp_time_set(unit); + + while(delay_time != 0); + + timer_disable(TIMER2); +} + +/*! + \brief configures TIM2 for delay routine based on TIM2 + \param[in] unit: msec /usec + \param[out] none + \retval none +*/ +static void hwp_time_set(uint8_t unit) +{ + timer_parameter_struct timer_basestructure; + + timer_disable(TIMER2); + timer_interrupt_disable(TIMER2, TIMER_INT_UP); + + if (unit == TIM_USEC_DELAY) { + timer_basestructure.period = 11; + } else if(unit == TIM_MSEC_DELAY) { + timer_basestructure.period = 11999; + } else { + /* no operation */ + } + + timer_basestructure.prescaler = timer_prescaler; + timer_basestructure.alignedmode = TIMER_COUNTER_EDGE; + timer_basestructure.counterdirection = TIMER_COUNTER_UP; + timer_basestructure.clockdivision = TIMER_CKDIV_DIV1; + timer_basestructure.repetitioncounter = 0; + + timer_init(TIMER2, &timer_basestructure); + + timer_interrupt_flag_clear(TIMER2, TIMER_INT_UP); + + timer_auto_reload_shadow_enable(TIMER2); + + /* timer2 interrupt enable */ + timer_interrupt_enable(TIMER2, TIMER_INT_UP); + + /* timer2 enable counter */ + timer_enable(TIMER2); +} + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_core.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_core.c new file mode 100644 index 00000000..02d73109 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_core.c @@ -0,0 +1,329 @@ +/*! + \file usbd_core.c + \brief USB device mode core functions + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "usbd_core.h" +#include "drv_usb_hw.h" + +/* endpoint type */ +const uint32_t ep_type[] = { + [USB_EP_ATTR_CTL] = USB_EPTYPE_CTRL, + [USB_EP_ATTR_BULK] = USB_EPTYPE_BULK, + [USB_EP_ATTR_INT] = USB_EPTYPE_INTR, + [USB_EP_ATTR_ISO] = USB_EPTYPE_ISOC +}; + +/*! + \brief initailizes the USB device-mode stack and load the class driver + \param[in] udev: pointer to USB core instance + \param[in] core: usb core type + \param[in] class_core: class driver + \param[out] none + \retval none +*/ +void usbd_init (usb_core_driver *udev, usb_core_enum core, usb_class_core *class_core) +{ + /* device descriptor, class and user callbacks */ + udev->dev.class_core = class_core; + + /* configure USB capabilites */ + usb_basic_init (&udev->bp, &udev->regs, core); + + /* initailizes the USB core*/ + usb_core_init (udev->bp, &udev->regs); + + /* set device disconnect */ + usbd_disconnect (udev); + + /* initailizes device mode */ + usb_devcore_init (udev); + + /* set device connect */ + usbd_connect (udev); + + udev->dev.cur_status = USBD_DEFAULT; +} + +/*! + \brief endpoint initialization + \param[in] udev: pointer to USB core instance + \param[in] ep_desc: pointer to endpoint descriptor + \param[out] none + \retval none +*/ +uint32_t usbd_ep_setup (usb_core_driver *udev, const usb_desc_ep *ep_desc) +{ + usb_transc *transc; + + uint8_t ep_addr = ep_desc->bEndpointAddress; + uint8_t max_len = ep_desc->wMaxPacketSize; + + /* set endpoint direction */ + if (EP_DIR(ep_addr)) { + transc = &udev->dev.transc_in[EP_ID(ep_addr)]; + + transc->ep_addr.dir = 1U; + } else { + transc = &udev->dev.transc_out[ep_addr]; + + transc->ep_addr.dir = 0U; + } + + transc->ep_addr.num = EP_ID(ep_addr); + transc->max_len = max_len; + transc->ep_type = ep_type[ep_desc->bmAttributes & USB_EPTYPE_MASK]; + + /* active USB endpoint function */ + usb_transc_active (udev, transc); + + return 0; +} + +/*! + \brief configure the endpoint when it is disabled + \param[in] udev: pointer to USB core instance + \param[in] ep_addr: endpoint address + in this parameter: + bit0..bit6: endpoint number (0..7) + bit7: endpoint direction which can be IN(1) or OUT(0) + \param[out] none + \retval none +*/ +uint32_t usbd_ep_clear (usb_core_driver *udev, uint8_t ep_addr) +{ + usb_transc *transc; + + if (EP_DIR(ep_addr)) { + transc = &udev->dev.transc_in[EP_ID(ep_addr)]; + } else { + transc = &udev->dev.transc_out[ep_addr]; + } + + /* deactive USB endpoint function */ + usb_transc_deactivate (udev, transc); + + return 0; +} + + +/*! + \brief endpoint prepare to receive data + \param[in] udev: pointer to usb core instance + \param[in] ep_addr: endpoint address + in this parameter: + bit0..bit6: endpoint number (0..7) + bit7: endpoint direction which can be IN(1) or OUT(0) + \param[in] pbuf: user buffer address pointer + \param[in] len: buffer length + \param[out] none + \retval none +*/ +uint32_t usbd_ep_recev (usb_core_driver *udev, uint8_t ep_addr, uint8_t *pbuf, uint16_t len) +{ + usb_transc *transc = &udev->dev.transc_out[EP_ID(ep_addr)]; + + /* setup the transfer */ + transc->xfer_buf = pbuf; + transc->xfer_len = len; + transc->xfer_count = 0; + + if (USB_USE_DMA == udev->bp.transfer_mode) { + transc->dma_addr = (uint32_t)pbuf; + } + + /* start the transfer */ + usb_transc_outxfer (udev, transc); + + return 0; +} + +/*! + \brief endpoint prepare to transmit data + \param[in] udev: pointer to USB core instance + \param[in] ep_addr: endpoint address + in this parameter: + bit0..bit6: endpoint number (0..7) + bit7: endpoint direction which can be IN(1) or OUT(0) + \param[in] pbuf: transmit buffer address pointer + \param[in] len: buffer length + \param[out] none + \retval none +*/ +uint32_t usbd_ep_send (usb_core_driver *udev, uint8_t ep_addr, uint8_t *pbuf, uint16_t len) +{ + usb_transc *transc = &udev->dev.transc_in[EP_ID(ep_addr)]; + + /* setup the transfer */ + transc->xfer_buf = pbuf; + transc->xfer_len = len; + transc->xfer_count = 0; + + if (USB_USE_DMA == udev->bp.transfer_mode) { + transc->dma_addr = (uint32_t)pbuf; + } + + /* start the transfer */ + usb_transc_inxfer (udev, transc); + + return 0; +} + +/*! + \brief set an endpoint to STALL status + \param[in] udev: pointer to USB core instance + \param[in] ep_addr: endpoint address + in this parameter: + bit0..bit6: endpoint number (0..7) + bit7: endpoint direction which can be IN(1) or OUT(0) + \param[out] none + \retval none +*/ +uint32_t usbd_ep_stall (usb_core_driver *udev, uint8_t ep_addr) +{ + usb_transc *transc = NULL; + + if (EP_DIR(ep_addr)) { + transc = &udev->dev.transc_in[EP_ID(ep_addr)]; + } else { + transc = &udev->dev.transc_out[ep_addr]; + } + + transc->ep_stall = 1; + + usb_transc_stall (udev, transc); + + return (0); +} + +/*! + \brief clear endpoint STALLed status + \param[in] udev: pointer to usb core instance + \param[in] ep_addr: endpoint address + in this parameter: + bit0..bit6: endpoint number (0..7) + bit7: endpoint direction which can be IN(1) or OUT(0) + \param[out] none + \retval none +*/ +uint32_t usbd_ep_stall_clear (usb_core_driver *udev, uint8_t ep_addr) +{ + usb_transc *transc = NULL; + + if (EP_DIR(ep_addr)) { + transc = &udev->dev.transc_in[EP_ID(ep_addr)]; + } else { + transc = &udev->dev.transc_out[ep_addr]; + } + + transc->ep_stall = 0; + + usb_transc_clrstall (udev, transc); + + return (0); +} + +/*! + \brief flush the endpoint FIFOs + \param[in] udev: pointer to usb core instance + \param[in] ep_addr: endpoint address + in this parameter: + bit0..bit6: endpoint number (0..7) + bit7: endpoint direction which can be IN(1) or OUT(0) + \param[out] none + \retval none +*/ +uint32_t usbd_fifo_flush (usb_core_driver *udev, uint8_t ep_addr) +{ + if (EP_DIR(ep_addr)) { + usb_txfifo_flush (&udev->regs, EP_ID(ep_addr)); + } else { + usb_rxfifo_flush (&udev->regs); + } + + return (0); +} + +/*! + \brief set USB device address + \param[in] udev: pointer to USB core instance + \param[in] addr: device address to set + \param[out] none + \retval none +*/ +void usbd_addr_set (usb_core_driver *udev, uint8_t addr) +{ + usb_devaddr_set(udev, addr); +} + +/*! + \brief get the received data length + \param[in] udev: pointer to USB device instance + \param[in] ep_num: endpoint number + \param[out] none + \retval USB device operation cur_status +*/ +uint16_t usbd_rxcount_get (usb_core_driver *udev, uint8_t ep_num) +{ + return udev->dev.transc_out[ep_num].xfer_count; +} + +/*! + \brief device connect + \param[in] udev: pointer to USB device instance + \param[out] none + \retval none +*/ +void usbd_connect (usb_core_driver *udev) +{ +#ifndef USE_OTG_MODE + /* connect device */ + usb_dev_connect (udev); + usb_mdelay(3); + +#endif /* USE_OTG_MODE */ +} + +/*! + \brief device disconnect + \param[in] udev: pointer to USB device instance + \param[out] none + \retval none +*/ +void usbd_disconnect (usb_core_driver *udev) +{ +#ifndef USE_OTG_MODE + /* disconnect device for 3ms */ + usb_dev_disconnect (udev); + usb_mdelay(3); +#endif /* USE_OTG_MODE */ +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_enum.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_enum.c new file mode 100644 index 00000000..39a75ba8 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_enum.c @@ -0,0 +1,696 @@ +/*! + \file usbd_enum.c + \brief USB enumeration function + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "usbd_enum.h" +#include "usb_ch9_std.h" + +static usb_reqsta _usb_std_getstatus (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_setaddress (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_setconfiguration (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_getconfiguration (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_getdescriptor (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_setfeature (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_clearfeature (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_reserved (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_setdescriptor (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_getinterface (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_setinterface (usb_core_driver *udev, usb_req *req); +static usb_reqsta _usb_std_synchframe (usb_core_driver *udev, usb_req *req); + +static uint8_t* _usb_dev_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len); +static uint8_t* _usb_config_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len); +static uint8_t* _usb_str_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len); +static uint8_t* _usb_bos_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len); + +static usb_reqsta (*_std_dev_req[])(usb_core_driver *udev, usb_req *req) = +{ + [USB_GET_STATUS] = _usb_std_getstatus, + [USB_CLEAR_FEATURE] = _usb_std_clearfeature, + [USB_RESERVED2] = _usb_std_reserved, + [USB_SET_FEATURE] = _usb_std_setfeature, + [USB_RESERVED4] = _usb_std_reserved, + [USB_SET_ADDRESS] = _usb_std_setaddress, + [USB_GET_DESCRIPTOR] = _usb_std_getdescriptor, + [USB_SET_DESCRIPTOR] = _usb_std_setdescriptor, + [USB_GET_CONFIGURATION] = _usb_std_getconfiguration, + [USB_SET_CONFIGURATION] = _usb_std_setconfiguration, + [USB_GET_INTERFACE] = _usb_std_getinterface, + [USB_SET_INTERFACE] = _usb_std_setinterface, + [USB_SYNCH_FRAME] = _usb_std_synchframe, +}; + +/* get standard descriptor handler */ +static uint8_t* (*std_desc_get[])(usb_core_driver *udev, uint8_t index, uint16_t *len) = { + [USB_DESCTYPE_DEV - 1] = _usb_dev_desc_get, + [USB_DESCTYPE_CONFIG - 1] = _usb_config_desc_get, + [USB_DESCTYPE_STR - 1] = _usb_str_desc_get +}; + +/*! + \brief handle USB standard device request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +usb_reqsta usbd_standard_request (usb_core_driver *udev, usb_req *req) +{ + return (*_std_dev_req[req->bRequest])(udev, req); +} + +/*! + \brief handle USB device class request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device class request + \param[out] none + \retval USB device request status +*/ +usb_reqsta usbd_class_request (usb_core_driver *udev, usb_req *req) +{ + if (USBD_CONFIGURED == udev->dev.cur_status) { + if (BYTE_LOW(req->wIndex) <= USBD_ITF_MAX_NUM) { + /* call device class handle function */ + return (usb_reqsta)udev->dev.class_core->req_proc(udev, req); + } + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB vendor request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB vendor request + \param[out] none + \retval USB device request status +*/ +usb_reqsta usbd_vendor_request (usb_core_driver *udev, usb_req *req) +{ + /* added by user... */ + + return REQ_SUPP; +} + +/*! + \brief no operation, just for reserved + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB vendor request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_reserved (usb_core_driver *udev, usb_req *req) +{ + /* no operation... */ + + return REQ_NOTSUPP; +} + +/*! + \brief get the device descriptor + \param[in] udev: pointer to USB device instance + \param[in] index: no use + \param[out] len: data length pointer + \retval descriptor buffer pointer +*/ +static uint8_t* _usb_dev_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len) +{ + *len = udev->dev.desc.dev_desc[0]; + + return udev->dev.desc.dev_desc; +} + +/*! + \brief get the configuration descriptor + \brief[in] udev: pointer to USB device instance + \brief[in] index: no use + \param[out] len: data length pointer + \retval descriptor buffer pointer +*/ +static uint8_t* _usb_config_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len) +{ + *len = udev->dev.desc.config_desc[2]; + + return udev->dev.desc.config_desc; +} + +/*! + \brief get the BOS descriptor + \brief[in] udev: pointer to USB device instance + \brief[in] index: no use + \param[out] len: data length pointer + \retval descriptor buffer pointer +*/ +static uint8_t* _usb_bos_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len) +{ + *len = udev->dev.desc.bos_desc[2]; + + return udev->dev.desc.bos_desc; +} + +/*! + \brief get string descriptor + \param[in] udev: pointer to USB device instance + \param[in] index: string descriptor index + \param[out] len: pointer to string length + \retval descriptor buffer pointer +*/ +static uint8_t* _usb_str_desc_get (usb_core_driver *udev, uint8_t index, uint16_t *len) +{ + uint8_t *desc = udev->dev.desc.strings[index]; + + *len = desc[0]; + + return desc; +} + +/*! + \brief handle Get_Status request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_getstatus (usb_core_driver *udev, usb_req *req) +{ + uint8_t recp = BYTE_LOW(req->wIndex); + + usb_transc *transc = &udev->dev.transc_in[0]; + + static uint8_t status[2] = {0}; + + switch(req->bmRequestType & USB_RECPTYPE_MASK) { + case USB_RECPTYPE_DEV: + if ((USBD_ADDRESSED == udev->dev.cur_status) || \ + (USBD_CONFIGURED == udev->dev.cur_status)) { + + if (udev->dev.pm.power_mode) { + status[0] = USB_STATUS_SELF_POWERED; + } else { + status[0] = 0U; + } + + if (udev->dev.pm.dev_remote_wakeup) { + status[0] |= USB_STATUS_REMOTE_WAKEUP; + } else { + status[0] = 0U; + } + + transc->xfer_buf = status; + transc->remain_len = 2U; + + return REQ_SUPP; + } + break; + + case USB_RECPTYPE_ITF: + if ((USBD_CONFIGURED == udev->dev.cur_status) && (recp <= USBD_ITF_MAX_NUM)) { + transc->xfer_buf = status; + transc->remain_len = 2U; + + return REQ_SUPP; + } + break; + + case USB_RECPTYPE_EP: + if (USBD_CONFIGURED == udev->dev.cur_status) { + if (0x80U == (recp & 0x80U)) { + status[0] = udev->dev.transc_in[EP_ID(recp)].ep_stall; + } else { + status[0] = udev->dev.transc_out[recp].ep_stall; + } + + transc->xfer_buf = status; + transc->remain_len = 2U; + + return REQ_SUPP; + } + break; + + default: + break; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Clear_Feature request + \param[in] udev: pointer to USB device instance + \param[in] req: USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_clearfeature (usb_core_driver *udev, usb_req *req) +{ + uint8_t ep = 0; + + switch(req->bmRequestType & USB_RECPTYPE_MASK) + { + case USB_RECPTYPE_DEV: + if ((USBD_ADDRESSED == udev->dev.cur_status) || \ + (USBD_CONFIGURED == udev->dev.cur_status)) { + + /* clear device remote wakeup feature */ + if (USB_FEATURE_REMOTE_WAKEUP == req->wValue) { + udev->dev.pm.dev_remote_wakeup = 0U; + + return REQ_SUPP; + } + } + break; + + case USB_RECPTYPE_ITF: + break; + + case USB_RECPTYPE_EP: + /* get endpoint address */ + ep = BYTE_LOW(req->wIndex); + + if (USBD_CONFIGURED == udev->dev.cur_status) { + /* clear endpoint halt feature */ + if ((USB_FEATURE_EP_HALT == req->wValue) && (!CTL_EP(ep))) { + usbd_ep_stall_clear (udev, ep); + + udev->dev.class_core->req_proc (udev, req); + } + + return REQ_SUPP; + } + break; + + default: + break; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Set_Feature request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_setfeature (usb_core_driver *udev, usb_req *req) +{ + uint8_t ep = 0; + + switch(req->bmRequestType & USB_RECPTYPE_MASK) + { + case USB_RECPTYPE_DEV: + if ((USBD_ADDRESSED == udev->dev.cur_status) || \ + (USBD_CONFIGURED == udev->dev.cur_status)) { + /* set device remote wakeup feature */ + if (USB_FEATURE_REMOTE_WAKEUP == req->wValue) { + udev->dev.pm.dev_remote_wakeup = 1U; + } + + return REQ_SUPP; + } + break; + + case USB_RECPTYPE_ITF: + break; + + case USB_RECPTYPE_EP: + /* get endpoint address */ + ep = BYTE_LOW(req->wIndex); + + if (USBD_CONFIGURED == udev->dev.cur_status) { + /* set endpoint halt feature */ + if ((USB_FEATURE_EP_HALT == req->wValue) && (!CTL_EP(ep))) { + usbd_ep_stall (udev, ep); + } + + return REQ_SUPP; + } + break; + + default: + break; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Set_Address request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_setaddress (usb_core_driver *udev, usb_req *req) +{ + if ((0U == req->wIndex) && (0U == req->wLength)) { + udev->dev.dev_addr = (uint8_t)(req->wValue) & 0x7FU; + + if (udev->dev.cur_status != USBD_CONFIGURED) { + usbd_addr_set (udev, udev->dev.dev_addr); + + if (udev->dev.dev_addr) { + udev->dev.cur_status = USBD_ADDRESSED; + } else { + udev->dev.cur_status = USBD_DEFAULT; + } + + return REQ_SUPP; + } + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Get_Descriptor request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_getdescriptor (usb_core_driver *udev, usb_req *req) +{ + uint8_t desc_type = 0; + uint8_t desc_index = 0; + + usb_transc *transc = &udev->dev.transc_in[0]; + + /* get device standard descriptor */ + switch (req->bmRequestType & USB_RECPTYPE_MASK) { + case USB_RECPTYPE_DEV: + desc_type = BYTE_HIGH(req->wValue); + desc_index = BYTE_LOW(req->wValue); + + switch (desc_type) { + case USB_DESCTYPE_DEV: + transc->xfer_buf = std_desc_get[desc_type - 1U](udev, desc_index, (uint16_t *)&(transc->remain_len)); + + if (64U == req->wLength) { + transc->remain_len = 8U; + } + break; + + case USB_DESCTYPE_CONFIG: + transc->xfer_buf = std_desc_get[desc_type - 1U](udev, desc_index, (uint16_t *)&(transc->remain_len)); + break; + + case USB_DESCTYPE_STR: + if (desc_index < STR_IDX_MAX) { + transc->xfer_buf = std_desc_get[desc_type - 1U](udev, desc_index, (uint16_t *)&(transc->remain_len)); + } + break; + + case USB_DESCTYPE_ITF: + case USB_DESCTYPE_EP: + case USB_DESCTYPE_DEV_QUALIFIER: + case USB_DESCTYPE_OTHER_SPD_CONFIG: + case USB_DESCTYPE_ITF_POWER: + break; + + case USB_DESCTYPE_BOS: + transc->xfer_buf = _usb_bos_desc_get(udev, desc_index, (uint16_t *)&(transc->remain_len)); + break; + + default: + break; + } + break; + + case USB_RECPTYPE_ITF: + /* get device class special descriptor */ + return (usb_reqsta)(udev->dev.class_core->req_proc(udev, req)); + + case USB_RECPTYPE_EP: + break; + + default: + break; + } + + if ((0U != transc->remain_len) && (0U != req->wLength)) { + if (transc->remain_len < req->wLength) { + if ((transc->remain_len >= transc->max_len) && (0U == (transc->remain_len % transc->max_len))) { + udev->dev.control.ctl_zlp = 1; + } + } else { + transc->remain_len = req->wLength; + } + + return REQ_SUPP; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Set_Descriptor request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_setdescriptor (usb_core_driver *udev, usb_req *req) +{ + /* no handle... */ + return REQ_SUPP; +} + +/*! + \brief handle USB Get_Configuration request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_getconfiguration (usb_core_driver *udev, usb_req *req) +{ + usb_transc *transc = &udev->dev.transc_in[0]; + + switch (udev->dev.cur_status) { + case USBD_ADDRESSED: + if (USB_DEFAULT_CONFIG == udev->dev.config) { + transc->xfer_buf = &(udev->dev.config); + transc->remain_len = 1U; + + return REQ_SUPP; + } + break; + + case USBD_CONFIGURED: + if (udev->dev.config != USB_DEFAULT_CONFIG) { + transc->xfer_buf = &(udev->dev.config); + transc->remain_len = 1U; + + return REQ_SUPP; + } + break; + + default: + break; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Set_Configuration request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_setconfiguration (usb_core_driver *udev, usb_req *req) +{ + static uint8_t config; + + config = (uint8_t)(req->wValue); + + if (config <= USBD_CFG_MAX_NUM) { + switch (udev->dev.cur_status) { + case USBD_ADDRESSED: + if (config){ + udev->dev.class_core->init(udev, config); + + udev->dev.config = config; + udev->dev.cur_status = USBD_CONFIGURED; + } + + return REQ_SUPP; + + case USBD_CONFIGURED: + if (USB_DEFAULT_CONFIG == config) { + udev->dev.class_core->deinit(udev, config); + + udev->dev.config = config; + udev->dev.cur_status = USBD_ADDRESSED; + } else if (config != udev->dev.config) { + /* clear old configuration */ + udev->dev.class_core->deinit(udev, config); + + /* set new configuration */ + udev->dev.config = config; + udev->dev.class_core->init(udev, config); + } + + return REQ_SUPP; + + case USBD_DEFAULT: + break; + + default: + break; + } + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Get_Interface request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_getinterface (usb_core_driver *udev, usb_req *req) +{ + switch (udev->dev.cur_status) { + case USBD_DEFAULT: + break; + + case USBD_ADDRESSED: + break; + + case USBD_CONFIGURED: + if (BYTE_LOW(req->wIndex) <= USBD_ITF_MAX_NUM) { + usb_transc *transc = &udev->dev.transc_in[0]; + + transc->xfer_buf = &(udev->dev.class_core->alter_set); + transc->remain_len = 1U; + + return REQ_SUPP; + } + break; + + default: + break; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB Set_Interface request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_setinterface (usb_core_driver *udev, usb_req *req) +{ + switch (udev->dev.cur_status) { + case USBD_DEFAULT: + break; + + case USBD_ADDRESSED: + break; + + case USBD_CONFIGURED: + if (BYTE_LOW(req->wIndex) <= USBD_ITF_MAX_NUM) { + udev->dev.class_core->alter_set = req->wValue; + + return REQ_SUPP; + } + break; + + default: + break; + } + + return REQ_NOTSUPP; +} + +/*! + \brief handle USB SynchFrame request + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval USB device request status +*/ +static usb_reqsta _usb_std_synchframe (usb_core_driver *udev, usb_req *req) +{ + /* no handle... */ + return REQ_SUPP; +} + +/*! + \brief handle USB enumeration error + \param[in] udev: pointer to USB device instance + \param[in] req: pointer to USB device request + \param[out] none + \retval none +*/ +void usbd_enum_error (usb_core_driver *udev, usb_req *req) +{ + usbd_ep_stall (udev, 0x80); + usbd_ep_stall (udev, 0x00); + + usb_ctlep_startout(udev); +} + +/*! + \brief convert hex 32bits value into unicode char + \param[in] value: hex 32bits value + \param[in] pbuf: buffer pointer to store unicode char + \param[in] len: value length + \param[out] none + \retval none +*/ +void int_to_unicode (uint32_t value, uint8_t *pbuf, uint8_t len) +{ + uint8_t index = 0; + + for (index = 0; index < len; index++) { + if ((value >> 28) < 0x0A) { + pbuf[2 * index] = (value >> 28) + '0'; + } else { + pbuf[2 * index] = (value >> 28) + 'A' - 10; + } + + value = value << 4; + + pbuf[2 * index + 1] = 0; + } +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_transc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_transc.c new file mode 100644 index 00000000..720b9bac --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbd_transc.c @@ -0,0 +1,254 @@ +/*! + \file usbd_transc.c + \brief USB transaction core functions + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "usbd_enum.h" +#include "usbd_transc.h" + +/*! + \brief USB send data in the control transaction + \param[in] udev: pointer to USB device instance + \param[out] none + \retval USB device operation cur_status +*/ +usbd_status usbd_ctl_send (usb_core_driver *udev) +{ + usb_transc *transc = &udev->dev.transc_in[0]; + + usbd_ep_send(udev, 0U, transc->xfer_buf, transc->remain_len); + + if (transc->remain_len > transc->max_len) { + udev->dev.control.ctl_state = USB_CTL_DATA_IN; + } else { + udev->dev.control.ctl_state = USB_CTL_LAST_DATA_IN; + } + + return USBD_OK; +} + +/*! + \brief USB receive data in control transaction + \param[in] udev: pointer to USB device instance + \param[out] none + \retval USB device operation cur_status +*/ +usbd_status usbd_ctl_recev (usb_core_driver *udev) +{ + usb_transc *transc = &udev->dev.transc_out[0]; + + usbd_ep_recev (udev, 0U, transc->xfer_buf, transc->remain_len); + + if (transc->remain_len > transc->max_len) { + udev->dev.control.ctl_state = USB_CTL_DATA_OUT; + } else { + udev->dev.control.ctl_state = USB_CTL_LAST_DATA_OUT; + } + + return USBD_OK; +} + +/*! + \brief USB send control transaction status + \param[in] udev: pointer to USB device instance + \param[out] none + \retval USB device operation cur_status +*/ +usbd_status usbd_ctl_status_send (usb_core_driver *udev) +{ + udev->dev.control.ctl_state = USB_CTL_STATUS_IN; + + usbd_ep_send (udev, 0U, NULL, 0U); + + usb_ctlep_startout(udev); + + return USBD_OK; +} + +/*! + \brief USB control receive status + \param[in] udev: pointer to USB device instance + \param[out] none + \retval USB device operation cur_status +*/ +usbd_status usbd_ctl_status_recev (usb_core_driver *udev) +{ + udev->dev.control.ctl_state = USB_CTL_STATUS_OUT; + + usbd_ep_recev (udev, 0, NULL, 0); + + usb_ctlep_startout(udev); + + return USBD_OK; +} + +/*! + \brief USB setup stage processing + \param[in] udev: pointer to USB device instance + \param[out] none + \retval USB device operation cur_status +*/ +uint8_t usbd_setup_transc (usb_core_driver *udev) +{ + usb_reqsta reqstat = REQ_NOTSUPP; + + usb_req req = udev->dev.control.req; + + switch (req.bmRequestType & USB_REQTYPE_MASK) { + /* standard device request */ + case USB_REQTYPE_STRD: + reqstat = usbd_standard_request (udev, &req); + break; + + /* device class request */ + case USB_REQTYPE_CLASS: + reqstat = usbd_class_request (udev, &req); + break; + + /* vendor defined request */ + case USB_REQTYPE_VENDOR: + reqstat = usbd_vendor_request (udev, &req); + break; + + default: + break; + } + + if (REQ_SUPP == reqstat) { + if (req.wLength == 0) { + usbd_ctl_status_send (udev); + } else { + if (req.bmRequestType & 0x80) { + usbd_ctl_send (udev); + } else { + usbd_ctl_recev (udev); + } + } + } else { + usbd_enum_error (udev, &req); + } + + return USBD_OK; +} + +/*! + \brief data out stage processing + \param[in] udev: pointer to USB device instance + \param[in] ep_num: endpoint identifier(0..7) + \param[out] none + \retval USB device operation cur_status +*/ +uint8_t usbd_out_transc (usb_core_driver *udev, uint8_t ep_num) +{ + if (ep_num == 0) { + usb_transc *transc = &udev->dev.transc_out[0]; + + switch (udev->dev.control.ctl_state) { + case USB_CTL_DATA_OUT: + /* update transfer length */ + transc->remain_len -= transc->max_len; + + usbd_ctl_recev (udev); + break; + + case USB_CTL_LAST_DATA_OUT: + if (udev->dev.cur_status == USBD_CONFIGURED) { + if (udev->dev.class_core->data_out != NULL) { + udev->dev.class_core->data_out (udev, 0U); + } + } + + transc->remain_len = 0U; + + usbd_ctl_status_send (udev); + break; + + default: + break; + } + } else if ((udev->dev.class_core->data_out != NULL) && (udev->dev.cur_status == USBD_CONFIGURED)) { + udev->dev.class_core->data_out (udev, ep_num); + } + + return USBD_OK; +} + +/*! + \brief data in stage processing + \param[in] udev: pointer to USB device instance + \param[in] ep_num: endpoint identifier(0..7) + \param[out] none + \retval USB device operation cur_status +*/ +uint8_t usbd_in_transc (usb_core_driver *udev, uint8_t ep_num) +{ + if (0U == ep_num) { + usb_transc *transc = &udev->dev.transc_in[0]; + + switch (udev->dev.control.ctl_state) { + case USB_CTL_DATA_IN: + /* update transfer length */ + transc->remain_len -= transc->max_len; + + usbd_ctl_send (udev); + break; + + case USB_CTL_LAST_DATA_IN: + /* last packet is MPS multiple, so send ZLP packet */ + if (udev->dev.control.ctl_zlp) { + usbd_ep_send (udev, 0U, NULL, 0U); + + udev->dev.control.ctl_zlp = 0U; + } else { + if (udev->dev.cur_status == USBD_CONFIGURED) { + if (udev->dev.class_core->data_in != NULL) { + udev->dev.class_core->data_in (udev, 0U); + } + } + + transc->remain_len = 0U; + + usbd_ctl_status_recev (udev); + } + break; + + default: + break; + } + } else { + if ((udev->dev.cur_status == USBD_CONFIGURED) && (udev->dev.class_core->data_in != NULL)) { + udev->dev.class_core->data_in (udev, ep_num); + } + } + + return USBD_OK; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_core.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_core.c new file mode 100644 index 00000000..91b434d2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_core.c @@ -0,0 +1,441 @@ +/*! + \file usbh_core.c + \brief USB host core state machine driver + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "drv_usb_hw.h" +#include "usbh_pipe.h" +#include "usbh_enum.h" +#include "usbh_core.h" +#include "drv_usbh_int.h" + +uint8_t usbh_sof (usb_core_driver *pudev); + +usbh_int_cb usbh_int_op = +{ + usbh_sof +}; + +usbh_int_cb *usbh_int_fop = &usbh_int_op; + +static usbh_status usbh_enum_task (usb_core_driver *pudev, usbh_host *puhost); + +/*! + \brief USB SOF callback function from the interrupt + \param[in] pudev: pointer to usb core instance + \param[out] none + \retval operation status +*/ +uint8_t usbh_sof (usb_core_driver *pudev) +{ + /* this callback could be used to implement a scheduler process */ + return 0U; +} + +/*! + \brief USB host stack initializations + \param[in] pudev: pointer to usb core instance + \param[in] core: USBFS core or USBHS core + \param[in] puhost: pointer to USB host + \param[out] none + \retval operation status +*/ +void usbh_init (usb_core_driver *pudev, usb_core_enum core, usbh_host *puhost) +{ + uint8_t i = 0U; + + /* host de-initializations */ + usbh_deinit(pudev, puhost); + + pudev->host.connect_status = 0U; + + for (i = 0U; i < USBFS_MAX_TX_FIFOS; i++) { + pudev->host.pipe[i].err_count = 0U; + pudev->host.pipe[i].pp_status = PIPE_IDLE; + pudev->host.backup_xfercount[i] = 0U; + } + + pudev->host.pipe[0].ep.mps = 8U; + + usb_basic_init (&pudev->bp, &pudev->regs, core); + +#ifndef DUAL_ROLE_MODE_ENABLED + + usb_core_init (pudev->bp, &pudev->regs); + + usb_host_init (pudev); + +#endif /* DUAL_ROLE_MODE_ENABLED */ + + /* upon init call usr call back */ + puhost->usr_cb->dev_init(); +} + +/*! + \brief de-initialize USB host + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval operation status +*/ +usbh_status usbh_deinit(usb_core_driver *pudev, usbh_host *puhost) +{ + /* software init */ + puhost->cur_state = HOST_DEFAULT; + puhost->backup_state = HOST_DEFAULT; + puhost->enum_state = ENUM_DEFAULT; + + puhost->control.ctl_state = CTL_IDLE; + puhost->control.max_len = USB_FS_EP0_MAX_LEN; + + puhost->dev_prop.addr = USBH_DEV_ADDR_DEFAULT; + puhost->dev_prop.speed = PORT_SPEED_FULL; + + usbh_pipe_free(pudev, puhost->control.pipe_in_num); + usbh_pipe_free(pudev, puhost->control.pipe_out_num); + + return USBH_OK; +} + +/*! + \brief USB host core main state machine process + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval none +*/ +void usbh_core_task (usb_core_driver *pudev, usbh_host *puhost) +{ + volatile usbh_status status = USBH_FAIL; + + /* check for host port events */ + if (((0U == pudev->host.connect_status) || (0U == pudev->host.port_enabled)) && (HOST_DEFAULT != puhost->cur_state)) { + if (puhost->cur_state != HOST_DEV_DETACHED) { + puhost->cur_state = HOST_DEV_DETACHED; + } + } + + switch (puhost->cur_state) { + case HOST_DEFAULT: + if (pudev->host.connect_status) { + puhost->cur_state = HOST_DETECT_DEV_SPEED; + + usb_mdelay (100U); + // usb_mdelay (2U); + usb_port_reset (pudev); + + puhost->usr_cb->dev_reset(); + } + break; + + case HOST_DETECT_DEV_SPEED: + if (pudev->host.port_enabled) { + puhost->cur_state = HOST_DEV_ATTACHED; + puhost->dev_prop.speed = usb_curspeed_get (pudev); + puhost->usr_cb->dev_speed_detected(puhost->dev_prop.speed); + + usb_mdelay (50U); + } + break; + + case HOST_DEV_ATTACHED: + puhost->usr_cb->dev_attach(); + puhost->control.pipe_out_num = usbh_pipe_allocate(pudev, 0x00U); + puhost->control.pipe_in_num = usbh_pipe_allocate(pudev, 0x80U); + + /* reset USB device */ + usb_port_reset (pudev); + + /* open IN control pipe */ + usbh_pipe_create (pudev, + &puhost->dev_prop, + puhost->control.pipe_in_num, + USB_EPTYPE_CTRL, + puhost->control.max_len); + + /* open OUT control pipe */ + usbh_pipe_create (pudev, + &puhost->dev_prop, + puhost->control.pipe_out_num, + USB_EPTYPE_CTRL, + puhost->control.max_len); + + puhost->cur_state = HOST_ENUM; + break; + + case HOST_ENUM: + + /* check for enumeration status */ + if (USBH_OK == usbh_enum_task (pudev, puhost)) { + /* the function shall return USBH_OK when full enumeration is complete */ + + /* user callback for end of device basic enumeration */ + puhost->usr_cb->dev_enumerated(); + puhost->cur_state = HOST_USER_INPUT; + } + break; + + case HOST_USER_INPUT: + /* the function should return user response true to move to class state */ + if (USBH_USER_RESP_OK == puhost->usr_cb->dev_user_input()) { + if ((USBH_OK == puhost->class_cb->class_init(pudev, puhost))) { + puhost->cur_state = HOST_CLASS_ENUM; + } + } + break; + + case HOST_CLASS_ENUM: + /* process class standard contol requests state machine */ + status = puhost->class_cb->class_requests(pudev, puhost); + + if (USBH_OK == status) { + puhost->cur_state = HOST_CLASS_HANDLER; + } else { + usbh_error_handler (puhost, status); + } + break; + + case HOST_CLASS_HANDLER: + /* process class state machine */ + status = puhost->class_cb->class_machine(pudev, puhost); + + usbh_error_handler (puhost, status); + break; + + case HOST_SUSPENDED: + break; + + case HOST_ERROR: + /* re-initilaize host for new enumeration */ + usbh_deinit (pudev, puhost); + puhost->usr_cb->dev_deinit(); + puhost->class_cb->class_deinit(pudev, puhost); + break; + + case HOST_DEV_DETACHED: + /* manage user disconnect operations*/ + puhost->usr_cb->dev_detach(); + + /* re-initilaize host for new enumeration */ + usbh_deinit(pudev, puhost); + puhost->usr_cb->dev_deinit(); + puhost->class_cb->class_deinit(pudev, puhost); + usbh_pipe_delete(pudev); + puhost->cur_state = HOST_DEFAULT; + break; + + default: + break; + } +} + +/*! + \brief handle the error on USB host side + \param[in] puhost: pointer to USB host + \param[in] err_type: type of error or busy/OK state + \param[out] none + \retval none +*/ +void usbh_error_handler (usbh_host *puhost, usbh_status err_type) +{ + /* error unrecovered or not supported device speed */ + if ((USBH_SPEED_UNKNOWN_ERROR == err_type) || (USBH_UNRECOVERED_ERROR == err_type)) { + puhost->usr_cb->dev_error(); + + puhost->cur_state = HOST_ERROR; + } else if (USBH_APPLY_DEINIT == err_type) { + puhost->cur_state = HOST_ERROR; + + /* user callback for initalization */ + puhost->usr_cb->dev_init(); + } +} + +/*! + \brief handle the USB enumeration task + \param[in] pudev: pointer to selected USB device + \param[in] puhost: pointer to host + \param[out] none + \retval none +*/ +static usbh_status usbh_enum_task (usb_core_driver *pudev, usbh_host *puhost) +{ + uint8_t str_buf[64]; + + usbh_status status = USBH_BUSY; + + static uint8_t index_mfc_str = 0U, index_prod_str = 0U, index_serial_str = 0U; + + switch (puhost->enum_state) { + case ENUM_DEFAULT: + /* get device descriptor for only 1st 8 bytes : to get ep0 maxpacketsize */ + if (USBH_OK == usbh_devdesc_get (pudev, puhost, 8U)) { + + puhost->control.max_len = puhost->dev_prop.dev_desc.bMaxPacketSize0; + + /* issue reset */ + usb_port_reset (pudev); + + /* modify control channels configuration for maximum packet size */ + usbh_pipe_update (pudev, + puhost->control.pipe_out_num, + 0U, 0U, + puhost->control.max_len); + + usbh_pipe_update (pudev, + puhost->control.pipe_in_num, + 0U, 0U, + puhost->control.max_len); + + puhost->enum_state = ENUM_GET_DEV_DESC; + + } + break; + + case ENUM_GET_DEV_DESC: + /* get full device descriptor */ + if (USBH_OK == usbh_devdesc_get (pudev, puhost, USB_DEV_DESC_LEN)) { + puhost->usr_cb->dev_devdesc_assigned(&puhost->dev_prop.dev_desc); + + index_mfc_str = puhost->dev_prop.dev_desc.iManufacturer; + index_prod_str = puhost->dev_prop.dev_desc.iProduct; + index_serial_str = puhost->dev_prop.dev_desc.iSerialNumber; + + puhost->enum_state = ENUM_SET_ADDR; + } + break; + + case ENUM_SET_ADDR: + /* set address */ + if (USBH_OK == usbh_setaddress (pudev, puhost, USBH_DEV_ADDR)) { + usb_mdelay (2); + + puhost->dev_prop.addr = USBH_DEV_ADDR; + + /* user callback for device address assigned */ + puhost->usr_cb->dev_address_set(); + + /* modify control channels to update device address */ + usbh_pipe_update (pudev, + puhost->control.pipe_in_num, + puhost->dev_prop.addr, + 0U, 0U); + + usbh_pipe_update (pudev, + puhost->control.pipe_out_num, + puhost->dev_prop.addr, + 0U, 0U); + + puhost->enum_state = ENUM_GET_CFG_DESC; + } + break; + + case ENUM_GET_CFG_DESC: + /* get standard configuration descriptor */ + if (USBH_OK == usbh_cfgdesc_get (pudev, puhost, USB_CFG_DESC_LEN)) { + puhost->enum_state = ENUM_GET_CFG_DESC_SET; + } + break; + + case ENUM_GET_CFG_DESC_SET: + /* get full config descriptor (config, interface, endpoints) */ + if (USBH_OK == usbh_cfgdesc_get (pudev, puhost, puhost->dev_prop.cfg_desc.wTotalLength)) { + /* user callback for configuration descriptors available */ + puhost->usr_cb->dev_cfgdesc_assigned (&puhost->dev_prop.cfg_desc, + puhost->dev_prop.itf_desc, + puhost->dev_prop.ep_desc[0]); + + puhost->enum_state = ENUM_GET_STR_DESC; + } + break; + + case ENUM_GET_STR_DESC: + if (index_mfc_str) { + if (USBH_OK == usbh_strdesc_get (pudev, + puhost, + puhost->dev_prop.dev_desc.iManufacturer, + str_buf, + 0xFFU)) { + /* user callback for manufacturing string */ + puhost->usr_cb->dev_mfc_str(str_buf); + + index_mfc_str = 0U; + } + } else { + if (index_prod_str) { + /* check that product string is available */ + if (USBH_OK == usbh_strdesc_get (pudev, + puhost, + puhost->dev_prop.dev_desc.iProduct, + str_buf, + 0xFFU)) { + puhost->usr_cb->dev_prod_str(str_buf); + + index_prod_str = 0U; + } + } else { + if (index_serial_str) { + if (USBH_OK == usbh_strdesc_get (pudev, + puhost, + puhost->dev_prop.dev_desc.iSerialNumber, + str_buf, + 0xFFU)) { + puhost->usr_cb->dev_seral_str(str_buf); + puhost->enum_state = ENUM_SET_CONFIGURATION; + + index_serial_str = 0U; + } + } else { + puhost->enum_state = ENUM_SET_CONFIGURATION; + } + } + } + break; + + case ENUM_SET_CONFIGURATION: + if (USBH_OK == usbh_setcfg (pudev, + puhost, + puhost->dev_prop.cfg_desc.bConfigurationValue)) { + puhost->enum_state = ENUM_DEV_CONFIGURED; + } + break; + + case ENUM_DEV_CONFIGURED: + status = USBH_OK; + break; + + default: + break; + } + + return status; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_enum.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_enum.c new file mode 100644 index 00000000..feaca6df --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_enum.c @@ -0,0 +1,549 @@ +/*! + \file usbh_enum.c + \brief USB host mode enumberation driver + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "usbh_transc.h" +#include "usbh_enum.h" + +static void usbh_devdesc_parse (usb_desc_dev *cfg_desc, uint8_t *buf, uint16_t len); +static void usbh_cfgset_parse (usb_dev_prop *udev, uint8_t *buf); +static void usbh_cfgdesc_parse (usb_desc_config *cfg_desc, uint8_t *buf); +static void usbh_itfdesc_parse (usb_desc_itf *itf_desc, uint8_t *buf); +static void usbh_epdesc_parse (usb_desc_ep *ep_desc, uint8_t *buf); +static void usbh_strdesc_parse (uint8_t *psrc, uint8_t *pdest, uint16_t len); + + +/*! + \brief configure USB control status parameters + \param[in] puhost: pointer to usb host + \param[in] buf: control transfer data buffer pointer + \param[in] len: length of the data buffer + \param[out] none + \retval none +*/ +void usbh_ctlstate_config (usbh_host *puhost, uint8_t *buf, uint16_t len) +{ + /* prepare the transactions */ + puhost->control.buf = buf; + puhost->control.ctl_len = len; + + puhost->control.ctl_state = CTL_SETUP; +} + +/*! + \brief get device descriptor from the USB device + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] len: length of the descriptor + \param[out] none + \retval operation status +*/ +usbh_status usbh_devdesc_get (usb_core_driver *pudev, usbh_host *puhost, uint8_t len) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_IN | USB_RECPTYPE_DEV | USB_REQTYPE_STRD, + .bRequest = USB_GET_DESCRIPTOR, + .wValue = USBH_DESC(USB_DESCTYPE_DEV), + .wIndex = 0U, + .wLength = len + }; + + usbh_ctlstate_config (puhost, pudev->host.rx_buf, len); + } + + status = usbh_ctl_handler (pudev, puhost); + + if (USBH_OK == status) { + /* commands successfully sent and response received */ + usbh_devdesc_parse (&puhost->dev_prop.dev_desc, pudev->host.rx_buf, len); + } + + return status; +} + +/*! + \brief get configuration descriptor from the USB device + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] len: length of the descriptor + \param[out] none + \retval operation status +*/ +usbh_status usbh_cfgdesc_get (usb_core_driver *pudev, usbh_host *puhost, uint16_t len) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_IN | USB_RECPTYPE_DEV | USB_REQTYPE_STRD, + .bRequest = USB_GET_DESCRIPTOR, + .wValue = USBH_DESC(USB_DESCTYPE_CONFIG), + .wIndex = 0U, + .wLength = len + }; + + usbh_ctlstate_config (puhost, pudev->host.rx_buf, len); + } + + status = usbh_ctl_handler (pudev, puhost); + + if (USBH_OK == status) { + if (len <= USB_CFG_DESC_LEN) { + usbh_cfgdesc_parse (&puhost->dev_prop.cfg_desc, pudev->host.rx_buf); + } else { + usbh_cfgset_parse (&puhost->dev_prop, pudev->host.rx_buf); + } + } + + return status; +} + +/*! + \brief get string descriptor from the USB device + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] str_index: index for the string descriptor + \param[in] buf: buffer pointer to the string descriptor + \param[in] len: length of the descriptor + \param[out] none + \retval operation status +*/ +usbh_status usbh_strdesc_get (usb_core_driver *pudev, + usbh_host *puhost, + uint8_t str_index, + uint8_t *buf, + uint16_t len) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_IN | USB_RECPTYPE_DEV | USB_REQTYPE_STRD, + .bRequest = USB_GET_DESCRIPTOR, + .wValue = USBH_DESC(USB_DESCTYPE_STR) | str_index, + .wIndex = 0x0409U, + .wLength = len + }; + + usbh_ctlstate_config (puhost, pudev->host.rx_buf, len); + } + + status = usbh_ctl_handler (pudev, puhost); + + if (USBH_OK == status) { + /* commands successfully sent and response received */ + usbh_strdesc_parse (pudev->host.rx_buf, buf, len); + } + + return status; +} + +/*! + \brief set the address to the connected device + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] dev_addr: device address to assign + \param[out] none + \retval operation status +*/ +usbh_status usbh_setaddress (usb_core_driver *pudev, usbh_host *puhost, uint8_t dev_addr) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_OUT | USB_RECPTYPE_DEV | USB_REQTYPE_STRD, + .bRequest = USB_SET_ADDRESS, + .wValue = (uint16_t)dev_addr, + .wIndex = 0U, + .wLength = 0U + }; + + usbh_ctlstate_config (puhost, NULL, 0U); + } + + status = usbh_ctl_handler (pudev, puhost); + + return status; +} + +/*! + \brief set the configuration value to the connected device + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] config_index: configuration value + \param[out] none + \retval operation status +*/ +usbh_status usbh_setcfg (usb_core_driver *pudev, usbh_host *puhost, uint16_t config_index) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_OUT | USB_RECPTYPE_DEV | USB_REQTYPE_STRD, + .bRequest = USB_SET_CONFIGURATION, + .wValue = config_index, + .wIndex = 0U, + .wLength = 0U + }; + + usbh_ctlstate_config (puhost, NULL, 0U); + } + + status = usbh_ctl_handler (pudev, puhost); + + return status; +} + +/*! + \brief set the interface value to the connected device + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] ep_num: endpoint number + \param[in] alter_setting: altnated setting value + \param[out] none + \retval operation status +*/ +usbh_status usbh_setinterface (usb_core_driver *pudev, + usbh_host *puhost, + uint8_t ep_num, + uint8_t set) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_OUT | USB_RECPTYPE_ITF | USB_REQTYPE_STRD, + .bRequest = USB_SET_INTERFACE, + .wValue = set, + .wIndex = ep_num, + .wLength = 0U + }; + + usbh_ctlstate_config (puhost, NULL, 0U); + } + + status = usbh_ctl_handler (pudev, puhost); + + return status; +} + +/*! + \brief clear or disable a specific feature + \param[in] pudev: pointer to usb core instance + \param[in] puhost: pointer to usb host + \param[in] ep_addr: endpoint address + \param[in] pp_num: pipe number + \param[out] none + \retval operation status +*/ +usbh_status usbh_clrfeature (usb_core_driver *pudev, + usbh_host *puhost, + uint8_t ep_addr, + uint8_t pp_num) +{ + usbh_status status = USBH_BUSY; + + usbh_control *usb_ctl = &puhost->control; + + if (CTL_IDLE == usb_ctl->ctl_state) { + usb_ctl->setup.req = (usb_req) { + .bmRequestType = USB_TRX_OUT | USB_RECPTYPE_EP | USB_REQTYPE_STRD, + .bRequest = USB_CLEAR_FEATURE, + .wValue = FEATURE_SELECTOR_EP, + .wIndex = ep_addr, + .wLength = 0 + }; + + if (EP_DIR(ep_addr)) { + pudev->host.pipe[pp_num].data_toggle_in = 0U; + } else { + pudev->host.pipe[pp_num].data_toggle_out = 0U; + } + + usbh_ctlstate_config (puhost, NULL, 0U); + } + + status = usbh_ctl_handler (pudev, puhost); + + return status; +} + +/*! + \brief parse the device descriptor + \param[in] dev_desc: pointer to usb device descriptor buffer + \param[in] buf: pointer to the source descriptor buffer + \param[in] len: length of the descriptor + \param[out] none + \retval operation status +*/ +static void usbh_devdesc_parse (usb_desc_dev *dev_desc, uint8_t *buf, uint16_t len) +{ + *dev_desc = (usb_desc_dev) { + .header = { + .bLength = *(uint8_t *)(buf + 0U), + .bDescriptorType = *(uint8_t *)(buf + 1U) + }, + + .bcdUSB = BYTE_SWAP(buf + 2U), + .bDeviceClass = *(uint8_t *)(buf + 4U), + .bDeviceSubClass = *(uint8_t *)(buf + 5U), + .bDeviceProtocol = *(uint8_t *)(buf + 6U), + .bMaxPacketSize0 = *(uint8_t *)(buf + 7U) + }; + + if (len > 8U) { + /* for 1st time after device connection, host may issue only 8 bytes for device descriptor length */ + dev_desc->idVendor = BYTE_SWAP(buf + 8U); + dev_desc->idProduct = BYTE_SWAP(buf + 10U); + dev_desc->bcdDevice = BYTE_SWAP(buf + 12U); + dev_desc->iManufacturer = *(uint8_t *)(buf + 14U); + dev_desc->iProduct = *(uint8_t *)(buf + 15U); + dev_desc->iSerialNumber = *(uint8_t *)(buf + 16U); + dev_desc->bNumberConfigurations = *(uint8_t *)(buf + 17U); + } +} + +/*! + \brief parse the configuration descriptor + \param[in] cfg_desc: pointer to usb configuration descriptor buffer + \param[in] buf: pointer to the source descriptor buffer + \param[out] none + \retval operation status +*/ +static void usbh_cfgdesc_parse (usb_desc_config *cfg_desc, uint8_t *buf) +{ + /* parse configuration descriptor */ + *cfg_desc = (usb_desc_config) { + .header = { + .bLength = *(uint8_t *)(buf + 0U), + .bDescriptorType = *(uint8_t *)(buf + 1U), + }, + + .wTotalLength = BYTE_SWAP(buf + 2U), + .bNumInterfaces = *(uint8_t *)(buf + 4U), + .bConfigurationValue = *(uint8_t *)(buf + 5U), + .iConfiguration = *(uint8_t *)(buf + 6U), + .bmAttributes = *(uint8_t *)(buf + 7U), + .bMaxPower = *(uint8_t *)(buf + 8U) + }; +} + +/*! + \brief parse the configuration descriptor set + \param[in] udev: pointer to USB core instance + \param[in] buf: pointer to the source descriptor buffer + \param[out] none + \retval operation status +*/ +static void usbh_cfgset_parse (usb_dev_prop *udev, uint8_t *buf) +{ + usb_desc_ep *ep = NULL; + usb_desc_itf *itf = NULL, itf_value; + + usb_desc_header *pdesc = (usb_desc_header *)buf; + + int8_t itf_index = 0U, ep_index = 0U; + uint16_t ptr; + + uint8_t prev_itf = 0U; + uint16_t prev_ep_len = 0U; + + /* parse configuration descriptor */ + usbh_cfgdesc_parse (&udev->cfg_desc, buf); + + ptr = USB_CFG_DESC_LEN; + + if (udev->cfg_desc.bNumInterfaces > USBH_MAX_INTERFACES_NUM) { + return; + } + + while (ptr < udev->cfg_desc.wTotalLength) { + pdesc = usbh_nextdesc_get ((uint8_t *)pdesc, &ptr); + + if (pdesc->bDescriptorType == USB_DESCTYPE_ITF) { + itf_index = *(((uint8_t *)pdesc) + 2U); + itf = &udev->itf_desc[itf_index]; + + if ((*((uint8_t *)pdesc + 3U)) < 3U) { + usbh_itfdesc_parse (&itf_value, (uint8_t *)pdesc); + + /* parse endpoint descriptors relative to the current interface */ + if (itf_value.bNumEndpoints > USBH_MAX_EP_NUM) { + return; + } + + for (ep_index = 0; ep_index < itf_value.bNumEndpoints; ) { + pdesc = usbh_nextdesc_get ((void*)pdesc, &ptr); + + if (pdesc->bDescriptorType == USB_DESCTYPE_EP) { + ep = &udev->ep_desc[itf_index][ep_index]; + + if (prev_itf != itf_index) { + prev_itf = itf_index; + usbh_itfdesc_parse (itf, (uint8_t *)&itf_value); + } else { + if (prev_ep_len > BYTE_SWAP((uint8_t *)pdesc + 4U)) { + break; + } else { + usbh_itfdesc_parse (itf, (uint8_t *)&itf_value); + } + } + + usbh_epdesc_parse (ep, (uint8_t *)pdesc); + prev_ep_len = BYTE_SWAP((uint8_t *)pdesc + 4U); + ep_index++; + } + } + } + } + } +} + +/*! + \brief parse the interface descriptor + \param[in] itf_desc: pointer to usb interface descriptor buffer + \param[in] buf: pointer to the source descriptor buffer + \param[out] none + \retval operation status +*/ +static void usbh_itfdesc_parse (usb_desc_itf *itf_desc, uint8_t *buf) +{ + *itf_desc = (usb_desc_itf) { + .header = { + .bLength = *(uint8_t *)(buf + 0U), + .bDescriptorType = *(uint8_t *)(buf + 1U), + }, + + .bInterfaceNumber = *(uint8_t *)(buf + 2U), + .bAlternateSetting = *(uint8_t *)(buf + 3U), + .bNumEndpoints = *(uint8_t *)(buf + 4U), + .bInterfaceClass = *(uint8_t *)(buf + 5U), + .bInterfaceSubClass = *(uint8_t *)(buf + 6U), + .bInterfaceProtocol = *(uint8_t *)(buf + 7U), + .iInterface = *(uint8_t *)(buf + 8U) + }; +} + +/*! + \brief parse the endpoint descriptor + \param[in] ep_desc: pointer to usb endpoint descriptor buffer + \param[in] buf: pointer to the source descriptor buffer + \param[out] none + \retval operation status +*/ +static void usbh_epdesc_parse (usb_desc_ep *ep_desc, uint8_t *buf) +{ + *ep_desc = (usb_desc_ep) { + .header = { + .bLength = *(uint8_t *)(buf + 0U), + .bDescriptorType = *(uint8_t *)(buf + 1U) + }, + + .bEndpointAddress = *(uint8_t *)(buf + 2U), + .bmAttributes = *(uint8_t *)(buf + 3U), + .wMaxPacketSize = BYTE_SWAP(buf + 4U), + .bInterval = *(uint8_t *)(buf + 6U) + }; +} + +/*! + \brief parse the string descriptor + \param[in] psrc: source pointer containing the descriptor data + \param[in] pdest: destination address pointer + \param[in] len: length of the descriptor + \param[out] none + \retval operation status +*/ +static void usbh_strdesc_parse (uint8_t *psrc, uint8_t *pdest, uint16_t len) +{ + uint16_t str_len = 0U, index = 0U; + + /* the unicode string descriptor is not NULL-terminated. The string length is + * computed by substracting two from the value of the first byte of the descriptor. + */ + + /* check which is lower size, the size of string or the length of bytes read from the device */ + if (USB_DESCTYPE_STR == psrc[1]) { + /* make sure the descriptor is string type */ + + /* psrc[0] contains Size of Descriptor, subtract 2 to get the length of string */ + str_len = USB_MIN(psrc[0] - 2U, len); + + psrc += 2U; /* adjust the offset ignoring the string len and descriptor type */ + + for (index = 0U; index < str_len; index += 2U) { + /* copy only the string and ignore the unicode id, hence add the src */ + *pdest = psrc[index]; + + pdest++; + } + + *pdest = 0U; /* mark end of string */ + } +} + +/*! + \brief get the next descriptor header + \param[in] pbuf: pointer to buffer where the configuration descriptor set is available + \param[in] ptr: data popinter inside the configuration descriptor set + \param[out] none + \retval operation status +*/ +usb_desc_header *usbh_nextdesc_get (uint8_t *pbuf, uint16_t *ptr) +{ + usb_desc_header *pnext; + + *ptr += ((usb_desc_header *)pbuf)->bLength; + + pnext = (usb_desc_header *)((uint8_t *)pbuf + ((usb_desc_header *)pbuf)->bLength); + + return (pnext); +} + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_pipe.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_pipe.c new file mode 100644 index 00000000..8ff45e0d --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_pipe.c @@ -0,0 +1,174 @@ +/*! + \file usbh_pipe.c + \brief USB host mode pipe operation driver + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "usbh_pipe.h" + +static uint16_t usbh_freepipe_get (usb_core_driver *pudev); + +/*! + \brief create a pipe + \param[in] pudev: pointer to usb core instance + \param[in] pp_num: pipe number + \param[in] udev: USB device + \param[in] ep_type: endpoint type + \param[in] ep_mpl: endpoint max packet length + \param[out] none + \retval operation status +*/ +uint8_t usbh_pipe_create (usb_core_driver *pudev, + usb_dev_prop *udev, + uint8_t pp_num, + uint8_t ep_type, + uint16_t ep_mpl) +{ + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + pp->dev_addr = udev->addr; + pp->dev_speed = udev->speed; + pp->ep.type = ep_type; + pp->ep.mps = ep_mpl; + pp->ping = udev->speed == PORT_SPEED_HIGH; + + usb_pipe_init (pudev, pp_num); + + return HC_OK; +} + +/*! + \brief modify a pipe + \param[in] pudev: pointer to usb core instance + \param[in] pp_num: pipe number + \param[in] dev_addr: device address + \param[in] dev_speed: device speed + \param[in] ep_type: endpoint type + \param[in] ep_mpl: endpoint max packet length + \param[out] none + \retval operation status +*/ +uint8_t usbh_pipe_update (usb_core_driver *pudev, + uint8_t pp_num, + uint8_t dev_addr, + uint32_t dev_speed, + uint16_t ep_mpl) +{ + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + if ((pp->dev_addr != dev_addr) && (dev_addr)) { + pp->dev_addr = dev_addr; + } + + if ((pp->dev_speed != dev_speed) && (dev_speed)) { + pp->dev_speed = dev_speed; + } + + if ((pp->ep.mps != ep_mpl) && (ep_mpl)) { + pp->ep.mps = ep_mpl; + } + + usb_pipe_init (pudev, pp_num); + + return HC_OK; +} + +/*! + \brief allocate a new pipe + \param[in] pudev: pointer to usb core instance + \param[in] ep_addr: endpoint address + \param[out] none + \retval operation status +*/ +uint8_t usbh_pipe_allocate (usb_core_driver *pudev, uint8_t ep_addr) +{ + uint16_t pp_num = usbh_freepipe_get (pudev); + + if (HC_ERROR != pp_num) { + pudev->host.pipe[pp_num].in_used = 1U; + pudev->host.pipe[pp_num].ep.dir = EP_DIR(ep_addr); + pudev->host.pipe[pp_num].ep.num = EP_ID(ep_addr); + } + + return pp_num; +} + +/*! + \brief free a pipe + \param[in] pudev: pointer to usb core instance + \param[in] pp_num: pipe number + \param[out] none + \retval operation status +*/ +uint8_t usbh_pipe_free (usb_core_driver *pudev, uint8_t pp_num) +{ + if (pp_num < HC_MAX) { + pudev->host.pipe[pp_num].in_used = 0U; + } + + return USBH_OK; +} + +/*! + \brief delete all USB host pipe + \param[in] pudev: pointer to usb core instance + \param[out] none + \retval operation status +*/ +uint8_t usbh_pipe_delete (usb_core_driver *pudev) +{ + uint8_t pp_num = 0U; + + for (pp_num = 2U; pp_num < HC_MAX; pp_num++) { + pudev->host.pipe[pp_num] = (usb_pipe) {0}; + } + + return USBH_OK; +} + +/*! + \brief get a free pipe number for allocation + \param[in] pudev: pointer to usb core instance + \param[out] none + \retval operation status +*/ +static uint16_t usbh_freepipe_get (usb_core_driver *pudev) +{ + uint8_t pp_num = 0U; + + for (pp_num = 0U; pp_num < HC_MAX; pp_num++) { + if (pudev->host.pipe[pp_num].in_used == 0U) { + return pp_num; + } + } + + return HC_ERROR; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_transc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_transc.c new file mode 100644 index 00000000..b1f8cc9b --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/Usb/usbh_transc.c @@ -0,0 +1,391 @@ +/*! + \file usbh_transc.c + \brief USB host mode transactions driver + + \version 2019-6-5, V1.0.0, firmware for GD32 USBFS&USBHS +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "drv_usb_hw.h" +#include "usbh_transc.h" + +/*! + \brief prepare a pipe and start a transfer + \param[in] pudev: pointer to usb core instance + \param[in] pp_num: pipe number + \param[out] none + \retval operation status +*/ +static uint32_t usbh_request_submit (usb_core_driver *pudev, uint8_t pp_num) +{ + pudev->host.pipe[pp_num].urb_state = URB_IDLE; + pudev->host.pipe[pp_num].xfer_count = 0U; + + return usb_pipe_xfer (pudev, pp_num); +} + +/*! + \brief send the setup packet to the USB device + \param[in] pudev: pointer to usb core instance + \param[in] buf: data buffer which will be sent to USB device + \param[in] pp_num: pipe number + \param[out] none + \retval operation status +*/ +usbh_status usbh_ctlsetup_send (usb_core_driver *pudev, uint8_t *buf, uint8_t pp_num) +{ + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + pp->DPID = PIPE_DPID_SETUP; + pp->xfer_buf = buf; + pp->xfer_len = USB_SETUP_PACKET_LEN; + + return (usbh_status)usbh_request_submit (pudev, pp_num); +} + +/*! + \brief send a data packet to the USB device + \param[in] pudev: pointer to usb core instance + \param[in] buf: data buffer which will be sent to USB device + \param[in] pp_num: pipe number + \param[in] len: length of the data to be sent + \param[out] none + \retval operation status +*/ +usbh_status usbh_data_send (usb_core_driver *pudev, uint8_t *buf, uint8_t pp_num, uint16_t len) +{ + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + pp->xfer_buf = buf; + pp->xfer_len = len; + + switch (pp->ep.type) { + case USB_EPTYPE_CTRL: + if (0U == len) { + pp->data_toggle_out = 1U; + } + + pp->DPID = PIPE_DPID[pp->data_toggle_out]; + break; + + case USB_EPTYPE_INTR: + pp->DPID = PIPE_DPID[pp->data_toggle_out]; + + pp->data_toggle_out ^= 1U; + break; + + case USB_EPTYPE_BULK: + pp->DPID = PIPE_DPID[pp->data_toggle_out]; + break; + + case USB_EPTYPE_ISOC: + pp->DPID = PIPE_DPID[0]; + break; + + default: + break; + } + + usbh_request_submit (pudev, pp_num); + + return USBH_OK; +} + +/*! + \brief receive a data packet from the USB device + \param[in] pudev: pointer to usb core instance + \param[in] buf: data buffer which will be received from USB device + \param[in] pp_num: pipe number + \param[in] len: length of the data to be received + \param[out] none + \retval operation status +*/ +usbh_status usbh_data_recev (usb_core_driver *pudev, uint8_t *buf, uint8_t pp_num, uint16_t len) +{ + usb_pipe *pp = &pudev->host.pipe[pp_num]; + + pp->xfer_buf = buf; + pp->xfer_len = len; + + switch (pp->ep.type) { + case USB_EPTYPE_CTRL: + pp->DPID = PIPE_DPID[1]; + break; + + case USB_EPTYPE_INTR: + pp->DPID = PIPE_DPID[pp->data_toggle_in]; + + /* Toggle DATA PID */ + pp->data_toggle_in ^= 1U; + break; + + case USB_EPTYPE_BULK: + pp->DPID = PIPE_DPID[pp->data_toggle_in]; + break; + + case USB_EPTYPE_ISOC: + pp->DPID = PIPE_DPID[0]; + break; + + default: + break; + } + + usbh_request_submit (pudev, pp_num); + + return USBH_OK; +} + +/*! + \brief wait for USB URB(USB request block) state + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[in] pp_num: pipe number + \param[in] wait_time: wait time + \param[out] none + \retval USB URB state +*/ +static usb_urb_state usbh_urb_wait (usb_core_driver *pudev, usbh_host *puhost, uint8_t pp_num, uint32_t wait_time) +{ + usb_urb_state urb_status = URB_IDLE; + + while (URB_DONE != (urb_status = usbh_urbstate_get(pudev, pp_num))) { + if (URB_NOTREADY == urb_status) { + break; + } else if (URB_STALL == urb_status) { + puhost->control.ctl_state = CTL_SETUP; + break; + } else if (URB_ERROR == urb_status) { + puhost->control.ctl_state = CTL_ERROR; + break; + } else if ((wait_time > 0U) && \ + ((usb_curframe_get(pudev)- puhost->control.timer) > wait_time)) { + /* timeout for in transfer */ + puhost->control.ctl_state = CTL_ERROR; + break; + } else { + /* no operation, just wait */ + } + } + + return urb_status; +} + +/*! + \brief USB setup transaction + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval none +*/ +static void usbh_setup_transc (usb_core_driver *pudev, usbh_host *puhost) +{ + usb_urb_state urb_status = URB_IDLE; + + /* send a SETUP packet */ + usbh_ctlsetup_send (pudev, + puhost->control.setup.data, + puhost->control.pipe_out_num); + + urb_status = usbh_urb_wait (pudev, puhost, puhost->control.pipe_out_num, 0U); + + if (URB_DONE == urb_status) { + uint8_t dir = (puhost->control.setup.req.bmRequestType & USB_TRX_MASK); + + if (puhost->control.setup.req.wLength) { + if (USB_TRX_IN == dir) { + puhost->control.ctl_state = CTL_DATA_IN; + } else { + puhost->control.ctl_state = CTL_DATA_OUT; + } + } else { + if (USB_TRX_IN == dir) { + puhost->control.ctl_state = CTL_STATUS_OUT; + } else { + puhost->control.ctl_state = CTL_STATUS_IN; + } + } + + /* set the delay timer to enable timeout for data stage completion */ + puhost->control.timer = usb_curframe_get(pudev); + } +} + +/*! + \brief USB data IN transaction + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval none +*/ +static void usbh_data_in_transc (usb_core_driver *pudev, usbh_host *puhost) +{ + usb_urb_state urb_status = URB_IDLE; + + usbh_data_recev (pudev, + puhost->control.buf, + puhost->control.pipe_in_num, + puhost->control.ctl_len); + + urb_status = usbh_urb_wait (pudev, puhost, puhost->control.pipe_in_num, DATA_STAGE_TIMEOUT); + + if (URB_DONE == urb_status) { + puhost->control.ctl_state = CTL_STATUS_OUT; + + puhost->control.timer = usb_curframe_get(pudev); + } +} + +/*! + \brief USB data OUT transaction + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval none +*/ +static void usbh_data_out_transc (usb_core_driver *pudev, usbh_host *puhost) +{ + usb_urb_state urb_status = URB_IDLE; + + pudev->host.pipe[puhost->control.pipe_out_num].data_toggle_out = 1U; + + usbh_data_send (pudev, + puhost->control.buf, + puhost->control.pipe_out_num, + puhost->control.ctl_len); + + urb_status = usbh_urb_wait (pudev, puhost, puhost->control.pipe_out_num, DATA_STAGE_TIMEOUT); + + if (URB_DONE == urb_status) { + puhost->control.ctl_state = CTL_STATUS_IN; + + puhost->control.timer = usb_curframe_get(pudev); + } +} + +/*! + \brief USB status IN transaction + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval none +*/ +static void usbh_status_in_transc (usb_core_driver *pudev, usbh_host *puhost) +{ + uint8_t pp_num = puhost->control.pipe_in_num; + + usb_urb_state urb_status = URB_IDLE; + + usbh_data_recev (pudev, NULL, pp_num, 0U); + + urb_status = usbh_urb_wait (pudev, puhost, pp_num, NODATA_STAGE_TIMEOUT); + + if (URB_DONE == urb_status) { + puhost->control.ctl_state = CTL_FINISH; + } +} + +/*! + \brief USB status OUT transaction + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval none +*/ +static void usbh_status_out_transc (usb_core_driver *pudev, usbh_host *puhost) +{ + uint8_t pp_num = puhost->control.pipe_out_num; + + usb_urb_state urb_status = URB_IDLE; + + pudev->host.pipe[pp_num].data_toggle_out ^= 1U; + + usbh_data_send (pudev, NULL, pp_num, 0U); + + urb_status = usbh_urb_wait (pudev, puhost, pp_num, NODATA_STAGE_TIMEOUT); + + if (URB_DONE == urb_status) { + puhost->control.ctl_state = CTL_FINISH; + } +} + +/*! + \brief USB control transfer handler + \param[in] pudev: pointer to USB core instance + \param[in] puhost: pointer to USB host + \param[out] none + \retval operation status +*/ +usbh_status usbh_ctl_handler (usb_core_driver *pudev, usbh_host *puhost) +{ + usbh_status status = USBH_BUSY; + + switch (puhost->control.ctl_state) { + case CTL_SETUP: + usbh_setup_transc (pudev, puhost); + break; + + case CTL_DATA_IN: + usbh_data_in_transc (pudev, puhost); + break; + + case CTL_DATA_OUT: + usbh_data_out_transc (pudev, puhost); + break; + + case CTL_STATUS_IN: + usbh_status_in_transc (pudev, puhost); + break; + + case CTL_STATUS_OUT: + usbh_status_out_transc (pudev, puhost); + break; + + case CTL_FINISH: + puhost->control.ctl_state = CTL_IDLE; + + status = USBH_OK; + break; + + case CTL_ERROR: + if (++puhost->control.error_count <= USBH_MAX_ERROR_COUNT) { + /* do the transmission again, starting from SETUP packet */ + puhost->control.ctl_state = CTL_SETUP; + } else { + status = USBH_FAIL; + } + break; + + default: + break; + } + + return status; +} + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_adc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_adc.c new file mode 100644 index 00000000..d4aa407d --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_adc.c @@ -0,0 +1,994 @@ +/*! + \file gd32vf103_adc.c + \brief ADC driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_adc.h" +#include "gd32vf103_rcu.h" + +/* discontinuous mode macro*/ +#define ADC_CHANNEL_LENGTH_SUBTRACT_ONE ((uint8_t)1U) + +/* ADC regular channel macro */ +#define ADC_REGULAR_CHANNEL_RANK_SIX ((uint8_t)6U) +#define ADC_REGULAR_CHANNEL_RANK_TWELVE ((uint8_t)12U) +#define ADC_REGULAR_CHANNEL_RANK_SIXTEEN ((uint8_t)16U) +#define ADC_REGULAR_CHANNEL_RANK_LENGTH ((uint8_t)5U) + +/* ADC sampling time macro */ +#define ADC_CHANNEL_SAMPLE_TEN ((uint8_t)10U) +#define ADC_CHANNEL_SAMPLE_EIGHTEEN ((uint8_t)18U) +#define ADC_CHANNEL_SAMPLE_LENGTH ((uint8_t)3U) + +/* ADC inserted channel macro */ +#define ADC_INSERTED_CHANNEL_RANK_LENGTH ((uint8_t)5U) +#define ADC_INSERTED_CHANNEL_SHIFT_LENGTH ((uint8_t)15U) + +/* ADC inserted channel offset macro */ +#define ADC_OFFSET_LENGTH ((uint8_t)3U) +#define ADC_OFFSET_SHIFT_LENGTH ((uint8_t)4U) + +/*! + \brief reset ADC + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_deinit(uint32_t adc_periph) +{ + switch(adc_periph){ + case ADC0: + /* reset ADC0 */ + rcu_periph_reset_enable(RCU_ADC0RST); + rcu_periph_reset_disable(RCU_ADC0RST); + break; + case ADC1: + /* reset ADC1 */ + rcu_periph_reset_enable(RCU_ADC1RST); + rcu_periph_reset_disable(RCU_ADC1RST); + break; + default: + break; + } +} + +/*! + \brief configure the ADC sync mode + \param[in] adc_periph: ADCx, x=0,1 + \param[in] mode: ADC mode + only one parameter can be selected which is shown as below: + \arg ADC_MODE_FREE: all the ADCs work independently + \arg ADC_DAUL_REGULAL_PARALLEL_INSERTED_PARALLEL: ADC0 and ADC1 work in combined regular parallel + inserted parallel mode + \arg ADC_DAUL_REGULAL_PARALLEL_INSERTED_ROTATION: ADC0 and ADC1 work in combined regular parallel + trigger rotation mode + \arg ADC_DAUL_INSERTED_PARALLEL_REGULAL_FOLLOWUP_FAST: ADC0 and ADC1 work in combined inserted parallel + follow-up fast mode + \arg ADC_DAUL_INSERTED_PARALLEL_REGULAL_FOLLOWUP_SLOW: ADC0 and ADC1 work in combined inserted parallel + follow-up slow mode + \arg ADC_DAUL_INSERTED_PARALLEL: ADC0 and ADC1 work in inserted parallel mode only + \arg ADC_DAUL_REGULAL_PARALLEL: ADC0 and ADC1 work in regular parallel mode only + \arg ADC_DAUL_REGULAL_FOLLOWUP_FAST: ADC0 and ADC1 work in follow-up fast mode only + \arg ADC_DAUL_REGULAL_FOLLOWUP_SLOW: ADC0 and ADC1 work in follow-up slow mode only + \arg ADC_DAUL_INSERTED_TRIGGER_ROTATION: ADC0 and ADC1 work in trigger rotation mode only + \param[out] none + \retval none +*/ +void adc_mode_config(uint32_t adc_periph, uint32_t mode) +{ + ADC_CTL0(adc_periph) &= ~(ADC_CTL0_SYNCM); + ADC_CTL0(adc_periph) |= mode; +} + +/*! + \brief enable or disable ADC special function + \param[in] adc_periph: ADCx, x=0,1 + \param[in] function: the function to config + only one parameter can be selected which is shown as below: + \arg ADC_SCAN_MODE: scan mode select + \arg ADC_INSERTED_CHANNEL_AUTO: inserted channel group convert automatically + \arg ADC_CONTINUOUS_MODE: continuous mode select + \param[in] newvalue: ENABLE or DISABLE + \param[out] none + \retval none +*/ +void adc_special_function_config(uint32_t adc_periph, uint32_t function, ControlStatus newvalue) +{ + if(newvalue){ + if(0U != (function & ADC_SCAN_MODE)){ + /* enable scan mode */ + ADC_CTL0(adc_periph) |= ADC_SCAN_MODE; + } + if(0U != (function & ADC_INSERTED_CHANNEL_AUTO)){ + /* enable inserted channel group convert automatically */ + ADC_CTL0(adc_periph) |= ADC_INSERTED_CHANNEL_AUTO; + } + if(0U != (function & ADC_CONTINUOUS_MODE)){ + /* enable continuous mode */ + ADC_CTL1(adc_periph) |= ADC_CONTINUOUS_MODE; + } + }else{ + if(0U != (function & ADC_SCAN_MODE)){ + /* disable scan mode */ + ADC_CTL0(adc_periph) &= ~ADC_SCAN_MODE; + } + if(0U != (function & ADC_INSERTED_CHANNEL_AUTO)){ + /* disable inserted channel group convert automatically */ + ADC_CTL0(adc_periph) &= ~ADC_INSERTED_CHANNEL_AUTO; + } + if(0U != (function & ADC_CONTINUOUS_MODE)){ + /* disable continuous mode */ + ADC_CTL1(adc_periph) &= ~ADC_CONTINUOUS_MODE; + } + } +} + +/*! + \brief configure ADC data alignment + \param[in] adc_periph: ADCx, x=0,1 + \param[in] data_alignment: data alignment select + only one parameter can be selected which is shown as below: + \arg ADC_DATAALIGN_RIGHT: LSB alignment + \arg ADC_DATAALIGN_LEFT: MSB alignment + \param[out] none + \retval none +*/ +void adc_data_alignment_config(uint32_t adc_periph, uint32_t data_alignment) +{ + if(ADC_DATAALIGN_RIGHT != data_alignment){ + /* MSB alignment */ + ADC_CTL1(adc_periph) |= ADC_CTL1_DAL; + }else{ + /* LSB alignment */ + ADC_CTL1(adc_periph) &= ~((uint32_t)ADC_CTL1_DAL); + } +} + +/*! + \brief enable ADC interface + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_enable(uint32_t adc_periph) +{ + if(RESET == (ADC_CTL1(adc_periph) & ADC_CTL1_ADCON)){ + /* enable ADC */ + ADC_CTL1(adc_periph) |= (uint32_t)ADC_CTL1_ADCON; + } +} + +/*! + \brief disable ADC interface + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_disable(uint32_t adc_periph) +{ + /* disable ADC */ + ADC_CTL1(adc_periph) &= ~((uint32_t)ADC_CTL1_ADCON); +} + +/*! + \brief ADC calibration and reset calibration + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_calibration_enable(uint32_t adc_periph) +{ + /* reset the selected ADC1 calibration registers */ + ADC_CTL1(adc_periph) |= (uint32_t) ADC_CTL1_RSTCLB; + /* check the RSTCLB bit state */ + while(RESET != (ADC_CTL1(adc_periph) & ADC_CTL1_RSTCLB)){ + } + /* enable ADC calibration process */ + ADC_CTL1(adc_periph) |= ADC_CTL1_CLB; + /* check the CLB bit state */ + while(RESET != (ADC_CTL1(adc_periph) & ADC_CTL1_CLB)){ + } +} + +/*! + \brief enable the temperature sensor and Vrefint channel + \param[in] none + \param[out] none + \retval none +*/ +void adc_tempsensor_vrefint_enable(void) +{ + /* enable the temperature sensor and Vrefint channel */ + ADC_CTL1(ADC0) |= ADC_CTL1_TSVREN; +} + +/*! + \brief disable the temperature sensor and Vrefint channel + \param[in] none + \param[out] none + \retval none +*/ +void adc_tempsensor_vrefint_disable(void) +{ + /* disable the temperature sensor and Vrefint channel */ + ADC_CTL1(ADC0) &= ~ADC_CTL1_TSVREN; +} + +/*! + \brief enable DMA request + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_dma_mode_enable(uint32_t adc_periph) +{ + /* enable DMA request */ + ADC_CTL1(adc_periph) |= (uint32_t)(ADC_CTL1_DMA); +} + +/*! + \brief disable DMA request + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_dma_mode_disable(uint32_t adc_periph) +{ + /* disable DMA request */ + ADC_CTL1(adc_periph) &= ~((uint32_t)ADC_CTL1_DMA); +} + +/*! + \brief configure ADC discontinuous mode + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel_group: select the channel group + only one parameter can be selected which is shown as below: + \arg ADC_REGULAR_CHANNEL: regular channel group + \arg ADC_INSERTED_CHANNEL: inserted channel group + \arg ADC_CHANNEL_DISCON_DISABLE: disable discontinuous mode of regular & inserted channel + \param[in] length: number of conversions in discontinuous mode,the number can be 1..8 + for regular channel, the number has no effect for inserted channel + \param[out] none + \retval none +*/ +void adc_discontinuous_mode_config(uint32_t adc_periph, uint8_t adc_channel_group, uint8_t length) +{ + /* disable discontinuous mode of regular & inserted channel */ + ADC_CTL0(adc_periph) &= ~((uint32_t)(ADC_CTL0_DISRC | ADC_CTL0_DISIC)); + switch(adc_channel_group){ + case ADC_REGULAR_CHANNEL: + /* config the number of conversions in discontinuous mode */ + ADC_CTL0(adc_periph) &= ~((uint32_t)ADC_CTL0_DISNUM); + ADC_CTL0(adc_periph) |= CTL0_DISNUM(((uint32_t)length - ADC_CHANNEL_LENGTH_SUBTRACT_ONE)); + /* enable regular channel group discontinuous mode */ + ADC_CTL0(adc_periph) |= (uint32_t)ADC_CTL0_DISRC; + break; + case ADC_INSERTED_CHANNEL: + /* enable inserted channel group discontinuous mode */ + ADC_CTL0(adc_periph) |= (uint32_t)ADC_CTL0_DISIC; + break; + case ADC_CHANNEL_DISCON_DISABLE: + /* disable discontinuous mode of regular & inserted channel */ + default: + break; + } +} + +/*! + \brief configure the length of regular channel group or inserted channel group + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel_group: select the channel group + only one parameter can be selected which is shown as below: + \arg ADC_REGULAR_CHANNEL: regular channel group + \arg ADC_INSERTED_CHANNEL: inserted channel group + \param[in] length: the length of the channel + regular channel 1-16 + inserted channel 1-4 + \param[out] none + \retval none +*/ +void adc_channel_length_config(uint32_t adc_periph, uint8_t adc_channel_group, uint32_t length) +{ + switch(adc_channel_group){ + case ADC_REGULAR_CHANNEL: + /* configure the length of regular channel group */ + ADC_RSQ0(adc_periph) &= ~((uint32_t)ADC_RSQ0_RL); + ADC_RSQ0(adc_periph) |= RSQ0_RL((uint32_t)(length-ADC_CHANNEL_LENGTH_SUBTRACT_ONE)); + break; + case ADC_INSERTED_CHANNEL: + /* configure the length of inserted channel group */ + ADC_ISQ(adc_periph) &= ~((uint32_t)ADC_ISQ_IL); + ADC_ISQ(adc_periph) |= ISQ_IL((uint32_t)(length-ADC_CHANNEL_LENGTH_SUBTRACT_ONE)); + break; + default: + break; + } +} + +/*! + \brief configure ADC regular channel + \param[in] adc_periph: ADCx, x=0,1 + \param[in] rank: the regular group sequence rank,this parameter must be between 0 to 15 + \param[in] adc_channel: the selected ADC channel + only one parameter can be selected which is shown as below: + \arg ADC_CHANNEL_x(x=0..17)(x=16 and x=17 are only for ADC0): ADC Channelx + \param[in] sample_time: the sample time value + only one parameter can be selected which is shown as below: + \arg ADC_SAMPLETIME_1POINT5: 1.5 cycles + \arg ADC_SAMPLETIME_7POINT5: 7.5 cycles + \arg ADC_SAMPLETIME_13POINT5: 13.5 cycles + \arg ADC_SAMPLETIME_28POINT5: 28.5 cycles + \arg ADC_SAMPLETIME_41POINT5: 41.5 cycles + \arg ADC_SAMPLETIME_55POINT5: 55.5 cycles + \arg ADC_SAMPLETIME_71POINT5: 71.5 cycles + \arg ADC_SAMPLETIME_239POINT5: 239.5 cycles + \param[out] none + \retval none +*/ +void adc_regular_channel_config(uint32_t adc_periph, uint8_t rank, uint8_t adc_channel, uint32_t sample_time) +{ + uint32_t rsq,sampt; + + /* ADC regular sequence config */ + if(rank < ADC_REGULAR_CHANNEL_RANK_SIX){ + /* the regular group sequence rank is smaller than six */ + rsq = ADC_RSQ2(adc_periph); + rsq &= ~((uint32_t)(ADC_RSQX_RSQN << (ADC_REGULAR_CHANNEL_RANK_LENGTH*rank))); + /* the channel number is written to these bits to select a channel as the nth conversion in the regular channel group */ + rsq |= ((uint32_t)adc_channel << (ADC_REGULAR_CHANNEL_RANK_LENGTH*rank)); + ADC_RSQ2(adc_periph) = rsq; + }else if(rank < ADC_REGULAR_CHANNEL_RANK_TWELVE){ + /* the regular group sequence rank is smaller than twelve */ + rsq = ADC_RSQ1(adc_periph); + rsq &= ~((uint32_t)(ADC_RSQX_RSQN << (ADC_REGULAR_CHANNEL_RANK_LENGTH*(rank-ADC_REGULAR_CHANNEL_RANK_SIX)))); + /* the channel number is written to these bits to select a channel as the nth conversion in the regular channel group */ + rsq |= ((uint32_t)adc_channel << (ADC_REGULAR_CHANNEL_RANK_LENGTH*(rank-ADC_REGULAR_CHANNEL_RANK_SIX))); + ADC_RSQ1(adc_periph) = rsq; + }else if(rank < ADC_REGULAR_CHANNEL_RANK_SIXTEEN){ + /* the regular group sequence rank is smaller than sixteen */ + rsq = ADC_RSQ0(adc_periph); + rsq &= ~((uint32_t)(ADC_RSQX_RSQN << (ADC_REGULAR_CHANNEL_RANK_LENGTH*(rank-ADC_REGULAR_CHANNEL_RANK_TWELVE)))); + /* the channel number is written to these bits to select a channel as the nth conversion in the regular channel group */ + rsq |= ((uint32_t)adc_channel << (ADC_REGULAR_CHANNEL_RANK_LENGTH*(rank-ADC_REGULAR_CHANNEL_RANK_TWELVE))); + ADC_RSQ0(adc_periph) = rsq; + }else{ + } + + /* ADC sampling time config */ + if(adc_channel < ADC_CHANNEL_SAMPLE_TEN){ + /* the regular group sequence rank is smaller than ten */ + sampt = ADC_SAMPT1(adc_periph); + sampt &= ~((uint32_t)(ADC_SAMPTX_SPTN << (ADC_CHANNEL_SAMPLE_LENGTH*adc_channel))); + /* channel sample time set*/ + sampt |= (uint32_t)(sample_time << (ADC_CHANNEL_SAMPLE_LENGTH*adc_channel)); + ADC_SAMPT1(adc_periph) = sampt; + }else if(adc_channel < ADC_CHANNEL_SAMPLE_EIGHTEEN){ + /* the regular group sequence rank is smaller than eighteen */ + sampt = ADC_SAMPT0(adc_periph); + sampt &= ~((uint32_t)(ADC_SAMPTX_SPTN << (ADC_CHANNEL_SAMPLE_LENGTH*(adc_channel-ADC_CHANNEL_SAMPLE_TEN)))); + /* channel sample time set*/ + sampt |= (uint32_t)(sample_time << (ADC_CHANNEL_SAMPLE_LENGTH*(adc_channel-ADC_CHANNEL_SAMPLE_TEN))); + ADC_SAMPT0(adc_periph) = sampt; + }else{ + } +} + +/*! + \brief configure ADC inserted channel + \param[in] adc_periph: ADCx, x=0,1 + \param[in] rank: the inserted group sequencer rank,this parameter must be between 0 to 3 + \param[in] adc_channel: the selected ADC channel + only one parameter can be selected which is shown as below: + \arg ADC_CHANNEL_x(x=0..17)(x=16 and x=17 are only for ADC0): ADC Channelx + \param[in] sample_time: The sample time value + only one parameter can be selected which is shown as below: + \arg ADC_SAMPLETIME_1POINT5: 1.5 cycles + \arg ADC_SAMPLETIME_7POINT5: 7.5 cycles + \arg ADC_SAMPLETIME_13POINT5: 13.5 cycles + \arg ADC_SAMPLETIME_28POINT5: 28.5 cycles + \arg ADC_SAMPLETIME_41POINT5: 41.5 cycles + \arg ADC_SAMPLETIME_55POINT5: 55.5 cycles + \arg ADC_SAMPLETIME_71POINT5: 71.5 cycles + \arg ADC_SAMPLETIME_239POINT5: 239.5 cycles + \param[out] none + \retval none +*/ +void adc_inserted_channel_config(uint32_t adc_periph, uint8_t rank, uint8_t adc_channel, uint32_t sample_time) +{ + uint8_t inserted_length; + uint32_t isq,sampt; + /* get inserted channel group length */ + inserted_length = (uint8_t)GET_BITS(ADC_ISQ(adc_periph) , 20U , 21U); + /* the channel number is written to these bits to select a channel as the nth conversion in the inserted channel group */ + isq = ADC_ISQ(adc_periph); + isq &= ~((uint32_t)(ADC_ISQ_ISQN << (ADC_INSERTED_CHANNEL_SHIFT_LENGTH-(inserted_length-rank)*ADC_INSERTED_CHANNEL_RANK_LENGTH))); + isq |= ((uint32_t)adc_channel << (ADC_INSERTED_CHANNEL_SHIFT_LENGTH-(inserted_length-rank)*ADC_INSERTED_CHANNEL_RANK_LENGTH)); + ADC_ISQ(adc_periph) = isq; + + /* ADC sampling time config */ + if(adc_channel < ADC_CHANNEL_SAMPLE_TEN){ + /* the inserted group sequence rank is smaller than ten */ + sampt = ADC_SAMPT1(adc_periph); + sampt &= ~((uint32_t)(ADC_SAMPTX_SPTN << (ADC_CHANNEL_SAMPLE_LENGTH*adc_channel))); + /* channel sample time set*/ + sampt |= (uint32_t) sample_time << (ADC_CHANNEL_SAMPLE_LENGTH*adc_channel); + ADC_SAMPT1(adc_periph) = sampt; + }else if(adc_channel < ADC_CHANNEL_SAMPLE_EIGHTEEN){ + /* the inserted group sequence rank is smaller than eighteen */ + sampt = ADC_SAMPT0(adc_periph); + sampt &= ~((uint32_t)(ADC_SAMPTX_SPTN << (ADC_CHANNEL_SAMPLE_LENGTH*(adc_channel-ADC_CHANNEL_SAMPLE_TEN)))); + /* channel sample time set*/ + sampt |= ((uint32_t)sample_time << (ADC_CHANNEL_SAMPLE_LENGTH*(adc_channel-ADC_CHANNEL_SAMPLE_TEN))); + ADC_SAMPT0(adc_periph) = sampt; + }else{ + } +} + +/*! + \brief configure ADC inserted channel offset + \param[in] adc_periph: ADCx, x=0,1 + \param[in] inserted_channel: insert channel select + only one parameter can be selected + \arg ADC_INSERTED_CHANNEL_0: inserted channel0 + \arg ADC_INSERTED_CHANNEL_1: inserted channel1 + \arg ADC_INSERTED_CHANNEL_2: inserted channel2 + \arg ADC_INSERTED_CHANNEL_3: inserted channel3 + \param[in] offset: the offset data + \param[out] none + \retval none +*/ +void adc_inserted_channel_offset_config(uint32_t adc_periph, uint8_t inserted_channel, uint16_t offset) +{ + uint8_t inserted_length; + uint32_t num = 0U; + + inserted_length = (uint8_t)GET_BITS(ADC_ISQ(adc_periph) , 20U , 21U); + num = ((uint32_t)ADC_OFFSET_LENGTH - ((uint32_t)inserted_length - (uint32_t)inserted_channel)); + + if(num <= ADC_OFFSET_LENGTH){ + /* calculate the offset of the register */ + num = num * ADC_OFFSET_SHIFT_LENGTH; + /* config the offset of the selected channels */ + REG32((adc_periph) + 0x14U + num) = IOFFX_IOFF((uint32_t)offset); + } +} + +/*! + \brief configure ADC external trigger source + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel_group: select the channel group + only one parameter can be selected which is shown as below: + \arg ADC_REGULAR_CHANNEL: regular channel group + \arg ADC_INSERTED_CHANNEL: inserted channel group + \param[in] external_trigger_source: regular or inserted group trigger source + only one parameter can be selected + for regular channel: + \arg ADC0_1_EXTTRIG_REGULAR_T0_CH0: TIMER0 CH0 event select + \arg ADC0_1_EXTTRIG_REGULAR_T0_CH1: TIMER0 CH1 event select + \arg ADC0_1_EXTTRIG_REGULAR_T0_CH2: TIMER0 CH2 event select + \arg ADC0_1_EXTTRIG_REGULAR_T1_CH1: TIMER1 CH1 event select + \arg ADC0_1_EXTTRIG_REGULAR_T2_TRGO: TIMER2 TRGO event select + \arg ADC0_1_EXTTRIG_REGULAR_T3_CH3: TIMER3 CH3 event select + \arg ADC0_1_EXTTRIG_REGULAR_EXTI_11: external interrupt line 11 + \arg ADC0_1_EXTTRIG_REGULAR_NONE: software trigger + for inserted channel: + \arg ADC0_1_EXTTRIG_INSERTED_T0_TRGO: TIMER0 TRGO event select + \arg ADC0_1_EXTTRIG_INSERTED_T0_CH3: TIMER0 CH3 event select + \arg ADC0_1_EXTTRIG_INSERTED_T1_TRGO: TIMER1 TRGO event select + \arg ADC0_1_EXTTRIG_INSERTED_T1_CH0: TIMER1 CH0 event select + \arg ADC0_1_EXTTRIG_INSERTED_T2_CH3: TIMER2 CH3 event select + \arg ADC0_1_EXTTRIG_INSERTED_T3_TRGO: TIMER3 TRGO event select + \arg ADC0_1_EXTTRIG_INSERTED_EXTI_15: external interrupt line 15 + \arg ADC0_1_EXTTRIG_INSERTED_NONE: software trigger + \param[out] none + \retval none +*/ +void adc_external_trigger_source_config(uint32_t adc_periph, uint8_t adc_channel_group, uint32_t external_trigger_source) +{ + switch(adc_channel_group){ + case ADC_REGULAR_CHANNEL: + /* configure ADC regular group external trigger source */ + ADC_CTL1(adc_periph) &= ~((uint32_t)ADC_CTL1_ETSRC); + ADC_CTL1(adc_periph) |= (uint32_t)external_trigger_source; + break; + case ADC_INSERTED_CHANNEL: + /* configure ADC inserted group external trigger source */ + ADC_CTL1(adc_periph) &= ~((uint32_t)ADC_CTL1_ETSIC); + ADC_CTL1(adc_periph) |= (uint32_t)external_trigger_source; + break; + default: + break; + } +} + +/*! + \brief configure ADC external trigger + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel_group: select the channel group + one or more parameters can be selected which are shown as below: + \arg ADC_REGULAR_CHANNEL: regular channel group + \arg ADC_INSERTED_CHANNEL: inserted channel group + \param[in] newvalue: ENABLE or DISABLE + \param[out] none + \retval none +*/ +void adc_external_trigger_config(uint32_t adc_periph, uint8_t adc_channel_group, ControlStatus newvalue) +{ + if(newvalue){ + if(0U != (adc_channel_group & ADC_REGULAR_CHANNEL)){ + /* enable ADC regular channel group external trigger */ + ADC_CTL1(adc_periph) |= ADC_CTL1_ETERC; + } + if(0U != (adc_channel_group & ADC_INSERTED_CHANNEL)){ + /* enable ADC inserted channel group external trigger */ + ADC_CTL1(adc_periph) |= ADC_CTL1_ETEIC; + } + }else{ + if(0U != (adc_channel_group & ADC_REGULAR_CHANNEL)){ + /* disable ADC regular channel group external trigger */ + ADC_CTL1(adc_periph) &= ~ADC_CTL1_ETERC; + } + if(0U != (adc_channel_group & ADC_INSERTED_CHANNEL)){ + /* disable ADC regular channel group external trigger */ + ADC_CTL1(adc_periph) &= ~ADC_CTL1_ETEIC; + } + } +} + +/*! + \brief enable ADC software trigger + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel_group: select the channel group + one or more parameters can be selected which are shown as below: + \arg ADC_REGULAR_CHANNEL: regular channel group + \arg ADC_INSERTED_CHANNEL: inserted channel group + \param[out] none + \retval none +*/ +void adc_software_trigger_enable(uint32_t adc_periph, uint8_t adc_channel_group) +{ + if(0U != (adc_channel_group & ADC_REGULAR_CHANNEL)){ + /* enable ADC regular channel group software trigger */ + ADC_CTL1(adc_periph) |= ADC_CTL1_SWRCST; + } + if(0U != (adc_channel_group & ADC_INSERTED_CHANNEL)){ + /* enable ADC inserted channel group software trigger */ + ADC_CTL1(adc_periph) |= ADC_CTL1_SWICST; + } +} + +/*! + \brief read ADC regular group data register + \param[in] adc_periph: ADCx, x=0,1 + \param[in] none + \param[out] none + \retval the conversion value +*/ +uint16_t adc_regular_data_read(uint32_t adc_periph) +{ + return (uint16_t)(ADC_RDATA(adc_periph)); +} + +/*! + \brief read ADC inserted group data register + \param[in] adc_periph: ADCx, x=0,1 + \param[in] inserted_channel: insert channel select + only one parameter can be selected + \arg ADC_INSERTED_CHANNEL_0: inserted Channel0 + \arg ADC_INSERTED_CHANNEL_1: inserted channel1 + \arg ADC_INSERTED_CHANNEL_2: inserted Channel2 + \arg ADC_INSERTED_CHANNEL_3: inserted Channel3 + \param[out] none + \retval the conversion value +*/ +uint16_t adc_inserted_data_read(uint32_t adc_periph, uint8_t inserted_channel) +{ + uint32_t idata; + /* read the data of the selected channel */ + switch(inserted_channel){ + case ADC_INSERTED_CHANNEL_0: + /* read the data of channel 0 */ + idata = ADC_IDATA0(adc_periph); + break; + case ADC_INSERTED_CHANNEL_1: + /* read the data of channel 1 */ + idata = ADC_IDATA1(adc_periph); + break; + case ADC_INSERTED_CHANNEL_2: + /* read the data of channel 2 */ + idata = ADC_IDATA2(adc_periph); + break; + case ADC_INSERTED_CHANNEL_3: + /* read the data of channel 3 */ + idata = ADC_IDATA3(adc_periph); + break; + default: + idata = 0U; + break; + } + return (uint16_t)idata; +} + +/*! + \brief read the last ADC0 and ADC1 conversion result data in sync mode + \param[in] none + \param[out] none + \retval the conversion value +*/ +uint32_t adc_sync_mode_convert_value_read(void) +{ + /* return conversion value */ + return ADC_RDATA(ADC0); +} + + +/*! + \brief configure ADC analog watchdog single channel + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel: the selected ADC channel + only one parameter can be selected which is shown as below: + \arg ADC_CHANNEL_x: ADC Channelx(x=0..17)(x=16 and x=17 are only for ADC0) + \param[out] none + \retval none +*/ +void adc_watchdog_single_channel_enable(uint32_t adc_periph, uint8_t adc_channel) +{ + ADC_CTL0(adc_periph) &= (uint32_t)~(ADC_CTL0_RWDEN | ADC_CTL0_IWDEN | ADC_CTL0_WDSC | ADC_CTL0_WDCHSEL); + /* analog watchdog channel select */ + ADC_CTL0(adc_periph) |= (uint32_t)adc_channel; + ADC_CTL0(adc_periph) |= (uint32_t)(ADC_CTL0_RWDEN | ADC_CTL0_IWDEN | ADC_CTL0_WDSC); +} + +/*! + \brief configure ADC analog watchdog group channel + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_channel_group: the channel group use analog watchdog + only one parameter can be selected which is shown as below: + \arg ADC_REGULAR_CHANNEL: regular channel group + \arg ADC_INSERTED_CHANNEL: inserted channel group + \arg ADC_REGULAR_INSERTED_CHANNEL: both regular and inserted group + \param[out] none + \retval none +*/ +void adc_watchdog_group_channel_enable(uint32_t adc_periph, uint8_t adc_channel_group) +{ + ADC_CTL0(adc_periph) &= (uint32_t)~(ADC_CTL0_RWDEN | ADC_CTL0_IWDEN | ADC_CTL0_WDSC); + /* select the group */ + switch(adc_channel_group){ + case ADC_REGULAR_CHANNEL: + /* regular channel analog watchdog enable */ + ADC_CTL0(adc_periph) |= (uint32_t) ADC_CTL0_RWDEN; + break; + case ADC_INSERTED_CHANNEL: + /* inserted channel analog watchdog enable */ + ADC_CTL0(adc_periph) |= (uint32_t) ADC_CTL0_IWDEN; + break; + case ADC_REGULAR_INSERTED_CHANNEL: + /* regular and inserted channel analog watchdog enable */ + ADC_CTL0(adc_periph) |= (uint32_t)(ADC_CTL0_RWDEN | ADC_CTL0_IWDEN); + break; + default: + break; + } +} + +/*! + \brief disable ADC analog watchdog + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_watchdog_disable(uint32_t adc_periph) +{ + ADC_CTL0(adc_periph) &= (uint32_t)~(ADC_CTL0_RWDEN | ADC_CTL0_IWDEN | ADC_CTL0_WDSC | ADC_CTL0_WDCHSEL); +} + +/*! + \brief configure ADC analog watchdog threshold + \param[in] adc_periph: ADCx, x=0,1 + \param[in] low_threshold: analog watchdog low threshold, 0..4095 + \param[in] high_threshold: analog watchdog high threshold, 0..4095 + \param[out] none + \retval none +*/ +void adc_watchdog_threshold_config(uint32_t adc_periph, uint16_t low_threshold, uint16_t high_threshold) +{ + ADC_WDLT(adc_periph) = (uint32_t)WDLT_WDLT(low_threshold); + ADC_WDHT(adc_periph) = (uint32_t)WDHT_WDHT(high_threshold); +} + +/*! + \brief get the ADC flag bits + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_flag: the adc flag bits + only one parameter can be selected which is shown as below: + \arg ADC_FLAG_WDE: analog watchdog event flag + \arg ADC_FLAG_EOC: end of group conversion flag + \arg ADC_FLAG_EOIC: end of inserted group conversion flag + \arg ADC_FLAG_STIC: start flag of inserted channel group + \arg ADC_FLAG_STRC: start flag of regular channel group + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus adc_flag_get(uint32_t adc_periph, uint32_t adc_flag) +{ + FlagStatus reval = RESET; + if(ADC_STAT(adc_periph) & adc_flag){ + reval = SET; + } + return reval; +} + +/*! + \brief clear the ADC flag bits + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_flag: the adc flag bits + one or more parameters can be selected which are shown as below: + \arg ADC_FLAG_WDE: analog watchdog event flag + \arg ADC_FLAG_EOC: end of group conversion flag + \arg ADC_FLAG_EOIC: end of inserted group conversion flag + \arg ADC_FLAG_STIC: start flag of inserted channel group + \arg ADC_FLAG_STRC: start flag of regular channel group + \param[out] none + \retval none +*/ +void adc_flag_clear(uint32_t adc_periph, uint32_t adc_flag) +{ + ADC_STAT(adc_periph) &= ~((uint32_t)adc_flag); +} + +/*! + \brief get the bit state of ADCx software start conversion + \param[in] adc_periph: ADCx, x=0,1 + \param[in] none + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus adc_regular_software_startconv_flag_get(uint32_t adc_periph) +{ + FlagStatus reval = RESET; + if((uint32_t)RESET != (ADC_CTL1(adc_periph) & ADC_CTL1_SWRCST)){ + reval = SET; + } + return reval; +} + +/*! + \brief get the bit state of ADCx software inserted channel start conversion + \param[in] adc_periph: ADCx, x=0,1 + \param[in] none + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus adc_inserted_software_startconv_flag_get(uint32_t adc_periph) +{ + FlagStatus reval = RESET; + if((uint32_t)RESET != (ADC_CTL1(adc_periph) & ADC_CTL1_SWICST)){ + reval = SET; + } + return reval; +} + +/*! + \brief get the ADC interrupt bits + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_interrupt: the adc interrupt bits + only one parameter can be selected which is shown as below: + \arg ADC_INT_FLAG_WDE: analog watchdog interrupt + \arg ADC_INT_FLAG_EOC: end of group conversion interrupt + \arg ADC_INT_FLAG_EOIC: end of inserted group conversion interrupt + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus adc_interrupt_flag_get(uint32_t adc_periph, uint32_t adc_interrupt) +{ + FlagStatus interrupt_flag = RESET; + uint32_t state; + /* check the interrupt bits */ + switch(adc_interrupt){ + case ADC_INT_FLAG_WDE: + /* get the ADC analog watchdog interrupt bits */ + state = ADC_STAT(adc_periph) & ADC_STAT_WDE; + if((ADC_CTL0(adc_periph) & ADC_CTL0_WDEIE) && state){ + interrupt_flag = SET; + } + break; + case ADC_INT_FLAG_EOC: + /* get the ADC end of group conversion interrupt bits */ + state = ADC_STAT(adc_periph) & ADC_STAT_EOC; + if((ADC_CTL0(adc_periph) & ADC_CTL0_EOCIE) && state){ + interrupt_flag = SET; + } + break; + case ADC_INT_FLAG_EOIC: + /* get the ADC end of inserted group conversion interrupt bits */ + state = ADC_STAT(adc_periph) & ADC_STAT_EOIC; + if((ADC_CTL0(adc_periph) & ADC_CTL0_EOICIE) && state){ + interrupt_flag = SET; + } + break; + default: + break; + } + return interrupt_flag; +} + +/*! + \brief clear the ADC flag + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_interrupt: the adc status flag + one or more parameters can be selected which are shown as below: + \arg ADC_INT_FLAG_WDE: analog watchdog interrupt + \arg ADC_INT_FLAG_EOC: end of group conversion interrupt + \arg ADC_INT_FLAG_EOIC: end of inserted group conversion interrupt + \param[out] none + \retval none +*/ +void adc_interrupt_flag_clear(uint32_t adc_periph, uint32_t adc_interrupt) +{ + ADC_STAT(adc_periph) &= ~((uint32_t)adc_interrupt); +} + +/*! + \brief enable ADC interrupt + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_interrupt: the adc interrupt + one or more parameters can be selected which are shown as below: + \arg ADC_INT_WDE: analog watchdog interrupt flag + \arg ADC_INT_EOC: end of group conversion interrupt flag + \arg ADC_INT_EOIC: end of inserted group conversion interrupt flag + \param[out] none + \retval none +*/ +void adc_interrupt_enable(uint32_t adc_periph, uint32_t adc_interrupt) +{ + /* enable ADC analog watchdog interrupt */ + if(0U != (adc_interrupt & ADC_INT_WDE)){ + ADC_CTL0(adc_periph) |= (uint32_t) ADC_CTL0_WDEIE; + } + /* enable ADC end of group conversion interrupt */ + if(0U != (adc_interrupt & ADC_INT_EOC)){ + ADC_CTL0(adc_periph) |= (uint32_t) ADC_CTL0_EOCIE; + } + /* enable ADC end of inserted group conversion interrupt */ + if(0U != (adc_interrupt & ADC_INT_EOIC)){ + ADC_CTL0(adc_periph) |= (uint32_t) ADC_CTL0_EOICIE; + } +} + +/*! + \brief disable ADC interrupt + \param[in] adc_periph: ADCx, x=0,1 + \param[in] adc_interrupt: the adc interrupt flag + one or more parameters can be selected which are shown as below: + \arg ADC_INT_WDE: analog watchdog interrupt flag + \arg ADC_INT_EOC: end of group conversion interrupt flag + \arg ADC_INT_EOIC: end of inserted group conversion interrupt flag + \param[out] none + \retval none +*/ +void adc_interrupt_disable(uint32_t adc_periph, uint32_t adc_interrupt) +{ + /* disable ADC analog watchdog interrupt */ + if(0U != (adc_interrupt & ADC_INT_WDE)){ + ADC_CTL0(adc_periph) &= ~(uint32_t) ADC_CTL0_WDEIE; + } + /* disable ADC end of group conversion interrupt */ + if(0U != (adc_interrupt & ADC_INT_EOC)){ + ADC_CTL0(adc_periph) &= ~(uint32_t) ADC_CTL0_EOCIE; + } + /* disable ADC end of inserted group conversion interrupt */ + if(0U != (adc_interrupt & ADC_INT_EOIC)){ + ADC_CTL0(adc_periph) &= ~(uint32_t) ADC_CTL0_EOICIE; + } +} + +/*! + \brief adc resolution config + \param[in] adc_periph: ADCx, x=0,1 + \param[in] resolution: ADC resolution + only one parameter can be selected which is shown as below: + \arg ADC_RESOLUTION_12B: 12-bit ADC resolution + \arg ADC_RESOLUTION_10B: 10-bit ADC resolution + \arg ADC_RESOLUTION_8B: 8-bit ADC resolution + \arg ADC_RESOLUTION_6B: 6-bit ADC resolution + \param[out] none + \retval none +*/ +void adc_resolution_config(uint32_t adc_periph, uint32_t resolution) +{ + ADC_OVSCR(adc_periph) &= ~((uint32_t)ADC_OVSCR_DRES); + ADC_OVSCR(adc_periph) |= (uint32_t)resolution; +} + +/*! + \brief adc oversample mode config + \param[in] adc_periph: ADCx, x=0,1 + \param[in] mode: ADC oversampling mode + only one parameter can be selected which is shown as below: + \arg ADC_OVERSAMPLING_ALL_CONVERT: all oversampled conversions for a channel + are done consecutively after a trigger + \arg ADC_OVERSAMPLING_ONE_CONVERT: each oversampled conversion for a channel + needs a trigger + \param[in] shift: ADC oversampling shift + only one parameter can be selected which is shown as below: + \arg ADC_OVERSAMPLING_SHIFT_NONE: no oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_1B: 1-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_2B: 2-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_3B: 3-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_4B: 3-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_5B: 5-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_6B: 6-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_7B: 7-bit oversampling shift + \arg ADC_OVERSAMPLING_SHIFT_8B: 8-bit oversampling shift + \param[in] ratio: ADC oversampling ratio + only one parameter can be selected which is shown as below: + \arg ADC_OVERSAMPLING_RATIO_MUL2: oversampling ratio X2 + \arg ADC_OVERSAMPLING_RATIO_MUL4: oversampling ratio X4 + \arg ADC_OVERSAMPLING_RATIO_MUL8: oversampling ratio X8 + \arg ADC_OVERSAMPLING_RATIO_MUL16: oversampling ratio X16 + \arg ADC_OVERSAMPLING_RATIO_MUL32: oversampling ratio X32 + \arg ADC_OVERSAMPLING_RATIO_MUL64: oversampling ratio X64 + \arg ADC_OVERSAMPLING_RATIO_MUL128: oversampling ratio X128 + \arg ADC_OVERSAMPLING_RATIO_MUL256: oversampling ratio X256 + \param[out] none + \retval none +*/ +void adc_oversample_mode_config(uint32_t adc_periph, uint8_t mode, uint16_t shift,uint8_t ratio) +{ + if(mode){ + ADC_OVSCR(adc_periph) |= (uint32_t)ADC_OVSCR_TOVS; + }else{ + ADC_OVSCR(adc_periph) &= ~((uint32_t)ADC_OVSCR_TOVS); + } + /* config the shift and ratio */ + ADC_OVSCR(adc_periph) &= ~((uint32_t)(ADC_OVSCR_OVSR | ADC_OVSCR_OVSS)); + ADC_OVSCR(adc_periph) |= ((uint32_t)shift | (uint32_t)ratio); +} + +/*! + \brief enable ADC oversample mode + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_oversample_mode_enable(uint32_t adc_periph) +{ + ADC_OVSCR(adc_periph) |= ADC_OVSCR_OVSEN; +} + +/*! + \brief disable ADC oversample mode + \param[in] adc_periph: ADCx, x=0,1 + \param[out] none + \retval none +*/ +void adc_oversample_mode_disable(uint32_t adc_periph) +{ + ADC_OVSCR(adc_periph) &= ~((uint32_t)ADC_OVSCR_OVSEN); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_bkp.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_bkp.c new file mode 100644 index 00000000..e3b01e4c --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_bkp.c @@ -0,0 +1,292 @@ +/*! + \file gd32vf103_bkp.c + \brief BKP driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_bkp.h" + +/* BKP register bits offset */ +#define BKP_TAMPER_BITS_OFFSET ((uint32_t)8U) + +/*! + \brief reset BKP registers + \param[in] none + \param[out] none + \retval none +*/ +void bkp_deinit(void) +{ + /* reset BKP domain register*/ + rcu_bkp_reset_enable(); + rcu_bkp_reset_disable(); +} + +/*! + \brief write BKP data register + \param[in] register_number: refer to bkp_data_register_enum + only one parameter can be selected which is shown as below: + \arg BKP_DATA_x(x = 0..41): bkp data register number x + \param[in] data: the data to be write in BKP data register + \param[out] none + \retval none +*/ +void bkp_data_write(bkp_data_register_enum register_number, uint16_t data) +{ + if((register_number >= BKP_DATA_10) && (register_number <= BKP_DATA_41)){ + BKP_DATA10_41(register_number - 1U) = data; + }else if((register_number >= BKP_DATA_0) && (register_number <= BKP_DATA_9)){ + BKP_DATA0_9(register_number - 1U) = data; + }else{ + /* illegal parameters */ + } +} + +/*! + \brief read BKP data register + \param[in] register_number: refer to bkp_data_register_enum + only one parameter can be selected which is shown as below: + \arg BKP_DATA_x(x = 0..41): bkp data register number x + \param[out] none + \retval data of BKP data register +*/ +uint16_t bkp_data_read(bkp_data_register_enum register_number) +{ + uint16_t data = 0U; + + /* get the data from the BKP data register */ + if((register_number >= BKP_DATA_10) && (register_number <= BKP_DATA_41)){ + data = BKP_DATA10_41(register_number - 1U); + }else if((register_number >= BKP_DATA_0) && (register_number <= BKP_DATA_9)){ + data = BKP_DATA0_9(register_number - 1U); + }else{ + /* illegal parameters */ + } + return data; +} + +/*! + \brief enable RTC clock calibration output + \param[in] none + \param[out] none + \retval none +*/ +void bkp_rtc_calibration_output_enable(void) +{ + BKP_OCTL |= (uint16_t)BKP_OCTL_COEN; +} + +/*! + \brief disable RTC clock calibration output + \param[in] none + \param[out] none + \retval none +*/ +void bkp_rtc_calibration_output_disable(void) +{ + BKP_OCTL &= (uint16_t)~BKP_OCTL_COEN; +} + +/*! + \brief enable RTC alarm or second signal output + \param[in] none + \param[out] none + \retval none +*/ +void bkp_rtc_signal_output_enable(void) +{ + BKP_OCTL |= (uint16_t)BKP_OCTL_ASOEN; +} + +/*! + \brief disable RTC alarm or second signal output + \param[in] none + \param[out] none + \retval none +*/ +void bkp_rtc_signal_output_disable(void) +{ + BKP_OCTL &= (uint16_t)~BKP_OCTL_ASOEN; +} + +/*! + \brief select RTC output + \param[in] outputsel: RTC output selection + only one parameter can be selected which is shown as below: + \arg RTC_OUTPUT_ALARM_PULSE: RTC alarm pulse is selected as the RTC output + \arg RTC_OUTPUT_SECOND_PULSE: RTC second pulse is selected as the RTC output + \param[out] none + \retval none +*/ +void bkp_rtc_output_select(uint16_t outputsel) +{ + uint16_t ctl = 0U; + + /* configure BKP_OCTL_ROSEL with outputsel */ + ctl = BKP_OCTL; + ctl &= (uint16_t)~BKP_OCTL_ROSEL; + ctl |= outputsel; + BKP_OCTL = ctl; +} + +/*! + \brief set RTC clock calibration value + \param[in] value: RTC clock calibration value + \arg 0x00 - 0x7F + \param[out] none + \retval none +*/ +void bkp_rtc_calibration_value_set(uint8_t value) +{ + uint16_t ctl; + + /* configure BKP_OCTL_RCCV with value */ + ctl = BKP_OCTL; + ctl &= (uint16_t)~BKP_OCTL_RCCV; + ctl |= (uint16_t)OCTL_RCCV(value); + BKP_OCTL = ctl; +} + +/*! + \brief enable tamper detection + \param[in] none + \param[out] none + \retval none +*/ +void bkp_tamper_detection_enable(void) +{ + BKP_TPCTL |= (uint16_t)BKP_TPCTL_TPEN; +} + +/*! + \brief disable tamper detection + \param[in] none + \param[out] none + \retval none +*/ +void bkp_tamper_detection_disable(void) +{ + BKP_TPCTL &= (uint16_t)~BKP_TPCTL_TPEN; +} + +/*! + \brief set tamper pin active level + \param[in] level: tamper active level + only one parameter can be selected which is shown as below: + \arg TAMPER_PIN_ACTIVE_HIGH: the tamper pin is active high + \arg TAMPER_PIN_ACTIVE_LOW: the tamper pin is active low + \param[out] none + \retval none +*/ +void bkp_tamper_active_level_set(uint16_t level) +{ + uint16_t ctl = 0U; + + /* configure BKP_TPCTL_TPAL with level */ + ctl = BKP_TPCTL; + ctl &= (uint16_t)~BKP_TPCTL_TPAL; + ctl |= level; + BKP_TPCTL = ctl; +} + +/*! + \brief enable tamper interrupt + \param[in] none + \param[out] none + \retval none +*/ +void bkp_interrupt_enable(void) +{ + BKP_TPCS |= (uint16_t)BKP_TPCS_TPIE; +} + +/*! + \brief disable tamper interrupt + \param[in] none + \param[out] none + \retval none +*/ +void bkp_interrupt_disable(void) +{ + BKP_TPCS &= (uint16_t)~BKP_TPCS_TPIE; +} + +/*! + \brief get tamper flag state + \param[in] none + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus bkp_flag_get(void) +{ + if(RESET != (BKP_TPCS & BKP_FLAG_TAMPER)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear tamper flag state + \param[in] none + \param[out] none + \retval none +*/ +void bkp_flag_clear(void) +{ + BKP_TPCS |= (uint16_t)(BKP_FLAG_TAMPER >> BKP_TAMPER_BITS_OFFSET); +} + +/*! + \brief get tamper interrupt flag state + \param[in] none + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus bkp_interrupt_flag_get(void) +{ + if(RESET != (BKP_TPCS & BKP_INT_FLAG_TAMPER)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear tamper interrupt flag state + \param[in] none + \param[out] none + \retval none +*/ +void bkp_interrupt_flag_clear(void) +{ + BKP_TPCS |= (uint16_t)(BKP_INT_FLAG_TAMPER >> BKP_TAMPER_BITS_OFFSET); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_can.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_can.c new file mode 100644 index 00000000..ef8bd8eb --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_can.c @@ -0,0 +1,989 @@ +/*! + \file gd32vf103_can.c + \brief CAN driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_can.h" + +#define CAN_ERROR_HANDLE(s) do{}while(1) + +/*! + \brief deinitialize CAN + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval none +*/ +void can_deinit(uint32_t can_periph) +{ + if(CAN0 == can_periph){ + rcu_periph_reset_enable(RCU_CAN0RST); + rcu_periph_reset_disable(RCU_CAN0RST); + }else{ + rcu_periph_reset_enable(RCU_CAN1RST); + rcu_periph_reset_disable(RCU_CAN1RST); + } +} + +/*! + \brief initialize CAN parameter struct with a default value + \param[in] type: the type of CAN parameter struct + only one parameter can be selected which is shown as below: + \arg CAN_INIT_STRUCT: the CAN initial struct + \arg CAN_FILTER_STRUCT: the CAN filter struct + \arg CAN_TX_MESSAGE_STRUCT: the CAN TX message struct + \arg CAN_RX_MESSAGE_STRUCT: the CAN RX message struct + \param[in] p_struct: the pointer of the specific struct + \param[out] none + \retval none +*/ +void can_struct_para_init(can_struct_type_enum type, void* p_struct) +{ + uint8_t i; + + /* get type of the struct */ + switch(type){ + /* used for can_init() */ + case CAN_INIT_STRUCT: + ((can_parameter_struct*)p_struct)->auto_bus_off_recovery = DISABLE; + ((can_parameter_struct*)p_struct)->no_auto_retrans = DISABLE; + ((can_parameter_struct*)p_struct)->auto_wake_up = DISABLE; + ((can_parameter_struct*)p_struct)->prescaler = 0x03FFU; + ((can_parameter_struct*)p_struct)->rec_fifo_overwrite = DISABLE; + ((can_parameter_struct*)p_struct)->resync_jump_width = CAN_BT_SJW_1TQ; + ((can_parameter_struct*)p_struct)->time_segment_1 = CAN_BT_BS1_3TQ; + ((can_parameter_struct*)p_struct)->time_segment_2 = CAN_BT_BS2_1TQ; + ((can_parameter_struct*)p_struct)->time_triggered = DISABLE; + ((can_parameter_struct*)p_struct)->trans_fifo_order = DISABLE; + ((can_parameter_struct*)p_struct)->working_mode = CAN_NORMAL_MODE; + + break; + /* used for can_filter_init() */ + case CAN_FILTER_STRUCT: + ((can_filter_parameter_struct*)p_struct)->filter_bits = CAN_FILTERBITS_32BIT; + ((can_filter_parameter_struct*)p_struct)->filter_enable = DISABLE; + ((can_filter_parameter_struct*)p_struct)->filter_fifo_number = CAN_FIFO0; + ((can_filter_parameter_struct*)p_struct)->filter_list_high = 0x0000U; + ((can_filter_parameter_struct*)p_struct)->filter_list_low = 0x0000U; + ((can_filter_parameter_struct*)p_struct)->filter_mask_high = 0x0000U; + ((can_filter_parameter_struct*)p_struct)->filter_mask_low = 0x0000U; + ((can_filter_parameter_struct*)p_struct)->filter_mode = CAN_FILTERMODE_MASK; + ((can_filter_parameter_struct*)p_struct)->filter_number = 0U; + + break; + /* used for can_message_transmit() */ + case CAN_TX_MESSAGE_STRUCT: + for(i = 0U; i < 8U; i++){ + ((can_trasnmit_message_struct*)p_struct)->tx_data[i] = 0U; + } + + ((can_trasnmit_message_struct*)p_struct)->tx_dlen = 0u; + ((can_trasnmit_message_struct*)p_struct)->tx_efid = 0U; + ((can_trasnmit_message_struct*)p_struct)->tx_ff = (uint8_t)CAN_FF_STANDARD; + ((can_trasnmit_message_struct*)p_struct)->tx_ft = (uint8_t)CAN_FT_DATA; + ((can_trasnmit_message_struct*)p_struct)->tx_sfid = 0U; + + break; + /* used for can_message_receive() */ + case CAN_RX_MESSAGE_STRUCT: + for(i = 0U; i < 8U; i++){ + ((can_receive_message_struct*)p_struct)->rx_data[i] = 0U; + } + + ((can_receive_message_struct*)p_struct)->rx_dlen = 0U; + ((can_receive_message_struct*)p_struct)->rx_efid = 0U; + ((can_receive_message_struct*)p_struct)->rx_ff = (uint8_t)CAN_FF_STANDARD; + ((can_receive_message_struct*)p_struct)->rx_fi = 0U; + ((can_receive_message_struct*)p_struct)->rx_ft = (uint8_t)CAN_FT_DATA; + ((can_receive_message_struct*)p_struct)->rx_sfid = 0U; + + break; + + default: + CAN_ERROR_HANDLE("parameter is invalid \r\n"); + } +} + +/*! + \brief initialize CAN + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] can_parameter_init: parameters for CAN initializtion + \arg working_mode: CAN_NORMAL_MODE, CAN_LOOPBACK_MODE, CAN_SILENT_MODE, CAN_SILENT_LOOPBACK_MODE + \arg resync_jump_width: CAN_BT_SJW_xTQ(x=1, 2, 3, 4) + \arg time_segment_1: CAN_BT_BS1_xTQ(1..16) + \arg time_segment_2: CAN_BT_BS2_xTQ(1..8) + \arg time_triggered: ENABLE or DISABLE + \arg auto_bus_off_recovery: ENABLE or DISABLE + \arg auto_wake_up: ENABLE or DISABLE + \arg no_auto_retrans: ENABLE or DISABLE + \arg rec_fifo_overwrite: ENABLE or DISABLE + \arg trans_fifo_order: ENABLE or DISABLE + \arg prescaler: 0x0000 - 0x03FF + \param[out] none + \retval ErrStatus: SUCCESS or ERROR +*/ +ErrStatus can_init(uint32_t can_periph, can_parameter_struct* can_parameter_init) +{ + uint32_t timeout = CAN_TIMEOUT; + ErrStatus flag = ERROR; + + /* disable sleep mode */ + CAN_CTL(can_periph) &= ~CAN_CTL_SLPWMOD; + /* enable initialize mode */ + CAN_CTL(can_periph) |= CAN_CTL_IWMOD; + /* wait ACK */ + while((CAN_STAT_IWS != (CAN_STAT(can_periph) & CAN_STAT_IWS)) && (0U != timeout)){ + timeout--; + } + /* check initialize working success */ + if(CAN_STAT_IWS != (CAN_STAT(can_periph) & CAN_STAT_IWS)){ + flag = ERROR; + }else{ + /* set the bit timing register */ + CAN_BT(can_periph) = (BT_MODE((uint32_t)can_parameter_init->working_mode) | \ + BT_SJW((uint32_t)can_parameter_init->resync_jump_width) | \ + BT_BS1((uint32_t)can_parameter_init->time_segment_1) | \ + BT_BS2((uint32_t)can_parameter_init->time_segment_2) | \ + BT_BAUDPSC(((uint32_t)(can_parameter_init->prescaler) - 1U))); + + /* time trigger communication mode */ + if(ENABLE == can_parameter_init->time_triggered){ + CAN_CTL(can_periph) |= CAN_CTL_TTC; + }else{ + CAN_CTL(can_periph) &= ~CAN_CTL_TTC; + } + /* automatic bus-off managment */ + if(ENABLE == can_parameter_init->auto_bus_off_recovery){ + CAN_CTL(can_periph) |= CAN_CTL_ABOR; + }else{ + CAN_CTL(can_periph) &= ~CAN_CTL_ABOR; + } + /* automatic wakeup mode */ + if(ENABLE == can_parameter_init->auto_wake_up){ + CAN_CTL(can_periph) |= CAN_CTL_AWU; + }else{ + CAN_CTL(can_periph) &= ~CAN_CTL_AWU; + } + /* automatic retransmission mode disable*/ + if(ENABLE == can_parameter_init->no_auto_retrans){ + CAN_CTL(can_periph) |= CAN_CTL_ARD; + }else{ + CAN_CTL(can_periph) &= ~CAN_CTL_ARD; + } + /* receive fifo overwrite mode */ + if(ENABLE == can_parameter_init->rec_fifo_overwrite){ + CAN_CTL(can_periph) |= CAN_CTL_RFOD; + }else{ + CAN_CTL(can_periph) &= ~CAN_CTL_RFOD; + } + /* transmit fifo order */ + if(ENABLE == can_parameter_init->trans_fifo_order){ + CAN_CTL(can_periph) |= CAN_CTL_TFO; + }else{ + CAN_CTL(can_periph) &= ~CAN_CTL_TFO; + } + /* disable initialize mode */ + CAN_CTL(can_periph) &= ~CAN_CTL_IWMOD; + timeout = CAN_TIMEOUT; + /* wait the ACK */ + while((CAN_STAT_IWS == (CAN_STAT(can_periph) & CAN_STAT_IWS)) && (0U != timeout)){ + timeout--; + } + /* check exit initialize mode */ + if(0U != timeout){ + flag = SUCCESS; + } + } + CAN_TMI0(can_periph) = 0x0; + CAN_TMI1(can_periph) = 0x0; + CAN_TMI2(can_periph) = 0x0; + CAN_TMP0(can_periph) = 0x0; + CAN_TMP1(can_periph) = 0x0; + CAN_TMP2(can_periph) = 0x0; + CAN_TMDATA00(can_periph) = 0x0; + CAN_TMDATA01(can_periph) = 0x0; + CAN_TMDATA02(can_periph) = 0x0; + CAN_TMDATA10(can_periph) = 0x0; + CAN_TMDATA11(can_periph) = 0x0; + CAN_TMDATA12(can_periph) = 0x0; + + return flag; +} + +/*! + \brief initialize CAN filter + \param[in] can_filter_parameter_init: struct for CAN filter initialization + \arg filter_list_high: 0x0000 - 0xFFFF + \arg filter_list_low: 0x0000 - 0xFFFF + \arg filter_mask_high: 0x0000 - 0xFFFF + \arg filter_mask_low: 0x0000 - 0xFFFF + \arg filter_fifo_number: CAN_FIFO0, CAN_FIFO1 + \arg filter_number: 0 - 27 + \arg filter_mode: CAN_FILTERMODE_MASK, CAN_FILTERMODE_LIST + \arg filter_bits: CAN_FILTERBITS_32BIT, CAN_FILTERBITS_16BIT + \arg filter_enable: ENABLE or DISABLE + \param[out] none + \retval none +*/ +void can_filter_init(can_filter_parameter_struct* can_filter_parameter_init) +{ + uint32_t val = 0U; + + val = ((uint32_t)1) << (can_filter_parameter_init->filter_number); + /* filter lock disable */ + CAN_FCTL(CAN0) |= CAN_FCTL_FLD; + /* disable filter */ + CAN_FW(CAN0) &= ~(uint32_t)val; + + /* filter 16 bits */ + if(CAN_FILTERBITS_16BIT == can_filter_parameter_init->filter_bits){ + /* set filter 16 bits */ + CAN_FSCFG(CAN0) &= ~(uint32_t)val; + /* first 16 bits list and first 16 bits mask or first 16 bits list and second 16 bits list */ + CAN_FDATA0(CAN0, can_filter_parameter_init->filter_number) = \ + FDATA_MASK_HIGH((can_filter_parameter_init->filter_mask_low) & CAN_FILTER_MASK_16BITS) | \ + FDATA_MASK_LOW((can_filter_parameter_init->filter_list_low) & CAN_FILTER_MASK_16BITS); + /* second 16 bits list and second 16 bits mask or third 16 bits list and fourth 16 bits list */ + CAN_FDATA1(CAN0, can_filter_parameter_init->filter_number) = \ + FDATA_MASK_HIGH((can_filter_parameter_init->filter_mask_high) & CAN_FILTER_MASK_16BITS) | \ + FDATA_MASK_LOW((can_filter_parameter_init->filter_list_high) & CAN_FILTER_MASK_16BITS); + } + /* filter 32 bits */ + if(CAN_FILTERBITS_32BIT == can_filter_parameter_init->filter_bits){ + /* set filter 32 bits */ + CAN_FSCFG(CAN0) |= (uint32_t)val; + /* 32 bits list or first 32 bits list */ + CAN_FDATA0(CAN0, can_filter_parameter_init->filter_number) = \ + FDATA_MASK_HIGH((can_filter_parameter_init->filter_list_high) & CAN_FILTER_MASK_16BITS) | + FDATA_MASK_LOW((can_filter_parameter_init->filter_list_low) & CAN_FILTER_MASK_16BITS); + /* 32 bits mask or second 32 bits list */ + CAN_FDATA1(CAN0, can_filter_parameter_init->filter_number) = \ + FDATA_MASK_HIGH((can_filter_parameter_init->filter_mask_high) & CAN_FILTER_MASK_16BITS) | + FDATA_MASK_LOW((can_filter_parameter_init->filter_mask_low) & CAN_FILTER_MASK_16BITS); + } + + /* filter mode */ + if(CAN_FILTERMODE_MASK == can_filter_parameter_init->filter_mode){ + /* mask mode */ + CAN_FMCFG(CAN0) &= ~(uint32_t)val; + }else{ + /* list mode */ + CAN_FMCFG(CAN0) |= (uint32_t)val; + } + + /* filter FIFO */ + if(CAN_FIFO0 == (can_filter_parameter_init->filter_fifo_number)){ + /* FIFO0 */ + CAN_FAFIFO(CAN0) &= ~(uint32_t)val; + }else{ + /* FIFO1 */ + CAN_FAFIFO(CAN0) |= (uint32_t)val; + } + + /* filter working */ + if(ENABLE == can_filter_parameter_init->filter_enable){ + + CAN_FW(CAN0) |= (uint32_t)val; + } + + /* filter lock enable */ + CAN_FCTL(CAN0) &= ~CAN_FCTL_FLD; +} + +/*! + \brief set CAN1 fliter start bank number + \param[in] start_bank: CAN1 start bank number + only one parameter can be selected which is shown as below: + \arg (1..27) + \param[out] none + \retval none +*/ +void can1_filter_start_bank(uint8_t start_bank) +{ + /* filter lock disable */ + CAN_FCTL(CAN0) |= CAN_FCTL_FLD; + /* set CAN1 filter start number */ + CAN_FCTL(CAN0) &= ~(uint32_t)CAN_FCTL_HBC1F; + CAN_FCTL(CAN0) |= FCTL_HBC1F(start_bank); + /* filter lock enaable */ + CAN_FCTL(CAN0) &= ~CAN_FCTL_FLD; +} + +/*! + \brief enable CAN debug freeze + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval none +*/ +void can_debug_freeze_enable(uint32_t can_periph) +{ + /* set DFZ bit */ + CAN_CTL(can_periph) |= CAN_CTL_DFZ; + if(CAN0 == can_periph){ + dbg_periph_enable(DBG_CAN0_HOLD); + }else{ + dbg_periph_enable(DBG_CAN1_HOLD); + } +} + +/*! + \brief disable CAN debug freeze + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval none +*/ +void can_debug_freeze_disable(uint32_t can_periph) +{ + /* set DFZ bit */ + CAN_CTL(can_periph) &= ~CAN_CTL_DFZ; + if(CAN0 == can_periph){ + dbg_periph_disable(DBG_CAN0_HOLD); + }else{ + dbg_periph_disable(DBG_CAN1_HOLD); + } +} + +/*! + \brief enable CAN time trigger mode + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval none +*/ +void can_time_trigger_mode_enable(uint32_t can_periph) +{ + uint8_t mailbox_number; + + /* enable the tcc mode */ + CAN_CTL(can_periph) |= CAN_CTL_TTC; + /* enable time stamp */ + for(mailbox_number = 0U; mailbox_number < 3U; mailbox_number++){ + CAN_TMP(can_periph, mailbox_number) |= CAN_TMP_TSEN; + } +} + +/*! + \brief disable CAN time trigger mode + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval none +*/ +void can_time_trigger_mode_disable(uint32_t can_periph) +{ + uint8_t mailbox_number; + + /* disable the TCC mode */ + CAN_CTL(can_periph) &= ~CAN_CTL_TTC; + /* reset TSEN bits */ + for(mailbox_number = 0U; mailbox_number < 3U; mailbox_number++){ + CAN_TMP(can_periph, mailbox_number) &= ~CAN_TMP_TSEN; + } +} + +/*! + \brief transmit CAN message + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] transmit_message: struct for CAN transmit message + \arg tx_sfid: 0x00000000 - 0x000007FF + \arg tx_efid: 0x00000000 - 0x1FFFFFFF + \arg tx_ff: CAN_FF_STANDARD, CAN_FF_EXTENDED + \arg tx_ft: CAN_FT_DATA, CAN_FT_REMOTE + \arg tx_dlenc: 1 - 7 + \arg tx_data[]: 0x00 - 0xFF + \param[out] none + \retval mailbox_number +*/ +uint8_t can_message_transmit(uint32_t can_periph, can_trasnmit_message_struct* transmit_message) +{ + uint8_t mailbox_number = CAN_MAILBOX0; + + /* select one empty mailbox */ + if(CAN_TSTAT_TME0 == (CAN_TSTAT(can_periph)&CAN_TSTAT_TME0)){ + mailbox_number = CAN_MAILBOX0; + }else if(CAN_TSTAT_TME1 == (CAN_TSTAT(can_periph)&CAN_TSTAT_TME1)){ + mailbox_number = CAN_MAILBOX1; + }else if(CAN_TSTAT_TME2 == (CAN_TSTAT(can_periph)&CAN_TSTAT_TME2)){ + mailbox_number = CAN_MAILBOX2; + }else{ + mailbox_number = CAN_NOMAILBOX; + } + /* return no mailbox empty */ + if(CAN_NOMAILBOX == mailbox_number){ + return CAN_NOMAILBOX; + } + + CAN_TMI(can_periph, mailbox_number) &= CAN_TMI_TEN; + if(CAN_FF_STANDARD == transmit_message->tx_ff){ + /* set transmit mailbox standard identifier */ + CAN_TMI(can_periph, mailbox_number) |= (uint32_t)(TMI_SFID(transmit_message->tx_sfid) | \ + transmit_message->tx_ft); + }else{ + /* set transmit mailbox extended identifier */ + CAN_TMI(can_periph, mailbox_number) |= (uint32_t)(TMI_EFID(transmit_message->tx_efid) | \ + transmit_message->tx_ff | \ + transmit_message->tx_ft); + } + /* set the data length */ + CAN_TMP(can_periph, mailbox_number) &= ~CAN_TMP_DLENC; + CAN_TMP(can_periph, mailbox_number) |= transmit_message->tx_dlen; + /* set the data */ + CAN_TMDATA0(can_periph, mailbox_number) = TMDATA0_DB3(transmit_message->tx_data[3]) | \ + TMDATA0_DB2(transmit_message->tx_data[2]) | \ + TMDATA0_DB1(transmit_message->tx_data[1]) | \ + TMDATA0_DB0(transmit_message->tx_data[0]); + CAN_TMDATA1(can_periph, mailbox_number) = TMDATA1_DB7(transmit_message->tx_data[7]) | \ + TMDATA1_DB6(transmit_message->tx_data[6]) | \ + TMDATA1_DB5(transmit_message->tx_data[5]) | \ + TMDATA1_DB4(transmit_message->tx_data[4]); + /* enable transmission */ + CAN_TMI(can_periph, mailbox_number) |= CAN_TMI_TEN; + + return mailbox_number; +} + +/*! + \brief get CAN transmit state + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] mailbox_number + only one parameter can be selected which is shown as below: + \arg CAN_MAILBOX(x=0,1,2) + \param[out] none + \retval can_transmit_state_enum +*/ +can_transmit_state_enum can_transmit_states(uint32_t can_periph, uint8_t mailbox_number) +{ + can_transmit_state_enum state = CAN_TRANSMIT_FAILED; + uint32_t val = 0U; + + /* check selected mailbox state */ + switch(mailbox_number){ + /* mailbox0 */ + case CAN_MAILBOX0: + val = CAN_TSTAT(can_periph) & (CAN_TSTAT_MTF0 | CAN_TSTAT_MTFNERR0 | CAN_TSTAT_TME0); + break; + /* mailbox1 */ + case CAN_MAILBOX1: + val = CAN_TSTAT(can_periph) & (CAN_TSTAT_MTF1 | CAN_TSTAT_MTFNERR1 | CAN_TSTAT_TME1); + break; + /* mailbox2 */ + case CAN_MAILBOX2: + val = CAN_TSTAT(can_periph) & (CAN_TSTAT_MTF2 | CAN_TSTAT_MTFNERR2 | CAN_TSTAT_TME2); + break; + default: + val = CAN_TRANSMIT_FAILED; + break; + } + + switch(val){ + /* transmit pending */ + case (CAN_STATE_PENDING): + state = CAN_TRANSMIT_PENDING; + break; + /* mailbox0 transmit succeeded */ + case (CAN_TSTAT_MTF0 | CAN_TSTAT_MTFNERR0 | CAN_TSTAT_TME0): + state = CAN_TRANSMIT_OK; + break; + /* mailbox1 transmit succeeded */ + case (CAN_TSTAT_MTF1 | CAN_TSTAT_MTFNERR1 | CAN_TSTAT_TME1): + state = CAN_TRANSMIT_OK; + break; + /* mailbox2 transmit succeeded */ + case (CAN_TSTAT_MTF2 | CAN_TSTAT_MTFNERR2 | CAN_TSTAT_TME2): + state = CAN_TRANSMIT_OK; + break; + /* transmit failed */ + default: + state = CAN_TRANSMIT_FAILED; + break; + } + return state; +} + +/*! + \brief stop CAN transmission + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] mailbox_number + only one parameter can be selected which is shown as below: + \arg CAN_MAILBOXx(x=0,1,2) + \param[out] none + \retval none +*/ +void can_transmission_stop(uint32_t can_periph, uint8_t mailbox_number) +{ + if(CAN_MAILBOX0 == mailbox_number){ + CAN_TSTAT(can_periph) |= CAN_TSTAT_MST0; + while(CAN_TSTAT_MST0 == (CAN_TSTAT(can_periph) & CAN_TSTAT_MST0)){ + } + }else if(CAN_MAILBOX1 == mailbox_number){ + CAN_TSTAT(can_periph) |= CAN_TSTAT_MST1; + while(CAN_TSTAT_MST1 == (CAN_TSTAT(can_periph) & CAN_TSTAT_MST1)){ + } + }else if(CAN_MAILBOX2 == mailbox_number){ + CAN_TSTAT(can_periph) |= CAN_TSTAT_MST2; + while(CAN_TSTAT_MST2 == (CAN_TSTAT(can_periph) & CAN_TSTAT_MST2)){ + } + }else{ + /* illegal parameters */ + } +} + +/*! + \brief CAN receive message + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] fifo_number + \arg CAN_FIFOx(x=0,1) + \param[out] receive_message: struct for CAN receive message + \arg rx_sfid: 0x00000000 - 0x000007FF + \arg rx_efid: 0x00000000 - 0x1FFFFFFF + \arg rx_ff: CAN_FF_STANDARD, CAN_FF_EXTENDED + \arg rx_ft: CAN_FT_DATA, CAN_FT_REMOTE + \arg rx_dlenc: 1 - 7 + \arg rx_data[]: 0x00 - 0xFF + \arg rx_fi: 0 - 27 + \retval none +*/ +void can_message_receive(uint32_t can_periph, uint8_t fifo_number, can_receive_message_struct* receive_message) +{ + /* get the frame format */ + receive_message->rx_ff = (uint8_t)(CAN_RFIFOMI_FF & CAN_RFIFOMI(can_periph, fifo_number)); + if(CAN_FF_STANDARD == receive_message->rx_ff){ + /* get standard identifier */ + receive_message->rx_sfid = (uint32_t)(GET_RFIFOMI_SFID(CAN_RFIFOMI(can_periph, fifo_number))); + }else{ + /* get extended identifier */ + receive_message->rx_efid = (uint32_t)(GET_RFIFOMI_EFID(CAN_RFIFOMI(can_periph, fifo_number))); + } + + /* get frame type */ + receive_message->rx_ft = (uint8_t)(CAN_RFIFOMI_FT & CAN_RFIFOMI(can_periph, fifo_number)); + /* filtering index */ + receive_message->rx_fi = (uint8_t)(GET_RFIFOMP_FI(CAN_RFIFOMP(can_periph, fifo_number))); + /* get recevie data length */ + receive_message->rx_dlen = (uint8_t)(GET_RFIFOMP_DLENC(CAN_RFIFOMP(can_periph, fifo_number))); + + /* receive data */ + receive_message -> rx_data[0] = (uint8_t)(GET_RFIFOMDATA0_DB0(CAN_RFIFOMDATA0(can_periph, fifo_number))); + receive_message -> rx_data[1] = (uint8_t)(GET_RFIFOMDATA0_DB1(CAN_RFIFOMDATA0(can_periph, fifo_number))); + receive_message -> rx_data[2] = (uint8_t)(GET_RFIFOMDATA0_DB2(CAN_RFIFOMDATA0(can_periph, fifo_number))); + receive_message -> rx_data[3] = (uint8_t)(GET_RFIFOMDATA0_DB3(CAN_RFIFOMDATA0(can_periph, fifo_number))); + receive_message -> rx_data[4] = (uint8_t)(GET_RFIFOMDATA1_DB4(CAN_RFIFOMDATA1(can_periph, fifo_number))); + receive_message -> rx_data[5] = (uint8_t)(GET_RFIFOMDATA1_DB5(CAN_RFIFOMDATA1(can_periph, fifo_number))); + receive_message -> rx_data[6] = (uint8_t)(GET_RFIFOMDATA1_DB6(CAN_RFIFOMDATA1(can_periph, fifo_number))); + receive_message -> rx_data[7] = (uint8_t)(GET_RFIFOMDATA1_DB7(CAN_RFIFOMDATA1(can_periph, fifo_number))); + + /* release FIFO */ + if(CAN_FIFO0 == fifo_number){ + CAN_RFIFO0(can_periph) |= CAN_RFIFO0_RFD0; + }else{ + CAN_RFIFO1(can_periph) |= CAN_RFIFO1_RFD1; + } +} + +/*! + \brief release FIFO0 + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] fifo_number + only one parameter can be selected which is shown as below: + \arg CAN_FIFOx(x=0,1) + \param[out] none + \retval none +*/ +void can_fifo_release(uint32_t can_periph, uint8_t fifo_number) +{ + if(CAN_FIFO0 == fifo_number){ + CAN_RFIFO0(can_periph) |= CAN_RFIFO0_RFD0; + }else if(CAN_FIFO1 == fifo_number){ + CAN_RFIFO1(can_periph) |= CAN_RFIFO1_RFD1; + }else{ + /* illegal parameters */ + CAN_ERROR_HANDLE("CAN FIFO NUM is invalid \r\n"); + } +} + +/*! + \brief CAN receive message length + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] fifo_number + only one parameter can be selected which is shown as below: + \arg CAN_FIFOx(x=0,1) + \param[out] none + \retval message length +*/ +uint8_t can_receive_message_length_get(uint32_t can_periph, uint8_t fifo_number) +{ + uint8_t val = 0U; + + if(CAN_FIFO0 == fifo_number){ + /* FIFO0 */ + val = (uint8_t)(CAN_RFIFO0(can_periph) & CAN_RFIF_RFL_MASK); + }else if(CAN_FIFO1 == fifo_number){ + /* FIFO1 */ + val = (uint8_t)(CAN_RFIFO1(can_periph) & CAN_RFIF_RFL_MASK); + }else{ + /* illegal parameters */ + } + return val; +} + +/*! + \brief set CAN working mode + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] can_working_mode + only one parameter can be selected which is shown as below: + \arg CAN_MODE_INITIALIZE + \arg CAN_MODE_NORMAL + \arg CAN_MODE_SLEEP + \param[out] none + \retval ErrStatus: SUCCESS or ERROR +*/ +ErrStatus can_working_mode_set(uint32_t can_periph, uint8_t working_mode) +{ + ErrStatus flag = ERROR; + /* timeout for IWS or also for SLPWS bits */ + uint32_t timeout = CAN_TIMEOUT; + + if(CAN_MODE_INITIALIZE == working_mode){ + /* disable sleep mode */ + CAN_CTL(can_periph) &= (~(uint32_t)CAN_CTL_SLPWMOD); + /* set initialize mode */ + CAN_CTL(can_periph) |= (uint8_t)CAN_CTL_IWMOD; + /* wait the acknowledge */ + while((CAN_STAT_IWS != (CAN_STAT(can_periph) & CAN_STAT_IWS)) && (0U != timeout)){ + timeout--; + } + if(CAN_STAT_IWS != (CAN_STAT(can_periph) & CAN_STAT_IWS)){ + flag = ERROR; + }else{ + flag = SUCCESS; + } + }else if(CAN_MODE_NORMAL == working_mode){ + /* enter normal mode */ + CAN_CTL(can_periph) &= ~(uint32_t)(CAN_CTL_SLPWMOD | CAN_CTL_IWMOD); + /* wait the acknowledge */ + while((0U != (CAN_STAT(can_periph) & (CAN_STAT_IWS | CAN_STAT_SLPWS))) && (0U != timeout)){ + timeout--; + } + if(0U != (CAN_STAT(can_periph) & (CAN_STAT_IWS | CAN_STAT_SLPWS))){ + flag = ERROR; + }else{ + flag = SUCCESS; + } + }else if(CAN_MODE_SLEEP == working_mode){ + /* disable initialize mode */ + CAN_CTL(can_periph) &= (~(uint32_t)CAN_CTL_IWMOD); + /* set sleep mode */ + CAN_CTL(can_periph) |= (uint8_t)CAN_CTL_SLPWMOD; + /* wait the acknowledge */ + while((CAN_STAT_SLPWS != (CAN_STAT(can_periph) & CAN_STAT_SLPWS)) && (0U != timeout)){ + timeout--; + } + if(CAN_STAT_SLPWS != (CAN_STAT(can_periph) & CAN_STAT_SLPWS)){ + flag = ERROR; + }else{ + flag = SUCCESS; + } + }else{ + flag = ERROR; + } + return flag; +} + +/*! + \brief wake up CAN + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval ErrStatus: SUCCESS or ERROR +*/ +ErrStatus can_wakeup(uint32_t can_periph) +{ + ErrStatus flag = ERROR; + uint32_t timeout = CAN_TIMEOUT; + + /* wakeup */ + CAN_CTL(can_periph) &= ~CAN_CTL_SLPWMOD; + + while((0U != (CAN_STAT(can_periph) & CAN_STAT_SLPWS)) && (0x00U != timeout)){ + timeout--; + } + /* check state */ + if(0U != (CAN_STAT(can_periph) & CAN_STAT_SLPWS)){ + flag = ERROR; + }else{ + flag = SUCCESS; + } + return flag; +} + +/*! + \brief get CAN error type + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval can_error_enum + \arg CAN_ERROR_NONE: no error + \arg CAN_ERROR_FILL: fill error + \arg CAN_ERROR_FORMATE: format error + \arg CAN_ERROR_ACK: ACK error + \arg CAN_ERROR_BITRECESSIVE: bit recessive + \arg CAN_ERROR_BITDOMINANTER: bit dominant error + \arg CAN_ERROR_CRC: CRC error + \arg CAN_ERROR_SOFTWARECFG: software configure +*/ +can_error_enum can_error_get(uint32_t can_periph) +{ + can_error_enum error; + error = CAN_ERROR_NONE; + + /* get error type */ + error = (can_error_enum)(GET_ERR_ERRN(CAN_ERR(can_periph))); + return error; +} + +/*! + \brief get CAN receive error number + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval error number +*/ +uint8_t can_receive_error_number_get(uint32_t can_periph) +{ + uint8_t val; + + /* get error count */ + val = (uint8_t)(GET_ERR_RECNT(CAN_ERR(can_periph))); + return val; +} + +/*! + \brief get CAN transmit error number + \param[in] can_periph + \arg CANx(x=0,1) + \param[out] none + \retval error number +*/ +uint8_t can_transmit_error_number_get(uint32_t can_periph) +{ + uint8_t val; + + val = (uint8_t)(GET_ERR_TECNT(CAN_ERR(can_periph))); + return val; +} + +/*! + \brief enable CAN interrupt + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] interrupt + one or more parameters can be selected which are shown as below: + \arg CAN_INT_TME: transmit mailbox empty interrupt enable + \arg CAN_INT_RFNE0: receive FIFO0 not empty interrupt enable + \arg CAN_INT_RFF0: receive FIFO0 full interrupt enable + \arg CAN_INT_RFO0: receive FIFO0 overfull interrupt enable + \arg CAN_INT_RFNE1: receive FIFO1 not empty interrupt enable + \arg CAN_INT_RFF1: receive FIFO1 full interrupt enable + \arg CAN_INT_RFO1: receive FIFO1 overfull interrupt enable + \arg CAN_INT_WERR: warning error interrupt enable + \arg CAN_INT_PERR: passive error interrupt enable + \arg CAN_INT_BO: bus-off interrupt enable + \arg CAN_INT_ERRN: error number interrupt enable + \arg CAN_INT_ERR: error interrupt enable + \arg CAN_INT_WU: wakeup interrupt enable + \arg CAN_INT_SLPW: sleep working interrupt enable + \param[out] none + \retval none +*/ +void can_interrupt_enable(uint32_t can_periph, uint32_t interrupt) +{ + CAN_INTEN(can_periph) |= interrupt; +} + +/*! + \brief disable CAN interrupt + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] interrupt + one or more parameters can be selected which are shown as below: + \arg CAN_INT_TME: transmit mailbox empty interrupt enable + \arg CAN_INT_RFNE0: receive FIFO0 not empty interrupt enable + \arg CAN_INT_RFF0: receive FIFO0 full interrupt enable + \arg CAN_INT_RFO0: receive FIFO0 overfull interrupt enable + \arg CAN_INT_RFNE1: receive FIFO1 not empty interrupt enable + \arg CAN_INT_RFF1: receive FIFO1 full interrupt enable + \arg CAN_INT_RFO1: receive FIFO1 overfull interrupt enable + \arg CAN_INT_WERR: warning error interrupt enable + \arg CAN_INT_PERR: passive error interrupt enable + \arg CAN_INT_BO: bus-off interrupt enable + \arg CAN_INT_ERRN: error number interrupt enable + \arg CAN_INT_ERR: error interrupt enable + \arg CAN_INT_WU: wakeup interrupt enable + \arg CAN_INT_SLPW: sleep working interrupt enable + \param[out] none + \retval none +*/ +void can_interrupt_disable(uint32_t can_periph, uint32_t interrupt) +{ + CAN_INTEN(can_periph) &= ~interrupt; +} + +/*! + \brief get CAN flag state + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] flag: CAN flags, refer to can_flag_enum + only one parameter can be selected which is shown as below: + \arg CAN_FLAG_MTE2: mailbox 2 transmit error + \arg CAN_FLAG_MTE1: mailbox 1 transmit error + \arg CAN_FLAG_MTE0: mailbox 0 transmit error + \arg CAN_FLAG_MTF2: mailbox 2 transmit finished + \arg CAN_FLAG_MTF1: mailbox 1 transmit finished + \arg CAN_FLAG_MTF0: mailbox 0 transmit finished + \arg CAN_FLAG_RFO0: receive FIFO0 overfull + \arg CAN_FLAG_RFF0: receive FIFO0 full + \arg CAN_FLAG_RFO1: receive FIFO1 overfull + \arg CAN_FLAG_RFF1: receive FIFO1 full + \arg CAN_FLAG_BOERR: bus-off error + \arg CAN_FLAG_PERR: passive error + \arg CAN_FLAG_WERR: warning error + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus can_flag_get(uint32_t can_periph, can_flag_enum flag) +{ + /* get flag and interrupt enable state */ + if(RESET != (CAN_REG_VAL(can_periph, flag) & BIT(CAN_BIT_POS(flag)))){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear CAN flag state + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] flag: CAN flags, refer to can_flag_enum + only one parameter can be selected which is shown as below: + \arg CAN_FLAG_MTE2: mailbox 2 transmit error + \arg CAN_FLAG_MTE1: mailbox 1 transmit error + \arg CAN_FLAG_MTE0: mailbox 0 transmit error + \arg CAN_FLAG_MTF2: mailbox 2 transmit finished + \arg CAN_FLAG_MTF1: mailbox 1 transmit finished + \arg CAN_FLAG_MTF0: mailbox 0 transmit finished + \arg CAN_FLAG_RFO0: receive FIFO0 overfull + \arg CAN_FLAG_RFF0: receive FIFO0 full + \arg CAN_FLAG_RFO1: receive FIFO1 overfull + \arg CAN_FLAG_RFF1: receive FIFO1 full + \arg CAN_FLAG_BOERR: bus-off error + \arg CAN_FLAG_PERR: passive error + \arg CAN_FLAG_WERR: warning error + \param[out] none + \retval none +*/ +void can_flag_clear(uint32_t can_periph, can_flag_enum flag) +{ + CAN_REG_VAL(can_periph, flag) = BIT(CAN_BIT_POS(flag)); +} + +/*! + \brief get CAN interrupt flag state + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] flag: CAN interrupt flags, refer to can_interrupt_flag_enum + only one parameter can be selected which is shown as below: + \arg CAN_INT_FLAG_SLPIF: status change interrupt flag of sleep working mode entering + \arg CAN_INT_FLAG_WUIF: status change interrupt flag of wakeup from sleep working mode + \arg CAN_INT_FLAG_ERRIF: error interrupt flag + \arg CAN_INT_FLAG_MTF2: mailbox 2 transmit finished interrupt flag + \arg CAN_INT_FLAG_MTF1: mailbox 1 transmit finished interrupt flag + \arg CAN_INT_FLAG_MTF0: mailbox 0 transmit finished interrupt flag + \arg CAN_INT_FLAG_RFO0: receive FIFO0 overfull interrupt flag + \arg CAN_INT_FLAG_RFF0: receive FIFO0 full interrupt flag + \arg CAN_INT_FLAG_RFO1: receive FIFO1 overfull interrupt flag + \arg CAN_INT_FLAG_RFF1: receive FIFO1 full interrupt flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus can_interrupt_flag_get(uint32_t can_periph, can_interrupt_flag_enum flag) +{ + uint32_t ret1 = RESET; + uint32_t ret2 = RESET; + + /* get the staus of interrupt flag */ + ret1 = CAN_REG_VALS(can_periph, flag) & BIT(CAN_BIT_POS0(flag)); + /* get the staus of interrupt enale bit */ + ret2 = CAN_INTEN(can_periph) & BIT(CAN_BIT_POS1(flag)); + if(ret1 && ret2){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear CAN interrupt flag state + \param[in] can_periph + \arg CANx(x=0,1) + \param[in] flag: CAN interrupt flags, refer to can_interrupt_flag_enum + only one parameter can be selected which is shown as below: + \arg CAN_INT_FLAG_SLPIF: status change interrupt flag of sleep working mode entering + \arg CAN_INT_FLAG_WUIF: status change interrupt flag of wakeup from sleep working mode + \arg CAN_INT_FLAG_ERRIF: error interrupt flag + \arg CAN_INT_FLAG_MTF2: mailbox 2 transmit finished interrupt flag + \arg CAN_INT_FLAG_MTF1: mailbox 1 transmit finished interrupt flag + \arg CAN_INT_FLAG_MTF0: mailbox 0 transmit finished interrupt flag + \arg CAN_INT_FLAG_RFO0: receive FIFO0 overfull interrupt flag + \arg CAN_INT_FLAG_RFF0: receive FIFO0 full interrupt flag + \arg CAN_INT_FLAG_RFO1: receive FIFO1 overfull interrupt flag + \arg CAN_INT_FLAG_RFF1: receive FIFO1 full interrupt flag + \arg CAN_FLAG_BOERR: bus-off error + \arg CAN_FLAG_PERR: passive error + \arg CAN_FLAG_WERR: warning error + \param[out] none + \retval none +*/ +void can_interrupt_flag_clear(uint32_t can_periph, can_interrupt_flag_enum flag) +{ + CAN_REG_VALS(can_periph, flag) = BIT(CAN_BIT_POS0(flag)); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_crc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_crc.c new file mode 100644 index 00000000..5753485a --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_crc.c @@ -0,0 +1,127 @@ +/*! + \file gd32vf103_crc.c + \brief CRC driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_crc.h" + +#define CRC_DATA_RESET_VALUE ((uint32_t)0xFFFFFFFFU) +#define CRC_FDATA_RESET_VALUE ((uint32_t)0x00000000U) + +/*! + \brief deinit CRC calculation unit + \param[in] none + \param[out] none + \retval none +*/ +void crc_deinit(void) +{ + CRC_DATA = CRC_DATA_RESET_VALUE; + CRC_FDATA = CRC_FDATA_RESET_VALUE; + CRC_CTL = (uint32_t)CRC_CTL_RST; +} + +/*! + \brief reset data register(CRC_DATA) to the value of 0xFFFFFFFF + \param[in] none + \param[out] none + \retval none +*/ +void crc_data_register_reset(void) +{ + CRC_CTL |= (uint32_t)CRC_CTL_RST; +} + +/*! + \brief read the value of the data register + \param[in] none + \param[out] none + \retval 32-bit value of the data register +*/ +uint32_t crc_data_register_read(void) +{ + uint32_t data; + data = CRC_DATA; + return (data); +} + +/*! + \brief read the value of the free data register + \param[in] none + \param[out] none + \retval 8-bit value of the free data register +*/ +uint8_t crc_free_data_register_read(void) +{ + uint8_t fdata; + fdata = (uint8_t)CRC_FDATA; + return (fdata); +} + +/*! + \brief write data to the free data register + \param[in] free_data: specified 8-bit data + \param[out] none + \retval none +*/ +void crc_free_data_register_write(uint8_t free_data) +{ + CRC_FDATA = (uint32_t)free_data; +} + +/*! + \brief calculate the CRC value of a 32-bit data + \param[in] sdata: specified 32-bit data + \param[out] none + \retval 32-bit value calculated by CRC +*/ +uint32_t crc_single_data_calculate(uint32_t sdata) +{ + CRC_DATA = sdata; + return (CRC_DATA); +} + +/*! + \brief calculate the CRC value of an array of 32-bit values + \param[in] array: pointer to an array of 32-bit values + \param[in] size: size of the array + \param[out] none + \retval 32-bit value calculated by CRC +*/ +uint32_t crc_block_data_calculate(uint32_t array[], uint32_t size) +{ + uint32_t index; + for(index = 0U; index < size; index++){ + CRC_DATA = array[index]; + } + return (CRC_DATA); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dac.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dac.c new file mode 100644 index 00000000..4ec51bf9 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dac.c @@ -0,0 +1,537 @@ +/*! + \file gd32vf103_dac.c + \brief DAC driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_dac.h" + +/* DAC register bit offset */ +#define DAC1_REG_OFFSET ((uint32_t)16U) +#define DH_12BIT_OFFSET ((uint32_t)16U) +#define DH_8BIT_OFFSET ((uint32_t)8U) + +/*! + \brief deinitialize DAC + \param[in] none + \param[out] none + \retval none +*/ +void dac_deinit(void) +{ + rcu_periph_reset_enable(RCU_DACRST); + rcu_periph_reset_disable(RCU_DACRST); +} + +/*! + \brief enable DAC + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_enable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL |= DAC_CTL_DEN0; + }else{ + DAC_CTL |= DAC_CTL_DEN1; + } +} + +/*! + \brief disable DAC + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_disable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL &= ~DAC_CTL_DEN0; + }else{ + DAC_CTL &= ~DAC_CTL_DEN1; + } +} + +/*! + \brief enable DAC DMA function + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_dma_enable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL |= DAC_CTL_DDMAEN0; + }else{ + DAC_CTL |= DAC_CTL_DDMAEN1; + } +} + +/*! + \brief disable DAC DMA function + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_dma_disable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL &= ~DAC_CTL_DDMAEN0; + }else{ + DAC_CTL &= ~DAC_CTL_DDMAEN1; + } +} + +/*! + \brief enable DAC output buffer + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_output_buffer_enable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL &= ~DAC_CTL_DBOFF0; + }else{ + DAC_CTL &= ~DAC_CTL_DBOFF1; + } +} + +/*! + \brief disable DAC output buffer + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_output_buffer_disable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL |= DAC_CTL_DBOFF0; + }else{ + DAC_CTL |= DAC_CTL_DBOFF1; + } +} + +/*! + \brief get DAC output value + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval DAC output data +*/ +uint16_t dac_output_value_get(uint32_t dac_periph) +{ + uint16_t data = 0U; + if(DAC0 == dac_periph){ + /* store the DAC0 output value */ + data = (uint16_t)DAC0_DO; + }else{ + /* store the DAC1 output value */ + data = (uint16_t)DAC1_DO; + } + return data; +} + +/*! + \brief set the DAC specified data holding register value + \param[in] dac_periph: DACx(x = 0,1) + \param[in] dac_align: data alignment + only one parameter can be selected which is shown as below: + \arg DAC_ALIGN_8B_R: data right 8 bit alignment + \arg DAC_ALIGN_12B_R: data right 12 bit alignment + \arg DAC_ALIGN_12B_L: data left 12 bit alignment + \param[in] data: data to be loaded + \param[out] none + \retval none +*/ +void dac_data_set(uint32_t dac_periph, uint32_t dac_align, uint16_t data) +{ + if(DAC0 == dac_periph){ + switch(dac_align){ + /* data right 12 bit alignment */ + case DAC_ALIGN_12B_R: + DAC0_R12DH = data; + break; + /* data left 12 bit alignment */ + case DAC_ALIGN_12B_L: + DAC0_L12DH = data; + break; + /* data right 8 bit alignment */ + case DAC_ALIGN_8B_R: + DAC0_R8DH = data; + break; + default: + break; + } + }else{ + switch(dac_align){ + /* data right 12 bit alignment */ + case DAC_ALIGN_12B_R: + DAC1_R12DH = data; + break; + /* data left 12 bit alignment */ + case DAC_ALIGN_12B_L: + DAC1_L12DH = data; + break; + /* data right 8 bit alignment */ + case DAC_ALIGN_8B_R: + DAC1_R8DH = data; + break; + default: + break; + } + } +} + +/*! + \brief enable DAC trigger + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_trigger_enable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL |= DAC_CTL_DTEN0; + }else{ + DAC_CTL |= DAC_CTL_DTEN1; + } +} + +/*! + \brief disable DAC trigger + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_trigger_disable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_CTL &= ~DAC_CTL_DTEN0; + }else{ + DAC_CTL &= ~DAC_CTL_DTEN1; + } +} + +/*! + \brief set DAC trigger source + \param[in] dac_periph: DACx(x = 0,1) + \param[in] triggersource: external triggers of DAC + only one parameter can be selected which is shown as below: + \arg DAC_TRIGGER_T1_TRGO: TIMER1 TRGO + \arg DAC_TRIGGER_T2_TRGO: TIMER2 TRGO + \arg DAC_TRIGGER_T3_TRGO: TIMER3 TRGO + \arg DAC_TRIGGER_T4_TRGO: TIMER4 TRGO + \arg DAC_TRIGGER_T5_TRGO: TIMER5 TRGO + \arg DAC_TRIGGER_T6_TRGO: TIMER6 TRGO + \arg DAC_TRIGGER_EXTI_9: EXTI interrupt line9 event + \arg DAC_TRIGGER_SOFTWARE: software trigger + \param[out] none + \retval none +*/ +void dac_trigger_source_config(uint32_t dac_periph,uint32_t triggersource) +{ + if(DAC0 == dac_periph){ + /* configure DAC0 trigger source */ + DAC_CTL &= ~DAC_CTL_DTSEL0; + DAC_CTL |= triggersource; + }else{ + /* configure DAC1 trigger source */ + DAC_CTL &= ~DAC_CTL_DTSEL1; + DAC_CTL |= (triggersource << DAC1_REG_OFFSET); + } +} + +/*! + \brief enable DAC software trigger + \param[in] dac_periph: DACx(x = 0,1) + \retval none +*/ +void dac_software_trigger_enable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_SWT |= DAC_SWT_SWTR0; + }else{ + DAC_SWT |= DAC_SWT_SWTR1; + } +} + +/*! + \brief disable DAC software trigger + \param[in] dac_periph: DACx(x = 0,1) + \param[out] none + \retval none +*/ +void dac_software_trigger_disable(uint32_t dac_periph) +{ + if(DAC0 == dac_periph){ + DAC_SWT &= ~DAC_SWT_SWTR0; + }else{ + DAC_SWT &= ~DAC_SWT_SWTR1; + } +} + +/*! + \brief configure DAC wave mode + \param[in] dac_periph: DACx(x = 0,1) + \param[in] wave_mode: noise wave mode + only one parameter can be selected which is shown as below: + \arg DAC_WAVE_DISABLE: wave disable + \arg DAC_WAVE_MODE_LFSR: LFSR noise mode + \arg DAC_WAVE_MODE_TRIANGLE: triangle noise mode + \param[out] none + \retval none +*/ +void dac_wave_mode_config(uint32_t dac_periph, uint32_t wave_mode) +{ + if(DAC0 == dac_periph){ + /* configure DAC0 wave mode */ + DAC_CTL &= ~DAC_CTL_DWM0; + DAC_CTL |= wave_mode; + }else{ + /* configure DAC1 wave mode */ + DAC_CTL &= ~DAC_CTL_DWM1; + DAC_CTL |= (wave_mode << DAC1_REG_OFFSET); + } +} + +/*! + \brief configure DAC wave bit width + \param[in] dac_periph: DACx(x = 0,1) + \param[in] bit_width: noise wave bit width + only one parameter can be selected which is shown as below: + \arg DAC_WAVE_BIT_WIDTH_1: bit width of the wave signal is 1 + \arg DAC_WAVE_BIT_WIDTH_2: bit width of the wave signal is 2 + \arg DAC_WAVE_BIT_WIDTH_3: bit width of the wave signal is 3 + \arg DAC_WAVE_BIT_WIDTH_4: bit width of the wave signal is 4 + \arg DAC_WAVE_BIT_WIDTH_5: bit width of the wave signal is 5 + \arg DAC_WAVE_BIT_WIDTH_6: bit width of the wave signal is 6 + \arg DAC_WAVE_BIT_WIDTH_7: bit width of the wave signal is 7 + \arg DAC_WAVE_BIT_WIDTH_8: bit width of the wave signal is 8 + \arg DAC_WAVE_BIT_WIDTH_9: bit width of the wave signal is 9 + \arg DAC_WAVE_BIT_WIDTH_10: bit width of the wave signal is 10 + \arg DAC_WAVE_BIT_WIDTH_11: bit width of the wave signal is 11 + \arg DAC_WAVE_BIT_WIDTH_12: bit width of the wave signal is 12 + \param[out] none + \retval none +*/ +void dac_wave_bit_width_config(uint32_t dac_periph, uint32_t bit_width) +{ + if(DAC0 == dac_periph){ + /* configure DAC0 wave bit width */ + DAC_CTL &= ~DAC_CTL_DWBW0; + DAC_CTL |= bit_width; + }else{ + /* configure DAC1 wave bit width */ + DAC_CTL &= ~DAC_CTL_DWBW1; + DAC_CTL |= (bit_width << DAC1_REG_OFFSET); + } +} + +/*! + \brief configure DAC LFSR noise mode + \param[in] dac_periph: DACx(x = 0,1) + \param[in] unmask_bits: unmask LFSR bits in DAC LFSR noise mode + only one parameter can be selected which is shown as below: + \arg DAC_LFSR_BIT0: unmask the LFSR bit0 + \arg DAC_LFSR_BITS1_0: unmask the LFSR bits[1:0] + \arg DAC_LFSR_BITS2_0: unmask the LFSR bits[2:0] + \arg DAC_LFSR_BITS3_0: unmask the LFSR bits[3:0] + \arg DAC_LFSR_BITS4_0: unmask the LFSR bits[4:0] + \arg DAC_LFSR_BITS5_0: unmask the LFSR bits[5:0] + \arg DAC_LFSR_BITS6_0: unmask the LFSR bits[6:0] + \arg DAC_LFSR_BITS7_0: unmask the LFSR bits[7:0] + \arg DAC_LFSR_BITS8_0: unmask the LFSR bits[8:0] + \arg DAC_LFSR_BITS9_0: unmask the LFSR bits[9:0] + \arg DAC_LFSR_BITS10_0: unmask the LFSR bits[10:0] + \arg DAC_LFSR_BITS11_0: unmask the LFSR bits[11:0] + \param[out] none + \retval none +*/ +void dac_lfsr_noise_config(uint32_t dac_periph, uint32_t unmask_bits) +{ + if(DAC0 == dac_periph){ + /* configure DAC0 LFSR noise mode */ + DAC_CTL &= ~DAC_CTL_DWBW0; + DAC_CTL |= unmask_bits; + }else{ + /* configure DAC1 LFSR noise mode */ + DAC_CTL &= ~DAC_CTL_DWBW1; + DAC_CTL |= (unmask_bits << DAC1_REG_OFFSET); + } +} + +/*! + \brief configure DAC triangle noise mode + \param[in] dac_periph: DACx(x = 0,1) + \param[in] amplitude: triangle amplitude in DAC triangle noise mode + only one parameter can be selected which is shown as below: + \arg DAC_TRIANGLE_AMPLITUDE_1: triangle amplitude is 1 + \arg DAC_TRIANGLE_AMPLITUDE_3: triangle amplitude is 3 + \arg DAC_TRIANGLE_AMPLITUDE_7: triangle amplitude is 7 + \arg DAC_TRIANGLE_AMPLITUDE_15: triangle amplitude is 15 + \arg DAC_TRIANGLE_AMPLITUDE_31: triangle amplitude is 31 + \arg DAC_TRIANGLE_AMPLITUDE_63: triangle amplitude is 63 + \arg DAC_TRIANGLE_AMPLITUDE_127: triangle amplitude is 127 + \arg DAC_TRIANGLE_AMPLITUDE_255: triangle amplitude is 255 + \arg DAC_TRIANGLE_AMPLITUDE_511: triangle amplitude is 511 + \arg DAC_TRIANGLE_AMPLITUDE_1023: triangle amplitude is 1023 + \arg DAC_TRIANGLE_AMPLITUDE_2047: triangle amplitude is 2047 + \arg DAC_TRIANGLE_AMPLITUDE_4095: triangle amplitude is 4095 + \param[out] none + \retval none +*/ +void dac_triangle_noise_config(uint32_t dac_periph, uint32_t amplitude) +{ + if(DAC0 == dac_periph){ + /* configure DAC0 triangle noise mode */ + DAC_CTL &= ~DAC_CTL_DWBW0; + DAC_CTL |= amplitude; + }else{ + /* configure DAC1 triangle noise mode */ + DAC_CTL &= ~DAC_CTL_DWBW1; + DAC_CTL |= (amplitude << DAC1_REG_OFFSET); + } +} + +/*! + \brief enable DAC concurrent mode + \param[in] none + \param[out] none + \retval none +*/ +void dac_concurrent_enable(void) +{ + uint32_t ctl = 0U; + ctl = DAC_CTL_DEN0 | DAC_CTL_DEN1; + DAC_CTL |= (ctl); +} + +/*! + \brief disable DAC concurrent mode + \param[in] none + \param[out] none + \retval none +*/ +void dac_concurrent_disable(void) +{ + uint32_t ctl = 0U; + ctl = DAC_CTL_DEN0 | DAC_CTL_DEN1; + DAC_CTL &= (~ctl); +} + +/*! + \brief enable DAC concurrent software trigger function + \param[in] none + \param[out] none + \retval none +*/ +void dac_concurrent_software_trigger_enable(void) +{ + uint32_t swt = 0U; + swt = DAC_SWT_SWTR0 | DAC_SWT_SWTR1; + DAC_SWT |= (swt); +} + +/*! + \brief disable DAC concurrent software trigger function + \param[in] none + \param[out] none + \retval none +*/ +void dac_concurrent_software_trigger_disable(void) +{ + uint32_t swt = 0U; + swt = DAC_SWT_SWTR0 | DAC_SWT_SWTR1; + DAC_SWT &= (~swt); +} + +/*! + \brief enable DAC concurrent buffer function + \param[in] none + \param[out] none + \retval none +*/ +void dac_concurrent_output_buffer_enable(void) +{ + uint32_t ctl = 0U; + ctl = DAC_CTL_DBOFF0 | DAC_CTL_DBOFF1; + DAC_CTL &= (~ctl); +} + +/*! + \brief disable DAC concurrent buffer function + \param[in] none + \param[out] none + \retval none +*/ +void dac_concurrent_output_buffer_disable(void) +{ + uint32_t ctl = 0U; + ctl = DAC_CTL_DBOFF0 | DAC_CTL_DBOFF1; + DAC_CTL |= (ctl); +} + +/*! + \brief set DAC concurrent mode data holding register value + \param[in] dac_align: data alignment + only one parameter can be selected which is shown as below: + \arg DAC_ALIGN_8B_R: data right 8b alignment + \arg DAC_ALIGN_12B_R: data right 12b alignment + \arg DAC_ALIGN_12B_L: data left 12b alignment + \param[in] data0: data to be loaded + \param[in] data1: data to be loaded + \param[out] none + \retval none +*/ +void dac_concurrent_data_set(uint32_t dac_align, uint16_t data0, uint16_t data1) +{ + uint32_t data = 0U; + switch(dac_align){ + /* data right 12b alignment */ + case DAC_ALIGN_12B_R: + data = ((uint32_t)data1 << DH_12BIT_OFFSET) | data0; + DACC_R12DH = data; + break; + /* data left 12b alignment */ + case DAC_ALIGN_12B_L: + data = ((uint32_t)data1 << DH_12BIT_OFFSET) | data0; + DACC_L12DH = data; + break; + /* data right 8b alignment */ + case DAC_ALIGN_8B_R: + data = ((uint32_t)data1 << DH_8BIT_OFFSET) | data0; + DACC_R8DH = data; + break; + default: + break; + } +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dbg.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dbg.c new file mode 100644 index 00000000..2e0dfe52 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dbg.c @@ -0,0 +1,110 @@ +/*! + \file gd32vf103_dbg.c + \brief DBG driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_dbg.h" + +/*! + \brief read DBG_ID code register + \param[in] none + \param[out] none + \retval DBG_ID code +*/ +uint32_t dbg_id_get(void) +{ + return DBG_ID; +} + +/*! + \brief enable low power behavior when the mcu is in debug mode + \param[in] dbg_low_power: + one or more parameters can be selected which are shown as below: + \arg DBG_LOW_POWER_SLEEP: keep debugger connection during sleep mode + \arg DBG_LOW_POWER_DEEPSLEEP: keep debugger connection during deepsleep mode + \arg DBG_LOW_POWER_STANDBY: keep debugger connection during standby mode + \param[out] none + \retval none +*/ +void dbg_low_power_enable(uint32_t dbg_low_power) +{ + DBG_CTL |= dbg_low_power; +} + +/*! + \brief disable low power behavior when the mcu is in debug mode + \param[in] dbg_low_power: + one or more parameters can be selected which are shown as below: + \arg DBG_LOW_POWER_SLEEP: donot keep debugger connection during sleep mode + \arg DBG_LOW_POWER_DEEPSLEEP: donot keep debugger connection during deepsleep mode + \arg DBG_LOW_POWER_STANDBY: donot keep debugger connection during standby mode + \param[out] none + \retval none +*/ +void dbg_low_power_disable(uint32_t dbg_low_power) +{ + DBG_CTL &= ~dbg_low_power; +} + +/*! + \brief enable peripheral behavior when the mcu is in debug mode + \param[in] dbg_periph: refer to dbg_periph_enum + one or more parameters can be selected which are shown as below: + \arg DBG_FWDGT_HOLD : debug FWDGT kept when core is halted + \arg DBG_WWDGT_HOLD : debug WWDGT kept when core is halted + \arg DBG_CANx_HOLD (x=0,1): hold CANx counter when core is halted + \arg DBG_I2Cx_HOLD (x=0,1): hold I2Cx smbus when core is halted + \arg DBG_TIMERx_HOLD (x=0,1,2,3,4,5,6): hold TIMERx counter when core is halted + \param[out] none + \retval none +*/ +void dbg_periph_enable(dbg_periph_enum dbg_periph) +{ + DBG_CTL |= (uint32_t)dbg_periph; +} + +/*! + \brief disable peripheral behavior when the mcu is in debug mode + \param[in] dbg_periph: refer to dbg_periph_enum + one or more parameters can be selected which are shown as below: + \arg DBG_FWDGT_HOLD : debug FWDGT kept when core is halted + \arg DBG_WWDGT_HOLD : debug WWDGT kept when core is halted + \arg DBG_CANx_HOLD (x=0,1): hold CAN0 counter when core is halted + \arg DBG_I2Cx_HOLD (x=0,1): hold I2Cx smbus when core is halted + \arg DBG_TIMERx_HOLD (x=0,1,2,3,4,5,6): hold TIMERx counter when core is halted + \param[out] none + \retval none +*/ +void dbg_periph_disable(dbg_periph_enum dbg_periph) +{ + DBG_CTL &= ~(uint32_t)dbg_periph; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dma.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dma.c new file mode 100644 index 00000000..c1ee54fb --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_dma.c @@ -0,0 +1,731 @@ +/*! + \file gd32vf103_dma.c + \brief DMA driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_dma.h" + +#define DMA_WRONG_HANDLE while(1){} + +/* check whether peripheral matches channels or not */ +static ErrStatus dma_periph_and_channel_check(uint32_t dma_periph, dma_channel_enum channelx); + +/*! + \brief deinitialize DMA a channel registers + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel is deinitialized + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_deinit(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + /* disable DMA a channel */ + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_CHEN; + /* reset DMA channel registers */ + DMA_CHCTL(dma_periph, channelx) = DMA_CHCTL_RESET_VALUE; + DMA_CHCNT(dma_periph, channelx) = DMA_CHCNT_RESET_VALUE; + DMA_CHPADDR(dma_periph, channelx) = DMA_CHPADDR_RESET_VALUE; + DMA_CHMADDR(dma_periph, channelx) = DMA_CHMADDR_RESET_VALUE; + DMA_INTC(dma_periph) |= DMA_FLAG_ADD(DMA_CHINTF_RESET_VALUE, channelx); +} + +/*! + \brief initialize the parameters of DMA struct with the default values + \param[in] init_struct: the initialization data needed to initialize DMA channel + \param[out] none + \retval none +*/ +void dma_struct_para_init(dma_parameter_struct* init_struct) +{ + /* set the DMA struct with the default values */ + init_struct->periph_addr = 0U; + init_struct->periph_width = 0U; + init_struct->periph_inc = DMA_PERIPH_INCREASE_DISABLE; + init_struct->memory_addr = 0U; + init_struct->memory_width = 0U; + init_struct->memory_inc = DMA_MEMORY_INCREASE_DISABLE; + init_struct->number = 0U; + init_struct->direction = DMA_PERIPHERAL_TO_MEMORY; + init_struct->priority = DMA_PRIORITY_LOW; +} + +/*! + \brief initialize DMA channel + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel is initialized + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] init_struct: the data needed to initialize DMA channel + periph_addr: peripheral base address + periph_width: DMA_PERIPHERAL_WIDTH_8BIT, DMA_PERIPHERAL_WIDTH_16BIT, DMA_PERIPHERAL_WIDTH_32BIT + periph_inc: DMA_PERIPH_INCREASE_ENABLE, DMA_PERIPH_INCREASE_DISABLE + memory_addr: memory base address + memory_width: DMA_MEMORY_WIDTH_8BIT, DMA_MEMORY_WIDTH_16BIT, DMA_MEMORY_WIDTH_32BIT + memory_inc: DMA_MEMORY_INCREASE_ENABLE, DMA_MEMORY_INCREASE_DISABLE + direction: DMA_PERIPHERAL_TO_MEMORY, DMA_MEMORY_TO_PERIPHERAL + number: the number of remaining data to be transferred by the DMA + priority: DMA_PRIORITY_LOW, DMA_PRIORITY_MEDIUM, DMA_PRIORITY_HIGH, DMA_PRIORITY_ULTRA_HIGH + \param[out] none + \retval none +*/ +void dma_init(uint32_t dma_periph, dma_channel_enum channelx, dma_parameter_struct* init_struct) +{ + uint32_t ctl; + + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + /* configure peripheral base address */ + DMA_CHPADDR(dma_periph, channelx) = init_struct->periph_addr; + + /* configure memory base address */ + DMA_CHMADDR(dma_periph, channelx) = init_struct->memory_addr; + + /* configure the number of remaining data to be transferred */ + DMA_CHCNT(dma_periph, channelx) = (init_struct->number & DMA_CHANNEL_CNT_MASK); + + /* configure peripheral transfer width,memory transfer width and priority */ + ctl = DMA_CHCTL(dma_periph, channelx); + ctl &= ~(DMA_CHXCTL_PWIDTH | DMA_CHXCTL_MWIDTH | DMA_CHXCTL_PRIO); + ctl |= (init_struct->periph_width | init_struct->memory_width | init_struct->priority); + DMA_CHCTL(dma_periph, channelx) = ctl; + + /* configure peripheral increasing mode */ + if(DMA_PERIPH_INCREASE_ENABLE == init_struct->periph_inc){ + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_PNAGA; + }else{ + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_PNAGA; + } + + /* configure memory increasing mode */ + if(DMA_MEMORY_INCREASE_ENABLE == init_struct->memory_inc){ + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_MNAGA; + }else{ + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_MNAGA; + } + + /* configure the direction of data transfer */ + if(DMA_PERIPHERAL_TO_MEMORY == init_struct->direction){ + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_DIR; + }else{ + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_DIR; + } +} + +/*! + \brief enable DMA circulation mode + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_circulation_enable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_CMEN; +} + +/*! + \brief disable DMA circulation mode + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_circulation_disable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_CMEN; +} + +/*! + \brief enable memory to memory mode + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_memory_to_memory_enable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_M2M; +} + +/*! + \brief disable memory to memory mode + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_memory_to_memory_disable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_M2M; +} + +/*! + \brief enable DMA channel + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_channel_enable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_CHEN; +} + +/*! + \brief disable DMA channel + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_channel_disable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_CHEN; +} + +/*! + \brief set DMA peripheral base address + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to set peripheral base address + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] address: peripheral base address + \param[out] none + \retval none +*/ +void dma_periph_address_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t address) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHPADDR(dma_periph, channelx) = address; +} + +/*! + \brief set DMA memory base address + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to set memory base address + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] address: memory base address + \param[out] none + \retval none +*/ +void dma_memory_address_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t address) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHMADDR(dma_periph, channelx) = address; +} + +/*! + \brief set the number of remaining data to be transferred by the DMA + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to set number + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] number: the number of remaining data to be transferred by the DMA + \param[out] none + \retval none +*/ +void dma_transfer_number_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t number) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCNT(dma_periph, channelx) = (number & DMA_CHANNEL_CNT_MASK); +} + +/*! + \brief get the number of remaining data to be transferred by the DMA + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to set number + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval uint32_t: the number of remaining data to be transferred by the DMA +*/ +uint32_t dma_transfer_number_get(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + return (uint32_t)DMA_CHCNT(dma_periph, channelx); +} + +/*! + \brief configure priority level of DMA channel + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] priority: priority Level of this channel + only one parameter can be selected which is shown as below: + \arg DMA_PRIORITY_LOW: low priority + \arg DMA_PRIORITY_MEDIUM: medium priority + \arg DMA_PRIORITY_HIGH: high priority + \arg DMA_PRIORITY_ULTRA_HIGH: ultra high priority + \param[out] none + \retval none +*/ +void dma_priority_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t priority) +{ + uint32_t ctl; + + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + /* acquire DMA_CHxCTL register */ + ctl = DMA_CHCTL(dma_periph, channelx); + /* assign regiser */ + ctl &= ~DMA_CHXCTL_PRIO; + ctl |= priority; + DMA_CHCTL(dma_periph, channelx) = ctl; +} + +/*! + \brief configure transfer data size of memory + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] mwidth: transfer data width of memory + only one parameter can be selected which is shown as below: + \arg DMA_MEMORY_WIDTH_8BIT: transfer data width of memory is 8-bit + \arg DMA_MEMORY_WIDTH_16BIT: transfer data width of memory is 16-bit + \arg DMA_MEMORY_WIDTH_32BIT: transfer data width of memory is 32-bit + \param[out] none + \retval none +*/ +void dma_memory_width_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t mwidth) +{ + uint32_t ctl; + + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + /* acquire DMA_CHxCTL register */ + ctl = DMA_CHCTL(dma_periph, channelx); + /* assign regiser */ + ctl &= ~DMA_CHXCTL_MWIDTH; + ctl |= mwidth; + DMA_CHCTL(dma_periph, channelx) = ctl; +} + +/*! + \brief configure transfer data size of peripheral + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] pwidth: transfer data width of peripheral + only one parameter can be selected which is shown as below: + \arg DMA_PERIPHERAL_WIDTH_8BIT: transfer data width of peripheral is 8-bit + \arg DMA_PERIPHERAL_WIDTH_16BIT: transfer data width of peripheral is 16-bit + \arg DMA_PERIPHERAL_WIDTH_32BIT: transfer data width of peripheral is 32-bit + \param[out] none + \retval none +*/ +void dma_periph_width_config (uint32_t dma_periph, dma_channel_enum channelx, uint32_t pwidth) +{ + uint32_t ctl; + + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + /* acquire DMA_CHxCTL register */ + ctl = DMA_CHCTL(dma_periph, channelx); + /* assign regiser */ + ctl &= ~DMA_CHXCTL_PWIDTH; + ctl |= pwidth; + DMA_CHCTL(dma_periph, channelx) = ctl; +} + +/*! + \brief enable next address increasement algorithm of memory + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_memory_increase_enable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_MNAGA; +} + +/*! + \brief disable next address increasement algorithm of memory + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_memory_increase_disable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_MNAGA; +} + +/*! + \brief enable next address increasement algorithm of peripheral + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_periph_increase_enable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_PNAGA; +} + +/*! + \brief disable next address increasement algorithm of peripheral + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[out] none + \retval none +*/ +void dma_periph_increase_disable(uint32_t dma_periph, dma_channel_enum channelx) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_PNAGA; +} + +/*! + \brief configure the direction of data transfer on the channel + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] direction: specify the direction of data transfer + only one parameter can be selected which is shown as below: + \arg DMA_PERIPHERAL_TO_MEMORY: read from peripheral and write to memory + \arg DMA_MEMORY_TO_PERIPHERAL: read from memory and write to peripheral + \param[out] none + \retval none +*/ +void dma_transfer_direction_config(uint32_t dma_periph, dma_channel_enum channelx, uint32_t direction) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + if(DMA_PERIPHERAL_TO_MEMORY == direction){ + DMA_CHCTL(dma_periph, channelx) &= ~DMA_CHXCTL_DIR; + } else { + DMA_CHCTL(dma_periph, channelx) |= DMA_CHXCTL_DIR; + } +} + +/*! + \brief check DMA flag is set or not + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to get flag + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] flag: specify get which flag + only one parameter can be selected which is shown as below: + \arg DMA_FLAG_G: global interrupt flag of channel + \arg DMA_FLAG_FTF: full transfer finish flag of channel + \arg DMA_FLAG_HTF: half transfer finish flag of channel + \arg DMA_FLAG_ERR: error flag of channel + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus dma_flag_get(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag) +{ + FlagStatus reval; + + if(RESET != (DMA_INTF(dma_periph) & DMA_FLAG_ADD(flag, channelx))){ + reval = SET; + }else{ + reval = RESET; + } + + return reval; +} + +/*! + \brief clear DMA a channel flag + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to clear flag + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] flag: specify get which flag + only one parameter can be selected which is shown as below: + \arg DMA_FLAG_G: global interrupt flag of channel + \arg DMA_FLAG_FTF: full transfer finish flag of channel + \arg DMA_FLAG_HTF: half transfer finish flag of channel + \arg DMA_FLAG_ERR: error flag of channel + \param[out] none + \retval none +*/ +void dma_flag_clear(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag) +{ + DMA_INTC(dma_periph) |= DMA_FLAG_ADD(flag, channelx); +} + +/*! + \brief check DMA flag and interrupt enable bit is set or not + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to get flag + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] flag: specify get which flag + only one parameter can be selected which is shown as below: + \arg DMA_INT_FLAG_FTF: full transfer finish interrupt flag of channel + \arg DMA_INT_FLAG_HTF: half transfer finish interrupt flag of channel + \arg DMA_INT_FLAG_ERR: error interrupt flag of channel + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus dma_interrupt_flag_get(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag) +{ + uint32_t interrupt_enable = 0U, interrupt_flag = 0U; + + switch(flag){ + case DMA_INT_FLAG_FTF: + /* check whether the full transfer finish interrupt flag is set and enabled */ + interrupt_flag = DMA_INTF(dma_periph) & DMA_FLAG_ADD(flag, channelx); + interrupt_enable = DMA_CHCTL(dma_periph, channelx) & DMA_CHXCTL_FTFIE; + break; + case DMA_INT_FLAG_HTF: + /* check whether the half transfer finish interrupt flag is set and enabled */ + interrupt_flag = DMA_INTF(dma_periph) & DMA_FLAG_ADD(flag, channelx); + interrupt_enable = DMA_CHCTL(dma_periph, channelx) & DMA_CHXCTL_HTFIE; + break; + case DMA_INT_FLAG_ERR: + /* check whether the error interrupt flag is set and enabled */ + interrupt_flag = DMA_INTF(dma_periph) & DMA_FLAG_ADD(flag, channelx); + interrupt_enable = DMA_CHCTL(dma_periph, channelx) & DMA_CHXCTL_ERRIE; + break; + default: + DMA_WRONG_HANDLE + } + + /* when the interrupt flag is set and enabled, return SET */ + if(interrupt_flag && interrupt_enable){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear DMA a channel flag + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel to clear flag + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] flag: specify get which flag + only one parameter can be selected which is shown as below: + \arg DMA_INT_FLAG_G: global interrupt flag of channel + \arg DMA_INT_FLAG_FTF: full transfer finish interrupt flag of channel + \arg DMA_INT_FLAG_HTF: half transfer finish interrupt flag of channel + \arg DMA_INT_FLAG_ERR: error interrupt flag of channel + \param[out] none + \retval none +*/ +void dma_interrupt_flag_clear(uint32_t dma_periph, dma_channel_enum channelx, uint32_t flag) +{ + DMA_INTC(dma_periph) |= DMA_FLAG_ADD(flag, channelx); +} + +/*! + \brief enable DMA interrupt + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] source: specify which interrupt to enbale + one or more parameters can be selected which are shown as below + \arg DMA_INT_FTF: channel full transfer finish interrupt + \arg DMA_INT_HTF: channel half transfer finish interrupt + \arg DMA_INT_ERR: channel error interrupt + \param[out] none + \retval none +*/ +void dma_interrupt_enable(uint32_t dma_periph, dma_channel_enum channelx, uint32_t source) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) |= source; +} + +/*! + \brief disable DMA interrupt + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA0: DMA_CHx(x=0..6), DMA1: DMA_CHx(x=0..4) + \param[in] source: specify which interrupt to disbale + one or more parameters can be selected which are shown as below + \arg DMA_INT_FTF: channel full transfer finish interrupt + \arg DMA_INT_HTF: channel half transfer finish interrupt + \arg DMA_INT_ERR: channel error interrupt + \param[out] none + \retval none +*/ +void dma_interrupt_disable(uint32_t dma_periph, dma_channel_enum channelx, uint32_t source) +{ + if(ERROR == dma_periph_and_channel_check(dma_periph, channelx)){ + DMA_WRONG_HANDLE + } + + DMA_CHCTL(dma_periph, channelx) &= ~source; +} + +/*! + \brief check whether peripheral and channels match + \param[in] dma_periph: DMAx(x=0,1) + \arg DMAx(x=0,1) + \param[in] channelx: specify which DMA channel + only one parameter can be selected which is shown as below: + \arg DMA_CHx(x=0..6) + \param[out] none + \retval none +*/ +static ErrStatus dma_periph_and_channel_check(uint32_t dma_periph, dma_channel_enum channelx) +{ + ErrStatus val = SUCCESS; + + if(DMA1 == dma_periph){ + /* for DMA1, the channel is from DMA_CH0 to DMA_CH4 */ + if(channelx > DMA_CH4){ + val = ERROR; + } + } + + return val; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exmc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exmc.c new file mode 100644 index 00000000..d414e078 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exmc.c @@ -0,0 +1,164 @@ +/*! + \file gd32vf103_exmc.c + \brief EXMC driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_exmc.h" + +/* EXMC bank0 register reset value */ +#define BANK0_SNCTL0_REGION_RESET ((uint32_t)0x000030DAU) +#define BANK0_SNTCFG_RESET ((uint32_t)0x0FFFFFFFU) + +/* EXMC register bit offset */ +#define SNCTL_NRMUX_OFFSET ((uint32_t)1U) +#define SNCTL_WREN_OFFSET ((uint32_t)12U) +#define SNCTL_NRWTEN_OFFSET ((uint32_t)13U) +#define SNCTL_ASYNCWAIT_OFFSET ((uint32_t)15U) + +#define SNTCFG_AHLD_OFFSET ((uint32_t)4U) +#define SNTCFG_DSET_OFFSET ((uint32_t)8U) +#define SNTCFG_BUSLAT_OFFSET ((uint32_t)16U) + +/*! + \brief deinitialize EXMC NOR/SRAM region + \param[in] norsram_region: select the region of bank0 + \arg EXMC_BANK0_NORSRAM_REGIONx(x=0) + \param[out] none + \retval none +*/ +void exmc_norsram_deinit(uint32_t norsram_region) +{ + /* reset the registers */ + if(EXMC_BANK0_NORSRAM_REGION0 == norsram_region){ + EXMC_SNCTL(norsram_region) = BANK0_SNCTL0_REGION_RESET; + } + + EXMC_SNTCFG(norsram_region) = BANK0_SNTCFG_RESET; +} + +/*! + \brief initialize the structure exmc_norsram_parameter_struct + \param[in] none + \param[out] exmc_norsram_init_struct: the initialized structure exmc_norsram_parameter_struct pointer + \retval none +*/ +void exmc_norsram_struct_para_init(exmc_norsram_parameter_struct* exmc_norsram_init_struct) +{ + /* configure the structure with default value */ + exmc_norsram_init_struct->norsram_region = EXMC_BANK0_NORSRAM_REGION0; + exmc_norsram_init_struct->address_data_mux = ENABLE; + exmc_norsram_init_struct->memory_type = EXMC_MEMORY_TYPE_SRAM; + exmc_norsram_init_struct->databus_width = EXMC_NOR_DATABUS_WIDTH_16B; + exmc_norsram_init_struct->nwait_polarity = EXMC_NWAIT_POLARITY_LOW; + exmc_norsram_init_struct->memory_write = ENABLE; + exmc_norsram_init_struct->nwait_signal = ENABLE; + exmc_norsram_init_struct->asyn_wait = DISABLE; + + /* read/write timing configure */ + exmc_norsram_init_struct->read_write_timing->asyn_address_setuptime = 0xFU; + exmc_norsram_init_struct->read_write_timing->asyn_address_holdtime = 0xFU; + exmc_norsram_init_struct->read_write_timing->asyn_data_setuptime = 0xFFU; + exmc_norsram_init_struct->read_write_timing->bus_latency = 0xFU; +} + +/*! + \brief initialize EXMC NOR/SRAM region + \param[in] exmc_norsram_parameter_struct: configure the EXMC NOR/SRAM parameter + norsram_region: EXMC_BANK0_NORSRAM_REGIONx,x=0 + asyn_wait: ENABLE or DISABLE + nwait_signal: ENABLE or DISABLE + memory_write: ENABLE or DISABLE + nwait_polarity: EXMC_NWAIT_POLARITY_LOW,EXMC_NWAIT_POLARITY_HIGH + databus_width: EXMC_NOR_DATABUS_WIDTH_8B,EXMC_NOR_DATABUS_WIDTH_16B + memory_type: EXMC_MEMORY_TYPE_SRAM,EXMC_MEMORY_TYPE_PSRAM,EXMC_MEMORY_TYPE_NOR + address_data_mux: ENABLE + read_write_timing: structure exmc_norsram_timing_parameter_struct set the time + \param[out] none + \retval none +*/ +void exmc_norsram_init(exmc_norsram_parameter_struct* exmc_norsram_init_struct) +{ + uint32_t snctl = 0x00000000U, sntcfg = 0x00000000U; + + /* get the register value */ + snctl = EXMC_SNCTL(exmc_norsram_init_struct->norsram_region); + + /* clear relative bits */ + snctl &= ((uint32_t)~(EXMC_SNCTL_NREN | EXMC_SNCTL_NRTP | EXMC_SNCTL_NRW | EXMC_SNCTL_NRWTPOL | + EXMC_SNCTL_WREN | EXMC_SNCTL_NRWTEN | EXMC_SNCTL_ASYNCWAIT | EXMC_SNCTL_NRMUX)); + + snctl |= (uint32_t)(exmc_norsram_init_struct->address_data_mux << SNCTL_NRMUX_OFFSET) | + exmc_norsram_init_struct->memory_type | + exmc_norsram_init_struct->databus_width | + exmc_norsram_init_struct->nwait_polarity | + (exmc_norsram_init_struct->memory_write << SNCTL_WREN_OFFSET) | + (exmc_norsram_init_struct->nwait_signal << SNCTL_NRWTEN_OFFSET) | + (exmc_norsram_init_struct->asyn_wait << SNCTL_ASYNCWAIT_OFFSET); + + sntcfg = (uint32_t)((exmc_norsram_init_struct->read_write_timing->asyn_address_setuptime - 1U ) & EXMC_SNTCFG_ASET )| + (((exmc_norsram_init_struct->read_write_timing->asyn_address_holdtime - 1U ) << SNTCFG_AHLD_OFFSET ) & EXMC_SNTCFG_AHLD ) | + (((exmc_norsram_init_struct->read_write_timing->asyn_data_setuptime - 1U ) << SNTCFG_DSET_OFFSET ) & EXMC_SNTCFG_DSET ) | + (((exmc_norsram_init_struct->read_write_timing->bus_latency - 1U ) << SNTCFG_BUSLAT_OFFSET ) & EXMC_SNTCFG_BUSLAT ); + + /* nor flash access enable */ + if(EXMC_MEMORY_TYPE_NOR == exmc_norsram_init_struct->memory_type){ + snctl |= (uint32_t)EXMC_SNCTL_NREN; + } + + /* configure the registers */ + EXMC_SNCTL(exmc_norsram_init_struct->norsram_region) = snctl; + EXMC_SNTCFG(exmc_norsram_init_struct->norsram_region) = sntcfg; +} + +/*! + \brief enable EXMC NOR/PSRAM bank region + \param[in] norsram_region: specify the region of NOR/PSRAM bank + \arg EXMC_BANK0_NORSRAM_REGIONx(x=0) + \param[out] none + \retval none +*/ +void exmc_norsram_enable(uint32_t norsram_region) +{ + EXMC_SNCTL(norsram_region) |= (uint32_t)EXMC_SNCTL_NRBKEN; +} + +/*! + \brief disable EXMC NOR/PSRAM bank region + \param[in] norsram_region: specify the region of NOR/PSRAM bank + \arg EXMC_BANK0_NORSRAM_REGIONx(x=0) + \param[out] none + \retval none +*/ +void exmc_norsram_disable(uint32_t norsram_region) +{ + EXMC_SNCTL(norsram_region) &= ~(uint32_t)EXMC_SNCTL_NRBKEN; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exti.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exti.c new file mode 100644 index 00000000..ee9ab0c6 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_exti.c @@ -0,0 +1,254 @@ +/*! + \file gd32vf103_exti.c + \brief EXTI driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_exti.h" + +#define EXTI_REG_RESET_VALUE ((uint32_t)0x00000000U) + +/*! + \brief deinitialize the EXTI + \param[in] none + \param[out] none + \retval none + */ +void exti_deinit(void) +{ + /* reset the value of all the EXTI registers */ + EXTI_INTEN = EXTI_REG_RESET_VALUE; + EXTI_EVEN = EXTI_REG_RESET_VALUE; + EXTI_RTEN = EXTI_REG_RESET_VALUE; + EXTI_FTEN = EXTI_REG_RESET_VALUE; + EXTI_SWIEV = EXTI_REG_RESET_VALUE; +} + +/*! + \brief initialize the EXTI + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[in] mode: interrupt or event mode, refer to exti_mode_enum + only one parameter can be selected which is shown as below: + \arg EXTI_INTERRUPT: interrupt mode + \arg EXTI_EVENT: event mode + \param[in] trig_type: trigger type, refer to exti_trig_type_enum + only one parameter can be selected which is shown as below: + \arg EXTI_TRIG_RISING: rising edge trigger + \arg EXTI_TRIG_FALLING: falling edge trigger + \arg EXTI_TRIG_BOTH: rising edge and falling edge trigger + \arg EXTI_TRIG_NONE: without rising edge or falling edge trigger + \param[out] none + \retval none + */ +void exti_init(exti_line_enum linex, exti_mode_enum mode, exti_trig_type_enum trig_type) +{ + /* reset the EXTI line x */ + EXTI_INTEN &= ~(uint32_t) linex; + EXTI_EVEN &= ~(uint32_t) linex; + EXTI_RTEN &= ~(uint32_t) linex; + EXTI_FTEN &= ~(uint32_t) linex; + + /* set the EXTI mode and enable the interrupts or events from EXTI line x */ + switch (mode) { + case EXTI_INTERRUPT: + EXTI_INTEN |= (uint32_t) linex; + break; + case EXTI_EVENT: + EXTI_EVEN |= (uint32_t) linex; + break; + default: + break; + } + + /* set the EXTI trigger type */ + switch (trig_type) { + case EXTI_TRIG_RISING: + EXTI_RTEN |= (uint32_t) linex; + EXTI_FTEN &= ~(uint32_t) linex; + break; + case EXTI_TRIG_FALLING: + EXTI_RTEN &= ~(uint32_t) linex; + EXTI_FTEN |= (uint32_t) linex; + break; + case EXTI_TRIG_BOTH: + EXTI_RTEN |= (uint32_t) linex; + EXTI_FTEN |= (uint32_t) linex; + break; + case EXTI_TRIG_NONE: + default: + break; + } +} + +/*! + \brief enable the interrupts from EXTI line x + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_interrupt_enable(exti_line_enum linex) +{ + EXTI_INTEN |= (uint32_t) linex; +} + +/*! + \brief enable the events from EXTI line x + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_event_enable(exti_line_enum linex) +{ + EXTI_EVEN |= (uint32_t) linex; +} + +/*! + \brief disable the interrupt from EXTI line x + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_interrupt_disable(exti_line_enum linex) +{ + EXTI_INTEN &= ~(uint32_t) linex; +} + +/*! + \brief disable the events from EXTI line x + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_event_disable(exti_line_enum linex) +{ + EXTI_EVEN &= ~(uint32_t) linex; +} + +/*! + \brief get EXTI lines flag + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval FlagStatus: status of flag (RESET or SET) +*/ +FlagStatus exti_flag_get(exti_line_enum linex) +{ + if (RESET != (EXTI_PD & (uint32_t) linex)) { + return SET; + } else { + return RESET; + } +} + +/*! + \brief clear EXTI lines pending flag + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_flag_clear(exti_line_enum linex) +{ + EXTI_PD = (uint32_t) linex; +} + +/*! + \brief get EXTI lines flag when the interrupt flag is set + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval FlagStatus: status of flag (RESET or SET) +*/ +FlagStatus exti_interrupt_flag_get(exti_line_enum linex) +{ + uint32_t flag_left, flag_right; + + flag_left = EXTI_PD & (uint32_t) linex; + flag_right = EXTI_INTEN & (uint32_t) linex; + + if ((RESET != flag_left) && (RESET != flag_right)) { + return SET; + } else { + return RESET; + } +} + +/*! + \brief clear EXTI lines pending flag + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_interrupt_flag_clear(exti_line_enum linex) +{ + EXTI_PD = (uint32_t) linex; +} + +/*! + \brief enable EXTI software interrupt event + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_software_interrupt_enable(exti_line_enum linex) +{ + EXTI_SWIEV |= (uint32_t) linex; +} + +/*! + \brief disable EXTI software interrupt event + \param[in] linex: EXTI line number, refer to exti_line_enum + only one parameter can be selected which is shown as below: + \arg EXTI_x (x=0..18): EXTI line x + \param[out] none + \retval none +*/ +void exti_software_interrupt_disable(exti_line_enum linex) +{ + EXTI_SWIEV &= ~(uint32_t) linex; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fmc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fmc.c new file mode 100644 index 00000000..c219a796 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fmc.c @@ -0,0 +1,649 @@ +/*! + \file gd32vf103_fmc.c + \brief FMC driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_fmc.h" + +/*! + \brief set the wait state counter value + \param[in] wscntwait state counter value + \arg WS_WSCNT_0: FMC 0 wait state + \arg WS_WSCNT_1: FMC 1 wait state + \arg WS_WSCNT_2: FMC 2 wait state + \param[out] none + \retval none + */ +void fmc_wscnt_set(uint32_t wscnt) +{ + uint32_t reg; + + reg = FMC_WS; + /* set the wait state counter value */ + reg &= ~FMC_WS_WSCNT; + FMC_WS = (reg | wscnt); +} + +/*! + \brief unlock the main FMC operation + \param[in] none + \param[out] none + \retval none + */ +void fmc_unlock(void) +{ + if((RESET != (FMC_CTL0 & FMC_CTL0_LK))){ + /* write the FMC unlock key */ + FMC_KEY0 = UNLOCK_KEY0; + FMC_KEY0 = UNLOCK_KEY1; + } +} + +/*! + \brief lock the main FMC operation + \param[in] none + \param[out] none + \retval none + */ +void fmc_lock(void) +{ + /* set the LK bit */ + FMC_CTL0 |= FMC_CTL0_LK; +} + + +/*! + \brief FMC erase page + \param[in] page_address: the page address to be erased. + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum fmc_page_erase(uint32_t page_address) +{ + fmc_state_enum fmc_state; + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + /* if the last operation is completed, start page erase */ + if (FMC_READY == fmc_state) { + FMC_CTL0 |= FMC_CTL0_PER; + FMC_ADDR0 = page_address; + FMC_CTL0 |= FMC_CTL0_START; + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + /* reset the PER bit */ + FMC_CTL0 &= ~FMC_CTL0_PER; + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief FMC erase whole chip + \param[in] none + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum fmc_mass_erase(void) +{ + fmc_state_enum fmc_state; + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* start whole chip erase */ + FMC_CTL0 |= FMC_CTL0_MER; + FMC_CTL0 |= FMC_CTL0_START; + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + /* reset the MER bit */ + FMC_CTL0 &= ~FMC_CTL0_MER; + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief FMC program a word at the corresponding address + \param[in] address: address to program + \param[in] data: word to program + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum fmc_word_program(uint32_t address, uint32_t data) +{ + fmc_state_enum fmc_state = FMC_READY; + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* set the PG bit to start program */ + FMC_CTL0 |= FMC_CTL0_PG; + REG32(address) = data; + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + /* reset the PG bit */ + FMC_CTL0 &= ~FMC_CTL0_PG; + } + /* return the FMC state */ + return fmc_state; +} +/* + \brief FMC program a half word at the corresponding address + \param[in] address: address to program + \param[in] data: halfword to program + \param[out] none + \retval state of FMC, refer to fmc_state_enum +*/ +fmc_state_enum fmc_halfword_program(uint32_t address, uint16_t data) +{ + fmc_state_enum fmc_state = FMC_READY; + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* set the PG bit to start program */ + FMC_CTL0 |= FMC_CTL0_PG; + REG16(address) = data; + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + /* reset the PG bit */ + FMC_CTL0 &= ~FMC_CTL0_PG; + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief unlock the option byte operation + \param[in] none + \param[out] none + \retval none + */ +void ob_unlock(void) +{ + if(RESET == (FMC_CTL0 & FMC_CTL0_OBWEN)){ + /* write the FMC key */ + FMC_OBKEY = UNLOCK_KEY0; + FMC_OBKEY = UNLOCK_KEY1; + } + + /* wait until OBWEN bit is set by hardware */ + while (RESET == (FMC_CTL0 & FMC_CTL0_OBWEN)) { + } +} + +/*! + \brief lock the option byte operation + \param[in] none + \param[out] none + \retval none + */ +void ob_lock(void) +{ + /* reset the OBWEN bit */ + FMC_CTL0 &= ~FMC_CTL0_OBWEN; +} + +/*! + \brief erase the FMC option byte + unlock the FMC_CTL0 and option byte before calling this function + \param[in] none + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum ob_erase(void) +{ + uint16_t temp_spc = FMC_NSPC; + + fmc_state_enum fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + /* check the option byte security protection value */ + if(RESET != ob_spc_get()){ + temp_spc = FMC_USPC; + } + + if(FMC_READY == fmc_state){ + + /* start erase the option byte */ + FMC_CTL0 |= FMC_CTL0_OBER; + FMC_CTL0 |= FMC_CTL0_START; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* reset the OBER bit */ + FMC_CTL0 &= ~FMC_CTL0_OBER; + /* set the OBPG bit */ + FMC_CTL0 |= FMC_CTL0_OBPG; + /* no security protection */ + OB_SPC = (uint16_t) temp_spc; + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + if (FMC_TOERR != fmc_state) { + /* reset the OBPG bit */ + FMC_CTL0 &= ~FMC_CTL0_OBPG; + } + }else{ + if(FMC_TOERR != fmc_state){ + /* reset the OBPG bit */ + FMC_CTL0 &= ~FMC_CTL0_OBPG; + } + } + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief enable write protection + \param[in] ob_wp: specify sector to be write protected, set the bit to 1 if + you want to protect the corresponding pages. meanwhile, sector + macro could used to set specific sector write protected. + one or more parameters can be selected which are shown as below: + \arg OB_WPx(x = 0..31): write protect specify sector + \arg OB_WP_ALL: write protect all sector + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum ob_write_protection_enable(uint32_t ob_wp) +{ + uint16_t temp_wp0, temp_wp1, temp_wp2, temp_wp3; + + fmc_state_enum fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + ob_wp = (uint32_t) (~ob_wp); + temp_wp0 = (uint16_t) (ob_wp & OB_WP0_WP0); + temp_wp1 = (uint16_t) ((ob_wp & OB_WP1_WP1) >> 8U); + temp_wp2 = (uint16_t) ((ob_wp & OB_WP2_WP2) >> 16U); + temp_wp3 = (uint16_t) ((ob_wp & OB_WP3_WP3) >> 24U); + + if(FMC_READY == fmc_state){ + + /* set the OBPG bit*/ + FMC_CTL0 |= FMC_CTL0_OBPG; + + if(0xFFU != temp_wp0){ + OB_WP0 = temp_wp0; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + } + if((FMC_READY == fmc_state) && (0xFFU != temp_wp1)){ + OB_WP1 = temp_wp1; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + } + if((FMC_READY == fmc_state) && (0xFFU != temp_wp2)){ + OB_WP2 = temp_wp2; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + } + if((FMC_READY == fmc_state) && (0xFFU != temp_wp3)){ + OB_WP3 = temp_wp3; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + } + if(FMC_TOERR != fmc_state){ + /* reset the OBPG bit */ + FMC_CTL0 &= ~FMC_CTL0_OBPG; + } + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief configure security protection + \param[in] ob_spc: specify security protection + only one parameter can be selected which is shown as below: + \arg FMC_NSPC: no security protection + \arg FMC_USPC: under security protection + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum ob_security_protection_config(uint8_t ob_spc) +{ + fmc_state_enum fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + FMC_CTL0 |= FMC_CTL0_OBER; + FMC_CTL0 |= FMC_CTL0_START; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* reset the OBER bit */ + FMC_CTL0 &= ~FMC_CTL0_OBER; + + /* start the option byte program */ + FMC_CTL0 |= FMC_CTL0_OBPG; + + OB_SPC = (uint16_t) ob_spc; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if (FMC_TOERR != fmc_state) { + /* reset the OBPG bit */ + FMC_CTL0 &= ~FMC_CTL0_OBPG; + } + }else{ + if (FMC_TOERR != fmc_state) { + /* reset the OBER bit */ + FMC_CTL0 &= ~FMC_CTL0_OBER; + } + } + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief program the FMC user option byte + \param[in] ob_fwdgt: option byte watchdog value + \arg OB_FWDGT_SW: software free watchdog + \arg OB_FWDGT_HW: hardware free watchdog + \param[in] ob_deepsleep: option byte deepsleep reset value + \arg OB_DEEPSLEEP_NRST: no reset when entering deepsleep mode + \arg OB_DEEPSLEEP_RST: generate a reset instead of entering deepsleep mode + \param[in] ob_stdby:option byte standby reset value + \arg OB_STDBY_NRST: no reset when entering standby mode + \arg OB_STDBY_RST: generate a reset instead of entering standby mode + \param[in] ob_boot: specifies the option byte boot bank value + \arg OB_BOOT_B0: boot from bank0 + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum ob_user_write(uint8_t ob_fwdgt, uint8_t ob_deepsleep, uint8_t ob_stdby, uint8_t ob_boot) +{ + fmc_state_enum fmc_state = FMC_READY; + uint8_t temp; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* set the OBPG bit*/ + FMC_CTL0 |= FMC_CTL0_OBPG; + + temp = ((uint8_t)((uint8_t)((uint8_t)(ob_boot | ob_fwdgt) | ob_deepsleep) | ob_stdby) | OB_USER_MASK); + OB_USER = (uint16_t) temp; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_TOERR != fmc_state){ + /* reset the OBPG bit */ + FMC_CTL0 &= ~FMC_CTL0_OBPG; + } + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief program option bytes data + \param[in] address: the option bytes address to be programmed + \param[in] data: the byte to be programmed + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum ob_data_program(uint32_t address, uint8_t data) { + fmc_state_enum fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_READY == fmc_state){ + /* set the OBPG bit */ + FMC_CTL0 |= FMC_CTL0_OBPG; + REG16(address) = data; + + /* wait for the FMC ready */ + fmc_state = fmc_ready_wait(FMC_TIMEOUT_COUNT); + + if(FMC_TOERR != fmc_state){ + /* reset the OBPG bit */ + FMC_CTL0 &= ~FMC_CTL0_OBPG; + } + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief get the FMC user option byte + \param[in] none + \param[out] none + \retval the FMC user option byte values + */ +uint8_t ob_user_get(void) +{ + /* return the FMC user option byte value */ + return (uint8_t) (FMC_OBSTAT >> 2U); +} + +/*! + \brief get OB_DATA in register FMC_OBSTAT + \param[in] none + \param[out] none + \retval ob_data + */ +uint16_t ob_data_get(void) +{ + return (uint16_t) (FMC_OBSTAT >> 10U); +} + +/*! + \brief get the FMC option byte write protection + \param[in] none + \param[out] none + \retval the FMC write protection option byte value + */ +uint32_t ob_write_protection_get(void) +{ + /* return the FMC write protection option byte value */ + return FMC_WP; +} + +/*! + \brief get the FMC option byte security protection + \param[in] none + \param[out] none + \retval FlagStatus: SET or RESET + */ +FlagStatus ob_spc_get(void) +{ + FlagStatus spc_state = RESET; + + if(RESET != (FMC_OBSTAT & FMC_OBSTAT_SPC)){ + spc_state = SET; + }else{ + spc_state = RESET; + } + return spc_state; +} + +/*! + \brief enable FMC interrupt + \param[in] interrupt: the FMC interrupt source + only one parameter can be selected which is shown as below: + \arg FMC_INT_END: enable FMC end of program interrupt + \arg FMC_INT_ERR: enable FMC error interrupt + \param[out] none + \retval none + */ +void fmc_interrupt_enable(uint32_t interrupt) +{ + FMC_REG_VAL(interrupt) |= BIT(FMC_BIT_POS(interrupt)); +} + +/*! + \brief disable FMC interrupt + \param[in] interrupt: the FMC interrupt source + only one parameter can be selected which is shown as below: + \arg FMC_INT_END: enable FMC end of program interrupt + \arg FMC_INT_ERR: enable FMC error interrupt + \param[out] none + \retval none + */ +void fmc_interrupt_disable(uint32_t interrupt) +{ + FMC_REG_VAL(interrupt) &= ~BIT(FMC_BIT_POS(interrupt)); +} + +/*! + \brief check flag is set or not + \param[in] flag: check FMC flag + only one parameter can be selected which is shown as below: + \arg FMC_FLAG_BUSY: FMC busy flag bit + \arg FMC_FLAG_PGERR: FMC operation error flag bit + \arg FMC_FLAG_WPERR: FMC erase/program protection error flag bit + \arg FMC_FLAG_END: FMC end of operation flag bit + \arg FMC_FLAG_OBERR: FMC option bytes read error flag bit + \param[out] none + \retval FlagStatus: SET or RESET + */ +FlagStatus fmc_flag_get(uint32_t flag) +{ + if(RESET != (FMC_REG_VAL(flag) & BIT(FMC_BIT_POS(flag)))){ + return SET; + } else { + return RESET; + } +} + +/*! + \brief clear the FMC flag + \param[in] flag: clear FMC flag + only one parameter can be selected which is shown as below: + \arg FMC_FLAG_PGERR: FMC operation error flag bit + \arg FMC_FLAG_WPERR: FMC erase/program protection error flag bit + \arg FMC_FLAG_END: FMC end of operation flag bit + \param[out] none + \retval none + */ +void fmc_flag_clear(uint32_t flag) +{ + FMC_REG_VAL(flag) = (!FMC_REG_VAL(flag)) | BIT(FMC_BIT_POS(flag)); +} + +/*! + \brief get FMC interrupt flag state + \param[in] flag: FMC interrupt flags, refer to fmc_interrupt_flag_enum + only one parameter can be selected which is shown as below: + \arg FMC_INT_FLAG_PGERR: FMC operation error interrupt flag bit + \arg FMC_INT_FLAG_WPERR: FMC erase/program protection error interrupt flag bit + \arg FMC_INT_FLAG_END: FMC end of operation interrupt flag bit + \param[out] none + \retval FlagStatus: SET or RESET + */ +FlagStatus fmc_interrupt_flag_get(fmc_interrupt_flag_enum flag) +{ + FlagStatus ret1 = RESET; + FlagStatus ret2 = RESET; + + if(FMC_STAT0_REG_OFFSET == FMC_REG_OFFSET_GET(flag)){ + /* get the staus of interrupt flag */ + ret1 = (FlagStatus) (FMC_REG_VALS(flag) & BIT(FMC_BIT_POS0(flag))); + /* get the staus of interrupt enale bit */ + ret2 = (FlagStatus) (FMC_CTL0 & BIT(FMC_BIT_POS1(flag))); + } + + if(ret1 && ret2){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear FMC interrupt flag state + \param[in] flag: FMC interrupt flags, refer to can_interrupt_flag_enum + only one parameter can be selected which is shown as below: + \arg FMC_INT_FLAG_PGERR: FMC operation error interrupt flag bit + \arg FMC_INT_FLAG_WPERR: FMC erase/program protection error interrupt flag bit + \arg FMC_INT_FLAG_END: FMC end of operation interrupt flag bit + \param[out] none + \retval none + */ +void fmc_interrupt_flag_clear(fmc_interrupt_flag_enum flag) +{ + FMC_REG_VALS(flag) |= BIT(FMC_BIT_POS0(flag)); +} + +/*! + \brief get the FMC state + \param[in] none + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum fmc_state_get(void) +{ + fmc_state_enum fmc_state = FMC_READY; + + if((uint32_t) 0x00U != (FMC_STAT0 & FMC_STAT0_BUSY)){ + fmc_state = FMC_BUSY; + }else{ + if((uint32_t) 0x00U != (FMC_STAT0 & FMC_STAT0_WPERR)){ + fmc_state = FMC_WPERR; + }else{ + if((uint32_t) 0x00U != (FMC_STAT0 & (FMC_STAT0_PGERR))){ + fmc_state = FMC_PGERR; + } + } + } + /* return the FMC state */ + return fmc_state; +} + +/*! + \brief check whether FMC is ready or not + \param[in] timeout: count of loop + \param[out] none + \retval state of FMC, refer to fmc_state_enum + */ +fmc_state_enum fmc_ready_wait(uint32_t timeout) +{ + fmc_state_enum fmc_state = FMC_BUSY; + + /* wait for FMC ready */ + do{ + /* get FMC state */ + fmc_state = fmc_state_get(); + timeout--; + }while((FMC_BUSY == fmc_state) && (0x00U != timeout)); + + if(FMC_BUSY == fmc_state){ + fmc_state = FMC_TOERR; + } + /* return the FMC state */ + return fmc_state; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fwdgt.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fwdgt.c new file mode 100644 index 00000000..c0f2a38e --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_fwdgt.c @@ -0,0 +1,151 @@ +/*! + \file gd32vf103_fwdgt.c + \brief FWDGT driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_fwdgt.h" + +/* write value to FWDGT_CTL_CMD bit field */ +#define CTL_CMD(regval) (BITS(0,15) & ((uint32_t)(regval) << 0)) +/* write value to FWDGT_RLD_RLD bit field */ +#define RLD_RLD(regval) (BITS(0,11) & ((uint32_t)(regval) << 0)) + +/*! + \brief enable write access to FWDGT_PSC and FWDGT_RLD + \param[in] none + \param[out] none + \retval none +*/ +void fwdgt_write_enable(void) +{ + FWDGT_CTL = FWDGT_WRITEACCESS_ENABLE; +} + +/*! + \brief disable write access to FWDGT_PSC and FWDGT_RLD + \param[in] none + \param[out] none + \retval none +*/ +void fwdgt_write_disable(void) +{ + FWDGT_CTL = FWDGT_WRITEACCESS_DISABLE; +} + +/*! + \brief start the free watchdog timer counter + \param[in] none + \param[out] none + \retval none +*/ +void fwdgt_enable(void) +{ + FWDGT_CTL = FWDGT_KEY_ENABLE; +} + +/*! + \brief reload the counter of FWDGT + \param[in] none + \param[out] none + \retval none +*/ +void fwdgt_counter_reload(void) +{ + FWDGT_CTL = FWDGT_KEY_RELOAD; +} + +/*! + \brief configure counter reload value, and prescaler divider value + \param[in] reload_value: specify reload value(0x0000 - 0x0FFF) + \param[in] prescaler_div: FWDGT prescaler value + only one parameter can be selected which is shown as below: + \arg FWDGT_PSC_DIV4: FWDGT prescaler set to 4 + \arg FWDGT_PSC_DIV8: FWDGT prescaler set to 8 + \arg FWDGT_PSC_DIV16: FWDGT prescaler set to 16 + \arg FWDGT_PSC_DIV32: FWDGT prescaler set to 32 + \arg FWDGT_PSC_DIV64: FWDGT prescaler set to 64 + \arg FWDGT_PSC_DIV128: FWDGT prescaler set to 128 + \arg FWDGT_PSC_DIV256: FWDGT prescaler set to 256 + \param[out] none + \retval ErrStatus: ERROR or SUCCESS +*/ +ErrStatus fwdgt_config(uint16_t reload_value, uint8_t prescaler_div) +{ + uint32_t timeout = FWDGT_PSC_TIMEOUT; + uint32_t flag_status = RESET; + + /* enable write access to FWDGT_PSC,and FWDGT_RLD */ + FWDGT_CTL = FWDGT_WRITEACCESS_ENABLE; + /* wait until the PUD flag to be reset */ + do{ + flag_status = FWDGT_STAT & FWDGT_STAT_PUD; + }while((--timeout > 0U) && ((uint32_t)RESET != flag_status)); + + if((uint32_t)RESET != flag_status){ + return ERROR; + } + /* configure FWDGT */ + FWDGT_PSC = (uint32_t)prescaler_div; + + timeout = FWDGT_RLD_TIMEOUT; + /* wait until the RUD flag to be reset */ + do{ + flag_status = FWDGT_STAT & FWDGT_STAT_RUD; + }while((--timeout > 0U) && ((uint32_t)RESET != flag_status)); + + if((uint32_t)RESET != flag_status){ + return ERROR; + } + FWDGT_RLD = RLD_RLD(reload_value); + /* reload the counter */ + FWDGT_CTL = FWDGT_KEY_RELOAD; + + return SUCCESS; +} + +/*! + \brief get flag state of FWDGT + \param[in] flag: flag to get + only one parameter can be selected which is shown as below: + \arg FWDGT_FLAG_PUD: a write operation to FWDGT_PSC register is on going + \arg FWDGT_FLAG_RUD: a write operation to FWDGT_RLD register is on going + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus fwdgt_flag_get(uint16_t flag) +{ + if(FWDGT_STAT & flag){ + return SET; + } + + return RESET; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_gpio.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_gpio.c new file mode 100644 index 00000000..8c396968 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_gpio.c @@ -0,0 +1,502 @@ +/*! + \file gd32vf103_gpio.c + \brief GPIO driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_gpio.h" + +#define AFIO_EXTI_SOURCE_MASK ((uint8_t)0x03U) /*!< AFIO exti source selection mask*/ +#define AFIO_EXTI_SOURCE_FIELDS ((uint8_t)0x04U) /*!< select AFIO exti source registers */ +#define LSB_16BIT_MASK ((uint16_t)0xFFFFU) /*!< LSB 16-bit mask */ +#define PCF_POSITION_MASK ((uint32_t)0x000F0000U) /*!< AFIO_PCF register position mask */ +#define PCF_SWJCFG_MASK ((uint32_t)0xF0FFFFFFU) /*!< AFIO_PCF register SWJCFG mask */ +#define PCF_LOCATION1_MASK ((uint32_t)0x00200000U) /*!< AFIO_PCF register location1 mask */ +#define PCF_LOCATION2_MASK ((uint32_t)0x00100000U) /*!< AFIO_PCF register location2 mask */ +#define AFIO_PCF1_FIELDS ((uint32_t)0x80000000U) /*!< select AFIO_PCF1 register */ +#define GPIO_OUTPUT_PORT_OFFSET ((uint32_t)4U) /*!< GPIO event output port offset*/ + +/*! + \brief reset GPIO port + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[out] none + \retval none +*/ +void gpio_deinit(uint32_t gpio_periph) +{ + switch (gpio_periph) { + case GPIOA: + /* reset GPIOA */ + rcu_periph_reset_enable(RCU_GPIOARST); + rcu_periph_reset_disable(RCU_GPIOARST); + break; + case GPIOB: + /* reset GPIOB */ + rcu_periph_reset_enable(RCU_GPIOBRST); + rcu_periph_reset_disable(RCU_GPIOBRST); + break; + case GPIOC: + /* reset GPIOC */ + rcu_periph_reset_enable(RCU_GPIOCRST); + rcu_periph_reset_disable(RCU_GPIOCRST); + break; + case GPIOD: + /* reset GPIOD */ + rcu_periph_reset_enable(RCU_GPIODRST); + rcu_periph_reset_disable(RCU_GPIODRST); + break; + case GPIOE: + /* reset GPIOE */ + rcu_periph_reset_enable(RCU_GPIOERST); + rcu_periph_reset_disable(RCU_GPIOERST); + break; + default: + break; + } +} + +/*! + \brief reset alternate function I/O(AFIO) + \param[in] none + \param[out] none + \retval none +*/ +void gpio_afio_deinit(void) +{ + rcu_periph_reset_enable(RCU_AFRST); + rcu_periph_reset_disable(RCU_AFRST); +} + +/*! + \brief GPIO parameter initialization + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] mode: gpio pin mode + only one parameter can be selected which is shown as below: + \arg GPIO_MODE_AIN: analog input mode + \arg GPIO_MODE_IN_FLOATING: floating input mode + \arg GPIO_MODE_IPD: pull-down input mode + \arg GPIO_MODE_IPU: pull-up input mode + \arg GPIO_MODE_OUT_OD: GPIO output with open-drain + \arg GPIO_MODE_OUT_PP: GPIO output with push-pull + \arg GPIO_MODE_AF_OD: AFIO output with open-drain + \arg GPIO_MODE_AF_PP: AFIO output with push-pull + \param[in] speed: gpio output max speed value + only one parameter can be selected which is shown as below: + \arg GPIO_OSPEED_10MHZ: output max speed 10MHz + \arg GPIO_OSPEED_2MHZ: output max speed 2MHz + \arg GPIO_OSPEED_50MHZ: output max speed 50MHz + \param[in] pin: GPIO pin + one or more parameters can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + + \param[out] none + \retval none +*/ +void gpio_init(uint32_t gpio_periph, uint32_t mode, uint32_t speed, + uint32_t pin) +{ + uint16_t i; + uint32_t temp_mode = 0U; + uint32_t reg = 0U; + + /* GPIO mode configuration */ + temp_mode = (uint32_t) (mode & ((uint32_t) 0x0FU)); + + /* GPIO speed configuration */ + if (((uint32_t) 0x00U) != ((uint32_t) mode & ((uint32_t) 0x10U))) { + /* output mode max speed:10MHz,2MHz,50MHz */ + temp_mode |= (uint32_t) speed; + } + + /* configure the eight low port pins with GPIO_CTL0 */ + for (i = 0U; i < 8U; i++) { + if ((1U << i) & pin) { + reg = GPIO_CTL0(gpio_periph); + + /* clear the specified pin mode bits */ + reg &= ~GPIO_MODE_MASK(i); + /* set the specified pin mode bits */ + reg |= GPIO_MODE_SET(i, temp_mode); + + /* set IPD or IPU */ + if (GPIO_MODE_IPD == mode) { + /* reset the corresponding OCTL bit */ + GPIO_BC(gpio_periph) = (uint32_t) ((1U << i) & pin); + } else { + /* set the corresponding OCTL bit */ + if (GPIO_MODE_IPU == mode) { + GPIO_BOP(gpio_periph) = (uint32_t) ((1U << i) & pin); + } + } + /* set GPIO_CTL0 register */ + GPIO_CTL0(gpio_periph) = reg; + } + } + /* configure the eight high port pins with GPIO_CTL1 */ + for (i = 8U; i < 16U; i++) { + if ((1U << i) & pin) { + reg = GPIO_CTL1(gpio_periph); + + /* clear the specified pin mode bits */ + reg &= ~GPIO_MODE_MASK(i - 8U); + /* set the specified pin mode bits */ + reg |= GPIO_MODE_SET(i - 8U, temp_mode); + + /* set IPD or IPU */ + if (GPIO_MODE_IPD == mode) { + /* reset the corresponding OCTL bit */ + GPIO_BC(gpio_periph) = (uint32_t) ((1U << i) & pin); + } else { + /* set the corresponding OCTL bit */ + if (GPIO_MODE_IPU == mode) { + GPIO_BOP(gpio_periph) = (uint32_t) ((1U << i) & pin); + } + } + /* set GPIO_CTL1 register */ + GPIO_CTL1(gpio_periph) = reg; + } + } +} + +/*! + \brief set GPIO pin + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] pin: GPIO pin + one or more parameters can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + \param[out] none + \retval none +*/ +void gpio_bit_set(uint32_t gpio_periph, uint32_t pin) +{ + GPIO_BOP(gpio_periph) = (uint32_t) pin; +} + +/*! + \brief reset GPIO pin + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] pin: GPIO pin + one or more parameters can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + \param[out] none + \retval none +*/ +void gpio_bit_reset(uint32_t gpio_periph, uint32_t pin) +{ + GPIO_BC(gpio_periph) = (uint32_t) pin; +} + +/*! + \brief write data to the specified GPIO pin + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] pin: GPIO pin + one or more parameters can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + \param[in] bit_value: SET or RESET + only one parameter can be selected which is shown as below: + \arg RESET: clear the port pin + \arg SET: set the port pin + \param[out] none + \retval none +*/ +void gpio_bit_write(uint32_t gpio_periph, uint32_t pin, bit_status bit_value) +{ + if (RESET != bit_value) { + GPIO_BOP(gpio_periph) = (uint32_t) pin; + } else { + GPIO_BC(gpio_periph) = (uint32_t) pin; + } +} + +/*! + \brief write data to the specified GPIO port + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] data: specify the value to be written to the port output data register + \param[out] none + \retval none +*/ +void gpio_port_write(uint32_t gpio_periph, uint16_t data) +{ + GPIO_OCTL(gpio_periph) = (uint32_t) data; +} + +/*! + \brief get GPIO pin input status + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] pin: GPIO pin + only one parameter can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + \param[out] none + \retval input status of gpio pin: SET or RESET +*/ +FlagStatus gpio_input_bit_get(uint32_t gpio_periph, uint32_t pin) +{ + if ((uint32_t) RESET != (GPIO_ISTAT(gpio_periph) & (pin))) { + return SET; + } else { + return RESET; + } +} + +/*! + \brief get GPIO port input status + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[out] none + \retval input status of gpio all pins +*/ +uint16_t gpio_input_port_get(uint32_t gpio_periph) +{ + return (uint16_t) (GPIO_ISTAT(gpio_periph)); +} + +/*! + \brief get GPIO pin output status + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] pin: GPIO pin + only one parameter can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + \param[out] none + \retval output status of gpio pin: SET or RESET +*/ +FlagStatus gpio_output_bit_get(uint32_t gpio_periph, uint32_t pin) +{ + if ((uint32_t) RESET != (GPIO_OCTL(gpio_periph) & (pin))) { + return SET; + } else { + return RESET; + } +} + +/*! + \brief get GPIO port output status + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[out] none + \retval output status of gpio all pins +*/ +uint16_t gpio_output_port_get(uint32_t gpio_periph) +{ + return ((uint16_t) GPIO_OCTL(gpio_periph)); +} + +/*! + \brief configure GPIO pin remap + \param[in] gpio_remap: select the pin to remap + only one parameter can be selected which are shown as below: + \arg GPIO_SPI0_REMAP: SPI0 remapping + \arg GPIO_I2C0_REMAP: I2C0 remapping + \arg GPIO_USART0_REMAP: USART0 remapping + \arg GPIO_USART1_REMAP: USART1 remapping + \arg GPIO_USART2_PARTIAL_REMAP: USART2 partial remapping + \arg GPIO_USART2_FULL_REMAP: USART2 full remapping + \arg GPIO_TIMER0_PARTIAL_REMAP: TIMER0 partial remapping + \arg GPIO_TIMER0_FULL_REMAP: TIMER0 full remapping + \arg GPIO_TIMER1_PARTIAL_REMAP0: TIMER1 partial remapping + \arg GPIO_TIMER1_PARTIAL_REMAP1: TIMER1 partial remapping + \arg GPIO_TIMER1_FULL_REMAP: TIMER1 full remapping + \arg GPIO_TIMER2_PARTIAL_REMAP: TIMER2 partial remapping + \arg GPIO_TIMER2_FULL_REMAP: TIMER2 full remapping + \arg GPIO_TIMER3_REMAP: TIMER3 remapping + \arg GPIO_CAN0_PARTIAL_REMAP: CAN0 partial remapping + \arg GPIO_CAN0_FULL_REMAP: CAN0 full remapping + \arg GPIO_PD01_REMAP: PD01 remapping + \arg GPIO_TIMER4CH3_IREMAP: TIMER4 channel3 internal remapping + \arg GPIO_CAN1_REMAP: CAN1 remapping + \arg GPIO_SWJ_NONJTRST_REMAP: JTAG-DP,but without NJTRST + \arg GPIO_SWJ_DISABLE_REMAP: JTAG-DP disabled + \arg GPIO_SPI2_REMAP: SPI2 remapping + \arg GPIO_TIMER1ITI1_REMAP: TIMER1 internal trigger 1 remapping + \arg GPIO_EXMC_NADV_REMAP: EXMC_NADV connect/disconnect + \param[in] newvalue: ENABLE or DISABLE + \param[out] none + \retval none +*/ +void gpio_pin_remap_config(uint32_t remap, ControlStatus newvalue) +{ + uint32_t remap1 = 0U, remap2 = 0U, temp_reg = 0U, temp_mask = 0U; + + if (AFIO_PCF1_FIELDS == (remap & AFIO_PCF1_FIELDS)) { + /* get AFIO_PCF1 regiter value */ + temp_reg = AFIO_PCF1; + } else { + /* get AFIO_PCF0 regiter value */ + temp_reg = AFIO_PCF0; + } + + temp_mask = (remap & PCF_POSITION_MASK) >> 0x10U; + remap1 = remap & LSB_16BIT_MASK; + + /* judge pin remap type */ + if ((PCF_LOCATION1_MASK | PCF_LOCATION2_MASK) + == (remap & (PCF_LOCATION1_MASK | PCF_LOCATION2_MASK))) { + temp_reg &= PCF_SWJCFG_MASK; + AFIO_PCF0 &= PCF_SWJCFG_MASK; + } else if (PCF_LOCATION2_MASK == (remap & PCF_LOCATION2_MASK)) { + remap2 = ((uint32_t) 0x03U) << temp_mask; + temp_reg &= ~remap2; + temp_reg |= ~PCF_SWJCFG_MASK; + } else { + temp_reg &= ~(remap1 << ((remap >> 0x15U) * 0x10U)); + temp_reg |= ~PCF_SWJCFG_MASK; + } + + /* set pin remap value */ + if (DISABLE != newvalue) { + temp_reg |= (remap1 << ((remap >> 0x15U) * 0x10U)); + } + + if (AFIO_PCF1_FIELDS == (remap & AFIO_PCF1_FIELDS)) { + /* set AFIO_PCF1 regiter value */ + AFIO_PCF1 = temp_reg; + } else { + /* set AFIO_PCF0 regiter value */ + AFIO_PCF0 = temp_reg; + } +} + +/*! + \brief select GPIO pin exti sources + \param[in] gpio_outputport: gpio event output port + only one parameter can be selected which are shown as below: + \arg GPIO_PORT_SOURCE_GPIOA: output port source A + \arg GPIO_PORT_SOURCE_GPIOB: output port source B + \arg GPIO_PORT_SOURCE_GPIOC: output port source C + \arg GPIO_PORT_SOURCE_GPIOD: output port source D + \arg GPIO_PORT_SOURCE_GPIOE: output port source E + \param[in] gpio_outputpin: GPIO_PIN_SOURCE_x(x=0..15) + \param[out] none + \retval none +*/ +void gpio_exti_source_select(uint8_t output_port, uint8_t output_pin) +{ + uint32_t source = 0U; + source = ((uint32_t) 0x0FU) + << (AFIO_EXTI_SOURCE_FIELDS * (output_pin & AFIO_EXTI_SOURCE_MASK)); + + /* select EXTI sources */ + if (GPIO_PIN_SOURCE_4 > output_pin) { + /* select EXTI0/EXTI1/EXTI2/EXTI3 */ + AFIO_EXTISS0 &= ~source; + AFIO_EXTISS0 |= (((uint32_t) output_port) + << (AFIO_EXTI_SOURCE_FIELDS + * (output_pin & AFIO_EXTI_SOURCE_MASK))); + } else if (GPIO_PIN_SOURCE_8 > output_pin) { + /* select EXTI4/EXTI5/EXTI6/EXTI7 */ + AFIO_EXTISS1 &= ~source; + AFIO_EXTISS1 |= (((uint32_t) output_port) + << (AFIO_EXTI_SOURCE_FIELDS + * (output_pin & AFIO_EXTI_SOURCE_MASK))); + } else if (GPIO_PIN_SOURCE_12 > output_pin) { + /* select EXTI8/EXTI9/EXTI10/EXTI11 */ + AFIO_EXTISS2 &= ~source; + AFIO_EXTISS2 |= (((uint32_t) output_port) + << (AFIO_EXTI_SOURCE_FIELDS + * (output_pin & AFIO_EXTI_SOURCE_MASK))); + } else { + /* select EXTI12/EXTI13/EXTI14/EXTI15 */ + AFIO_EXTISS3 &= ~source; + AFIO_EXTISS3 |= (((uint32_t) output_port) + << (AFIO_EXTI_SOURCE_FIELDS + * (output_pin & AFIO_EXTI_SOURCE_MASK))); + } +} + +/*! + \brief configure GPIO pin event output + \param[in] output_port: gpio event output port + only one parameter can be selected which are shown as below: + \arg GPIO_EVENT_PORT_GPIOA: event output port A + \arg GPIO_EVENT_PORT_GPIOB: event output port B + \arg GPIO_EVENT_PORT_GPIOC: event output port C + \arg GPIO_EVENT_PORT_GPIOD: event output port D + \arg GPIO_EVENT_PORT_GPIOE: event output port E + \param[in] output_pin: + only one parameter can be selected which are shown as below: + \arg GPIO_EVENT_PIN_x(x=0..15) + \param[out] none + \retval none +*/ +void gpio_event_output_config(uint8_t output_port, uint8_t output_pin) +{ + uint32_t reg = 0U; + reg = AFIO_EC; + + /* clear AFIO_EC_PORT and AFIO_EC_PIN bits */ + reg &= (uint32_t) (~(AFIO_EC_PORT | AFIO_EC_PIN)); + + reg |= (uint32_t) ((uint32_t) output_port << GPIO_OUTPUT_PORT_OFFSET); + reg |= (uint32_t) output_pin; + + AFIO_EC = reg; +} + +/*! + \brief enable GPIO pin event output + \param[in] none + \param[out] none + \retval none +*/ +void gpio_event_output_enable(void) +{ + AFIO_EC |= AFIO_EC_EOE; +} + +/*! + \brief disable GPIO pin event output + \param[in] none + \param[out] none + \retval none +*/ +void gpio_event_output_disable(void) +{ + AFIO_EC &= (uint32_t) (~AFIO_EC_EOE); +} + +/*! + \brief lock GPIO pin + \param[in] gpio_periph: GPIOx(x = A,B,C,D,E) + \param[in] pin: GPIO pin + one or more parameters can be selected which are shown as below: + \arg GPIO_PIN_x(x=0..15), GPIO_PIN_ALL + \param[out] none + \retval none +*/ +void gpio_pin_lock(uint32_t gpio_periph, uint32_t pin) +{ + uint32_t lock = 0x00010000U; + lock |= pin; + + /* lock key writing sequence: write 1 -> write 0 -> write 1 -> read 0 -> read 1 */ + GPIO_LOCK(gpio_periph) = (uint32_t) lock; + GPIO_LOCK(gpio_periph) = (uint32_t) pin; + GPIO_LOCK(gpio_periph) = (uint32_t) lock; + lock = GPIO_LOCK(gpio_periph); + lock = GPIO_LOCK(gpio_periph); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_i2c.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_i2c.c new file mode 100644 index 00000000..1e6ab305 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_i2c.c @@ -0,0 +1,726 @@ +/*! + \file gd32vf103_i2c.c + \brief I2C driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_i2c.h" + +/* I2C register bit mask */ +#define I2CCLK_MAX ((uint32_t)0x00000048U) /*!< i2cclk maximum value */ +#define I2CCLK_MIN ((uint32_t)0x00000002U) /*!< i2cclk minimum value */ +#define I2C_FLAG_MASK ((uint32_t)0x0000FFFFU) /*!< i2c flag mask */ +#define I2C_ADDRESS_MASK ((uint32_t)0x000003FFU) /*!< i2c address mask */ +#define I2C_ADDRESS2_MASK ((uint32_t)0x000000FEU) /*!< the second i2c address mask */ + +/* I2C register bit offset */ +#define STAT1_PECV_OFFSET ((uint32_t)8U) /* bit offset of PECV in I2C_STAT1 */ + +/*! + \brief reset I2C + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval none + */ +void i2c_deinit(uint32_t i2c_periph) +{ + switch (i2c_periph) { + case I2C0: + /* reset I2C0 */ + rcu_periph_reset_enable(RCU_I2C0RST); + rcu_periph_reset_disable(RCU_I2C0RST); + break; + case I2C1: + /* reset I2C1 */ + rcu_periph_reset_enable(RCU_I2C1RST); + rcu_periph_reset_disable(RCU_I2C1RST); + break; + default: + break; + } +} + +/*! + \brief configure I2C clock + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] clkspeed: I2C clock speed, supports standard mode (up to 100 kHz), fast mode (up to 400 kHz) + \param[in] dutycyc: duty cycle in fast mode + only one parameter can be selected which is shown as below: + \arg I2C_DTCY_2: T_low/T_high=2 + \arg I2C_DTCY_16_9: T_low/T_high=16/9 + \param[out] none + \retval none + */ +void i2c_clock_config(uint32_t i2c_periph, uint32_t clkspeed, uint32_t dutycyc) +{ + uint32_t pclk1, clkc, freq, risetime; + uint32_t temp; + + pclk1 = rcu_clock_freq_get(CK_APB1); + /* I2C peripheral clock frequency */ + freq = (uint32_t) (pclk1 / 1000000U); + if (freq >= I2CCLK_MAX) { + freq = I2CCLK_MAX; + } + temp = I2C_CTL1(i2c_periph); + temp &= ~I2C_CTL1_I2CCLK; + temp |= freq; + + I2C_CTL1(i2c_periph) = temp; + + if (100000U >= clkspeed) { + /* the maximum SCL rise time is 1000ns in standard mode */ + risetime = (uint32_t) ((pclk1 / 1000000U) + 1U); + if (risetime >= I2CCLK_MAX) { + I2C_RT(i2c_periph) = I2CCLK_MAX; + } else if (risetime <= I2CCLK_MIN) { + I2C_RT(i2c_periph) = I2CCLK_MIN; + } else { + I2C_RT(i2c_periph) = risetime; + } + clkc = (uint32_t) (pclk1 / (clkspeed * 2U)); + if (clkc < 0x04U) { + /* the CLKC in standard mode minmum value is 4 */ + clkc = 0x04U; + } + I2C_CKCFG(i2c_periph) |= (I2C_CKCFG_CLKC & clkc); + + } else if (400000U >= clkspeed) { + /* the maximum SCL rise time is 300ns in fast mode */ + I2C_RT(i2c_periph) = (uint32_t) (((freq * (uint32_t) 300U) + / (uint32_t) 1000U) + (uint32_t) 1U); + if (I2C_DTCY_2 == dutycyc) { + /* I2C duty cycle is 2 */ + clkc = (uint32_t) (pclk1 / (clkspeed * 3U)); + I2C_CKCFG(i2c_periph) &= ~I2C_CKCFG_DTCY; + } else { + /* I2C duty cycle is 16/9 */ + clkc = (uint32_t) (pclk1 / (clkspeed * 25U)); + I2C_CKCFG(i2c_periph) |= I2C_CKCFG_DTCY; + } + if (0U == (clkc & I2C_CKCFG_CLKC)) { + /* the CLKC in fast mode minmum value is 1 */ + clkc |= 0x0001U; + } + I2C_CKCFG(i2c_periph) |= I2C_CKCFG_FAST; + I2C_CKCFG(i2c_periph) |= clkc; + } else { + } +} + +/*! + \brief configure I2C address + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] mode: + only one parameter can be selected which is shown as below: + \arg I2C_I2CMODE_ENABLE: I2C mode + \arg I2C_SMBUSMODE_ENABLE: SMBus mode + \param[in] addformat: 7bits or 10bits + only one parameter can be selected which is shown as below: + \arg I2C_ADDFORMAT_7BITS: 7bits + \arg I2C_ADDFORMAT_10BITS: 10bits + \param[in] addr: I2C address + \param[out] none + \retval none + */ +void i2c_mode_addr_config(uint32_t i2c_periph, uint32_t mode,uint32_t addformat, uint32_t addr) +{ + /* SMBus/I2C mode selected */ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_SMBEN); + ctl |= mode; + I2C_CTL0(i2c_periph) = ctl; + /* configure address */ + addr = addr & I2C_ADDRESS_MASK; + I2C_SADDR0(i2c_periph) = (addformat | addr); +} + +/*! + \brief SMBus type selection + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] type: + only one parameter can be selected which is shown as below: + \arg I2C_SMBUS_DEVICE: device + \arg I2C_SMBUS_HOST: host + \param[out] none + \retval none + */ +void i2c_smbus_type_config(uint32_t i2c_periph, uint32_t type) +{ + if (I2C_SMBUS_HOST == type) { + I2C_CTL0(i2c_periph) |= I2C_CTL0_SMBSEL; + } else { + I2C_CTL0(i2c_periph) &= ~(I2C_CTL0_SMBSEL); + } +} + +/*! + \brief whether or not to send an ACK + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] ack: + only one parameter can be selected which is shown as below: + \arg I2C_ACK_ENABLE: ACK will be sent + \arg I2C_ACK_DISABLE: ACK will not be sent + \param[out] none + \retval none + */ +void i2c_ack_config(uint32_t i2c_periph, uint32_t ack) +{ + if (I2C_ACK_ENABLE == ack) { + I2C_CTL0(i2c_periph) |= I2C_CTL0_ACKEN; + } else { + I2C_CTL0(i2c_periph) &= ~(I2C_CTL0_ACKEN); + } +} + +/*! + \brief configure I2C POAP position + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] pos: + only one parameter can be selected which is shown as below: + \arg I2C_ACKPOS_CURRENT: whether to send ACK or not for the current + \arg I2C_ACKPOS_NEXT: whether to send ACK or not for the next byte + \param[out] none + \retval none + */ +void i2c_ackpos_config(uint32_t i2c_periph, uint32_t pos) +{ + /* configure I2C POAP position */ + if (I2C_ACKPOS_NEXT == pos) { + I2C_CTL0(i2c_periph) |= I2C_CTL0_POAP; + } else { + I2C_CTL0(i2c_periph) &= ~(I2C_CTL0_POAP); + } +} + +/*! + \brief master sends slave address + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] addr: slave address + \param[in] trandirection: transmitter or receiver + only one parameter can be selected which is shown as below: + \arg I2C_TRANSMITTER: transmitter + \arg I2C_RECEIVER: receiver + \param[out] none + \retval none + */ +void i2c_master_addressing(uint32_t i2c_periph, uint32_t addr,uint32_t trandirection) +{ + /* master is a transmitter or a receiver */ + if (I2C_TRANSMITTER == trandirection) { + addr = addr & I2C_TRANSMITTER; + } else { + addr = addr | I2C_RECEIVER; + } + /* send slave address */ + I2C_DATA(i2c_periph) = addr; +} + +/*! + \brief configure I2C saddress1 + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] addr: I2C address + \param[out] none + \retval none +*/ +void i2c_saddr1_config(uint32_t i2c_periph,uint32_t addr) +{ + /* configure saddress1 */ + I2C_SADDR1(i2c_periph) = (0xFE & addr); +} + +/*! + \brief enable dual-address mode + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] addr: the second address in dual-address mode + \param[out] none + \retval none +*/ +void i2c_dualaddr_enable(uint32_t i2c_periph, uint32_t addr) +{ + /* configure address */ + addr = addr & I2C_ADDRESS2_MASK; + I2C_SADDR1(i2c_periph) = (I2C_SADDR1_DUADEN | addr); +} + +/*! + \brief disable dual-address mode + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval none +*/ +void i2c_dualaddr_disable(uint32_t i2c_periph) +{ + I2C_SADDR1(i2c_periph) &= ~(I2C_SADDR1_DUADEN); +} + +/*! + \brief enable I2C + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval none + */ +void i2c_enable(uint32_t i2c_periph) +{ + I2C_CTL0(i2c_periph) |= I2C_CTL0_I2CEN; +} + +/*! + \brief disable I2C + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval none + */ +void i2c_disable(uint32_t i2c_periph) +{ + I2C_CTL0(i2c_periph) &= ~(I2C_CTL0_I2CEN); +} + +/*! + \brief generate a START condition on I2C bus + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval none + */ +void i2c_start_on_bus(uint32_t i2c_periph) +{ + I2C_CTL0(i2c_periph) |= I2C_CTL0_START; +} + +/*! + \brief generate a STOP condition on I2C bus + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval none + */ +void i2c_stop_on_bus(uint32_t i2c_periph) +{ + I2C_CTL0(i2c_periph) |= I2C_CTL0_STOP; +} + +/*! + \brief I2C transmit data function + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] data: data of transmission + \param[out] none + \retval none + */ +void i2c_data_transmit(uint32_t i2c_periph, uint8_t data) +{ + I2C_DATA(i2c_periph) = DATA_TRANS(data); +} + +/*! + \brief I2C receive data function + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval data of received + */ +uint8_t i2c_data_receive(uint32_t i2c_periph) +{ + return (uint8_t) DATA_RECV(I2C_DATA(i2c_periph)); +} + +/*! + \brief enable I2C DMA mode + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] dmastate: + only one parameter can be selected which is shown as below: + \arg I2C_DMA_ON: DMA mode enable + \arg I2C_DMA_OFF: DMA mode disable + \param[out] none + \retval none + */ +void i2c_dma_enable(uint32_t i2c_periph, uint32_t dmastate) +{ + /* configure I2C DMA function */ + uint32_t ctl = 0U; + + ctl = I2C_CTL1(i2c_periph); + ctl &= ~(I2C_CTL1_DMAON); + ctl |= dmastate; + I2C_CTL1(i2c_periph) = ctl; +} + +/*! + \brief configure whether next DMA EOT is DMA last transfer or not + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] dmalast: + only one parameter can be selected which is shown as below: + \arg I2C_DMALST_ON: next DMA EOT is the last transfer + \arg I2C_DMALST_OFF: next DMA EOT is not the last transfer + \param[out] none + \retval none + */ +void i2c_dma_last_transfer_config(uint32_t i2c_periph, uint32_t dmalast) +{ + /* configure DMA last transfer */ + uint32_t ctl = 0U; + + ctl = I2C_CTL1(i2c_periph); + ctl &= ~(I2C_CTL1_DMALST); + ctl |= dmalast; + I2C_CTL1(i2c_periph) = ctl; +} + +/*! + \brief whether to stretch SCL low when data is not ready in slave mode + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] stretchpara: + only one parameter can be selected which is shown as below: + \arg I2C_SCLSTRETCH_ENABLE: SCL stretching is enabled + \arg I2C_SCLSTRETCH_DISABLE: SCL stretching is disabled + \param[out] none + \retval none + */ +void i2c_stretch_scl_low_config(uint32_t i2c_periph, uint32_t stretchpara) +{ + /* configure I2C SCL strerching enable or disable */ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_SS); + ctl |= stretchpara; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief whether or not to response to a general call + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] gcallpara: + only one parameter can be selected which is shown as below: + \arg I2C_GCEN_ENABLE: slave will response to a general call + \arg I2C_GCEN_DISABLE: slave will not response to a general call + \param[out] none + \retval none + */ +void i2c_slave_response_to_gcall_config(uint32_t i2c_periph, uint32_t gcallpara) +{ + /* configure slave response to a general call enable or disable */ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_GCEN); + ctl |= gcallpara; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief software reset I2C + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] sreset: + only one parameter can be selected which is shown as below: + \arg I2C_SRESET_SET: I2C is under reset + \arg I2C_SRESET_RESET: I2C is not under reset + \param[out] none + \retval none + */ +void i2c_software_reset_config(uint32_t i2c_periph, uint32_t sreset) +{ + /* modify CTL0 and configure software reset I2C state */ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_SRESET); + ctl |= sreset; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief I2C PEC calculation on or off + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] pecpara: + only one parameter can be selected which is shown as below: + \arg I2C_PEC_ENABLE: PEC calculation on + \arg I2C_PEC_DISABLE: PEC calculation off + \param[out] none + \retval none + */ +void i2c_pec_enable(uint32_t i2c_periph, uint32_t pecstate) +{ + /* on/off PEC calculation */ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_PECEN); + ctl |= pecstate; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief I2C whether to transfer PEC value + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] pecpara: + only one parameter can be selected which is shown as below: + \arg I2C_PECTRANS_ENABLE: transfer PEC + \arg I2C_PECTRANS_DISABLE: not transfer PEC + \param[out] none + \retval none + */ +void i2c_pec_transfer_enable(uint32_t i2c_periph, uint32_t pecpara) +{ + /* whether to transfer PEC */ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_PECTRANS); + ctl |= pecpara; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief get packet error checking value + \param[in] i2c_periph: I2Cx(x=0,1) + \param[out] none + \retval PEC value + */ +uint8_t i2c_pec_value_get(uint32_t i2c_periph) +{ + return (uint8_t) ((I2C_STAT1(i2c_periph) & I2C_STAT1_PECV)>> STAT1_PECV_OFFSET); +} + +/*! + \brief I2C issue alert through SMBA pin + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] smbuspara: + only one parameter can be selected which is shown as below: + \arg I2C_SALTSEND_ENABLE: issue alert through SMBA pin + \arg I2C_SALTSEND_DISABLE: not issue alert through SMBA pin + \param[out] none + \retval none + */ +void i2c_smbus_issue_alert(uint32_t i2c_periph, uint32_t smbuspara) +{ + /* issue alert through SMBA pin configure*/ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_SALT); + ctl |= smbuspara; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief enable or disable I2C ARP protocol in SMBus switch + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] arpstate: + only one parameter can be selected which is shown as below: + \arg I2C_ARP_ENABLE: enable ARP + \arg I2C_ARP_DISABLE: disable ARP + \param[out] none + \retval none + */ +void i2c_smbus_arp_enable(uint32_t i2c_periph, uint32_t arpstate) +{ + /* enable or disable I2C ARP protocol*/ + uint32_t ctl = 0U; + + ctl = I2C_CTL0(i2c_periph); + ctl &= ~(I2C_CTL0_ARPEN); + ctl |= arpstate; + I2C_CTL0(i2c_periph) = ctl; +} + +/*! + \brief check I2C flag is set or not + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] flag: I2C flags, refer to i2c_flag_enum + only one parameter can be selected which is shown as below: + \arg I2C_FLAG_SBSEND: start condition send out + \arg I2C_FLAG_ADDSEND: address is sent in master mode or received and matches in slave mode + \arg I2C_FLAG_BTC: byte transmission finishes + \arg I2C_FLAG_ADD10SEND: header of 10-bit address is sent in master mode + \arg I2C_FLAG_STPDET: stop condition detected in slave mode + \arg I2C_FLAG_RBNE: I2C_DATA is not Empty during receiving + \arg I2C_FLAG_TBE: I2C_DATA is empty during transmitting + \arg I2C_FLAG_BERR: a bus error occurs indication a unexpected start or stop condition on I2C bus + \arg I2C_FLAG_LOSTARB: arbitration lost in master mode + \arg I2C_FLAG_AERR: acknowledge error + \arg I2C_FLAG_OUERR: overrun or underrun situation occurs in slave mode + \arg I2C_FLAG_PECERR: PEC error when receiving data + \arg I2C_FLAG_SMBTO: timeout signal in SMBus mode + \arg I2C_FLAG_SMBALT: SMBus alert status + \arg I2C_FLAG_MASTER: a flag indicating whether I2C block is in master or slave mode + \arg I2C_FLAG_I2CBSY: busy flag + \arg I2C_FLAG_TR: whether the I2C is a transmitter or a receiver + \arg I2C_FLAG_RXGC: general call address (00h) received + \arg I2C_FLAG_DEFSMB: default address of SMBus device + \arg I2C_FLAG_HSTSMB: SMBus host header detected in slave mode + \arg I2C_FLAG_DUMODF: dual flag in slave mode indicating which address is matched in dual-address mode + \param[out] none + \retval FlagStatus: SET or RESET + */ +FlagStatus i2c_flag_get(uint32_t i2c_periph, i2c_flag_enum flag) +{ + if (RESET != (I2C_REG_VAL(i2c_periph, flag) & BIT(I2C_BIT_POS(flag)))) { + return SET; + } else { + return RESET; + } +} + +/*! + \brief clear I2C flag + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] flag: I2C flags, refer to i2c_flag_enum + only one parameter can be selected which is shown as below: + \arg I2C_FLAG_SMBALT: SMBus Alert status + \arg I2C_FLAG_SMBTO: timeout signal in SMBus mode + \arg I2C_FLAG_PECERR: PEC error when receiving data + \arg I2C_FLAG_OUERR: over-run or under-run situation occurs in slave mode + \arg I2C_FLAG_AERR: acknowledge error + \arg I2C_FLAG_LOSTARB: arbitration lost in master mode + \arg I2C_FLAG_BERR: a bus error + \arg I2C_FLAG_ADDSEND: cleared by reading I2C_STAT0 and reading I2C_STAT1 + \param[out] none + \retval none + */ +void i2c_flag_clear(uint32_t i2c_periph, i2c_flag_enum flag) +{ + uint32_t temp; + if (I2C_FLAG_ADDSEND == flag) { + /* read I2C_STAT0 and then read I2C_STAT1 to clear ADDSEND */ + temp = I2C_STAT0(i2c_periph); + temp = I2C_STAT1(i2c_periph); + } else { + I2C_REG_VAL(i2c_periph, flag) &= ~BIT(I2C_BIT_POS(flag)); + } +} + +/*! + \brief enable I2C interrupt + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] interrupt: I2C interrupts, refer to i2c_interrupt_enum + only one parameter can be selected which is shown as below: + \arg I2C_INT_ERR: error interrupt enable + \arg I2C_INT_EV: event interrupt enable + \arg I2C_INT_BUF: buffer interrupt enable + \param[out] none + \retval none + */ +void i2c_interrupt_enable(uint32_t i2c_periph, i2c_interrupt_enum interrupt) +{ + I2C_REG_VAL(i2c_periph, interrupt) |= BIT(I2C_BIT_POS(interrupt)); +} + +/*! + \brief disable I2C interrupt + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] interrupt: I2C interrupts, refer to i2c_flag_enum + only one parameter can be selected which is shown as below: + \arg I2C_INT_ERR: error interrupt enable + \arg I2C_INT_EV: event interrupt enable + \arg I2C_INT_BUF: buffer interrupt enable + \param[out] none + \retval none + */ +void i2c_interrupt_disable(uint32_t i2c_periph, i2c_interrupt_enum interrupt) +{ + I2C_REG_VAL(i2c_periph, interrupt) &= ~BIT(I2C_BIT_POS(interrupt)); +} + +/*! + \brief check I2C interrupt flag + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] int_flag: I2C interrupt flags, refer to i2c_interrupt_flag_enum + only one parameter can be selected which is shown as below: + \arg I2C_INT_FLAG_SBSEND: start condition sent out in master mode interrupt flag + \arg I2C_INT_FLAG_ADDSEND: address is sent in master mode or received and matches in slave mode interrupt flag + \arg I2C_INT_FLAG_BTC: byte transmission finishes + \arg I2C_INT_FLAG_ADD10SEND: header of 10-bit address is sent in master mode interrupt flag + \arg I2C_INT_FLAG_STPDET: etop condition detected in slave mode interrupt flag + \arg I2C_INT_FLAG_RBNE: I2C_DATA is not Empty during receiving interrupt flag + \arg I2C_INT_FLAG_TBE: I2C_DATA is empty during transmitting interrupt flag + \arg I2C_INT_FLAG_BERR: a bus error occurs indication a unexpected start or stop condition on I2C bus interrupt flag + \arg I2C_INT_FLAG_LOSTARB: arbitration lost in master mode interrupt flag + \arg I2C_INT_FLAG_AERR: acknowledge error interrupt flag + \arg I2C_INT_FLAG_OUERR: over-run or under-run situation occurs in slave mode interrupt flag + \arg I2C_INT_FLAG_PECERR: PEC error when receiving data interrupt flag + \arg I2C_INT_FLAG_SMBTO: timeout signal in SMBus mode interrupt flag + \arg I2C_INT_FLAG_SMBALT: SMBus Alert status interrupt flag + \param[out] none + \retval FlagStatus: SET or RESET + */ +FlagStatus i2c_interrupt_flag_get(uint32_t i2c_periph,i2c_interrupt_flag_enum int_flag) +{ + uint32_t intenable = 0U, flagstatus = 0U, bufie; + + /* check BUFIE */ + bufie = I2C_CTL1(i2c_periph) & I2C_CTL1_BUFIE; + + /* get the interrupt enable bit status */ + intenable = (I2C_REG_VAL(i2c_periph, int_flag) & BIT(I2C_BIT_POS(int_flag))); + /* get the corresponding flag bit status */ + flagstatus = (I2C_REG_VAL2(i2c_periph, int_flag)& BIT(I2C_BIT_POS2(int_flag))); + + if ((I2C_INT_FLAG_RBNE == int_flag) || (I2C_INT_FLAG_TBE == int_flag)) { + if (intenable && bufie) { + intenable = 1U; + } else { + intenable = 0U; + } + } + if ((0U != flagstatus) && (0U != intenable)) { + return SET; + } else { + return RESET; + } +} + +/*! + \brief clear I2C interrupt flag + \param[in] i2c_periph: I2Cx(x=0,1) + \param[in] int_flag: I2C interrupt flags, refer to i2c_interrupt_flag_enum + only one parameter can be selected which is shown as below: + \arg I2C_INT_FLAG_ADDSEND: address is sent in master mode or received and matches in slave mode interrupt flag + \arg I2C_INT_FLAG_BERR: a bus error occurs indication a unexpected start or stop condition on I2C bus interrupt flag + \arg I2C_INT_FLAG_LOSTARB: arbitration lost in master mode interrupt flag + \arg I2C_INT_FLAG_AERR: acknowledge error interrupt flag + \arg I2C_INT_FLAG_OUERR: over-run or under-run situation occurs in slave mode interrupt flag + \arg I2C_INT_FLAG_PECERR: PEC error when receiving data interrupt flag + \arg I2C_INT_FLAG_SMBTO: timeout signal in SMBus mode interrupt flag + \arg I2C_INT_FLAG_SMBALT: SMBus Alert status interrupt flag + \param[out] none + \retval none + */ +void i2c_interrupt_flag_clear(uint32_t i2c_periph,i2c_interrupt_flag_enum int_flag) +{ + uint32_t temp; + if (I2C_INT_FLAG_ADDSEND == int_flag) { + /* read I2C_STAT0 and then read I2C_STAT1 to clear ADDSEND */ + temp = I2C_STAT0(i2c_periph); + temp = I2C_STAT1(i2c_periph); + } else { + I2C_REG_VAL2(i2c_periph, int_flag) &= ~BIT(I2C_BIT_POS2(int_flag)); + } +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_pmu.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_pmu.c new file mode 100644 index 00000000..cbbd4411 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_pmu.c @@ -0,0 +1,263 @@ +/*! + \file gd32vf103_pmu.c + \brief PMU driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_pmu.h" + +/*! + \brief reset PMU register + \param[in] none + \param[out] none + \retval none +*/ +void pmu_deinit(void) +{ + /* reset PMU */ + rcu_periph_reset_enable(RCU_PMURST); + rcu_periph_reset_disable(RCU_PMURST); +} + +/*! + \brief select low voltage detector threshold + \param[in] lvdt_n: + only one parameter can be selected which is shown as below: + \arg PMU_LVDT_0: voltage threshold is 2.2V + \arg PMU_LVDT_1: voltage threshold is 2.3V + \arg PMU_LVDT_2: voltage threshold is 2.4V + \arg PMU_LVDT_3: voltage threshold is 2.5V + \arg PMU_LVDT_4: voltage threshold is 2.6V + \arg PMU_LVDT_5: voltage threshold is 2.7V + \arg PMU_LVDT_6: voltage threshold is 2.8V + \arg PMU_LVDT_7: voltage threshold is 2.9V + \param[out] none + \retval none +*/ +void pmu_lvd_select(uint32_t lvdt_n) +{ + /* disable LVD */ + PMU_CTL &= ~PMU_CTL_LVDEN; + /* clear LVDT bits */ + PMU_CTL &= ~PMU_CTL_LVDT; + /* set LVDT bits according to lvdt_n */ + PMU_CTL |= lvdt_n; + /* enable LVD */ + PMU_CTL |= PMU_CTL_LVDEN; +} + +/*! + \brief disable PMU lvd + \param[in] none + \param[out] none + \retval none +*/ +void pmu_lvd_disable(void) +{ + /* disable LVD */ + PMU_CTL &= ~PMU_CTL_LVDEN; +} + +/*! + \brief PMU work at sleep mode + \param[in] sleepmodecmd: + only one parameter can be selected which is shown as below: + \arg WFI_CMD: use WFI command + \arg WFE_CMD: use WFE command + \param[out] none + \retval none +*/ +void pmu_to_sleepmode(uint8_t sleepmodecmd) +{ + /* clear sleepdeep bit of RISC-V system control register */ + __RV_CSR_CLEAR(CSR_WFE, WFE_WFE); + + /* select WFI or WFE command to enter sleep mode */ + if(WFI_CMD == sleepmodecmd){ + __WFI(); + }else{ + __disable_irq(); + __WFE(); + __enable_irq(); + } +} + +/*! + \brief PMU work at deepsleep mode + \param[in] ldo: + only one parameter can be selected which is shown as below: + \arg PMU_LDO_NORMAL: LDO work at normal power mode when pmu enter deepsleep mode + \arg PMU_LDO_LOWPOWER: LDO work at low power mode when pmu enter deepsleep mode + \param[in] deepsleepmodecmd: + only one parameter can be selected which is shown as below: + \arg WFI_CMD: use WFI command + \arg WFE_CMD: use WFE command + \param[out] none + \retval none +*/ +void pmu_to_deepsleepmode(uint32_t ldo,uint8_t deepsleepmodecmd) +{ + /* clear stbmod and ldolp bits */ + PMU_CTL &= ~((uint32_t)(PMU_CTL_STBMOD | PMU_CTL_LDOLP)); + /* set ldolp bit according to pmu_ldo */ + PMU_CTL |= ldo; + /* set CSR_SLEEPVALUE bit of RISC-V system control register */ + __RV_CSR_SET(CSR_WFE, WFE_WFE); + /* select WFI or WFE command to enter deepsleep mode */ + if(WFI_CMD == deepsleepmodecmd){ + __WFI(); + }else{ + __disable_irq(); + __WFE(); + __enable_irq(); + } + /* reset sleepdeep bit of RISC-V system control register */ + __RV_CSR_CLEAR(CSR_WFE, WFE_WFE); +} + +/*! + \brief pmu work at standby mode + \param[in] standbymodecmd: + only one parameter can be selected which is shown as below: + \arg WFI_CMD: use WFI command + \arg WFE_CMD: use WFE command + \param[out] none + \retval none +*/ +void pmu_to_standbymode(uint8_t standbymodecmd) +{ + /* set CSR_SLEEPVALUE bit of RISC-V system control register */ + __RV_CSR_SET(CSR_WFE, WFE_WFE); + + /* set stbmod bit */ + PMU_CTL |= PMU_CTL_STBMOD; + + /* reset wakeup flag */ + PMU_CTL |= PMU_CTL_WURST; + + /* select WFI or WFE command to enter standby mode */ + if(WFI_CMD == standbymodecmd){ + __WFI(); + }else{ + __disable_irq(); + __WFE(); + __enable_irq(); + } + __RV_CSR_CLEAR(CSR_WFE, WFE_WFE); +} + +/*! + \brief enable wakeup pin + \param[in] none + \param[out] none + \retval none +*/ +void pmu_wakeup_pin_enable(void) +{ + PMU_CS |= PMU_CS_WUPEN; +} + +/*! + \brief disable wakeup pin + \param[in] none + \param[out] none + \retval none +*/ +void pmu_wakeup_pin_disable(void) +{ + PMU_CS &= ~PMU_CS_WUPEN; +} + +/*! + \brief enable write access to the registers in backup domain + \param[in] none + \param[out] none + \retval none +*/ +void pmu_backup_write_enable(void) +{ + PMU_CTL |= PMU_CTL_BKPWEN; +} + +/*! + \brief disable write access to the registers in backup domain + \param[in] none + \param[out] none + \retval none +*/ +void pmu_backup_write_disable(void) +{ + PMU_CTL &= ~PMU_CTL_BKPWEN; +} + +/*! + \brief get flag state + \param[in] flag: + only one parameter can be selected which is shown as below: + \arg PMU_FLAG_WAKEUP: wakeup flag + \arg PMU_FLAG_STANDBY: standby flag + \arg PMU_FLAG_LVD: lvd flag + \param[out] none + \retval FlagStatus SET or RESET +*/ +FlagStatus pmu_flag_get(uint32_t flag) +{ + if(PMU_CS & flag){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear flag bit + \param[in] flag_reset: + only one parameter can be selected which is shown as below: + \arg PMU_FLAG_RESET_WAKEUP: reset wakeup flag + \arg PMU_FLAG_RESET_STANDBY: reset standby flag + \param[out] none + \retval none +*/ +void pmu_flag_clear(uint32_t flag_reset) +{ + switch(flag_reset){ + case PMU_FLAG_RESET_WAKEUP: + /* reset wakeup flag */ + PMU_CTL |= PMU_CTL_WURST; + break; + case PMU_FLAG_RESET_STANDBY: + /* reset standby flag */ + PMU_CTL |= PMU_CTL_STBRST; + break; + default : + break; + } +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rcu.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rcu.c new file mode 100644 index 00000000..73cf832c --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rcu.c @@ -0,0 +1,1103 @@ +/*! + \file gd32vf103_rcu.c + \brief RCU driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_rcu.h" + + +/*! + \brief deinitialize the RCU + \param[in] none + \param[out] none + \retval none +*/ +void rcu_deinit(void) +{ + /* enable IRC8M */ + RCU_CTL |= RCU_CTL_IRC8MEN; + rcu_osci_stab_wait(RCU_IRC8M); + + /* reset CFG0 register */ + RCU_CFG0 &= ~(RCU_CFG0_SCS | RCU_CFG0_AHBPSC | RCU_CFG0_APB1PSC | RCU_CFG0_APB2PSC | + RCU_CFG0_ADCPSC | RCU_CFG0_PLLSEL | RCU_CFG0_PREDV0_LSB | RCU_CFG0_PLLMF | + RCU_CFG0_USBFSPSC | RCU_CFG0_CKOUT0SEL | RCU_CFG0_ADCPSC_2 | RCU_CFG0_PLLMF_4); + /* reset CTL register */ + RCU_CTL &= ~(RCU_CTL_HXTALEN | RCU_CTL_CKMEN | RCU_CTL_PLLEN); + RCU_CTL &= ~RCU_CTL_HXTALBPS; + RCU_CTL &= ~(RCU_CTL_PLL1EN | RCU_CTL_PLL2EN); + /* reset INT and CFG1 register */ + RCU_INT = 0x00ff0000U; + RCU_CFG1 &= ~(RCU_CFG1_PREDV0 | RCU_CFG1_PREDV1 | RCU_CFG1_PLL1MF | RCU_CFG1_PLL2MF | + RCU_CFG1_PREDV0SEL | RCU_CFG1_I2S1SEL | RCU_CFG1_I2S2SEL); +} + +/*! + \brief enable the peripherals clock + \param[in] periph: RCU peripherals, refer to rcu_periph_enum + only one parameter can be selected which is shown as below: + \arg RCU_GPIOx (x=A,B,C,D,E): GPIO ports clock + \arg RCU_AF : alternate function clock + \arg RCU_CRC: CRC clock + \arg RCU_DMAx (x=0,1): DMA clock + \arg RCU_USBFS: USBFS clock + \arg RCU_EXMC: EXMC clock + \arg RCU_TIMERx (x=0,1,2,3,4,5,6): TIMER clock + \arg RCU_WWDGT: WWDGT clock + \arg RCU_SPIx (x=0,1,2): SPI clock + \arg RCU_USARTx (x=0,1,2): USART clock + \arg RCU_UARTx (x=3,4): UART clock + \arg RCU_I2Cx (x=0,1): I2C clock + \arg RCU_CANx (x=0,1): CAN clock + \arg RCU_PMU: PMU clock + \arg RCU_DAC: DAC clock + \arg RCU_RTC: RTC clock + \arg RCU_ADCx (x=0,1): ADC clock + \arg RCU_BKPI: BKP interface clock + \param[out] none + \retval none +*/ +void rcu_periph_clock_enable(rcu_periph_enum periph) +{ + RCU_REG_VAL(periph) |= BIT(RCU_BIT_POS(periph)); +} + +/*! + \brief disable the peripherals clock + \param[in] periph: RCU peripherals, refer to rcu_periph_enum + only one parameter can be selected which is shown as below: + \arg RCU_GPIOx (x=A,B,C,D,E): GPIO ports clock + \arg RCU_AF: alternate function clock + \arg RCU_CRC: CRC clock + \arg RCU_DMAx (x=0,1): DMA clock + \arg RCU_USBFS: USBFS clock + \arg RCU_EXMC: EXMC clock + \arg RCU_TIMERx (x=0,1,2,3,4,5,6): TIMER clock + \arg RCU_WWDGT: WWDGT clock + \arg RCU_SPIx (x=0,1,2): SPI clock + \arg RCU_USARTx (x=0,1,2): USART clock + \arg RCU_UARTx (x=3,4): UART clock + \arg RCU_I2Cx (x=0,1): I2C clock + \arg RCU_CANx (x=0,1): CAN clock + \arg RCU_PMU: PMU clock + \arg RCU_DAC: DAC clock + \arg RCU_RTC: RTC clock + \arg RCU_ADCx (x=0,1): ADC clock + \arg RCU_BKPI: BKP interface clock + \param[out] none + \retval none +*/ +void rcu_periph_clock_disable(rcu_periph_enum periph) +{ + RCU_REG_VAL(periph) &= ~BIT(RCU_BIT_POS(periph)); +} + +/*! + \brief enable the peripherals clock when sleep mode + \param[in] periph: RCU peripherals, refer to rcu_periph_sleep_enum + only one parameter can be selected which is shown as below: + \arg RCU_FMC_SLP: FMC clock + \arg RCU_SRAM_SLP: SRAM clock + \param[out] none + \retval none +*/ +void rcu_periph_clock_sleep_enable(rcu_periph_sleep_enum periph) +{ + RCU_REG_VAL(periph) |= BIT(RCU_BIT_POS(periph)); +} + +/*! + \brief disable the peripherals clock when sleep mode + \param[in] periph: RCU peripherals, refer to rcu_periph_sleep_enum + only one parameter can be selected which is shown as below: + \arg RCU_FMC_SLP: FMC clock + \arg RCU_SRAM_SLP: SRAM clock + \param[out] none + \retval none +*/ +void rcu_periph_clock_sleep_disable(rcu_periph_sleep_enum periph) +{ + RCU_REG_VAL(periph) &= ~BIT(RCU_BIT_POS(periph)); +} + +/*! + \brief reset the peripherals + \param[in] periph_reset: RCU peripherals reset, refer to rcu_periph_reset_enum + only one parameter can be selected which is shown as below: + \arg RCU_GPIOxRST (x=A,B,C,D,E): reset GPIO ports + \arg RCU_AFRST : reset alternate function clock + \arg RCU_USBFSRST: reset USBFS + \arg RCU_TIMERxRST (x=0,1,2,3,4,5,6): reset TIMER + \arg RCU_WWDGTRST: reset WWDGT + \arg RCU_SPIxRST (x=0,1,2): reset SPI + \arg RCU_USARTxRST (x=0,1,2): reset USART + \arg RCU_UARTxRST (x=3,4): reset UART + \arg RCU_I2CxRST (x=0,1): reset I2C + \arg RCU_CANxRST (x=0,1): reset CAN + \arg RCU_PMURST: reset PMU + \arg RCU_DACRST: reset DAC + \arg RCU_ADCxRST (x=0,1): reset ADC + \arg RCU_BKPIRST: reset BKPI + \param[out] none + \retval none +*/ +void rcu_periph_reset_enable(rcu_periph_reset_enum periph_reset) +{ + RCU_REG_VAL(periph_reset) |= BIT(RCU_BIT_POS(periph_reset)); +} + +/*! + \brief disable reset the peripheral + \param[in] periph_reset: RCU peripherals reset, refer to rcu_periph_reset_enum + only one parameter can be selected which is shown as below: + \arg RCU_GPIOxRST (x=A,B,C,D,E): reset GPIO ports + \arg RCU_AFRST : reset alternate function clock + \arg RCU_USBFSRST: reset USBFS + \arg RCU_TIMERxRST (x=0,1,2,3,4,5,6): reset TIMER + \arg RCU_WWDGTRST: reset WWDGT + \arg RCU_SPIxRST (x=0,1,2): reset SPI + \arg RCU_USARTxRST (x=0,1,2): reset USART + \arg RCU_UARTxRST (x=3,4): reset UART + \arg RCU_I2CxRST (x=0,1): reset I2C + \arg RCU_CANxRST (x=0,1): reset CAN + \arg RCU_PMURST: reset PMU + \arg RCU_DACRST: reset DAC + \arg RCU_ADCxRST (x=0,1): reset ADC + \arg RCU_BKPIRST: reset BKPI + \param[out] none + \retval none +*/ +void rcu_periph_reset_disable(rcu_periph_reset_enum periph_reset) +{ + RCU_REG_VAL(periph_reset) &= ~BIT(RCU_BIT_POS(periph_reset)); +} + +/*! + \brief reset the BKP domain + \param[in] none + \param[out] none + \retval none +*/ +void rcu_bkp_reset_enable(void) +{ + RCU_BDCTL |= RCU_BDCTL_BKPRST; +} + +/*! + \brief disable the BKP domain reset + \param[in] none + \param[out] none + \retval none +*/ +void rcu_bkp_reset_disable(void) +{ + RCU_BDCTL &= ~RCU_BDCTL_BKPRST; +} + +/*! + \brief configure the system clock source + \param[in] ck_sys: system clock source select + only one parameter can be selected which is shown as below: + \arg RCU_CKSYSSRC_IRC8M: select CK_IRC8M as the CK_SYS source + \arg RCU_CKSYSSRC_HXTAL: select CK_HXTAL as the CK_SYS source + \arg RCU_CKSYSSRC_PLL: select CK_PLL as the CK_SYS source + \param[out] none + \retval none +*/ +void rcu_system_clock_source_config(uint32_t ck_sys) +{ + uint32_t reg; + + reg = RCU_CFG0; + /* reset the SCS bits and set according to ck_sys */ + reg &= ~RCU_CFG0_SCS; + RCU_CFG0 = (reg | ck_sys); +} + +/*! + \brief get the system clock source + \param[in] none + \param[out] none + \retval which clock is selected as CK_SYS source + \arg RCU_SCSS_IRC8M: CK_IRC8M is selected as the CK_SYS source + \arg RCU_SCSS_HXTAL: CK_HXTAL is selected as the CK_SYS source + \arg RCU_SCSS_PLL: CK_PLL is selected as the CK_SYS source +*/ +uint32_t rcu_system_clock_source_get(void) +{ + return (RCU_CFG0 & RCU_CFG0_SCSS); +} + +/*! + \brief configure the AHB clock prescaler selection + \param[in] ck_ahb: AHB clock prescaler selection + only one parameter can be selected which is shown as below: + \arg RCU_AHB_CKSYS_DIVx, x=1, 2, 4, 8, 16, 64, 128, 256, 512 + \param[out] none + \retval none +*/ +void rcu_ahb_clock_config(uint32_t ck_ahb) +{ + uint32_t reg; + + reg = RCU_CFG0; + + /* reset the AHBPSC bits and set according to ck_ahb */ + reg &= ~RCU_CFG0_AHBPSC; + RCU_CFG0 = (reg | ck_ahb); +} + +/*! + \brief configure the APB1 clock prescaler selection + \param[in] ck_apb1: APB1 clock prescaler selection + only one parameter can be selected which is shown as below: + \arg RCU_APB1_CKAHB_DIV1: select CK_AHB as CK_APB1 + \arg RCU_APB1_CKAHB_DIV2: select CK_AHB/2 as CK_APB1 + \arg RCU_APB1_CKAHB_DIV4: select CK_AHB/4 as CK_APB1 + \arg RCU_APB1_CKAHB_DIV8: select CK_AHB/8 as CK_APB1 + \arg RCU_APB1_CKAHB_DIV16: select CK_AHB/16 as CK_APB1 + \param[out] none + \retval none +*/ +void rcu_apb1_clock_config(uint32_t ck_apb1) +{ + uint32_t reg; + + reg = RCU_CFG0; + + /* reset the APB1PSC and set according to ck_apb1 */ + reg &= ~RCU_CFG0_APB1PSC; + RCU_CFG0 = (reg | ck_apb1); +} + +/*! + \brief configure the APB2 clock prescaler selection + \param[in] ck_apb2: APB2 clock prescaler selection + only one parameter can be selected which is shown as below: + \arg RCU_APB2_CKAHB_DIV1: select CK_AHB as CK_APB2 + \arg RCU_APB2_CKAHB_DIV2: select CK_AHB/2 as CK_APB2 + \arg RCU_APB2_CKAHB_DIV4: select CK_AHB/4 as CK_APB2 + \arg RCU_APB2_CKAHB_DIV8: select CK_AHB/8 as CK_APB2 + \arg RCU_APB2_CKAHB_DIV16: select CK_AHB/16 as CK_APB2 + \param[out] none + \retval none +*/ +void rcu_apb2_clock_config(uint32_t ck_apb2) +{ + uint32_t reg; + + reg = RCU_CFG0; + + /* reset the APB2PSC and set according to ck_apb2 */ + reg &= ~RCU_CFG0_APB2PSC; + RCU_CFG0 = (reg | ck_apb2); +} + +/*! + \brief configure the CK_OUT0 clock source + \param[in] ckout0_src: CK_OUT0 clock source selection + only one parameter can be selected which is shown as below: + \arg RCU_CKOUT0SRC_NONE: no clock selected + \arg RCU_CKOUT0SRC_CKSYS: system clock selected + \arg RCU_CKOUT0SRC_IRC8M: high speed 8M internal oscillator clock selected + \arg RCU_CKOUT0SRC_HXTAL: HXTAL selected + \arg RCU_CKOUT0SRC_CKPLL_DIV2: CK_PLL/2 selected + \arg RCU_CKOUT0SRC_CKPLL1: CK_PLL1 selected + \arg RCU_CKOUT0SRC_CKPLL2_DIV2: CK_PLL2/2 selected + \arg RCU_CKOUT0SRC_EXT1: EXT1 selected + \arg RCU_CKOUT0SRC_CKPLL2: PLL2 selected + \param[out] none + \retval none +*/ +void rcu_ckout0_config(uint32_t ckout0_src) +{ + uint32_t reg; + + reg = RCU_CFG0; + + /* reset the CKOUT0SRC, set according to ckout0_src */ + reg &= ~RCU_CFG0_CKOUT0SEL; + RCU_CFG0 = (reg | ckout0_src); +} + +/*! + \brief configure the main PLL clock + \param[in] pll_src: PLL clock source selection + only one parameter can be selected which is shown as below: + \arg RCU_PLLSRC_IRC8M_DIV2: IRC8M/2 clock selected as source clock of PLL + \arg RCU_PLLSRC_HXTAL: HXTAL selected as source clock of PLL + \param[in] pll_mul: PLL clock multiplication factor + only one parameter can be selected which is shown as below: + \arg RCU_PLL_MULx (x = 2..14, 6.5, 16..32) + \param[out] none + \retval none +*/ +void rcu_pll_config(uint32_t pll_src, uint32_t pll_mul) +{ + uint32_t reg = 0U; + + reg = RCU_CFG0; + + /* PLL clock source and multiplication factor configuration */ + reg &= ~(RCU_CFG0_PLLSEL | RCU_CFG0_PLLMF | RCU_CFG0_PLLMF_4); + reg |= (pll_src | pll_mul); + + RCU_CFG0 = reg; +} + +/*! + \brief configure the PREDV0 division factor and clock source + \param[in] predv0_source: PREDV0 input clock source selection + only one parameter can be selected which is shown as below: + \arg RCU_PREDV0SRC_HXTAL: HXTAL selected as PREDV0 input source clock + \arg RCU_PREDV0SRC_CKPLL1: CK_PLL1 selected as PREDV0 input source clock + \param[in] predv0_div: PREDV0 division factor + only one parameter can be selected which is shown as below: + \arg RCU_PREDV0_DIVx, x = 1..16 + \param[out] none + \retval none +*/ +void rcu_predv0_config(uint32_t predv0_source, uint32_t predv0_div) +{ + uint32_t reg = 0U; + + reg = RCU_CFG1; + /* reset PREDV0SEL and PREDV0 bits */ + reg &= ~(RCU_CFG1_PREDV0SEL | RCU_CFG1_PREDV0); + /* set the PREDV0SEL and PREDV0 division factor */ + reg |= (predv0_source | predv0_div); + + RCU_CFG1 = reg; +} + +/*! + \brief configure the PREDV1 division factor + \param[in] predv1_div: PREDV1 division factor + only one parameter can be selected which is shown as below: + \arg RCU_PREDV1_DIVx, x = 1..16 + \param[out] none + \retval none +*/ +void rcu_predv1_config(uint32_t predv1_div) +{ + uint32_t reg = 0U; + + reg = RCU_CFG1; + /* reset the PREDV1 bits */ + reg &= ~RCU_CFG1_PREDV1; + /* set the PREDV1 division factor */ + reg |= predv1_div; + + RCU_CFG1 = reg; +} + +/*! + \brief configure the PLL1 clock + \param[in] pll_mul: PLL clock multiplication factor + only one parameter can be selected which is shown as below: + \arg RCU_PLL1_MULx (x = 8..16, 20) + \param[out] none + \retval none +*/ +void rcu_pll1_config(uint32_t pll_mul) +{ + RCU_CFG1 &= ~RCU_CFG1_PLL1MF; + RCU_CFG1 |= pll_mul; +} + +/*! + \brief configure the PLL2 clock + \param[in] pll_mul: PLL clock multiplication factor + only one parameter can be selected which is shown as below: + \arg RCU_PLL2_MULx (x = 8..16, 20) + \param[out] none + \retval none +*/ +void rcu_pll2_config(uint32_t pll_mul) +{ + RCU_CFG1 &= ~RCU_CFG1_PLL2MF; + RCU_CFG1 |= pll_mul; +} + +/*! + \brief configure the ADC prescaler factor + \param[in] adc_psc: ADC prescaler factor + only one parameter can be selected which is shown as below: + \arg RCU_CKADC_CKAPB2_DIV2: ADC prescaler select CK_APB2/2 + \arg RCU_CKADC_CKAPB2_DIV4: ADC prescaler select CK_APB2/4 + \arg RCU_CKADC_CKAPB2_DIV6: ADC prescaler select CK_APB2/6 + \arg RCU_CKADC_CKAPB2_DIV8: ADC prescaler select CK_APB2/8 + \arg RCU_CKADC_CKAPB2_DIV12: ADC prescaler select CK_APB2/12 + \arg RCU_CKADC_CKAPB2_DIV16: ADC prescaler select CK_APB2/16 + \param[out] none + \retval none +*/ +void rcu_adc_clock_config(uint32_t adc_psc) +{ + uint32_t reg0; + + /* reset the ADCPSC bits */ + reg0 = RCU_CFG0; + reg0 &= ~(RCU_CFG0_ADCPSC_2 | RCU_CFG0_ADCPSC); + + /* set the ADC prescaler factor */ + switch(adc_psc){ + case RCU_CKADC_CKAPB2_DIV2: + case RCU_CKADC_CKAPB2_DIV4: + case RCU_CKADC_CKAPB2_DIV6: + case RCU_CKADC_CKAPB2_DIV8: + reg0 |= (adc_psc << 14); + break; + + case RCU_CKADC_CKAPB2_DIV12: + case RCU_CKADC_CKAPB2_DIV16: + adc_psc &= ~BIT(2); + reg0 |= (adc_psc << 14 | RCU_CFG0_ADCPSC_2); + break; + + default: + break; + } + + /* set the register */ + RCU_CFG0 = reg0; +} + +/*! + \brief configure the USBFS prescaler factor + \param[in] usb_psc: USB prescaler factor + only one parameter can be selected which is shown as below: + \arg RCU_CKUSB_CKPLL_DIV1_5: USBFS prescaler select CK_PLL/1.5 + \arg RCU_CKUSB_CKPLL_DIV1: USBFS prescaler select CK_PLL/1 + \arg RCU_CKUSB_CKPLL_DIV2_5: USBFS prescaler select CK_PLL/2.5 + \arg RCU_CKUSB_CKPLL_DIV2: USBFS prescaler select CK_PLL/2 + \param[out] none + \retval none +*/ +void rcu_usb_clock_config(uint32_t usb_psc) +{ + uint32_t reg; + + reg = RCU_CFG0; + + /* configure the USBFS prescaler factor */ + reg &= ~RCU_CFG0_USBFSPSC; + RCU_CFG0 = (reg | usb_psc); +} + +/*! + \brief configure the RTC clock source selection + \param[in] rtc_clock_source: RTC clock source selection + only one parameter can be selected which is shown as below: + \arg RCU_RTCSRC_NONE: no clock selected + \arg RCU_RTCSRC_LXTAL: CK_LXTAL selected as RTC source clock + \arg RCU_RTCSRC_IRC40K: CK_IRC40K selected as RTC source clock + \arg RCU_RTCSRC_HXTAL_DIV_128: CK_HXTAL/128 selected as RTC source clock + \param[out] none + \retval none +*/ +void rcu_rtc_clock_config(uint32_t rtc_clock_source) +{ + uint32_t reg; + + reg = RCU_BDCTL; + /* reset the RTCSRC bits and set according to rtc_clock_source */ + reg &= ~RCU_BDCTL_RTCSRC; + RCU_BDCTL = (reg | rtc_clock_source); +} + +/*! + \brief configure the I2S1 clock source selection + \param[in] i2s_clock_source: I2S1 clock source selection + only one parameter can be selected which is shown as below: + \arg RCU_I2S1SRC_CKSYS: System clock selected as I2S1 source clock + \arg RCU_I2S1SRC_CKPLL2_MUL2: CK_PLL2x2 selected as I2S1 source clock + \param[out] none + \retval none +*/ +void rcu_i2s1_clock_config(uint32_t i2s_clock_source) +{ + uint32_t reg; + + reg = RCU_CFG1; + /* reset the I2S1SEL bit and set according to i2s_clock_source */ + reg &= ~RCU_CFG1_I2S1SEL; + RCU_CFG1 = (reg | i2s_clock_source); +} + +/*! + \brief configure the I2S2 clock source selection + \param[in] i2s_clock_source: I2S2 clock source selection + only one parameter can be selected which is shown as below: + \arg RCU_I2S2SRC_CKSYS: system clock selected as I2S2 source clock + \arg RCU_I2S2SRC_CKPLL2_MUL2: CK_PLL2x2 selected as I2S2 source clock + \param[out] none + \retval none +*/ +void rcu_i2s2_clock_config(uint32_t i2s_clock_source) +{ + uint32_t reg; + + reg = RCU_CFG1; + /* reset the I2S2SEL bit and set according to i2s_clock_source */ + reg &= ~RCU_CFG1_I2S2SEL; + RCU_CFG1 = (reg | i2s_clock_source); +} + +/*! + \brief get the clock stabilization and periphral reset flags + \param[in] flag: the clock stabilization and periphral reset flags, refer to rcu_flag_enum + only one parameter can be selected which is shown as below: + \arg RCU_FLAG_IRC8MSTB: IRC8M stabilization flag + \arg RCU_FLAG_HXTALSTB: HXTAL stabilization flag + \arg RCU_FLAG_PLLSTB: PLL stabilization flag + \arg RCU_FLAG_PLL1STB: PLL1 stabilization flag + \arg RCU_FLAG_PLL2STB: PLL2 stabilization flag + \arg RCU_FLAG_LXTALSTB: LXTAL stabilization flag + \arg RCU_FLAG_IRC40KSTB: IRC40K stabilization flag + \arg RCU_FLAG_EPRST: external PIN reset flag + \arg RCU_FLAG_PORRST: power reset flag + \arg RCU_FLAG_SWRST: software reset flag + \arg RCU_FLAG_FWDGTRST: free watchdog timer reset flag + \arg RCU_FLAG_WWDGTRST: window watchdog timer reset flag + \arg RCU_FLAG_LPRST: low-power reset flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus rcu_flag_get(rcu_flag_enum flag) +{ + /* get the rcu flag */ + if(RESET != (RCU_REG_VAL(flag) & BIT(RCU_BIT_POS(flag)))){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear all the reset flag + \param[in] none + \param[out] none + \retval none +*/ +void rcu_all_reset_flag_clear(void) +{ + RCU_RSTSCK |= RCU_RSTSCK_RSTFC; +} + +/*! + \brief get the clock stabilization interrupt and ckm flags + \param[in] int_flag: interrupt and ckm flags, refer to rcu_int_flag_enum + only one parameter can be selected which is shown as below: + \arg RCU_INT_FLAG_IRC40KSTB: IRC40K stabilization interrupt flag + \arg RCU_INT_FLAG_LXTALSTB: LXTAL stabilization interrupt flag + \arg RCU_INT_FLAG_IRC8MSTB: IRC8M stabilization interrupt flag + \arg RCU_INT_FLAG_HXTALSTB: HXTAL stabilization interrupt flag + \arg RCU_INT_FLAG_PLLSTB: PLL stabilization interrupt flag + \arg RCU_INT_FLAG_PLL1STB: PLL1 stabilization interrupt flag + \arg RCU_INT_FLAG_PLL2STB: PLL2 stabilization interrupt flag + \arg RCU_INT_FLAG_CKM: HXTAL clock stuck interrupt flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus rcu_interrupt_flag_get(rcu_int_flag_enum int_flag) +{ + /* get the rcu interrupt flag */ + if(RESET != (RCU_REG_VAL(int_flag) & BIT(RCU_BIT_POS(int_flag)))){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear the interrupt flags + \param[in] int_flag_clear: clock stabilization and stuck interrupt flags clear, refer to rcu_int_flag_clear_enum + only one parameter can be selected which is shown as below: + \arg RCU_INT_FLAG_IRC40KSTB_CLR: IRC40K stabilization interrupt flag clear + \arg RCU_INT_FLAG_LXTALSTB_CLR: LXTAL stabilization interrupt flag clear + \arg RCU_INT_FLAG_IRC8MSTB_CLR: IRC8M stabilization interrupt flag clear + \arg RCU_INT_FLAG_HXTALSTB_CLR: HXTAL stabilization interrupt flag clear + \arg RCU_INT_FLAG_PLLSTB_CLR: PLL stabilization interrupt flag clear + \arg RCU_INT_FLAG_PLL1STB_CLR: PLL1 stabilization interrupt flag clear + \arg RCU_INT_FLAG_PLL2STB_CLR: PLL2 stabilization interrupt flag clear + \arg RCU_INT_FLAG_CKM_CLR: clock stuck interrupt flag clear + \param[out] none + \retval none +*/ +void rcu_interrupt_flag_clear(rcu_int_flag_clear_enum int_flag_clear) +{ + RCU_REG_VAL(int_flag_clear) |= BIT(RCU_BIT_POS(int_flag_clear)); +} + +/*! + \brief enable the stabilization interrupt + \param[in] stab_int: clock stabilization interrupt, refer to rcu_int_enum + Only one parameter can be selected which is shown as below: + \arg RCU_INT_IRC40KSTB: IRC40K stabilization interrupt enable + \arg RCU_INT_LXTALSTB: LXTAL stabilization interrupt enable + \arg RCU_INT_IRC8MSTB: IRC8M stabilization interrupt enable + \arg RCU_INT_HXTALSTB: HXTAL stabilization interrupt enable + \arg RCU_INT_PLLSTB: PLL stabilization interrupt enable + \arg RCU_INT_PLL1STB: PLL1 stabilization interrupt enable + \arg RCU_INT_PLL2STB: PLL2 stabilization interrupt enable + \param[out] none + \retval none +*/ +void rcu_interrupt_enable(rcu_int_enum stab_int) +{ + RCU_REG_VAL(stab_int) |= BIT(RCU_BIT_POS(stab_int)); +} + +/*! + \brief disable the stabilization interrupt + \param[in] stab_int: clock stabilization interrupt, refer to rcu_int_enum + only one parameter can be selected which is shown as below: + \arg RCU_INT_IRC40KSTB: IRC40K stabilization interrupt enable + \arg RCU_INT_LXTALSTB: LXTAL stabilization interrupt enable + \arg RCU_INT_IRC8MSTB: IRC8M stabilization interrupt enable + \arg RCU_INT_HXTALSTB: HXTAL stabilization interrupt enable + \arg RCU_INT_PLLSTB: PLL stabilization interrupt enable + \arg RCU_INT_PLL1STB: PLL1 stabilization interrupt enable + \arg RCU_INT_PLL2STB: PLL2 stabilization interrupt enable + \param[out] none + \retval none +*/ +void rcu_interrupt_disable(rcu_int_enum stab_int) +{ + RCU_REG_VAL(stab_int) &= ~BIT(RCU_BIT_POS(stab_int)); +} + +/*! + \brief wait for oscillator stabilization flags is SET or oscillator startup is timeout + \param[in] osci: oscillator types, refer to rcu_osci_type_enum + only one parameter can be selected which is shown as below: + \arg RCU_HXTAL: high speed crystal oscillator(HXTAL) + \arg RCU_LXTAL: low speed crystal oscillator(LXTAL) + \arg RCU_IRC8M: internal 8M RC oscillators(IRC8M) + \arg RCU_IRC40K: internal 40K RC oscillator(IRC40K) + \arg RCU_PLL_CK: phase locked loop(PLL) + \arg RCU_PLL1_CK: phase locked loop 1 + \arg RCU_PLL2_CK: phase locked loop 2 + \param[out] none + \retval ErrStatus: SUCCESS or ERROR +*/ +ErrStatus rcu_osci_stab_wait(rcu_osci_type_enum osci) +{ + uint32_t stb_cnt = 0U; + ErrStatus reval = ERROR; + FlagStatus osci_stat = RESET; + + switch(osci){ + /* wait HXTAL stable */ + case RCU_HXTAL: + while((RESET == osci_stat) && (HXTAL_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_HXTALSTB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_HXTALSTB)){ + reval = SUCCESS; + } + break; + + /* wait LXTAL stable */ + case RCU_LXTAL: + while((RESET == osci_stat) && (LXTAL_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_LXTALSTB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_LXTALSTB)){ + reval = SUCCESS; + } + break; + + /* wait IRC8M stable */ + case RCU_IRC8M: + while((RESET == osci_stat) && (IRC8M_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_IRC8MSTB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_IRC8MSTB)){ + reval = SUCCESS; + } + break; + + /* wait IRC40K stable */ + case RCU_IRC40K: + while((RESET == osci_stat) && (OSC_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_IRC40KSTB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_IRC40KSTB)){ + reval = SUCCESS; + } + break; + + /* wait PLL stable */ + case RCU_PLL_CK: + while((RESET == osci_stat) && (OSC_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_PLLSTB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_PLLSTB)){ + reval = SUCCESS; + } + break; + /* wait PLL1 stable */ + case RCU_PLL1_CK: + while((RESET == osci_stat) && (OSC_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_PLL1STB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_PLL1STB)){ + reval = SUCCESS; + } + break; + /* wait PLL2 stable */ + case RCU_PLL2_CK: + while((RESET == osci_stat) && (OSC_STARTUP_TIMEOUT != stb_cnt)){ + osci_stat = rcu_flag_get(RCU_FLAG_PLL2STB); + stb_cnt++; + } + + /* check whether flag is set or not */ + if(RESET != rcu_flag_get(RCU_FLAG_PLL2STB)){ + reval = SUCCESS; + } + break; + + default: + break; + } + + /* return value */ + return reval; +} + +/*! + \brief turn on the oscillator + \param[in] osci: oscillator types, refer to rcu_osci_type_enum + only one parameter can be selected which is shown as below: + \arg RCU_HXTAL: high speed crystal oscillator(HXTAL) + \arg RCU_LXTAL: low speed crystal oscillator(LXTAL) + \arg RCU_IRC8M: internal 8M RC oscillators(IRC8M) + \arg RCU_IRC40K: internal 40K RC oscillator(IRC40K) + \arg RCU_PLL_CK: phase locked loop(PLL) + \arg RCU_PLL1_CK: phase locked loop 1 + \arg RCU_PLL2_CK: phase locked loop 2 + \param[out] none + \retval none +*/ +void rcu_osci_on(rcu_osci_type_enum osci) +{ + RCU_REG_VAL(osci) |= BIT(RCU_BIT_POS(osci)); +} + +/*! + \brief turn off the oscillator + \param[in] osci: oscillator types, refer to rcu_osci_type_enum + only one parameter can be selected which is shown as below: + \arg RCU_HXTAL: high speed crystal oscillator(HXTAL) + \arg RCU_LXTAL: low speed crystal oscillator(LXTAL) + \arg RCU_IRC8M: internal 8M RC oscillators(IRC8M) + \arg RCU_IRC40K: internal 40K RC oscillator(IRC40K) + \arg RCU_PLL_CK: phase locked loop(PLL) + \arg RCU_PLL1_CK: phase locked loop 1 + \arg RCU_PLL2_CK: phase locked loop 2 + \param[out] none + \retval none +*/ +void rcu_osci_off(rcu_osci_type_enum osci) +{ + RCU_REG_VAL(osci) &= ~BIT(RCU_BIT_POS(osci)); +} + +/*! + \brief enable the oscillator bypass mode, HXTALEN or LXTALEN must be reset before it + \param[in] osci: oscillator types, refer to rcu_osci_type_enum + only one parameter can be selected which is shown as below: + \arg RCU_HXTAL: high speed crystal oscillator(HXTAL) + \arg RCU_LXTAL: low speed crystal oscillator(LXTAL) + \param[out] none + \retval none +*/ +void rcu_osci_bypass_mode_enable(rcu_osci_type_enum osci) +{ + uint32_t reg; + + switch(osci){ + /* enable HXTAL to bypass mode */ + case RCU_HXTAL: + reg = RCU_CTL; + RCU_CTL &= ~RCU_CTL_HXTALEN; + RCU_CTL = (reg | RCU_CTL_HXTALBPS); + break; + /* enable LXTAL to bypass mode */ + case RCU_LXTAL: + reg = RCU_BDCTL; + RCU_BDCTL &= ~RCU_BDCTL_LXTALEN; + RCU_BDCTL = (reg | RCU_BDCTL_LXTALBPS); + break; + case RCU_IRC8M: + case RCU_IRC40K: + case RCU_PLL_CK: + case RCU_PLL1_CK: + case RCU_PLL2_CK: + break; + default: + break; + } +} + +/*! + \brief disable the oscillator bypass mode, HXTALEN or LXTALEN must be reset before it + \param[in] osci: oscillator types, refer to rcu_osci_type_enum + only one parameter can be selected which is shown as below: + \arg RCU_HXTAL: high speed crystal oscillator(HXTAL) + \arg RCU_LXTAL: low speed crystal oscillator(LXTAL) + \param[out] none + \retval none +*/ +void rcu_osci_bypass_mode_disable(rcu_osci_type_enum osci) +{ + uint32_t reg; + + switch(osci){ + /* disable HXTAL to bypass mode */ + case RCU_HXTAL: + reg = RCU_CTL; + RCU_CTL &= ~RCU_CTL_HXTALEN; + RCU_CTL = (reg & ~RCU_CTL_HXTALBPS); + break; + /* disable LXTAL to bypass mode */ + case RCU_LXTAL: + reg = RCU_BDCTL; + RCU_BDCTL &= ~RCU_BDCTL_LXTALEN; + RCU_BDCTL = (reg & ~RCU_BDCTL_LXTALBPS); + break; + case RCU_IRC8M: + case RCU_IRC40K: + case RCU_PLL_CK: + case RCU_PLL1_CK: + case RCU_PLL2_CK: + break; + default: + break; + } +} + +/*! + \brief enable the HXTAL clock monitor + \param[in] none + \param[out] none + \retval none +*/ + +void rcu_hxtal_clock_monitor_enable(void) +{ + RCU_CTL |= RCU_CTL_CKMEN; +} + +/*! + \brief disable the HXTAL clock monitor + \param[in] none + \param[out] none + \retval none +*/ +void rcu_hxtal_clock_monitor_disable(void) +{ + RCU_CTL &= ~RCU_CTL_CKMEN; +} + +/*! + \brief set the IRC8M adjust value + \param[in] irc8m_adjval: IRC8M adjust value, must be between 0 and 0x1F + \param[out] none + \retval none +*/ +void rcu_irc8m_adjust_value_set(uint32_t irc8m_adjval) +{ + uint32_t reg; + + reg = RCU_CTL; + /* reset the IRC8MADJ bits and set according to irc8m_adjval */ + reg &= ~RCU_CTL_IRC8MADJ; + RCU_CTL = (reg | ((irc8m_adjval & 0x1FU) << 3)); +} + +/*! + \brief deep-sleep mode voltage select + \param[in] dsvol: deep sleep mode voltage + only one parameter can be selected which is shown as below: + \arg RCU_DEEPSLEEP_V_1_2: the core voltage is 1.2V + \arg RCU_DEEPSLEEP_V_1_1: the core voltage is 1.1V + \arg RCU_DEEPSLEEP_V_1_0: the core voltage is 1.0V + \arg RCU_DEEPSLEEP_V_0_9: the core voltage is 0.9V + \param[out] none + \retval none +*/ +void rcu_deepsleep_voltage_set(uint32_t dsvol) +{ + dsvol &= RCU_DSV_DSLPVS; + RCU_DSV = dsvol; +} + +/*! + \brief get the system clock, bus and peripheral clock frequency + \param[in] clock: the clock frequency which to get + only one parameter can be selected which is shown as below: + \arg CK_SYS: system clock frequency + \arg CK_AHB: AHB clock frequency + \arg CK_APB1: APB1 clock frequency + \arg CK_APB2: APB2 clock frequency + \param[out] none + \retval clock frequency of system, AHB, APB1, APB2 +*/ +uint32_t rcu_clock_freq_get(rcu_clock_freq_enum clock) +{ + uint32_t sws, ck_freq = 0U; + uint32_t cksys_freq, ahb_freq, apb1_freq, apb2_freq; + uint32_t pllsel, predv0sel, pllmf,ck_src, idx, clk_exp; + uint32_t predv0, predv1, pll1mf; + + /* exponent of AHB, APB1 and APB2 clock divider */ + uint8_t ahb_exp[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; + uint8_t apb1_exp[8] = {0, 0, 0, 0, 1, 2, 3, 4}; + uint8_t apb2_exp[8] = {0, 0, 0, 0, 1, 2, 3, 4}; + + sws = GET_BITS(RCU_CFG0, 2, 3); + switch(sws){ + /* IRC8M is selected as CK_SYS */ + case SEL_IRC8M: + cksys_freq = IRC8M_VALUE; + break; + /* HXTAL is selected as CK_SYS */ + case SEL_HXTAL: + cksys_freq = HXTAL_VALUE; + break; + /* PLL is selected as CK_SYS */ + case SEL_PLL: + /* PLL clock source selection, HXTAL or IRC8M/2 */ + pllsel = (RCU_CFG0 & RCU_CFG0_PLLSEL); + + if(RCU_PLLSRC_HXTAL == pllsel) { + /* PLL clock source is HXTAL */ + ck_src = HXTAL_VALUE; + + predv0sel = (RCU_CFG1 & RCU_CFG1_PREDV0SEL); + /* source clock use PLL1 */ + if(RCU_PREDV0SRC_CKPLL1 == predv0sel){ + predv1 = (uint32_t)((RCU_CFG1 & RCU_CFG1_PREDV1) >> 4) + 1U; + pll1mf = (uint32_t)((RCU_CFG1 & RCU_CFG1_PLL1MF) >> 8) + 2U; + if(17U == pll1mf){ + pll1mf = 20U; + } + ck_src = (ck_src / predv1) * pll1mf; + } + predv0 = (RCU_CFG1 & RCU_CFG1_PREDV0) + 1U; + ck_src /= predv0; + }else{ + /* PLL clock source is IRC8M/2 */ + ck_src = IRC8M_VALUE/2U; + } + + /* PLL multiplication factor */ + pllmf = GET_BITS(RCU_CFG0, 18, 21); + if((RCU_CFG0 & RCU_CFG0_PLLMF_4)){ + pllmf |= 0x10U; + } + if(pllmf < 15U){ + pllmf += 2U; + }else{ + pllmf += 1U; + } + + cksys_freq = ck_src * pllmf; + + if(15U == pllmf){ + /* PLL source clock multiply by 6.5 */ + cksys_freq = ck_src * 6U + ck_src / 2U; + } + + break; + /* IRC8M is selected as CK_SYS */ + default: + cksys_freq = IRC8M_VALUE; + break; + } + + /* calculate AHB clock frequency */ + idx = GET_BITS(RCU_CFG0, 4, 7); + clk_exp = ahb_exp[idx]; + ahb_freq = cksys_freq >> clk_exp; + + /* calculate APB1 clock frequency */ + idx = GET_BITS(RCU_CFG0, 8, 10); + clk_exp = apb1_exp[idx]; + apb1_freq = ahb_freq >> clk_exp; + + /* calculate APB2 clock frequency */ + idx = GET_BITS(RCU_CFG0, 11, 13); + clk_exp = apb2_exp[idx]; + apb2_freq = ahb_freq >> clk_exp; + + /* return the clocks frequency */ + switch(clock){ + case CK_SYS: + ck_freq = cksys_freq; + break; + case CK_AHB: + ck_freq = ahb_freq; + break; + case CK_APB1: + ck_freq = apb1_freq; + break; + case CK_APB2: + ck_freq = apb2_freq; + break; + default: + break; + } + return ck_freq; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rtc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rtc.c new file mode 100644 index 00000000..e397d3a2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_rtc.c @@ -0,0 +1,273 @@ +/*! + \file gd32vf103_rtc.c + \brief RTC driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_rtc.h" + +/* RTC register high / low bits mask */ +#define RTC_HIGH_BITS_MASK ((uint32_t)0x000F0000U) /* RTC high bits mask */ +#define RTC_LOW_BITS_MASK ((uint32_t)0x0000FFFFU) /* RTC low bits mask */ + +/* RTC register high bits offset */ +#define RTC_HIGH_BITS_OFFSET ((uint32_t)16U) + +/*! + \brief enter RTC configuration mode + \param[in] none + \param[out] none + \retval none +*/ +void rtc_configuration_mode_enter(void) +{ + RTC_CTL |= RTC_CTL_CMF; +} + +/*! + \brief exit RTC configuration mode + \param[in] none + \param[out] none + \retval none +*/ +void rtc_configuration_mode_exit(void) +{ + RTC_CTL &= ~RTC_CTL_CMF; +} + +/*! + \brief set RTC counter value + \param[in] cnt: RTC counter value + \param[out] none + \retval none +*/ +void rtc_counter_set(uint32_t cnt) +{ + rtc_configuration_mode_enter(); + /* set the RTC counter high bits */ + RTC_CNTH = (cnt >> RTC_HIGH_BITS_OFFSET); + /* set the RTC counter low bits */ + RTC_CNTL = (cnt & RTC_LOW_BITS_MASK); + rtc_configuration_mode_exit(); +} + +/*! + \brief set RTC prescaler value + \param[in] psc: RTC prescaler value + \param[out] none + \retval none +*/ +void rtc_prescaler_set(uint32_t psc) +{ + rtc_configuration_mode_enter(); + /* set the RTC prescaler high bits */ + RTC_PSCH = ((psc & RTC_HIGH_BITS_MASK) >> RTC_HIGH_BITS_OFFSET); + /* set the RTC prescaler low bits */ + RTC_PSCL = (psc & RTC_LOW_BITS_MASK); + rtc_configuration_mode_exit(); +} + +/*! + \brief wait RTC last write operation finished flag set + \param[in] none + \param[out] none + \retval none +*/ +void rtc_lwoff_wait(void) +{ + /* loop until LWOFF flag is set */ + while(RESET == (RTC_CTL & RTC_CTL_LWOFF)){ + } +} + +/*! + \brief wait RTC registers synchronized flag set + \param[in] none + \param[out] none + \retval none +*/ +void rtc_register_sync_wait(void) +{ + /* clear RSYNF flag */ + RTC_CTL &= ~RTC_CTL_RSYNF; + /* loop until RSYNF flag is set */ + while(RESET == (RTC_CTL & RTC_CTL_RSYNF)){ + } +} + +/*! + \brief set RTC alarm value + \param[in] alarm: RTC alarm value + \param[out] none + \retval none +*/ +void rtc_alarm_config(uint32_t alarm) +{ + rtc_configuration_mode_enter(); + /* set the alarm high bits */ + RTC_ALRMH = (alarm >> RTC_HIGH_BITS_OFFSET); + /* set the alarm low bits */ + RTC_ALRML = (alarm & RTC_LOW_BITS_MASK); + rtc_configuration_mode_exit(); +} + +/*! + \brief get RTC counter value + \param[in] none + \param[out] none + \retval RTC counter value +*/ +uint32_t rtc_counter_get(void) +{ + uint32_t temp = 0x0U; + + temp = RTC_CNTL; + temp |= (RTC_CNTH << RTC_HIGH_BITS_OFFSET); + return temp; +} + +/*! + \brief get RTC divider value + \param[in] none + \param[out] none + \retval RTC divider value +*/ +uint32_t rtc_divider_get(void) +{ + uint32_t temp = 0x00U; + + temp = ((RTC_DIVH & RTC_DIVH_DIV) << RTC_HIGH_BITS_OFFSET); + temp |= RTC_DIVL; + return temp; +} + +/*! + \brief get RTC flag status + \param[in] flag: specify which flag status to get + only one parameter can be selected which is shown as below: + \arg RTC_FLAG_SECOND: second interrupt flag + \arg RTC_FLAG_ALARM: alarm interrupt flag + \arg RTC_FLAG_OVERFLOW: overflow interrupt flag + \arg RTC_FLAG_RSYN: registers synchronized flag + \arg RTC_FLAG_LWOF: last write operation finished flag + \param[out] none + \retval SET or RESET +*/ +FlagStatus rtc_flag_get(uint32_t flag) +{ + if(RESET != (RTC_CTL & flag)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear RTC flag status + \param[in] flag: specify which flag status to clear + one or more parameters can be selected which are shown as below: + \arg RTC_FLAG_SECOND: second interrupt flag + \arg RTC_FLAG_ALARM: alarm interrupt flag + \arg RTC_FLAG_OVERFLOW: overflow interrupt flag + \arg RTC_FLAG_RSYN: registers synchronized flag + \param[out] none + \retval none +*/ +void rtc_flag_clear(uint32_t flag) +{ + /* clear RTC flag */ + RTC_CTL &= ~flag; +} + +/*! + \brief get RTC interrupt flag status + \param[in] flag: specify which flag status to get + only one parameter can be selected which is shown as below: + \arg RTC_INT_FLAG_SECOND: second interrupt flag + \arg RTC_INT_FLAG_ALARM: alarm interrupt flag + \arg RTC_INT_FLAG_OVERFLOW: overflow interrupt flag + \param[out] none + \retval SET or RESET +*/ +FlagStatus rtc_interrupt_flag_get(uint32_t flag) +{ + if(RESET != (RTC_CTL & flag)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear RTC interrupt flag status + \param[in] flag: specify which flag status to clear + one or more parameters can be selected which are shown as below: + \arg RTC_INT_FLAG_SECOND: second interrupt flag + \arg RTC_INT_FLAG_ALARM: alarm interrupt flag + \arg RTC_INT_FLAG_OVERFLOW: overflow interrupt flag + \param[out] none + \retval none +*/ +void rtc_interrupt_flag_clear(uint32_t flag) +{ + /* clear RTC interrupt flag */ + RTC_CTL &= ~flag; +} + +/*! + \brief enable RTC interrupt + \param[in] interrupt: specify which interrupt to enbale + one or more parameters can be selected which are shown as below: + \arg RTC_INT_SECOND: second interrupt + \arg RTC_INT_ALARM: alarm interrupt + \arg RTC_INT_OVERFLOW: overflow interrupt + \param[out] none + \retval none +*/ +void rtc_interrupt_enable(uint32_t interrupt) +{ + RTC_INTEN |= interrupt; +} + +/*! + \brief disable RTC interrupt + \param[in] interrupt: specify which interrupt to disbale + one or more parameters can be selected which are shown as below: + \arg RTC_INT_SECOND: second interrupt + \arg RTC_INT_ALARM: alarm interrupt + \arg RTC_INT_OVERFLOW: overflow interrupt + \param[out] none + \retval none +*/ +void rtc_interrupt_disable(uint32_t interrupt) +{ + RTC_INTEN &= ~interrupt; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_spi.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_spi.c new file mode 100644 index 00000000..2e1b3a16 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_spi.c @@ -0,0 +1,766 @@ +/*! + \file gd32vf103_spi.c + \brief SPI driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_spi.h" + +/* SPI/I2S parameter initialization mask */ +#define SPI_INIT_MASK ((uint32_t)0x00003040U) /*!< SPI parameter initialization mask */ +#define I2S_INIT_MASK ((uint32_t)0x0000F047U) /*!< I2S parameter initialization mask */ + +/* I2S clock source selection, multiplication and division mask */ +#define I2S1_CLOCK_SEL ((uint32_t)0x00020000U) /* I2S1 clock source selection */ +#define I2S2_CLOCK_SEL ((uint32_t)0x00040000U) /* I2S2 clock source selection */ +#define I2S_CLOCK_MUL_MASK ((uint32_t)0x0000F000U) /* I2S clock multiplication mask */ +#define I2S_CLOCK_DIV_MASK ((uint32_t)0x000000F0U) /* I2S clock division mask */ + +/* default value and offset */ +#define SPI_I2SPSC_DEFAULT_VALUE ((uint32_t)0x00000002U) /* default value of SPI_I2SPSC register */ +#define RCU_CFG1_PREDV1_OFFSET 4U /* PREDV1 offset in RCU_CFG1 */ +#define RCU_CFG1_PLL2MF_OFFSET 12U /* PLL2MF offset in RCU_CFG1 */ + +/*! + \brief reset SPI and I2S + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_i2s_deinit(uint32_t spi_periph) +{ + switch(spi_periph){ + case SPI0: + /* reset SPI0 */ + rcu_periph_reset_enable(RCU_SPI0RST); + rcu_periph_reset_disable(RCU_SPI0RST); + break; + case SPI1: + /* reset SPI1 and I2S1 */ + rcu_periph_reset_enable(RCU_SPI1RST); + rcu_periph_reset_disable(RCU_SPI1RST); + break; + case SPI2: + /* reset SPI2 and I2S2 */ + rcu_periph_reset_enable(RCU_SPI2RST); + rcu_periph_reset_disable(RCU_SPI2RST); + break; + default : + break; + } +} + +/*! + \brief initialize the parameters of SPI struct with the default values + \param[in] spi_struct: SPI parameter stuct + \param[out] none + \retval none +*/ +void spi_struct_para_init(spi_parameter_struct* spi_struct) +{ + /* set the SPI struct with the default values */ + spi_struct->device_mode = SPI_SLAVE; + spi_struct->trans_mode = SPI_TRANSMODE_FULLDUPLEX; + spi_struct->frame_size = SPI_FRAMESIZE_8BIT; + spi_struct->nss = SPI_NSS_HARD; + spi_struct->clock_polarity_phase = SPI_CK_PL_LOW_PH_1EDGE; + spi_struct->prescale = SPI_PSC_2; +} + +/*! + \brief initialize SPI parameter + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] spi_struct: SPI parameter initialization stuct members of the structure + and the member values are shown as below: + device_mode: SPI_MASTER, SPI_SLAVE + trans_mode: SPI_TRANSMODE_FULLDUPLEX, SPI_TRANSMODE_RECEIVEONLY, + SPI_TRANSMODE_BDRECEIVE, SPI_TRANSMODE_BDTRANSMIT + frame_size: SPI_FRAMESIZE_16BIT, SPI_FRAMESIZE_8BIT + nss: SPI_NSS_SOFT, SPI_NSS_HARD + endian: SPI_ENDIAN_MSB, SPI_ENDIAN_LSB + clock_polarity_phase: SPI_CK_PL_LOW_PH_1EDGE, SPI_CK_PL_HIGH_PH_1EDGE + SPI_CK_PL_LOW_PH_2EDGE, SPI_CK_PL_HIGH_PH_2EDGE + prescale: SPI_PSC_n (n=2,4,8,16,32,64,128,256) + \param[out] none + \retval none +*/ +void spi_init(uint32_t spi_periph, spi_parameter_struct* spi_struct) +{ + uint32_t reg = 0U; + reg = SPI_CTL0(spi_periph); + reg &= SPI_INIT_MASK; + + /* select SPI as master or slave */ + reg |= spi_struct->device_mode; + /* select SPI transfer mode */ + reg |= spi_struct->trans_mode; + /* select SPI frame size */ + reg |= spi_struct->frame_size; + /* select SPI NSS use hardware or software */ + reg |= spi_struct->nss; + /* select SPI LSB or MSB */ + reg |= spi_struct->endian; + /* select SPI polarity and phase */ + reg |= spi_struct->clock_polarity_phase; + /* select SPI prescale to adjust transmit speed */ + reg |= spi_struct->prescale; + + /* write to SPI_CTL0 register */ + SPI_CTL0(spi_periph) = (uint32_t)reg; + + SPI_I2SCTL(spi_periph) &= (uint32_t)(~SPI_I2SCTL_I2SSEL); +} + +/*! + \brief enable SPI + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_enable(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_SPIEN; +} + +/*! + \brief disable SPI + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_disable(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_SPIEN); +} + +/*! + \brief initialize I2S parameter + \param[in] spi_periph: SPIx(x=1,2) + \param[in] mode: I2S operation mode + only one parameter can be selected which is shown as below: + \arg I2S_MODE_SLAVETX: I2S slave transmit mode + \arg I2S_MODE_SLAVERX: I2S slave receive mode + \arg I2S_MODE_MASTERTX: I2S master transmit mode + \arg I2S_MODE_MASTERRX: I2S master receive mode + \param[in] standard: I2S standard + only one parameter can be selected which is shown as below: + \arg I2S_STD_PHILLIPS: I2S phillips standard + \arg I2S_STD_MSB: I2S MSB standard + \arg I2S_STD_LSB: I2S LSB standard + \arg I2S_STD_PCMSHORT: I2S PCM short standard + \arg I2S_STD_PCMLONG: I2S PCM long standard + \param[in] ckpl: I2S idle state clock polarity + only one parameter can be selected which is shown as below: + \arg I2S_CKPL_LOW: I2S clock polarity low level + \arg I2S_CKPL_HIGH: I2S clock polarity high level + \param[out] none + \retval none +*/ +void i2s_init(uint32_t spi_periph, uint32_t mode, uint32_t standard, uint32_t ckpl) +{ + uint32_t reg = 0U; + reg = SPI_I2SCTL(spi_periph); + reg &= I2S_INIT_MASK; + + /* enable I2S mode */ + reg |= (uint32_t)SPI_I2SCTL_I2SSEL; + /* select I2S mode */ + reg |= (uint32_t)mode; + /* select I2S standard */ + reg |= (uint32_t)standard; + /* select I2S polarity */ + reg |= (uint32_t)ckpl; + + /* write to SPI_I2SCTL register */ + SPI_I2SCTL(spi_periph) = (uint32_t)reg; +} + +/*! + \brief configure I2S prescaler + \param[in] spi_periph: SPIx(x=1,2) + \param[in] audiosample: I2S audio sample rate + only one parameter can be selected which is shown as below: + \arg I2S_AUDIOSAMPLE_8K: audio sample rate is 8KHz + \arg I2S_AUDIOSAMPLE_11K: audio sample rate is 11KHz + \arg I2S_AUDIOSAMPLE_16K: audio sample rate is 16KHz + \arg I2S_AUDIOSAMPLE_22K: audio sample rate is 22KHz + \arg I2S_AUDIOSAMPLE_32K: audio sample rate is 32KHz + \arg I2S_AUDIOSAMPLE_44K: audio sample rate is 44KHz + \arg I2S_AUDIOSAMPLE_48K: audio sample rate is 48KHz + \arg I2S_AUDIOSAMPLE_96K: audio sample rate is 96KHz + \arg I2S_AUDIOSAMPLE_192K: audio sample rate is 192KHz + \param[in] frameformat: I2S data length and channel length + only one parameter can be selected which is shown as below: + \arg I2S_FRAMEFORMAT_DT16B_CH16B: I2S data length is 16 bit and channel length is 16 bit + \arg I2S_FRAMEFORMAT_DT16B_CH32B: I2S data length is 16 bit and channel length is 32 bit + \arg I2S_FRAMEFORMAT_DT24B_CH32B: I2S data length is 24 bit and channel length is 32 bit + \arg I2S_FRAMEFORMAT_DT32B_CH32B: I2S data length is 32 bit and channel length is 32 bit + \param[in] mckout: I2S master clock output + only one parameter can be selected which is shown as below: + \arg I2S_MCKOUT_ENABLE: I2S master clock output enable + \arg I2S_MCKOUT_DISABLE: I2S master clock output disable + \param[out] none + \retval none +*/ +void i2s_psc_config(uint32_t spi_periph, uint32_t audiosample, uint32_t frameformat, uint32_t mckout) +{ + uint32_t i2sdiv = 2U, i2sof = 0U; + uint32_t clks = 0U; + uint32_t i2sclock = 0U; + + /* deinit SPI_I2SPSC register */ + SPI_I2SPSC(spi_periph) = SPI_I2SPSC_DEFAULT_VALUE; + + /* get the I2S clock source */ + if(SPI1 == ((uint32_t)spi_periph)){ + /* I2S1 clock source selection */ + clks = I2S1_CLOCK_SEL; + }else{ + /* I2S2 clock source selection */ + clks = I2S2_CLOCK_SEL; + } + + if(0U != (RCU_CFG1 & clks)){ + /* get RCU PLL2 clock multiplication factor */ + clks = (uint32_t)((RCU_CFG1 & I2S_CLOCK_MUL_MASK) >> RCU_CFG1_PLL2MF_OFFSET); + + if((clks > 5U) && (clks < 15U)){ + /* multiplier is between 8 and 16 */ + clks += 2U; + }else{ + if(15U == clks){ + /* multiplier is 20 */ + clks = 20U; + } + } + + /* get the PREDV1 value */ + i2sclock = (uint32_t)(((RCU_CFG1 & I2S_CLOCK_DIV_MASK) >> RCU_CFG1_PREDV1_OFFSET) + 1U); + /* calculate I2S clock based on PLL2 and PREDV1 */ + i2sclock = (uint32_t)((HXTAL_VALUE / i2sclock) * clks * 2U); + }else{ + /* get system clock */ + i2sclock = rcu_clock_freq_get(CK_SYS); + } + + /* config the prescaler depending on the mclk output state, the frame format and audio sample rate */ + if(I2S_MCKOUT_ENABLE == mckout){ + clks = (uint32_t)(((i2sclock / 256U) * 10U) / audiosample); + }else{ + if(I2S_FRAMEFORMAT_DT16B_CH16B == frameformat){ + clks = (uint32_t)(((i2sclock / 32U) *10U ) / audiosample); + }else{ + clks = (uint32_t)(((i2sclock / 64U) *10U ) / audiosample); + } + } + + /* remove the floating point */ + clks = (clks + 5U) / 10U; + i2sof = (clks & 0x00000001U); + i2sdiv = ((clks - i2sof) / 2U); + i2sof = (i2sof << 8U); + + /* set the default values */ + if((i2sdiv < 2U) || (i2sdiv > 255U)){ + i2sdiv = 2U; + i2sof = 0U; + } + /* configure SPI_I2SPSC */ + SPI_I2SPSC(spi_periph) = (uint32_t)(i2sdiv | i2sof | mckout); + + /* clear SPI_I2SCTL_DTLEN and SPI_I2SCTL_CHLEN bits */ + SPI_I2SCTL(spi_periph) &= (uint32_t)(~(SPI_I2SCTL_DTLEN | SPI_I2SCTL_CHLEN)); + /* configure data frame format */ + SPI_I2SCTL(spi_periph) |= (uint32_t)frameformat; +} + +/*! + \brief enable I2S + \param[in] spi_periph: SPIx(x=1,2) + \param[out] none + \retval none +*/ +void i2s_enable(uint32_t spi_periph) +{ + SPI_I2SCTL(spi_periph) |= (uint32_t)SPI_I2SCTL_I2SEN; +} + +/*! + \brief disable I2S + \param[in] spi_periph: SPIx(x=1,2) + \param[out] none + \retval none +*/ +void i2s_disable(uint32_t spi_periph) +{ + SPI_I2SCTL(spi_periph) &= (uint32_t)(~SPI_I2SCTL_I2SEN); +} + +/*! + \brief enable SPI NSS output + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_nss_output_enable(uint32_t spi_periph) +{ + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_NSSDRV; +} + +/*! + \brief disable SPI NSS output + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_nss_output_disable(uint32_t spi_periph) +{ + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_NSSDRV); +} + +/*! + \brief SPI NSS pin high level in software mode + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_nss_internal_high(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_SWNSS; +} + +/*! + \brief SPI NSS pin low level in software mode + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_nss_internal_low(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_SWNSS); +} + +/*! + \brief enable SPI DMA send or receive + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] dma: SPI DMA mode + only one parameter can be selected which is shown as below: + \arg SPI_DMA_TRANSMIT: SPI transmit data using DMA + \arg SPI_DMA_RECEIVE: SPI receive data using DMA + \param[out] none + \retval none +*/ +void spi_dma_enable(uint32_t spi_periph, uint8_t dma) +{ + if(SPI_DMA_TRANSMIT == dma){ + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_DMATEN; + }else{ + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_DMAREN; + } +} + +/*! + \brief disable SPI DMA send or receive + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] dma: SPI DMA mode + only one parameter can be selected which is shown as below: + \arg SPI_DMA_TRANSMIT: SPI transmit data using DMA + \arg SPI_DMA_RECEIVE: SPI receive data using DMA + \param[out] none + \retval none +*/ +void spi_dma_disable(uint32_t spi_periph, uint8_t dma) +{ + if(SPI_DMA_TRANSMIT == dma){ + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_DMATEN); + }else{ + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_DMAREN); + } +} + +/*! + \brief configure SPI/I2S data frame format + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] frame_format: SPI frame size + only one parameter can be selected which is shown as below: + \arg SPI_FRAMESIZE_16BIT: SPI frame size is 16 bits + \arg SPI_FRAMESIZE_8BIT: SPI frame size is 8 bits + \param[out] none + \retval none +*/ +void spi_i2s_data_frame_format_config(uint32_t spi_periph, uint16_t frame_format) +{ + /* clear SPI_CTL0_FF16 bit */ + SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_FF16); + /* configure SPI_CTL0_FF16 bit */ + SPI_CTL0(spi_periph) |= (uint32_t)frame_format; +} + +/*! + \brief SPI transmit data + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] data: 16-bit data + \param[out] none + \retval none +*/ +void spi_i2s_data_transmit(uint32_t spi_periph, uint16_t data) +{ + SPI_DATA(spi_periph) = (uint32_t)data; +} + +/*! + \brief SPI receive data + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval 16-bit data +*/ +uint16_t spi_i2s_data_receive(uint32_t spi_periph) +{ + return ((uint16_t)SPI_DATA(spi_periph)); +} + +/*! + \brief configure SPI bidirectional transfer direction + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] transfer_direction: SPI transfer direction + only one parameter can be selected which is shown as below: + \arg SPI_BIDIRECTIONAL_TRANSMIT: SPI work in transmit-only mode + \arg SPI_BIDIRECTIONAL_RECEIVE: SPI work in receive-only mode + \param[out] none + \retval none +*/ +void spi_bidirectional_transfer_config(uint32_t spi_periph, uint32_t transfer_direction) +{ + if(SPI_BIDIRECTIONAL_TRANSMIT == transfer_direction){ + /* set the transmit-only mode */ + SPI_CTL0(spi_periph) |= (uint32_t)SPI_BIDIRECTIONAL_TRANSMIT; + }else{ + /* set the receive-only mode */ + SPI_CTL0(spi_periph) &= SPI_BIDIRECTIONAL_RECEIVE; + } +} + +/*! + \brief set SPI CRC polynomial + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] crc_poly: CRC polynomial value + \param[out] none + \retval none +*/ +void spi_crc_polynomial_set(uint32_t spi_periph,uint16_t crc_poly) +{ + /* enable SPI CRC */ + SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_CRCEN; + + /* set SPI CRC polynomial */ + SPI_CRCPOLY(spi_periph) = (uint32_t)crc_poly; +} + +/*! + \brief get SPI CRC polynomial + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval 16-bit CRC polynomial +*/ +uint16_t spi_crc_polynomial_get(uint32_t spi_periph) +{ + return ((uint16_t)SPI_CRCPOLY(spi_periph)); +} + +/*! + \brief turn on CRC function + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_crc_on(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_CRCEN; +} + +/*! + \brief turn off CRC function + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_crc_off(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_CRCEN); +} + +/*! + \brief SPI next data is CRC value + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_crc_next(uint32_t spi_periph) +{ + SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_CRCNT; +} + +/*! + \brief get SPI CRC send value or receive value + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] crc: SPI crc value + only one parameter can be selected which is shown as below: + \arg SPI_CRC_TX: get transmit crc value + \arg SPI_CRC_RX: get receive crc value + \param[out] none + \retval 16-bit CRC value +*/ +uint16_t spi_crc_get(uint32_t spi_periph,uint8_t crc) +{ + if(SPI_CRC_TX == crc){ + return ((uint16_t)(SPI_TCRC(spi_periph))); + }else{ + return ((uint16_t)(SPI_RCRC(spi_periph))); + } +} + +/*! + \brief enable SPI TI mode + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_ti_mode_enable(uint32_t spi_periph) +{ + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_TMOD; +} + +/*! + \brief disable SPI TI mode + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_ti_mode_disable(uint32_t spi_periph) +{ + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_TMOD); +} + +/*! + \brief enable SPI NSS pulse mode + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_nssp_mode_enable(uint32_t spi_periph) +{ + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_NSSP; +} + +/*! + \brief disable SPI NSS pulse mode + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_nssp_mode_disable(uint32_t spi_periph) +{ + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_NSSP); +} + + +/*! + \brief enable SPI and I2S interrupt + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] interrupt: SPI/I2S interrupt + only one parameter can be selected which is shown as below: + \arg SPI_I2S_INT_TBE: transmit buffer empty interrupt + \arg SPI_I2S_INT_RBNE: receive buffer not empty interrupt + \arg SPI_I2S_INT_ERR: CRC error,configuration error,reception overrun error, + transmission underrun error and format error interrupt + \param[out] none + \retval none +*/ +void spi_i2s_interrupt_enable(uint32_t spi_periph, uint8_t interrupt) +{ + switch(interrupt){ + /* SPI/I2S transmit buffer empty interrupt */ + case SPI_I2S_INT_TBE: + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_TBEIE; + break; + /* SPI/I2S receive buffer not empty interrupt */ + case SPI_I2S_INT_RBNE: + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_RBNEIE; + break; + /* SPI/I2S error */ + case SPI_I2S_INT_ERR: + SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_ERRIE; + break; + default: + break; + } +} + +/*! + \brief disable SPI and I2S interrupt + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] interrupt: SPI/I2S interrupt + only one parameter can be selected which is shown as below: + \arg SPI_I2S_INT_TBE: transmit buffer empty interrupt + \arg SPI_I2S_INT_RBNE: receive buffer not empty interrupt + \arg SPI_I2S_INT_ERR: CRC error,configuration error,reception overrun error, + transmission underrun error and format error interrupt + \param[out] none + \retval none +*/ +void spi_i2s_interrupt_disable(uint32_t spi_periph, uint8_t interrupt) +{ + switch(interrupt){ + /* SPI/I2S transmit buffer empty interrupt */ + case SPI_I2S_INT_TBE: + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_TBEIE); + break; + /* SPI/I2S receive buffer not empty interrupt */ + case SPI_I2S_INT_RBNE: + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_RBNEIE); + break; + /* SPI/I2S error */ + case SPI_I2S_INT_ERR: + SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_ERRIE); + break; + default: + break; + } +} + +/*! + \brief get SPI and I2S interrupt flag status + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] interrupt: SPI/I2S interrupt flag status + only one parameter can be selected which is shown as below: + \arg SPI_I2S_INT_FLAG_TBE: transmit buffer empty interrupt flag + \arg SPI_I2S_INT_FLAG_RBNE: receive buffer not empty interrupt flag + \arg SPI_I2S_INT_FLAG_RXORERR: overrun interrupt flag + \arg SPI_INT_FLAG_CONFERR: config error interrupt flag + \arg SPI_INT_FLAG_CRCERR: CRC error interrupt flag + \arg I2S_INT_FLAG_TXURERR: underrun error interrupt flag + \arg SPI_I2S_INT_FLAG_FERR: format error interrupt flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus spi_i2s_interrupt_flag_get(uint32_t spi_periph, uint8_t interrupt) +{ + uint32_t reg1 = SPI_STAT(spi_periph); + uint32_t reg2 = SPI_CTL1(spi_periph); + + switch(interrupt){ + /* SPI/I2S transmit buffer empty interrupt */ + case SPI_I2S_INT_FLAG_TBE: + reg1 = reg1 & SPI_STAT_TBE; + reg2 = reg2 & SPI_CTL1_TBEIE; + break; + /* SPI/I2S receive buffer not empty interrupt */ + case SPI_I2S_INT_FLAG_RBNE: + reg1 = reg1 & SPI_STAT_RBNE; + reg2 = reg2 & SPI_CTL1_RBNEIE; + break; + /* SPI/I2S overrun interrupt */ + case SPI_I2S_INT_FLAG_RXORERR: + reg1 = reg1 & SPI_STAT_RXORERR; + reg2 = reg2 & SPI_CTL1_ERRIE; + break; + /* SPI config error interrupt */ + case SPI_INT_FLAG_CONFERR: + reg1 = reg1 & SPI_STAT_CONFERR; + reg2 = reg2 & SPI_CTL1_ERRIE; + break; + /* SPI CRC error interrupt */ + case SPI_INT_FLAG_CRCERR: + reg1 = reg1 & SPI_STAT_CRCERR; + reg2 = reg2 & SPI_CTL1_ERRIE; + break; + /* I2S underrun error interrupt */ + case I2S_INT_FLAG_TXURERR: + reg1 = reg1 & SPI_STAT_TXURERR; + reg2 = reg2 & SPI_CTL1_ERRIE; + break; + /* SPI/I2S format error interrupt */ + case SPI_I2S_INT_FLAG_FERR: + reg1 = reg1 & SPI_STAT_FERR; + reg2 = reg2 & SPI_CTL1_ERRIE; + break; + default: + break; + } + /* get SPI/I2S interrupt flag status */ + if((0U != reg1) && (0U != reg2)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief get SPI and I2S flag status + \param[in] spi_periph: SPIx(x=0,1,2) + \param[in] flag: SPI/I2S flag status + one or more parameters can be selected which are shown as below: + \arg SPI_FLAG_TBE: transmit buffer empty flag + \arg SPI_FLAG_RBNE: receive buffer not empty flag + \arg SPI_FLAG_TRANS: transmit on-going flag + \arg SPI_FLAG_RXORERR: receive overrun error flag + \arg SPI_FLAG_CONFERR: mode config error flag + \arg SPI_FLAG_CRCERR: CRC error flag + \arg SPI_FLAG_FERR: format error interrupt flag + \arg I2S_FLAG_TBE: transmit buffer empty flag + \arg I2S_FLAG_RBNE: receive buffer not empty flag + \arg I2S_FLAG_TRANS: transmit on-going flag + \arg I2S_FLAG_RXORERR: overrun error flag + \arg I2S_FLAG_TXURERR: underrun error flag + \arg I2S_FLAG_CH: channel side flag + \arg I2S_FLAG_FERR: format error interrupt flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus spi_i2s_flag_get(uint32_t spi_periph, uint32_t flag) +{ + if(RESET != (SPI_STAT(spi_periph) & flag)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear SPI CRC error flag status + \param[in] spi_periph: SPIx(x=0,1,2) + \param[out] none + \retval none +*/ +void spi_crc_error_clear(uint32_t spi_periph) +{ + SPI_STAT(spi_periph) &= (uint32_t)(~SPI_FLAG_CRCERR); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_timer.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_timer.c new file mode 100644 index 00000000..dd53c24b --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_timer.c @@ -0,0 +1,1967 @@ +/*! + \file gd32vf103_timer.c + \brief TIMER driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ +#include "gd32vf103_timer.h" + +/* TIMER init parameter mask */ +#define ALIGNEDMODE_MASK ((uint32_t)0x00000060U) /*!< TIMER init parameter aligne dmode mask */ +#define COUNTERDIRECTION_MASK ((uint32_t)0x00000010U) /*!< TIMER init parameter counter direction mask */ +#define CLOCKDIVISION_MASK ((uint32_t)0x00000300U) /*!< TIMER init parameter clock division value mask */ + +/*! + \brief deinit a timer + \param[in] timer_periph: TIMERx(x=0..13) + \param[out] none + \retval none +*/ +void timer_deinit(uint32_t timer_periph) +{ + switch(timer_periph){ + case TIMER0: + /* reset TIMER0 */ + rcu_periph_reset_enable(RCU_TIMER0RST); + rcu_periph_reset_disable(RCU_TIMER0RST); + break; + case TIMER1: + /* reset TIMER1 */ + rcu_periph_reset_enable(RCU_TIMER1RST); + rcu_periph_reset_disable(RCU_TIMER1RST); + break; + case TIMER2: + /* reset TIMER2 */ + rcu_periph_reset_enable(RCU_TIMER2RST); + rcu_periph_reset_disable(RCU_TIMER2RST); + break; + case TIMER3: + /* reset TIMER3 */ + rcu_periph_reset_enable(RCU_TIMER3RST); + rcu_periph_reset_disable(RCU_TIMER3RST); + break; + case TIMER4: + /* reset TIMER4 */ + rcu_periph_reset_enable(RCU_TIMER4RST); + rcu_periph_reset_disable(RCU_TIMER4RST); + break; + case TIMER5: + /* reset TIMER5 */ + rcu_periph_reset_enable(RCU_TIMER5RST); + rcu_periph_reset_disable(RCU_TIMER5RST); + break; + case TIMER6: + /* reset TIMER6 */ + rcu_periph_reset_enable(RCU_TIMER6RST); + rcu_periph_reset_disable(RCU_TIMER6RST); + break; + + default: + break; + } +} + +/*! + \brief initialize TIMER init parameter struct with a default value + \param[in] initpara: init parameter struct + \param[out] none + \retval none +*/ +void timer_struct_para_init(timer_parameter_struct* initpara) +{ + /* initialize the init parameter struct member with the default value */ + initpara->prescaler = 0U; + initpara->alignedmode = TIMER_COUNTER_EDGE; + initpara->counterdirection = TIMER_COUNTER_UP; + initpara->period = 65535U; + initpara->clockdivision = TIMER_CKDIV_DIV1; + initpara->repetitioncounter = 0U; +} + +/*! + \brief initialize TIMER counter + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] initpara: init parameter struct + prescaler: prescaler value of the counter clock, 0~65535 + alignedmode: TIMER_COUNTER_EDGE, TIMER_COUNTER_CENTER_DOWN, TIMER_COUNTER_CENTER_UP, + TIMER_COUNTER_CENTER_BOTH + counterdirection: TIMER_COUNTER_UP, TIMER_COUNTER_DOWN + period: counter auto reload value, 0~65535 + clockdivision: TIMER_CKDIV_DIV1, TIMER_CKDIV_DIV2, TIMER_CKDIV_DIV4 + repetitioncounter: counter repetition value, 0~255 + \param[out] none + \retval none +*/ +void timer_init(uint32_t timer_periph, timer_parameter_struct* initpara) +{ + /* configure the counter prescaler value */ + TIMER_PSC(timer_periph) = (uint16_t)initpara->prescaler; + + /* configure the counter direction and aligned mode */ + if((TIMER0 == timer_periph) || (TIMER1 == timer_periph) || (TIMER2 == timer_periph) + || (TIMER3 == timer_periph) || (TIMER4 == timer_periph) ){ + TIMER_CTL0(timer_periph) &= (~(uint32_t)(TIMER_CTL0_DIR | TIMER_CTL0_CAM)); + TIMER_CTL0(timer_periph) |= (uint32_t)(initpara->alignedmode & ALIGNEDMODE_MASK); + TIMER_CTL0(timer_periph) |= (uint32_t)(initpara->counterdirection & COUNTERDIRECTION_MASK); + }else{ + TIMER_CTL0(timer_periph) &= (uint32_t)(~ TIMER_CTL0_DIR); + TIMER_CTL0(timer_periph) |= (uint32_t)(initpara->counterdirection & COUNTERDIRECTION_MASK); + } + + /* configure the autoreload value */ + TIMER_CAR(timer_periph) = (uint32_t)initpara->period; + + if((TIMER5 != timer_periph) && (TIMER6 != timer_periph)){ + /* reset the CKDIV bit */ + TIMER_CTL0(timer_periph) &= (~(uint32_t)TIMER_CTL0_CKDIV); + TIMER_CTL0(timer_periph) |= (uint32_t)(initpara->clockdivision & CLOCKDIVISION_MASK); + } + + if (TIMER0 == timer_periph) { + /* configure the repetition counter value */ + TIMER_CREP(timer_periph) = (uint32_t)initpara->repetitioncounter; + } + + /* generate an update event */ + TIMER_SWEVG(timer_periph) |= (uint32_t)TIMER_SWEVG_UPG; +} + +/*! + \brief enable a timer + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval none +*/ +void timer_enable(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) |= (uint32_t)TIMER_CTL0_CEN; +} + +/*! + \brief disable a timer + \param[in] timer_periph: TIMERx(x=0..13) + \param[out] none + \retval none +*/ +void timer_disable(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) &= ~(uint32_t)TIMER_CTL0_CEN; +} + +/*! + \brief enable the auto reload shadow function + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval none +*/ +void timer_auto_reload_shadow_enable(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) |= (uint32_t)TIMER_CTL0_ARSE; +} + +/*! + \brief disable the auto reload shadow function + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval none +*/ +void timer_auto_reload_shadow_disable(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) &= ~(uint32_t)TIMER_CTL0_ARSE; +} + +/*! + \brief enable the update event + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval none +*/ +void timer_update_event_enable(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) &= ~(uint32_t)TIMER_CTL0_UPDIS; +} + +/*! + \brief disable the update event + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval none +*/ +void timer_update_event_disable(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) |= (uint32_t) TIMER_CTL0_UPDIS; +} + +/*! + \brief set TIMER counter alignment mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] aligned: + only one parameter can be selected which is shown as below: + \arg TIMER_COUNTER_EDGE: edge-aligned mode + \arg TIMER_COUNTER_CENTER_DOWN: center-aligned and counting down assert mode + \arg TIMER_COUNTER_CENTER_UP: center-aligned and counting up assert mode + \arg TIMER_COUNTER_CENTER_BOTH: center-aligned and counting up/down assert mode + \param[out] none + \retval none +*/ +void timer_counter_alignment(uint32_t timer_periph, uint16_t aligned) +{ + TIMER_CTL0(timer_periph) &= (uint32_t)(~TIMER_CTL0_CAM); + TIMER_CTL0(timer_periph) |= (uint32_t)aligned; +} + +/*! + \brief set TIMER counter up direction + \param[in] timer_periph: TIMERx(x=0..4) + \param[out] none + \retval none +*/ +void timer_counter_up_direction(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) &= ~(uint32_t)TIMER_CTL0_DIR; +} + +/*! + \brief set TIMER counter down direction + \param[in] timer_periph: TIMERx(x=0..4) + \param[out] none + \retval none +*/ +void timer_counter_down_direction(uint32_t timer_periph) +{ + TIMER_CTL0(timer_periph) |= (uint32_t)TIMER_CTL0_DIR; +} + +/*! + \brief configure TIMER prescaler + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] prescaler: prescaler value + \param[in] pscreload: prescaler reload mode + only one parameter can be selected which is shown as below: + \arg TIMER_PSC_RELOAD_NOW: the prescaler is loaded right now + \arg TIMER_PSC_RELOAD_UPDATE: the prescaler is loaded at the next update event + \param[out] none + \retval none +*/ +void timer_prescaler_config(uint32_t timer_periph, uint16_t prescaler, uint32_t pscreload) +{ + TIMER_PSC(timer_periph) = (uint32_t)prescaler; + + if(TIMER_PSC_RELOAD_NOW == pscreload){ + TIMER_SWEVG(timer_periph) |= (uint32_t)TIMER_SWEVG_UPG; + } +} + +/*! + \brief configure TIMER repetition register value + \param[in] timer_periph: TIMERx(x=0) + \param[in] repetition: the counter repetition value, 0~255 + \param[out] none + \retval none +*/ +void timer_repetition_value_config(uint32_t timer_periph, uint16_t repetition) +{ + TIMER_CREP(timer_periph) = (uint32_t)repetition; +} + +/*! + \brief configure TIMER autoreload register value + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] autoreload: the counter auto-reload value + \param[out] none + \retval none +*/ +void timer_autoreload_value_config(uint32_t timer_periph, uint16_t autoreload) +{ + TIMER_CAR(timer_periph) = (uint32_t)autoreload; +} + +/*! + \brief configure TIMER counter register value + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] counter: the counter value + \param[out] none + \retval none +*/ +void timer_counter_value_config(uint32_t timer_periph, uint16_t counter) +{ + TIMER_CNT(timer_periph) = (uint32_t)counter; +} + +/*! + \brief read TIMER counter value + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval counter value +*/ +uint32_t timer_counter_read(uint32_t timer_periph) +{ + uint32_t count_value = 0U; + count_value = TIMER_CNT(timer_periph); + return (count_value); +} + +/*! + \brief read TIMER prescaler value + \param[in] timer_periph: TIMERx(x=0..6) + \param[out] none + \retval prescaler register value +*/ +uint16_t timer_prescaler_read(uint32_t timer_periph) +{ + uint16_t prescaler_value = 0U; + prescaler_value = (uint16_t) (TIMER_PSC(timer_periph)); + return (prescaler_value); +} + +/*! + \brief configure TIMER single pulse mode + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] spmode: + only one parameter can be selected which is shown as below: + \arg TIMER_SP_MODE_SINGLE: single pulse mode + \arg TIMER_SP_MODE_REPETITIVE: repetitive pulse mode + \param[out] none + \retval none +*/ +void timer_single_pulse_mode_config(uint32_t timer_periph, uint32_t spmode) +{ + if(TIMER_SP_MODE_SINGLE == spmode){ + TIMER_CTL0(timer_periph) |= (uint32_t)TIMER_CTL0_SPM; + }else if(TIMER_SP_MODE_REPETITIVE == spmode){ + TIMER_CTL0(timer_periph) &= ~((uint32_t)TIMER_CTL0_SPM); + }else{ + /* illegal parameters */ + } +} + +/*! + \brief configure TIMER update source + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] update: + only one parameter can be selected which is shown as below: + \arg TIMER_UPDATE_SRC_GLOBAL: update generate by setting of UPG bit or the counter overflow/underflow, + or the slave mode controller trigger + \arg TIMER_UPDATE_SRC_REGULAR: update generate only by counter overflow/underflow + \param[out] none + \retval none +*/ +void timer_update_source_config(uint32_t timer_periph, uint32_t update) +{ + if(TIMER_UPDATE_SRC_REGULAR == update){ + TIMER_CTL0(timer_periph) |= (uint32_t)TIMER_CTL0_UPS; + }else if(TIMER_UPDATE_SRC_GLOBAL == update){ + TIMER_CTL0(timer_periph) &= ~(uint32_t)TIMER_CTL0_UPS; + }else{ + /* illegal parameters */ + } +} + +/*! + \brief enable the TIMER DMA + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] dma: specify which DMA to enable + one or more parameters can be selected which are shown as below: + \arg TIMER_DMA_UPD: update DMA enable, TIMERx(x=0..6) + \arg TIMER_DMA_CH0D: channel 0 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CH1D: channel 1 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CH2D: channel 2 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CH3D: channel 3 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CMTD: channel commutation DMA request enable, TIMERx(x=0) + \arg TIMER_DMA_TRGD: trigger DMA enable, TIMERx(x=0..4) + \param[out] none + \retval none +*/ +void timer_dma_enable(uint32_t timer_periph, uint16_t dma) +{ + TIMER_DMAINTEN(timer_periph) |= (uint32_t) dma; +} + +/*! + \brief disable the TIMER DMA + \param[in] timer_periph: TIMERxTIMERx(x=0..6) + \param[in] dma: specify which DMA to disbale + one or more parameters can be selected which are shown as below: + \arg TIMER_DMA_UPD: update DMA enable, TIMERx(x=0..6) + \arg TIMER_DMA_CH0D: channel 0 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CH1D: channel 1 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CH2D: channel 2 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CH3D: channel 3 DMA enable, TIMERx(x=0..4) + \arg TIMER_DMA_CMTD: channel commutation DMA request enable, TIMERx(x=0) + \arg TIMER_DMA_TRGD: trigger DMA enable, TIMERx(x=0..4,7) + \param[out] none + \retval none +*/ +void timer_dma_disable(uint32_t timer_periph, uint16_t dma) +{ + TIMER_DMAINTEN(timer_periph) &= (~(uint32_t)(dma)); +} + +/*! + \brief channel DMA request source selection + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] dma_request: channel DMA request source selection + only one parameter can be selected which is shown as below: + \arg TIMER_DMAREQUEST_CHANNELEVENT: DMA request of channel n is sent when channel n event occurs + \arg TIMER_DMAREQUEST_UPDATEEVENT: DMA request of channel n is sent when update event occurs + \param[out] none + \retval none +*/ +void timer_channel_dma_request_source_select(uint32_t timer_periph, uint32_t dma_request) +{ + if(TIMER_DMAREQUEST_UPDATEEVENT == dma_request){ + TIMER_CTL1(timer_periph) |= (uint32_t)TIMER_CTL1_DMAS; + }else if(TIMER_DMAREQUEST_CHANNELEVENT == dma_request){ + TIMER_CTL1(timer_periph) &= ~(uint32_t)TIMER_CTL1_DMAS; + }else{ + /* illegal parameters */ + } +} + +/*! + \brief configure the TIMER DMA transfer + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] dma_baseaddr: + only one parameter can be selected which is shown as below: + \arg TIMER_DMACFG_DMATA_CTL0: DMA transfer address is TIMER_CTL0, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CTL1: DMA transfer address is TIMER_CTL1, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_SMCFG: DMA transfer address is TIMER_SMCFG, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_DMAINTEN: DMA transfer address is TIMER_DMAINTEN, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_INTF: DMA transfer address is TIMER_INTF, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_SWEVG: DMA transfer address is TIMER_SWEVG, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CHCTL0: DMA transfer address is TIMER_CHCTL0, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CHCTL1: DMA transfer address is TIMER_CHCTL1, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CHCTL2: DMA transfer address is TIMER_CHCTL2, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CNT: DMA transfer address is TIMER_CNT, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_PSC: DMA transfer address is TIMER_PSC, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CAR: DMA transfer address is TIMER_CAR, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CREP: DMA transfer address is TIMER_CREP, TIMERx(x=0) + \arg TIMER_DMACFG_DMATA_CH0CV: DMA transfer address is TIMER_CH0CV, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CH1CV: DMA transfer address is TIMER_CH1CV, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CH2CV: DMA transfer address is TIMER_CH2CV, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CH3CV: DMA transfer address is TIMER_CH3CV, TIMERx(x=0..4) + \arg TIMER_DMACFG_DMATA_CCHP: DMA transfer address is TIMER_CCHP, TIMERx(x=0) + \arg TIMER_DMACFG_DMATA_DMACFG: DMA transfer address is TIMER_DMACFG, TIMERx(x=0..4) + \param[in] dma_lenth: + only one parameter can be selected which is shown as below: + \arg TIMER_DMACFG_DMATC_xTRANSFER(x=1..6): DMA transfer x time + \param[out] none + \retval none +*/ +void timer_dma_transfer_config(uint32_t timer_periph, uint32_t dma_baseaddr, uint32_t dma_lenth) +{ + TIMER_DMACFG(timer_periph) &= (~(uint32_t)(TIMER_DMACFG_DMATA | TIMER_DMACFG_DMATC)); + TIMER_DMACFG(timer_periph) |= (uint32_t)(dma_baseaddr | dma_lenth); +} + +/*! + \brief software generate events + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] event: the timer software event generation sources + one or more parameters can be selected which are shown as below: + \arg TIMER_EVENT_SRC_UPG: update event generation, TIMERx(x=0..6) + \arg TIMER_EVENT_SRC_CH0G: channel 0 capture or compare event generation, TIMERx(x=0..4) + \arg TIMER_EVENT_SRC_CH1G: channel 1 capture or compare event generation, TIMERx(x=0..4) + \arg TIMER_EVENT_SRC_CH2G: channel 2 capture or compare event generation, TIMERx(x=0..4) + \arg TIMER_EVENT_SRC_CH3G: channel 3 capture or compare event generation, TIMERx(x=0..4) + \arg TIMER_EVENT_SRC_CMTG: channel commutation event generation, TIMERx(x=0) + \arg TIMER_EVENT_SRC_TRGG: trigger event generation, TIMERx(x=0..4) + \arg TIMER_EVENT_SRC_BRKG: break event generation, TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_event_software_generate(uint32_t timer_periph, uint16_t event) +{ + TIMER_SWEVG(timer_periph) |= (uint32_t)event; +} + +/*! + \brief initialize TIMER break parameter struct with a default value + \param[in] breakpara: TIMER break parameter struct + \param[out] none + \retval none +*/ +void timer_break_struct_para_init(timer_break_parameter_struct* breakpara) +{ + /* initialize the break parameter struct member with the default value */ + breakpara->runoffstate = TIMER_ROS_STATE_DISABLE; + breakpara->ideloffstate = TIMER_IOS_STATE_DISABLE; + breakpara->deadtime = 0U; + breakpara->breakpolarity = TIMER_BREAK_POLARITY_LOW; + breakpara->outputautostate = TIMER_OUTAUTO_DISABLE; + breakpara->protectmode = TIMER_CCHP_PROT_OFF; + breakpara->breakstate = TIMER_BREAK_DISABLE; +} + +/*! + \brief configure TIMER break function + \param[in] timer_periph: TIMERx(x=0) + \param[in] breakpara: TIMER break parameter struct + runoffstate: TIMER_ROS_STATE_ENABLE, TIMER_ROS_STATE_DISABLE + ideloffstate: TIMER_IOS_STATE_ENABLE, TIMER_IOS_STATE_DISABLE + deadtime: 0~255 + breakpolarity: TIMER_BREAK_POLARITY_LOW, TIMER_BREAK_POLARITY_HIGH + outputautostate: TIMER_OUTAUTO_ENABLE, TIMER_OUTAUTO_DISABLE + protectmode: TIMER_CCHP_PROT_OFF, TIMER_CCHP_PROT_0, TIMER_CCHP_PROT_1, TIMER_CCHP_PROT_2 + breakstate: TIMER_BREAK_ENABLE, TIMER_BREAK_DISABLE + \param[out] none + \retval none +*/ +void timer_break_config(uint32_t timer_periph, timer_break_parameter_struct* breakpara) +{ + TIMER_CCHP(timer_periph) = (uint32_t)(((uint32_t)(breakpara->runoffstate)) | + ((uint32_t)(breakpara->ideloffstate))| + ((uint32_t)(breakpara->deadtime)) | + ((uint32_t)(breakpara->breakpolarity)) | + ((uint32_t)(breakpara->outputautostate)) | + ((uint32_t)(breakpara->protectmode)) | + ((uint32_t)(breakpara->breakstate))); +} + +/*! + \brief enable TIMER break function + \param[in] timer_periph: TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_break_enable(uint32_t timer_periph) +{ + TIMER_CCHP(timer_periph) |= (uint32_t)TIMER_CCHP_BRKEN; +} + +/*! + \brief disable TIMER break function + \param[in] timer_periph: TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_break_disable(uint32_t timer_periph) +{ + TIMER_CCHP(timer_periph) &= ~(uint32_t)TIMER_CCHP_BRKEN; +} + +/*! + \brief enable TIMER output automatic function + \param[in] timer_periph: TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_automatic_output_enable(uint32_t timer_periph) +{ + TIMER_CCHP(timer_periph) |= (uint32_t)TIMER_CCHP_OAEN; +} + +/*! + \brief disable TIMER output automatic function + \param[in] timer_periph: TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_automatic_output_disable(uint32_t timer_periph) +{ + TIMER_CCHP(timer_periph) &= ~(uint32_t)TIMER_CCHP_OAEN; +} + +/*! + \brief enable or disable TIMER primary output function + \param[in] timer_periph: TIMERx(x=0) + \param[in] newvalue: ENABLE or DISABLE + \param[out] none + \retval none +*/ +void timer_primary_output_config(uint32_t timer_periph, ControlStatus newvalue) +{ + if(ENABLE == newvalue){ + TIMER_CCHP(timer_periph) |= (uint32_t)TIMER_CCHP_POEN; + }else{ + TIMER_CCHP(timer_periph) &= (~(uint32_t)TIMER_CCHP_POEN); + } +} + +/*! + \brief enable or disable channel capture/compare control shadow register + \param[in] timer_periph: TIMERx(x=0) + \param[in] newvalue: ENABLE or DISABLE + \param[out] none + \retval none +*/ +void timer_channel_control_shadow_config(uint32_t timer_periph, ControlStatus newvalue) +{ + if(ENABLE == newvalue){ + TIMER_CTL1(timer_periph) |= (uint32_t)TIMER_CTL1_CCSE; + }else{ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_CCSE); + } +} + +/*! + \brief configure TIMER channel control shadow register update control + \param[in] timer_periph: TIMERx(x=0) + \param[in] ccuctl: channel control shadow register update control + only one parameter can be selected which is shown as below: + \arg TIMER_UPDATECTL_CCU: the shadow registers update by when CMTG bit is set + \arg TIMER_UPDATECTL_CCUTRI: the shadow registers update by when CMTG bit is set or an rising edge of TRGI occurs + \param[out] none + \retval none +*/ +void timer_channel_control_shadow_update_config(uint32_t timer_periph, uint32_t ccuctl) +{ + if(TIMER_UPDATECTL_CCU == ccuctl){ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_CCUC); + }else if(TIMER_UPDATECTL_CCUTRI == ccuctl){ + TIMER_CTL1(timer_periph) |= (uint32_t)TIMER_CTL1_CCUC; + }else{ + /* illegal parameters */ + } +} + +/*! + \brief initialize TIMER channel output parameter struct with a default value + \param[in] ocpara: TIMER channel n output parameter struct + \param[out] none + \retval none +*/ +void timer_channel_output_struct_para_init(timer_oc_parameter_struct* ocpara) +{ + /* initialize the channel output parameter struct member with the default value */ + ocpara->outputstate = TIMER_CCX_DISABLE; + ocpara->outputnstate = TIMER_CCXN_DISABLE; + ocpara->ocpolarity = TIMER_OC_POLARITY_HIGH; + ocpara->ocnpolarity = TIMER_OCN_POLARITY_HIGH; + ocpara->ocidlestate = TIMER_OC_IDLE_STATE_LOW; + ocpara->ocnidlestate = TIMER_OCN_IDLE_STATE_LOW; +} + +/*! + \brief configure TIMER channel output function + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] ocpara: TIMER channeln output parameter struct + outputstate: TIMER_CCX_ENABLE, TIMER_CCX_DISABLE + outputnstate: TIMER_CCXN_ENABLE, TIMER_CCXN_DISABLE + ocpolarity: TIMER_OC_POLARITY_HIGH, TIMER_OC_POLARITY_LOW + ocnpolarity: TIMER_OCN_POLARITY_HIGH, TIMER_OCN_POLARITY_LOW + ocidlestate: TIMER_OC_IDLE_STATE_LOW, TIMER_OC_IDLE_STATE_HIGH + ocnidlestate: TIMER_OCN_IDLE_STATE_LOW, TIMER_OCN_IDLE_STATE_HIGH + \param[out] none + \retval none +*/ +void timer_channel_output_config(uint32_t timer_periph, uint16_t channel, timer_oc_parameter_struct* ocpara) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + /* reset the CH0EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0EN); + /* set the CH0EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocpara->outputstate; + /* reset the CH0P bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0P); + /* set the CH0P bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocpara->ocpolarity; + + if (TIMER0 == timer_periph) { + /* reset the CH0NEN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0NEN); + /* set the CH0NEN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocpara->outputnstate; + /* reset the CH0NP bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0NP); + /* set the CH0NP bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocpara->ocnpolarity; + /* reset the ISO0 bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO0); + /* set the ISO0 bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)ocpara->ocidlestate; + /* reset the ISO0N bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO0N); + /* set the ISO0N bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)ocpara->ocnidlestate; + } + TIMER_CHCTL0(timer_periph) &= ~(uint32_t)TIMER_CHCTL0_CH0MS; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + /* reset the CH1EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1EN); + /* set the CH1EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->outputstate) << 4U); + /* reset the CH1P bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1P); + /* set the CH1P bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocpolarity) << 4U); + + if (TIMER0 == timer_periph) { + /* reset the CH1NEN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1NEN); + /* set the CH1NEN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->outputnstate) << 4U); + /* reset the CH1NP bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1NP); + /* set the CH1NP bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocnpolarity) << 4U); + /* reset the ISO1 bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO1); + /* set the ISO1 bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocidlestate) << 2U); + /* reset the ISO1N bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO1N); + /* set the ISO1N bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocnidlestate) << 2U); + } + TIMER_CHCTL0(timer_periph) &= ~(uint32_t)TIMER_CHCTL0_CH1MS; + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + /* reset the CH2EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2EN); + /* set the CH2EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->outputstate) << 8U); + /* reset the CH2P bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2P); + /* set the CH2P bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocpolarity) << 8U); + + if (TIMER0 == timer_periph) { + /* reset the CH2NEN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2NEN); + /* set the CH2NEN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->outputnstate) << 8U); + /* reset the CH2NP bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2NP); + /* set the CH2NP bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocnpolarity) << 8U); + /* reset the ISO2 bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO2); + /* set the ISO2 bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocidlestate) << 4U); + /* reset the ISO2N bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO2N); + /* set the ISO2N bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocnidlestate) << 4U); + } + TIMER_CHCTL1(timer_periph) &= ~(uint32_t)TIMER_CHCTL1_CH2MS; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + /* reset the CH3EN bit */ + TIMER_CHCTL2(timer_periph) &=(~(uint32_t)TIMER_CHCTL2_CH3EN); + /* set the CH3EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->outputstate) << 12U); + /* reset the CH3P bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH3P); + /* set the CH3P bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocpolarity) << 12U); + + if (TIMER0 == timer_periph) { + /* reset the ISO3 bit */ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_ISO3); + /* set the ISO3 bit */ + TIMER_CTL1(timer_periph) |= (uint32_t)((uint32_t)(ocpara->ocidlestate) << 6U); + } + TIMER_CHCTL1(timer_periph) &= ~(uint32_t)TIMER_CHCTL1_CH3MS; + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel output compare mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] ocmode: channel output compare mode + only one parameter can be selected which is shown as below: + \arg TIMER_OC_MODE_TIMING: timing mode + \arg TIMER_OC_MODE_ACTIVE: active mode + \arg TIMER_OC_MODE_INACTIVE: inactive mode + \arg TIMER_OC_MODE_TOGGLE: toggle mode + \arg TIMER_OC_MODE_LOW: force low mode + \arg TIMER_OC_MODE_HIGH: force high mode + \arg TIMER_OC_MODE_PWM0: PWM mode 0 + \arg TIMER_OC_MODE_PWM1: PWM mode 1 + \param[out] none + \retval none +*/ +void timer_channel_output_mode_config(uint32_t timer_periph, uint16_t channel, uint16_t ocmode) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0COMCTL); + TIMER_CHCTL0(timer_periph) |= (uint32_t)ocmode; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1COMCTL); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(ocmode) << 8U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2COMCTL); + TIMER_CHCTL1(timer_periph) |= (uint32_t)ocmode; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3COMCTL); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)(ocmode) << 8U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel output pulse value + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] pulse: channel output pulse value + \param[out] none + \retval none +*/ +void timer_channel_output_pulse_value_config(uint32_t timer_periph, uint16_t channel, uint32_t pulse) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CH0CV(timer_periph) = (uint32_t)pulse; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CH1CV(timer_periph) = (uint32_t)pulse; + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CH2CV(timer_periph) = (uint32_t)pulse; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CH3CV(timer_periph) = (uint32_t)pulse; + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel output shadow function + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] ocshadow: channel output shadow state + only one parameter can be selected which is shown as below: + \arg TIMER_OC_SHADOW_ENABLE: channel output shadow state enable + \arg TIMER_OC_SHADOW_DISABLE: channel output shadow state disable + \param[out] none + \retval none +*/ +void timer_channel_output_shadow_config(uint32_t timer_periph, uint16_t channel, uint16_t ocshadow) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0COMSEN); + TIMER_CHCTL0(timer_periph) |= (uint32_t)ocshadow; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1COMSEN); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(ocshadow) << 8U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2COMSEN); + TIMER_CHCTL1(timer_periph) |= (uint32_t)ocshadow; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3COMSEN); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)(ocshadow) << 8U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel output fast function + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] ocfast: channel output fast function + only one parameter can be selected which is shown as below: + \arg TIMER_OC_FAST_ENABLE: channel output fast function enable + \arg TIMER_OC_FAST_DISABLE: channel output fast function disable + \param[out] none + \retval none +*/ +void timer_channel_output_fast_config(uint32_t timer_periph, uint16_t channel, uint16_t ocfast) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0COMFEN); + TIMER_CHCTL0(timer_periph) |= (uint32_t)ocfast; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1COMFEN); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)ocfast << 8U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2COMFEN); + TIMER_CHCTL1(timer_periph) |= (uint32_t)ocfast; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3COMFEN); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)ocfast << 8U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel output clear function + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..41)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] occlear: channel output clear function + only one parameter can be selected which is shown as below: + \arg TIMER_OC_CLEAR_ENABLE: channel output clear function enable + \arg TIMER_OC_CLEAR_DISABLE: channel output clear function disable + \param[out] none + \retval none +*/ +void timer_channel_output_clear_config(uint32_t timer_periph, uint16_t channel, uint16_t occlear) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0COMCEN); + TIMER_CHCTL0(timer_periph) |= (uint32_t)occlear; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1COMCEN); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)occlear << 8U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2COMCEN); + TIMER_CHCTL1(timer_periph) |= (uint32_t)occlear; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3COMCEN); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)occlear << 8U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel output polarity + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] ocpolarity: channel output polarity + only one parameter can be selected which is shown as below: + \arg TIMER_OC_POLARITY_HIGH: channel output polarity is high + \arg TIMER_OC_POLARITY_LOW: channel output polarity is low + \param[out] none + \retval none +*/ +void timer_channel_output_polarity_config(uint32_t timer_periph, uint16_t channel, uint16_t ocpolarity) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0P); + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocpolarity; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1P); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocpolarity << 4U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2P); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocpolarity << 8U); + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH3P); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocpolarity << 12U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel complementary output polarity + \param[in] timer_periph: TIMERx(x=0) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0)) + \param[in] ocnpolarity: channel complementary output polarity + only one parameter can be selected which is shown as below: + \arg TIMER_OCN_POLARITY_HIGH: channel complementary output polarity is high + \arg TIMER_OCN_POLARITY_LOW: channel complementary output polarity is low + \param[out] none + \retval none +*/ +void timer_channel_complementary_output_polarity_config(uint32_t timer_periph, uint16_t channel, uint16_t ocnpolarity) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0NP); + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocnpolarity; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1NP); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocnpolarity << 4U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2NP); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocnpolarity << 8U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel enable state + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] state: TIMER channel enable state + only one parameter can be selected which is shown as below: + \arg TIMER_CCX_ENABLE: channel enable + \arg TIMER_CCX_DISABLE: channel disable + \param[out] none + \retval none +*/ +void timer_channel_output_state_config(uint32_t timer_periph, uint16_t channel, uint32_t state) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0EN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)state; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1EN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)state << 4U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2EN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)state << 8U); + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH3EN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)state << 12U); + break; + default: + break; + } +} + +/*! + \brief configure TIMER channel complementary output enable state + \param[in] timer_periph: TIMERx(x=0) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0 + \arg TIMER_CH_1: TIMER channel 1 + \arg TIMER_CH_2: TIMER channel 2 + \param[in] ocnstate: TIMER channel complementary output enable state + only one parameter can be selected which is shown as below: + \arg TIMER_CCXN_ENABLE: channel complementary enable + \arg TIMER_CCXN_DISABLE: channel complementary disable + \param[out] none + \retval none +*/ +void timer_channel_complementary_output_state_config(uint32_t timer_periph, uint16_t channel, uint16_t ocnstate) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0NEN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)ocnstate; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1NEN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocnstate << 4U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2NEN); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)ocnstate << 8U); + break; + default: + break; + } +} + +/*! + \brief initialize TIMER channel input parameter struct with a default value + \param[in] icpara: TIMER channel intput parameter struct + \param[out] none + \retval none +*/ +void timer_channel_input_struct_para_init(timer_ic_parameter_struct* icpara) +{ + /* initialize the channel input parameter struct member with the default value */ + icpara->icpolarity = TIMER_IC_POLARITY_RISING; + icpara->icselection = TIMER_IC_SELECTION_DIRECTTI; + icpara->icprescaler = TIMER_IC_PSC_DIV1; + icpara->icfilter = 0U; +} + +/*! + \brief configure TIMER input capture parameter + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] icpara: TIMER channel intput parameter struct + icpolarity: TIMER_IC_POLARITY_RISING, TIMER_IC_POLARITY_FALLING, + TIMER_IC_POLARITY_BOTH_EDGE(only for TIMER1~TIMER8) + icselection: TIMER_IC_SELECTION_DIRECTTI, TIMER_IC_SELECTION_INDIRECTTI, + TIMER_IC_SELECTION_ITS + icprescaler: TIMER_IC_PSC_DIV1, TIMER_IC_PSC_DIV2, TIMER_IC_PSC_DIV4, + TIMER_IC_PSC_DIV8 + icfilter: 0~15 + \param[out] none + \retval none +*/ +void timer_input_capture_config(uint32_t timer_periph, uint16_t channel, timer_ic_parameter_struct* icpara) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + /* reset the CH0EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0EN); + + /* reset the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH0P | TIMER_CHCTL2_CH0NP)); + TIMER_CHCTL2(timer_periph) |= (uint32_t)(icpara->icpolarity); + /* reset the CH0MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0MS); + TIMER_CHCTL0(timer_periph) |= (uint32_t)(icpara->icselection); + /* reset the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0CAPFLT); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(icpara->icfilter) << 4U); + + /* set the CH0EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH0EN; + break; + + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + /* reset the CH1EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1EN); + + /* reset the CH1P and CH1NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH1P | TIMER_CHCTL2_CH1NP)); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(icpara->icpolarity) << 4U); + /* reset the CH1MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1MS); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(icpara->icselection) << 8U); + /* reset the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1CAPFLT); + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(icpara->icfilter) << 12U); + + /* set the CH1EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH1EN; + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + /* reset the CH2EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH2EN); + + /* reset the CH2P and CH2NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH2P | TIMER_CHCTL2_CH2NP)); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(icpara->icpolarity) << 8U); + + /* reset the CH2MS bit */ + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2MS); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)(icpara->icselection)); + + /* reset the CH2CAPFLT bit */ + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2CAPFLT); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)(icpara->icfilter) << 4U); + + /* set the CH2EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH2EN; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + /* reset the CH3EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH3EN); + + /* reset the CH3P bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH3P)); + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(icpara->icpolarity) << 12U); + + /* reset the CH3MS bit */ + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3MS); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)(icpara->icselection) << 8U); + + /* reset the CH3CAPFLT bit */ + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3CAPFLT); + TIMER_CHCTL1(timer_periph) |= (uint32_t)((uint32_t)(icpara->icfilter) << 12U); + + /* set the CH3EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH3EN; + break; + default: + break; + } + /* configure TIMER channel input capture prescaler value */ + timer_channel_input_capture_prescaler_config(timer_periph, channel, (uint16_t)(icpara->icprescaler)); +} + +/*! + \brief configure TIMER channel input capture prescaler value + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[in] prescaler: channel input capture prescaler value + only one parameter can be selected which is shown as below: + \arg TIMER_IC_PSC_DIV1: no prescaler + \arg TIMER_IC_PSC_DIV2: divided by 2 + \arg TIMER_IC_PSC_DIV4: divided by 4 + \arg TIMER_IC_PSC_DIV8: divided by 8 + \param[out] none + \retval none +*/ +void timer_channel_input_capture_prescaler_config(uint32_t timer_periph, uint16_t channel, uint16_t prescaler) +{ + switch(channel){ + /* configure TIMER_CH_0 */ + case TIMER_CH_0: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0CAPPSC); + TIMER_CHCTL0(timer_periph) |= (uint32_t)prescaler; + break; + /* configure TIMER_CH_1 */ + case TIMER_CH_1: + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1CAPPSC); + TIMER_CHCTL0(timer_periph) |= ((uint32_t)prescaler << 8U); + break; + /* configure TIMER_CH_2 */ + case TIMER_CH_2: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH2CAPPSC); + TIMER_CHCTL1(timer_periph) |= (uint32_t)prescaler; + break; + /* configure TIMER_CH_3 */ + case TIMER_CH_3: + TIMER_CHCTL1(timer_periph) &= (~(uint32_t)TIMER_CHCTL1_CH3CAPPSC); + TIMER_CHCTL1(timer_periph) |= ((uint32_t)prescaler << 8U); + break; + default: + break; + } +} + +/*! + \brief read TIMER channel capture compare register value + \param[in] timer_periph: please refer to the following parameters + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0(TIMERx(x=0..4)) + \arg TIMER_CH_1: TIMER channel 1(TIMERx(x=0..4)) + \arg TIMER_CH_2: TIMER channel 2(TIMERx(x=0..4)) + \arg TIMER_CH_3: TIMER channel 3(TIMERx(x=0..4)) + \param[out] none + \retval channel capture compare register value +*/ +uint32_t timer_channel_capture_value_register_read(uint32_t timer_periph, uint16_t channel) +{ + uint32_t count_value = 0U; + + switch(channel){ + case TIMER_CH_0: + /* read TIMER channel 0 capture compare register value */ + count_value = TIMER_CH0CV(timer_periph); + break; + case TIMER_CH_1: + /* read TIMER channel 1 capture compare register value */ + count_value = TIMER_CH1CV(timer_periph); + break; + case TIMER_CH_2: + /* read TIMER channel 2 capture compare register value */ + count_value = TIMER_CH2CV(timer_periph); + break; + case TIMER_CH_3: + /* read TIMER channel 3 capture compare register value */ + count_value = TIMER_CH3CV(timer_periph); + break; + default: + break; + } + return (count_value); +} + +/*! + \brief configure TIMER input pwm capture function + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] channel: + only one parameter can be selected which is shown as below: + \arg TIMER_CH_0: TIMER channel 0 + \arg TIMER_CH_1: TIMER channel 1 + \param[in] icpwm: TIMER channel intput pwm parameter struct + icpolarity: TIMER_IC_POLARITY_RISING, TIMER_IC_POLARITY_FALLING + icselection: TIMER_IC_SELECTION_DIRECTTI, TIMER_IC_SELECTION_INDIRECTTI + icprescaler: TIMER_IC_PSC_DIV1, TIMER_IC_PSC_DIV2, TIMER_IC_PSC_DIV4, + TIMER_IC_PSC_DIV8 + icfilter: 0~15 + \param[out] none + \retval none +*/ +void timer_input_pwm_capture_config(uint32_t timer_periph, uint16_t channel, timer_ic_parameter_struct* icpwm) +{ + uint16_t icpolarity = 0x0U; + uint16_t icselection = 0x0U; + + /* Set channel input polarity */ + if(TIMER_IC_POLARITY_RISING == icpwm->icpolarity){ + icpolarity = TIMER_IC_POLARITY_FALLING; + }else{ + icpolarity = TIMER_IC_POLARITY_RISING; + } + /* Set channel input mode selection */ + if(TIMER_IC_SELECTION_DIRECTTI == icpwm->icselection){ + icselection = TIMER_IC_SELECTION_INDIRECTTI; + }else{ + icselection = TIMER_IC_SELECTION_DIRECTTI; + } + + if(TIMER_CH_0 == channel){ + /* reset the CH0EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0EN); + /* reset the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH0P | TIMER_CHCTL2_CH0NP)); + /* set the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)(icpwm->icpolarity); + /* reset the CH0MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0MS); + /* set the CH0MS bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)(icpwm->icselection); + /* reset the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0CAPFLT); + /* set the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) |= ((uint32_t)(icpwm->icfilter) << 4U); + /* set the CH0EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH0EN; + /* configure TIMER channel input capture prescaler value */ + timer_channel_input_capture_prescaler_config(timer_periph, TIMER_CH_0, (uint16_t)(icpwm->icprescaler)); + + /* reset the CH1EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1EN); + /* reset the CH1P and CH1NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH1P | TIMER_CHCTL2_CH1NP)); + /* set the CH1P and CH1NP bits */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)icpolarity<< 4U); + /* reset the CH1MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1MS); + /* set the CH1MS bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)icselection << 8U); + /* reset the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1CAPFLT); + /* set the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(icpwm->icfilter) << 12U); + /* set the CH1EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH1EN; + /* configure TIMER channel input capture prescaler value */ + timer_channel_input_capture_prescaler_config(timer_periph, TIMER_CH_1, (uint16_t)(icpwm->icprescaler)); + }else{ + /* reset the CH1EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1EN); + /* reset the CH1P and CH1NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH1P | TIMER_CHCTL2_CH1NP)); + /* set the CH1P and CH1NP bits */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)(icpwm->icpolarity) << 4U); + /* reset the CH1MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1MS); + /* set the CH1MS bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(icpwm->icselection) << 8U); + /* reset the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1CAPFLT); + /* set the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)(icpwm->icfilter) << 12U); + /* set the CH1EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH1EN; + /* configure TIMER channel input capture prescaler value */ + timer_channel_input_capture_prescaler_config(timer_periph, TIMER_CH_1, (uint16_t)(icpwm->icprescaler)); + + /* reset the CH0EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0EN); + /* reset the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH0P | TIMER_CHCTL2_CH0NP)); + /* set the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)icpolarity; + /* reset the CH0MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0MS); + /* set the CH0MS bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)icselection; + /* reset the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0CAPFLT); + /* set the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) |= ((uint32_t)(icpwm->icfilter) << 4U); + /* set the CH0EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH0EN; + /* configure TIMER channel input capture prescaler value */ + timer_channel_input_capture_prescaler_config(timer_periph, TIMER_CH_0, (uint16_t)(icpwm->icprescaler)); + } +} + +/*! + \brief configure TIMER hall sensor mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] hallmode: + only one parameter can be selected which is shown as below: + \arg TIMER_HALLINTERFACE_ENABLE: TIMER hall sensor mode enable + \arg TIMER_HALLINTERFACE_DISABLE: TIMER hall sensor mode disable + \param[out] none + \retval none +*/ +void timer_hall_mode_config(uint32_t timer_periph, uint32_t hallmode) +{ + if(TIMER_HALLINTERFACE_ENABLE == hallmode){ + TIMER_CTL1(timer_periph) |= (uint32_t)TIMER_CTL1_TI0S; + }else if(TIMER_HALLINTERFACE_DISABLE == hallmode){ + TIMER_CTL1(timer_periph) &= ~(uint32_t)TIMER_CTL1_TI0S; + }else{ + /* illegal parameters */ + } +} + +/*! + \brief select TIMER input trigger source + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] intrigger: + only one parameter can be selected which is shown as below: + \arg TIMER_SMCFG_TRGSEL_ITI0: internal trigger 0(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_ITI1: internal trigger 1(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_ITI2: internal trigger 2(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_ITI3: internal trigger 3(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_CI0F_ED: TI0 edge detector(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_CI0FE0: filtered TIMER input 0(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_CI1FE1: filtered TIMER input 1(TIMERx(x=0..4)) + \arg TIMER_SMCFG_TRGSEL_ETIFP: filtered external trigger input(TIMERx(x=0..4)) + \param[out] none + \retval none +*/ +void timer_input_trigger_source_select(uint32_t timer_periph, uint32_t intrigger) +{ + TIMER_SMCFG(timer_periph) &= (~(uint32_t)TIMER_SMCFG_TRGS); + TIMER_SMCFG(timer_periph) |= (uint32_t)intrigger; +} + +/*! + \brief select TIMER master mode output trigger source + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] outrigger: + only one parameter can be selected which is shown as below: + \arg TIMER_TRI_OUT_SRC_RESET: the UPG bit as trigger output(TIMERx(x=0..6)) + \arg TIMER_TRI_OUT_SRC_ENABLE: the counter enable signal TIMER_CTL0_CEN as trigger output(TIMERx(x=0..6)) + \arg TIMER_TRI_OUT_SRC_UPDATE: update event as trigger output(TIMERx(x=0..6)) + \arg TIMER_TRI_OUT_SRC_CH0: a capture or a compare match occurred in channel 0 as trigger output TRGO(TIMERx(x=0..4)) + \arg TIMER_TRI_OUT_SRC_O0CPRE: O0CPRE as trigger output(TIMERx(x=0..4)) + \arg TIMER_TRI_OUT_SRC_O1CPRE: O1CPRE as trigger output(TIMERx(x=0..4)) + \arg TIMER_TRI_OUT_SRC_O2CPRE: O2CPRE as trigger output(TIMERx(x=0..4)) + \arg TIMER_TRI_OUT_SRC_O3CPRE: O3CPRE as trigger output(TIMERx(x=0..4)) + \param[out] none + \retval none +*/ +void timer_master_output_trigger_source_select(uint32_t timer_periph, uint32_t outrigger) +{ + TIMER_CTL1(timer_periph) &= (~(uint32_t)TIMER_CTL1_MMC); + TIMER_CTL1(timer_periph) |= (uint32_t)outrigger; +} + +/*! + \brief select TIMER slave mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] slavemode: + only one parameter can be selected which is shown as below: + \arg TIMER_SLAVE_MODE_DISABLE: slave mode disable + \arg TIMER_ENCODER_MODE0: encoder mode 0 + \arg TIMER_ENCODER_MODE1: encoder mode 1 + \arg TIMER_ENCODER_MODE2: encoder mode 2 + \arg TIMER_SLAVE_MODE_RESTART: restart mode + \arg TIMER_SLAVE_MODE_PAUSE: pause mode + \arg TIMER_SLAVE_MODE_EVENT: event mode + \arg TIMER_SLAVE_MODE_EXTERNAL0: external clock mode 0 + \param[out] none + \retval none +*/ + +void timer_slave_mode_select(uint32_t timer_periph, uint32_t slavemode) +{ + TIMER_SMCFG(timer_periph) &= (~(uint32_t)TIMER_SMCFG_SMC); + TIMER_SMCFG(timer_periph) |= (uint32_t)slavemode; +} + +/*! + \brief configure TIMER master slave mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] masterslave: + only one parameter can be selected which is shown as below: + \arg TIMER_MASTER_SLAVE_MODE_ENABLE: master slave mode enable + \arg TIMER_MASTER_SLAVE_MODE_DISABLE: master slave mode disable + \param[out] none + \retval none +*/ +void timer_master_slave_mode_config(uint32_t timer_periph, uint32_t masterslave) +{ + if(TIMER_MASTER_SLAVE_MODE_ENABLE == masterslave){ + TIMER_SMCFG(timer_periph) |= (uint32_t)TIMER_SMCFG_MSM; + }else if(TIMER_MASTER_SLAVE_MODE_DISABLE == masterslave){ + TIMER_SMCFG(timer_periph) &= ~(uint32_t)TIMER_SMCFG_MSM; + }else{ + /* illegal parameters */ + } +} + +/*! + \brief configure TIMER external trigger input + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] extprescaler: + only one parameter can be selected which is shown as below: + \arg TIMER_EXT_TRI_PSC_OFF: no divided + \arg TIMER_EXT_TRI_PSC_DIV2: divided by 2 + \arg TIMER_EXT_TRI_PSC_DIV4: divided by 4 + \arg TIMER_EXT_TRI_PSC_DIV8: divided by 8 + \param[in] extpolarity: + only one parameter can be selected which is shown as below: + \arg TIMER_ETP_FALLING: active low or falling edge active + \arg TIMER_ETP_RISING: active high or rising edge active + \param[in] extfilter: a value between 0 and 15 + \param[out] none + \retval none +*/ +void timer_external_trigger_config(uint32_t timer_periph, uint32_t extprescaler, uint32_t extpolarity, uint32_t extfilter) +{ + TIMER_SMCFG(timer_periph) &= (~(uint32_t)(TIMER_SMCFG_ETP | TIMER_SMCFG_ETPSC | TIMER_SMCFG_ETFC)); + TIMER_SMCFG(timer_periph) |= (uint32_t)(extprescaler | extpolarity); + TIMER_SMCFG(timer_periph) |= (uint32_t)(extfilter << 8U); +} + +/*! + \brief configure TIMER quadrature decoder mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] decomode: + only one parameter can be selected which is shown as below: + \arg TIMER_ENCODER_MODE0: counter counts on CI0FE0 edge depending on CI1FE1 level + \arg TIMER_ENCODER_MODE1: counter counts on CI1FE1 edge depending on CI0FE0 level + \arg TIMER_ENCODER_MODE2: counter counts on both CI0FE0 and CI1FE1 edges depending on the level of the other input + \param[in] ic0polarity: + only one parameter can be selected which is shown as below: + \arg TIMER_IC_POLARITY_RISING: capture rising edge + \arg TIMER_IC_POLARITY_FALLING: capture falling edge + \param[in] ic1polarity: + only one parameter can be selected which is shown as below: + \arg TIMER_IC_POLARITY_RISING: capture rising edge + \arg TIMER_IC_POLARITY_FALLING: capture falling edge + \param[out] none + \retval none +*/ +void timer_quadrature_decoder_mode_config(uint32_t timer_periph, uint32_t decomode, uint16_t ic0polarity, uint16_t ic1polarity) +{ + /* configure the quadrature decoder mode */ + TIMER_SMCFG(timer_periph) &= (~(uint32_t)TIMER_SMCFG_SMC); + TIMER_SMCFG(timer_periph) |= (uint32_t)decomode; + /* configure input capture selection */ + TIMER_CHCTL0(timer_periph) &= (uint32_t)(((~(uint32_t)TIMER_CHCTL0_CH0MS)) & ((~(uint32_t)TIMER_CHCTL0_CH1MS))); + TIMER_CHCTL0(timer_periph) |= (uint32_t)(TIMER_IC_SELECTION_DIRECTTI | ((uint32_t)TIMER_IC_SELECTION_DIRECTTI << 8U)); + /* configure channel input capture polarity */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH0P | TIMER_CHCTL2_CH0NP)); + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH1P | TIMER_CHCTL2_CH1NP)); + TIMER_CHCTL2(timer_periph) |= ((uint32_t)ic0polarity | ((uint32_t)ic1polarity << 4U)); +} + +/*! + \brief configure TIMER internal clock mode + \param[in] timer_periph: TIMERx(x=0..4) + \param[out] none + \retval none +*/ +void timer_internal_clock_config(uint32_t timer_periph) +{ + TIMER_SMCFG(timer_periph) &= ~(uint32_t)TIMER_SMCFG_SMC; +} + +/*! + \brief configure TIMER the internal trigger as external clock input + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] intrigger: + only one parameter can be selected which is shown as below: + \arg TIMER_SMCFG_TRGSEL_ITI0: internal trigger 0 + \arg TIMER_SMCFG_TRGSEL_ITI1: internal trigger 1 + \arg TIMER_SMCFG_TRGSEL_ITI2: internal trigger 2 + \arg TIMER_SMCFG_TRGSEL_ITI3: internal trigger 3 + \param[out] none + \retval none +*/ +void timer_internal_trigger_as_external_clock_config(uint32_t timer_periph, uint32_t intrigger) +{ + timer_input_trigger_source_select(timer_periph, intrigger); + TIMER_SMCFG(timer_periph) &= ~(uint32_t)TIMER_SMCFG_SMC; + TIMER_SMCFG(timer_periph) |= (uint32_t)TIMER_SLAVE_MODE_EXTERNAL0; +} + +/*! + \brief configure TIMER the external trigger as external clock input + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] extrigger: + only one parameter can be selected which is shown as below: + \arg TIMER_SMCFG_TRGSEL_CI0F_ED: TI0 edge detector + \arg TIMER_SMCFG_TRGSEL_CI0FE0: filtered TIMER input 0 + \arg TIMER_SMCFG_TRGSEL_CI1FE1: filtered TIMER input 1 + \param[in] extpolarity: + only one parameter can be selected which is shown as below: + \arg TIMER_IC_POLARITY_RISING: active low or falling edge active + \arg TIMER_IC_POLARITY_FALLING: active high or rising edge active + \param[in] extfilter: a value between 0 and 15 + \param[out] none + \retval none +*/ +void timer_external_trigger_as_external_clock_config(uint32_t timer_periph, uint32_t extrigger, uint16_t extpolarity, uint32_t extfilter) +{ + if(TIMER_SMCFG_TRGSEL_CI1FE1 == extrigger){ + /* reset the CH1EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH1EN); + /* reset the CH1NP bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH1P | TIMER_CHCTL2_CH1NP)); + /* set the CH1NP bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)((uint32_t)extpolarity << 4U); + /* reset the CH1MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1MS); + /* set the CH1MS bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)((uint32_t)TIMER_IC_SELECTION_DIRECTTI << 8U); + /* reset the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH1CAPFLT); + /* set the CH1CAPFLT bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)(extfilter << 12U); + /* set the CH1EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH1EN; + }else{ + /* reset the CH0EN bit */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)TIMER_CHCTL2_CH0EN); + /* reset the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) &= (~(uint32_t)(TIMER_CHCTL2_CH0P | TIMER_CHCTL2_CH0NP)); + /* set the CH0P and CH0NP bits */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)extpolarity; + /* reset the CH0MS bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0MS); + /* set the CH0MS bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)TIMER_IC_SELECTION_DIRECTTI; + /* reset the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) &= (~(uint32_t)TIMER_CHCTL0_CH0CAPFLT); + /* reset the CH0CAPFLT bit */ + TIMER_CHCTL0(timer_periph) |= (uint32_t)(extfilter << 4U); + /* set the CH0EN bit */ + TIMER_CHCTL2(timer_periph) |= (uint32_t)TIMER_CHCTL2_CH0EN; + } + /* select TIMER input trigger source */ + timer_input_trigger_source_select(timer_periph, extrigger); + /* reset the SMC bit */ + TIMER_SMCFG(timer_periph) &= (~(uint32_t)TIMER_SMCFG_SMC); + /* set the SMC bit */ + TIMER_SMCFG(timer_periph) |= (uint32_t)TIMER_SLAVE_MODE_EXTERNAL0; +} + +/*! + \brief configure TIMER the external clock mode0 + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] extprescaler: + only one parameter can be selected which is shown as below: + \arg TIMER_EXT_TRI_PSC_OFF: no divided + \arg TIMER_EXT_TRI_PSC_DIV2: divided by 2 + \arg TIMER_EXT_TRI_PSC_DIV4: divided by 4 + \arg TIMER_EXT_TRI_PSC_DIV8: divided by 8 + \param[in] extpolarity: + only one parameter can be selected which is shown as below: + \arg TIMER_ETP_FALLING: active low or falling edge active + \arg TIMER_ETP_RISING: active high or rising edge active + \param[in] extfilter: a value between 0 and 15 + \param[out] none + \retval none +*/ +void timer_external_clock_mode0_config(uint32_t timer_periph, uint32_t extprescaler, uint32_t extpolarity, uint32_t extfilter) +{ + /* configure TIMER external trigger input */ + timer_external_trigger_config(timer_periph, extprescaler, extpolarity, extfilter); + /* reset the SMC bit,TRGS bit */ + TIMER_SMCFG(timer_periph) &= (~(uint32_t)(TIMER_SMCFG_SMC | TIMER_SMCFG_TRGS)); + /* set the SMC bit,TRGS bit */ + TIMER_SMCFG(timer_periph) |= (uint32_t)(TIMER_SLAVE_MODE_EXTERNAL0 | TIMER_SMCFG_TRGSEL_ETIFP); +} + +/*! + \brief configure TIMER the external clock mode1 + \param[in] timer_periph: TIMERx(x=0..4) + \param[in] extprescaler: + only one parameter can be selected which is shown as below: + \arg TIMER_EXT_TRI_PSC_OFF: no divided + \arg TIMER_EXT_TRI_PSC_DIV2: divided by 2 + \arg TIMER_EXT_TRI_PSC_DIV4: divided by 4 + \arg TIMER_EXT_TRI_PSC_DIV8: divided by 8 + \param[in] extpolarity: + only one parameter can be selected which is shown as below: + \arg TIMER_ETP_FALLING: active low or falling edge active + \arg TIMER_ETP_RISING: active high or rising edge active + \param[in] extfilter: a value between 0 and 15 + \param[out] none + \retval none +*/ +void timer_external_clock_mode1_config(uint32_t timer_periph, uint32_t extprescaler, uint32_t extpolarity, uint32_t extfilter) +{ + /* configure TIMER external trigger input */ + timer_external_trigger_config(timer_periph, extprescaler, extpolarity, extfilter); + TIMER_SMCFG(timer_periph) |= (uint32_t)TIMER_SMCFG_SMC1; +} + +/*! + \brief disable TIMER the external clock mode1 + \param[in] timer_periph: TIMERx(x=0..4) + \param[out] none + \retval none +*/ +void timer_external_clock_mode1_disable(uint32_t timer_periph) +{ + TIMER_SMCFG(timer_periph) &= ~(uint32_t)TIMER_SMCFG_SMC1; +} + +/*! + \brief enable the TIMER interrupt + \param[in] timer_periph: please refer to the following parameters + \param[in] interrupt: specify which interrupt to enable + one or more parameters can be selected which are shown as below: + \arg TIMER_INT_UP: update interrupt enable, TIMERx(x=0..6) + \arg TIMER_INT_CH0: channel 0 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CH1: channel 1 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CH2: channel 2 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CH3: channel 3 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CMT: commutation interrupt enable, TIMERx(x=0) + \arg TIMER_INT_TRG: trigger interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_BRK: break interrupt enable, TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_interrupt_enable(uint32_t timer_periph, uint32_t interrupt) +{ + TIMER_DMAINTEN(timer_periph) |= (uint32_t) interrupt; +} + +/*! + \brief disable the TIMER interrupt + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] interrupt: specify which interrupt to disbale + one or more parameters can be selected which are shown as below: + \arg TIMER_INT_UP: update interrupt enable, TIMERx(x=0..6) + \arg TIMER_INT_CH0: channel 0 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CH1: channel 1 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CH2: channel 2 interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_CH3: channel 3 interrupt enable , TIMERx(x=0..4) + \arg TIMER_INT_CMT: commutation interrupt enable, TIMERx(x=0) + \arg TIMER_INT_TRG: trigger interrupt enable, TIMERx(x=0..4) + \arg TIMER_INT_BRK: break interrupt enable, TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_interrupt_disable(uint32_t timer_periph, uint32_t interrupt) +{ + TIMER_DMAINTEN(timer_periph) &= (~(uint32_t)interrupt); +} + +/*! + \brief get timer interrupt flag + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] interrupt: the timer interrupt bits + only one parameter can be selected which is shown as below: + \arg TIMER_INT_FLAG_UP: update interrupt flag, TIMERx(x=0..6) + \arg TIMER_INT_FLAG_CH0: channel 0 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CH1: channel 1 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CH2: channel 2 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CH3: channel 3 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CMT: channel commutation interrupt flag, TIMERx(x=0) + \arg TIMER_INT_FLAG_TRG: trigger interrupt flag, TIMERx(x=0) + \arg TIMER_INT_FLAG_BRK: break interrupt flag, TIMERx(x=0) + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus timer_interrupt_flag_get(uint32_t timer_periph, uint32_t interrupt) +{ + uint32_t val; + val = (TIMER_DMAINTEN(timer_periph) & interrupt); + if((RESET != (TIMER_INTF(timer_periph) & interrupt)) && (RESET != val)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear TIMER interrupt flag + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] interrupt: the timer interrupt bits + one or more parameters can be selected which are shown as below: + \arg TIMER_INT_FLAG_UP: update interrupt flag, TIMERx(x=0..6) + \arg TIMER_INT_FLAG_CH0: channel 0 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CH1: channel 1 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CH2: channel 2 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CH3: channel 3 interrupt flag, TIMERx(x=0..4) + \arg TIMER_INT_FLAG_CMT: channel commutation interrupt flag, TIMERx(x=0) + \arg TIMER_INT_FLAG_TRG: trigger interrupt flag, TIMERx(x=0) + \arg TIMER_INT_FLAG_BRK: break interrupt flag, TIMERx(x=0) + \param[out] none + \retval none +*/ +void timer_interrupt_flag_clear(uint32_t timer_periph, uint32_t interrupt) +{ + TIMER_INTF(timer_periph) = (~(uint32_t)interrupt); +} + +/*! + \brief get TIMER flags + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] flag: the timer interrupt flags + only one parameter can be selected which is shown as below: + \arg TIMER_FLAG_UP: update flag, TIMERx(x=0..6) + \arg TIMER_FLAG_CH0: channel 0 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH1: channel 1 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH2: channel 2 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH3: channel 3 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CMT: channel commutation flag, TIMERx(x=0) + \arg TIMER_FLAG_TRG: trigger flag, TIMERx(x=0) + \arg TIMER_FLAG_BRK: break flag, TIMERx(x=0) + \arg TIMER_FLAG_CH0O: channel 0 overcapture flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH1O: channel 1 overcapture flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH2O: channel 2 overcapture flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH3O: channel 3 overcapture flag, TIMERx(x=0..4) + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus timer_flag_get(uint32_t timer_periph, uint32_t flag) +{ + if(RESET != (TIMER_INTF(timer_periph) & flag)){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear TIMER flags + \param[in] timer_periph: TIMERx(x=0..6) + \param[in] flag: the timer interrupt flags + one or more parameters can be selected which are shown as below: + \arg TIMER_FLAG_UP: update flag, TIMERx(x=0..6) + \arg TIMER_FLAG_CH0: channel 0 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH1: channel 1 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH2: channel 2 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH3: channel 3 flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CMT: channel commutation flag, TIMERx(x=0) + \arg TIMER_FLAG_TRG: trigger flag, TIMERx(x=0) + \arg TIMER_FLAG_BRK: break flag, TIMERx(x=0) + \arg TIMER_FLAG_CH0O: channel 0 overcapture flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH1O: channel 1 overcapture flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH2O: channel 2 overcapture flag, TIMERx(x=0..4) + \arg TIMER_FLAG_CH3O: channel 3 overcapture flag, TIMERx(x=0..4) + \param[out] none + \retval none +*/ +void timer_flag_clear(uint32_t timer_periph, uint32_t flag) +{ + TIMER_INTF(timer_periph) = (~(uint32_t)flag); +} + + diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_usart.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_usart.c new file mode 100644 index 00000000..63fc9b05 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_usart.c @@ -0,0 +1,781 @@ +/*! + \file gd32vf103_usart.c + \brief USART driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_usart.h" + +/*! + \brief reset USART/UART + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_deinit(uint32_t usart_periph) +{ + switch(usart_periph){ + case USART0: + /* reset USART0 */ + rcu_periph_reset_enable(RCU_USART0RST); + rcu_periph_reset_disable(RCU_USART0RST); + break; + case USART1: + /* reset USART1 */ + rcu_periph_reset_enable(RCU_USART1RST); + rcu_periph_reset_disable(RCU_USART1RST); + break; + case USART2: + /* reset USART2 */ + rcu_periph_reset_enable(RCU_USART2RST); + rcu_periph_reset_disable(RCU_USART2RST); + break; + case UART3: + /* reset UART3 */ + rcu_periph_reset_enable(RCU_UART3RST); + rcu_periph_reset_disable(RCU_UART3RST); + break; + case UART4: + /* reset UART4 */ + rcu_periph_reset_enable(RCU_UART4RST); + rcu_periph_reset_disable(RCU_UART4RST); + break; + default: + break; + } +} + +/*! + \brief configure USART baud rate value + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] baudval: baud rate value + \param[out] none + \retval none +*/ +void usart_baudrate_set(uint32_t usart_periph, uint32_t baudval) +{ + uint32_t uclk=0U, intdiv=0U, fradiv=0U, udiv=0U; + switch(usart_periph){ + /* get clock frequency */ + case USART0: + /* get USART0 clock */ + uclk=rcu_clock_freq_get(CK_APB2); + break; + case USART1: + /* get USART1 clock */ + uclk=rcu_clock_freq_get(CK_APB1); + break; + case USART2: + /* get USART2 clock */ + uclk=rcu_clock_freq_get(CK_APB1); + break; + case UART3: + /* get UART3 clock */ + uclk=rcu_clock_freq_get(CK_APB1); + break; + case UART4: + /* get UART4 clock */ + uclk=rcu_clock_freq_get(CK_APB1); + break; + default: + break; + } + /* oversampling by 16, configure the value of USART_BAUD */ + udiv = (uclk+baudval/2U)/baudval; + intdiv = udiv & (0x0000fff0U); + fradiv = udiv & (0x0000000fU); + USART_BAUD(usart_periph) = ((USART_BAUD_FRADIV | USART_BAUD_INTDIV) & (intdiv | fradiv)); +} + +/*! + \brief configure USART parity + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] paritycfg: configure USART parity + only one parameter can be selected which is shown as below: + \arg USART_PM_NONE: no parity + \arg USART_PM_ODD: odd parity + \arg USART_PM_EVEN: even parity + \param[out] none + \retval none +*/ +void usart_parity_config(uint32_t usart_periph, uint32_t paritycfg) +{ + /* clear USART_CTL0 PM,PCEN bits */ + USART_CTL0(usart_periph) &= ~(USART_CTL0_PM | USART_CTL0_PCEN); + /* configure USART parity mode */ + USART_CTL0(usart_periph) |= paritycfg ; +} + +/*! + \brief configure USART word length + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] wlen: USART word length configure + only one parameter can be selected which is shown as below: + \arg USART_WL_8BIT: 8 bits + \arg USART_WL_9BIT: 9 bits + \param[out] none + \retval none +*/ +void usart_word_length_set(uint32_t usart_periph, uint32_t wlen) +{ + /* clear USART_CTL0 WL bit */ + USART_CTL0(usart_periph) &= ~USART_CTL0_WL; + /* configure USART word length */ + USART_CTL0(usart_periph) |= wlen; +} + +/*! + \brief configure USART stop bit length + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] stblen: USART stop bit configure + only one parameter can be selected which is shown as below: + \arg USART_STB_1BIT: 1 bit + \arg USART_STB_0_5BIT: 0.5 bit, not available for UARTx(x=3,4) + \arg USART_STB_2BIT: 2 bits + \arg USART_STB_1_5BIT: 1.5 bits, not available for UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_stop_bit_set(uint32_t usart_periph, uint32_t stblen) +{ + /* clear USART_CTL1 STB bits */ + USART_CTL1(usart_periph) &= ~USART_CTL1_STB; + /* configure USART stop bits */ + USART_CTL1(usart_periph) |= stblen; +} + +/*! + \brief enable USART + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_enable(uint32_t usart_periph) +{ + USART_CTL0(usart_periph) |= USART_CTL0_UEN; +} + +/*! + \brief disable USART + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_disable(uint32_t usart_periph) +{ + USART_CTL0(usart_periph) &= ~(USART_CTL0_UEN); +} + +/*! + \brief configure USART transmitter + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] txconfig: enable or disable USART transmitter + only one parameter can be selected which is shown as below: + \arg USART_TRANSMIT_ENABLE: enable USART transmission + \arg USART_TRANSMIT_DISABLE: disable USART transmission + \param[out] none + \retval none +*/ +void usart_transmit_config(uint32_t usart_periph, uint32_t txconfig) +{ + uint32_t ctl = 0U; + + ctl = USART_CTL0(usart_periph); + ctl &= ~USART_CTL0_TEN; + ctl |= txconfig; + /* configure transfer mode */ + USART_CTL0(usart_periph) = ctl; +} + +/*! + \brief configure USART receiver + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] rxconfig: enable or disable USART receiver + only one parameter can be selected which is shown as below: + \arg USART_RECEIVE_ENABLE: enable USART reception + \arg USART_RECEIVE_DISABLE: disable USART reception + \param[out] none + \retval none +*/ +void usart_receive_config(uint32_t usart_periph, uint32_t rxconfig) +{ + uint32_t ctl = 0U; + + ctl = USART_CTL0(usart_periph); + ctl &= ~USART_CTL0_REN; + ctl |= rxconfig; + /* configure receiver mode */ + USART_CTL0(usart_periph) = ctl; +} + +/*! + \brief USART transmit data function + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] data: data of transmission + \param[out] none + \retval none +*/ +void usart_data_transmit(uint32_t usart_periph, uint32_t data) +{ + USART_DATA(usart_periph) = USART_DATA_DATA & data; +} + +/*! + \brief USART receive data function + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval data of received +*/ +uint16_t usart_data_receive(uint32_t usart_periph) +{ + return (uint16_t)(GET_BITS(USART_DATA(usart_periph), 0U, 8U)); +} + +/*! + \brief configure the address of the USART in wake up by address match mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] addr: address of USART/UART + \param[out] none + \retval none +*/ +void usart_address_config(uint32_t usart_periph, uint8_t addr) +{ + USART_CTL1(usart_periph) &= ~(USART_CTL1_ADDR); + USART_CTL1(usart_periph) |= (USART_CTL1_ADDR & addr); +} + +/*! + \brief receiver in mute mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_mute_mode_enable(uint32_t usart_periph) +{ + USART_CTL0(usart_periph) |= USART_CTL0_RWU; +} + +/*! + \brief receiver in active mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_mute_mode_disable(uint32_t usart_periph) +{ + USART_CTL0(usart_periph) &= ~(USART_CTL0_RWU); +} + +/*! + \brief configure wakeup method in mute mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] wmethod: two methods be used to enter or exit the mute mode + only one parameter can be selected which is shown as below: + \arg USART_WM_IDLE: idle line + \arg USART_WM_ADDR: address mask + \param[out] none + \retval none +*/ +void usart_mute_mode_wakeup_config(uint32_t usart_periph, uint32_t wmethod) +{ + USART_CTL0(usart_periph) &= ~(USART_CTL0_WM); + USART_CTL0(usart_periph) |= wmethod; +} + +/*! + \brief enable LIN mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_lin_mode_enable(uint32_t usart_periph) +{ + USART_CTL1(usart_periph) |= USART_CTL1_LMEN; +} + +/*! + \brief disable LIN mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_lin_mode_disable(uint32_t usart_periph) +{ + USART_CTL1(usart_periph) &= ~(USART_CTL1_LMEN); +} + +/*! + \brief configure lin break frame length + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] lblen: lin break frame length + only one parameter can be selected which is shown as below: + \arg USART_LBLEN_10B: 10 bits + \arg USART_LBLEN_11B: 11 bits + \param[out] none + \retval none +*/ +void usart_lin_break_detection_length_config(uint32_t usart_periph, uint32_t lblen) +{ + USART_CTL1(usart_periph) &= ~(USART_CTL1_LBLEN); + USART_CTL1(usart_periph) |= (USART_CTL1_LBLEN & lblen); +} + +/*! + \brief send break frame + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_send_break(uint32_t usart_periph) +{ + USART_CTL0(usart_periph) |= USART_CTL0_SBKCMD; +} + +/*! + \brief enable half duplex mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_halfduplex_enable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) |= USART_CTL2_HDEN; +} + +/*! + \brief disable half duplex mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_halfduplex_disable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) &= ~(USART_CTL2_HDEN); +} + +/*! + \brief enable CK pin in synchronous mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[out] none + \retval none +*/ +void usart_synchronous_clock_enable(uint32_t usart_periph) +{ + USART_CTL1(usart_periph) |= USART_CTL1_CKEN; +} + +/*! + \brief disable CK pin in synchronous mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[out] none + \retval none +*/ +void usart_synchronous_clock_disable(uint32_t usart_periph) +{ + USART_CTL1(usart_periph) &= ~(USART_CTL1_CKEN); +} + +/*! + \brief configure USART synchronous mode parameters + \param[in] usart_periph: USARTx(x=0,1,2) + \param[in] clen: CK length + only one parameter can be selected which is shown as below: + \arg USART_CLEN_NONE: there are 7 CK pulses for an 8 bit frame and 8 CK pulses for a 9 bit frame + \arg USART_CLEN_EN: there are 8 CK pulses for an 8 bit frame and 9 CK pulses for a 9 bit frame + \param[in] cph: clock phase + only one parameter can be selected which is shown as below: + \arg USART_CPH_1CK: first clock transition is the first data capture edge + \arg USART_CPH_2CK: second clock transition is the first data capture edge + \param[in] cpl: clock polarity + only one parameter can be selected which is shown as below: + \arg USART_CPL_LOW: steady low value on CK pin + \arg USART_CPL_HIGH: steady high value on CK pin + \param[out] none + \retval none +*/ +void usart_synchronous_clock_config(uint32_t usart_periph, uint32_t clen, uint32_t cph, uint32_t cpl) +{ + uint32_t ctl = 0U; + + /* read USART_CTL1 register */ + ctl = USART_CTL1(usart_periph); + ctl &= ~(USART_CTL1_CLEN | USART_CTL1_CPH | USART_CTL1_CPL); + /* set CK length, CK phase, CK polarity */ + ctl |= (USART_CTL1_CLEN & clen) | (USART_CTL1_CPH & cph) | (USART_CTL1_CPL & cpl); + + USART_CTL1(usart_periph) = ctl; +} + +/*! + \brief configure guard time value in smartcard mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[in] gaut: guard time value + \param[out] none + \retval none +*/ +void usart_guard_time_config(uint32_t usart_periph,uint32_t gaut) +{ + USART_GP(usart_periph) &= ~(USART_GP_GUAT); + USART_GP(usart_periph) |= (USART_GP_GUAT & ((gaut)<<8)); +} + +/*! + \brief enable smartcard mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[out] none + \retval none +*/ +void usart_smartcard_mode_enable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) |= USART_CTL2_SCEN; +} + +/*! + \brief disable smartcard mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[out] none + \retval none +*/ +void usart_smartcard_mode_disable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) &= ~(USART_CTL2_SCEN); +} + +/*! + \brief enable NACK in smartcard mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[out] none + \retval none +*/ +void usart_smartcard_mode_nack_enable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) |= USART_CTL2_NKEN; +} + +/*! + \brief disable NACK in smartcard mode + \param[in] usart_periph: USARTx(x=0,1,2) + \param[out] none + \retval none +*/ +void usart_smartcard_mode_nack_disable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) &= ~(USART_CTL2_NKEN); +} + +/*! + \brief enable IrDA mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_irda_mode_enable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) |= USART_CTL2_IREN; +} + +/*! + \brief disable IrDA mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[out] none + \retval none +*/ +void usart_irda_mode_disable(uint32_t usart_periph) +{ + USART_CTL2(usart_periph) &= ~(USART_CTL2_IREN); +} + +/*! + \brief configure the peripheral clock prescaler in USART IrDA low-power mode + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] psc: 0x00-0xFF + \param[out] none + \retval none +*/ +void usart_prescaler_config(uint32_t usart_periph, uint8_t psc) +{ + USART_GP(usart_periph) &= ~(USART_GP_PSC); + USART_GP(usart_periph) |= psc; +} + +/*! + \brief configure IrDA low-power + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] irlp: IrDA low-power or normal + only one parameter can be selected which is shown as below: + \arg USART_IRLP_LOW: low-power + \arg USART_IRLP_NORMAL: normal + \param[out] none + \retval none +*/ +void usart_irda_lowpower_config(uint32_t usart_periph, uint32_t irlp) +{ + USART_CTL2(usart_periph) &= ~(USART_CTL2_IRLP); + USART_CTL2(usart_periph) |= (USART_CTL2_IRLP & irlp); +} + +/*! + \brief configure hardware flow control RTS + \param[in] usart_periph: USARTx(x=0,1,2) + \param[in] rtsconfig: enable or disable RTS + only one parameter can be selected which is shown as below: + \arg USART_RTS_ENABLE: enable RTS + \arg USART_RTS_DISABLE: disable RTS + \param[out] none + \retval none +*/ +void usart_hardware_flow_rts_config(uint32_t usart_periph, uint32_t rtsconfig) +{ + uint32_t ctl = 0U; + + ctl = USART_CTL2(usart_periph); + ctl &= ~USART_CTL2_RTSEN; + ctl |= rtsconfig; + /* configure RTS */ + USART_CTL2(usart_periph) = ctl; +} + +/*! + \brief configure hardware flow control CTS + \param[in] usart_periph: USARTx(x=0,1,2) + \param[in] ctsconfig: enable or disable CTS + only one parameter can be selected which is shown as below: + \arg USART_CTS_ENABLE: enable CTS + \arg USART_CTS_DISABLE: disable CTS + \param[out] none + \retval none +*/ +void usart_hardware_flow_cts_config(uint32_t usart_periph, uint32_t ctsconfig) +{ + uint32_t ctl = 0U; + + ctl = USART_CTL2(usart_periph); + ctl &= ~USART_CTL2_CTSEN; + ctl |= ctsconfig; + /* configure CTS */ + USART_CTL2(usart_periph) = ctl; +} + +/*! + \brief configure USART DMA reception + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3) + \param[in] dmacmd: enable or disable DMA for reception + only one parameter can be selected which is shown as below: + \arg USART_DENR_ENABLE: DMA enable for reception + \arg USART_DENR_DISABLE: DMA disable for reception + \param[out] none + \retval none +*/ +void usart_dma_receive_config(uint32_t usart_periph, uint32_t dmacmd) +{ + uint32_t ctl = 0U; + + ctl = USART_CTL2(usart_periph); + ctl &= ~USART_CTL2_DENR; + ctl |= dmacmd; + /* configure DMA reception */ + USART_CTL2(usart_periph) = ctl; +} + +/*! + \brief configure USART DMA transmission + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3) + \param[in] dmacmd: enable or disable DMA for transmission + only one parameter can be selected which is shown as below: + \arg USART_DENT_ENABLE: DMA enable for transmission + \arg USART_DENT_DISABLE: DMA disable for transmission + \param[out] none + \retval none +*/ +void usart_dma_transmit_config(uint32_t usart_periph, uint32_t dmacmd) +{ + uint32_t ctl = 0U; + + ctl = USART_CTL2(usart_periph); + ctl &= ~USART_CTL2_DENT; + ctl |= dmacmd; + /* configure DMA transmission */ + USART_CTL2(usart_periph) = ctl; +} + +/*! + \brief get flag in STAT register + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] flag: USART flags, refer to usart_flag_enum + only one parameter can be selected which is shown as below: + \arg USART_FLAG_CTSF: CTS change flag + \arg USART_FLAG_LBDF: LIN break detected flag + \arg USART_FLAG_TBE: transmit data buffer empty + \arg USART_FLAG_TC: transmission complete + \arg USART_FLAG_RBNE: read data buffer not empty + \arg USART_FLAG_IDLEF: IDLE frame detected flag + \arg USART_FLAG_ORERR: overrun error + \arg USART_FLAG_NERR: noise error flag + \arg USART_FLAG_FERR: frame error flag + \arg USART_FLAG_PERR: parity error flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus usart_flag_get(uint32_t usart_periph, usart_flag_enum flag) +{ + if(RESET != (USART_REG_VAL(usart_periph, flag) & BIT(USART_BIT_POS(flag)))){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear flag in STAT register + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] flag: USART flags, refer to usart_flag_enum + only one parameter can be selected which is shown as below: + \arg USART_FLAG_CTSF: CTS change flag + \arg USART_FLAG_LBDF: LIN break detected flag + \arg USART_FLAG_TC: transmission complete + \arg USART_FLAG_RBNE: read data buffer not empty + \param[out] none + \retval none +*/ +void usart_flag_clear(uint32_t usart_periph, usart_flag_enum flag) +{ + USART_REG_VAL(usart_periph, flag) &= ~BIT(USART_BIT_POS(flag)); +} + +/*! + \brief enable USART interrupt + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] int_flag + only one parameter can be selected which is shown as below: + \arg USART_INT_PERR: parity error interrupt + \arg USART_INT_TBE: transmitter buffer empty interrupt + \arg USART_INT_TC: transmission complete interrupt + \arg USART_INT_RBNE: read data buffer not empty interrupt and overrun error interrupt + \arg USART_INT_IDLE: IDLE line detected interrupt + \arg USART_INT_LBD: LIN break detected interrupt + \arg USART_INT_ERR: error interrupt + \arg USART_INT_CTS: CTS interrupt + \param[out] none + \retval none +*/ +void usart_interrupt_enable(uint32_t usart_periph, uint32_t int_flag) +{ + USART_REG_VAL(usart_periph, int_flag) |= BIT(USART_BIT_POS(int_flag)); +} + +/*! + \brief disable USART interrupt + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] int_flag + only one parameter can be selected which is shown as below: + \arg USART_INT_PERR: parity error interrupt + \arg USART_INT_TBE: transmitter buffer empty interrupt + \arg USART_INT_TC: transmission complete interrupt + \arg USART_INT_RBNE: read data buffer not empty interrupt and overrun error interrupt + \arg USART_INT_IDLE: IDLE line detected interrupt + \arg USART_INT_LBD: LIN break detected interrupt + \arg USART_INT_ERR: error interrupt + \arg USART_INT_CTS: CTS interrupt + \param[out] none + \retval none +*/ +void usart_interrupt_disable(uint32_t usart_periph, uint32_t int_flag) +{ + USART_REG_VAL(usart_periph, int_flag) &= ~BIT(USART_BIT_POS(int_flag)); +} + +/*! + \brief get USART interrupt and flag status + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] int_flag + only one parameter can be selected which is shown as below: + \arg USART_INT_FLAG_PERR: parity error interrupt and flag + \arg USART_INT_FLAG_TBE: transmitter buffer empty interrupt and flag + \arg USART_INT_FLAG_TC: transmission complete interrupt and flag + \arg USART_INT_FLAG_RBNE: read data buffer not empty interrupt and flag + \arg USART_INT_FLAG_RBNE_ORERR: read data buffer not empty interrupt and overrun error flag + \arg USART_INT_FLAG_IDLE: IDLE line detected interrupt and flag + \arg USART_INT_FLAG_LBD: LIN break detected interrupt and flag + \arg USART_INT_FLAG_CTS: CTS interrupt and flag + \arg USART_INT_FLAG_ERR_ORERR: error interrupt and overrun error + \arg USART_INT_FLAG_ERR_NERR: error interrupt and noise error flag + \arg USART_INT_FLAG_ERR_FERR: error interrupt and frame error flag + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus usart_interrupt_flag_get(uint32_t usart_periph, uint32_t int_flag) +{ + uint32_t intenable = 0U, flagstatus = 0U; + /* get the interrupt enable bit status */ + intenable = (USART_REG_VAL(usart_periph, int_flag) & BIT(USART_BIT_POS(int_flag))); + /* get the corresponding flag bit status */ + flagstatus = (USART_REG_VAL2(usart_periph, int_flag) & BIT(USART_BIT_POS2(int_flag))); + + if(flagstatus && intenable){ + return SET; + }else{ + return RESET; + } +} + +/*! + \brief clear USART interrupt flag in STAT register + \param[in] usart_periph: USARTx(x=0,1,2)/UARTx(x=3,4) + \param[in] flag: USART interrupt flag + only one parameter can be selected which is shown as below: + \arg USART_INT_FLAG_CTS: CTS change flag + \arg USART_INT_FLAG_LBD: LIN break detected flag + \arg USART_INT_FLAG_TC: transmission complete + \arg USART_INT_FLAG_RBNE: read data buffer not empty + \param[out] none + \retval none +*/ +void usart_interrupt_flag_clear(uint32_t usart_periph, uint32_t flag) +{ + USART_REG_VAL2(usart_periph, flag) &= ~BIT(USART_BIT_POS2(flag)); +} + +int usart_write(uint32_t usart_periph,int ch) +{ + usart_data_transmit(usart_periph, (uint8_t) ch ); + while (usart_flag_get(usart_periph, USART_FLAG_TBE)== RESET){ + } + + return ch; +} + + +uint8_t usart_read(uint32_t usart_periph) +{ + /* loop until RBNE = 1 */ + while (usart_flag_get(usart_periph, USART_FLAG_RBNE) == RESET); + return(usart_data_receive(usart_periph)); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_wwdgt.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_wwdgt.c new file mode 100644 index 00000000..e4413486 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Drivers/gd32vf103_wwdgt.c @@ -0,0 +1,146 @@ +/*! + \file gd32vf103_wwdgt.c + \brief WWDGT driver + + \version 2019-6-5, V1.0.0, firmware for GD32VF103 +*/ + +/* + Copyright (c) 2019, GigaDevice Semiconductor Inc. + + Redistribution and use in source and binary forms, with or without modification, +are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, this + list of conditions and the following disclaimer. + 2. Redistributions in binary form must reproduce the above copyright notice, + this list of conditions and the following disclaimer in the documentation + and/or other materials provided with the distribution. + 3. Neither the name of the copyright holder nor the names of its contributors + may be used to endorse or promote products derived from this software without + specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED +WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. +IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, +INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT +NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY +OF SUCH DAMAGE. +*/ + +#include "gd32vf103_wwdgt.h" + +/* write value to WWDGT_CTL_CNT bit field */ +#define CTL_CNT(regval) (BITS(0,6) & ((uint32_t)(regval) << 0)) +/* write value to WWDGT_CFG_WIN bit field */ +#define CFG_WIN(regval) (BITS(0,6) & ((uint32_t)(regval) << 0)) + +/*! + \brief reset the window watchdog timer configuration + \param[in] none + \param[out] none + \retval none +*/ +void wwdgt_deinit(void) +{ + rcu_periph_reset_enable(RCU_WWDGTRST); + rcu_periph_reset_disable(RCU_WWDGTRST); +} + +/*! + \brief start the window watchdog timer counter + \param[in] none + \param[out] none + \retval none +*/ +void wwdgt_enable(void) +{ + WWDGT_CTL |= WWDGT_CTL_WDGTEN; +} + +/*! + \brief configure the window watchdog timer counter value + \param[in] counter_value: 0x00 - 0x7F + \param[out] none + \retval none +*/ +void wwdgt_counter_update(uint16_t counter_value) +{ + uint32_t reg = 0U; + + reg = (WWDGT_CTL & (~WWDGT_CTL_CNT)); + reg |= CTL_CNT(counter_value); + + WWDGT_CTL = reg; +} + +/*! + \brief configure counter value, window value, and prescaler divider value + \param[in] counter: 0x00 - 0x7F + \param[in] window: 0x00 - 0x7F + \param[in] prescaler: wwdgt prescaler value + only one parameter can be selected which is shown as below: + \arg WWDGT_CFG_PSC_DIV1: the time base of window watchdog counter = (PCLK1/4096)/1 + \arg WWDGT_CFG_PSC_DIV2: the time base of window watchdog counter = (PCLK1/4096)/2 + \arg WWDGT_CFG_PSC_DIV4: the time base of window watchdog counter = (PCLK1/4096)/4 + \arg WWDGT_CFG_PSC_DIV8: the time base of window watchdog counter = (PCLK1/4096)/8 + \param[out] none + \retval none +*/ +void wwdgt_config(uint16_t counter, uint16_t window, uint32_t prescaler) +{ + uint32_t reg_cfg = 0U, reg_ctl = 0U; + + /* clear WIN and PSC bits, clear CNT bit */ + reg_cfg = (WWDGT_CFG &(~(WWDGT_CFG_WIN|WWDGT_CFG_PSC))); + reg_ctl = (WWDGT_CTL &(~WWDGT_CTL_CNT)); + + /* configure WIN and PSC bits, configure CNT bit */ + reg_cfg |= CFG_WIN(window); + reg_cfg |= prescaler; + reg_ctl |= CTL_CNT(counter); + + WWDGT_CTL = reg_ctl; + WWDGT_CFG = reg_cfg; +} + +/*! + \brief enable early wakeup interrupt of WWDGT + \param[in] none + \param[out] none + \retval none +*/ +void wwdgt_interrupt_enable(void) +{ + WWDGT_CFG |= WWDGT_CFG_EWIE; +} + +/*! + \brief check early wakeup interrupt state of WWDGT + \param[in] none + \param[out] none + \retval FlagStatus: SET or RESET +*/ +FlagStatus wwdgt_flag_get(void) +{ + if(WWDGT_STAT & WWDGT_STAT_EWIF){ + return SET; + } + + return RESET; +} + +/*! + \brief clear early wakeup interrupt state of WWDGT + \param[in] none + \param[out] none + \retval none +*/ +void wwdgt_flag_clear(void) +{ + WWDGT_STAT &= (~WWDGT_STAT_EWIF); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/intexc_gd32vf103.S b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/intexc_gd32vf103.S new file mode 100644 index 00000000..9298f554 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/intexc_gd32vf103.S @@ -0,0 +1,232 @@ +/* + * Copyright (c) 2019 Nuclei Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +/****************************************************************************** + * \file intexc_gd32vf103.S + * \brief NMSIS Interrupt and Exception Handling Template File + * for Device gd32vf103 + * \version V1.00 + * \date 7 Jan 2020 + * + ******************************************************************************/ + +#include "riscv_encoding.h" + +/** + * \brief Global interrupt disabled + * \details + * This function disable global interrupt. + * \remarks + * - All the interrupt requests will be ignored by CPU. + */ +.macro DISABLE_MIE + csrc CSR_MSTATUS, MSTATUS_MIE +.endm + +/** + * \brief Macro for context save + * \details + * This macro save ABI defined caller saved registers in the stack. + * \remarks + * - This Macro could use to save context when you enter to interrupt + * or exception +*/ +/* Save caller registers */ +.macro SAVE_CONTEXT + /* Allocate stack space for context saving */ +#ifndef __riscv_32e + addi sp, sp, -20*REGBYTES +#else + addi sp, sp, -14*REGBYTES +#endif /* __riscv_32e */ + + STORE x1, 0*REGBYTES(sp) + STORE x4, 1*REGBYTES(sp) + STORE x5, 2*REGBYTES(sp) + STORE x6, 3*REGBYTES(sp) + STORE x7, 4*REGBYTES(sp) + STORE x10, 5*REGBYTES(sp) + STORE x11, 6*REGBYTES(sp) + STORE x12, 7*REGBYTES(sp) + STORE x13, 8*REGBYTES(sp) + STORE x14, 9*REGBYTES(sp) + STORE x15, 10*REGBYTES(sp) +#ifndef __riscv_32e + STORE x16, 14*REGBYTES(sp) + STORE x17, 15*REGBYTES(sp) + STORE x28, 16*REGBYTES(sp) + STORE x29, 17*REGBYTES(sp) + STORE x30, 18*REGBYTES(sp) + STORE x31, 19*REGBYTES(sp) +#endif /* __riscv_32e */ +.endm + +/** + * \brief Macro for restore caller registers + * \details + * This macro restore ABI defined caller saved registers from stack. + * \remarks + * - You could use this macro to restore context before you want return + * from interrupt or exeception + */ +/* Restore caller registers */ +.macro RESTORE_CONTEXT + LOAD x1, 0*REGBYTES(sp) + LOAD x4, 1*REGBYTES(sp) + LOAD x5, 2*REGBYTES(sp) + LOAD x6, 3*REGBYTES(sp) + LOAD x7, 4*REGBYTES(sp) + LOAD x10, 5*REGBYTES(sp) + LOAD x11, 6*REGBYTES(sp) + LOAD x12, 7*REGBYTES(sp) + LOAD x13, 8*REGBYTES(sp) + LOAD x14, 9*REGBYTES(sp) + LOAD x15, 10*REGBYTES(sp) +#ifndef __riscv_32e + LOAD x16, 14*REGBYTES(sp) + LOAD x17, 15*REGBYTES(sp) + LOAD x28, 16*REGBYTES(sp) + LOAD x29, 17*REGBYTES(sp) + LOAD x30, 18*REGBYTES(sp) + LOAD x31, 19*REGBYTES(sp) + + /* De-allocate the stack space */ + addi sp, sp, 20*REGBYTES +#else + /* De-allocate the stack space */ + addi sp, sp, 14*REGBYTES +#endif /* __riscv_32e */ + +.endm + +/** + * \brief Macro for save necessary CSRs to stack + * \details + * This macro store MCAUSE, MEPC, MSUBM to stack. + */ +.macro SAVE_CSR_CONTEXT + /* Store CSR mcause to stack using pushmcause */ + csrrwi x0, CSR_PUSHMCAUSE, 11 + /* Store CSR mepc to stack using pushmepc */ + csrrwi x0, CSR_PUSHMEPC, 12 + /* Store CSR msub to stack using pushmsub */ + csrrwi x0, CSR_PUSHMSUBM, 13 +.endm + +/** + * \brief Macro for restore necessary CSRs from stack + * \details + * This macro restore MSUBM, MEPC, MCAUSE from stack. + */ +.macro RESTORE_CSR_CONTEXT + LOAD x5, 13*REGBYTES(sp) + csrw CSR_MSUBM, x5 + LOAD x5, 12*REGBYTES(sp) + csrw CSR_MEPC, x5 + LOAD x5, 11*REGBYTES(sp) + csrw CSR_MCAUSE, x5 +.endm + +/** + * \brief Exception/NMI Entry + * \details + * This function provide common entry functions for exception/nmi. + * \remarks + * This function provide a default exception/nmi entry. + * ABI defined caller save register and some CSR registers + * to be saved before enter interrupt handler and be restored before return. + */ +.section .text.trap +/* In CLIC mode, the exeception entry must be 64bytes aligned */ +.align 6 +.global exc_entry +.weak exc_entry +exc_entry: + /* Save the caller saving registers (context) */ + SAVE_CONTEXT + /* Save the necessary CSR registers */ + SAVE_CSR_CONTEXT + + /* + * Set the exception handler function arguments + * argument 1: mcause value + * argument 2: current stack point(SP) value + */ + csrr a0, mcause + mv a1, sp + /* + * TODO: Call the exception handler function + * By default, the function template is provided in + * system_Device.c, you can adjust it as you want + */ + call core_exception_handler + + /* Restore the necessary CSR registers */ + RESTORE_CSR_CONTEXT + /* Restore the caller saving registers (context) */ + RESTORE_CONTEXT + + /* Return to regular code */ + mret + +/** + * \brief Non-Vector Interrupt Entry + * \details + * This function provide common entry functions for handling + * non-vector interrupts + * \remarks + * This function provide a default non-vector interrupt entry. + * ABI defined caller save register and some CSR registers need + * to be saved before enter interrupt handler and be restored before return. + */ +.section .text.irq +/* In CLIC mode, the interrupt entry must be 4bytes aligned */ +.align 2 +.global irq_entry +.weak irq_entry +/* This label will be set to MTVT2 register */ +irq_entry: + /* Save the caller saving registers (context) */ + SAVE_CONTEXT + /* Save the necessary CSR registers */ + SAVE_CSR_CONTEXT + + /* This special CSR read/write operation, which is actually + * claim the CLIC to find its pending highest ID, if the ID + * is not 0, then automatically enable the mstatus.MIE, and + * jump to its vector-entry-label, and update the link register + */ + csrrw ra, CSR_JALMNXTI, ra + + /* Critical section with interrupts disabled */ + DISABLE_MIE + + /* Restore the necessary CSR registers */ + RESTORE_CSR_CONTEXT + /* Restore the caller saving registers (context) */ + RESTORE_CONTEXT + + /* Return to regular code */ + mret + +/* Default Handler for Exceptions / Interrupts */ +.global default_intexc_handler +.weak default_intexc_handler +Undef_Handler: +default_intexc_handler: +1: + j 1b diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/startup_gd32vf103.S b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/startup_gd32vf103.S new file mode 100644 index 00000000..eab20897 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/GCC/startup_gd32vf103.S @@ -0,0 +1,370 @@ +/* + * Copyright (c) 2019 Nuclei Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +/****************************************************************************** + * \file startup_gd32vf103.S + * \brief NMSIS Nuclei N/NX Class Core based Core Device Startup File for + * Device gd32vf103 + * \version V1.00 + * \date 21 Nov 2019 + * + * + ******************************************************************************/ + +#include "riscv_encoding.h" + +.macro DECLARE_INT_HANDLER INT_HDL_NAME +#if defined(__riscv_xlen) && (__riscv_xlen == 32) + .word \INT_HDL_NAME +#else + .dword \INT_HDL_NAME +#endif +.endm + + /* + * Put the interrupt vectors in this section according to the run mode: + * FlashXIP: .vtable + * ILM: .vtable + * Flash: .vtable_ilm + */ +#if defined(DOWNLOAD_MODE) && (DOWNLOAD_MODE == DOWNLOAD_MODE_FLASH) + .section .vtable_ilm +#else + .section .vtable +#endif + + .weak eclic_msip_handler + .weak eclic_mtip_handler + .weak eclic_bwei_handler + .weak eclic_pmovi_handler + .weak WWDGT_IRQHandler + .weak LVD_IRQHandler + .weak TAMPER_IRQHandler + .weak RTC_IRQHandler + .weak FMC_IRQHandler + .weak RCU_IRQHandler + .weak EXTI0_IRQHandler + .weak EXTI1_IRQHandler + .weak EXTI2_IRQHandler + .weak EXTI3_IRQHandler + .weak EXTI4_IRQHandler + .weak DMA0_Channel0_IRQHandler + .weak DMA0_Channel1_IRQHandler + .weak DMA0_Channel2_IRQHandler + .weak DMA0_Channel3_IRQHandler + .weak DMA0_Channel4_IRQHandler + .weak DMA0_Channel5_IRQHandler + .weak DMA0_Channel6_IRQHandler + .weak ADC0_1_IRQHandler + .weak CAN0_TX_IRQHandler + .weak CAN0_RX0_IRQHandler + .weak CAN0_RX1_IRQHandler + .weak CAN0_EWMC_IRQHandler + .weak EXTI5_9_IRQHandler + .weak TIMER0_BRK_IRQHandler + .weak TIMER0_UP_IRQHandler + .weak TIMER0_TRG_CMT_IRQHandler + .weak TIMER0_Channel_IRQHandler + .weak TIMER1_IRQHandler + .weak TIMER2_IRQHandler + .weak TIMER3_IRQHandler + .weak I2C0_EV_IRQHandler + .weak I2C0_ER_IRQHandler + .weak I2C1_EV_IRQHandler + .weak I2C1_ER_IRQHandler + .weak SPI0_IRQHandler + .weak SPI1_IRQHandler + .weak USART0_IRQHandler + .weak USART1_IRQHandler + .weak USART2_IRQHandler + .weak EXTI10_15_IRQHandler + .weak RTC_Alarm_IRQHandler + .weak USBFS_WKUP_IRQHandler + .weak EXMC_IRQHandler + .weak TIMER4_IRQHandler + .weak SPI2_IRQHandler + .weak UART3_IRQHandler + .weak UART4_IRQHandler + .weak TIMER5_IRQHandler + .weak TIMER6_IRQHandler + .weak DMA1_Channel0_IRQHandler + .weak DMA1_Channel1_IRQHandler + .weak DMA1_Channel2_IRQHandler + .weak DMA1_Channel3_IRQHandler + .weak DMA1_Channel4_IRQHandler + .weak CAN1_TX_IRQHandler + .weak CAN1_RX0_IRQHandler + .weak CAN1_RX1_IRQHandler + .weak CAN1_EWMC_IRQHandler + .weak USBFS_IRQHandler + + + .globl vector_base + .type vector_base, @object +vector_base: +#if defined(DOWNLOAD_MODE) && (DOWNLOAD_MODE != DOWNLOAD_MODE_FLASH) + j _start /* 0: Reserved, Jump to _start when reset for ILM/FlashXIP mode.*/ + .align LOG_REGBYTES /* Need to align 4 byte for RV32, 8 Byte for RV64 */ +#else + DECLARE_INT_HANDLER default_intexc_handler /* 0: Reserved, default handler for Flash download mode */ +#endif + DECLARE_INT_HANDLER default_intexc_handler /* 1: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 2: Reserved */ + DECLARE_INT_HANDLER eclic_msip_handler /* 3: Machine software interrupt */ + + DECLARE_INT_HANDLER default_intexc_handler /* 4: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 5: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 6: Reserved */ + DECLARE_INT_HANDLER eclic_mtip_handler /* 7: Machine timer interrupt */ + + DECLARE_INT_HANDLER default_intexc_handler /* 8: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 9: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 10: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 11: Reserved */ + + DECLARE_INT_HANDLER default_intexc_handler /* 12: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 13: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 14: Reserved */ + DECLARE_INT_HANDLER default_intexc_handler /* 15: Reserved */ + + DECLARE_INT_HANDLER default_intexc_handler /* 16: Reserved */ + DECLARE_INT_HANDLER eclic_bwei_handler /* 17: Bus Error interrupt */ + DECLARE_INT_HANDLER eclic_pmovi_handler /* 18: Performance Monitor */ + + DECLARE_INT_HANDLER WWDGT_IRQHandler + DECLARE_INT_HANDLER LVD_IRQHandler + DECLARE_INT_HANDLER TAMPER_IRQHandler + DECLARE_INT_HANDLER RTC_IRQHandler + DECLARE_INT_HANDLER FMC_IRQHandler + DECLARE_INT_HANDLER RCU_IRQHandler + DECLARE_INT_HANDLER EXTI0_IRQHandler + DECLARE_INT_HANDLER EXTI1_IRQHandler + DECLARE_INT_HANDLER EXTI2_IRQHandler + DECLARE_INT_HANDLER EXTI3_IRQHandler + DECLARE_INT_HANDLER EXTI4_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel0_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel1_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel2_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel3_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel4_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel5_IRQHandler + DECLARE_INT_HANDLER DMA0_Channel6_IRQHandler + DECLARE_INT_HANDLER ADC0_1_IRQHandler + DECLARE_INT_HANDLER CAN0_TX_IRQHandler + DECLARE_INT_HANDLER CAN0_RX0_IRQHandler + DECLARE_INT_HANDLER CAN0_RX1_IRQHandler + DECLARE_INT_HANDLER CAN0_EWMC_IRQHandler + DECLARE_INT_HANDLER EXTI5_9_IRQHandler + DECLARE_INT_HANDLER TIMER0_BRK_IRQHandler + DECLARE_INT_HANDLER TIMER0_UP_IRQHandler + DECLARE_INT_HANDLER TIMER0_TRG_CMT_IRQHandler + DECLARE_INT_HANDLER TIMER0_Channel_IRQHandler + DECLARE_INT_HANDLER TIMER1_IRQHandler + DECLARE_INT_HANDLER TIMER2_IRQHandler + DECLARE_INT_HANDLER TIMER3_IRQHandler + DECLARE_INT_HANDLER I2C0_EV_IRQHandler + DECLARE_INT_HANDLER I2C0_ER_IRQHandler + DECLARE_INT_HANDLER I2C1_EV_IRQHandler + DECLARE_INT_HANDLER I2C1_ER_IRQHandler + DECLARE_INT_HANDLER SPI0_IRQHandler + DECLARE_INT_HANDLER SPI1_IRQHandler + DECLARE_INT_HANDLER USART0_IRQHandler + DECLARE_INT_HANDLER USART1_IRQHandler + DECLARE_INT_HANDLER USART2_IRQHandler + DECLARE_INT_HANDLER EXTI10_15_IRQHandler + DECLARE_INT_HANDLER RTC_Alarm_IRQHandler + DECLARE_INT_HANDLER USBFS_WKUP_IRQHandler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER EXMC_IRQHandler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER TIMER4_IRQHandler + DECLARE_INT_HANDLER SPI2_IRQHandler + DECLARE_INT_HANDLER UART3_IRQHandler + DECLARE_INT_HANDLER UART4_IRQHandler + DECLARE_INT_HANDLER TIMER5_IRQHandler + DECLARE_INT_HANDLER TIMER6_IRQHandler + DECLARE_INT_HANDLER DMA1_Channel0_IRQHandler + DECLARE_INT_HANDLER DMA1_Channel1_IRQHandler + DECLARE_INT_HANDLER DMA1_Channel2_IRQHandler + DECLARE_INT_HANDLER DMA1_Channel3_IRQHandler + DECLARE_INT_HANDLER DMA1_Channel4_IRQHandler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER default_intexc_handler + DECLARE_INT_HANDLER CAN1_TX_IRQHandler + DECLARE_INT_HANDLER CAN1_RX0_IRQHandler + DECLARE_INT_HANDLER CAN1_RX1_IRQHandler + DECLARE_INT_HANDLER CAN1_EWMC_IRQHandler + DECLARE_INT_HANDLER USBFS_IRQHandler + + .section .init + + .globl _start + .type _start, @function + +/** + * Reset Handler called on controller reset + */ +_start: + /* ===== Startup Stage 1 ===== */ + /* Disable Global Interrupt */ + csrc CSR_MSTATUS, MSTATUS_MIE + /* Jump to logical address first to ensure correct operation of RAM region */ + la a0, _start + li a1, 1 + slli a1, a1, 29 + bleu a1, a0, _start0800 + srli a1, a1, 2 + bleu a1, a0, _start0800 + la a0, _start0800 + add a0, a0, a1 + jr a0 + +_start0800: + /* Initialize GP and Stack Pointer SP */ + .option push + .option norelax + la gp, __global_pointer$ + + .option pop + la sp, _sp + + /* + * Set the the NMI base mnvec to share + * with mtvec by setting CSR_MMISC_CTL + * bit 9 NMI_CAUSE_FFF to 1 + */ + li t0, MMISC_CTL_NMI_CAUSE_FFF + csrs CSR_MMISC_CTL, t0 + + /* + * Intialize ECLIC vector interrupt + * base address mtvt to vector_base + */ + la t0, vector_base + csrw CSR_MTVT, t0 + + /* + * Set ECLIC non-vector entry to be controlled + * by mtvt2 CSR register. + * Intialize ECLIC non-vector interrupt + * base address mtvt2 to irq_entry. + */ + la t0, irq_entry + csrw CSR_MTVT2, t0 + csrs CSR_MTVT2, 0x1 + + /* + * Set Exception Entry MTVEC to exc_entry + * Due to settings above, Exception and NMI + * will share common entry. + */ + la t0, exc_entry + csrw CSR_MTVEC, t0 + + /* Set the interrupt processing mode to ECLIC mode */ + li t0, 0x3f + csrc CSR_MTVEC, t0 + csrs CSR_MTVEC, 0x3 + + /* ===== Startup Stage 2 ===== */ + +#ifdef __riscv_flen + /* Enable FPU */ + li t0, MSTATUS_FS + csrs mstatus, t0 + csrw fcsr, x0 +#endif + + /* Enable mcycle and minstret counter */ + csrci CSR_MCOUNTINHIBIT, 0x5 + + /* ===== Startup Stage 3 ===== */ + /* + * Load code section from FLASH to ILM + * when code LMA is different with VMA + */ + la a0, _ilm_lma + la a1, _ilm + /* If the ILM phy-address same as the logic-address, then quit */ + beq a0, a1, 2f + la a2, _eilm + bgeu a1, a2, 2f + +1: + /* Load code section if necessary */ + lw t0, (a0) + sw t0, (a1) + addi a0, a0, 4 + addi a1, a1, 4 + bltu a1, a2, 1b +2: + /* Load data section */ + la a0, _data_lma + la a1, _data + la a2, _edata + bgeu a1, a2, 2f +1: + lw t0, (a0) + sw t0, (a1) + addi a0, a0, 4 + addi a1, a1, 4 + bltu a1, a2, 1b +2: + /* Clear bss section */ + la a0, __bss_start + la a1, _end + bgeu a0, a1, 2f +1: + sw zero, (a0) + addi a0, a0, 4 + bltu a0, a1, 1b +2: + + /* + * Call vendor defined SystemInit to + * initialize the micro-controller system + */ + call SystemInit + + /* Call global constructors */ + la a0, __libc_fini_array + call atexit + /* Call C/C++ constructor start up code */ + call __libc_init_array + + /* do pre-init steps before main */ + call _premain_init + /* ===== Call Main Function ===== */ + /* argc = argv = 0 */ + li a0, 0 + li a1, 0 + +#ifdef RTOS_RTTHREAD + // Call entry function when using RT-Thread + call entry +#else + call main +#endif + /* do post-main steps after main */ + call _postmain_fini + +1: + j 1b diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_getres.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_getres.c new file mode 100644 index 00000000..820f5146 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_getres.c @@ -0,0 +1,14 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#include +#include + +/* Get resolution of clock. */ +__WEAK int clock_getres(clockid_t clock_id, struct timespec *res) +{ + res->tv_sec = 0; + res->tv_nsec = 1000000000 / SystemCoreClock; + + return 0; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_gettime.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_gettime.c new file mode 100644 index 00000000..8f4ca46b --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_gettime.c @@ -0,0 +1,21 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#include +#include + +extern int _gettimeofday(struct timeval *tp, void *tzp); + +/* Get current value of CLOCK and store it in tp. */ +__WEAK int clock_gettime(clockid_t clock_id, struct timespec *tp) +{ + struct timeval tv; + int retval = -1; + + retval = _gettimeofday(&tv, NULL); + if (retval == 0) { + TIMEVAL_TO_TIMESPEC(&tv, tp); + } + + return retval; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_settime.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_settime.c new file mode 100644 index 00000000..caa2936d --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/clock_settime.c @@ -0,0 +1,10 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#include + +/* Set CLOCK to value TP. */ +__WEAK int clock_settime(clockid_t clock_id, const struct timespec *tp) +{ + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/close.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/close.c new file mode 100644 index 00000000..ac2fae9f --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/close.c @@ -0,0 +1,12 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +#undef errno +extern int errno; + +__WEAK int _close(int fd) +{ + errno = EBADF; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/execve.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/execve.c new file mode 100644 index 00000000..b4386247 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/execve.c @@ -0,0 +1,12 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +#undef errno +extern int errno; + +__WEAK int _execve(char *name, char **argv, char **env) +{ + errno = ENOMEM; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/exit.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/exit.c new file mode 100644 index 00000000..0e33d9f2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/exit.c @@ -0,0 +1,9 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" + +__WEAK void _exit(int fd) +{ + while(1) { + __WFI(); + } +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fork.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fork.c new file mode 100644 index 00000000..fddb47be --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fork.c @@ -0,0 +1,12 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +#undef errno +extern int errno; + +__WEAK int _fork(void) +{ + errno = EAGAIN; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fstat.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fstat.c new file mode 100644 index 00000000..2cffbb47 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/fstat.c @@ -0,0 +1,19 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#include +#include + +#undef errno +extern int errno; + +__WEAK int _fstat(int file, struct stat *st) +{ + if ((STDOUT_FILENO == file) || (STDERR_FILENO == file)) { + st->st_mode = S_IFCHR; + return 0; + } else { + errno = EBADF; + return -1; + } +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/getpid.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/getpid.c new file mode 100644 index 00000000..362f5cfe --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/getpid.c @@ -0,0 +1,8 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +__WEAK int _getpid(void) +{ + return 1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/gettimeofday.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/gettimeofday.c new file mode 100644 index 00000000..ec60a655 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/gettimeofday.c @@ -0,0 +1,15 @@ +/* See LICENSE of license details. */ +#include +#include +#include "nuclei_sdk_soc.h" + +__WEAK int _gettimeofday(struct timeval *tp, void *tzp) +{ + uint64_t cycles; + + cycles = __get_rv_cycle(); + + tp->tv_sec = cycles / SystemCoreClock; + tp->tv_usec = (cycles % SystemCoreClock) * 1000000 / SystemCoreClock; + return 0; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/isatty.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/isatty.c new file mode 100644 index 00000000..d7f29b31 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/isatty.c @@ -0,0 +1,8 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +__WEAK int _isatty(int fd) +{ + return 1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/kill.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/kill.c new file mode 100644 index 00000000..ffad3493 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/kill.c @@ -0,0 +1,11 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#undef errno +extern int errno; + +__WEAK int _kill(int pid, int sig) +{ + errno = EINVAL; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/link.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/link.c new file mode 100644 index 00000000..59cdd3d9 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/link.c @@ -0,0 +1,12 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +#undef errno +extern int errno; + +int _link(char *old, char *new) +{ + errno = EMLINK; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/lseek.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/lseek.c new file mode 100644 index 00000000..90e4d13a --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/lseek.c @@ -0,0 +1,11 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +#undef errno +extern int errno; + +__WEAK int _lseek(int file, int offset, int whence) +{ + return 0; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/open.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/open.c new file mode 100644 index 00000000..d41d2770 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/open.c @@ -0,0 +1,12 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +#undef errno +extern int errno; + +__WEAK int _open(const char *name, int flags, int mode) +{ + errno = ENOSYS; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/read.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/read.c new file mode 100644 index 00000000..1be28d61 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/read.c @@ -0,0 +1,22 @@ +/* See LICENSE of license details. */ +#include +#include +#include +#include +#include "nuclei_sdk_hal.h" + +// #define UART_AUTO_ECHO + +__WEAK ssize_t _read(int fd, void* ptr, size_t len) +{ + if (fd != STDIN_FILENO) { + return -1; + } + + uint8_t *readbuf = (uint8_t *)ptr; + readbuf[0] = usart_read(SOC_DEBUG_UART); +#ifdef UART_AUTO_ECHO + usart_write(SOC_DEBUG_UART, (int)readbuf[0]); +#endif + return 1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/sbrk.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/sbrk.c new file mode 100644 index 00000000..301ef4d2 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/sbrk.c @@ -0,0 +1,19 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#include +#include + +__WEAK void *_sbrk(ptrdiff_t incr) +{ + extern char _end[]; + extern char _heap_end[]; + static char *curbrk = _end; + + if ((curbrk + incr < _end) || (curbrk + incr > _heap_end)) { + return (void *)(-1); + } + + curbrk += incr; + return (void *)(curbrk - incr); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/stat.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/stat.c new file mode 100644 index 00000000..e07c335e --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/stat.c @@ -0,0 +1,9 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include + +__WEAK int _stat(char *file, struct stat *st) +{ + st->st_mode = S_IFCHR; + return 0; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/times.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/times.c new file mode 100644 index 00000000..745be651 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/times.c @@ -0,0 +1,27 @@ +/* See LICENSE of license details. */ +#include +#include +#include +#include "nuclei_sdk_soc.h" + +extern int _gettimeofday(struct timeval *, void *); + +__WEAK clock_t _times(struct tms *buf) +{ + static struct timeval t0; + struct timeval t; + long long utime; + + /* When called for the first time, initialize t0. */ + if (t0.tv_sec == 0 && t0.tv_usec == 0) { + _gettimeofday(&t0, 0); + } + + _gettimeofday(&t, 0); + + utime = (t.tv_sec - t0.tv_sec) * 1000000 + (t.tv_usec - t0.tv_usec); + buf->tms_utime = utime * CLOCKS_PER_SEC / 1000000; + buf->tms_stime = buf->tms_cstime = buf->tms_cutime = 0; + + return buf->tms_utime; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/unlink.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/unlink.c new file mode 100644 index 00000000..3662c546 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/unlink.c @@ -0,0 +1,12 @@ + +/* See LICENSE of license details. */ +#include +#include "nuclei_sdk_hal.h" + +#undef errno +extern int errno; + +__WEAK int _unlink(const char *name) +{ + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/wait.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/wait.c new file mode 100644 index 00000000..49e1e933 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/wait.c @@ -0,0 +1,13 @@ +/* See LICENSE of license details. */ +#include "nuclei_sdk_soc.h" +#include +#include + +#undef errno +extern int errno; + +__WEAK int _wait(int *status) +{ + errno = ECHILD; + return -1; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/write.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/write.c new file mode 100644 index 00000000..7d48e090 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/Stubs/write.c @@ -0,0 +1,22 @@ +/* See LICENSE of license details. */ +#include +#include +#include +#include +#include "nuclei_sdk_hal.h" + +__WEAK ssize_t _write(int fd, const void* ptr, size_t len) +{ + if (!isatty(fd)) { + return -1; + } + + const uint8_t *writebuf = (const uint8_t *)ptr; + for (size_t i = 0; i < len; i++) { + if (writebuf[i] == '\n') { + usart_write(SOC_DEBUG_UART, '\r'); + } + usart_write(SOC_DEBUG_UART, writebuf[i]); + } + return len; +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/gd32vf103_soc.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/gd32vf103_soc.c new file mode 100644 index 00000000..3de68037 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/gd32vf103_soc.c @@ -0,0 +1,59 @@ +#include "nuclei_sdk_soc.h" + +static uint32_t get_timer_freq() +{ + return SOC_TIMER_FREQ; +} + +uint32_t measure_cpu_freq(uint32_t n) +{ + uint32_t start_mcycle, delta_mcycle; + uint32_t start_mtime, delta_mtime; + uint32_t mtime_freq = get_timer_freq(); + + // Don't start measuruing until we see an mtime tick + uint32_t tmp = (uint32_t)SysTimer_GetLoadValue(); + do { + start_mtime = (uint32_t)SysTimer_GetLoadValue(); + start_mcycle = __RV_CSR_READ(CSR_MCYCLE); + } while (start_mtime == tmp); + + do { + delta_mtime = (uint32_t)SysTimer_GetLoadValue() - start_mtime; + delta_mcycle = __RV_CSR_READ(CSR_MCYCLE) - start_mcycle; + } while (delta_mtime < n); + + return (delta_mcycle / delta_mtime) * mtime_freq + + ((delta_mcycle % delta_mtime) * mtime_freq) / delta_mtime; +} + +uint32_t get_cpu_freq() +{ + uint32_t cpu_freq; + + // warm up + measure_cpu_freq(1); + // measure for real + cpu_freq = measure_cpu_freq(100); + + return cpu_freq; +} + +/** + * \brief delay a time in milliseconds + * \details + * provide API for delay + * \param[in] count: count in milliseconds + * \remarks + */ +void delay_1ms(uint32_t count) +{ + uint64_t start_mtime, delta_mtime; + uint64_t delay_ticks = (SOC_TIMER_FREQ * (uint64_t)count) / 1000; + + start_mtime = SysTimer_GetLoadValue(); + + do { + delta_mtime = SysTimer_GetLoadValue() - start_mtime; + } while (delta_mtime < delay_ticks); +} diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/system_gd32vf103.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/system_gd32vf103.c new file mode 100644 index 00000000..3ed8d65d --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/SoC/gd32vf103/Common/Source/system_gd32vf103.c @@ -0,0 +1,584 @@ +/****************************************************************************** + * @file system_gd32vf103.c + * @brief NMSIS Nuclei Core Device Peripheral Access Layer Source File for + * Device gd32vf103 + * @version V1.00 + * @date 22. Nov 2019 + ******************************************************************************/ +/* + * Copyright (c) 2009-2018 Arm Limited. All rights reserved. + * Copyright (c) 2019 Nuclei Limited. All rights reserved. + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the License); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +#include +#include +#include "nuclei_sdk_hal.h" +#include "los_arch_interrupt.h" +#include "los_debug.h" +/*---------------------------------------------------------------------------- + Define clocks + *----------------------------------------------------------------------------*/ +/* ToDo: add here your necessary defines for device initialization + following is an example for different system frequencies */ +#ifndef SYSTEM_CLOCK +#define SYSTEM_CLOCK __SYSTEM_CLOCK_108M_PLL_HXTAL +#endif + +/** + * \defgroup NMSIS_Core_SystemAndClock System and Clock Configuration + * \brief Functions for system and clock setup available in system_.c. + * \details + * Nuclei provides a template file **system_Device.c** that must be adapted by + * the silicon vendor to match their actual device. As a minimum requirement, + * this file must provide: + * - A device-specific system configuration function, \ref SystemInit(). + * - A global variable that contains the system frequency, \ref SystemCoreClock. + * + * The file configures the device and, typically, initializes the oscillator (PLL) that is part + * of the microcontroller device. This file might export other functions or variables that provide + * a more flexible configuration of the microcontroller system. + * + * \note Please pay special attention to the static variable \c SystemCoreClock. This variable might be + * used throughout the whole system initialization and runtime to calculate frequency/time related values. + * Thus one must assure that the variable always reflects the actual system clock speed. + * + * \attention + * Be aware that a value stored to \c SystemCoreClock during low level initialization (i.e. \c SystemInit()) might get + * overwritten by C libray startup code and/or .bss section initialization. + * Thus its highly recommended to call \ref SystemCoreClockUpdate at the beginning of the user \c main() routine. + * + * @{ + */ + +/*---------------------------------------------------------------------------- + System Core Clock Variable + *----------------------------------------------------------------------------*/ +/* ToDo: initialize SystemCoreClock with the system core clock frequency value + achieved after system intitialization. + This means system core clock frequency after call to SystemInit() */ +/** + * \brief Variable to hold the system core clock value + * \details + * Holds the system core clock, which is the system clock frequency supplied to the SysTick + * timer and the processor core clock. This variable can be used by debuggers to query the + * frequency of the debug timer or to configure the trace clock speed. + * + * \attention + * Compilers must be configured to avoid removing this variable in case the application + * program is not using it. Debugging systems require the variable to be physically + * present in memory so that it can be examined to configure the debugger. + */ +uint32_t SystemCoreClock = __SYSTEM_CLOCK_108M_PLL_HXTAL; /* System Clock Frequency (Core Clock) */ + +/*---------------------------------------------------------------------------- + Clock functions + *----------------------------------------------------------------------------*/ + +/*! + \brief configure the system clock to 108M by PLL which selects HXTAL(MD/HD/XD:8M; CL:25M) as its clock source + \param[in] none + \param[out] none + \retval none +*/ + +static void system_clock_108m_hxtal(void) +{ + uint32_t timeout = 0U; + uint32_t stab_flag = 0U; + + /* enable HXTAL */ + RCU_CTL |= RCU_CTL_HXTALEN; + + /* wait until HXTAL is stable or the startup time is longer than + * HXTAL_STARTUP_TIMEOUT */ + do { + timeout++; + stab_flag = (RCU_CTL & RCU_CTL_HXTALSTB); + } while ((0U == stab_flag) && (HXTAL_STARTUP_TIMEOUT != timeout)); + + /* if fail */ + if (0U == (RCU_CTL & RCU_CTL_HXTALSTB)) { + while (1) { + } + } + + /* HXTAL is stable */ + /* AHB = SYSCLK */ + RCU_CFG0 |= RCU_AHB_CKSYS_DIV1; + /* APB2 = AHB/1 */ + RCU_CFG0 |= RCU_APB2_CKAHB_DIV1; + /* APB1 = AHB/2 */ + RCU_CFG0 |= RCU_APB1_CKAHB_DIV2; + + /* CK_PLL = (CK_PREDIV0) * 27 = 108 MHz */ + RCU_CFG0 &= ~(RCU_CFG0_PLLMF | RCU_CFG0_PLLMF_4); + RCU_CFG0 |= (RCU_PLLSRC_HXTAL | RCU_PLL_MUL27); + + if (HXTAL_VALUE == 25000000) { + /* CK_PREDIV0 = (CK_HXTAL)/5 *8 /10 = 4 MHz */ + RCU_CFG1 &= ~(RCU_CFG1_PREDV0SEL | RCU_CFG1_PREDV1 | RCU_CFG1_PLL1MF | + RCU_CFG1_PREDV0); + RCU_CFG1 |= (RCU_PREDV0SRC_CKPLL1 | RCU_PREDV1_DIV5 | RCU_PLL1_MUL8 | + RCU_PREDV0_DIV10); + + /* enable PLL1 */ + RCU_CTL |= RCU_CTL_PLL1EN; + /* wait till PLL1 is ready */ + while (0U == (RCU_CTL & RCU_CTL_PLL1STB)) { + } + + /* enable PLL1 */ + RCU_CTL |= RCU_CTL_PLL2EN; + /* wait till PLL1 is ready */ + while (0U == (RCU_CTL & RCU_CTL_PLL2STB)) { + } + } else if (HXTAL_VALUE == 8000000) { + RCU_CFG1 &= ~(RCU_CFG1_PREDV0SEL | RCU_CFG1_PREDV1 | RCU_CFG1_PLL1MF | + RCU_CFG1_PREDV0); + RCU_CFG1 |= (RCU_PREDV0SRC_HXTAL | RCU_PREDV0_DIV2 | RCU_PREDV1_DIV2 | + RCU_PLL1_MUL20 | RCU_PLL2_MUL20); + + /* enable PLL1 */ + RCU_CTL |= RCU_CTL_PLL1EN; + /* wait till PLL1 is ready */ + while (0U == (RCU_CTL & RCU_CTL_PLL1STB)) { + } + + /* enable PLL2 */ + RCU_CTL |= RCU_CTL_PLL2EN; + /* wait till PLL1 is ready */ + while (0U == (RCU_CTL & RCU_CTL_PLL2STB)) { + } + } + /* enable PLL */ + RCU_CTL |= RCU_CTL_PLLEN; + + /* wait until PLL is stable */ + while (0U == (RCU_CTL & RCU_CTL_PLLSTB)) { + } + + /* select PLL as system clock */ + RCU_CFG0 &= ~RCU_CFG0_SCS; + RCU_CFG0 |= RCU_CKSYSSRC_PLL; + + /* wait until PLL is selected as system clock */ + while (0U == (RCU_CFG0 & RCU_SCSS_PLL)) { + } +} + +/*! + \brief configure the system clock + \param[in] none + \param[out] none + \retval none +*/ +static void system_clock_config(void) +{ + system_clock_108m_hxtal(); +} + + +/** + * \brief Function to update the variable \ref SystemCoreClock + * \details + * Updates the variable \ref SystemCoreClock and must be called whenever the core clock is changed + * during program execution. The function evaluates the clock register settings and calculates + * the current core clock. + */ +void SystemCoreClockUpdate (void) /* Get Core Clock Frequency */ +{ + /* ToDo: add code to calculate the system frequency based upon the current + * register settings. + * Note: This function can be used to retrieve the system core clock + * frequeny after user changed register settings. + */ + uint32_t scss; + uint32_t pllsel, predv0sel, pllmf, ck_src; + uint32_t predv0, predv1, pll1mf; + + scss = GET_BITS(RCU_CFG0, 2, 3); + + switch (scss) { + /* IRC8M is selected as CK_SYS */ + case SEL_IRC8M: + SystemCoreClock = IRC8M_VALUE; + break; + + /* HXTAL is selected as CK_SYS */ + case SEL_HXTAL: + SystemCoreClock = HXTAL_VALUE; + break; + + /* PLL is selected as CK_SYS */ + case SEL_PLL: + /* PLL clock source selection, HXTAL or IRC8M/2 */ + pllsel = (RCU_CFG0 & RCU_CFG0_PLLSEL); + + if (RCU_PLLSRC_IRC8M_DIV2 == pllsel) { + /* PLL clock source is IRC8M/2 */ + ck_src = IRC8M_VALUE / 2U; + } else { + /* PLL clock source is HXTAL */ + ck_src = HXTAL_VALUE; + + predv0sel = (RCU_CFG1 & RCU_CFG1_PREDV0SEL); + + /* source clock use PLL1 */ + if (RCU_PREDV0SRC_CKPLL1 == predv0sel) { + predv1 = ((RCU_CFG1 & RCU_CFG1_PREDV1) >> 4) + 1U; + pll1mf = ((RCU_CFG1 & RCU_CFG1_PLL1MF) >> 8) + 2U; + if (17U == pll1mf) { + pll1mf = 20U; + } + ck_src = (ck_src / predv1) * pll1mf; + } + predv0 = (RCU_CFG1 & RCU_CFG1_PREDV0) + 1U; + ck_src /= predv0; + } + + /* PLL multiplication factor */ + pllmf = GET_BITS(RCU_CFG0, 18, 21); + + if ((RCU_CFG0 & RCU_CFG0_PLLMF_4)) { + pllmf |= 0x10U; + } + + if (pllmf >= 15U) { + pllmf += 1U; + } else { + pllmf += 2U; + } + + SystemCoreClock = ck_src * pllmf; + + if (15U == pllmf) { + /* PLL source clock multiply by 6.5 */ + SystemCoreClock = ck_src * 6U + ck_src / 2U; + } + + break; + + /* IRC8M is selected as CK_SYS */ + default: + SystemCoreClock = IRC8M_VALUE; + break; + } +} + +/** + * \brief Function to Initialize the system. + * \details + * Initializes the microcontroller system. Typically, this function configures the + * oscillator (PLL) that is part of the microcontroller device. For systems + * with a variable clock speed, it updates the variable \ref SystemCoreClock. + * SystemInit is called from the file startup_device. + */ +void SystemInit (void) +{ + /* ToDo: add code to initialize the system + * Warn: do not use global variables because this function is called before + * reaching pre-main. RW section maybe overwritten afterwards. + */ + /* reset the RCC clock configuration to the default reset state */ + /* enable IRC8M */ + RCU_CTL |= RCU_CTL_IRC8MEN; + + /* reset SCS, AHBPSC, APB1PSC, APB2PSC, ADCPSC, CKOUT0SEL bits */ + RCU_CFG0 &= ~(RCU_CFG0_SCS | RCU_CFG0_AHBPSC | RCU_CFG0_APB1PSC | RCU_CFG0_APB2PSC | + RCU_CFG0_ADCPSC | RCU_CFG0_ADCPSC_2 | RCU_CFG0_CKOUT0SEL); + + /* reset HXTALEN, CKMEN, PLLEN bits */ + RCU_CTL &= ~(RCU_CTL_HXTALEN | RCU_CTL_CKMEN | RCU_CTL_PLLEN); + + /* Reset HXTALBPS bit */ + RCU_CTL &= ~(RCU_CTL_HXTALBPS); + + /* reset PLLSEL, PREDV0_LSB, PLLMF, USBFSPSC bits */ + + RCU_CFG0 &= ~(RCU_CFG0_PLLSEL | RCU_CFG0_PREDV0_LSB | RCU_CFG0_PLLMF | + RCU_CFG0_USBFSPSC | RCU_CFG0_PLLMF_4); + RCU_CFG1 = 0x00000000U; + + /* Reset HXTALEN, CKMEN, PLLEN, PLL1EN and PLL2EN bits */ + RCU_CTL &= ~(RCU_CTL_PLLEN | RCU_CTL_PLL1EN | RCU_CTL_PLL2EN | RCU_CTL_CKMEN | RCU_CTL_HXTALEN); + /* disable all interrupts */ + RCU_INT = 0x00FF0000U; + + /* Configure the System clock source, PLL Multiplier, AHB/APBx prescalers and Flash settings */ + system_clock_config(); +} + +/** + * \defgroup NMSIS_Core_IntExcNMI_Handling Interrupt and Exception and NMI Handling + * \brief Functions for interrupt, exception and nmi handle available in system_.c. + * \details + * Nuclei provide a template for interrupt, exception and NMI handling. Silicon Vendor could adapat according + * to their requirement. Silicon vendor could implement interface for different exception code and + * replace current implementation. + * + * @{ + */ +/** \brief Max exception handler number, don't include the NMI(0xFFF) one */ +#define MAX_SYSTEM_EXCEPTION_NUM 12 +/** + * \brief Store the exception handlers for each exception ID + * \note + * - This SystemExceptionHandlers are used to store all the handlers for all + * the exception codes Nuclei N/NX core provided. + * - Exception code 0 - 11, totally 12 exceptions are mapped to SystemExceptionHandlers[0:11] + * - Exception for NMI is also re-routed to exception handling(exception code 0xFFF) in startup code configuration, the handler itself is mapped to SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM] + */ +static unsigned long SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM+1]; + +/** + * \brief Exception Handler Function Typedef + * \note + * This typedef is only used internal in this system_gd32vf103.c file. + * It is used to do type conversion for registered exception handler before calling it. + */ +typedef void (*EXC_HANDLER) (unsigned long mcause, unsigned long sp); + +/** + * \brief System Default Exception Handler + * \details + * This function provided a default exception and NMI handling code for all exception ids. + * By default, It will just print some information for debug, Vendor can customize it according to its requirements. + */ +static void system_default_exception_handler(unsigned long mcause, unsigned long sp) +{ + /* TODO: Uncomment this if you have implement printf function */ + printf("MCAUSE: 0x%lx\r\n", mcause); + printf("MEPC : 0x%lx\r\n", __RV_CSR_READ(CSR_MEPC)); + printf("MTVAL : 0x%lx\r\n", __RV_CSR_READ(CSR_MBADADDR)); + while(1); +} + +/** + * \brief Initialize all the default core exception handlers + * \details + * The core exception handler for each exception id will be initialized to \ref system_default_exception_handler. + * \note + * Called in \ref _init function, used to initialize default exception handlers for all exception IDs + */ +static void Exception_Init(void) +{ + for (int i = 0; i < MAX_SYSTEM_EXCEPTION_NUM+1; i++) { + SystemExceptionHandlers[i] = (unsigned long)system_default_exception_handler; + } +} + +/** + * \brief Register an exception handler for exception code EXCn + * \details + * * For EXCn < \ref MAX_SYSTEM_EXCEPTION_NUM, it will be registered into SystemExceptionHandlers[EXCn-1]. + * * For EXCn == NMI_EXCn, it will be registered into SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM]. + * \param EXCn See \ref EXCn_Type + * \param exc_handler The exception handler for this exception code EXCn + */ +void Exception_Register_EXC(uint32_t EXCn, unsigned long exc_handler) +{ + if ((EXCn < MAX_SYSTEM_EXCEPTION_NUM) && (EXCn >= 0)) { + SystemExceptionHandlers[EXCn] = exc_handler; + } else if (EXCn == NMI_EXCn) { + SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM] = exc_handler; + } +} + +/** + * \brief Get current exception handler for exception code EXCn + * \details + * * For EXCn < \ref MAX_SYSTEM_EXCEPTION_NUM, it will return SystemExceptionHandlers[EXCn-1]. + * * For EXCn == NMI_EXCn, it will return SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM]. + * \param EXCn See \ref EXCn_Type + * \return Current exception handler for exception code EXCn, if not found, return 0. + */ +unsigned long Exception_Get_EXC(uint32_t EXCn) +{ + if ((EXCn < MAX_SYSTEM_EXCEPTION_NUM) && (EXCn >= 0)) { + return SystemExceptionHandlers[EXCn]; + } else if (EXCn == NMI_EXCn) { + return SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM]; + } else { + return 0; + } +} + +/** + * \brief Common NMI and Exception handler entry + * \details + * This function provided a command entry for NMI and exception. Silicon Vendor could modify + * this template implementation according to requirement. + * \remarks + * - RISCV provided common entry for all types of exception. This is proposed code template + * for exception entry function, Silicon Vendor could modify the implementation. + * - For the core_exception_handler template, we provided exception register function \ref Exception_Register_EXC + * which can help developer to register your exception handler for specific exception number. + */ +uint32_t core_exception_handler(unsigned long mcause, unsigned long sp) +{ + uint32_t EXCn = (uint32_t)(mcause & 0X00000fff); + EXC_HANDLER exc_handler; + + PRINTK("----------------All Task infomation ------------\r\n"); + HalDisplayTaskInfo(); + PRINTK("---------------exc handler infomation -----------\r\n"); + + if ((EXCn < MAX_SYSTEM_EXCEPTION_NUM) && (EXCn >= 0)) { + exc_handler = (EXC_HANDLER)SystemExceptionHandlers[EXCn]; + } else if (EXCn == NMI_EXCn) { + exc_handler = (EXC_HANDLER)SystemExceptionHandlers[MAX_SYSTEM_EXCEPTION_NUM]; + } else { + exc_handler = (EXC_HANDLER)system_default_exception_handler; + } + if (exc_handler != NULL) { + exc_handler(mcause, sp); + } + return 0; +} +/** @} */ /* End of Doxygen Group NMSIS_Core_ExceptionAndNMI */ + +void SystemBannerPrint(void) +{ +#if defined(NUCLEI_BANNER) && (NUCLEI_BANNER == 1) +#ifndef DOWNLOAD_MODE +#error DOWNLOAD_MODE is not defined via build system, please check! +#endif + const char* download_modes[] = {"FLASHXIP", "FLASH", "ILM", "DDR"}; + printf("Nuclei SDK Build Time: %s, %s\r\n", __DATE__, __TIME__); + printf("Download Mode: %s\r\n", download_modes[DOWNLOAD_MODE]); + printf("CPU Frequency %d Hz\r\n", SystemCoreClock); +#endif +} + +/** + * \brief initialize eclic config + * \details + * Eclic need initialize after boot up, Vendor could also change the initialization + * configuration. + */ +void ECLIC_Init(void) +{ + /* TODO: Add your own initialization code here. This function will be called by main */ + ECLIC_SetMth(0); + ECLIC_SetCfgNlbits(__ECLIC_INTCTLBITS); +} + +/** + * \brief Initialize a specific IRQ and register the handler + * \details + * This function set vector mode, trigger mode and polarity, interrupt level and priority, + * assign handler for specific IRQn. + * \param [in] IRQn NMI interrupt handler address + * \param [in] shv \ref ECLIC_NON_VECTOR_INTERRUPT means non-vector mode, and \ref ECLIC_VECTOR_INTERRUPT is vector mode + * \param [in] trig_mode see \ref ECLIC_TRIGGER_Type + * \param [in] lvl interupt level + * \param [in] priority interrupt priority + * \param [in] handler interrupt handler, if NULL, handler will not be installed + * \return -1 means invalid input parameter. 0 means successful. + * \remarks + * - This function use to configure specific eclic interrupt and register its interrupt handler and enable its interrupt. + * - If the vector table is placed in read-only section(FLASHXIP mode), handler could not be installed + */ +int32_t ECLIC_Register_IRQ(IRQn_Type IRQn, uint8_t shv, ECLIC_TRIGGER_Type trig_mode, uint8_t lvl, uint8_t priority, void *handler) +{ + if ((IRQn > SOC_INT_MAX) || (shv > ECLIC_VECTOR_INTERRUPT) \ + || (trig_mode > ECLIC_NEGTIVE_EDGE_TRIGGER )) { + return -1; + } + + /* set interrupt vector mode */ + ECLIC_SetShvIRQ(IRQn, shv); + /* set interrupt trigger mode and polarity */ + ECLIC_SetTrigIRQ(IRQn, trig_mode); + /* set interrupt level */ + ECLIC_SetLevelIRQ(IRQn, lvl); + /* set interrupt priority */ + ECLIC_SetPriorityIRQ(IRQn, priority); + if (handler != NULL) { + /* set interrupt handler entry to vector table */ + ECLIC_SetVector(IRQn, (rv_csr_t)handler); + } + /* enable interrupt */ + ECLIC_EnableIRQ(IRQn); + return 0; +} +/** @} */ /* End of Doxygen Group NMSIS_Core_ExceptionAndNMI */ + +/** + * \brief early init function before main + * \details + * This function is executed right before main function. + * For RISC-V gnu toolchain, _init function might not be called + * by __libc_init_array function, so we defined a new function + * to do initialization + */ +void _premain_init(void) +{ + /* TODO: Add your own initialization code here, called before main */ + SystemCoreClock = get_cpu_freq(); + /* configure USART */ + gd_com_init(SOC_DEBUG_UART); + /* Display banner after UART initialized */ + SystemBannerPrint(); + /* Initialize exception default handlers */ + Exception_Init(); + /* ECLIC initialization, mainly MTH and NLBIT */ + ECLIC_Init(); +} + +/** + * \brief finish function after main + * \param [in] status status code return from main + * \details + * This function is executed right after main function. + * For RISC-V gnu toolchain, _fini function might not be called + * by __libc_fini_array function, so we defined a new function + * to do initialization + */ +void _postmain_fini(int status) +{ + /* TODO: Add your own finishing code here, called after main */ +} + +/** + * \brief _init function called in __libc_init_array() + * \details + * This `__libc_init_array()` function is called during startup code, + * user need to implement this function, otherwise when link it will + * error init.c:(.text.__libc_init_array+0x26): undefined reference to `_init' + * \note + * Please use \ref _premain_init function now + */ +void _init(void) +{ + /* Don't put any code here, please use _premain_init now */ +} + +/** + * \brief _fini function called in __libc_fini_array() + * \details + * This `__libc_fini_array()` function is called when exit main. + * user need to implement this function, otherwise when link it will + * error fini.c:(.text.__libc_fini_array+0x28): undefined reference to `_fini' + * \note + * Please use \ref _postmain_fini function now + */ +void _fini(void) +{ + /* Don't put any code here, please use _postmain_fini now */ +} + +/** @} */ /* End of Doxygen Group NMSIS_Core_SystemAndClock */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/main.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/main.c new file mode 100644 index 00000000..16c8fdf3 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/main.c @@ -0,0 +1,49 @@ +/** + ****************************************************************************** + * @file : main.c + * @brief : Main program body + ****************************************************************************** + * @attention + * + * Copyright (c) 2021 Nuclei Limited. All rights reserved. + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ +/* Includes ------------------------------------------------------------------*/ +#include +#include "nuclei_sdk_hal.h" +#include "task_sample.h" +#include "target_config.h" +void user_key_exti_config() +{ + /* enable the AF clock */ + rcu_periph_clock_enable(RCU_AF); + + /* connect EXTI line to key GPIO pin */ + gpio_exti_source_select(WAKEUP_KEY_EXTI_PORT_SOURCE, WAKEUP_KEY_EXTI_PIN_SOURCE); + + /* configure key EXTI line */ + exti_init(EXTI_0, EXTI_INTERRUPT, EXTI_TRIG_FALLING); + exti_interrupt_flag_clear(EXTI_0); +} +/** + * @brief The application entry point. + * @retval int + */ +int main(void) +{ + /* USER CODE BEGIN Init */ + gd_rvstar_key_init(WAKEUP_KEY_GPIO_PORT,KEY_MODE_EXTI); + user_key_exti_config(); + RunTaskSample(); + while (1) + { + } +} +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.c b/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.c new file mode 100644 index 00000000..631df971 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.c @@ -0,0 +1,121 @@ +/* + * Copyright (c) 2013-2019 Huawei Technologies Co., Ltd. All rights reserved. + * Copyright (c) 2020-2021 Huawei Device Co., Ltd. All rights reserved. + * Copyright (c) 2021 Nuclei Limited. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, this list of + * conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright notice, this list + * of conditions and the following disclaimer in the documentation and/or other materials + * provided with the distribution. + * + * 3. Neither the name of the copyright holder nor the names of its contributors may be used + * to endorse or promote products derived from this software without specific prior written + * permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, + * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR + * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR + * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, + * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, + * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; + * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, + * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR + * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF + * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * Description: Provide a task example. + */ + +#include "task_sample.h" +#include "nuclei_sdk_hal.h" +#include "los_config.h" +#include "los_debug.h" +#include "los_interrupt.h" +#include "los_arch_interrupt.h" +#include "los_task.h" +#include "los_tick.h" + +#ifdef __cplusplus +#if __cplusplus +extern "C" { +#endif /* __cpluscplus */ +#endif /* __cpluscplus */ + +UINT8 __attribute__ ((aligned (8))) g_memStart[OS_SYS_MEM_SIZE]; + +VOID TaskSampleEntry2(VOID) +{ + while (1) { + LOS_TaskDelay(10000); /* 10 Seconds */ + printf("TaskSampleEntry2 running...\n"); + } +} + +VOID TaskSampleEntry1(VOID) +{ + while (1) { + LOS_TaskDelay(2000); /* 2 Seconds */ + printf("TaskSampleEntry1 running...\n"); + } +} + +VOID EXTI0_IRQHandler(VOID) +{ + if (RESET != exti_interrupt_flag_get(WAKEUP_KEY_PIN)){ + if(RESET == gd_rvstar_key_state_get(KEY_WAKEUP)){ + HalDisplayTaskInfo(); + } + } + exti_interrupt_flag_clear(WAKEUP_KEY_PIN); +} + +VOID TaskSample(VOID) +{ + UINT32 uwRet; + UINT32 taskID1; + UINT32 taskID2; + TSK_INIT_PARAM_S stTask = {0}; + + stTask.pfnTaskEntry = (TSK_ENTRY_FUNC)TaskSampleEntry1; + stTask.uwStackSize = 0x0800; + stTask.pcName = "TaskSampleEntry1"; + stTask.usTaskPrio = 6; /* Os task priority is 6 */ + uwRet = LOS_TaskCreate(&taskID1, &stTask); + if (uwRet != LOS_OK) { + printf("Task1 create failed\n"); + } + + stTask.pfnTaskEntry = (TSK_ENTRY_FUNC)TaskSampleEntry2; + stTask.uwStackSize = 0x0800; + stTask.pcName = "TaskSampleEntry2"; + stTask.usTaskPrio = 7; /* Os task priority is 7 */ + uwRet = LOS_TaskCreate(&taskID2, &stTask); + if (uwRet != LOS_OK) { + printf("Task2 create failed\n"); + } + + HalHwiInit(); + HalHwiCreate(EXTI0_IRQn,9,ECLIC_NON_VECTOR_INTERRUPT,EXTI0_IRQHandler,ECLIC_LEVEL_TRIGGER); +} + +VOID RunTaskSample(VOID) +{ + UINT32 ret; + ret = LOS_KernelInit(); + if (ret == LOS_OK) { + TaskSample(); + LOS_Start(); + } +} + +#ifdef __cplusplus +#if __cplusplus +} +#endif /* __cpluscplus */ +#endif /* __cpluscplus */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.h b/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.h new file mode 100644 index 00000000..adcb79b5 --- /dev/null +++ b/targets/riscv_nuclei_gd32vf103_soc_gcc/Src/task_sample.h @@ -0,0 +1,54 @@ +/* + * Copyright (c) 2013-2019 Huawei Technologies Co., Ltd. All rights reserved. + * Copyright (c) 2020-2021 Huawei Device Co., Ltd. All rights reserved. + * Copyright (c) 2021 Nuclei Limited. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, this list of + * conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright notice, this list + * of conditions and the following disclaimer in the documentation and/or other materials + * provided with the distribution. + * + * 3. Neither the name of the copyright holder nor the names of its contributors may be used + * to endorse or promote products derived from this software without specific prior written + * permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, + * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR + * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR + * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, + * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, + * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; + * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, + * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR + * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF + * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE + * + * Description: Provide a task example. + */ + +#ifndef _TASKSAMPLE_H +#define _TASKSAMPLE_H + +#include "los_compiler.h" + +#ifdef __cplusplus +#if __cplusplus +extern "C" { +#endif /* __cpluscplus */ +#endif /* __cpluscplus */ + +VOID RunTaskSample(VOID); + +#ifdef __cplusplus +#if __cplusplus +} +#endif /* __cpluscplus */ +#endif /* __cpluscplus */ + +#endif /* _TASKSAMPLE_H */ diff --git a/targets/riscv_nuclei_gd32vf103_soc_gcc/doc/image/nuclei_tools_download_linux.png b/targets/riscv_nuclei_gd32vf103_soc_gcc/doc/image/nuclei_tools_download_linux.png new file mode 100644 index 0000000000000000000000000000000000000000..18eac2878a8d3d5c5da6f74463c5a4f191378989 GIT binary patch literal 41868 zcmdSAXIPWZ^Dm4AvGWyF6e$)2>C!u>fQa-iAmK~zASJXAVnalv_ZpDi5_(T!p-At9 z-g`nqO9BZbC;Wc@b3M=7bKaf%x`2CTXLo03cK4p0{ScwAt8wiz`(*|OhHILy)C?II z7;6|9&P-msKTbk-9ni*y?2 zD*(6byPrv|bdNssxy;ibXj=ZtN1^|0RlxnV>uvKNPQ5tC_O?xP znVB5(dh~)sYu*iA9Ua1n+Cf_2w7KG028Q=54)K#8e%ui4L|;nim405UY0LVG-rdix z^K-l<9v{6Db?*mxgt7$Cd5L--T(_V3Olv7ZdwCFR;32oM?mu31d*7eazRKRC z*}0tEE8D=yp%Q=X&~ zJC|8AUbe_9cy?jmU=`^MeT%O6^M&uu(_aCs+jpcq|935uADyLL<07ZiuIpD@@sPU$ zXNrCOq)llxeRVFF@S5tZG+902pcC)S)Fn)#w8S$OPNxMRrC6*?^EaQ*L$1@R!s)xN zy$O>MfYsAEx%aEBJR(r~!L~ZRYymj*&D<`#m-j!mRg3#tCAfR)$5s&wF}E-*7Mq$3 z#ZEWC-(HviL8c4mtGBP27!#)I{9ctJ?pA@xz#iSz*(d?bpuChx``l||oShwK)>ioD z*R6JC*{_jx!MNt!^xDa}(YUSsgS_Ud2!uHcR54dqPpC>JpNy!W;8Se8+6|+}!ICdY zsMfa%6*R3V>ak2z>)ym?8tpv8S6E`=O%vGL$+(u;j(Eq_9N(@ts*OUgsMVuG9t_RFMd=>LliNp(K(TEgs&;UW%z{m zS2es)Cm)AjK0*9de_+EQrJ2~Yb8NF6m6*2S`mLi zZ^V{@bKxz*#Bhu2L2B9P?>V6=?5*@Ye2SFFegJ<(wn*cqBSESC?t1bdPS~Pln;Dc> z8vVC8@5zkY@9sI|^9=t<8k4}dG2*~NV4JouYdJ1}|HrbFD=t@l_2~XNhJPNHl$0O~ zByFc0+jy#!rURa?GoO&BMcgKfA47G~cBJ_{fQ*h|VV8?@jktvM$(!hJvW%fY=IK^(-2yF%c8oX4Ai&NY*H=kDJgL`KHxlQFfZL;E5G zqnb0?v&njQa?0uua)#lV+{)&m)c5M`6eZP9AgeOn=+)M6rzd!Yoyr%XMKm>sDKt+8 z&)Zwt({bdp0L7hP3NdRBxLv{#oFz%3%xER<N zkVCJ$wVEczwmyd&=5aNzT?Nti%5b#^8$@d0eA5D_l7vSB!UVZJv;1URiaJrIM08!L zt~=h2+Zw@(DeeC9shGG`SfH(2FD;w_cM4a|S5}=z@8$QWdJeDKeJLjO*%5|kq^1ru zQU~r%f@+s~(%3^uoMcSuk$Omzt=O#tTC*10jM8&fgd6 z=%L+7wKn+ak<=_`np2+Um3QDNmVjko;7M?9gRcsufm<(p=PW^QuQokkEB>>HQ;lu$ zE99-Hmw8zI3f_t`@7GB8IqYiQuY$Od6TQ?$WA$io=KFoqi_>i9Myl^r&gfR11C_vY*Yg-zZ`RCEhJH$*j5R4=L+}W?H`z zM`Fj6Ff6kkN=~o>Jzq{&YrIiS6YLVAuP>!oi<1(pW}uTLv7(8fRTG*)LA8a-ppx{V zQci|{UjE>zK{P=@lB8Ai!H_?whQrMp2OV9ld{${--Y2s4Lzif3UtJf7{nWf!P%y=1 z;PEQD9wKEfGplS6nIN8v&@|!>eFK5U7a)j_!={TIjIz;$uq@$97i4zxi9u8*Nvq^? z!o#|NKj`2k97yu;)1Hw!GsCmu;f_lBGz8&q_Pv&`?Y~j#CfYX*C|;x?)%YgRWRJ0Q zDWWTnspyEInIy25Orw})L0av8bkwGof{yPt@BY$|T*Z5AUpY6vg^CH|0UNn)>XD*H z6WMShoM!%};mdtguDt8(e&g1j&3f=wLT0uc?INY4eXteL?^Dm-WtBUCy2^bQ53PA- zEl=bxINIFu`HC>ee-~2%3%4AbGzP)lW z$X_J@T;`NbtDSIC;LQr2J@}~=&3isdhdcUFkVE-d zpo5!K$rj9XqGKJm)%V9!GsPN zVqUtax5Y?}<;DP~sl>e$7}>XsT$&6Iw2fI)Cgo>S;{BuO#arlT+#)naD;g5^0d!g9g^l{Bqo z9mPVV;)k!P0><6c=OEGbp(-YND<`l?c!Lzg^0^*P`GmYI6AZ>eBqxqYWM;HVXJ~1= z4aBPnaF=e78B zkAFYN$ZjpR+{i+>z{&mz!e6Y2rpki%f{O=~3}p zZF;z8(^5}$gp>12g1t*^-He&jl#clj#|zUpba~S9^pwdR!1TAT_peA5Yw3Ul$oIYJ4xdH6j&g~wBK%7OT#Tn1FVByq5;7*xQmx|KKaz*@(h}> zdmz8g;!U#iW=HG%Kn4S0PGM}naM$9n>_o8LaN>maV>QxobCOSa*n&P}&cW&w?!j9m zBrfBbRHHS1b1w7~VdmRl+rfn>#O6z@cW4QArK2l-Kq{jA7TI|(aCQdoKbzteKUhKb zq(1EHvrOJ}qOe1CdN|O+!)#@tHAF$#Dz~}iBirULvpz*%dUNL=Fyy!giEIK;F!4Q~ zuOP|orWDDt#v?3zZd~7^88om(>YE5!&3kz=QbS?7RS#i<;352yMODpnCS(dk9s+musu(Mk*|0 zG3ZrQ{7BXVYgy+pr(l{Eh?C*H&*yHeVb@S~6@1gkX{~PjZgX)If-BW)FC)eE+VU()Jd~>eEEE1>;V8A*>Y@bWA7bhtr7It66rCGs|p@PR^cX;MyAe11Z? zK2$uQ%8R@jB*ZPc4<(q?a+2+-;$~M3PrlaxHH|=zGHXZ1S~ToHf4oR$Y2@F4hL5i+ ztX3vc2F9Ix3hxH*G>1zbjxmzSe3V`HTH>T)Himn=tum_N6RY8MDE1JsZJE^cPWMBC zzNh)x@wAHbHe5?`Tt52*3QfR!%^x=yJWxWjx#AQ9MiLzn!NtBd?KndJ$Pwp$x-waa z;uv?<8e|V4*C_-2g*26PAx*g%wgJCAl?WU=PIcbk!l@E`=o?4)IR^dEK>4(7rD?+U zfqD9p<=l`8(;SSNkd+`~Y7%}=#8e9;C=LW3_05hxJ$SW-9bIAu4A!MkbXeKk5C zEg8bISHBw!vu-~+ zUnW}*T!&Z1m3EJv`!e_93sK~9!hTQ`@~1%^v<2XWFv`>`@l?m5qv4WK?)1;})gZCW zxypfC%`-zwHv6My%X9Z+LAzzmL4!Pf6aN&{|LgCyDq|{#6Rk*(E?(R)$;v8_;R0LO zNo;Q$9+{@W0vo@{*DI9$4V{kCRo2zP0-;Kn+8;kpCd<*>!B)^?i)Rc7H+mG&c3${m z(3UngUcrjhu&{K>Mv4QRdy=3(XYM?JQ#m+F6$_pWQsgAk$aR1aa2&$n$h!dPJ8NzS z+}a4vw*e||29lgo9WVz71i78mGrQ}C85tFPI|h;*qbA5_xx=ST;es3G^sGZXTNl=L zGKU!&Wc~=;(?WKR%A1lRJh3|5xp+;b>=02b$T_XC%!RL5llslkKLeiHIl>_8nU1EO zVW+lViL+~z8ax6?ePPd>wa}n{q`a&}{ESm!gGJWz{VwIhh7g~We{PC=?5uSgV=+?* zA6#vT{gM1mfD;t)C3Ag)h6wt?b*DjokH`Jt;R!23e4QEeN7gVUnj<${w3=^FGT|H5 zw-_hizB|Or^MSIRA+aKq2={qy9R(?eHy`od(lNtCQcF|50DbGSCr>8*z;_IQ{?Uao z&<9SqnHgFct;tA+SV^if@XbQwbrIBq$K91)33^Fu&6xRyt-XX{Fzd%`m6exSczGq8 z8dF%U8JK-zst7vTs1RHVJh!eEoiw)er3YA_chQN$ta4is1UA^)MkBT`!NU0A!YEDB zwaX0mKLl2PRIDf<6Y=G|L5s`R5lTd0nDAayL;*Vut6{Nr3_@zMilQGq3U@u;01;l% zU|SRShYh3Lg#*1ac~=Ogx+V$PGS0sR^9bW*1DHSIE$6x2`d=c%H~+kdZ@fYFP8e@| z@m&?D<^igEY8tYRTXz@8-X05)b|c7_5M5@E6ZoQA4FZU+56$d;dhAOrDrr;$M<~Je z-}7Puq8yuDR*cf+7hQC~+YijtRJ7}0&YJ|^WbJfznad?7RG<@}PL_dT zm9YzJSXO?ZGXEoB{1=XiM8X?}0bhhlo2Frd%p#L)Q22+C;jw}NVMh2utG(zwSM@=g=>_%$*0TXLx* znusol4t%#vp$$bIkp=lGMI~lEgwg}Xq&mMS-<2Y)_e@!Edw;BlP%6d`$H%uKy|Vgl zyA@*`vi9n#O8l^l&9zMkn-$pL$FCOhp#_ukveRHmeP~Aic-$gDw4{X5jMN~j3Q?w? z&gD!!EN>INADWm9A4BYEIL@h7&l2TqWi1+bJQ%?oq;(}rUAZNoC+PgQ$Md0MV|R-< zJmD0Nzdkb0=xIMgi!v=gkf=s%G9iMCG9SNGcaJ|8>oP*HNJiKgyTKH)gJ1n26ZBhH z#S`PaTc-%kum5Comm@o;8u)vOF@&|N8t-OmTP`rmK7zx22u4)BlNLr5RVJ!{P z*Vi?61~dkT4O>o>wO5<9WK~GMFjm=SiMktH0NHC}o!U62lAPb^IpwG3wMQa*wE7_@ z{Y7MX(NWkB90XyN0{xfmY#MU*TySw6q^DYSAH{!oQ+mGvN~VNS*H;p=gBOrES4Zph z8oQSI3(?2cb`Gz^=&J+SI)kVLqcw#}1Zf^+~ zSE5^&^f}SEn?QGfhRGh+k+K8$>1(vouE}QE6GOMM*`$Ci0{!F{*3y67s3fb5;Dsm+ zIA;O}y7oxvMTU-bTr7=OJ;}U_{5{!V?^)-yYHT(;;5Y8!KKAj5N*=qmFTt5q@3OU1 zH1g0(%ytE&4LT@u`>0d$awK`nIhzS22g}#_ZIrR$^@+ozy(xo0w)5&SX}ibBbX}IU zejHlyrW706W(xC0-Pz)v7Yf1e25bB^$P+oK?#rHds^#|9p(|=kz@0g3s}%BCA}F)0 zFXQ3HW}_!!T#mUft`GR7rcL1m;aP%??P`kx^xSVapYM+lgjU%GXyXYuJQ= zkCij5-c^ZQRLHYVAAZQ+e&QH*Th8?{J68&9w9c(=yvkT%)La^2Vs7B|snz5jq}D95 z!12MYS*fv;8Q&MdYDFa;oklYeO9aam(J1pm{A~plVa^J>40j*S@Vb^#%qxw`W@XI! zS=3M2I;+3)p24lU!1g$lv)%LAC22<6*(G`7y4ixMAZd^Nl#gv$w>mZUvgp@pUHP?Q z?s7f7lEaTbc@0%+a1SLqi5m5^`k!x_l3tgaed|2tCzfwI;+;hy3)T&IAM8l^q_}kO z`SbsLa4l)Ed(y#euG6}`z~rTKSsZi?QqpHSc(@s&QQ(r4Fj^;@V8edIH6jA0rYW#g zOmEU8dli|9h8ycxIo2X;T*$`I**Ka$tLli-K8L-oa#{y;bBM%I>V?9F-$LcVpb z-6qdky`Y(Wnh(7LD^#&kD6Gm%5#URb?=zVEAw5Z5Yi8%t$)~qb`T+0ps{AyYuWsgpEVQgZMk)VhRAoj5d-U3?7Zmt?NalA#NXW|>7S#(i zH~83yqnoDB!=PmD(~M)?)yx&`&z>fxE(5O>rE9JJUiX-@h2M6Z)op6|W^C4X7ITih z%)C(+W&UbxKl&#awqN)768U+aYP9P78QO^CI=^>DJ%5ODGyQNgcGcLp{o~oLyy$m$ zqki}lyQWw4Hp(Rfv1JE-S+=N!Lz`{K^3c{i7B9d5;Sru(;V1L643O9S@JN@D;l2IR zrhR?NIqd6ACBlw%hF~g5++^fI!g^A2$td!O7^~beT<`IrQUIb5hOllm$C}>F@{~z9 zx>Y$7+6*rHhcIAh=H!kFu2QxxFK*Vg(o{OM81`eXs2w=d{Cgg~Q8iy87LO>PKS*7L*vX z_*}t%eWY4shsp03EUT1nHsY3;PXNzEu`G|VMuHX^^NS6f-&TB0H_Hbhox+!h4)8f` znW$g@6e;x@ugd{5_#}!>>(3UX-^RT!N@%+dm>;M$O>udj=h03DLN|6(?CuJ4#8N&t zC&s>c@;slj;Hp{D9zfV)EA^i$1_dM_Tjp1;UY(zm+#Dcg6bJTpVKNfRz2xt(Iqemx zT;%^N-T~JXl3v&Yk#*%qd{F2?fqpfRdB&MTMx4^u(#Sv}N-_5RC3!&lO+Hl0`e%xFDVtf(QG;AIxK5+hxIK1&&hxRKFi4~<4+FWrEF zB%_ns+pb>l^_0AGi?;ja*0b%G2K8k-_=(rwtmd7$-SpjM-KKPj z73@$0T(L0a?flQ8lAy>|RuPku)%Gojg$byq9+Z}i-1N7iv?-7eTZBC3s{2sKhfx4- zN+YcG@a61rHYUG`r36IW^dBDiJ9Z4`P_V#A629`}-qqcYl&Y+th^>02=AKEJFL(eC z$t$qLE+-;JNU6xE-{#;X3n~<+EVv?jd+EDM*4FiZWh^Nqv;jTJ41|wt<&K_&^B9)`nMAf5q@e z9x2OS+eT}V+#75`JR8|5hF3n`VePcx~_qMuiDg9 zWE>oAT*5_&Ry+zFYI3?Y{M)t;Nl~O_flrPe%H1QHxEc@4#pI0+PI?7<)w^c?L)~2$ zwz62u2yC@?Eir2t$4w}?MQ4Y2haMh^gTm&jl{NZ+*`seNl0>%dhS(1GJD1^L5urY{ z!FzYEg@V*`FKy3a&}=k6Y|NvKX6Ep!GEc(+Dtybb z^GZ3{#cXp;`d4*YGuts##8;WQC1qm>HB;;hMnNL`TMqqarNA}7f%?SeX6#z_4b!3g zt@3-IvVwh={v&hzRfLgJAMFf?y9IE}d<_(kmMMHwOUVA?(7ZCW0oJ_ka*c~vi(?Ng z^2}z52@R)zm{Oi}Vbx0R>$&;XdCIq>BTPQKy1?>Rsc;pb4oB0`zKrD2^v8jJ-62~M zu=#n!g3heMnr}sb!;=6^c+4ES{1sUwz#Zlv{cU9ysyE^b4Ht~-ACK-GsJkCe`K~sy z56sF_kF46C?rPp_USyYA)jIiCues5gc#od#VLBj{;O6FlAV4`%7#med+!~SL{d=VE zFG_~K)bTBJH3D{P7ENB-b#(PjuhE+iMu@@QuaI$4>4c`T^rF$>exw?@&L{cHx-(&P zeT+oE)=lX=!^HLQ^b#pD@c zD^=!E;CD3aM7L%xv-p<`0nJFuH2Q1a+BCJFaiS2ZJVG%l+=S>U6>Gt3Z5Q<*-byM` zdPw~MV#MzTI!J)$zMh$5M%I34Y!?0a16b7kh_fmk8t4`E-t(YkTakf!srOrg?Phmk zXd_*)mw%G~SZv^mm^MW_UjocIILF3LdjIwCAGDD#GvWuio@gi6bmR5x)ES74L69w0bT@I!V6!V*Pw zM0A8w{@l80=IRH_=9u|qb;d3`T!UPqdd;lEyakLxX(?n`f6wRmalK)-=w6I)2kW~x z0ZPXU=B{^q?tp1bzp-{DoWsxAno6m@wLzN?`?654uAq-aq*Sz&W=8htNh+a;8z}N) zUB;kvdFIv^O0E+bVJ@I@UEr#ajO%X|&oOnd*GM~T{cWVjafs2ADB#rQqbT+ z6bTOva0f9Tsg-4M+YAp3)3R8<3t7GmjBb|AR<-sy*`oMq%y|b|kY#@!Iq&0J_MH`Vk4=qHaL%Ory@7(c&`kOfO!U{Ee?K!prnM6sfJXVrklS0V)M%91jId+rA z7eKBb)w~vCQl^93D(Jy`@1up!hfiaJzj@Luwag$(r}u5vi{vZer6am2{#}DNTo}2# z6KntYy-h)~%TUi)S?T|Hy8XtAvSJhr+&Oa10MspP%_nxt|JW?q0ybk>8(GSRRu7JE zO#r92TF(m9M?S7Yif|G0=V$@eK(FA`(wlp(`v#GS^<&F_m z0h>P;b-3=yO->QU&led3W3+Cw!FWOHx{A2z0awo3va(p|X$!oL|tA9S9d z0oAS+X;)B9N|T0ObdJKxRWYM}k7rqXluw!+imDsnBfsku3Iu?DOP7Ggd1M>;AHfqs zZf}pWQS<%ykophqcb2T<9of$_9nVW%E z={v%8E%c@aH*BlUZ8P?cB4X{x;v|nCn+Wq4W(O@voo9Fzk|bba*#7O-wlKb@t7})- z!S2fiQn0%3ws1kf*oK%{$pY@S!od*g0tULzA$y$CWPhkNVDwoqWLV3K!`Qn%;F-IH_34EaUO7)l)QQabF=1b-}m=vtYZO# zz5licoS_`_-SgT?L!(BvRDN^dYhC5*J(y>GPJ&!-IXj7MYXaHpCgv(@5r#G4el;@R z9$8{g>7^;w*||+BVLVx2fwHwBVIV<@ZR7U{`)&O=gt6!Wcgdw7aGj;gVB~fZVN@_! zctnmVLQcA9Ga5xxpJo4oD#G5XIrt5kAEV5lusd3p&%;NIAvjRe1%Kr!q;@)ar;feq z=bXNkm6Gje&v%>)gC|!4G8jg9*RCNXU69DS?3oa#q|t~mzRiCtfKVX6{`qhJhRdvZDnP|dh9ozu%qs2&-7hm-*5?c|HUi4GR5WMLzSPjDSD-JE ziqTQyc|&$FJx6ZEK>hLg%2Ny?1OBy^mR9i=mJZ;PXA1w#_ur=nEW1&vnecFZPZzwCOs|WR12-6msJSv9Y z^hJ9Xf0w`E_!dm5Hc%0sEVh!`Dl=LBV@&vZRh^6(iba4wNpDZBO@x!>ALi+P_F($6 ztAbK!fT5SJp|l(h8W|W~nI;LEi2yU=Qu%7GvHqL!>>ho1I|8h4G8hzwQh(ntdUp0^ z`GP$iefLZ;_2UgASwo8gtuT$^+SO&c;Is0_uD$89tk3Dm^qkgjroHSbf6-X?hgq;o zr
  • w$h07o4Wa2^K{uK&>y#II)rVDk-_)%F~_==+rw>LuDEK{~w01=X~rLrt2Jo)Dz0KFug_&)}+*!pWgzQDm&da{Va5HDy~jb zVIRO{0#tj+Y0_}&CEND4N#42WJgfJNqv+x}zNlcUz{4T%5=_F@4uyr?aNpHipO|ro+@{LyxXm}D=n5T@|B6zw`2M0 zE4@V5^U81a<>&@@?<^ta7$ls1|J2sc%G)L8V6j1{oOzE7c( zb2B=hd7LN_t$h`8GHrob#}%{Csm z4)Cko*o`oWs=A0O7ll)8m!4MDM>O@6zH8g3%g0aA1uus4_;A%X2s^~q&&S>BI zYOZba^-^I^vjERs#wEA?ghM)3H77*eyFQ}foOeSCkGr^n@%<*wi>>E=$vmg0`=8lf z;wd@T<;MCfp*0%y%$@TI7d_|wY)`z(|9;SR-T8W>;s4^)+g|3pYcqek^p>u`0{DY% z+)tK9p}5N$uN>(v`p=^nGwJg`uMGdMBigSsytibZYHl~k8#`cJhbF=|||uJW3c-CV%o z(#>bysia$fTH&drl%M_&ZH~|BvvfVBs$cPVDYT};qo80($GPuUupK!5&ba#i<4tML zRPXlhqK=uD&Q}0_(bcGB0UoO!r=dRwDPd<@(4_R!xCSpiXUCu>@YFGN_s{o7{j%dd zcW4ZWraz(~Rr;`m$qzC&Yj$|g-XCw3Tzg7A^Odh7b5D5ZID^?Lq~y%~^xi|3!==$k zyx4aLeb2-!TMH#k+t&yE4pKd%f4e*Q_*6;LJCJVfcv*&}$2(kh9h{>79-sS16mXAb zTk)2+Mh8;5w|D;Bj)=tdwB0A!^u7b1n}3IV6*b~iV_|w`{&YFoW!=Ek+#_R%ZfZ?uPdU-qfR4YRwVq zKm`hz(Rbfm{xqmILqykittwq{3F?`hAAzSmA@dm)9`6dR(e+w*-1WBC)RPXdAI)ag zVrcFDu2&_0EAF)Yb{~5CyQ}9JM8%g4%OmAaH8oJ|KvnCD#80l>K& z>ri2cxPN<@d#OheV$5@PM?gZkeGB~Me_9a~Tz#0J-*%aI8l~K}Z#@M( zmPX1lE&vO|-G%6e-f4al1#u|&NO&LLe6=I9zB}W}`*_)R_s!hUwDO`3ZF=$u6Eg2O zE?-_KU$0^UX<9mKQen}Kbnv4?%gy=u)gkCZ&Tqx-}6fUDO?TTOJpO^gb0s^Oc61VG)b*Oop}3?r1ONp<s*Yx3*u9o3_hE9&vY6w*6vbW_Vq2HtZ2YcgcCK|EZVp z#TN39g_0(io)FVT>kPl9JWTlkqpe&5R>SZT{vJE^s_Ti z&U=DJ2|Ll1yFpIpKOoqmpp41!NI2u1*EuZ%_|Q+~4hs07ZP~=;z`g)U%~|IKUF9>N zyN%6Sp5c{o0T@bOxv|CZ5Bhbt?ER~xT;RIE3TOsoT!8jiM9>MG7v<=%FOzP=!u6nV zz})r(lrInL-?3)6pKJ0;b0|(@)O58w39FU=ZQQ}6)Ku&)CnbJ@e=|e7WIpq3*Dt<& zO5yhr_s%`Tya2n*!FtwqZ=Ljkkt+!euYr0d4ZKA4OC>_lRfg6bV8WIU3n}6y{`PIHa$!O3vdpS3MfO>g_YG{*;cVWfmjD zw(UNqlPd|Sz01{X^I}4;7J@2M;<=W8?%#TI`6MH`b((LoO5<1eUZhc8K3?iOB;qk_ z*?Qs5n((KC7lq&~BjmLC6+7#u_~K=#S!}O=mwv-_4GWc&jfAJ%pUo;Hx}qPMSXnsp+$K^%5ymyE5V|de;$5j{c}NzU$_ zbz|1fL`RSkK-oO!XgtQ>j4&id)nYL+=V(zRvYj2rti_2C)wgmqaL)W5*)X->1sUG|r=VT5bOv?sTP|J)*6>?*e{;_;$~B2d;NL9Vip_{lS&>*3rxM$s>o8 z_RSCHn6PzAHpf~wy}4-GAA=M9^cK9#dvfYCq-^w^&w{^PU`{W2dG1p~hSHBR@!PFG zbP<>D^2Hg`KY{z-@^u_jM#Z8qN1^>tR*Ok#J!r_|G5ovIUXAS#G*kS=qPo76<1?{u zh}a|59@FxnY3`68o7@8+bmsL zfD@FlZZnSw`cX3KQ6j>~^X$flF-*myyDyjXjOWQ!{yIBTo68mGH?zKeswL44C#_lj zA3VR;riT)Eu4T8H5J1p8f1>(d_;EDk2`nDGIHb^rhMK{6N z6p4{>_DCi?LPWEt_i;7Q1LkFll#Jz*zqOm`|8h1&pYt-)qdfG*UN9f{Gu1U>rO9e^ zw5dn_K6p(Sdqr3&ys;rtoUj;|o&#f7YTuO^dn@zZ+p|Rn401dq-QX$MGnf5+$QH26 zMYDKYuxkg4-(OP_-P-Em?z7q`Z}!Yle$?TTx*vIIzvY~zxnLy0wN?rTeb>X59L8`hkxuf+R1Of4 z{(a?If98-|hGw$ico5<(VW6IspEUchi{ml zY=5@3%ox2?yn^se>eWPah=CD_;~Hk2a_8$=9`Yd*-fiM1v^$tDc_mSju%| zm|gGpTNPm=-wN)#9=hI-FY7n5Ko{ZWlZ*Y#a|MEp%U^=a>jvf7Eg6}{XgHP*u z+ht>Yc2T{rK{*g*KkrFQtS7gGu;&x=$%ag}ZmQtW(i4RM9 zLMtdmEw|nYFSGQF&z-;oOcQzCKh5Zw&&5~oc%P5d1GTcI5qY8|3F%w9e8_O7XIE{k^7Upzy) zsNkASH(y&%Hh18X7WT`5hI9jZCHDb1tuIy9ID!2F?vK#;;a!n5x6;pfvgi*%is*`# z`-cHK8Bu4WHM|pv6G^EqX%1YUlASXj9U*F#;SZR6eU;#iKL_6lBz371&6A>Jrp_-H zLCHku9pVA){UEX|x9AfS4GI1re7yPre05HvDp;F|+`KluewQ6P(QsQMEkCLj=M>=M zesY1ftIf<~9MUD;xhtI8x-Pb4dU2c@Z6Q>LF#Iz$!S-M?3H|#<2kQNB6eOtO+O`;H zpf=Gif^^7cx^}ywCe&Wid13x#lg8pJKOUfXOTJ#TiupD+5@9N_mIlb7w&BFG^azB$ z>%5Td(8)MmE=O=>0FhCt2(EJGhP#!mS!|loiM3DY4lYOIY}Yr%wNI^@@51NCo9A;? z$2!?j>nb*US=*)iQJ7x2*U~LZtw>-?)IRbe@29g$_BvzJTbk@nEOQTpjr;GihpAm! zFsO6mEaig88#&c0sfTk~NQgGslHYIwFi#2ifVAj-=YJB^q79~GQsR%1UV!%(QHc_J zET8ohIzIA(CCeM6zJwBNsrj~XcGeFAcW2A7BPuJ?(Fqs%ft*9Sqf{d)8(nz|v}M+wK$7^U8Mfc>)-Va@I)HE!C1xA1XS z`XI6rx$+Tzlf3p?26|Le|5t`HN-xK{{LzvA{Sl~N{y5;yoqM?PvCXyWSo?397p|q3 z)Oo;r@2NU6Cvr)pOv+r^@cT&(Z9I_0nQ#NWE6RbP_KNA?OF<8vFD=syRbBmzuf}if zeD_hHs+${fC&il*4->|sd7dvw9=u%3>a>OGW~JP`{+4^uW#mXV^171JG!j*L(r~Wf z+7oR3xbQ5i#gxf<^lg6RxBccK*9jBeyEn^UlFWXDAH-f$0&~3bF)7R6Y^Gre1GUA z%jcYjKl+ctG9Mq{*I7SBaQ~S#TTm+ad%~~g5^W`Un6R!T8M2|M!|e+Bu=Uz-`qr?X zdwg2#5be2rF}YkuSns2U_Ay@gwslL)f^U#E>I_oU`qQQT-$$sxs?R*519yWF_`0VM z+Z;nkHco2W>;;wUTk_v!?$&bKnhfcWvO!zZs_;#)WouQD)S zuBavmNgR*;+_aLKN>l5@m~Yt&T-^Tb<}5n;fY*ShkJEwA3VUhptx1Z1yY)-wx`J8h zoaN2&`36hh&&tSb)yp_BkJ=41nns$h5){~`bZyMaN ziAjo+IWj*JQTfBZZ}k0hOFwmh?bd5dV=Cpkrf!&~K<@Dq4Bht^mZ5q#J5brGy^Xd} zdS26GlZ#|K%Oz!Mn&{=d_(k|D$N0`zJGNv3=v*&P~@8|A>q7~Zwlh3Ze`ujGAIb&^>^}RWzQS!=~t3C=g1r3d# zGJo!vRNF14)0n94P!9?Ds{ikAR4cVNy1h2}s{jSd)-q-kit`qWRV12SWE*7;_L$)d z^~<`I;GBM55El-4T-Wjk?5InvfAqx#VjJIMDYXghmwvj4Jid0aCk3JWQ}fxhVO?vF zX$}gu?!O(f#`0f}idr*5vnKwQy{w^pS<7O_X@}h8?=4v(o~%AL$5O6LL&lLFTrDXc zhiZntbzXLJ@6Sf?fj-J;j1|C@o&{^o+OfQjj+j68IQL@8+kL`t!-aY@8BtoE7VL+; z3Nf*DX3VjAuw7cpF=T>yX};_VuslOs@%^H3!*iDQY@~B4?x{dxmS0UH>+4xbAwOG* z8tV_lhdiF$71hT}wdM4Dk=rq*PfoiFG6o)26wYw@l(p7q9a-_LWW;v2Kupd{4R@JlRp2OwK{`IQ<*SKDZiz?OGmGF4m|@;9N9H)1uT3=eCQ;v< zDAo_1Q}yq$h2K(gA{i=;SnP=HeR|YC@(_3P*Vo;5JN{2d;jx-NOnYCZbaP3?^LfqT zLH#MOg>QHWgvdSPa2=Mk43RmgNp|6X)^{<`k#)A)s(;(+xN?0=U=E#0q5<>O`dqlPMwDVGrReqZfqfh`M-9-Y7Q~kW^;X36(5q zVAXP|6s2rZYbWs&t3FIF*o`xWqj27|1$Czs2nqMXBa@JsJT;RB$EDS?e%`qdol`Au zuhED>uk}2^_W3UEjK(u7q)8ZOu9R0JQ6>=Z<)9unOO3r%D5MTb2UcPh=iv9v zE89CXct*m-tk(WBlYh6-=RnaSo@KN!MmqG~D@(nk%J;^(Xql_3kDnmF(UrEl-qC7z zK~Kkmlk!5B^~|-O{HpT(!A02q)r z(cSKqfSo2G>N~+20}HpiRoLy z+Wfx8zPuU+uEDLp66g*~b}*d>vDC?j>-4Z>5X0?11h#R?g<7;;&7OO6sF?e(_c`H_ z`?B6%G@6}WR>L1_aF#|Y-Qq3(POK88!mO#5>Py$AbFo7-00&Whn0&Ibbp`dM%4t+f zPjo^!%^-JiR6RA7R2u0>$kTg^cs`JF-<{o?R9q0jesO4THKK*J7`HVVQNAKp&*Eh~ zKfGI-dFyAAGneAG;O~#h*Y?kXnYUOpd-&TkN8N6yDl1I*Xzwr5l-MRcvpS0$J*HW2 zaf=S2o!qC>YUll)FF>GD$fapQ|Hi^Isw?SVpGCq8@r9bFf$|e|-(@oFJG(#oWA`#sHNE(5Qg-vIt)q*q&npLO7XR+m+Dmq%m{cg+)Rl<@eOtI8HU5pbb?*uI53PR@%s6u zyunSjTHazH5P$wkSfksh!c;nz2G#HbZwg%_I6^vA3f@}V!*UR>;csu9#JA_<#=J$R z;$wff_QqpPqlQ2Tiq!9Xbynhg!eNxwVlfp<;7+8c_&HARM|;RVMX-nRy-w*E*6s^; z&bDWw!H+c+zxSfBxynovY)so{;hNy;yQHFnNRF{a>DzfFX)W)e>9_RthUQ+It(B7A zI_k@6e0JoUd8U*#QcU97p72G>*_U}Fc<%alT|YFgqLM}>v=f{wY^8MZdNe%YAF z9H6hmF#Cg=!n?nz>EgeC-d-DmAoxN4u(GnCi-Dkls09s(xE>@%=Zn2ph0|h^SNd8JlT%IJh+9O=nBQm zk#P6=7}ngw;5wCc8k%4@7=)9?z>>0Q+mz{^r1+eP7b6QMt^1^lQ*FOqbMSenb^m_g z=EoxzA#1$|6Je3~EI95ao5C=y69WijntA?y$qm78M(b;sA|9W@Rz2&Nza#`RAD^9n zxjiQ*vTuE938G}vc=IGseS7CVME&sWkTi9rxz_~TNWRS!Jfs;?@3&WdYa$(bmXc)p zqkBlAB$W5cWt>puh$hnZ11ZZcD%%>Yd0pz`nT3sE2(HL|65nKT^Jkk=8Ls@CDU_Ek zD5!fffY-CN%}lr{+q>o2uE7Vs-2@GjUD=rKjzFDWmN8)5mDJSgr<9*){z#!ZcqAR$ zX8Ym%^qFL;N@unRcb)xa9sBltk$R}ocWRK_{Cmq_9VVfY@U@(;T$*~KQ@Xdr5;Wl~ zqjo3{l$!__j~dhDm(T5Jw!69=OGEVH^C@>W{PNCsNpRiQ0&2xD2=8+rik{|kuFDaL z)CL>bt-a%CG))OBciBu20{mjh*^)AqN=l_-6a z`ZeXP)wz_*yK}s|m^_>#6AgBk1k;`O);b%DyF`qryq*`!o=@6wIh*~VK18?7s)~wf z$zmotB-ENltnxh*&5|fV-Y4@Q8+SRa_u)of^fc$-@fxvG)__n1eZsFxZ{@5hMCJ9^ zsFQzNp51gi)zsk$Dm;}i8{mBXuusvBhWq!i0{>jb1>l(fx$sTlGXO=S&~xmT=2hJE z6d9yUTnE1CE2em9T)uFE-Q?-4U+4ufz?|jcTTd9#$t}?gd_;NSq@kQTLV3 z9Ycj_i6YpHmjF=gt=!LVNruM_IK=01&OM>Yx$l>7>C2ORNpk?7QM?yr z5D~E{M-;)5Zjs3ke8Dn8f8J-@bl-n4LlsB}LGtBnK*Y8S>HvUEU#?s65grBm<@|5| z-uv7<|)n=tw~Ug z+p9nSQLKpet_eKt6q^}1Cixx-K(~*iRBa_Itcd*dxG#KiR~Brmf$AtXalPYn;}3GU zyg+3q@!4RnAGlp*Q53lS*yHkBnoetHpn41Py<$R1{hnfjluB+~M7D!bFZYA30Ze9r z*!H62fy2I(dqk~|v#lwXn230lR{6>RFqKTl$}PZTq~Pw0)+F@t1%wRj_Y=vBNy8ay zi296;g53Lnhuw^ay(u&eiGK#G7@%~fw);hL2V_p?2>_ZMl-BAe*4b;EdXT+N;Teq{52xA^?$%}fCQkZ$>K|tNE79I!3DTAzpAmg)I)xw2NF~VkU=sq zx|&&>B!amUmx_$64GL?>ZBPRmL%$lfEVfjL9`Z>9k5Xz*D{<=+aHS$zDr z>A8kA3t%F)nfD`GL9U* z6A9EW7H6y7KCL=uRd@$Za$sM-aTaeRG|?eWjRLvc|FJLb@Fn!P9=@`*0D77wvTSX4 zYX1{eCS%h{MuyiL+N5eFT~^4O|4 zyT$`IsHzAYoR3$Bg45?kmehcNjn=iiB67#yo7KQWP^E`Q17*Y0CJ~Vr6gHx_;Rp$K zJ)Ox^_1fTih@ypQYb=Y<+xMeu1Ii@+wTww3g$H8r|B;=B`RHYU)J8tV%-*;=* z$*gYV2Ebw?4{$osIc==J`a9saOY@*H1;al=%H0P?@(^>AyQ+3M`fIuK>soIvKgoPY zLe9y~uF%v(kczQ;aKSJMlRn9ekIx?;A8*}`_j9n6kH$SZ<}t16Y6@5_596vWNV<0c zqEoQap2rKOF+|B;n04-T1$}RJ^VtcmpwT*_gs(G=ZaJ781axc5nE^-)=}Q|yPZUS` z@AV5e8u&(`c#GzfW9;(y(XZ)fdEm`g=1O0($iJ{jfEs2+^^!DHw(%u#yvXWH1OKz{ z#1DN2j;*?=1iDf?LA{p1tXRE>-sesJZ&+?zus%AY1VWYN|A+Mv{jWDm`6pyp+=&v2 z1$I(>7;W{6dM>7`MD#HY?>`EZoLX**wZ9mG>Mb_ay(daxzvE)=>H|&$?C}>#2Z{0@ z104h~K>)&Du5;RcPn60&Fxz}r8SqOiw-5jFm*J!7RDAh~xe_x`cp`0zm02F}knfTI zYWL#)YGME<#U;Na+8nEi(|7yiM2r88v^EEC?b;PZ)Bm^_FM|FVtftlKQ2?9xyQzwq zw0t9@q%GFY*@mho0vvSWZIG_yli)<&5p{_Sob}mDBcs~DXgilQTV7DP3+}VXLAzA$ zSs6f;8|=Ax(UXrgzy@094asjWvD<-i>xqDQd|Cy%+2#FX3OXjkpt(zpJDOU>O-#eN z87FOuHY$h5j$rk{Beddz5{M9gf6s*%m6Mg{MjFv+xk=C|V7p&`8(J2#tubLy`R#=s zRKMDd)(l{0>MJWN!>hL@6K<~yfjD|}`g2CxDp(gLmt1wuU*WfT9;&Mz_@T|3-93xJ zp>s0zn!9XQ&{J$#*20zkmP{0;tzB(ePzA?2z-WP&rWrP~jnQAs|Cc}Yi)jsHGv4vj zz0@8d&eHt(p>hc0*l1lBoV(aZe{}j}Vq#3)CdHS{zg9Rfr>3G4>xm5BKC!OyIcwHw z;w$%wnUssJ&eo;qvF`^rFGn&Gv&BV|_KnX$anSCw>T24l*01DBx#eALHfeX_{~8U^ z!wB6`aE?Kr%6+EtCJW!j6wKl_r52Z!I;PvdV`n$7(f)Ii)SiV!eqT*?81S zoYHz~;hQ(TdX@DZ@k*<5%z4%rhVUGtX1D$2g>OEJZU}@;R5nOj?V=cc?0WvoEiN9a z;E?CndTn^OULHJ&+#fz0v{7_O_{SMzVMyo*uIyIFPcM<9L2!#K&?=<5-b;OW@(t>s zj3+Fqo-Gfb!yU-1Jej(=HwB9Cc&bQTW+jixA)T~RQ7X&rOX8X_siv&hbOthZUOs8U zNN;xg{G6y#viGi>H;k?*^2`dRo8M7Ta~W-i7fGj` zl*o-7I!0JLQhz)r;6NGHF>3U44jt)i3Z0uXuiY|d=yV^viF@myc=TTA-?Zk=|1Ucs zo*nYNtbm^#Qq?s0Q()^Rh2cW=)#P@@M%&GwF>@HYLK@N*_s|Psz!1(~TW1^8esex} z?>X+VoWdX&E`^ZBOjrEb(7pUgxlB{$(?ofha@h}RZVnC(NT$9K6@AHkxAIxSOjHQ4 zx#I7>?QsULzqf}yKnxk*$K7$Wl_aDwA|fspUf?4)SI0i#_)E16i%6HW&8+`j0TtA_ z($1EGSE{`GpxLQzx54ftVKRnO;v^xK*Z;XTC7r1w@>6|OX@S8_r6}7NhN>G{J5*$C zT^j@`#2XwK%UEG{UYlHDx`b;2j2s*-{iDWnZPyq*7QlmdPik#U25OD!SlxLq;$zuPU4cm z&0@>S?fijX3oj0O{I>@7x%Ui*eiim+Y@-hx2i3b37Jqs$i-8%7Y5}nP)NY^rbg!T( zUF=Z61-YLAj;{0Fm8vjLD5A{?&f{Pjob1b)WDO#=tbRtA`7BJRUl*2LIwT~IsDT4A ziU%VFhmE|mf@5B3G?__mtNlFN$!(bI3yW3p6N+}Lrs90_4eR*^9Y5pi{6@Pbdd6QESm+6hHb~W%Z6>`^f zTjexSA?YY*V1Z*EmW8jqD;>(z|n~?x13<(Mwwl8ye`x5 ziFSsNTjUG}R@V+NlkT=R#`IKnrl1iC=df1GcQ$la>^G#L?~G37y~XE1`^z7|du&~8 z>lZsVAbYNO`%x6xk%%Bz4FT4B8JKnLRQi)>5+W1hihx&DaXx#~at71B64D>iq8Udp zzhYZxB3;wq0NXV-`5!d3LDkHG^FH96Me3fW@tQh7MJuq9ee%|L5`?u67UN5fNfRbI7H0(Z6 zClgNjz^4Cs65x9@X){#RH|>g?*4U|!7Zh*5n&Wz@ZbTk_gbgbhkL^)W=9#!zVCPhU z8pmCri>D*GF~-xq#jQo*y`!f5G>)#x(n|LfIahcrao>l2Eoeo8apL8lz*?fUc8=Z% z2Yyh)y#3iDCz2&*o{AbeVF_i)mh7?%kpE(Vs@hk9ni|m%nj+Pui#|9_Nj0)^>?>eSo__tkP z`S^uJWjIo`T`s-lnQ42&6U1}p*IXQ+Vz!yy+%mV}apU^YTv^=2tK-08?DlogId!WQ zyTdD|ux2N(Z&F`Zg?7hps0Z5x538E%54<0m?PV5x{WIqv-mG>oI2}O197tv(?-4{2 z^gi1SR#j%lU>>tK9Gm?t>x+RpO+X->H@Zu^bHvt50~9y~1t)y{(VKeS9#Ff@krmYm z(fnj>#pSDf1gbv0dMRbN65~(y6$IeP*v>fN|B4lj%b8ge1w9A#vTklTY`a?}IMOjr zeRcp=AFJ1AT$2B`I~20rV=v>meaQ7)rnPH0;f!nRn_fDIw6vg@q@xy-#|i<}7SQ$ulzS0DOj^XuVBU*2oS&K;^b z+i^BB2WR%$*|Q>qx9=dn4Q2HN*ZNn&sMJ5Z#rL$+;EJD6>x3S!?bvVBC1gN-D$*gQ zW${&3`|*b@&>vdfy1lcn?krjS3AlZOP%*>2xvpnnC9c|^BtdB4uscU2=&_|DYQ2zW zjLq(~;t^+d3GKzErUim6k;YpYukz(^ns7cs((Qi}!%E_k*RfSS;>jX*>#7C-f|{jZ z={FNZYS z80*1Y*t5wu-#!&9D3xnK2dY3JYjrP4%>oRu;{9;R&$|ba0mtfP8g7~z_I090B@JTc zNn6VD9oq5HA?l%hZw#Q6Bo=NSA@U6~=QDpeyC}b>^I$jPc~4Q>Ncn7hwm5p?wXxp`z8ei4vjyPn;(1!f=}k+L=t4#ez>F(TI^bmCH-Inu3QKH ztY9|_kFRzOT}Ky-;s^GcyG#Hv;w37%hfD%x)^V4W@?>Ypo{K?BT<=rH->OL& zS>-bfieLbV`$HOZp8FUR8Xikydi2-QF~sr?nQ)EatbK*N{#1b)`OV@t4}@Gsn#-e& zTL|_bKIwNVlfx!KlGY#weI1;q$AKA>;iTKN4e~)gD@Rw`;xnq5;`HBjLbP$E)(E<2 zva!*nZXf)3Q!`lRF5MJE>6&pghZpVGX4Qu%P!aOeK}X~g)4ws;d%voTU6B&v;$nfK zs;F=MS;q#vY?Cf4@E-Z?`#9CBJRIp+k9lJR;e|if`&BXiBSr2;nXXsQnMcIr#|qb5 zB^hF=^V3EuNAlC%499^h5z=vzqa*suJB;Fy&Rp>tgZRx%^YM5U{+8=G11H){;L{IM zrya&pcnKuG^<>asT{3NLyXm>op3q2Qe7y6PAiDBDU&wqU~H1GblonGSbX)MViWy& z5Weaqdq5p#Y)ZL9lw(KR*5zyP`;C#TCw4sUEOF#b3S-UivS9bh_ZP-TClKTBa;9>` zd&p^HZ_iXW_4f>``F|dkw^VXU;cPc7*;Z;2?${mhj!n(@!gxa| zUL!3645EG17X*Pg!-FhkSAi*uZ}L~l`v(ebmT)d#vCMU{Ze`}{yE*r`&yoC>aZEG2 z#2E3?h0ov1$SqLHA|K9i@;7!qS=dm86Eh*N)(fbmsHz;I-6c!$be=Ozn_F#NSAJ71 z(PUNY{8WPycO)q-OWhCR=t!Qi@Cn=ug_P!viOYY$#bUL32+;C|j z_j!9>EymSyQyMthFYSo7bZ^G0`<-K6sZO1pY=v;U%+5K)_Nj1@J z^039lcgX$S6~5?DP8qmnH~^PeVn!p9H0)5;+5Ui?XIv2gL?Oy zM+mOpk4m0KHZYn`libtzW`kkqM#k+W&D7EU^?9*G+^Zl=wAr27rv_wV%>uX8pGz=>;iOiOd7f4dw>EGlW7|%B;#EEdBh%C>Dv9AE?E+`nd{raEl3;c^tJ` z-78LCz-DUd$Yg-k{7L1nzAcj&m|mlB3u0c`RQGSN(-S@j2}#G@PX zP)_lOw4C&Dew=67WxJ8p9ag4?z!By+p4HBJ`66ac(~64g8rOqM-~00=H;nQ%@~;s^ zgbOiW?5Q79?~I?Bn5^`ingWDIqIpUOUWz->Ld=au{eVLf2rux{cF2hP{w-)P^6eKAzI)8;&b>wH`MQyh>zF5nCMrM0n7!f-FM*^G~$1 zc$R8jU7*^hPq>H{iJ(pR&+~9s^@EkMaXO5c$oA(^PmFK<^9v^~aM0w<{?Bv5Irg#v zc&L)e-K*bQ2EOSeFOdVT^BV2RC5zT)%|M(QQTPoVS{ukcrA?x6L4l!EzW>wL$_d=@ zHkD8Bb11nXi#L&6hCswpJs%K)@`Bsn|16UAmCi+9@X;K9w^a`jocLVaSgv$L^rCPe z)slM6FaEmHg@?N+sT2t4(d`);l5zlYU;=?^dD*9x`2@f&8?(J$G#cF`Vu@djv5h@D z4(}=tP_GeqG9}z3gB5N=wp}7(JUWhz1&#OFZ}F75ErE_+N0Mw;bjbg8tG*4l{j?n5 zvo_5|^yS6v_lfB3X;9U@*K_j~{t?bghb}ol1lWR_if^!6)k(z+tjk=*`JXX_Pa_Vs z(W{WxYO05`Bxso`JP;Ge@)0GaG{J84qk5~nzys|u71oy3f@^6(ubv8T@o?13LWV^0 z-=#CnnmTegVv2|~F}If)f7KvE#%bo@zjj62=2DayVnlQ(XVtzoQqcTcHSV_H4s~Ho z{Ha9B_4>o5DJT`E65`=$5+V(Ls+oQt-Cr~r+D9!*f!}VUJq7bje)MkT_?#C$tsU~w zvtQ#&8M*x6twHMklL15Yv64oq@6UO_aq`ch`p`;x84rSuhotCEQ}7u-pCt^>D?1 zuMzRi)s=)zZXF1J+nIl6fLC8or6f{h`QHR~y8S~h%nd3&zA)HU&wX&1xNryreg)ZZvP7u269Ng;R)^6*492~_@l$y~Lq8^V9f=rER8+D`?d zR*A1OT`aM8Ky0f~SdN&8w||?yf2Yb%!mig@-S#5rULtKe;l0nDzXdOHFaiYwaiu5N zi^!#mhCP&0z17F^>2Ie$c~BkGU64H>MC&K@0=Sl2o@!VpVZcHe3sfPOyOW|3``sa23CG&8wbbIVd3g%G_)XsXv(;&?4 zQZ>Hy2(cC2b3xLGHhk@72v93ZEG4(1ZD>9$kr2JG1PrS@F|kyYc8PX{l`*#LpV-jk zY=-hKWW>5syX@um|A*F4(LJWeK5iqkE+Nwov^(k0iRR*i^9Pl(OLGoP%s{6(j)Zrs zBn=1+wk%1{s5)2~h~=-T1%SS9V3Oy`yWPgG!x~s~-`-aNRNQ!a3!NAD-=6U) zs-f^Wc@(~-@~={p9GAN(9iOsYRmM>+!L6MxuwT0%i*T}u^eTqY#v!CP5&Lc^yeO#7 z${>}Or~Ljm%O&+@{C@xVEW8Iq8tGQx5vBa-=ujST)d<2ZJOleFPG^CXJ@r2!P-A7= z3DB$@d!v+|eU5v449C{ZkH7pH@0?(O%$qECqWxNR%l2wEhNny`j3?`+@D1QL?U=Lt zpR!nyfF+X#)+rp0i#GIlJqT^CS=u+;PFV8Mkrk zxWNzNPq8oqW@&_t1uai2kcL9hrgz$878L8a7Up|2Q0LJ7I>K=+`!!X4ES2z1wE=VW z$>I5C6_{y+l8Ku`mx?3Hiv00LJf zf;Ey=y^&NT4q9&9XKTk&0Q22%I8aD_Bh?I&w9Fl)?~czc=~oTGBa6Va?e z2S7(zjf7jMWDYzXi?EwzgzA`4Z5SD!WWhGSKJ~Pn)@i4<4=xJI>pbA*X*7stHfBum zb+SY-Had+?Thd7fq|W=VSfW8I_<66DP*F4x8s?skpJk?#K6r)j(r3`Ct~%_UDJ8e# ztrO1wnNjt@`e==if~x$oa#oC)Xs|;ZB3CP2yQilv6KP7ZjM+qFgSlJa69U5_kY_8* zD=IM8fQ2FjLH8p~HTv^9f~T5_Je}xJx|9Mm3t_EIZjjQ3C>A!awX&c*SEnr!euXT? z1vKg=Ku)AbT@0HHEzavy0{b9W)C!f|qx$43s5jTbi%5=Kp_9?0y1j6*;mS@rQJXO8 zdr8Bt0UyPMe7UDG^^tHudat(#NB~v_oMTmu1+o^D$G681Ch|&#Y(e|6KM0@+DDhY( zE~RR$5fkuzQSd<>(p(rntnM(|XO2~YB3{talIccDG+=eB3Zj6t(g%UpHmY_?)aDw_ zovP$xvF0}wpx`P-FGAiXrzCH&64Hf^A^DpD?u=^qP8@2Xl+B!OHkNOI7v$ z%DCL~%1-~jQ7>GUL|^Xk|^|%XaDLK zTk#oHLa!Jn5HiMeYh(48?OXtls!4f1IOWBoH<->?W(yTMt?ZQ!UAztRMluA5xjl_p z^6EcsLoLn{Dyl3(jG06hzgV}-=X0so3QvObN2+W#X##cBhQ_6zitEjwq^Cet1HTlI zyI(f08gSuRyio`}n(WE1-<{rVZ6iUG;yLRuUVX=e2zjJ>GPYeC`Q@-Sr6KZV5TnW(qltw&OX~0)^D_O4L=VI|WCHd9BmA z=jtzCC!cu%D(sZIai>aa4b2 z#>-MKt?ZU;NBcjoZ$7z&R;y5j3zSK0-`6>n0z z3_*_}N%L~-^$tbql48&#{5dtz+c)u!6g@RD-G^$chJfTtgX`q%_oovgX5<7co3{^f zn>2}@F(@f>Or($ouJQEuS(tfx%PUl4 zhLTM1*ym2qqpe?-&HiDBoQT#oZwND@tNbcUWwZQ;_eKRyL4?96$M{KD4%)?)Eo&l5G?m_8?8J$vXIjnfA6 zdCTnWgM|!sdA*QUGuWF9Q@fh33^>wSjlYUR77((hw$;#>UY)MKRY0!^5 z#4|V1o$aq5o0LTZswjXS;8|sT-zGzqO|AB%~hG@p}cKDDA^;>uGoSGZzONZ;^RU`GCZ+a7Da9LmR@ z;gAn3c5NAFVO_kO0s22)ly9oqJZPCBjy2lz`_KW46zaRHg!=&4lV^r@XJZ_Ffnit5 zh;CKJPHTQz%Sum--YG!=Q1&4@1|~GMX`6=G=VOi&Ti(_R$@*d*;2f6aqJ>@#hZKeHkp311gCe3F2}m>x`LqFmXS6X$C-@XjjS&>+-qnw#&bh> z$A^jUO>UW?>sQ4%1rFx&j5H*RLsZSRz9Y$cMle-usMWxE&H2`Fo|v(+q4srKX#F%T zv8zQ9lPn-%M%7OrYSo~BwydbQrk2U!5*(OG;A2&()D#m`6NJ7hq2t8HBI|s%jgd7M zX;^*wBLl?u3QHz6QwSkrdXK;b{o{Zp&as6~-Lz4~pRearRp^KUP3C!@0e|yGNiiMd znelpL&+KqfK)|nOFnY13Rm|}7147F4N1iDKwi@?ETaHdtVyTWh)%`M#CdYU;qV;yt z&bag{ik*73Oi75sDdT6VCoWW4TDA5D{Q;R4^zW2?H9kAuU_D{-^g`MPzujL(*z%6t zB>&Ly$Z^6;F1io%kyTv9O@gkXxBEdEVj~)%G-3utkA4yN+Q6Sr07{YSPTgwdOLM8f zAQ_-Cb(Xn{;)I;MzaH8K<1owMY@;H<{k*6YlrD$-OW5Sdhz=+Vt?-YqCQ*o)?7}8sCjMhG&)|WguLEm zgE(5OB-E;U+KEHkQ=HCf161>na=33>qE(ywX>B5xTl<{6CW!-V zmNijQ10Bx>y%U!-x6ROT*;)72lPnp!6SBtGn%Tz&2p&bUOMq~u{`$>8v&nicgBfUY zGrMr3MvF;FS`LrzmX2AL^!g+4(a?R^dDqQ!{3NCRi{MbPsWJx(iy%}9K>)SmUZkwIOB`@Jj3Ra&qVM2iW8=4RC{9bfBJ&koeB`{o^j_p!!Nz z@VBLxX(v`|WNKcmKBV=o*;3|P-*%5MbeP}w2ZOBZis1t4Ownz~(>9Oz&7?n%t`f0a zi=W|3p40~8eDxDrvC9krfm^5@tB6$oYV=<<7Jb#xYV3-SvvcPZz6E0aE=UJM_0Z&| zIep0u)Ma-?NcvH$45c}3MWZ>`oJs08>#?Dy&}Nbn(`vl{M|3d_+6T_1fx(VRs{646pU0ioEo~IaI@T+sC2p z<*(~mt-}I4w)v~m!k361&Ll3`_@t{#Oww{JJM7ndAWUo{H&C_&y@X7uilUR?);M*s z>dN!SKi&JLe203Obz;YQ{nZAQ^D8Tlagub?coth5`l=!P&d9dCXhP>`vITw7kVSBw z<51t4)1dd9HFgCb+@eCV*%>%ow^RR6{JHI{?9@guEsb%T=kNz7U)hh|Omf!6S@L-B6onpOeiG58&xO4YgJVypf1^I z4v2x6u3Vi+3XUqU@H6IN7{kb-Q7gwEA1Mokh^uHw9=3LU%HA|eZU`x+y_qSvIf+^h z1q881g~T2)zbx@OkIW9*3aWpq)@ng2E|m#&93p?bVfOrBBec17dw&wtvxU^7+aFf( z`ncpAj_+S}+!V%iVPcQwOZ>rL?w#%w_r4sjpYMD(8pi0)X*?#^5www8(T}%&gJAje zPLm_lW?>=E)vcL2h&ZG5RVW|*Il*W&m3?`DZX4HRYEjWaNt z)CXiCzYL6*IkTkHX^vde+~RwiLw3q{hQ4{vd4TQN565Qd3-k$kIjNYic$r(v#I}TX6q!)e>h(Qgp?6D-Is@cIx$!UXZh_|K8F-ja z$5H|x;CcJ_pPUMFu$lOZUUckBf6SJ=irMy)^b0waH$j&e6N~HK(0n?*&{H9O_uxWL zofNFx#U1H(8il8#+tElmBGHVd)D+($J5(MfnVFbbH>xb78onr84?;u)s zvdw_9-A6zw%PQc6OiIN$4YGYwhdhLErvaI51*=EOm7a0DH412zdrVtitNYrQe(0J2&pcg0@t-NS+%6TnQA^U8TmpkKTwLAE4D(D}yp0 zve`ZNaqxU?_j8uLtiG05Lv$B3s^f0XiUTtVm4_K*%4)?p|0 zd=;f-PR(DjHgoa=VwuooX>RZ6G`;X9P%=B26Z8(Ysbj!S|9}u8ga3)(tsI+7LD2Tj~N!^>0W~e+?@U-^=a#Y51F46q;*`1 zf@r}kJKVCMV=R`nqNoy9rt)=<#lFD&fq-b2(v)qV@otX%9rB^AS_<|3%(Gi%?#)`X+ zA?zpIbrt1#ES+21!2 zbkSwr^gNF*5h*@hkw{~h-SvkihY(=!{>Wvg&2j3XUV6~Rk$&{HcYh2w_{3ZP>!3pY zD>0$EayhM=DJP%xXBpEzt*zy7E{7iX^BamvMGt#J5Em6kQx8kf1h*x(j2 z?i7eX{G6%MO7K$9s8>sGd6@dgyRkPs_9NME9r33_XPoEDB2a1&9GVjTbDzvRv)0h3 z8*6+&HF4N6$-4=}pZTQ&2DOb$Q#~}Zz4p2I3b+HrRPy@IDV^<*DRd>Y(7txbD_|PK zmR$EyYj(|7aGtz9j%))*PICV{B^tS-`ZZmU&W zFlIKvJVzb8yW{R)f=2MS%p$8!t7%VW5ALy6Sc1%gmyqa1s0OIrrNXQvX=m8!_PeL~vWmS8>2U7Y{Vk6)(!KIvCJeIiOnH?}qL8;}%1%lis&>H9XI zr_J*kn&&P?ppMtfp0ZzT@bopDs*JkaM-Y28HcyuF$K9DadDKg(@GV1_IkC4|1hBpi zAJ^2?Ooc!~5a-RSV(hvaF6GdtQvKem0Qm9br%i+Xb1|6`5%!c`kN4ogj8zTwM#ti@ zgZQ?9<`H?vnGwI4+ZpVtD-&$V0wL-LKmv=vy-7mID^1_I=}#0>QOoIn`U zz4E1_*^HZ{_ytX?!3P_1ffMYYWX6#FxrO~+^D2&5cyTOgX?RTi(DrZqps+^ZOKa*T zb2(!I1{GkP1almBD8qz~u?>sK+l$XlJ7<(=4Rzc1n(xEARE^x+XeY+^kH)sqkIPL; zn@-ZLO3Ey!)Hk(}^UpaAv~|tZ0nEo~bk?*Y!xX$gs>L(N@E``pF!hFSh2Ob9 z8sC3C`gC2~#r?yJN#w}^8Ggyz_e9>|a-)%%eX9%j)#*;4=ueS02xKS7*duup9ibAI z^HOMVYMMNyi8I>FiUHXr2Ir2r5{QOM?yu#~j2#gYg`Xb`&3O}|mjqpE550}lTq^O> zW_shlV{w>oY?R(SM&e<^0NK*pXZV4qL9`~!V{2x=)pAPo9u6WZm+c38LBG~Ul;P^bcs+AcKQd+Zh& z9G~<>`R((GN~2D!i#!}xI->k8yVXpR!R1wyGf4W}dAkH>M0R50nLW`I`_zj#t~je- z{`|Pn6-YCRW10fBjqBHrsq2+ck~g;7ZcHWRfDX#hvy38VWrJS0X_@A)xe(V+swkf; zY&7f>nGiOZ+em6K&mp|Egn?6dAM@^;g?6{nZQ;fxJ}V2Q#EX*~Ebm4`Xcb7{#$kW`S9UioB*r3t$0(!h9* zo?P-JXq4;Lf4p6>*>VLB2ghatw(1>ZUKgWbuBKtxJ&ZkfPHvb~GQbIFOmcV+2sEom z4`o6(xO`V&c3fFOW%KuaT#tK0iHN@HLUfg=xY$;IQ|0wZF*aKLGS|Q5P{kX;s$x zXZ!n;poO`R4}cy-(jw6LDO8c-eID>2B^v1?qpw-{olL%~kfEGYR1;`mpA_3v8b17} z(wg$aaYMMZ?&fjL^}HOi-&L$C>mcUG6XTnkgn)95Jpsk+U)?6D?F8vdL|?uuKZwnE zk}IdJt$YU6ngSph1LBVsG6|x^8y(gRMZYhhGfHj0WptZ*qG4qqxRNR6%qigPpUnscO_X81$16=9x=p`8 zL5)TO)%_RDW-CVMwH_P~F#{Ei1{!9!&|VWqA(*_8}hU z!Z4?T1BCR(08OnP~koGwVkzRiHDybNO9u9nbp8LmsdpKF})bBtXJ~e7> zEj4~m;qe@On>a~)&o!cZLn?gEj;!O>O5!@czx|p~s$aj3HkS>{qs=NL!`v&VGz@pK z2EM%9VWlOJZcXYmf*!QaNd#C|7CeDO|{d6-jis!>Jo;&g2% z9>wIjF}OjnPo(#DVmFH~)Q`N(;^)*l!|qB*gufr%$)R8^&@zJQWADrNg*>tXpPDnk zzLV|L361?GZUif_UC$WVmASC6DJ zy0iP`&*A+)Jsix}{SFPrELvrMrdFaE?lAE(yNwz9Z*CTu9?6)6*tvx&PK>GREiEL1 zb1LUAY7fWe_-{RX?d?a`awy2fRb=CIwiqiJCY9N7#*j_d%gjs!$z;ZTTAZ-?){gTZ z2~TufZy(DRDGJa?r2bX~4)Cmp?%oa}QIT$VT|-QJKGi}uz({s3zMiud%(_u2@tKvjj&mj5HXSSBg;(3R&~i6S z&BrQ4(xE?#Te2><=c?&8DlS|8iGO6VEL$;IeWo=QA3a=b8g21ypCyC;N>qBcn_)rD zqX5l!xjjS0D%-M>-|jR-EBFD^h8YgpZLfkiqct@(W7Yg^c|(AvfM{yeJe$vU5VD}a zQ5ejc@^={dhh5TS-^21800+t}o{}swN;yh=j+szCsF>N-!afuX-~?Hr&r}wY|0XeL zN|Gyw4z$WFx^ufgIUsm8#ZvEr`Y@@mz-VzG)%4OG&LI-ra#Ya;+EH%TR-{>zWR*tE z2(om1_!s6wQw1;|5_$JQC7R%{C_~1=#0$DaVF0i!9*=cif;>&|PVK0_p^w)dQM8p- z9-&vL^NB&rf^3sVhQ8&`Ul2iGSZ{25>GaiP)1EUanv9m(7qwI1u|Veo;wHBqXS)Hu z>O(X{VIV5Lu$&pPfjuWnU6Aa|fs%54GiQkb#t3*Y1XbzU;XzhLO^C_Jy`J*Qw~3#E9VI;cmYdv;TGTnTgNt< zfxXeW15D7Mkn~Z0dkpD$vMk=IZLbMcVZbB_;(A#gxM8SRDaD-Ea6kw2$^;jZ;MsE^ z6^E4pXeiit%NW|ey&#@ci;4m9#DR>y2p11S<6KWPcou{ewejQv*9KY6nJJaG2q{x` zU~>^{hr2;AtB2#oWTG^Ejp`CkVR)*J5Pnc`g!2s{OxC7R>xVsxAGzSI#7rYm((&Eo z0$-5@SMJHGy~EKzolM&6=E2t5zaLOaHe8Ityw`+wha(3SlqA?5-yV$aoDKd0^b-t! zobEh9XRQ2dlyq9Rhu~KvQsUb$cRo{W#e6C% zOLdp=ari~xCPR1DMJlBK?!nvvB^-GOMfs;?0)8nh(=3RWh+oY8HQ=ni=ueDxSuILb?rGi%~nJA*?u(?7-MT~0mnpoXf@i^UaH zt_EVXE!pknSAfP`HpX0Jxa@bqaThgBzQZurKJSMju->Vvs1(+C;z8zbZi@xI!99_0 z<>g|h_vV3F0=vOfT7BO!q@nNZp9AYLh_dEy2H@tPk(t@JXOAuZQwPp%3X2b6v&Od* zLVCNFwNb-gv$gR-pykujWKet1E=UBodBUh)+LcTlE@f(N!!w;vH;hzOiGZC%$5aGE z8$SdpIQ^RxT7X+RRGC5A1v+Dhvb;_(FiXP&)st5Mz51G)C1I4^mEDUtuKiLb9^^IX zHfR@gGqp`_mSvPk*2LjAi>@+X)t zx((=8?vXjf-dM2oTavC`ESqLtlDxTmVPu6LM@K}Ikel} zM*XS)-g<9(BYgPrYULhEcdXVa%!M-5Ad`|164xG%qH5Ku?>_^SVZZ82oU;Lv)G?># zLo-K#zsja&8sg`rlPb)!)>qp;EE80E%x747fg0y67xfyWTbok17Q8F1LHKP#&u-)n zjw98ey*w^dcUW8S&}dZ&L+KyS58{W5$+Q%GOyK^=@*R`L2XJID6V6rMasTrq&D-eB z?-P!A%FL1hlLam}&N8pcrWO?l$)f+^8L)v~5qXljy-bt3GvHYA%btN6M3>8xfqxdY zw9?BMw^gw%kDnF%f+**>pHju?Qj_nDMc)maW*=Od>~C)9AABC}TgR!*#8_~7rEox- zK2W;{(Q0=HzNjNv{H|p`VRxQWA<(VsUN|a?Qd~M&kr3In|3LF4L*Ivt~OO1HMMv>*)>La zLB75gy5jXiH(vHJ`u)(QT}dD}*eBgd0G>#w{o4CoVu=_KWZu}6cr;I0B9h0m zFR8$QE?I3fo|E`Fz(k1AMTvUMDi>kj{X{%4xvoOg9l4 zD5LaAKeH!Qzz(M78CTLs&b0Ad0;-$DQziZ>H zaQ?bQv@2oFc|a|lVXNT7-5bdneeKlYQ6&s^nox4rr*#=4J`V*@_lupcMru~0#&PuI5;pa%Q9R_{^$ z{8!{C&+txvJLNn8XF^GtQs+;#;t>v1x8zQCf3IbW-`#XK@|4-VY+;@#bOVayyj8!6 z`Se9KWTEy)bAKkLR7SZv*xa@sGs6|lWaqqU#U;81afv$7sek_v_LL9kD3iR}50NP4 zqN!`XeW#+fRYnbYuA}^zh}7RtI_&xc7-#q4LS5ZRsu;~!Swz3)&lnvChr-RBmEoe5 zIlZ2t4_zsR&*gcsq^n>%m>Q1q&!UK}{#$yv2>B1`>^9sA9b7AGtfN8vRqylP(i$9!u{{Q;j-;mgSxI=vRQ|g z4`}Y+MJyxy@?;j$BNj=8Bd;$ENu8YT1RI{5Ht(MxUD8k+3^!$5T}t$vdMKD3XdRhP9$H>N0ZB>drtL-J$SVj%ve|_(#2) zrNm0Znrv{~qQSK7RWaixshJ_79UGJW7mZ@i(AZvSElT`uE>4t~iwP%6Y_e*nIg{as zcI9X;IbpIpHgLg&RNIauQMa8Aew|U*@I(t>lL&!jL?&<4=trn;ydP*D&3W^b+pRnb z)P=6-z((F(JHl5v8Bzj@y$%sTu{Yz6f#>nr{>Fkxj9?7GVZy5_4lJK;{z#EB^)@qS zI3v#G+ z_r=l1))PMHSSN(cxJsICjjTh~x$k$m1oZ8$P2AY%^3>kdN1Mk;R^_d8OGk)rT^W_* zQ%LT8b(F&*O*XH;UGiozuYkS{_e-<&zR8kg-mGIGmHky;~9GvPyM;bWL|;9$B>Y}Q7_{UykUFuoteXx zJr=hjb(TTf-nG)rUof$odCvTL}aF@d8w0cA{9sw)%$daNkJz*yQ-SrDG<4UVaU3rVfbIQ$Vq}tO{ zYzxz6{#`pZw4=ia*%VcC2Dxdrb11Our3c-d^)Z<@X`Q!NNfHSU-Rj+AY1MN#cQHc~ zg~{eMs!7g9&iLnXns)04n2Xl=+wo3LSG;ZQvc^63+Ljb+o6wp4#>#N|b`!MfEg3wK}RMJbATxlzjvaYx&Ayx_Whd z9-*FS<}rq>k9ENk!tFVM31>#TXCaMzrs`FPn=7J$M-CE7SQF1F#!_D1pA%+|H2lBQ zWXD}E^+AMFq~721X3UVhF(v87wl;F&zVn&ed_nmhqW#zkt27`!rS!e^)q~@nFw=Oy z*uDk{U9OO%ssgbbl`Mm|+TT5j+Gio8kM2Z{w$4!8FGSyqC+?PMS>90(ZES3>CB}%# zVrg|>=_dB%ptQ9ZFyC{`k~$q|x?Jq=+FOSYwqw^v)g$-(Hp)J!xq;Og=*X zNXUW&)LR1me^WoECyQPxQ;Hq{yk)dE7Im3n!zv&KUhc9v0&3fyZ z0qmhKB@aLAN6ih#*Sk}?ueMC0zWOe0(ka?5pc8(KY=3O--cDE!K%~7Fza}Gf?0x99 z-!*lTfcl2&4cJGVI<}Mz#E3#}vU&UMdHXpZ+wB~8z@?JvPkZ&vuJE&Gj2_)-rN`u0 zZu*=G{dj8ZchCEjCZhGW=f+i%8QW*(RYPQ^e2MyeqNIZ2x?Ja-aZ{`vFG#H6HMqgBt9er|KF%gM_ERWc7p7ILv2&5p*&*i)iwViSb?Z(?(S0`1Mj-89X{SyeXk z?UYgXC5wZyVi^>bOTZ8{t8a|;^mBq1ikG{Iyhb}lkbcycB+t0io`#W~!8G^ywswy*0p!<-o?@T2KsJiG2Iaao;M+Cm8NZpRMZgF zL7doQ2@o8y1QidtBSzi4J{%nf)kf^@-0HmqO#{_Q2h~|0NJSpa&1Hwu2aUNo<3BY% z>>*fbueqFQVu-L8JcTY_!dqz;zZ~Q?TYWX3YLPW)Kg9t2Iu491t*zNuH@O>$TvuDg zk4UWvpBi_}Hs#~W9O|_2Fn4pi$HULRSPgM*xS7n$M*z9yP5*fqRNVuPxF;E5!t%Y; zgevPr8rQ1@u_(<05{P>O>V?q*Mv|LXOZaVQEWCiPDrMG-zbI4jo`P1N_iS6&$aQ3w zg{Shh>{*#6Ll_L^eoCE;H{AyA91VK@W|zge*b}5@Mi5X8;8&TK3=U4gdD!~h3;RqB p--vSsImpoaztjGoB@v-%4($6qI+{1O_!?Iy6$N$qQn{zW{{@H4ea8R* literal 0 HcmV?d00001