xiuos/Ubiquitous/XiZi_AIoT/services/boards/imx6q-sabrelite/include/registers/regshdmiphy.h

/*
 * Copyright (c) 2012, Freescale Semiconductor, Inc.
 * All rights reserved.
 *
 * THIS SOFTWARE IS PROVIDED BY FREESCALE "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
 * SHALL FREESCALE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
 * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
 * OF SUCH DAMAGE.
 */
/*
 * WARNING! DO NOT EDIT THIS FILE DIRECTLY!
 *
 * This file was generated automatically and any changes may be lost.
 */
#ifndef __HW_HDMI_PHY_REGISTERS_H__
#define __HW_HDMI_PHY_REGISTERS_H__

#include "regs.h"

/*
 * i.MX6DQ HDMI_PHY
 *

 *
 * Registers defined in this header file:
 * - HW_HDMI_PHY_PWRCTRL - Power Control
 * - HW_HDMI_PHY_SERDIVCTRL - Serializer Divider Control
 * - HW_HDMI_PHY_SERCKCTRL - Serializer Clock Control
 * - HW_HDMI_PHY_SERCKKILLCTRL - Serializer Clock Kill Control
 * - HW_HDMI_PHY_TXRESCTRL - Transmitter and Resistance Calibration Control
 * - HW_HDMI_PHY_CKCALCTRL - Clock Calibration Control
 * - HW_HDMI_PHY_CPCE_CTRL - Color Depth, Pixel Repetition, Clock Divider for PLL and MPLL, and Edge Rate Control
 * - HW_HDMI_PHY_TXCLKMEASCTRL - Tx and Clock Measure Control
 * - HW_HDMI_PHY_TXMEASCTRL - Tx Measure Control
 * - HW_HDMI_PHY_CKSYMTXCTRL - Clock Symbol and Transmitter Control
 * - HW_HDMI_PHY_CMPSEQCTRL - Comparator Sequence Control
 * - HW_HDMI_PHY_CMPPWRCTRL - Comparator Power Control
 * - HW_HDMI_PHY_CMPMODECTRL - Comparator Mode Control
 * - HW_HDMI_PHY_MEASCTRL - Measure Control
 * - HW_HDMI_PHY_VLEVCTRL - Voltage Level Control
 * - HW_HDMI_PHY_D2ACTRL - Digital-to-Analog Control
 * - HW_HDMI_PHY_CURRCTRL - Current Control
 * - HW_HDMI_PHY_DRVANACTRL - Drive Analog Control
 * - HW_HDMI_PHY_PLLMEASCTRL - PLL Measure Control
 * - HW_HDMI_PHY_PLLPHBYCTRL - PLL Phase and Bypass Control
 * - HW_HDMI_PHY_GRP_CTRL - Gear Shift, Reset Mode, and Power State Control
 * - HW_HDMI_PHY_GMPCTRL - Gmp Control
 * - HW_HDMI_PHY_MPLLMEASCTRL - MPLL Measure Control
 * - HW_HDMI_PHY_MSM_CTRL - MPLL and PLL Phase, Scope Clock Select, and MUX Clock Control
 * - HW_HDMI_PHY_SCRPB_STATUS - Scope, Comparator Result and Power Bad Status
 * - HW_HDMI_PHY_TXTERM - Transmission Termination
 * - HW_HDMI_PHY_PTRPT_ENBL - Power Sequence, TX Clock Alignment, Resistance Calibration, Pattern Generator Skip Bit, and TMDS Encoder Enable
 * - HW_HDMI_PHY_PATTERNGEN - Pattern Generator Mode
 * - HW_HDMI_PHY_SDCAP_MODE - The Soft-Reset and DAC Enable, Clock Alignment and PG Mode
 * - HW_HDMI_PHY_SCOPEMODE - Scope Mode register
 * - HW_HDMI_PHY_DIGTXMODE - Digital Transmission Mode
 * - HW_HDMI_PHY_STR_STATUS - Scope, Transmission Clock Alignment, and Resistance Calibration Set-on-Done Status
 * - HW_HDMI_PHY_SCOPECNT0 - Scope Counter on Channel 0
 * - HW_HDMI_PHY_SCOPECNT1 - Scope Counter on Channel 1
 * - HW_HDMI_PHY_SCOPECNT2 - Scope Counter on Channel 2
 * - HW_HDMI_PHY_SCOPECNTCLK - Scope Counter on Clock Channel
 * - HW_HDMI_PHY_SCOPESAMPLE - Scope Sample Count MSB, Scope Sample Repetition
 * - HW_HDMI_PHY_SCOPECNTMSB01 - Scope Counter MSB Channel 0 and Channel 1
 * - HW_HDMI_PHY_SCOPECNTMSB2CK - Scope Counter MSB Channel 2 and Clock Channel
 *
 */

//! @name Module base addresses
//@{
#ifndef REGS_HDMI_PHY_BASE
#define HW_HDMI_PHY_INSTANCE_COUNT (1) //!< Number of instances of the HDMI_PHY module.
#define REGS_HDMI_PHY_BASE (0x00000000) //!< Base address for HDMI_PHY.
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_PWRCTRL - Power Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_PWRCTRL - Power Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : PWRCTRL Access type : Read/write/override Address : 0x00 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_pwrctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_pwrctrl_bitfields
    {
        unsigned short CK_PWRON : 1; //!< [0] Clock Power-On
        unsigned short TX_PWRON2 : 1; //!< [1] Transmitter Power-On 2
        unsigned short TX_PWRON1 : 1; //!< [2] Transmitter Power-On 1
        unsigned short TX_PWRON0 : 1; //!< [3] Transmitter Power-On 0
        unsigned short TX_PWRON : 1; //!< [4] Transmitter Power-On
        unsigned short RESERVED0 : 10; //!< [14:5] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_pwrctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_PWRCTRL register
 */
//@{
#define HW_HDMI_PHY_PWRCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x0)
//@}

/*
 * constants & macros for individual HDMI_PHY_PWRCTRL bitfields
 */

/*! @name Register HDMI_PHY_PWRCTRL, field CK_PWRON[0] (RW)
 *
 * Clock Power-On This bit powers on or powers off the clock driver.
 *
 * Values:
 * - 0 - Power off the clock driver, if the Override bit is 0.
 * - 1 - Power on the clock driver, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PWRCTRL_CK_PWRON      (0)      //!< Bit position for HDMI_PHY_PWRCTRL_CK_PWRON.
#define BM_HDMI_PHY_PWRCTRL_CK_PWRON      (0x00000001)  //!< Bit mask for HDMI_PHY_PWRCTRL_CK_PWRON.

//! @brief Get value of HDMI_PHY_PWRCTRL_CK_PWRON from a register value.
#define BG_HDMI_PHY_PWRCTRL_CK_PWRON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PWRCTRL_CK_PWRON) >> BP_HDMI_PHY_PWRCTRL_CK_PWRON)

//! @brief Format value for bitfield HDMI_PHY_PWRCTRL_CK_PWRON.
#define BF_HDMI_PHY_PWRCTRL_CK_PWRON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PWRCTRL_CK_PWRON) & BM_HDMI_PHY_PWRCTRL_CK_PWRON)
//@}

/*! @name Register HDMI_PHY_PWRCTRL, field TX_PWRON2[1] (RW)
 *
 * Transmitter Power-On 2 This bit powers on or powers off the transmitter driver for channel 2.
 *
 * Values:
 * - 0 - Power off the transmitter driver for the third channel, if the Override bit is 0.
 * - 1 - Power on the transmitter driver for the third channel, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PWRCTRL_TX_PWRON2      (1)      //!< Bit position for HDMI_PHY_PWRCTRL_TX_PWRON2.
#define BM_HDMI_PHY_PWRCTRL_TX_PWRON2      (0x00000002)  //!< Bit mask for HDMI_PHY_PWRCTRL_TX_PWRON2.

//! @brief Get value of HDMI_PHY_PWRCTRL_TX_PWRON2 from a register value.
#define BG_HDMI_PHY_PWRCTRL_TX_PWRON2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PWRCTRL_TX_PWRON2) >> BP_HDMI_PHY_PWRCTRL_TX_PWRON2)

//! @brief Format value for bitfield HDMI_PHY_PWRCTRL_TX_PWRON2.
#define BF_HDMI_PHY_PWRCTRL_TX_PWRON2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PWRCTRL_TX_PWRON2) & BM_HDMI_PHY_PWRCTRL_TX_PWRON2)
//@}

/*! @name Register HDMI_PHY_PWRCTRL, field TX_PWRON1[2] (RW)
 *
 * Transmitter Power-On 1 This bit powers on or powers off the transmitter driver for channel 1.
 *
 * Values:
 * - 0 - Power off the transmitter driver for the second channel, if the Override bit is 0.
 * - 1 - Power on the transmitter driver for the second channel, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PWRCTRL_TX_PWRON1      (2)      //!< Bit position for HDMI_PHY_PWRCTRL_TX_PWRON1.
#define BM_HDMI_PHY_PWRCTRL_TX_PWRON1      (0x00000004)  //!< Bit mask for HDMI_PHY_PWRCTRL_TX_PWRON1.

//! @brief Get value of HDMI_PHY_PWRCTRL_TX_PWRON1 from a register value.
#define BG_HDMI_PHY_PWRCTRL_TX_PWRON1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PWRCTRL_TX_PWRON1) >> BP_HDMI_PHY_PWRCTRL_TX_PWRON1)

//! @brief Format value for bitfield HDMI_PHY_PWRCTRL_TX_PWRON1.
#define BF_HDMI_PHY_PWRCTRL_TX_PWRON1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PWRCTRL_TX_PWRON1) & BM_HDMI_PHY_PWRCTRL_TX_PWRON1)
//@}

/*! @name Register HDMI_PHY_PWRCTRL, field TX_PWRON0[3] (RW)
 *
 * Transmitter Power-On 0 This bit powers on or powers off the transmitter driver for channel 0.
 *
 * Values:
 * - 0 - Power off the transmitter driver for the first channel, if the Override bit is 0.
 * - 1 - Power on the transmitter driver for the first channel, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PWRCTRL_TX_PWRON0      (3)      //!< Bit position for HDMI_PHY_PWRCTRL_TX_PWRON0.
#define BM_HDMI_PHY_PWRCTRL_TX_PWRON0      (0x00000008)  //!< Bit mask for HDMI_PHY_PWRCTRL_TX_PWRON0.

//! @brief Get value of HDMI_PHY_PWRCTRL_TX_PWRON0 from a register value.
#define BG_HDMI_PHY_PWRCTRL_TX_PWRON0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PWRCTRL_TX_PWRON0) >> BP_HDMI_PHY_PWRCTRL_TX_PWRON0)

//! @brief Format value for bitfield HDMI_PHY_PWRCTRL_TX_PWRON0.
#define BF_HDMI_PHY_PWRCTRL_TX_PWRON0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PWRCTRL_TX_PWRON0) & BM_HDMI_PHY_PWRCTRL_TX_PWRON0)
//@}

/*! @name Register HDMI_PHY_PWRCTRL, field TX_PWRON[4] (RW)
 *
 * Transmitter Power-On This bit enables users to power down the entire PHY through the I2C
 * interface.
 *
 * Values:
 * - 0 - Power off the PHY, if the Override bit is 1.
 * - 1 - Power on the PHY, if the Override bit is 1.
 */
//@{
#define BP_HDMI_PHY_PWRCTRL_TX_PWRON      (4)      //!< Bit position for HDMI_PHY_PWRCTRL_TX_PWRON.
#define BM_HDMI_PHY_PWRCTRL_TX_PWRON      (0x00000010)  //!< Bit mask for HDMI_PHY_PWRCTRL_TX_PWRON.

//! @brief Get value of HDMI_PHY_PWRCTRL_TX_PWRON from a register value.
#define BG_HDMI_PHY_PWRCTRL_TX_PWRON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PWRCTRL_TX_PWRON) >> BP_HDMI_PHY_PWRCTRL_TX_PWRON)

//! @brief Format value for bitfield HDMI_PHY_PWRCTRL_TX_PWRON.
#define BF_HDMI_PHY_PWRCTRL_TX_PWRON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PWRCTRL_TX_PWRON) & BM_HDMI_PHY_PWRCTRL_TX_PWRON)
//@}

/*! @name Register HDMI_PHY_PWRCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_PWRCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_PWRCTRL_OVERRIDE.
#define BM_HDMI_PHY_PWRCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_PWRCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_PWRCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_PWRCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PWRCTRL_OVERRIDE) >> BP_HDMI_PHY_PWRCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_PWRCTRL_OVERRIDE.
#define BF_HDMI_PHY_PWRCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PWRCTRL_OVERRIDE) & BM_HDMI_PHY_PWRCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SERDIVCTRL - Serializer Divider Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SERDIVCTRL - Serializer Divider Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : SERDIVCTRL Access type : Read/write/override Address : 0x01 Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_serdivctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_serdivctrl_bitfields
    {
        unsigned short TX_SER_DIV_EN2 : 1; //!< [0] Transmitter Serializer Divider Enable 2
        unsigned short TX_SER_DIV_EN1 : 1; //!< [1] Transmitter Serializer Divider Enable 1
        unsigned short TX_SER_DIV_EN0 : 1; //!< [2] Transmitter Serializer Divider Enable 0
        unsigned short RESERVED0 : 12; //!< [14:3] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_serdivctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SERDIVCTRL register
 */
//@{
#define HW_HDMI_PHY_SERDIVCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x1)
//@}

/*
 * constants & macros for individual HDMI_PHY_SERDIVCTRL bitfields
 */

/*! @name Register HDMI_PHY_SERDIVCTRL, field TX_SER_DIV_EN2[0] (RW)
 *
 * Transmitter Serializer Divider Enable 2 This bit enables or disables the low-speed clock in
 * serializer 2.
 *
 * Values:
 * - 0 - Disable the low-speed clock in the third serializer, if the Override bit is 0.
 * - 1 - Enable the low-speed clock in the third serializer, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2      (0)      //!< Bit position for HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2.
#define BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2      (0x00000001)  //!< Bit mask for HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2.

//! @brief Get value of HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2 from a register value.
#define BG_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2) >> BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2)

//! @brief Format value for bitfield HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2.
#define BF_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2) & BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN2)
//@}

/*! @name Register HDMI_PHY_SERDIVCTRL, field TX_SER_DIV_EN1[1] (RW)
 *
 * Transmitter Serializer Divider Enable 1 This bit enables or disables the low-speed clock in
 * serializer 1.
 *
 * Values:
 * - 0 - Disable the low-speed clock in the second serializer, if the Override bit is 0.
 * - 1 - Enable the low-speed clock in the second serializer, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1      (1)      //!< Bit position for HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1.
#define BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1      (0x00000002)  //!< Bit mask for HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1.

//! @brief Get value of HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1 from a register value.
#define BG_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1) >> BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1)

//! @brief Format value for bitfield HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1.
#define BF_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1) & BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN1)
//@}

/*! @name Register HDMI_PHY_SERDIVCTRL, field TX_SER_DIV_EN0[2] (RW)
 *
 * Transmitter Serializer Divider Enable 0 This bit enables or disables the low-speed clock in
 * serializer 0.
 *
 * Values:
 * - 0 - Disable the low-speed clock in the first serializer, if the Override bit is 0.
 * - 1 - Enable the low-speed clock in the first serializer, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0      (2)      //!< Bit position for HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0.
#define BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0      (0x00000004)  //!< Bit mask for HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0.

//! @brief Get value of HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0 from a register value.
#define BG_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0) >> BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0)

//! @brief Format value for bitfield HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0.
#define BF_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0) & BM_HDMI_PHY_SERDIVCTRL_TX_SER_DIV_EN0)
//@}

/*! @name Register HDMI_PHY_SERDIVCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_SERDIVCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_SERDIVCTRL_OVERRIDE.
#define BM_HDMI_PHY_SERDIVCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_SERDIVCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_SERDIVCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_SERDIVCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERDIVCTRL_OVERRIDE) >> BP_HDMI_PHY_SERDIVCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_SERDIVCTRL_OVERRIDE.
#define BF_HDMI_PHY_SERDIVCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERDIVCTRL_OVERRIDE) & BM_HDMI_PHY_SERDIVCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SERCKCTRL - Serializer Clock Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SERCKCTRL - Serializer Clock Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : SERCKCTRL Access type : Read/write/override Address : 0x02 Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_serckctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_serckctrl_bitfields
    {
        unsigned short TX_SER_CLK_EN2 : 1; //!< [0] Transmitter Serializer Clock Enable 2
        unsigned short TX_SER_CLK_EN1 : 1; //!< [1] Transmitter Serializer Clock Enable 1
        unsigned short TX_SER_CLK_EN0 : 1; //!< [2] Transmitter Serializer Clock Enable 0
        unsigned short RESERVED0 : 12; //!< [14:3] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_serckctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SERCKCTRL register
 */
//@{
#define HW_HDMI_PHY_SERCKCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x2)
//@}

/*
 * constants & macros for individual HDMI_PHY_SERCKCTRL bitfields
 */

/*! @name Register HDMI_PHY_SERCKCTRL, field TX_SER_CLK_EN2[0] (RW)
 *
 * Transmitter Serializer Clock Enable 2 This bit enables or disables the high-speed clock in
 * serializer two.
 *
 * Values:
 * - 0 - Disable the high-speed clock in the third serializer, if the Override bit is 0.
 * - 1 - Enable the high-speed clock in the third serializer, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2      (0)      //!< Bit position for HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2.
#define BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2      (0x00000001)  //!< Bit mask for HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2.

//! @brief Get value of HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2 from a register value.
#define BG_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2) >> BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2)

//! @brief Format value for bitfield HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2.
#define BF_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2) & BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN2)
//@}

/*! @name Register HDMI_PHY_SERCKCTRL, field TX_SER_CLK_EN1[1] (RW)
 *
 * Transmitter Serializer Clock Enable 1 This bit enables or disables the high-speed clock in
 * serializer 1.
 *
 * Values:
 * - 0 - Disable the high-speed clock in the second serializer, if the Override bit is 0.
 * - 1 - Enable the high-speed clock in the second serializer, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1      (1)      //!< Bit position for HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1.
#define BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1      (0x00000002)  //!< Bit mask for HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1.

//! @brief Get value of HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1 from a register value.
#define BG_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1) >> BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1)

//! @brief Format value for bitfield HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1.
#define BF_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1) & BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN1)
//@}

/*! @name Register HDMI_PHY_SERCKCTRL, field TX_SER_CLK_EN0[2] (RW)
 *
 * Transmitter Serializer Clock Enable 0 This bit enables or disables the high-speed clock in
 * serializer 0.
 *
 * Values:
 * - 0 - Disable the high-speed clock in the first serializer, if the Override bit is 0.
 * - 1 - Enable the high-speed clock in the first serializer, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0      (2)      //!< Bit position for HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0.
#define BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0      (0x00000004)  //!< Bit mask for HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0.

//! @brief Get value of HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0 from a register value.
#define BG_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0) >> BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0)

//! @brief Format value for bitfield HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0.
#define BF_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0) & BM_HDMI_PHY_SERCKCTRL_TX_SER_CLK_EN0)
//@}

/*! @name Register HDMI_PHY_SERCKCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_SERCKCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_SERCKCTRL_OVERRIDE.
#define BM_HDMI_PHY_SERCKCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_SERCKCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_SERCKCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_SERCKCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKCTRL_OVERRIDE) >> BP_HDMI_PHY_SERCKCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_SERCKCTRL_OVERRIDE.
#define BF_HDMI_PHY_SERCKCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKCTRL_OVERRIDE) & BM_HDMI_PHY_SERCKCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SERCKKILLCTRL - Serializer Clock Kill Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SERCKKILLCTRL - Serializer Clock Kill Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : SERCKKILLCTRL Access type : Read/write/override Address : 0x03 Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_serckkillctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_serckkillctrl_bitfields
    {
        unsigned short TX_SER_CLK_KILL2 : 1; //!< [0] Transmitter Serializer Clock Kill 2
        unsigned short TX_SER_CLK_KILL1 : 1; //!< [1] Transmitter Serializer Clock Kill 1
        unsigned short TX_SER_CLK_KILL0 : 1; //!< [2] Transmitter Serializer Clock Kill 0
        unsigned short RESERVED0 : 12; //!< [14:3] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_serckkillctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SERCKKILLCTRL register
 */
//@{
#define HW_HDMI_PHY_SERCKKILLCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x3)
//@}

/*
 * constants & macros for individual HDMI_PHY_SERCKKILLCTRL bitfields
 */

/*! @name Register HDMI_PHY_SERCKKILLCTRL, field TX_SER_CLK_KILL2[0] (RW)
 *
 * Transmitter Serializer Clock Kill 2 This bit is used to delay the tx_ck_out2 sampling clock by a
 * time t delay , where t delay equals one period of refclk (340 MHz). This delay equals 0.2 UI of
 * the tx_ck_out2 clock.
 *
 * Values:
 * - 0 - No effect, if the Override bit is 0.
 * - 1 - Delay the tx_ck_out2 clock by 0.2 UI, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2      (0)      //!< Bit position for HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2.
#define BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2      (0x00000001)  //!< Bit mask for HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2.

//! @brief Get value of HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2 from a register value.
#define BG_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2) >> BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2)

//! @brief Format value for bitfield HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2.
#define BF_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2) & BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL2)
//@}

/*! @name Register HDMI_PHY_SERCKKILLCTRL, field TX_SER_CLK_KILL1[1] (RW)
 *
 * Transmitter Serializer Clock Kill 1 This bit is used to delay the tx_ck_out1 sampling clock by a
 * time t delay , where t delay equals one period of refclk (340 MHz). This delay equals 0.2 UI of
 * the tx_ck_out1 clock.
 *
 * Values:
 * - 0 - No effect, if the Override bit is 0.
 * - 1 - Delay the tx_ck_out1 clock by 0.2 UI, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1      (1)      //!< Bit position for HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1.
#define BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1      (0x00000002)  //!< Bit mask for HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1.

//! @brief Get value of HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1 from a register value.
#define BG_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1) >> BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1)

//! @brief Format value for bitfield HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1.
#define BF_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1) & BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL1)
//@}

/*! @name Register HDMI_PHY_SERCKKILLCTRL, field TX_SER_CLK_KILL0[2] (RW)
 *
 * Transmitter Serializer Clock Kill 0 This bit is used to delay the tx_ck_out0 sampling clock by a
 * time t delay , where t delay equals one period of refclk (340 MHz). This delay equals 0.2 UI of
 * the tx_ck_out0 clock.
 *
 * Values:
 * - 0 - No effect, if the Override bit is 0.
 * - 1 - Delay the tx_ck_out0 clock by 0.2 UI, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0      (2)      //!< Bit position for HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0.
#define BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0      (0x00000004)  //!< Bit mask for HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0.

//! @brief Get value of HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0 from a register value.
#define BG_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0) >> BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0)

//! @brief Format value for bitfield HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0.
#define BF_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0) & BM_HDMI_PHY_SERCKKILLCTRL_TX_SER_CLK_KILL0)
//@}

/*! @name Register HDMI_PHY_SERCKKILLCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_SERCKKILLCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_SERCKKILLCTRL_OVERRIDE.
#define BM_HDMI_PHY_SERCKKILLCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_SERCKKILLCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_SERCKKILLCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_SERCKKILLCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SERCKKILLCTRL_OVERRIDE) >> BP_HDMI_PHY_SERCKKILLCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_SERCKKILLCTRL_OVERRIDE.
#define BF_HDMI_PHY_SERCKKILLCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SERCKKILLCTRL_OVERRIDE) & BM_HDMI_PHY_SERCKKILLCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_TXRESCTRL - Transmitter and Resistance Calibration Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_TXRESCTRL - Transmitter and Resistance Calibration Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : TXRESCALCTRL Access type : Read/write/override Address : 0x04 Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_txresctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_txresctrl_bitfields
    {
        unsigned short RESCAL_REP : 7; //!< [6:0] Resistance Calibration Replica
        unsigned short TX_RESCAL : 7; //!< [13:7] Transmitter Resistance Calibration
        unsigned short RESERVED0 : 1; //!< [14] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_txresctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_TXRESCTRL register
 */
//@{
#define HW_HDMI_PHY_TXRESCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x4)
//@}

/*
 * constants & macros for individual HDMI_PHY_TXRESCTRL bitfields
 */

/*! @name Register HDMI_PHY_TXRESCTRL, field RESCAL_REP[6:0] (RW)
 *
 * Resistance Calibration Replica This bus controls the bias voltage of the transmitter driver.
 * rescal_rep[6:0] provides 64 voltage levels; the specific values are defined from lab test
 * results.
 */
//@{
#define BP_HDMI_PHY_TXRESCTRL_RESCAL_REP      (0)      //!< Bit position for HDMI_PHY_TXRESCTRL_RESCAL_REP.
#define BM_HDMI_PHY_TXRESCTRL_RESCAL_REP      (0x0000007f)  //!< Bit mask for HDMI_PHY_TXRESCTRL_RESCAL_REP.

//! @brief Get value of HDMI_PHY_TXRESCTRL_RESCAL_REP from a register value.
#define BG_HDMI_PHY_TXRESCTRL_RESCAL_REP(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXRESCTRL_RESCAL_REP) >> BP_HDMI_PHY_TXRESCTRL_RESCAL_REP)

//! @brief Format value for bitfield HDMI_PHY_TXRESCTRL_RESCAL_REP.
#define BF_HDMI_PHY_TXRESCTRL_RESCAL_REP(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXRESCTRL_RESCAL_REP) & BM_HDMI_PHY_TXRESCTRL_RESCAL_REP)
//@}

/*! @name Register HDMI_PHY_TXRESCTRL, field TX_RESCAL[13:7] (RW)
 *
 * Transmitter Resistance Calibration This bus controls the parallel termination of the transmitter
 * drivers and sets termination to a value based on the calibration algorithm performed in the
 * support resistance calibration module. tx_rescal[6:0] provides 64 termination levels; the
 * specific values are defined from lab test results.
 */
//@{
#define BP_HDMI_PHY_TXRESCTRL_TX_RESCAL      (7)      //!< Bit position for HDMI_PHY_TXRESCTRL_TX_RESCAL.
#define BM_HDMI_PHY_TXRESCTRL_TX_RESCAL      (0x00003f80)  //!< Bit mask for HDMI_PHY_TXRESCTRL_TX_RESCAL.

//! @brief Get value of HDMI_PHY_TXRESCTRL_TX_RESCAL from a register value.
#define BG_HDMI_PHY_TXRESCTRL_TX_RESCAL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXRESCTRL_TX_RESCAL) >> BP_HDMI_PHY_TXRESCTRL_TX_RESCAL)

//! @brief Format value for bitfield HDMI_PHY_TXRESCTRL_TX_RESCAL.
#define BF_HDMI_PHY_TXRESCTRL_TX_RESCAL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXRESCTRL_TX_RESCAL) & BM_HDMI_PHY_TXRESCTRL_TX_RESCAL)
//@}

/*! @name Register HDMI_PHY_TXRESCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_TXRESCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_TXRESCTRL_OVERRIDE.
#define BM_HDMI_PHY_TXRESCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_TXRESCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_TXRESCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_TXRESCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXRESCTRL_OVERRIDE) >> BP_HDMI_PHY_TXRESCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_TXRESCTRL_OVERRIDE.
#define BF_HDMI_PHY_TXRESCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXRESCTRL_OVERRIDE) & BM_HDMI_PHY_TXRESCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CKCALCTRL - Clock Calibration Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CKCALCTRL - Clock Calibration Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : CKCALCTRL Access type : Read/write/override Address : 0x05 Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_ckcalctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_ckcalctrl_bitfields
    {
        unsigned short CK_RESCAL : 7; //!< [6:0] Clock Resistance Calibration
        unsigned short RESERVED0 : 8; //!< [14:7] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_ckcalctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CKCALCTRL register
 */
//@{
#define HW_HDMI_PHY_CKCALCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x5)
//@}

/*
 * constants & macros for individual HDMI_PHY_CKCALCTRL bitfields
 */

/*! @name Register HDMI_PHY_CKCALCTRL, field CK_RESCAL[6:0] (RW)
 *
 * Clock Resistance Calibration This bus controls the termination of the clock driver and sets the
 * termination to a value based on the calibration algorithm performed in the support resistance
 * calibration module. ck_rescal[6:0] provides 64 termination levels; the specific values are
 * defined from lab test results.
 */
//@{
#define BP_HDMI_PHY_CKCALCTRL_CK_RESCAL      (0)      //!< Bit position for HDMI_PHY_CKCALCTRL_CK_RESCAL.
#define BM_HDMI_PHY_CKCALCTRL_CK_RESCAL      (0x0000007f)  //!< Bit mask for HDMI_PHY_CKCALCTRL_CK_RESCAL.

//! @brief Get value of HDMI_PHY_CKCALCTRL_CK_RESCAL from a register value.
#define BG_HDMI_PHY_CKCALCTRL_CK_RESCAL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKCALCTRL_CK_RESCAL) >> BP_HDMI_PHY_CKCALCTRL_CK_RESCAL)

//! @brief Format value for bitfield HDMI_PHY_CKCALCTRL_CK_RESCAL.
#define BF_HDMI_PHY_CKCALCTRL_CK_RESCAL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKCALCTRL_CK_RESCAL) & BM_HDMI_PHY_CKCALCTRL_CK_RESCAL)
//@}

/*! @name Register HDMI_PHY_CKCALCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_CKCALCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_CKCALCTRL_OVERRIDE.
#define BM_HDMI_PHY_CKCALCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_CKCALCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_CKCALCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_CKCALCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKCALCTRL_OVERRIDE) >> BP_HDMI_PHY_CKCALCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_CKCALCTRL_OVERRIDE.
#define BF_HDMI_PHY_CKCALCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKCALCTRL_OVERRIDE) & BM_HDMI_PHY_CKCALCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CPCE_CTRL - Color Depth, Pixel Repetition, Clock Divider for PLL and MPLL, and Edge Rate Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CPCE_CTRL - Color Depth, Pixel Repetition, Clock Divider for PLL and MPLL, and Edge Rate Control (RW)
 *
 * Reset value: 0x0400
 *
 * Register name : - Access type : Read/write Address : 0x06 Value at reset : 0x0400
 */
typedef union _hw_hdmi_phy_cpce_ctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_cpce_ctrl_bitfields
    {
        unsigned short CLR_DPTH : 2; //!< [1:0] Color Depth
        unsigned short PIXEL_REP : 3; //!< [4:2] Pixel Repetition
        unsigned short PLL_N_CNTRL : 2; //!< [6:5] Programmable Divider Control
        unsigned short MPLL_N_CNTRL : 2; //!< [8:7] Programmable Divider Control
        unsigned short CK_EDGERATE : 2; //!< [10:9] Clock Edge Rate
        unsigned short TX_EDGERATE : 2; //!< [12:11] Transmitter Edge Rate
        unsigned short PREP_DIV : 2; //!< [14:13] Digital Pixel Repetition Divider Controls the ratio by which the internal TMDS clock is divided to generate PREPCLK.
        unsigned short RESERVED0 : 1; //!< [15] Reserved
    } B;
} hw_hdmi_phy_cpce_ctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CPCE_CTRL register
 */
//@{
#define HW_HDMI_PHY_CPCE_CTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x6)
//@}

/*
 * constants & macros for individual HDMI_PHY_CPCE_CTRL bitfields
 */

/*! @name Register HDMI_PHY_CPCE_CTRL, field CLR_DPTH[1:0] (RW)
 *
 * Color Depth This bus controls the factor by which to divide the reference clock (PCLK) by the
 * output TMDS rate (ck_ref_mpll_p/m).
 *
 * Values:
 * - 00 - Divide by 4.
 * - 01 - Divide by 5.
 * - 10 - Divide by 6.
 * - 11 - Divide by 8.
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_CLR_DPTH      (0)      //!< Bit position for HDMI_PHY_CPCE_CTRL_CLR_DPTH.
#define BM_HDMI_PHY_CPCE_CTRL_CLR_DPTH      (0x00000003)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_CLR_DPTH.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_CLR_DPTH from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_CLR_DPTH(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_CLR_DPTH) >> BP_HDMI_PHY_CPCE_CTRL_CLR_DPTH)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_CLR_DPTH.
#define BF_HDMI_PHY_CPCE_CTRL_CLR_DPTH(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_CLR_DPTH) & BM_HDMI_PHY_CPCE_CTRL_CLR_DPTH)
//@}

/*! @name Register HDMI_PHY_CPCE_CTRL, field PIXEL_REP[4:2] (RW)
 *
 * Pixel Repetition This bus controls another factor by which to divide the input frequency (refclk)
 * by the output TMDS rate (ck_ref_mpll_p/m). FTMDS/Fin = (clr_depth[1:0] x pixel_rep[2]) /
 * (pixel_rep[1:0])
 *
 * Values:
 * - 0 - Pixel_rep[2] Divide by 1.
 * - 00 - Pixel_rep[1:0] Divide by 4.
 * - 1 - Pixel_rep[2] Divide by 2.
 * - 01 - Pixel_rep[1:0] Divide by 2.
 * - 1x - Pixel_rep[1:0] Divide by 1.
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_PIXEL_REP      (2)      //!< Bit position for HDMI_PHY_CPCE_CTRL_PIXEL_REP.
#define BM_HDMI_PHY_CPCE_CTRL_PIXEL_REP      (0x0000001c)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_PIXEL_REP.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_PIXEL_REP from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_PIXEL_REP(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_PIXEL_REP) >> BP_HDMI_PHY_CPCE_CTRL_PIXEL_REP)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_PIXEL_REP.
#define BF_HDMI_PHY_CPCE_CTRL_PIXEL_REP(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_PIXEL_REP) & BM_HDMI_PHY_CPCE_CTRL_PIXEL_REP)
//@}

/*! @name Register HDMI_PHY_CPCE_CTRL, field PLL_N_CNTRL[6:5] (RW)
 *
 * Programmable Divider Control This bus controls the programmable divider modules, which are set
 * based on the refclk_p/m (pixel rate) input reference frequency to keep the ring oscillator within
 * the required range (740 MHz through 1.48 GHz in PLL).
 *
 * Values:
 * - 00 - N = 1 (for TMDS rate of 184.1-370 MHz)
 * - 01 - N = 2 (for TMDS rate of 92.51-185 MHz)
 * - 10 - N = 4 (for TMDS rate of 45.26-92.5 MHz)
 * - 11 - N = 8 (for TMDS rate (not the pixel rate) up to 45.25 MHz)
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL      (5)      //!< Bit position for HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL.
#define BM_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL      (0x00000060)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL) >> BP_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL.
#define BF_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL) & BM_HDMI_PHY_CPCE_CTRL_PLL_N_CNTRL)
//@}

/*! @name Register HDMI_PHY_CPCE_CTRL, field MPLL_N_CNTRL[8:7] (RW)
 *
 * Programmable Divider Control This bus controls the programmable divider modulus, which are set
 * based on the ck_ref_mpll_p/m (TMDS rate) input reference frequency to keep the ring oscillator
 * within the required range (925 MHz through 1.85 GHz in MPLL).
 *
 * Values:
 * - 00 - N = 1 (for TMDS rate of 184.1-370 MHz)
 * - 01 - N = 2 (for TMDS rate of 92.51-185 MHz)
 * - 10 - N = 4 (for TMDS rate of 45.26-92.5 MHz)
 * - 11 - N = 8 (for TMDS rate up to 45.25 MHz)
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL      (7)      //!< Bit position for HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL.
#define BM_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL      (0x00000180)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL) >> BP_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL.
#define BF_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL) & BM_HDMI_PHY_CPCE_CTRL_MPLL_N_CNTRL)
//@}

/*! @name Register HDMI_PHY_CPCE_CTRL, field CK_EDGERATE[10:9] (RW)
 *
 * Clock Edge Rate This bus controls the slew rate of the clock output driver.
 *
 * Values:
 * - 0 - ck_edgerate[0]: Slow edges
 * - 0 - ck_edgerate[1]: Disable edge rate override.
 * - 1 - ck_edgerate[0]: Fast edges
 * - 1 - ck_edgerate[1]: Enable edge rate override.
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_CK_EDGERATE      (9)      //!< Bit position for HDMI_PHY_CPCE_CTRL_CK_EDGERATE.
#define BM_HDMI_PHY_CPCE_CTRL_CK_EDGERATE      (0x00000600)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_CK_EDGERATE.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_CK_EDGERATE from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_CK_EDGERATE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_CK_EDGERATE) >> BP_HDMI_PHY_CPCE_CTRL_CK_EDGERATE)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_CK_EDGERATE.
#define BF_HDMI_PHY_CPCE_CTRL_CK_EDGERATE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_CK_EDGERATE) & BM_HDMI_PHY_CPCE_CTRL_CK_EDGERATE)
//@}

/*! @name Register HDMI_PHY_CPCE_CTRL, field TX_EDGERATE[12:11] (RW)
 *
 * Transmitter Edge Rate This bus controls the slew rate of the transmitter output driver.
 *
 * Values:
 * - 0 - tx_edgerate[0]: Slow edges
 * - 0 - tx_edgerate[1]: Disable edge rate override.
 * - 1 - tx_edgerate[0]: Fast edges
 * - 1 - tx_edgerate[1]: Enable edge rate override.
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_TX_EDGERATE      (11)      //!< Bit position for HDMI_PHY_CPCE_CTRL_TX_EDGERATE.
#define BM_HDMI_PHY_CPCE_CTRL_TX_EDGERATE      (0x00001800)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_TX_EDGERATE.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_TX_EDGERATE from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_TX_EDGERATE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_TX_EDGERATE) >> BP_HDMI_PHY_CPCE_CTRL_TX_EDGERATE)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_TX_EDGERATE.
#define BF_HDMI_PHY_CPCE_CTRL_TX_EDGERATE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_TX_EDGERATE) & BM_HDMI_PHY_CPCE_CTRL_TX_EDGERATE)
//@}

/*! @name Register HDMI_PHY_CPCE_CTRL, field PREP_DIV[14:13] (RW)
 *
 * Digital Pixel Repetition Divider Controls the ratio by which the internal TMDS clock is divided
 * to generate PREPCLK.
 *
 * Values:
 * - 00 - Divide by 1 (8 bit).
 * - 01 - Divide by 1.25 (10 bits).
 * - 10 - Divide by 1.5 (12 bits).
 * - 11 - Divide by 2 (16 bits).
 */
//@{
#define BP_HDMI_PHY_CPCE_CTRL_PREP_DIV      (13)      //!< Bit position for HDMI_PHY_CPCE_CTRL_PREP_DIV.
#define BM_HDMI_PHY_CPCE_CTRL_PREP_DIV      (0x00006000)  //!< Bit mask for HDMI_PHY_CPCE_CTRL_PREP_DIV.

//! @brief Get value of HDMI_PHY_CPCE_CTRL_PREP_DIV from a register value.
#define BG_HDMI_PHY_CPCE_CTRL_PREP_DIV(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CPCE_CTRL_PREP_DIV) >> BP_HDMI_PHY_CPCE_CTRL_PREP_DIV)

//! @brief Format value for bitfield HDMI_PHY_CPCE_CTRL_PREP_DIV.
#define BF_HDMI_PHY_CPCE_CTRL_PREP_DIV(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CPCE_CTRL_PREP_DIV) & BM_HDMI_PHY_CPCE_CTRL_PREP_DIV)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_TXCLKMEASCTRL - Tx and Clock Measure Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_TXCLKMEASCTRL - Tx and Clock Measure Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : TXCKMEASCTRL Access type : Read/write Address : 0x07 Value at reset : 0x0000
 * tx_meas_iv2[7:0] Effective Bit Register Value Description tx_meas_iv2[0] 00000001 Connect V cm_p
 * (common DC voltage of the positive side of scope) to the analog test bus. tx_meas_iv2[1] 00000010
 * Connect V cm_m (common DC voltage of the negative side of scope) to the analog test bus.
 * tx_meas_iv2[2] 00000100 Connect V bg3by4_reg (output node of tx_vreg_vbgby2 block) to the analog
 * test bus. tx_meas_iv2[3] 00001000 Connect t x_vref (reference voltage of tx_biasgen block) to the
 * analog test bus. tx_meas_iv2[4] 00010000 Connect V rep_fb (feedback voltage of the replica
 * circuit of tx_biasgen block) to the analog test bus. tx_meas_iv2[5] 00100000 In the event that
 * bleed current is too large, this bit can be used to force vb closer to gnd and disable/reduce the
 * bleed current. (This bit is a debug feature, which does not pull vb to gnd properly.)
 * tx_meas_iv2[6] 01000000 Connect V p (low power supply) to the analog test bus. tx_meas_iv2[7]
 * 10000000 Connect V cm (common DC voltage of the scope) to the analog test bus. ck_meas_iv[7:0]
 * Effective Bit Register Value Description ck_meas_iv[0] 00000001 Connect V cm_p (common DC voltage
 * of the positive side of scope) to the analog test bus. ck_meas_iv[1] 00000010 Connect V cm_m
 * (common DC voltage of the negative side of scope) to the analog test bus. ck_meas_iv[2] 00000100
 * Connect V bg3by4_reg (output node of tx_vreg_vbgby2 block) to the analog test bus. ck_meas_iv[3]
 * 00001000 Connect t x_vref (reference voltage of tx_biasgen block) to the analog test bus.
 * ck_meas_iv[4] 00010000 Connect V rep_fb (feedback voltage of the replica circuit of tx_biasgen
 * block) to the analog test bus. ck_meas_iv[5] 00100000 In the event that bleed current is too
 * large, this bit can be used to force v b closer to gnd and disable/reduce the bleed current.
 * (This bit is a debug feature, which does not pull v b to gnd properly.) ck_meas_iv[6] 01000000
 * Connect V p (low power supply) to the analog test bus. ck_meas_iv[7] 10000000 Connect V cm
 * (common DC voltage of scope) to the analog test bus.
 */
typedef union _hw_hdmi_phy_txclkmeasctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_txclkmeasctrl_bitfields
    {
        unsigned short CK_MEAS_IV : 8; //!< [7:0] Clock Measure Internal Voltage
        unsigned short TX_MEAS_IV2 : 8; //!< [15:8] Transmitter Measure Internal Voltage 2
    } B;
} hw_hdmi_phy_txclkmeasctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_TXCLKMEASCTRL register
 */
//@{
#define HW_HDMI_PHY_TXCLKMEASCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x7)
//@}

/*
 * constants & macros for individual HDMI_PHY_TXCLKMEASCTRL bitfields
 */

/*! @name Register HDMI_PHY_TXCLKMEASCTRL, field CK_MEAS_IV[7:0] (RW)
 *
 * Clock Measure Internal Voltage This bus is used to test specific voltages for the clock
 * lane/channel by applying voltages on the atb_sense port based on configured currents, as
 * described in the ck_meas_iv[7:0] table.
 */
//@{
#define BP_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV      (0)      //!< Bit position for HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV.
#define BM_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV      (0x000000ff)  //!< Bit mask for HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV.

//! @brief Get value of HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV from a register value.
#define BG_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV) >> BP_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV)

//! @brief Format value for bitfield HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV.
#define BF_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV) & BM_HDMI_PHY_TXCLKMEASCTRL_CK_MEAS_IV)
//@}

/*! @name Register HDMI_PHY_TXCLKMEASCTRL, field TX_MEAS_IV2[15:8] (RW)
 *
 * Transmitter Measure Internal Voltage 2 This bus is used to test specific voltages for third
 * transmitter lane/channel by applying voltages on the atb_sense port based on configured currents,
 * as described in the tx_meas_iv2[7:0] table.
 */
//@{
#define BP_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2      (8)      //!< Bit position for HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2.
#define BM_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2      (0x0000ff00)  //!< Bit mask for HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2.

//! @brief Get value of HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2 from a register value.
#define BG_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2) >> BP_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2)

//! @brief Format value for bitfield HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2.
#define BF_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2) & BM_HDMI_PHY_TXCLKMEASCTRL_TX_MEAS_IV2)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_TXMEASCTRL - Tx Measure Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_TXMEASCTRL - Tx Measure Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : TXMEASCTRL Access type : Read/write Address : 0x08 Value at reset : 0x0000
 * tx_meas_iv1[7:0] Effective Bit Register Value Description tx_meas_iv1[0] 00000001 Connect V cm_p
 * (common DC voltage of positive side of scope) to the analog test bus. tx_meas_iv1[1] 00000010
 * Connect V cm_m (common DC voltage of negative side of scope) to the analog test bus.
 * tx_meas_iv1[2] 00000100 Connect V bg3by4_reg (output node of tx_vreg_vbgby2 block) to the analog
 * test bus. tx_meas_iv1[3] 00001000 Connect t x_vref (reference voltage of tx_biasgen block) to the
 * analog test bus. tx_meas_iv1[4] 00010000 Connect V rep_fb (feedback voltage of replica circuit of
 * tx_biasgen block) to the analog test bus. tx_meas_iv1[5] 00100000 In case bleed current is too
 * large, this bit can be used to force v b closer to gnd and disable/reduce the bleed current.
 * (This bit is a debug feature, which does not pull v b to gnd properly.) tx_meas_iv1[6] 01000000
 * Connect V p (low power supply) to the analog test bus. tx_meas_iv1[7] 10000000 Connect V cm
 * (common DC voltage of scope) to the analog test bus. tx_meas_iv0[7:0] Effective Bit Register
 * Value Description tx_meas_iv0[0] 00000001 Connect V cm_p (common DC voltage of positive side of
 * scope) to the analog test bus. tx_meas_iv0[1] 00000010 Connect V cm_m (common DC voltage of
 * negative side of scope) to the analog test bus. tx_meas_iv0[2] 00000100 Connect V bg3by4_reg
 * (output node of tx_vreg_vbgby2 block) to the analog test bus. tx_meas_iv0[3] 00001000 Connect t
 * x_vref (reference voltage of tx_biasgen block) to the analog test bus tx_meas_iv0[4] 00010000
 * Connect V rep_fb (feedback voltage of replica circuit of tx_biasgen block) to the analog test
 * bus. tx_meas_iv0[5] 00100000 In the event that bleed current is too large, this bit can be used
 * to force v b closer to gnd and disable/reduce the bleed current. (This bit is a debug feature,
 * which does not pull v b to gnd properly.) tx_meas_iv0[6] 01000000 Connect V p (low power supply)
 * to the analog test bus. tx_meas_iv0[7] 10000000 Connect V cm (common DC voltage of scope) to the
 * analog test bus.
 */
typedef union _hw_hdmi_phy_txmeasctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_txmeasctrl_bitfields
    {
        unsigned short TX_MEAS_IV1 : 8; //!< [7:0] Transmitter Measure Internal Voltage 1
        unsigned short TX_MEAS_IV0 : 8; //!< [15:8] Transmitter Measure Internal Voltage 0
    } B;
} hw_hdmi_phy_txmeasctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_TXMEASCTRL register
 */
//@{
#define HW_HDMI_PHY_TXMEASCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x8)
//@}

/*
 * constants & macros for individual HDMI_PHY_TXMEASCTRL bitfields
 */

/*! @name Register HDMI_PHY_TXMEASCTRL, field TX_MEAS_IV1[7:0] (RW)
 *
 * Transmitter Measure Internal Voltage 1 This bus is used to test specific voltages for the second
 * transmitter lane/channel by applying voltages on the atb_sense port based on configured currents,
 * as described in the tx_meas_iv1[7:0] table.
 */
//@{
#define BP_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1      (0)      //!< Bit position for HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1.
#define BM_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1      (0x000000ff)  //!< Bit mask for HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1.

//! @brief Get value of HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1 from a register value.
#define BG_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1) >> BP_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1)

//! @brief Format value for bitfield HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1.
#define BF_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1) & BM_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV1)
//@}

/*! @name Register HDMI_PHY_TXMEASCTRL, field TX_MEAS_IV0[15:8] (RW)
 *
 * Transmitter Measure Internal Voltage 0 This bus is used to test specific voltages for the first
 * transmitter lane/channel by applying voltages on the atb_sense port based on configured currents,
 * as described in the tx_meas_iv0[7:0] table.
 */
//@{
#define BP_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0      (8)      //!< Bit position for HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0.
#define BM_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0      (0x0000ff00)  //!< Bit mask for HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0.

//! @brief Get value of HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0 from a register value.
#define BG_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0) >> BP_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0)

//! @brief Format value for bitfield HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0.
#define BF_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0) & BM_HDMI_PHY_TXMEASCTRL_TX_MEAS_IV0)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CKSYMTXCTRL - Clock Symbol and Transmitter Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CKSYMTXCTRL - Clock Symbol and Transmitter Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : CKSYMTXCTRL Access type : Read/write/override Address : 0x09 Value at reset :
 * 0x0009
 */
typedef union _hw_hdmi_phy_cksymtxctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_cksymtxctrl_bitfields
    {
        unsigned short CK_SYMON : 1; //!< [0] Clock Symbol On
        unsigned short TX_TRBON : 1; //!< [1] Transmitter Trailer B On
        unsigned short TX_TRAON : 1; //!< [2] Transmitter Trailer A On
        unsigned short TX_SYMON : 1; //!< [3] Transmitter Symbol On
        unsigned short RESERVED0 : 11; //!< [14:4] Reserved
        unsigned short OVERRIDE : 1; //!< [15] 
    } B;
} hw_hdmi_phy_cksymtxctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CKSYMTXCTRL register
 */
//@{
#define HW_HDMI_PHY_CKSYMTXCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x9)
//@}

/*
 * constants & macros for individual HDMI_PHY_CKSYMTXCTRL bitfields
 */

/*! @name Register HDMI_PHY_CKSYMTXCTRL, field CK_SYMON[0] (RW)
 *
 * Clock Symbol On This bit enables the clock symbol driver. To enable the clock driver, the
 * ck_powon bit must be high. In addition, there is no pre-emphasis enable for the clock driver.
 *
 * Values:
 * - 0 - Disable the clock symbol driver, if the Override bit is 0.
 * - 1 - Enable the clock symbol driver, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_CKSYMTXCTRL_CK_SYMON      (0)      //!< Bit position for HDMI_PHY_CKSYMTXCTRL_CK_SYMON.
#define BM_HDMI_PHY_CKSYMTXCTRL_CK_SYMON      (0x00000001)  //!< Bit mask for HDMI_PHY_CKSYMTXCTRL_CK_SYMON.

//! @brief Get value of HDMI_PHY_CKSYMTXCTRL_CK_SYMON from a register value.
#define BG_HDMI_PHY_CKSYMTXCTRL_CK_SYMON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKSYMTXCTRL_CK_SYMON) >> BP_HDMI_PHY_CKSYMTXCTRL_CK_SYMON)

//! @brief Format value for bitfield HDMI_PHY_CKSYMTXCTRL_CK_SYMON.
#define BF_HDMI_PHY_CKSYMTXCTRL_CK_SYMON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKSYMTXCTRL_CK_SYMON) & BM_HDMI_PHY_CKSYMTXCTRL_CK_SYMON)
//@}

/*! @name Register HDMI_PHY_CKSYMTXCTRL, field TX_TRBON[1] (RW)
 *
 * Transmitter Trailer B On This bit enables the transmitter trailer B driver(s). To enable the
 * transmitter trailer B driver(s) and to enable pre-emphasis, the tx_pwron bit for each channel
 * must be high.
 *
 * Values:
 * - 0 - Disable the transmitter trailer B driver(s), if the Override bit is 0.
 * - 1 - Enable the transmitter trailer B driver(s), if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_CKSYMTXCTRL_TX_TRBON      (1)      //!< Bit position for HDMI_PHY_CKSYMTXCTRL_TX_TRBON.
#define BM_HDMI_PHY_CKSYMTXCTRL_TX_TRBON      (0x00000002)  //!< Bit mask for HDMI_PHY_CKSYMTXCTRL_TX_TRBON.

//! @brief Get value of HDMI_PHY_CKSYMTXCTRL_TX_TRBON from a register value.
#define BG_HDMI_PHY_CKSYMTXCTRL_TX_TRBON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKSYMTXCTRL_TX_TRBON) >> BP_HDMI_PHY_CKSYMTXCTRL_TX_TRBON)

//! @brief Format value for bitfield HDMI_PHY_CKSYMTXCTRL_TX_TRBON.
#define BF_HDMI_PHY_CKSYMTXCTRL_TX_TRBON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKSYMTXCTRL_TX_TRBON) & BM_HDMI_PHY_CKSYMTXCTRL_TX_TRBON)
//@}

/*! @name Register HDMI_PHY_CKSYMTXCTRL, field TX_TRAON[2] (RW)
 *
 * Transmitter Trailer A On This bit enables the transmitter trailer A driver(s). To enable the
 * transmitter trailer A driver(s) and to enable pre-emphasis, the tx_pwron bit for each channel
 * must be high.
 *
 * Values:
 * - 0 - Disable the transmitter trailer A driver(s), if the Override bit is 0.
 * - 1 - Enable the transmitter trailer A driver(s), if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_CKSYMTXCTRL_TX_TRAON      (2)      //!< Bit position for HDMI_PHY_CKSYMTXCTRL_TX_TRAON.
#define BM_HDMI_PHY_CKSYMTXCTRL_TX_TRAON      (0x00000004)  //!< Bit mask for HDMI_PHY_CKSYMTXCTRL_TX_TRAON.

//! @brief Get value of HDMI_PHY_CKSYMTXCTRL_TX_TRAON from a register value.
#define BG_HDMI_PHY_CKSYMTXCTRL_TX_TRAON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKSYMTXCTRL_TX_TRAON) >> BP_HDMI_PHY_CKSYMTXCTRL_TX_TRAON)

//! @brief Format value for bitfield HDMI_PHY_CKSYMTXCTRL_TX_TRAON.
#define BF_HDMI_PHY_CKSYMTXCTRL_TX_TRAON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKSYMTXCTRL_TX_TRAON) & BM_HDMI_PHY_CKSYMTXCTRL_TX_TRAON)
//@}

/*! @name Register HDMI_PHY_CKSYMTXCTRL, field TX_SYMON[3] (RW)
 *
 * Transmitter Symbol On This bit enables the transmitter symbol driver(s), To enable the
 * transmitter driver(s), the tx_pwron bit for each channel must be high.
 *
 * Values:
 * - 0 - Disable the transmitter symbol driver(s), if the Override bit is 0.
 * - 1 - Enable the transmitter symbol driver(s), if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_CKSYMTXCTRL_TX_SYMON      (3)      //!< Bit position for HDMI_PHY_CKSYMTXCTRL_TX_SYMON.
#define BM_HDMI_PHY_CKSYMTXCTRL_TX_SYMON      (0x00000008)  //!< Bit mask for HDMI_PHY_CKSYMTXCTRL_TX_SYMON.

//! @brief Get value of HDMI_PHY_CKSYMTXCTRL_TX_SYMON from a register value.
#define BG_HDMI_PHY_CKSYMTXCTRL_TX_SYMON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKSYMTXCTRL_TX_SYMON) >> BP_HDMI_PHY_CKSYMTXCTRL_TX_SYMON)

//! @brief Format value for bitfield HDMI_PHY_CKSYMTXCTRL_TX_SYMON.
#define BF_HDMI_PHY_CKSYMTXCTRL_TX_SYMON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKSYMTXCTRL_TX_SYMON) & BM_HDMI_PHY_CKSYMTXCTRL_TX_SYMON)
//@}

/*! @name Register HDMI_PHY_CKSYMTXCTRL, field OVERRIDE[15] (RW)
 */
//@{
#define BP_HDMI_PHY_CKSYMTXCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_CKSYMTXCTRL_OVERRIDE.
#define BM_HDMI_PHY_CKSYMTXCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_CKSYMTXCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_CKSYMTXCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_CKSYMTXCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CKSYMTXCTRL_OVERRIDE) >> BP_HDMI_PHY_CKSYMTXCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_CKSYMTXCTRL_OVERRIDE.
#define BF_HDMI_PHY_CKSYMTXCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CKSYMTXCTRL_OVERRIDE) & BM_HDMI_PHY_CKSYMTXCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CMPSEQCTRL - Comparator Sequence Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CMPSEQCTRL - Comparator Sequence Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : CMPSEQCTRL Access type : Read/write/override Address : 0x0A Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_cmpseqctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_cmpseqctrl_bitfields
    {
        unsigned short SUP_COMP_RT_R : 1; //!< [0] Support Comparator Resistance Termination
        unsigned short RESERVED0 : 14; //!< [14:1] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_cmpseqctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CMPSEQCTRL register
 */
//@{
#define HW_HDMI_PHY_CMPSEQCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0xa)
//@}

/*
 * constants & macros for individual HDMI_PHY_CMPSEQCTRL bitfields
 */

/*! @name Register HDMI_PHY_CMPSEQCTRL, field SUP_COMP_RT_R[0] (RW)
 *
 * Support Comparator Resistance Termination This bit controls the comparator sequence.
 *
 * Values:
 * - 0 - Latch the first input, if the Override bit is 0.
 * - 1 - Latch the second input, then set the comparator's output pin by the result of comparison, if the
 *     Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R      (0)      //!< Bit position for HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R.
#define BM_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R      (0x00000001)  //!< Bit mask for HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R.

//! @brief Get value of HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R from a register value.
#define BG_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R) >> BP_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R)

//! @brief Format value for bitfield HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R.
#define BF_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R) & BM_HDMI_PHY_CMPSEQCTRL_SUP_COMP_RT_R)
//@}

/*! @name Register HDMI_PHY_CMPSEQCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_CMPSEQCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_CMPSEQCTRL_OVERRIDE.
#define BM_HDMI_PHY_CMPSEQCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_CMPSEQCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_CMPSEQCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_CMPSEQCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CMPSEQCTRL_OVERRIDE) >> BP_HDMI_PHY_CMPSEQCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_CMPSEQCTRL_OVERRIDE.
#define BF_HDMI_PHY_CMPSEQCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CMPSEQCTRL_OVERRIDE) & BM_HDMI_PHY_CMPSEQCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CMPPWRCTRL - Comparator Power Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CMPPWRCTRL - Comparator Power Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : CMPPWRCTRL Access type : Read/write/override Address : 0x0B Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_cmppwrctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_cmppwrctrl_bitfields
    {
        unsigned short SUP_COMP_RT_PWRON : 1; //!< [0] Support Comparator Resistance Termination Power-On
        unsigned short RESERVED0 : 14; //!< [14:1] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_cmppwrctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CMPPWRCTRL register
 */
//@{
#define HW_HDMI_PHY_CMPPWRCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0xb)
//@}

/*
 * constants & macros for individual HDMI_PHY_CMPPWRCTRL bitfields
 */

/*! @name Register HDMI_PHY_CMPPWRCTRL, field SUP_COMP_RT_PWRON[0] (RW)
 *
 * Support Comparator Resistance Termination Power-On This bit powers on the Comparator module.
 *
 * Values:
 * - 0 - Power off the Comparator module and connect the comparator's output to ground, if the Override bit
 *     is 0.
 * - 1 - Power on the Comparator module, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON      (0)      //!< Bit position for HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON.
#define BM_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON      (0x00000001)  //!< Bit mask for HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON.

//! @brief Get value of HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON from a register value.
#define BG_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON) >> BP_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON)

//! @brief Format value for bitfield HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON.
#define BF_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON) & BM_HDMI_PHY_CMPPWRCTRL_SUP_COMP_RT_PWRON)
//@}

/*! @name Register HDMI_PHY_CMPPWRCTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_CMPPWRCTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_CMPPWRCTRL_OVERRIDE.
#define BM_HDMI_PHY_CMPPWRCTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_CMPPWRCTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_CMPPWRCTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_CMPPWRCTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CMPPWRCTRL_OVERRIDE) >> BP_HDMI_PHY_CMPPWRCTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_CMPPWRCTRL_OVERRIDE.
#define BF_HDMI_PHY_CMPPWRCTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CMPPWRCTRL_OVERRIDE) & BM_HDMI_PHY_CMPPWRCTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CMPMODECTRL - Comparator Mode Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CMPMODECTRL - Comparator Mode Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : CMPMODECTRL Access type : Read/write/override Address : 0x0C Value at reset :
 * 0x0000
 */
typedef union _hw_hdmi_phy_cmpmodectrl
{
    reg16_t U;
    struct _hw_hdmi_phy_cmpmodectrl_bitfields
    {
        unsigned short SUP_COMP_MODE : 1; //!< [0] Support Comparator Mode
        unsigned short RESERVED0 : 14; //!< [14:1] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_cmpmodectrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CMPMODECTRL register
 */
//@{
#define HW_HDMI_PHY_CMPMODECTRL_ADDR      (REGS_HDMI_PHY_BASE + 0xc)
//@}

/*
 * constants & macros for individual HDMI_PHY_CMPMODECTRL bitfields
 */

/*! @name Register HDMI_PHY_CMPMODECTRL, field SUP_COMP_MODE[0] (RW)
 *
 * Support Comparator Mode This bit selects the comparator mode.
 *
 * Values:
 * - 0 - Testing mode (ADC mode)
 * - 1 - Calibration mode
 */
//@{
#define BP_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE      (0)      //!< Bit position for HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE.
#define BM_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE      (0x00000001)  //!< Bit mask for HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE.

//! @brief Get value of HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE from a register value.
#define BG_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE) >> BP_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE)

//! @brief Format value for bitfield HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE.
#define BF_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE) & BM_HDMI_PHY_CMPMODECTRL_SUP_COMP_MODE)
//@}

/*! @name Register HDMI_PHY_CMPMODECTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_CMPMODECTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_CMPMODECTRL_OVERRIDE.
#define BM_HDMI_PHY_CMPMODECTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_CMPMODECTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_CMPMODECTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_CMPMODECTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CMPMODECTRL_OVERRIDE) >> BP_HDMI_PHY_CMPMODECTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_CMPMODECTRL_OVERRIDE.
#define BF_HDMI_PHY_CMPMODECTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CMPMODECTRL_OVERRIDE) & BM_HDMI_PHY_CMPMODECTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_MEASCTRL - Measure Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_MEASCTRL - Measure Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : MEASCTRL Access type : Read/write Address : 0x0D Value at reset : 0x0000 Two or
 * more of the previous register bits must not be set to 1 simultaneously; doing so can lead to a
 * hardware problem.
 */
typedef union _hw_hdmi_phy_measctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_measctrl_bitfields
    {
        unsigned short SUP_DAC_ON_ATB : 1; //!< [0] Support Digital-to-Analog Converter On Analog Test Bus
        unsigned short SUP_POR_MEAS_IV : 2; //!< [2:1] Support Power Measure Internal Voltage
        unsigned short SUP_ATB_ON_REXT : 1; //!< [3] Support Analog Test Bus On External Calibration Resistance
        unsigned short RESERVED0 : 12; //!< [15:4] Reserved
    } B;
} hw_hdmi_phy_measctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_MEASCTRL register
 */
//@{
#define HW_HDMI_PHY_MEASCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0xd)
//@}

/*
 * constants & macros for individual HDMI_PHY_MEASCTRL bitfields
 */

/*! @name Register HDMI_PHY_MEASCTRL, field SUP_DAC_ON_ATB[0] (RW)
 *
 * Support Digital-to-Analog Converter On Analog Test Bus This bit connects or disconnects the DAC's
 * output on the analog test bus to test the performance of the DAC through Integral Non-Linearity
 * (INL) and Differential Non-Linearity (DNL).
 *
 * Values:
 * - 0 - Disconnect the DAC's output from the analog test bus.
 * - 1 - Connect the DAC's output to the analog test bus.
 */
//@{
#define BP_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB      (0)      //!< Bit position for HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB.
#define BM_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB      (0x00000001)  //!< Bit mask for HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB.

//! @brief Get value of HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB from a register value.
#define BG_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB) >> BP_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB)

//! @brief Format value for bitfield HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB.
#define BF_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB) & BM_HDMI_PHY_MEASCTRL_SUP_DAC_ON_ATB)
//@}

/*! @name Register HDMI_PHY_MEASCTRL, field SUP_POR_MEAS_IV[2:1] (RW)
 *
 * Support Power Measure Internal Voltage This bus connects or disconnects a single output signal on
 * the analog test bus to measure the voltage of two nodes of the support power block.
 *
 * Values:
 * - 01 - Connect V be (Bipolar transistor voltage) to the analog test bus.
 * - 10 - Connect V bg (Band-gap voltage) to the analog test bus.
 */
//@{
#define BP_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV      (1)      //!< Bit position for HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV.
#define BM_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV      (0x00000006)  //!< Bit mask for HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV.

//! @brief Get value of HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV from a register value.
#define BG_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV) >> BP_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV)

//! @brief Format value for bitfield HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV.
#define BF_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV) & BM_HDMI_PHY_MEASCTRL_SUP_POR_MEAS_IV)
//@}

/*! @name Register HDMI_PHY_MEASCTRL, field SUP_ATB_ON_REXT[3] (RW)
 *
 * Support Analog Test Bus On External Calibration Resistance This bit connects or disconnects the V
 * rext node to/from the analog test bus.
 *
 * Values:
 * - 0 - Disconnect the V rext node from the analog test bus.
 * - 1 - Connect the V rext node to the analog test bus.
 */
//@{
#define BP_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT      (3)      //!< Bit position for HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT.
#define BM_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT      (0x00000008)  //!< Bit mask for HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT.

//! @brief Get value of HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT from a register value.
#define BG_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT) >> BP_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT)

//! @brief Format value for bitfield HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT.
#define BF_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT) & BM_HDMI_PHY_MEASCTRL_SUP_ATB_ON_REXT)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_VLEVCTRL - Voltage Level Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_VLEVCTRL - Voltage Level Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : VLEVCTRL Access type : Read/write Address : 0x0E Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_vlevctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_vlevctrl_bitfields
    {
        unsigned short SUP_CK_LVL : 5; //!< [4:0] Support Clock Level
        unsigned short SUP_TX_LVL : 5; //!< [9:5] Support Transmitter Level
        unsigned short RESERVED0 : 6; //!< [15:10] Reserved
    } B;
} hw_hdmi_phy_vlevctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_VLEVCTRL register
 */
//@{
#define HW_HDMI_PHY_VLEVCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0xe)
//@}

/*
 * constants & macros for individual HDMI_PHY_VLEVCTRL bitfields
 */

/*! @name Register HDMI_PHY_VLEVCTRL, field SUP_CK_LVL[4:0] (RW)
 *
 * Support Clock Level This bus controls the reference voltage level of the Clock Channel module.
 * This voltage reference has a direct relation with the output signal voltage level. For more
 * information about the driver voltage level configuration, see .
 */
//@{
#define BP_HDMI_PHY_VLEVCTRL_SUP_CK_LVL      (0)      //!< Bit position for HDMI_PHY_VLEVCTRL_SUP_CK_LVL.
#define BM_HDMI_PHY_VLEVCTRL_SUP_CK_LVL      (0x0000001f)  //!< Bit mask for HDMI_PHY_VLEVCTRL_SUP_CK_LVL.

//! @brief Get value of HDMI_PHY_VLEVCTRL_SUP_CK_LVL from a register value.
#define BG_HDMI_PHY_VLEVCTRL_SUP_CK_LVL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_VLEVCTRL_SUP_CK_LVL) >> BP_HDMI_PHY_VLEVCTRL_SUP_CK_LVL)

//! @brief Format value for bitfield HDMI_PHY_VLEVCTRL_SUP_CK_LVL.
#define BF_HDMI_PHY_VLEVCTRL_SUP_CK_LVL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_VLEVCTRL_SUP_CK_LVL) & BM_HDMI_PHY_VLEVCTRL_SUP_CK_LVL)
//@}

/*! @name Register HDMI_PHY_VLEVCTRL, field SUP_TX_LVL[9:5] (RW)
 *
 * Support Transmitter Level This bus controls the reference voltage level of the three transmitter
 * channel modules. This voltage reference has a direct relation with the output signal voltage
 * level. For more information about the driver voltage level configuration, see .
 */
//@{
#define BP_HDMI_PHY_VLEVCTRL_SUP_TX_LVL      (5)      //!< Bit position for HDMI_PHY_VLEVCTRL_SUP_TX_LVL.
#define BM_HDMI_PHY_VLEVCTRL_SUP_TX_LVL      (0x000003e0)  //!< Bit mask for HDMI_PHY_VLEVCTRL_SUP_TX_LVL.

//! @brief Get value of HDMI_PHY_VLEVCTRL_SUP_TX_LVL from a register value.
#define BG_HDMI_PHY_VLEVCTRL_SUP_TX_LVL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_VLEVCTRL_SUP_TX_LVL) >> BP_HDMI_PHY_VLEVCTRL_SUP_TX_LVL)

//! @brief Format value for bitfield HDMI_PHY_VLEVCTRL_SUP_TX_LVL.
#define BF_HDMI_PHY_VLEVCTRL_SUP_TX_LVL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_VLEVCTRL_SUP_TX_LVL) & BM_HDMI_PHY_VLEVCTRL_SUP_TX_LVL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_D2ACTRL - Digital-to-Analog Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_D2ACTRL - Digital-to-Analog Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : D2ACTRL Access type : Read/write/override Address : 0x0F Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_d2actrl
{
    reg16_t U;
    struct _hw_hdmi_phy_d2actrl_bitfields
    {
        unsigned short SUP_DAC_TH_N : 3; //!< [2:0] Support Digital-to-Analog Thermometer Inverted
        unsigned short SUP_DAC_N : 8; //!< [10:3] Support Analog-to-Digital Inverted
        unsigned short RESERVED0 : 4; //!< [14:11] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_d2actrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_D2ACTRL register
 */
//@{
#define HW_HDMI_PHY_D2ACTRL_ADDR      (REGS_HDMI_PHY_BASE + 0xf)
//@}

/*
 * constants & macros for individual HDMI_PHY_D2ACTRL bitfields
 */

/*! @name Register HDMI_PHY_D2ACTRL, field SUP_DAC_TH_N[2:0] (RW)
 *
 * Support Digital-to-Analog Thermometer Inverted This bus value is inverted and defined in the
 * thermometer code to represent the binary code of the two MSB's of the 9-bit DAC value. Note : To
 * increase the stability of the DAC block, the two MSB's of the 9-bit DAC value are represented in
 * thermometer code, not in binary code. The MSB's of the 9-bit DAC value is split into two
 * thermometer-code bits. A transition from 0 to 1 of the 9-bit DAC value's MSB is represented by
 * "00" -> "01" -> "11" in thermometer code.
 */
//@{
#define BP_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N      (0)      //!< Bit position for HDMI_PHY_D2ACTRL_SUP_DAC_TH_N.
#define BM_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N      (0x00000007)  //!< Bit mask for HDMI_PHY_D2ACTRL_SUP_DAC_TH_N.

//! @brief Get value of HDMI_PHY_D2ACTRL_SUP_DAC_TH_N from a register value.
#define BG_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N) >> BP_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N)

//! @brief Format value for bitfield HDMI_PHY_D2ACTRL_SUP_DAC_TH_N.
#define BF_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N) & BM_HDMI_PHY_D2ACTRL_SUP_DAC_TH_N)
//@}

/*! @name Register HDMI_PHY_D2ACTRL, field SUP_DAC_N[10:3] (RW)
 *
 * Support Analog-to-Digital Inverted This bus represents the LSB's of the 9-bit DAC value.
 */
//@{
#define BP_HDMI_PHY_D2ACTRL_SUP_DAC_N      (3)      //!< Bit position for HDMI_PHY_D2ACTRL_SUP_DAC_N.
#define BM_HDMI_PHY_D2ACTRL_SUP_DAC_N      (0x000007f8)  //!< Bit mask for HDMI_PHY_D2ACTRL_SUP_DAC_N.

//! @brief Get value of HDMI_PHY_D2ACTRL_SUP_DAC_N from a register value.
#define BG_HDMI_PHY_D2ACTRL_SUP_DAC_N(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_D2ACTRL_SUP_DAC_N) >> BP_HDMI_PHY_D2ACTRL_SUP_DAC_N)

//! @brief Format value for bitfield HDMI_PHY_D2ACTRL_SUP_DAC_N.
#define BF_HDMI_PHY_D2ACTRL_SUP_DAC_N(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_D2ACTRL_SUP_DAC_N) & BM_HDMI_PHY_D2ACTRL_SUP_DAC_N)
//@}

/*! @name Register HDMI_PHY_D2ACTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_D2ACTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_D2ACTRL_OVERRIDE.
#define BM_HDMI_PHY_D2ACTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_D2ACTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_D2ACTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_D2ACTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_D2ACTRL_OVERRIDE) >> BP_HDMI_PHY_D2ACTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_D2ACTRL_OVERRIDE.
#define BF_HDMI_PHY_D2ACTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_D2ACTRL_OVERRIDE) & BM_HDMI_PHY_D2ACTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_CURRCTRL - Current Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_CURRCTRL - Current Control (RW)
 *
 * Reset value: 0x08ab
 *
 * Register name : CURRCTRL Access type : Read/write Address : 0x10 Value at reset : 0x08AB
 */
typedef union _hw_hdmi_phy_currctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_currctrl_bitfields
    {
        unsigned short PLL_INT_CNTRL : 3; //!< [2:0] PLL Charge Pump Integral Control
        unsigned short PLL_PROP_CNTRL : 3; //!< [5:3] PLL Proportional Control
        unsigned short MPLL_INT_CNTRL : 3; //!< [8:6] MPLL Integral Control
        unsigned short MPLL_PROP_CNTRL : 3; //!< [11:9] MPLL Proportional Control
        unsigned short RESERVED0 : 4; //!< [15:12] Reserved
    } B;
} hw_hdmi_phy_currctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_CURRCTRL register
 */
//@{
#define HW_HDMI_PHY_CURRCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x10)
//@}

/*
 * constants & macros for individual HDMI_PHY_CURRCTRL bitfields
 */

/*! @name Register HDMI_PHY_CURRCTRL, field PLL_INT_CNTRL[2:0] (RW)
 *
 * PLL Charge Pump Integral Control This bus controls the PLL charge pump integral current. Eight
 * levels of charge pump integral current value are possible. The specific values are defined in .
 * Default (reset) value of pll_int_cntrl[2:0] is 100.
 */
//@{
#define BP_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL      (0)      //!< Bit position for HDMI_PHY_CURRCTRL_PLL_INT_CNTRL.
#define BM_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL      (0x00000007)  //!< Bit mask for HDMI_PHY_CURRCTRL_PLL_INT_CNTRL.

//! @brief Get value of HDMI_PHY_CURRCTRL_PLL_INT_CNTRL from a register value.
#define BG_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL) >> BP_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_CURRCTRL_PLL_INT_CNTRL.
#define BF_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL) & BM_HDMI_PHY_CURRCTRL_PLL_INT_CNTRL)
//@}

/*! @name Register HDMI_PHY_CURRCTRL, field PLL_PROP_CNTRL[5:3] (RW)
 *
 * PLL Proportional Control This bus controls the PLL charge pump proportional current. Eight levels
 * of charge pump proportional current value are possible. The specific values are defined in .
 * Default (reset) value of pll_int_cntrl is 011.
 */
//@{
#define BP_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL      (3)      //!< Bit position for HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL.
#define BM_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL      (0x00000038)  //!< Bit mask for HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL.

//! @brief Get value of HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL from a register value.
#define BG_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL) >> BP_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL.
#define BF_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL) & BM_HDMI_PHY_CURRCTRL_PLL_PROP_CNTRL)
//@}

/*! @name Register HDMI_PHY_CURRCTRL, field MPLL_INT_CNTRL[8:6] (RW)
 *
 * MPLL Integral Control This bus controls the charge pump integral current. Eight levels of charge
 * pump integral current value are possible. The specific values are defined in . Default (reset)
 * value of pll_int_cntrl[1:0] is 100.
 */
//@{
#define BP_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL      (6)      //!< Bit position for HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL.
#define BM_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL      (0x000001c0)  //!< Bit mask for HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL.

//! @brief Get value of HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL from a register value.
#define BG_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL) >> BP_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL.
#define BF_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL) & BM_HDMI_PHY_CURRCTRL_MPLL_INT_CNTRL)
//@}

/*! @name Register HDMI_PHY_CURRCTRL, field MPLL_PROP_CNTRL[11:9] (RW)
 *
 * MPLL Proportional Control This bus controls the MPLL charge pump proportional current. Eight
 * levels of charge pump proportional current value are possible. The specific values are defined in
 * . Default (reset) value of pll_prop_cntrl[1:0] is 100.
 */
//@{
#define BP_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL      (9)      //!< Bit position for HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL.
#define BM_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL      (0x00000e00)  //!< Bit mask for HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL.

//! @brief Get value of HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL from a register value.
#define BG_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL) >> BP_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL.
#define BF_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL) & BM_HDMI_PHY_CURRCTRL_MPLL_PROP_CNTRL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_DRVANACTRL - Drive Analog Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_DRVANACTRL - Drive Analog Control (RW)
 *
 * Reset value: 0x0003
 *
 * Register name : DRVANACTRL Access type : Read/write/override Address : 0x11 Value at reset :
 * 0x0003
 */
typedef union _hw_hdmi_phy_drvanactrl
{
    reg16_t U;
    struct _hw_hdmi_phy_drvanactrl_bitfields
    {
        unsigned short MPLL_DRV_ANA : 1; //!< [0] MPLL Drive Analog
        unsigned short PLL_DRV_ANA : 1; //!< [1] PLL Drive Analog
        unsigned short RESERVED0 : 13; //!< [14:2] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_drvanactrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_DRVANACTRL register
 */
//@{
#define HW_HDMI_PHY_DRVANACTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x11)
//@}

/*
 * constants & macros for individual HDMI_PHY_DRVANACTRL bitfields
 */

/*! @name Register HDMI_PHY_DRVANACTRL, field MPLL_DRV_ANA[0] (RW)
 *
 * MPLL Drive Analog This bit enables or disables driving the ck_ref_p/m clocks to all transmitters
 * (tx_topa). Default (reset) value of mpll_drv_ana is 1.
 *
 * Values:
 * - 0 - Set ck_ref_p high; ck_ref_m low, if the Override bit is 0.
 * - 1 - Enable ck_ref_mpll output clock (125-1700 MHz ck_ref_p/m) to be driven to all transmitters
 *     (tx_topa), if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA      (0)      //!< Bit position for HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA.
#define BM_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA      (0x00000001)  //!< Bit mask for HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA.

//! @brief Get value of HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA from a register value.
#define BG_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA) >> BP_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA)

//! @brief Format value for bitfield HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA.
#define BF_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA) & BM_HDMI_PHY_DRVANACTRL_MPLL_DRV_ANA)
//@}

/*! @name Register HDMI_PHY_DRVANACTRL, field PLL_DRV_ANA[1] (RW)
 *
 * PLL Drive Analog This bit enables or disables driving the ck_ref_mpll_p/m clocks to the MPLL
 * module. Default (reset) value of pll_drv_ana is 1.
 *
 * Values:
 * - 0 - Set ck_ref_mpll low, if the Override bit is 0.
 * - 1 - Enable 25-340 MHz output clock (ck_ref_mpll_p/m) to be driven to MPLL, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA      (1)      //!< Bit position for HDMI_PHY_DRVANACTRL_PLL_DRV_ANA.
#define BM_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA      (0x00000002)  //!< Bit mask for HDMI_PHY_DRVANACTRL_PLL_DRV_ANA.

//! @brief Get value of HDMI_PHY_DRVANACTRL_PLL_DRV_ANA from a register value.
#define BG_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA) >> BP_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA)

//! @brief Format value for bitfield HDMI_PHY_DRVANACTRL_PLL_DRV_ANA.
#define BF_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA) & BM_HDMI_PHY_DRVANACTRL_PLL_DRV_ANA)
//@}

/*! @name Register HDMI_PHY_DRVANACTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_DRVANACTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_DRVANACTRL_OVERRIDE.
#define BM_HDMI_PHY_DRVANACTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_DRVANACTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_DRVANACTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_DRVANACTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DRVANACTRL_OVERRIDE) >> BP_HDMI_PHY_DRVANACTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_DRVANACTRL_OVERRIDE.
#define BF_HDMI_PHY_DRVANACTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DRVANACTRL_OVERRIDE) & BM_HDMI_PHY_DRVANACTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_PLLMEASCTRL - PLL Measure Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_PLLMEASCTRL - PLL Measure Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : PLLMEASCTRL Access type : Read/write Address : 0x12 Value at reset : 0x0000 With
 * the exception of pll_atb_sense_sel and pll_meas_iv[9], two or more of the previous register bits
 * must not be set to 1 simultaneously; doing so can lead to a hardware problem. The table below
 * describes the pll_meas_iv[10:0] bit settings. pll_meas_iv[10:0] Effective Bit Pll_meas_iv[10:0]
 * Value Description Pll_meas_iv[0] 00000000001 Not used. Pll_meas_iv[1] 00000000010 Not used in
 * pll_top. Connected to fast_tech pins of PLL and MPLL in hdmi_topa. Pll_meas_iv[2] 00000000100
 * Connects VP supply voltage to the atb_sense line. Pll_meas_iv[3] 00000001000 Connects vp_cp to
 * the atb_sense line. Pll_meas_iv[4] 00000010000 Connects internal supply voltage of the VCO (ivco)
 * to the atb_sense line. Pll_meas_iv[5] 00000100000 Connects vp_cko voltage to the atb_sense line.
 * Pll_meas_iv[6] 00001000000 Connects node vpsf to the atb_sense line. Pll_meas_iv[7] 00010000000
 * Connects vref to atb_sense line. Pll_meas_iv[8] 00100000000 Connects vcntrl to atb_sense line.
 * Pll_meas_iv[9] 01000000000 Enables the phase mixer and pll_cko_pm_p/m. Pll_meas_iv[10]
 * 10000000000 Measures the voltage corresponding to the output phase of the clr_dpth divider
 * (fb_clk) with respect to refclk.
 */
typedef union _hw_hdmi_phy_pllmeasctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_pllmeasctrl_bitfields
    {
        unsigned short PLL_MEAS_GD : 1; //!< [0] PLL Measure Ground
        unsigned short PLL_MEAS_IV : 11; //!< [11:1] PLL Measure Internal Voltage
        unsigned short PLL_ATB_SENSE_SEL : 1; //!< [12] PLL Analog Test Bus Sense Select
        unsigned short RESERVED0 : 3; //!< [15:13] Reserved
    } B;
} hw_hdmi_phy_pllmeasctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_PLLMEASCTRL register
 */
//@{
#define HW_HDMI_PHY_PLLMEASCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x12)
//@}

/*
 * constants & macros for individual HDMI_PHY_PLLMEASCTRL bitfields
 */

/*! @name Register HDMI_PHY_PLLMEASCTRL, field PLL_MEAS_GD[0] (RW)
 *
 * PLL Measure Ground This bit connects or disconnects the ground signal to the atb_sense (analog
 * test bus) bus.
 *
 * Values:
 * - 0 - Disconnect the ground signal from the atb_sense bus.
 * - 1 - Connect the ground signal to the atb_sense bus.
 */
//@{
#define BP_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD      (0)      //!< Bit position for HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD.
#define BM_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD      (0x00000001)  //!< Bit mask for HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD.

//! @brief Get value of HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD from a register value.
#define BG_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD) >> BP_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD)

//! @brief Format value for bitfield HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD.
#define BF_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD) & BM_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_GD)
//@}

/*! @name Register HDMI_PHY_PLLMEASCTRL, field PLL_MEAS_IV[11:1] (RW)
 *
 * PLL Measure Internal Voltage This bus enables or disables measuring various PLL node voltages and
 * branch currents. For information about the bit settings, see the pll_meas_iv[10:0] table.
 */
//@{
#define BP_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV      (1)      //!< Bit position for HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV.
#define BM_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV      (0x00000ffe)  //!< Bit mask for HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV.

//! @brief Get value of HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV from a register value.
#define BG_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV) >> BP_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV)

//! @brief Format value for bitfield HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV.
#define BF_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV) & BM_HDMI_PHY_PLLMEASCTRL_PLL_MEAS_IV)
//@}

/*! @name Register HDMI_PHY_PLLMEASCTRL, field PLL_ATB_SENSE_SEL[12] (RW)
 *
 * PLL Analog Test Bus Sense Select This bit enables or disables internal signals of the PLL to be
 * connected to the analog test bus. Without setting this bit, no measurements can be made on the
 * atb_sense line. Default (reset) value of pll_atb_sense_sel is 0.
 *
 * Values:
 * - 0 - Disable the ability to measure internal DC signals on the atb_sense line in the PLL.
 * - 1 - Enable the ability to measure internal DC signals on the atb_sense line in the PLL.
 */
//@{
#define BP_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL      (12)      //!< Bit position for HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL.
#define BM_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL      (0x00001000)  //!< Bit mask for HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL.

//! @brief Get value of HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL from a register value.
#define BG_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL) >> BP_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL)

//! @brief Format value for bitfield HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL.
#define BF_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL) & BM_HDMI_PHY_PLLMEASCTRL_PLL_ATB_SENSE_SEL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_PLLPHBYCTRL - PLL Phase and Bypass Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_PLLPHBYCTRL - PLL Phase and Bypass Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : PLLPHBYCTRL Access type : Read/write Address : 0x13 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_pllphbyctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_pllphbyctrl_bitfields
    {
        unsigned short PLL_PH_SEL : 10; //!< [9:0] PLL Phase Select
        unsigned short PLL_PH_SEL_CK : 1; //!< [10] PLL Phase Select Clock
        unsigned short BYPASS_PPLL : 1; //!< [11] Bypass Pre-PLL
        unsigned short RESERVED0 : 4; //!< [15:12] Reserved
    } B;
} hw_hdmi_phy_pllphbyctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_PLLPHBYCTRL register
 */
//@{
#define HW_HDMI_PHY_PLLPHBYCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x13)
//@}

/*
 * constants & macros for individual HDMI_PHY_PLLPHBYCTRL bitfields
 */

/*! @name Register HDMI_PHY_PLLPHBYCTRL, field PLL_PH_SEL[9:0] (RW)
 *
 * PLL Phase Select This bus is a control word for the PLL's phase mixer that enables the phase of
 * pll_cko_pm_p/m to be varied ± 0.5 UI of the VCO frequency, which is 740-1,480 MHz.
 */
//@{
#define BP_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL      (0)      //!< Bit position for HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL.
#define BM_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL      (0x000003ff)  //!< Bit mask for HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL.

//! @brief Get value of HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL from a register value.
#define BG_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL) >> BP_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL)

//! @brief Format value for bitfield HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL.
#define BF_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL) & BM_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL)
//@}

/*! @name Register HDMI_PHY_PLLPHBYCTRL, field PLL_PH_SEL_CK[10] (RW)
 *
 * PLL Phase Select Clock This bit enables or disables latching the ph_sel[9:0] into a 9-bit DAC
 * used in the phase mixer.
 *
 * Values:
 * - 0 - Disable latching the pll_ph_sel[9:0] into the 9-bit DAC.
 * - 1 - Enable latching the pll_ph_sel[9:0] into the 9-bit DAC.
 */
//@{
#define BP_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK      (10)      //!< Bit position for HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK.
#define BM_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK      (0x00000400)  //!< Bit mask for HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK.

//! @brief Get value of HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK from a register value.
#define BG_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK) >> BP_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK)

//! @brief Format value for bitfield HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK.
#define BF_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK) & BM_HDMI_PHY_PLLPHBYCTRL_PLL_PH_SEL_CK)
//@}

/*! @name Register HDMI_PHY_PLLPHBYCTRL, field BYPASS_PPLL[11] (RW)
 *
 * Bypass Pre-PLL This bit enables or disables bypassing the pre-PLL.
 *
 * Values:
 * - 0 - Disable bypassing pll_top by forcing refclk_mpll_ref low.
 * - 1 - Enable bypassing pll_top by buffering refclk to refclk_mpll_ref.
 */
//@{
#define BP_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL      (11)      //!< Bit position for HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL.
#define BM_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL      (0x00000800)  //!< Bit mask for HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL.

//! @brief Get value of HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL from a register value.
#define BG_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL) >> BP_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL)

//! @brief Format value for bitfield HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL.
#define BF_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL) & BM_HDMI_PHY_PLLPHBYCTRL_BYPASS_PPLL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_GRP_CTRL - Gear Shift, Reset Mode, and Power State Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_GRP_CTRL - Gear Shift, Reset Mode, and Power State Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : - Access type : Read/write/override Address : 0x14 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_grp_ctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_grp_ctrl_bitfields
    {
        unsigned short MPLL_GEAR_SHIFT : 1; //!< [0] MPLL Gear Shift
        unsigned short PLL_GEAR_SHIFT : 1; //!< [1] PLL Gear Shift
        unsigned short MPLL_RST : 1; //!< [2] MPLL Reset
        unsigned short MPLL_PWR_ON : 1; //!< [3] MPLL Power-On
        unsigned short PLL_RST : 1; //!< [4] PLL Reset
        unsigned short PLL_PWR_ON : 1; //!< [5] PLL Power-On
        unsigned short RESERVED0 : 9; //!< [14:6] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_grp_ctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_GRP_CTRL register
 */
//@{
#define HW_HDMI_PHY_GRP_CTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x14)
//@}

/*
 * constants & macros for individual HDMI_PHY_GRP_CTRL bitfields
 */

/*! @name Register HDMI_PHY_GRP_CTRL, field MPLL_GEAR_SHIFT[0] (RW)
 *
 * MPLL Gear Shift This bit enables or disables Rapid Locking mode, where the mpll_gear_shift bit is
 * asserted for 25 µs when coming out of reset, then deasserted before clocks are valid.
 *
 * Values:
 * - 0 - Disable Rapid Locking mode, if the Override bit is 0.
 * - 1 - Enable Rapid Locking mode, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT      (0)      //!< Bit position for HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT.
#define BM_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT      (0x00000001)  //!< Bit mask for HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT.

//! @brief Get value of HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT from a register value.
#define BG_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT) >> BP_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT.
#define BF_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT) & BM_HDMI_PHY_GRP_CTRL_MPLL_GEAR_SHIFT)
//@}

/*! @name Register HDMI_PHY_GRP_CTRL, field PLL_GEAR_SHIFT[1] (RW)
 *
 * PLL Gear Shift This bit enables or disables Rapid Locking mode, where the pll_gear_shift bit is
 * asserted for 25 µs when coming out of reset, then deasserted before clocks are valid.
 *
 * Values:
 * - 0 - Disable Rapid Locking mode, if the Override bit is 0.
 * - 1 - Enable Rapid Locking mode, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT      (1)      //!< Bit position for HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT.
#define BM_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT      (0x00000002)  //!< Bit mask for HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT.

//! @brief Get value of HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT from a register value.
#define BG_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT) >> BP_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT.
#define BF_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT) & BM_HDMI_PHY_GRP_CTRL_PLL_GEAR_SHIFT)
//@}

/*! @name Register HDMI_PHY_GRP_CTRL, field MPLL_RST[2] (RW)
 *
 * MPLL Reset This bit is used to place the MPLL in Reset mode.
 *
 * Values:
 * - 0 - Enable MPLL to operate normally, if the Override bit is 0.
 * - 1 - Place the MPLL in Reset mode, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_MPLL_RST      (2)      //!< Bit position for HDMI_PHY_GRP_CTRL_MPLL_RST.
#define BM_HDMI_PHY_GRP_CTRL_MPLL_RST      (0x00000004)  //!< Bit mask for HDMI_PHY_GRP_CTRL_MPLL_RST.

//! @brief Get value of HDMI_PHY_GRP_CTRL_MPLL_RST from a register value.
#define BG_HDMI_PHY_GRP_CTRL_MPLL_RST(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_MPLL_RST) >> BP_HDMI_PHY_GRP_CTRL_MPLL_RST)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_MPLL_RST.
#define BF_HDMI_PHY_GRP_CTRL_MPLL_RST(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_MPLL_RST) & BM_HDMI_PHY_GRP_CTRL_MPLL_RST)
//@}

/*! @name Register HDMI_PHY_GRP_CTRL, field MPLL_PWR_ON[3] (RW)
 *
 * MPLL Power-On This bit is used to power-on/off the MPLL module.
 *
 * Values:
 * - 0 - Power on MPLL and set all output clocks to DC levels, if the Override bit is 0.
 * - 1 - Power off MPLL and enable it to operate normally, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON      (3)      //!< Bit position for HDMI_PHY_GRP_CTRL_MPLL_PWR_ON.
#define BM_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON      (0x00000008)  //!< Bit mask for HDMI_PHY_GRP_CTRL_MPLL_PWR_ON.

//! @brief Get value of HDMI_PHY_GRP_CTRL_MPLL_PWR_ON from a register value.
#define BG_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON) >> BP_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_MPLL_PWR_ON.
#define BF_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON) & BM_HDMI_PHY_GRP_CTRL_MPLL_PWR_ON)
//@}

/*! @name Register HDMI_PHY_GRP_CTRL, field PLL_RST[4] (RW)
 *
 * PLL Reset This bit is used to place the MPLL in Reset mode.
 *
 * Values:
 * - 0 - Enable PLL to operate normally, if the Override bit is 0.
 * - 1 - Place the PLL in Reset mode, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_PLL_RST      (4)      //!< Bit position for HDMI_PHY_GRP_CTRL_PLL_RST.
#define BM_HDMI_PHY_GRP_CTRL_PLL_RST      (0x00000010)  //!< Bit mask for HDMI_PHY_GRP_CTRL_PLL_RST.

//! @brief Get value of HDMI_PHY_GRP_CTRL_PLL_RST from a register value.
#define BG_HDMI_PHY_GRP_CTRL_PLL_RST(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_PLL_RST) >> BP_HDMI_PHY_GRP_CTRL_PLL_RST)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_PLL_RST.
#define BF_HDMI_PHY_GRP_CTRL_PLL_RST(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_PLL_RST) & BM_HDMI_PHY_GRP_CTRL_PLL_RST)
//@}

/*! @name Register HDMI_PHY_GRP_CTRL, field PLL_PWR_ON[5] (RW)
 *
 * PLL Power-On This bit is used to power on/off the PLL module. Note: If the Override bit is set to
 * 1, the working value is the Override bit value, not the registered value.
 *
 * Values:
 * - 0 - Power off PLL and draw minimal current, if the Override bit is 0.
 * - 1 - Power on PLL and enable it to operate normally, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_PLL_PWR_ON      (5)      //!< Bit position for HDMI_PHY_GRP_CTRL_PLL_PWR_ON.
#define BM_HDMI_PHY_GRP_CTRL_PLL_PWR_ON      (0x00000020)  //!< Bit mask for HDMI_PHY_GRP_CTRL_PLL_PWR_ON.

//! @brief Get value of HDMI_PHY_GRP_CTRL_PLL_PWR_ON from a register value.
#define BG_HDMI_PHY_GRP_CTRL_PLL_PWR_ON(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_PLL_PWR_ON) >> BP_HDMI_PHY_GRP_CTRL_PLL_PWR_ON)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_PLL_PWR_ON.
#define BF_HDMI_PHY_GRP_CTRL_PLL_PWR_ON(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_PLL_PWR_ON) & BM_HDMI_PHY_GRP_CTRL_PLL_PWR_ON)
//@}

/*! @name Register HDMI_PHY_GRP_CTRL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_GRP_CTRL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_GRP_CTRL_OVERRIDE.
#define BM_HDMI_PHY_GRP_CTRL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_GRP_CTRL_OVERRIDE.

//! @brief Get value of HDMI_PHY_GRP_CTRL_OVERRIDE from a register value.
#define BG_HDMI_PHY_GRP_CTRL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GRP_CTRL_OVERRIDE) >> BP_HDMI_PHY_GRP_CTRL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_GRP_CTRL_OVERRIDE.
#define BF_HDMI_PHY_GRP_CTRL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GRP_CTRL_OVERRIDE) & BM_HDMI_PHY_GRP_CTRL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_GMPCTRL - Gmp Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_GMPCTRL - Gmp Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : GMPCTRL Access type : Read/write Address : 0x15 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_gmpctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_gmpctrl_bitfields
    {
        unsigned short MPLL_GMP_CNTRL : 2; //!< [1:0] MPLL gmp Control
        unsigned short PLL_GMP_CNTRL : 2; //!< [3:2] PLL gmp Control
        unsigned short RESERVED0 : 12; //!< [15:4] Reserved
    } B;
} hw_hdmi_phy_gmpctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_GMPCTRL register
 */
//@{
#define HW_HDMI_PHY_GMPCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x15)
//@}

/*
 * constants & macros for individual HDMI_PHY_GMPCTRL bitfields
 */

/*! @name Register HDMI_PHY_GMPCTRL, field MPLL_GMP_CNTRL[1:0] (RW)
 *
 * MPLL gmp Control This bus controls the effective loop-filter resistance (= 1/gmp) to increase or
 * decrease MPLL bandwidth and to compensate for changes in the Divider module (n_cntrl).
 *
 * Values:
 * - 00 - TMDS rate up to 45.25 MHz
 * - 01 - TMDS rate of 45.26-92.5 MHz
 * - 10 - TMDS rate of 92.51-185 MHz
 * - 11 - TMDS rate of 184.1-370 MHz
 */
//@{
#define BP_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL      (0)      //!< Bit position for HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL.
#define BM_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL      (0x00000003)  //!< Bit mask for HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL.

//! @brief Get value of HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL from a register value.
#define BG_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL) >> BP_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL.
#define BF_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL) & BM_HDMI_PHY_GMPCTRL_MPLL_GMP_CNTRL)
//@}

/*! @name Register HDMI_PHY_GMPCTRL, field PLL_GMP_CNTRL[3:2] (RW)
 *
 * PLL gmp Control This bus controls the effective loop-filter resistance (equal) to increase or
 * decrease PLL bandwidth and to compensate for changes in the Divider module (n_cntrl).
 *
 * Values:
 * - 00 - TMDS rate up to 45.25 MHz
 * - 01 - TMDS rate of 45.26-92.5 MHz
 * - 10 - TMDS rate of 92.51-185 MHz
 * - 11 - TMDS rate of 184.1-370 MHz
 */
//@{
#define BP_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL      (2)      //!< Bit position for HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL.
#define BM_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL      (0x0000000c)  //!< Bit mask for HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL.

//! @brief Get value of HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL from a register value.
#define BG_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL) >> BP_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL)

//! @brief Format value for bitfield HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL.
#define BF_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL) & BM_HDMI_PHY_GMPCTRL_PLL_GMP_CNTRL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_MPLLMEASCTRL - MPLL Measure Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_MPLLMEASCTRL - MPLL Measure Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : MPLLMEASCTRL Access type : Read/write Address : 0x16 Value at reset : 0x0000 With
 * the exception of mpll_atb_sense_sel, mpll_meas_iv[9], and mpll_meas_iv[11], two or more of the
 * previous register bits must not be set to 1 simultaneously, because doing so can lead to a
 * hardware problem. The table below describes the mpll_meas_iv[11:0] bit settings.
 * mpll_meas_iv[11:0] Effective Bit mpll_meas_iv[11:0] Value Description mpll_meas_iv[0]
 * 000000000001 Connects the internal positive DCC control line (vc0p) to the atb_sense line.
 * mpll_meas_iv[1] 000000000010 Connects the internal negative DCC control line (vc0m) to the
 * atb_sense line. mpll_meas_iv[2] 000000000100 Connects VP supply voltage to the atb_sense line.
 * mpll_meas_iv[3] 000000001000 Connects vp_cp to the atb_sense line. mpll_meas_iv[4] 000000010000
 * Connects the internal supply voltage of the VCO (ivco) to the atb_sense line through a low-pass
 * filter. mpll_meas_iv[5] 000000100000 Connects the vp_cko voltage to the atb_sense line.
 * mpll_meas_iv[6] 000001000000 Connects the vpsf node to the atb_sense line. mpll_meas_iv[7]
 * 000010000000 Connects vref to the atb_sense line. mpll_meas_iv[8] 000100000000 Connects vcntrl to
 * the atb_sense line. mpll_meas_iv[9] 001000000000 Enables the phase mixer and cko_pm_p/m.
 * mpll_meas_iv[10] 010000000000 Measures the voltage corresponding to the phase of the divide-by-5
 * output (fb_clk) with respect to the phase of the mpll_ana input (ck_refclk_p). mpll_meas_iv[11]
 * 100000000000 Forces div_x1 low; therefore, bitclk_p/m is multiplexed to ck_ref_p/m (normally, if
 * n_cntrl = 00, ck0_p/m is multiplexed to ck_ref_p/m and DCC loop is enabled.
 */
typedef union _hw_hdmi_phy_mpllmeasctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_mpllmeasctrl_bitfields
    {
        unsigned short MPLL_MEAS_GD : 1; //!< [0] MPLL Measure Ground
        unsigned short MPLL_MEAS_IV : 12; //!< [12:1] MPLL Measure Internal Voltage
        unsigned short MPLL_ATB_SENSE_SEL : 1; //!< [13] MPLL Analog Test Bus Sense Select
        unsigned short RESERVED0 : 2; //!< [15:14] Reserved
    } B;
} hw_hdmi_phy_mpllmeasctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_MPLLMEASCTRL register
 */
//@{
#define HW_HDMI_PHY_MPLLMEASCTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x16)
//@}

/*
 * constants & macros for individual HDMI_PHY_MPLLMEASCTRL bitfields
 */

/*! @name Register HDMI_PHY_MPLLMEASCTRL, field MPLL_MEAS_GD[0] (RW)
 *
 * MPLL Measure Ground This bit connects or disconnects the ground signal to the atb_sense (analog
 * test bus) bus.
 *
 * Values:
 * - 0 - Disconnect the ground signal from the atb_sense bus.
 * - 1 - Connect the ground signal to the atb_sense bus.
 */
//@{
#define BP_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD      (0)      //!< Bit position for HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD.
#define BM_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD      (0x00000001)  //!< Bit mask for HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD.

//! @brief Get value of HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD from a register value.
#define BG_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD) >> BP_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD)

//! @brief Format value for bitfield HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD.
#define BF_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD) & BM_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_GD)
//@}

/*! @name Register HDMI_PHY_MPLLMEASCTRL, field MPLL_MEAS_IV[12:1] (RW)
 *
 * MPLL Measure Internal Voltage This bus enables or disables measuring various PLL node voltages
 * and branch currents. For information about the bit settings, see the mpll_meas_iv[11:0] table.
 */
//@{
#define BP_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV      (1)      //!< Bit position for HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV.
#define BM_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV      (0x00001ffe)  //!< Bit mask for HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV.

//! @brief Get value of HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV from a register value.
#define BG_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV) >> BP_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV)

//! @brief Format value for bitfield HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV.
#define BF_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV) & BM_HDMI_PHY_MPLLMEASCTRL_MPLL_MEAS_IV)
//@}

/*! @name Register HDMI_PHY_MPLLMEASCTRL, field MPLL_ATB_SENSE_SEL[13] (RW)
 *
 * MPLL Analog Test Bus Sense Select This bit enables or disables internal signals of the PLL to be
 * connected to the analog test bus. Without setting this bit, no measurements can be made on the
 * atb_sense line. Default (reset) value of mpll_atb_sense_sel is 0.
 *
 * Values:
 * - 0 - Disable the ability to measure internal DC signals on the atb_sense line in the PLL.
 * - 1 - Enable the ability to measure internal DC signals on the atb_sense line in the PLL.
 */
//@{
#define BP_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL      (13)      //!< Bit position for HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL.
#define BM_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL      (0x00002000)  //!< Bit mask for HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL.

//! @brief Get value of HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL from a register value.
#define BG_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL) >> BP_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL)

//! @brief Format value for bitfield HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL.
#define BF_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL) & BM_HDMI_PHY_MPLLMEASCTRL_MPLL_ATB_SENSE_SEL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_MSM_CTRL - MPLL and PLL Phase, Scope Clock Select, and MUX Clock Control
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_MSM_CTRL - MPLL and PLL Phase, Scope Clock Select, and MUX Clock Control (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : - Access type : Read/write Address : 0x17 Value at reset : 0x0000 The table below
 * describes the cko_sel[1:0] bit settings. (The cko_sel[1:0] default value is 00.) cko_sel[1:0]
 * cko_sel[1:0] TMDS Clock Mode PLL and MPLL Mode Output TMDS Clock on TMDS Channel 00 Non-Coherent
 * Normal ck_ref_mpll_p/m (Pre-PLL out) 01 Off (PLL and MPLL are both off) Normal Off (No output
 * TMDS clock) 10 Test (PHY in test mode) Normal PCLK (Input reference clock to HDMI 3D Tx PHY) 11
 * Coherent Normal fb_clk (MPLL feedback clock) 00 Off (PLL and MPLL are both off) Bypass Off (No
 * output TMDS clock) 01 Off (PLL and MPLL are both off) Bypass Off (No output TMDS clock) 10 Non-
 * Coherent Bypass PCLK (Input reference clock to HDMI 3D Tx PHY) 11 Coherent Bypass fb_clk (MPLL
 * feedback clock)
 */
typedef union _hw_hdmi_phy_msm_ctrl
{
    reg16_t U;
    struct _hw_hdmi_phy_msm_ctrl_bitfields
    {
        unsigned short SCOPE_CK_SEL : 1; //!< [0] Scope Clock Select
        unsigned short CKO_SEL : 2; //!< [2:1] Clock Output Select
        unsigned short MPLL_PH_SEL : 10; //!< [12:3] MPLL Phase Select
        unsigned short MPLL_PH_SEL_CK : 1; //!< [13] MPLL Phase Select Clock
        unsigned short RESERVED0 : 2; //!< [15:14] Reserved
    } B;
} hw_hdmi_phy_msm_ctrl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_MSM_CTRL register
 */
//@{
#define HW_HDMI_PHY_MSM_CTRL_ADDR      (REGS_HDMI_PHY_BASE + 0x17)
//@}

/*
 * constants & macros for individual HDMI_PHY_MSM_CTRL bitfields
 */

/*! @name Register HDMI_PHY_MSM_CTRL, field SCOPE_CK_SEL[0] (RW)
 *
 * Scope Clock Select Selects the clock to connect to the scope clock signal: the differential
 * pll_cko_p/m or the differential mpll_cko_p/m.
 *
 * Values:
 * - 0 - Connect the mpll_cko_pm_p/m to the clock scope (this clock has a range of 23.125-45.25 MHz) where
 *     the mpll_meas_iv[9] bit must be high.
 * - 1 - Connect the pll_cko_pm_p/m to the clock scope (this clock has a range of 23.125-45.25 MHz) where the
 *     pll_meas_iv[9] bit must be high.
 */
//@{
#define BP_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL      (0)      //!< Bit position for HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL.
#define BM_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL      (0x00000001)  //!< Bit mask for HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL.

//! @brief Get value of HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL from a register value.
#define BG_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL) >> BP_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL)

//! @brief Format value for bitfield HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL.
#define BF_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL) & BM_HDMI_PHY_MSM_CTRL_SCOPE_CK_SEL)
//@}

/*! @name Register HDMI_PHY_MSM_CTRL, field CKO_SEL[2:1] (RW)
 *
 * Clock Output Select This bus selects the clock to be connected to the output TMDS clock channel.
 * Notes: Normal mode: The color depth or pixel repetition is required, which means that the PLL is
 * powered on (pll_pwr_on bit is set to 1) and the bypass_ppll bit is set to 0. Bypass mode: The
 * color depth and the pixel repetition is not required, which means that the PLL is powered off
 * (pll_pwr_on bit is set to 0) and the bypass_ppll bit is set to 1. For information about the
 * cko_sel[1:0] bit settings and corresponding PLL/MPLL modes, see the cko_sel[1:0] table.
 */
//@{
#define BP_HDMI_PHY_MSM_CTRL_CKO_SEL      (1)      //!< Bit position for HDMI_PHY_MSM_CTRL_CKO_SEL.
#define BM_HDMI_PHY_MSM_CTRL_CKO_SEL      (0x00000006)  //!< Bit mask for HDMI_PHY_MSM_CTRL_CKO_SEL.

//! @brief Get value of HDMI_PHY_MSM_CTRL_CKO_SEL from a register value.
#define BG_HDMI_PHY_MSM_CTRL_CKO_SEL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MSM_CTRL_CKO_SEL) >> BP_HDMI_PHY_MSM_CTRL_CKO_SEL)

//! @brief Format value for bitfield HDMI_PHY_MSM_CTRL_CKO_SEL.
#define BF_HDMI_PHY_MSM_CTRL_CKO_SEL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MSM_CTRL_CKO_SEL) & BM_HDMI_PHY_MSM_CTRL_CKO_SEL)
//@}

/*! @name Register HDMI_PHY_MSM_CTRL, field MPLL_PH_SEL[12:3] (RW)
 *
 * MPLL Phase Select This bus is a control word for the MPLL's phase mixer and enables the phase of
 * pll_cko_pm_p /m to be varied ± 0.5 UI of the VCO frequency, which has a range of 925-1,850 MHz.
 */
//@{
#define BP_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL      (3)      //!< Bit position for HDMI_PHY_MSM_CTRL_MPLL_PH_SEL.
#define BM_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL      (0x00001ff8)  //!< Bit mask for HDMI_PHY_MSM_CTRL_MPLL_PH_SEL.

//! @brief Get value of HDMI_PHY_MSM_CTRL_MPLL_PH_SEL from a register value.
#define BG_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL) >> BP_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL)

//! @brief Format value for bitfield HDMI_PHY_MSM_CTRL_MPLL_PH_SEL.
#define BF_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL) & BM_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL)
//@}

/*! @name Register HDMI_PHY_MSM_CTRL, field MPLL_PH_SEL_CK[13] (RW)
 *
 * MPLL Phase Select Clock This bit enables or disables latching ph_sel[9:0] into a 9-bit DAC used
 * in the phase mixer.
 *
 * Values:
 * - 0 - Disable latching mpll_ph_sel[9:0] into the 9-bit DAC.
 * - 1 - Enable latching mpll_ph_sel[9:0] into the 9-bit DAC.
 */
//@{
#define BP_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK      (13)      //!< Bit position for HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK.
#define BM_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK      (0x00002000)  //!< Bit mask for HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK.

//! @brief Get value of HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK from a register value.
#define BG_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK) >> BP_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK)

//! @brief Format value for bitfield HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK.
#define BF_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK) & BM_HDMI_PHY_MSM_CTRL_MPLL_PH_SEL_CK)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCRPB_STATUS - Scope, Comparator Result and Power Bad Status
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCRPB_STATUS - Scope, Comparator Result and Power Bad Status (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : - Access type : Read-only Address : 0x18 Value at reset : N/A
 */
typedef union _hw_hdmi_phy_scrpb_status
{
    reg16_t U;
    struct _hw_hdmi_phy_scrpb_status_bitfields
    {
        unsigned short CK_SCOPE_OUT : 1; //!< [0] Clock Scope Output Signal
        unsigned short TX_SCOPE_OUT2 : 1; //!< [1] Scoping Value for Lane 2
        unsigned short TX_SCOPE_OUT1 : 1; //!< [2] Scoping Value for Lane 1
        unsigned short TX_SCOPE_OUT0 : 1; //!< [3] Scoping Value for Lane 0
        unsigned short SUP_COMP_RT_RESULT : 1; //!< [4] Support Comparator Resistance Termination Result
        unsigned short RESERVED0 : 1; //!< [5] Reserved
        unsigned short ADC_VAL : 10; //!< [15:6] ADC/DAC bit word (analog signal value)
    } B;
} hw_hdmi_phy_scrpb_status_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCRPB_STATUS register
 */
//@{
#define HW_HDMI_PHY_SCRPB_STATUS_ADDR      (REGS_HDMI_PHY_BASE + 0x18)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCRPB_STATUS bitfields
 */

/*! @name Register HDMI_PHY_SCRPB_STATUS, field CK_SCOPE_OUT[0] (RO)
 *
 * Clock Scope Output Signal
 *
 * Values:
 * - 0 - The clock driver output is not differential.
 * - 1 - The clock driver output is differential.
 */
//@{
#define BP_HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT      (0)      //!< Bit position for HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT.
#define BM_HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT      (0x00000001)  //!< Bit mask for HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT.

//! @brief Get value of HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT from a register value.
#define BG_HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT) >> BP_HDMI_PHY_SCRPB_STATUS_CK_SCOPE_OUT)
//@}

/*! @name Register HDMI_PHY_SCRPB_STATUS, field TX_SCOPE_OUT2[1] (RO)
 *
 * Scoping Value for Lane 2
 *
 * Values:
 * - 0 - The driver output of lane 2 is not differential.
 * - 1 - The driver output of lane 2 is differential.
 */
//@{
#define BP_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2      (1)      //!< Bit position for HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2.
#define BM_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2      (0x00000002)  //!< Bit mask for HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2.

//! @brief Get value of HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2 from a register value.
#define BG_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2) >> BP_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT2)
//@}

/*! @name Register HDMI_PHY_SCRPB_STATUS, field TX_SCOPE_OUT1[2] (RO)
 *
 * Scoping Value for Lane 1
 *
 * Values:
 * - 0 - The driver output of lane 1 is not differential.
 * - 1 - The driver output of lane 1 is differential.
 */
//@{
#define BP_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1      (2)      //!< Bit position for HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1.
#define BM_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1      (0x00000004)  //!< Bit mask for HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1.

//! @brief Get value of HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1 from a register value.
#define BG_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1) >> BP_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT1)
//@}

/*! @name Register HDMI_PHY_SCRPB_STATUS, field TX_SCOPE_OUT0[3] (RO)
 *
 * Scoping Value for Lane 0
 *
 * Values:
 * - 0 - The driver output of lane 0 is not differential.
 * - 1 - The driver output of lane 0 is differential.
 */
//@{
#define BP_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0      (3)      //!< Bit position for HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0.
#define BM_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0      (0x00000008)  //!< Bit mask for HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0.

//! @brief Get value of HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0 from a register value.
#define BG_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0) >> BP_HDMI_PHY_SCRPB_STATUS_TX_SCOPE_OUT0)
//@}

/*! @name Register HDMI_PHY_SCRPB_STATUS, field SUP_COMP_RT_RESULT[4] (RO)
 *
 * Support Comparator Resistance Termination Result This bit represents the result of the comparison
 * process.
 *
 * Values:
 * - 0 - The first input is greater than or equal to the second input.
 * - 1 - The first input is less than the second input.
 */
//@{
#define BP_HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT      (4)      //!< Bit position for HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT.
#define BM_HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT      (0x00000010)  //!< Bit mask for HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT.

//! @brief Get value of HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT from a register value.
#define BG_HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT) >> BP_HDMI_PHY_SCRPB_STATUS_SUP_COMP_RT_RESULT)
//@}

/*! @name Register HDMI_PHY_SCRPB_STATUS, field ADC_VAL[15:6] (RO)
 *
 * ADC/DAC bit word (analog signal value)
 */
//@{
#define BP_HDMI_PHY_SCRPB_STATUS_ADC_VAL      (6)      //!< Bit position for HDMI_PHY_SCRPB_STATUS_ADC_VAL.
#define BM_HDMI_PHY_SCRPB_STATUS_ADC_VAL      (0x0000ffc0)  //!< Bit mask for HDMI_PHY_SCRPB_STATUS_ADC_VAL.

//! @brief Get value of HDMI_PHY_SCRPB_STATUS_ADC_VAL from a register value.
#define BG_HDMI_PHY_SCRPB_STATUS_ADC_VAL(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCRPB_STATUS_ADC_VAL) >> BP_HDMI_PHY_SCRPB_STATUS_ADC_VAL)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_TXTERM - Transmission Termination
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_TXTERM - Transmission Termination (RW)
 *
 * Reset value: 0x0007
 *
 * Register name : TXTERM Access type : Read/write Address : 0x19 Value at reset : 0x0007
 */
typedef union _hw_hdmi_phy_txterm
{
    reg16_t U;
    struct _hw_hdmi_phy_txterm_bitfields
    {
        unsigned short D_TX_TERM : 3; //!< [2:0] Digital Transmission Termination
        unsigned short RESERVED0 : 13; //!< [15:3] Reserved
    } B;
} hw_hdmi_phy_txterm_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_TXTERM register
 */
//@{
#define HW_HDMI_PHY_TXTERM_ADDR      (REGS_HDMI_PHY_BASE + 0x19)
//@}

/*
 * constants & macros for individual HDMI_PHY_TXTERM bitfields
 */

/*! @name Register HDMI_PHY_TXTERM, field D_TX_TERM[2:0] (RW)
 *
 * Digital Transmission Termination This bus defines the transmission termination (resistance)
 * value, which is set by the HDMI controller. The formula for the resistance value is: R = 50 / (1
 * - 0.125 x d_tx_term) This equation is valid only when d_tx_term equals 0-6. 000: 50 Ω 001: 56.14
 * Ω 010: 66.67 Ω 011: 80 Ω 100: 100 Ω 101: 133.33 Ω 110: 200 Ω 111: Open circuit
 */
//@{
#define BP_HDMI_PHY_TXTERM_D_TX_TERM      (0)      //!< Bit position for HDMI_PHY_TXTERM_D_TX_TERM.
#define BM_HDMI_PHY_TXTERM_D_TX_TERM      (0x00000007)  //!< Bit mask for HDMI_PHY_TXTERM_D_TX_TERM.

//! @brief Get value of HDMI_PHY_TXTERM_D_TX_TERM from a register value.
#define BG_HDMI_PHY_TXTERM_D_TX_TERM(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_TXTERM_D_TX_TERM) >> BP_HDMI_PHY_TXTERM_D_TX_TERM)

//! @brief Format value for bitfield HDMI_PHY_TXTERM_D_TX_TERM.
#define BF_HDMI_PHY_TXTERM_D_TX_TERM(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_TXTERM_D_TX_TERM) & BM_HDMI_PHY_TXTERM_D_TX_TERM)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_PTRPT_ENBL - Power Sequence, TX Clock Alignment, Resistance Calibration, Pattern Generator Skip Bit, and TMDS Encoder Enable
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_PTRPT_ENBL - Power Sequence, TX Clock Alignment, Resistance Calibration, Pattern Generator Skip Bit, and TMDS Encoder Enable (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : - Access type : Read/write/override Address : 0x1A Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_ptrpt_enbl
{
    reg16_t U;
    struct _hw_hdmi_phy_ptrpt_enbl_bitfields
    {
        unsigned short REFCLK_ENB : 1; //!< [0] Reference Clock Enable
        unsigned short CKO_WORD_ENB : 1; //!< [1] Output Clock Word Enable
        unsigned short TX_READY : 1; //!< [2] Transmission Ready
        unsigned short TX_CK_ALIGN_ENB : 1; //!< [3] Transmission Clock Alignment Enable
        unsigned short RCAL_ENB : 1; //!< [4] Resistance Calibration Enable
        unsigned short CK_REF_ENB : 1; //!< [5] Clock Reference Enable
        unsigned short PG_SKIP_BIT0 : 1; //!< [6] Pattern Generator Skip Bit 0
        unsigned short PG_SKIP_BIT1 : 1; //!< [7] Pattern Generator Skip Bit 1
        unsigned short PG_SKIP_BIT2 : 1; //!< [8] Pattern Generator Skip Bit 2
        unsigned short RESERVED0 : 6; //!< [14:9] Reserved
        unsigned short OVERRIDE : 1; //!< [15] If the Override bit is set to 1, the working value is the Override bit value, not the registered value.
    } B;
} hw_hdmi_phy_ptrpt_enbl_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_PTRPT_ENBL register
 */
//@{
#define HW_HDMI_PHY_PTRPT_ENBL_ADDR      (REGS_HDMI_PHY_BASE + 0x1a)
//@}

/*
 * constants & macros for individual HDMI_PHY_PTRPT_ENBL bitfields
 */

/*! @name Register HDMI_PHY_PTRPT_ENBL, field REFCLK_ENB[0] (RW)
 *
 * Reference Clock Enable This bit enables or disables the input reference clock.
 *
 * Values:
 * - 0 - Disable the input reference clock, if the Override bit is 0.
 * - 1 - Enable the input reference clock, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB      (0)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_REFCLK_ENB.
#define BM_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB      (0x00000001)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_REFCLK_ENB.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_REFCLK_ENB from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB) >> BP_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_REFCLK_ENB.
#define BF_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB) & BM_HDMI_PHY_PTRPT_ENBL_REFCLK_ENB)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field CKO_WORD_ENB[1] (RW)
 *
 * Output Clock Word Enable This bit enables the output word clock.
 *
 * Values:
 * - 0 - Disable the output clock word, if the Override bit is 0.
 * - 1 - Enable the output clock word, if the Override bit is 0
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB      (1)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB.
#define BM_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB      (0x00000002)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB) >> BP_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB.
#define BF_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB) & BM_HDMI_PHY_PTRPT_ENBL_CKO_WORD_ENB)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field TX_READY[2] (RW)
 *
 * Transmission Ready This bit indicates whether the PHY transmit driver is ready to transmit data.
 *
 * Values:
 * - 0 - PHY transmit driver is not ready to transmit data, if the Override bit is 0.
 * - 1 - PHY transmit driver is ready to transmit data, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_TX_READY      (2)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_TX_READY.
#define BM_HDMI_PHY_PTRPT_ENBL_TX_READY      (0x00000004)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_TX_READY.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_TX_READY from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_TX_READY(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_TX_READY) >> BP_HDMI_PHY_PTRPT_ENBL_TX_READY)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_TX_READY.
#define BF_HDMI_PHY_PTRPT_ENBL_TX_READY(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_TX_READY) & BM_HDMI_PHY_PTRPT_ENBL_TX_READY)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field TX_CK_ALIGN_ENB[3] (RW)
 *
 * Transmission Clock Alignment Enable This bit disables or enables the clock alignment FSM.
 *
 * Values:
 * - 0 - Disable transmission clock alignment FSM, if the Override bit is 0.
 * - 1 - Enable transmission clock alignment FSM, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB      (3)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB.
#define BM_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB      (0x00000008)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB) >> BP_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB.
#define BF_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB) & BM_HDMI_PHY_PTRPT_ENBL_TX_CK_ALIGN_ENB)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field RCAL_ENB[4] (RW)
 *
 * Resistance Calibration Enable This bit enables or disables the resistance clock alignment
 * process.
 *
 * Values:
 * - 0 - Disable the resistance calibration FSM, if the Override bit is 0.
 * - 1 - Enable the resistance calibration FSM, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_RCAL_ENB      (4)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_RCAL_ENB.
#define BM_HDMI_PHY_PTRPT_ENBL_RCAL_ENB      (0x00000010)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_RCAL_ENB.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_RCAL_ENB from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_RCAL_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_RCAL_ENB) >> BP_HDMI_PHY_PTRPT_ENBL_RCAL_ENB)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_RCAL_ENB.
#define BF_HDMI_PHY_PTRPT_ENBL_RCAL_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_RCAL_ENB) & BM_HDMI_PHY_PTRPT_ENBL_RCAL_ENB)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field CK_REF_ENB[5] (RW)
 *
 * Clock Reference Enable This bit powers up the clock alignment and the resistance calibration
 * modules.
 *
 * Values:
 * - 0 - Powers down the clock alignment and the resistance calibration modules, if the Override bit is 0.
 * - 1 - Powers up the clock alignment and the resistance calibration modules, if the Override bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB      (5)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_CK_REF_ENB.
#define BM_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB      (0x00000020)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_CK_REF_ENB.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_CK_REF_ENB from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB) >> BP_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_CK_REF_ENB.
#define BF_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB) & BM_HDMI_PHY_PTRPT_ENBL_CK_REF_ENB)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field PG_SKIP_BIT0[6] (RW)
 *
 * Pattern Generator Skip Bit 0 This bit enables or disables pattern generator skip bit feature for
 * channel 0.
 *
 * Values:
 * - 0 - Disable the pattern generator skip bit feature for the first transmitting channel, if the Override
 *     bit is 0.
 * - 1 - Enable the pattern generator skip bit feature for the first transmitting channel, if the Override
 *     bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0      (6)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0.
#define BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0      (0x00000040)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0 from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0) >> BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0.
#define BF_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0) & BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT0)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field PG_SKIP_BIT1[7] (RW)
 *
 * Pattern Generator Skip Bit 1 This bit enables or disables pattern generator skip bit feature for
 * channel 1.
 *
 * Values:
 * - 0 - Disable the pattern generator skip bit feature for the second transmitting channel, if the Override
 *     bit is 0.
 * - 1 - Enable the pattern generator skip bit feature for the second transmitting channel, if the Override
 *     bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1      (7)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1.
#define BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1      (0x00000080)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1 from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1) >> BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1.
#define BF_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1) & BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT1)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field PG_SKIP_BIT2[8] (RW)
 *
 * Pattern Generator Skip Bit 2 This bit enables or disables pattern generator skip bit feature for
 * channel 2.
 *
 * Values:
 * - 0 - Disable the pattern generator skip bit feature for the third transmitting channel, if the Override
 *     bit is 0.
 * - 1 - Enable the pattern generator skip bit feature for the third transmitting channel, if the Override
 *     bit is 0.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2      (8)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2.
#define BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2      (0x00000100)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2 from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2) >> BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2.
#define BF_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2) & BM_HDMI_PHY_PTRPT_ENBL_PG_SKIP_BIT2)
//@}

/*! @name Register HDMI_PHY_PTRPT_ENBL, field OVERRIDE[15] (RW)
 *
 * If the Override bit is set to 1, the working value is the Override bit value, not the registered
 * value.
 */
//@{
#define BP_HDMI_PHY_PTRPT_ENBL_OVERRIDE      (15)      //!< Bit position for HDMI_PHY_PTRPT_ENBL_OVERRIDE.
#define BM_HDMI_PHY_PTRPT_ENBL_OVERRIDE      (0x00008000)  //!< Bit mask for HDMI_PHY_PTRPT_ENBL_OVERRIDE.

//! @brief Get value of HDMI_PHY_PTRPT_ENBL_OVERRIDE from a register value.
#define BG_HDMI_PHY_PTRPT_ENBL_OVERRIDE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PTRPT_ENBL_OVERRIDE) >> BP_HDMI_PHY_PTRPT_ENBL_OVERRIDE)

//! @brief Format value for bitfield HDMI_PHY_PTRPT_ENBL_OVERRIDE.
#define BF_HDMI_PHY_PTRPT_ENBL_OVERRIDE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PTRPT_ENBL_OVERRIDE) & BM_HDMI_PHY_PTRPT_ENBL_OVERRIDE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_PATTERNGEN - Pattern Generator Mode
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_PATTERNGEN - Pattern Generator Mode (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : PATTERNGEN Access type : Read/write Address : 0x1B Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_patterngen
{
    reg16_t U;
    struct _hw_hdmi_phy_patterngen_bitfields
    {
        unsigned short PG_PAT : 10; //!< [9:0] Pattern Generator Generated Pattern
        unsigned short PG_INSERT_ERR0 : 1; //!< [10] Pattern Generator Insert Error Zero
        unsigned short PG_INSERT_ERR1 : 1; //!< [11] Pattern Generator Insert Error One
        unsigned short PG_INSERT_ERR2 : 1; //!< [12] Pattern Generator Insert Error Two
        unsigned short RESERVED0 : 3; //!< [15:13] Reserved
    } B;
} hw_hdmi_phy_patterngen_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_PATTERNGEN register
 */
//@{
#define HW_HDMI_PHY_PATTERNGEN_ADDR      (REGS_HDMI_PHY_BASE + 0x1b)
//@}

/*
 * constants & macros for individual HDMI_PHY_PATTERNGEN bitfields
 */

/*! @name Register HDMI_PHY_PATTERNGEN, field PG_PAT[9:0] (RW)
 *
 * Pattern Generator Generated Pattern This bus carries the generated pattern from the Pattern
 * Generator module.
 */
//@{
#define BP_HDMI_PHY_PATTERNGEN_PG_PAT      (0)      //!< Bit position for HDMI_PHY_PATTERNGEN_PG_PAT.
#define BM_HDMI_PHY_PATTERNGEN_PG_PAT      (0x000003ff)  //!< Bit mask for HDMI_PHY_PATTERNGEN_PG_PAT.

//! @brief Get value of HDMI_PHY_PATTERNGEN_PG_PAT from a register value.
#define BG_HDMI_PHY_PATTERNGEN_PG_PAT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PATTERNGEN_PG_PAT) >> BP_HDMI_PHY_PATTERNGEN_PG_PAT)

//! @brief Format value for bitfield HDMI_PHY_PATTERNGEN_PG_PAT.
#define BF_HDMI_PHY_PATTERNGEN_PG_PAT(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PATTERNGEN_PG_PAT) & BM_HDMI_PHY_PATTERNGEN_PG_PAT)
//@}

/*! @name Register HDMI_PHY_PATTERNGEN, field PG_INSERT_ERR0[10] (RW)
 *
 * Pattern Generator Insert Error Zero This bit enables or disables error insertion inside the
 * generated pattern for channel 0.
 *
 * Values:
 * - 0 - Do not insert error inside generated pattern for the first transmit channel.
 * - 1 - Insert error inside generated pattern for the first transmit channel.
 */
//@{
#define BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0      (10)      //!< Bit position for HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0.
#define BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0      (0x00000400)  //!< Bit mask for HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0.

//! @brief Get value of HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0 from a register value.
#define BG_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0) >> BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0)

//! @brief Format value for bitfield HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0.
#define BF_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0) & BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR0)
//@}

/*! @name Register HDMI_PHY_PATTERNGEN, field PG_INSERT_ERR1[11] (RW)
 *
 * Pattern Generator Insert Error One This bit enables or disables error insertion inside the
 * generated pattern for channel 1.
 *
 * Values:
 * - 0 - Do not insert error inside generated pattern for the second transmit channel.
 * - 1 - Insert error inside generated pattern for the second transmit channel.
 */
//@{
#define BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1      (11)      //!< Bit position for HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1.
#define BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1      (0x00000800)  //!< Bit mask for HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1.

//! @brief Get value of HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1 from a register value.
#define BG_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1) >> BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1)

//! @brief Format value for bitfield HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1.
#define BF_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1) & BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR1)
//@}

/*! @name Register HDMI_PHY_PATTERNGEN, field PG_INSERT_ERR2[12] (RW)
 *
 * Pattern Generator Insert Error Two This bit enables or disables error insertion inside the
 * generated pattern for channel 2.
 *
 * Values:
 * - 0 - Do not insert error inside generated pattern for the third transmit channel.
 * - 1 - Insert error inside generated pattern for the third transmit channel.
 */
//@{
#define BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2      (12)      //!< Bit position for HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2.
#define BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2      (0x00001000)  //!< Bit mask for HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2.

//! @brief Get value of HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2 from a register value.
#define BG_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2) >> BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2)

//! @brief Format value for bitfield HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2.
#define BF_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2) & BM_HDMI_PHY_PATTERNGEN_PG_INSERT_ERR2)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SDCAP_MODE - The Soft-Reset and DAC Enable, Clock Alignment and PG Mode
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SDCAP_MODE - The Soft-Reset and DAC Enable, Clock Alignment and PG Mode (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : - Access type : Read/write Address : 0x1C Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_sdcap_mode
{
    reg16_t U;
    struct _hw_hdmi_phy_sdcap_mode_bitfields
    {
        unsigned short SOFT_RESET : 1; //!< [0] Soft Reset
        unsigned short ADC_ENB : 1; //!< [1] Analog-to-Digital Converter Enable
        unsigned short TX_CK_ALIGN_MODE : 1; //!< [2] Transmission Clock Alignment Mode
        unsigned short PG_MODE0 : 3; //!< [5:3] Pattern Generator Mode 0
        unsigned short PG_MODE1 : 3; //!< [8:6] Pattern Generator Mode 1
        unsigned short PG_MODE2 : 3; //!< [11:9] Pattern Generator Mode 2
        unsigned short RESERVED0 : 4; //!< [15:12] Reserved
    } B;
} hw_hdmi_phy_sdcap_mode_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SDCAP_MODE register
 */
//@{
#define HW_HDMI_PHY_SDCAP_MODE_ADDR      (REGS_HDMI_PHY_BASE + 0x1c)
//@}

/*
 * constants & macros for individual HDMI_PHY_SDCAP_MODE bitfields
 */

/*! @name Register HDMI_PHY_SDCAP_MODE, field SOFT_RESET[0] (RW)
 *
 * Soft Reset This bit enables or disables the soft-reset feature.
 *
 * Values:
 * - 0 - Do not perform a soft reset.
 * - 1 - Perform a soft reset by resetting all the system FSMs except the I 2 C and Control Register modules.
 */
//@{
#define BP_HDMI_PHY_SDCAP_MODE_SOFT_RESET      (0)      //!< Bit position for HDMI_PHY_SDCAP_MODE_SOFT_RESET.
#define BM_HDMI_PHY_SDCAP_MODE_SOFT_RESET      (0x00000001)  //!< Bit mask for HDMI_PHY_SDCAP_MODE_SOFT_RESET.

//! @brief Get value of HDMI_PHY_SDCAP_MODE_SOFT_RESET from a register value.
#define BG_HDMI_PHY_SDCAP_MODE_SOFT_RESET(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SDCAP_MODE_SOFT_RESET) >> BP_HDMI_PHY_SDCAP_MODE_SOFT_RESET)

//! @brief Format value for bitfield HDMI_PHY_SDCAP_MODE_SOFT_RESET.
#define BF_HDMI_PHY_SDCAP_MODE_SOFT_RESET(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SDCAP_MODE_SOFT_RESET) & BM_HDMI_PHY_SDCAP_MODE_SOFT_RESET)
//@}

/*! @name Register HDMI_PHY_SDCAP_MODE, field ADC_ENB[1] (RW)
 *
 * Analog-to-Digital Converter Enable This bit enables or disables the analog-to-digital converter.
 *
 * Values:
 * - 0 - Disable the analog-to-digital converter.
 * - 1 - Enable the analog-to-digital converter, which is used in the Resistance Calibration module.
 */
//@{
#define BP_HDMI_PHY_SDCAP_MODE_ADC_ENB      (1)      //!< Bit position for HDMI_PHY_SDCAP_MODE_ADC_ENB.
#define BM_HDMI_PHY_SDCAP_MODE_ADC_ENB      (0x00000002)  //!< Bit mask for HDMI_PHY_SDCAP_MODE_ADC_ENB.

//! @brief Get value of HDMI_PHY_SDCAP_MODE_ADC_ENB from a register value.
#define BG_HDMI_PHY_SDCAP_MODE_ADC_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SDCAP_MODE_ADC_ENB) >> BP_HDMI_PHY_SDCAP_MODE_ADC_ENB)

//! @brief Format value for bitfield HDMI_PHY_SDCAP_MODE_ADC_ENB.
#define BF_HDMI_PHY_SDCAP_MODE_ADC_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SDCAP_MODE_ADC_ENB) & BM_HDMI_PHY_SDCAP_MODE_ADC_ENB)
//@}

/*! @name Register HDMI_PHY_SDCAP_MODE, field TX_CK_ALIGN_MODE[2] (RW)
 *
 * Transmission Clock Alignment Mode This bit selects the Transmission Clock Alignment mode.
 *
 * Values:
 * - 0 - Align the three lanes based on lane 1.
 * - 1 - Align each of the three lanes separately in the following order: lane 2, lane 0, then lane 1.
 */
//@{
#define BP_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE      (2)      //!< Bit position for HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE.
#define BM_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE      (0x00000004)  //!< Bit mask for HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE.

//! @brief Get value of HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE from a register value.
#define BG_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE) >> BP_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE)

//! @brief Format value for bitfield HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE.
#define BF_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE) & BM_HDMI_PHY_SDCAP_MODE_TX_CK_ALIGN_MODE)
//@}

/*! @name Register HDMI_PHY_SDCAP_MODE, field PG_MODE0[5:3] (RW)
 *
 * Pattern Generator Mode 0 This bus is used to select the mode of the Pattern Generator module for
 * channel 0.
 *
 * Values:
 * - 000 - Disable the Pattern Generator module.
 * - 001 - Enable the Pattern Generator module and generate a sequence of patterns for the first channel using
 *     LFSR 15 equation (for example, x15 + x14 + 1).
 * - 010 - Enable the Pattern Generator module and generate a sequence of patterns for the first channel using
 *     LFSR 7 equation (for example, x7 + x6 + 1).
 * - 011 - Enable the Pattern Generator module and generate a sequence of patterns for the first channel with
 *     the fixed word, which is saved inside the pg_pat[9:0] field of the PATTERNGEN register.
 * - 100 - Enable the Pattern Generator module and generate a sequence of patterns for the first channel with
 *     DC-balanced word (for example, 0's or 1's and their inverted values).
 * - 101 - Enable the Pattern Generator module and generate a sequence of patterns for the first channel with
 *     fixed pattern using word of 0's word, 1's word, random word, the saved pattern inside the
 *     pg_pat[9:0] field of the PATTERNGEN register, and the inverted pg_pat[9:0] values (for
 *     example, 9 bits of 0's, 9 bits of 1's, 3FF, pg_pat[9:0], ~ pg_pat[9:0]).
 * - 110 - Reserved
 * - 111 - Reserved
 */
//@{
#define BP_HDMI_PHY_SDCAP_MODE_PG_MODE0      (3)      //!< Bit position for HDMI_PHY_SDCAP_MODE_PG_MODE0.
#define BM_HDMI_PHY_SDCAP_MODE_PG_MODE0      (0x00000038)  //!< Bit mask for HDMI_PHY_SDCAP_MODE_PG_MODE0.

//! @brief Get value of HDMI_PHY_SDCAP_MODE_PG_MODE0 from a register value.
#define BG_HDMI_PHY_SDCAP_MODE_PG_MODE0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SDCAP_MODE_PG_MODE0) >> BP_HDMI_PHY_SDCAP_MODE_PG_MODE0)

//! @brief Format value for bitfield HDMI_PHY_SDCAP_MODE_PG_MODE0.
#define BF_HDMI_PHY_SDCAP_MODE_PG_MODE0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SDCAP_MODE_PG_MODE0) & BM_HDMI_PHY_SDCAP_MODE_PG_MODE0)
//@}

/*! @name Register HDMI_PHY_SDCAP_MODE, field PG_MODE1[8:6] (RW)
 *
 * Pattern Generator Mode 1 This bus is used to select the mode of the Pattern Generator module for
 * channel 1.
 *
 * Values:
 * - 000 - Disable the Pattern Generator module.
 * - 001 - Enable the Pattern Generator module and generate a sequence of patterns for the second channel using
 *     LFSR 15 equation (for example, x15 + x14 + 1).
 * - 010 - second the Pattern Generator module and generate a sequence of patterns for the first channel using
 *     LFSR 7 equation (for example, x7 + x6 + 1).
 * - 011 - Enable the Pattern Generator module and generate a sequence of patterns for the second channel with
 *     the fixed word, which is saved inside the pg_pat[9:0] field of the PATTERNGEN register.
 * - 100 - Enable the Pattern Generator module and generate a sequence of patterns for the second channel with
 *     DC-balanced word (for example, 0's or 1's and their inverted values).
 * - 101 - Enable the Pattern Generator module and generate a sequence of patterns for the second channel with
 *     fixed pattern using word of 0's word, 1's word, random word, the saved pattern inside the
 *     pg_pat[9:0] field of the PATTERNGEN register, and the inverted pg_pat[9:0] values (for
 *     example, 9 bits of 0's, 9 bits of 1's, 3FF, pg_pat[9:0], ~ pg_pat[9:0]).
 * - 110 - Reserved
 * - 111 - Reserved
 */
//@{
#define BP_HDMI_PHY_SDCAP_MODE_PG_MODE1      (6)      //!< Bit position for HDMI_PHY_SDCAP_MODE_PG_MODE1.
#define BM_HDMI_PHY_SDCAP_MODE_PG_MODE1      (0x000001c0)  //!< Bit mask for HDMI_PHY_SDCAP_MODE_PG_MODE1.

//! @brief Get value of HDMI_PHY_SDCAP_MODE_PG_MODE1 from a register value.
#define BG_HDMI_PHY_SDCAP_MODE_PG_MODE1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SDCAP_MODE_PG_MODE1) >> BP_HDMI_PHY_SDCAP_MODE_PG_MODE1)

//! @brief Format value for bitfield HDMI_PHY_SDCAP_MODE_PG_MODE1.
#define BF_HDMI_PHY_SDCAP_MODE_PG_MODE1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SDCAP_MODE_PG_MODE1) & BM_HDMI_PHY_SDCAP_MODE_PG_MODE1)
//@}

/*! @name Register HDMI_PHY_SDCAP_MODE, field PG_MODE2[11:9] (RW)
 *
 * Pattern Generator Mode 2 This bus is used to select the mode of the Pattern Generator module for
 * channel 2.
 *
 * Values:
 * - 000 - Disable the Pattern Generator module.
 * - 001 - Enable the Pattern Generator module and generate a sequence of patterns for the third channel using
 *     LFSR 15 equation (for example, x15 + x14 + 1).
 * - 010 - Enable the Pattern Generator module and generate a sequence of patterns for the third channel using
 *     LFSR 7 equation (for example, x7 + x6 + 1).
 * - 011 - Enable the Pattern Generator module and generate a sequence of patterns for the third channel with
 *     the fixed word, which is saved inside the pg_pat[9:0] field of the PATTERNGEN register.
 * - 100 - Enable the Pattern Generator module and generate a sequence of patterns for the third channel with
 *     DC-balanced word (for example, 0's or 1's and their inverted values).
 * - 101 - Enable the Pattern Generator module and generate a sequence of patterns for the third channel with
 *     fixed pattern using word of 0's word, 1's word, random word, the saved pattern inside the
 *     pg_pat[9:0] field of the PATTERNGEN register, and the inverted pg_pat[9:0] values (for
 *     example, 9 bits of 0's, 9 bits of 1's, 3FF, pg_pat[9:0], ~ pg_pat[9:0]).
 * - 110 - Reserved
 * - 111 - Reserved
 */
//@{
#define BP_HDMI_PHY_SDCAP_MODE_PG_MODE2      (9)      //!< Bit position for HDMI_PHY_SDCAP_MODE_PG_MODE2.
#define BM_HDMI_PHY_SDCAP_MODE_PG_MODE2      (0x00000e00)  //!< Bit mask for HDMI_PHY_SDCAP_MODE_PG_MODE2.

//! @brief Get value of HDMI_PHY_SDCAP_MODE_PG_MODE2 from a register value.
#define BG_HDMI_PHY_SDCAP_MODE_PG_MODE2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SDCAP_MODE_PG_MODE2) >> BP_HDMI_PHY_SDCAP_MODE_PG_MODE2)

//! @brief Format value for bitfield HDMI_PHY_SDCAP_MODE_PG_MODE2.
#define BF_HDMI_PHY_SDCAP_MODE_PG_MODE2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SDCAP_MODE_PG_MODE2) & BM_HDMI_PHY_SDCAP_MODE_PG_MODE2)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPEMODE - Scope Mode register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPEMODE - Scope Mode register (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPEMODE Access type : Read/write Address : 0x1D Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopemode
{
    reg16_t U;
    struct _hw_hdmi_phy_scopemode_bitfields
    {
        unsigned short SCOPE_SAMPLE_CNT : 10; //!< [9:0] Scope Sample Counter
        unsigned short SCOPE_ENB0 : 1; //!< [10] Scope Enable 0
        unsigned short SCOPE_ENB1 : 1; //!< [11] Scope Enable 1
        unsigned short SCOPE_ENB2 : 1; //!< [12] Scope Enable 2
        unsigned short CK_SCOPE_ENB : 1; //!< [13] Clock Scope Enable
        unsigned short RESERVED0 : 2; //!< [15:14] Reserved
    } B;
} hw_hdmi_phy_scopemode_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPEMODE register
 */
//@{
#define HW_HDMI_PHY_SCOPEMODE_ADDR      (REGS_HDMI_PHY_BASE + 0x1d)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPEMODE bitfields
 */

/*! @name Register HDMI_PHY_SCOPEMODE, field SCOPE_SAMPLE_CNT[9:0] (RW)
 *
 * Scope Sample Counter Indicates the number of samples that will be counted (should be multiple of
 * the LFSR length). This count includes only the LSB bits; if the LFSR15 was used, you must program
 * the new bits under the 0x24 register.
 */
//@{
#define BP_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT      (0)      //!< Bit position for HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT.
#define BM_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT      (0x000003ff)  //!< Bit mask for HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT.

//! @brief Get value of HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT from a register value.
#define BG_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT) >> BP_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT)

//! @brief Format value for bitfield HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT.
#define BF_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT) & BM_HDMI_PHY_SCOPEMODE_SCOPE_SAMPLE_CNT)
//@}

/*! @name Register HDMI_PHY_SCOPEMODE, field SCOPE_ENB0[10] (RW)
 *
 * Scope Enable 0 This bit enables or disables the tracing of 1's on channel 0.
 *
 * Values:
 * - 0 - Disable the tracing of 1's on the first channel.
 * - 1 - Enable the tracing of 1's on the first channel.
 */
//@{
#define BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB0      (10)      //!< Bit position for HDMI_PHY_SCOPEMODE_SCOPE_ENB0.
#define BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB0      (0x00000400)  //!< Bit mask for HDMI_PHY_SCOPEMODE_SCOPE_ENB0.

//! @brief Get value of HDMI_PHY_SCOPEMODE_SCOPE_ENB0 from a register value.
#define BG_HDMI_PHY_SCOPEMODE_SCOPE_ENB0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB0) >> BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB0)

//! @brief Format value for bitfield HDMI_PHY_SCOPEMODE_SCOPE_ENB0.
#define BF_HDMI_PHY_SCOPEMODE_SCOPE_ENB0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB0) & BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB0)
//@}

/*! @name Register HDMI_PHY_SCOPEMODE, field SCOPE_ENB1[11] (RW)
 *
 * Scope Enable 1 This bit enables or disables the tracing of 1's on channel 1.
 *
 * Values:
 * - 0 - Disable the tracing of 1's on the second channel.
 * - 1 - Enable the tracing of 1's on the second channel.
 */
//@{
#define BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB1      (11)      //!< Bit position for HDMI_PHY_SCOPEMODE_SCOPE_ENB1.
#define BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB1      (0x00000800)  //!< Bit mask for HDMI_PHY_SCOPEMODE_SCOPE_ENB1.

//! @brief Get value of HDMI_PHY_SCOPEMODE_SCOPE_ENB1 from a register value.
#define BG_HDMI_PHY_SCOPEMODE_SCOPE_ENB1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB1) >> BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB1)

//! @brief Format value for bitfield HDMI_PHY_SCOPEMODE_SCOPE_ENB1.
#define BF_HDMI_PHY_SCOPEMODE_SCOPE_ENB1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB1) & BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB1)
//@}

/*! @name Register HDMI_PHY_SCOPEMODE, field SCOPE_ENB2[12] (RW)
 *
 * Scope Enable 2 This bit enables or disables the tracing of 1's on channel 2.
 *
 * Values:
 * - 0 - Disable the tracing of 1's on the third channel.
 * - 1 - Enable the tracing of 1's on the third channel.
 */
//@{
#define BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB2      (12)      //!< Bit position for HDMI_PHY_SCOPEMODE_SCOPE_ENB2.
#define BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB2      (0x00001000)  //!< Bit mask for HDMI_PHY_SCOPEMODE_SCOPE_ENB2.

//! @brief Get value of HDMI_PHY_SCOPEMODE_SCOPE_ENB2 from a register value.
#define BG_HDMI_PHY_SCOPEMODE_SCOPE_ENB2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB2) >> BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB2)

//! @brief Format value for bitfield HDMI_PHY_SCOPEMODE_SCOPE_ENB2.
#define BF_HDMI_PHY_SCOPEMODE_SCOPE_ENB2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SCOPEMODE_SCOPE_ENB2) & BM_HDMI_PHY_SCOPEMODE_SCOPE_ENB2)
//@}

/*! @name Register HDMI_PHY_SCOPEMODE, field CK_SCOPE_ENB[13] (RW)
 *
 * Clock Scope Enable This bit enables or disables the tracing of 1's on the clock channel.
 *
 * Values:
 * - 0 - Disable the tracing of 1's on the clock.
 * - 1 - Enable the tracing of 1's on the clock.
 */
//@{
#define BP_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB      (13)      //!< Bit position for HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB.
#define BM_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB      (0x00002000)  //!< Bit mask for HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB.

//! @brief Get value of HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB from a register value.
#define BG_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB) >> BP_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB)

//! @brief Format value for bitfield HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB.
#define BF_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB) & BM_HDMI_PHY_SCOPEMODE_CK_SCOPE_ENB)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_DIGTXMODE - Digital Transmission Mode
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_DIGTXMODE - Digital Transmission Mode (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : DIGTXMODE Access type : Read/write Address : 0x1E Value at reset : 0x0000
 * dtb_select[6:0] The dtb_select[6:0] encodings for the bit pairs are as follows: Power Sequence
 * 0x00: dtb[1] = pll_pwr_on and dtb[0] = pll_rst 0x01: dtb[1] = pll_pwr_on and dtb[0] =
 * pll_gear_shift 0x02: dtb[1] = pll_pwr_on and dtb[0] = pll_drv_ana 0x03: dtb[1] = pll_pwr_on and
 * dtb[0] = cko_word_enb 0x04: dtb[1] = pll_pwr_on and dtb[0] = tx_ready 0x05: dtb[1] = mpll_pwr_on
 * and dtb[0] = mpll_rst 0x06: dtb[1] = mpll_pwr_on and dtb[0] = mpll_gear_shift 0x07: dtb[1] =
 * mpll_pwr_on and dtb[0] = mpll_drv_ana 0x08: dtb[1] = mpll_pwr_on and dtb[0] = cko_word_enb 0x09:
 * dtb[1] = mpll_pwr_on and dtb[0] = tx_ready 0x0A: dtb[1] = mpll_pwr_on and dtb[0] = tx_ser_div_en1
 * 0x0B: dtb[1] = mpll_pwr_on and dtb[0] = tx_ser_clk_en1 0x0C: dtb[1] = ck_ref_enb and dtb[0] =
 * refclk_enb 0x0D: dtb[1] = cko_word_enb and dtb[0] = refclk_enb Transmission Clock Alignment 0x0E:
 * Reserved 0x0F: dtb[1] = tx_ck_align_enb and dtb[0] = tx_ser_clk_kill0 0x10: dtb[1] =
 * tx_ck_align_enb and dtb[0] = tx_ser_clk_kill1 0x11: dtb[1] = tx_ck_align_enb and dtb[0] =
 * tx_ser_clk_kill2 0x12: dtb[1] = tx_ck_align_enb and dtb[0] = tx_ck_align_done Resistance
 * Calibration and Analog-to-Digital Converter 0x13: Reserved 0x14: dtb[1] = ck_rescal[6] and dtb[0]
 * = ck_rescal[5] 0x15: dtb[1] = ck_rescal[4] and dtb[0] = ck_rescal[3] 0x16: dtb[1] = ck_rescal[2]
 * and dtb[0] = ck_rescal[1] 0x17: dtb[1] = ck_rescal[0] and dtb[0] = sup_comp_mode 0x18: dtb[1] =
 * sup_comp_rt_result and dtb[0] = sup_comp_rt_r 0x19: dtb[1] = sup_dac_n[7] and dtb[0] =
 * sup_dac_n[6] 0x1A: dtb[1] = sup_dac_n[5] and dtb[0] = sup_dac_n[4] 0x1B: dtb[1] = sup_dac_n[3]
 * and dtb[0] = sup_dac_n[2] 0x1C: dtb[1] = sup_dac_n[1] and dtb[0] = sup_dac_n[0] 0x1D: dtb[1] =
 * sup_dac_th_n[2] and dtb[0] = sup_dac_th_n[1] 0x1E: dtb[1] = sup_dac_th_n[0] and dtb[0] =
 * rescal_rep[6] 0x1F: dtb[1] = rescal_rep[5] and dtb[0] = rescal_rep[4] 0x20: dtb[1] =
 * rescal_rep[3] and dtb[0] = rescal_rep[2] 0x21: dtb[1] = rescal_rep[1] and dtb[0] = rescal_rep[0]
 * 0x22: dtb[1] = rcal_enb and dtb[0] = rcal_adc_done 0x23: dtb[1] = sup_comp_rt_pwron and dtb[0] =
 * rcal_adc_done 0x24: Reserved 0x25: Reserved 0x26: Reserved 0x27: Reserved TMDS Data Pattern 0x28:
 * dtb[1] = tmds_data2[9] and dtb[0] = tmds_data2[8] 0x29: dtb[1] = tmds_data2[8] and dtb[0] =
 * tmds_data2[7] 0x2A: dtb[1] = tmds_data2[7] and dtb[0] = tmds_data2[6] 0x2B: dtb[1] =
 * tmds_data2[6] and dtb[0] = tmds_data2[5] 0x2C: dtb[1] = tmds_data2[5] and dtb[0] = tmds_data2[4]
 * 0x2D: dtb[1] = tmds_data2[4] and dtb[0] = tmds_data2[3] 0x2E: dtb[1] = tmds_data2[3] and dtb[0] =
 * tmds_data2[2] 0x2F: dtb[1] = tmds_data2[2] and dtb[0] = tmds_data2[1] 0x30: dtb[1] =
 * tmds_data2[1] and dtb[0] = tmds_data2[0] 0x31: dtb[1] = tmds_data2[0] and dtb[0] = tmds_data1[9]
 * 0x32: dtb[1] = tmds_data1[9] and dtb[0] = tmds_data1[8] 0x33: dtb[1] = tmds_data1[8] and dtb[0] =
 * tmds_data1[7] 0x34: dtb[1] = tmds_data1[7] and dtb[0] = tmds_data1[6] 0x35: dtb[1] =
 * tmds_data1[6] and dtb[0] = tmds_data1[5] 0x36: dtb[1] = tmds_data1[5] and dtb[0] = tmds_data1[4]
 * 0x37: dtb[1] = tmds_data1[4] and dtb[0] = tmds_data1[3] 0x38: dtb[1] = tmds_data1[3] and dtb[0] =
 * tmds_data1[2] 0x39: dtb[1] = tmds_data1[2] and dtb[0] = tmds_data1[1] 0x3A: dtb[1] =
 * tmds_data1[1] and dtb[0] = tmds_data1[0] 0x3B: dtb[1] = tmds_data1[0] and dtb[0] = tmds_data0[9]
 * 0x3C: dtb[1] = tmds_data0[9] and dtb[0] = tmds_data0[8] 0x3D: dtb[1] = tmds_data0[8] and dtb[0] =
 * tmds_data0[7] 0x3E: dtb[1] = tmds_data0[7] and dtb[0] = tmds_data0[6] 0x3F: dtb[1] =
 * tmds_data0[6] and dtb[0] = tmds_data0[5] 0x40: dtb[1] = tmds_data0[5] and dtb[0] = tmds_data0[4]
 * 0x41: dtb[1] = tmds_data0[4] and dtb[0] = tmds_data0[3] 0x42: dtb[1] = tmds_data0[3] and dtb[0] =
 * tmds_data0[2] 0x43: dtb[1] = tmds_data0[2] and dtb[0] = tmds_data0[1] 0x44: dtb[1] =
 * tmds_data0[1] and dtb[0] = tmds_data0[0] 0x45: dtb[1] = tmds_data0[0] and dtb[0] = tx_ready
 * Pattern Generator 0x46: dtb[1] = tmds_data2[0] and dtb[0] = pg_dtb2 0x47: dtb[1] = tmds_data1[0]
 * and dtb[0] = pg_dtb1 0x48: dtb[1] = tmds_data0[0] and dtb[0] = pg_dtb0 0x49: dtb[1] = pg_dtb2 and
 * dtb[0] = pg_dtb0 0x4A: dtb[1] = pg_dtb1 and dtb[0] = pg_dtb0 0x4B: Reserved 0x4C: Reserved 0x4D:
 * Reserved 0x4E: Reserved 0x4F: Reserved Scope 0x50: dtb[1] = scope_enb2 and dtb[0] = scope_done2
 * 0x51: dtb[1] = scope_enb1 and dtb[0] = scope_done1 0x52: dtb[1] = scope_enb0 and dtb[0] =
 * scope_done0 0x53: dtb[1] = ck_scope_enb and dtb[0] = ck_scope_done 0x54: dtb[1] = scope_enb2 and
 * dtb[0] = tx_scope_out2 0x55: dtb[1] = scope_enb1 and dtb[0] = tx_scope_out1 0x56: dtb[1] =
 * scope_enb0 and dtb[0] = tx_scope_out0 0x57: Reserved 0x58: Reserved 0x59: Reserved I 2 C 0x5A:
 * dtb[1] = start_cond and dtb[0] = cregs_write (Not stored in the control register.) 0x5B: dtb[1] =
 * sda_pull_dn_n and dtb[0] = cregs_ack (Not stored in the control register.) 0x5C: dtb[1] =
 * cregs_read and dtb[0] = cregs_rd_data[0] (Not stored in the control register.) 0x5D: Reserved
 * 0x5E: Reserved 0x5F: Reserved 0x60: Reserved 0x61: Reserved 0x62: Reserved 0x63: Reserved Rx
 * Sense 0x64: dtb[1] = rx_sense of clock driver and dtb[0] = rx_sense of CH2's driver 0x65: dtb[1]
 * = rx_sense of CH1's driver and dtb[0] = rx_sense of CH0's driver 0x66: -
 */
typedef union _hw_hdmi_phy_digtxmode
{
    reg16_t U;
    struct _hw_hdmi_phy_digtxmode_bitfields
    {
        unsigned short SKIP_BIT0 : 1; //!< [0] Skip Bit 0
        unsigned short SKIP_BIT1 : 1; //!< [1] Skip Bit 1
        unsigned short SKIP_BIT2 : 1; //!< [2] Skip Bit 2
        unsigned short CKO_WORD_DIV_ENB : 1; //!< [3] Clock Output Word Divider Enable
        unsigned short INVERT_DATA0 : 1; //!< [4] Inverter Data 0
        unsigned short INVERT_DATA1 : 1; //!< [5] Inverter Data 1
        unsigned short INVERT_DATA2 : 1; //!< [6] Inverter Data 2
        unsigned short DTB_SELECT : 6; //!< [12:7] Debug Test Bus Select
        unsigned short RESERVED0 : 3; //!< [15:13] Reserved
    } B;
} hw_hdmi_phy_digtxmode_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_DIGTXMODE register
 */
//@{
#define HW_HDMI_PHY_DIGTXMODE_ADDR      (REGS_HDMI_PHY_BASE + 0x1e)
//@}

/*
 * constants & macros for individual HDMI_PHY_DIGTXMODE bitfields
 */

/*! @name Register HDMI_PHY_DIGTXMODE, field SKIP_BIT0[0] (RW)
 *
 * Skip Bit 0 This bit enables or disables skipping of the ninth bit of the transmitted pattern on
 * channel 0.
 *
 * Values:
 * - 0 - Disable the skipping feature on the first channel.
 * - 1 - Enable the skipping feature on the first channel.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_SKIP_BIT0      (0)      //!< Bit position for HDMI_PHY_DIGTXMODE_SKIP_BIT0.
#define BM_HDMI_PHY_DIGTXMODE_SKIP_BIT0      (0x00000001)  //!< Bit mask for HDMI_PHY_DIGTXMODE_SKIP_BIT0.

//! @brief Get value of HDMI_PHY_DIGTXMODE_SKIP_BIT0 from a register value.
#define BG_HDMI_PHY_DIGTXMODE_SKIP_BIT0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_SKIP_BIT0) >> BP_HDMI_PHY_DIGTXMODE_SKIP_BIT0)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_SKIP_BIT0.
#define BF_HDMI_PHY_DIGTXMODE_SKIP_BIT0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_SKIP_BIT0) & BM_HDMI_PHY_DIGTXMODE_SKIP_BIT0)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field SKIP_BIT1[1] (RW)
 *
 * Skip Bit 1 This bit enables or disables skipping of the ninth bit of the transmitted pattern on
 * channel 1.
 *
 * Values:
 * - 0 - Disable the skipping feature on the second channel.
 * - 1 - Enable the skipping feature on the second channel.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_SKIP_BIT1      (1)      //!< Bit position for HDMI_PHY_DIGTXMODE_SKIP_BIT1.
#define BM_HDMI_PHY_DIGTXMODE_SKIP_BIT1      (0x00000002)  //!< Bit mask for HDMI_PHY_DIGTXMODE_SKIP_BIT1.

//! @brief Get value of HDMI_PHY_DIGTXMODE_SKIP_BIT1 from a register value.
#define BG_HDMI_PHY_DIGTXMODE_SKIP_BIT1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_SKIP_BIT1) >> BP_HDMI_PHY_DIGTXMODE_SKIP_BIT1)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_SKIP_BIT1.
#define BF_HDMI_PHY_DIGTXMODE_SKIP_BIT1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_SKIP_BIT1) & BM_HDMI_PHY_DIGTXMODE_SKIP_BIT1)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field SKIP_BIT2[2] (RW)
 *
 * Skip Bit 2 This bit enables or disables skipping of the ninth bit of the transmitted pattern on
 * channel 2.
 *
 * Values:
 * - 0 - Disable the skipping feature on the third channel.
 * - 1 - Enable the skipping feature on the third channel.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_SKIP_BIT2      (2)      //!< Bit position for HDMI_PHY_DIGTXMODE_SKIP_BIT2.
#define BM_HDMI_PHY_DIGTXMODE_SKIP_BIT2      (0x00000004)  //!< Bit mask for HDMI_PHY_DIGTXMODE_SKIP_BIT2.

//! @brief Get value of HDMI_PHY_DIGTXMODE_SKIP_BIT2 from a register value.
#define BG_HDMI_PHY_DIGTXMODE_SKIP_BIT2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_SKIP_BIT2) >> BP_HDMI_PHY_DIGTXMODE_SKIP_BIT2)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_SKIP_BIT2.
#define BF_HDMI_PHY_DIGTXMODE_SKIP_BIT2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_SKIP_BIT2) & BM_HDMI_PHY_DIGTXMODE_SKIP_BIT2)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field CKO_WORD_DIV_ENB[3] (RW)
 *
 * Clock Output Word Divider Enable This bit enables or disables the output clock word divider.
 *
 * Values:
 * - 0 - Disable the output clock divider.
 * - 1 - Enable the output clock divider.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB      (3)      //!< Bit position for HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB.
#define BM_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB      (0x00000008)  //!< Bit mask for HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB.

//! @brief Get value of HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB from a register value.
#define BG_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB) >> BP_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB.
#define BF_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB) & BM_HDMI_PHY_DIGTXMODE_CKO_WORD_DIV_ENB)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field INVERT_DATA0[4] (RW)
 *
 * Inverter Data 0 This bit enables or disables the inverting feature for the transmitted pattern on
 * channel 0.
 *
 * Values:
 * - 0 - Disable the inverting feature on the first channel.
 * - 1 - Enable the inverting feature on the first channel.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_INVERT_DATA0      (4)      //!< Bit position for HDMI_PHY_DIGTXMODE_INVERT_DATA0.
#define BM_HDMI_PHY_DIGTXMODE_INVERT_DATA0      (0x00000010)  //!< Bit mask for HDMI_PHY_DIGTXMODE_INVERT_DATA0.

//! @brief Get value of HDMI_PHY_DIGTXMODE_INVERT_DATA0 from a register value.
#define BG_HDMI_PHY_DIGTXMODE_INVERT_DATA0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_INVERT_DATA0) >> BP_HDMI_PHY_DIGTXMODE_INVERT_DATA0)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_INVERT_DATA0.
#define BF_HDMI_PHY_DIGTXMODE_INVERT_DATA0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_INVERT_DATA0) & BM_HDMI_PHY_DIGTXMODE_INVERT_DATA0)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field INVERT_DATA1[5] (RW)
 *
 * Inverter Data 1 This bit enables or disables the inverting feature for the transmitted pattern on
 * channel 1.
 *
 * Values:
 * - 0 - Disable the inverting feature on the second channel.
 * - 1 - Enable the inverting feature on the second channel.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_INVERT_DATA1      (5)      //!< Bit position for HDMI_PHY_DIGTXMODE_INVERT_DATA1.
#define BM_HDMI_PHY_DIGTXMODE_INVERT_DATA1      (0x00000020)  //!< Bit mask for HDMI_PHY_DIGTXMODE_INVERT_DATA1.

//! @brief Get value of HDMI_PHY_DIGTXMODE_INVERT_DATA1 from a register value.
#define BG_HDMI_PHY_DIGTXMODE_INVERT_DATA1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_INVERT_DATA1) >> BP_HDMI_PHY_DIGTXMODE_INVERT_DATA1)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_INVERT_DATA1.
#define BF_HDMI_PHY_DIGTXMODE_INVERT_DATA1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_INVERT_DATA1) & BM_HDMI_PHY_DIGTXMODE_INVERT_DATA1)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field INVERT_DATA2[6] (RW)
 *
 * Inverter Data 2 This bit enables or disables the inverting feature for the transmitted pattern on
 * channel 2.
 *
 * Values:
 * - 0 - Disable the inverting feature on the third channel.
 * - 1 - Enable the inverting feature on the third channel.
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_INVERT_DATA2      (6)      //!< Bit position for HDMI_PHY_DIGTXMODE_INVERT_DATA2.
#define BM_HDMI_PHY_DIGTXMODE_INVERT_DATA2      (0x00000040)  //!< Bit mask for HDMI_PHY_DIGTXMODE_INVERT_DATA2.

//! @brief Get value of HDMI_PHY_DIGTXMODE_INVERT_DATA2 from a register value.
#define BG_HDMI_PHY_DIGTXMODE_INVERT_DATA2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_INVERT_DATA2) >> BP_HDMI_PHY_DIGTXMODE_INVERT_DATA2)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_INVERT_DATA2.
#define BF_HDMI_PHY_DIGTXMODE_INVERT_DATA2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_INVERT_DATA2) & BM_HDMI_PHY_DIGTXMODE_INVERT_DATA2)
//@}

/*! @name Register HDMI_PHY_DIGTXMODE, field DTB_SELECT[12:7] (RW)
 *
 * Debug Test Bus Select This field determines the pair of bits placed on the dtb[1:0] bus. These
 * selected pairs of bits come from the control register. The values that appear on dtb[1:0] are the
 * current values actually stored in the control register (not the override values) with the
 * exception of I 2 C values, which are not stored in the control register. For information about
 * the bit pairs, see dtb_select[6:0] .
 */
//@{
#define BP_HDMI_PHY_DIGTXMODE_DTB_SELECT      (7)      //!< Bit position for HDMI_PHY_DIGTXMODE_DTB_SELECT.
#define BM_HDMI_PHY_DIGTXMODE_DTB_SELECT      (0x00001f80)  //!< Bit mask for HDMI_PHY_DIGTXMODE_DTB_SELECT.

//! @brief Get value of HDMI_PHY_DIGTXMODE_DTB_SELECT from a register value.
#define BG_HDMI_PHY_DIGTXMODE_DTB_SELECT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_DIGTXMODE_DTB_SELECT) >> BP_HDMI_PHY_DIGTXMODE_DTB_SELECT)

//! @brief Format value for bitfield HDMI_PHY_DIGTXMODE_DTB_SELECT.
#define BF_HDMI_PHY_DIGTXMODE_DTB_SELECT(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_DIGTXMODE_DTB_SELECT) & BM_HDMI_PHY_DIGTXMODE_DTB_SELECT)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_STR_STATUS - Scope, Transmission Clock Alignment, and Resistance Calibration Set-on-Done Status
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_STR_STATUS - Scope, Transmission Clock Alignment, and Resistance Calibration Set-on-Done Status (RW)
 *
 * Reset value: 0x0000
 *
 * Register name : - Access type : Read/write/asynchronous set-on-done Address : 0x1F Value at reset
 * : 0x0000
 */
typedef union _hw_hdmi_phy_str_status
{
    reg16_t U;
    struct _hw_hdmi_phy_str_status_bitfields
    {
        unsigned short SCOPE_DONE0 : 1; //!< [0] Scope Done 0
        unsigned short SCOPE_DONE1 : 1; //!< [1] Scope Done 1
        unsigned short SCOPE_DONE2 : 1; //!< [2] Scope Done 2
        unsigned short CK_SCOPE_DONE : 1; //!< [3] Clock Scope Done
        unsigned short TX_CK_ALIGN_DONE : 1; //!< [4] Transmission Clock Alignment Done
        unsigned short RCAL_ADC_DONE : 1; //!< [5] Resistance Calibration Analog-to-Digital Converter Done
        unsigned short RESERVED0 : 10; //!< [15:6] Reserved
    } B;
} hw_hdmi_phy_str_status_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_STR_STATUS register
 */
//@{
#define HW_HDMI_PHY_STR_STATUS_ADDR      (REGS_HDMI_PHY_BASE + 0x1f)
//@}

/*
 * constants & macros for individual HDMI_PHY_STR_STATUS bitfields
 */

/*! @name Register HDMI_PHY_STR_STATUS, field SCOPE_DONE0[0] (RW)
 *
 * Scope Done 0 This bit indicates the status of tracing of 1's on channel 0.
 *
 * Values:
 * - 0 - The tracing process on channel 0 is not complete.
 * - 1 - The tracing process on channel 0 is complete.
 */
//@{
#define BP_HDMI_PHY_STR_STATUS_SCOPE_DONE0      (0)      //!< Bit position for HDMI_PHY_STR_STATUS_SCOPE_DONE0.
#define BM_HDMI_PHY_STR_STATUS_SCOPE_DONE0      (0x00000001)  //!< Bit mask for HDMI_PHY_STR_STATUS_SCOPE_DONE0.

//! @brief Get value of HDMI_PHY_STR_STATUS_SCOPE_DONE0 from a register value.
#define BG_HDMI_PHY_STR_STATUS_SCOPE_DONE0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_STR_STATUS_SCOPE_DONE0) >> BP_HDMI_PHY_STR_STATUS_SCOPE_DONE0)

//! @brief Format value for bitfield HDMI_PHY_STR_STATUS_SCOPE_DONE0.
#define BF_HDMI_PHY_STR_STATUS_SCOPE_DONE0(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_STR_STATUS_SCOPE_DONE0) & BM_HDMI_PHY_STR_STATUS_SCOPE_DONE0)
//@}

/*! @name Register HDMI_PHY_STR_STATUS, field SCOPE_DONE1[1] (RW)
 *
 * Scope Done 1 This bit indicates the status of tracing of 1's on channel 1.
 *
 * Values:
 * - 0 - The tracing process on channel 1 is not complete.
 * - 1 - The tracing process on channel 1 is complete.
 */
//@{
#define BP_HDMI_PHY_STR_STATUS_SCOPE_DONE1      (1)      //!< Bit position for HDMI_PHY_STR_STATUS_SCOPE_DONE1.
#define BM_HDMI_PHY_STR_STATUS_SCOPE_DONE1      (0x00000002)  //!< Bit mask for HDMI_PHY_STR_STATUS_SCOPE_DONE1.

//! @brief Get value of HDMI_PHY_STR_STATUS_SCOPE_DONE1 from a register value.
#define BG_HDMI_PHY_STR_STATUS_SCOPE_DONE1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_STR_STATUS_SCOPE_DONE1) >> BP_HDMI_PHY_STR_STATUS_SCOPE_DONE1)

//! @brief Format value for bitfield HDMI_PHY_STR_STATUS_SCOPE_DONE1.
#define BF_HDMI_PHY_STR_STATUS_SCOPE_DONE1(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_STR_STATUS_SCOPE_DONE1) & BM_HDMI_PHY_STR_STATUS_SCOPE_DONE1)
//@}

/*! @name Register HDMI_PHY_STR_STATUS, field SCOPE_DONE2[2] (RW)
 *
 * Scope Done 2 This bit indicates the status of tracing of 1's on channel 2.
 *
 * Values:
 * - 0 - The tracing process on channel 2 is not complete.
 * - 1 - The tracing process on channel 2 is complete.
 */
//@{
#define BP_HDMI_PHY_STR_STATUS_SCOPE_DONE2      (2)      //!< Bit position for HDMI_PHY_STR_STATUS_SCOPE_DONE2.
#define BM_HDMI_PHY_STR_STATUS_SCOPE_DONE2      (0x00000004)  //!< Bit mask for HDMI_PHY_STR_STATUS_SCOPE_DONE2.

//! @brief Get value of HDMI_PHY_STR_STATUS_SCOPE_DONE2 from a register value.
#define BG_HDMI_PHY_STR_STATUS_SCOPE_DONE2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_STR_STATUS_SCOPE_DONE2) >> BP_HDMI_PHY_STR_STATUS_SCOPE_DONE2)

//! @brief Format value for bitfield HDMI_PHY_STR_STATUS_SCOPE_DONE2.
#define BF_HDMI_PHY_STR_STATUS_SCOPE_DONE2(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_STR_STATUS_SCOPE_DONE2) & BM_HDMI_PHY_STR_STATUS_SCOPE_DONE2)
//@}

/*! @name Register HDMI_PHY_STR_STATUS, field CK_SCOPE_DONE[3] (RW)
 *
 * Clock Scope Done This bit indicates the status of tracing of 1's on the clock channel.
 *
 * Values:
 * - 0 - The tracing process on the clock channel is not complete.
 * - 1 - The tracing process on the clock channel is complete.
 */
//@{
#define BP_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE      (3)      //!< Bit position for HDMI_PHY_STR_STATUS_CK_SCOPE_DONE.
#define BM_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE      (0x00000008)  //!< Bit mask for HDMI_PHY_STR_STATUS_CK_SCOPE_DONE.

//! @brief Get value of HDMI_PHY_STR_STATUS_CK_SCOPE_DONE from a register value.
#define BG_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE) >> BP_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE)

//! @brief Format value for bitfield HDMI_PHY_STR_STATUS_CK_SCOPE_DONE.
#define BF_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE) & BM_HDMI_PHY_STR_STATUS_CK_SCOPE_DONE)
//@}

/*! @name Register HDMI_PHY_STR_STATUS, field TX_CK_ALIGN_DONE[4] (RW)
 *
 * Transmission Clock Alignment Done This bit indicates the status of completing the transmission
 * clock alignment FSM.
 *
 * Values:
 * - 0 - The transmission clock alignment FSM is not complete.
 * - 1 - The transmission clock alignment FSM is complete.
 */
//@{
#define BP_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE      (4)      //!< Bit position for HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE.
#define BM_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE      (0x00000010)  //!< Bit mask for HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE.

//! @brief Get value of HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE from a register value.
#define BG_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE) >> BP_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE)

//! @brief Format value for bitfield HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE.
#define BF_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE) & BM_HDMI_PHY_STR_STATUS_TX_CK_ALIGN_DONE)
//@}

/*! @name Register HDMI_PHY_STR_STATUS, field RCAL_ADC_DONE[5] (RW)
 *
 * Resistance Calibration Analog-to-Digital Converter Done This bit indicates the status of
 * completing the resistance calibration FSM.
 *
 * Values:
 * - 0 - The resistance calibration FSM is not complete.
 * - 1 - The resistance calibration FSM is complete.
 */
//@{
#define BP_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE      (5)      //!< Bit position for HDMI_PHY_STR_STATUS_RCAL_ADC_DONE.
#define BM_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE      (0x00000020)  //!< Bit mask for HDMI_PHY_STR_STATUS_RCAL_ADC_DONE.

//! @brief Get value of HDMI_PHY_STR_STATUS_RCAL_ADC_DONE from a register value.
#define BG_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE) >> BP_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE)

//! @brief Format value for bitfield HDMI_PHY_STR_STATUS_RCAL_ADC_DONE.
#define BF_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE(v)   ((__REG_VALUE_TYPE((v), reg16_t) << BP_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE) & BM_HDMI_PHY_STR_STATUS_RCAL_ADC_DONE)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPECNT0 - Scope Counter on Channel 0
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPECNT0 - Scope Counter on Channel 0 (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPECNT0 Access type : Read-only Address : 0x20 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopecnt0
{
    reg16_t U;
    struct _hw_hdmi_phy_scopecnt0_bitfields
    {
        unsigned short SCOPE_ONES_CNT0 : 16; //!< [15:0] Scope 1's Counter 0
    } B;
} hw_hdmi_phy_scopecnt0_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPECNT0 register
 */
//@{
#define HW_HDMI_PHY_SCOPECNT0_ADDR      (REGS_HDMI_PHY_BASE + 0x20)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPECNT0 bitfields
 */

/*! @name Register HDMI_PHY_SCOPECNT0, field SCOPE_ONES_CNT0[15:0] (RO)
 *
 * Scope 1's Counter 0 This register carries the number of counted 1's on channel 0. If the LFSR15
 * was used to generate the scope patterns, you must read the MSB bits under 0x25 register.
 */
//@{
#define BP_HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0      (0)      //!< Bit position for HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0.
#define BM_HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0      (0x0000ffff)  //!< Bit mask for HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0.

//! @brief Get value of HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0 from a register value.
#define BG_HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0) >> BP_HDMI_PHY_SCOPECNT0_SCOPE_ONES_CNT0)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPECNT1 - Scope Counter on Channel 1
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPECNT1 - Scope Counter on Channel 1 (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPECNT1 Access type : Read-only Address : 0x21 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopecnt1
{
    reg16_t U;
    struct _hw_hdmi_phy_scopecnt1_bitfields
    {
        unsigned short SCOPE_ONES_CNT1 : 16; //!< [15:0] Scope 1's Counter 1
    } B;
} hw_hdmi_phy_scopecnt1_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPECNT1 register
 */
//@{
#define HW_HDMI_PHY_SCOPECNT1_ADDR      (REGS_HDMI_PHY_BASE + 0x21)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPECNT1 bitfields
 */

/*! @name Register HDMI_PHY_SCOPECNT1, field SCOPE_ONES_CNT1[15:0] (RO)
 *
 * Scope 1's Counter 1 This register carries the number of counted 1's on channel 1. If the LFSR15
 * was used to generate the scope patterns, you must read the MSB bits under 0x25 register.
 */
//@{
#define BP_HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1      (0)      //!< Bit position for HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1.
#define BM_HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1      (0x0000ffff)  //!< Bit mask for HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1.

//! @brief Get value of HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1 from a register value.
#define BG_HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1) >> BP_HDMI_PHY_SCOPECNT1_SCOPE_ONES_CNT1)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPECNT2 - Scope Counter on Channel 2
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPECNT2 - Scope Counter on Channel 2 (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPECNT2 Access type : Read-only Address : 0x22 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopecnt2
{
    reg16_t U;
    struct _hw_hdmi_phy_scopecnt2_bitfields
    {
        unsigned short SCOPE_ONES_CNT2 : 16; //!< [15:0] Scope 1's Counter 2
    } B;
} hw_hdmi_phy_scopecnt2_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPECNT2 register
 */
//@{
#define HW_HDMI_PHY_SCOPECNT2_ADDR      (REGS_HDMI_PHY_BASE + 0x22)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPECNT2 bitfields
 */

/*! @name Register HDMI_PHY_SCOPECNT2, field SCOPE_ONES_CNT2[15:0] (RO)
 *
 * Scope 1's Counter 2 This register carries the number of counted 1's on channel 2. If the LFSR15
 * was used to generate the scope patterns, you must read the MSB bits under 0x26 register.
 */
//@{
#define BP_HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2      (0)      //!< Bit position for HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2.
#define BM_HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2      (0x0000ffff)  //!< Bit mask for HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2.

//! @brief Get value of HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2 from a register value.
#define BG_HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2) >> BP_HDMI_PHY_SCOPECNT2_SCOPE_ONES_CNT2)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPECNTCLK - Scope Counter on Clock Channel
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPECNTCLK - Scope Counter on Clock Channel (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPECNTCK Access type : Read-only Address : 0x23 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopecntclk
{
    reg16_t U;
    struct _hw_hdmi_phy_scopecntclk_bitfields
    {
        unsigned short CK_SCOPE_ONES_CNT : 16; //!< [15:0] Clock Scope 1's Counter
    } B;
} hw_hdmi_phy_scopecntclk_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPECNTCLK register
 */
//@{
#define HW_HDMI_PHY_SCOPECNTCLK_ADDR      (REGS_HDMI_PHY_BASE + 0x23)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPECNTCLK bitfields
 */

/*! @name Register HDMI_PHY_SCOPECNTCLK, field CK_SCOPE_ONES_CNT[15:0] (RO)
 *
 * Clock Scope 1's Counter This register carries the number of counted 1's on the clock channel. If
 * the LFSR15 was used to generate the scope patterns, you must read the MSB bits under 0x26
 * register.
 */
//@{
#define BP_HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT      (0)      //!< Bit position for HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT.
#define BM_HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT      (0x0000ffff)  //!< Bit mask for HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT.

//! @brief Get value of HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT from a register value.
#define BG_HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT) >> BP_HDMI_PHY_SCOPECNTCLK_CK_SCOPE_ONES_CNT)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPESAMPLE - Scope Sample Count MSB, Scope Sample Repetition
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPESAMPLE - Scope Sample Count MSB, Scope Sample Repetition (RW)
 *
 * Reset value: 0x13c0
 *
 * Register name : SCOPESAMPLE Access type : Read/write Address : 0x24 Value at reset : 0x13c0
 */
typedef union _hw_hdmi_phy_scopesample
{
    reg16_t U;
    struct _hw_hdmi_phy_scopesample_bitfields
    {
        unsigned short SCOPE_SAMPLE_CNT : 6; //!< [5:0] Scope Sample Counter
        unsigned short SCOPE_SAMPLE_REP : 7; //!< [12:6] Scope Sample Repetition
        unsigned short RESERVED0 : 3; //!< [15:13] Reserved
    } B;
} hw_hdmi_phy_scopesample_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPESAMPLE register
 */
//@{
#define HW_HDMI_PHY_SCOPESAMPLE_ADDR      (REGS_HDMI_PHY_BASE + 0x24)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPESAMPLE bitfields
 */

/*! @name Register HDMI_PHY_SCOPESAMPLE, field SCOPE_SAMPLE_CNT[5:0] (RO)
 *
 * Scope Sample Counter Indicates the number of samples that will be counted (should be multiple of
 * the LFSR length). These samples are the MSB bits only.
 */
//@{
#define BP_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT      (0)      //!< Bit position for HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT.
#define BM_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT      (0x0000003f)  //!< Bit mask for HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT.

//! @brief Get value of HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT from a register value.
#define BG_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT) >> BP_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_CNT)
//@}

/*! @name Register HDMI_PHY_SCOPESAMPLE, field SCOPE_SAMPLE_REP[12:6] (RO)
 *
 * Scope Sample Repetition Number of repetitions made by the scope FSM. The total samples captured
 * is scope_sample_rep x scope_sample_cnt.
 */
//@{
#define BP_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP      (6)      //!< Bit position for HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP.
#define BM_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP      (0x00001fc0)  //!< Bit mask for HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP.

//! @brief Get value of HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP from a register value.
#define BG_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP) >> BP_HDMI_PHY_SCOPESAMPLE_SCOPE_SAMPLE_REP)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPECNTMSB01 - Scope Counter MSB Channel 0 and Channel 1
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPECNTMSB01 - Scope Counter MSB Channel 0 and Channel 1 (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPECNTMSB01 Access type : Read-only Address : 0x25 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopecntmsb01
{
    reg16_t U;
    struct _hw_hdmi_phy_scopecntmsb01_bitfields
    {
        unsigned short SCOPE_ONES_CNT0 : 8; //!< [7:0] Scope 1's Counter 0
        unsigned short SCOPE_ONES_CNT1 : 5; //!< [12:8] Scope 1's Counter 1
        unsigned short RESERVED0 : 3; //!< [15:13] Reserved
    } B;
} hw_hdmi_phy_scopecntmsb01_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPECNTMSB01 register
 */
//@{
#define HW_HDMI_PHY_SCOPECNTMSB01_ADDR      (REGS_HDMI_PHY_BASE + 0x25)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPECNTMSB01 bitfields
 */

/*! @name Register HDMI_PHY_SCOPECNTMSB01, field SCOPE_ONES_CNT0[7:0] (RO)
 *
 * Scope 1's Counter 0 This register carries the number of counted 1's on channel 0. These 1's are
 * the MSB bits only.
 */
//@{
#define BP_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0      (0)      //!< Bit position for HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0.
#define BM_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0      (0x000000ff)  //!< Bit mask for HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0.

//! @brief Get value of HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0 from a register value.
#define BG_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0) >> BP_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT0)
//@}

/*! @name Register HDMI_PHY_SCOPECNTMSB01, field SCOPE_ONES_CNT1[12:8] (RO)
 *
 * Scope 1's Counter 1 This register carries the number of counted 1's on channel 1. These 1's are
 * the MSB bits only.
 */
//@{
#define BP_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1      (8)      //!< Bit position for HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1.
#define BM_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1      (0x00001f00)  //!< Bit mask for HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1.

//! @brief Get value of HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1 from a register value.
#define BG_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1) >> BP_HDMI_PHY_SCOPECNTMSB01_SCOPE_ONES_CNT1)
//@}

//-------------------------------------------------------------------------------------------
// HW_HDMI_PHY_SCOPECNTMSB2CK - Scope Counter MSB Channel 2 and Clock Channel
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_HDMI_PHY_SCOPECNTMSB2CK - Scope Counter MSB Channel 2 and Clock Channel (RO)
 *
 * Reset value: 0x0000
 *
 * Register name : SCOPECNTMSB2CK Access type : Read-only Address : 0x26 Value at reset : 0x0000
 */
typedef union _hw_hdmi_phy_scopecntmsb2ck
{
    reg16_t U;
    struct _hw_hdmi_phy_scopecntmsb2ck_bitfields
    {
        unsigned short SCOPE_ONES_CNT2 : 6; //!< [5:0] Scope 1's Counter 2
        unsigned short CK_SCOPE_ONES_CNT : 7; //!< [12:6] Clock Scope 1's Counter
        unsigned short RESERVED0 : 3; //!< [15:13] Reserved
    } B;
} hw_hdmi_phy_scopecntmsb2ck_t;
#endif

/*!
 * @name Constants and macros for entire HDMI_PHY_SCOPECNTMSB2CK register
 */
//@{
#define HW_HDMI_PHY_SCOPECNTMSB2CK_ADDR      (REGS_HDMI_PHY_BASE + 0x26)
//@}

/*
 * constants & macros for individual HDMI_PHY_SCOPECNTMSB2CK bitfields
 */

/*! @name Register HDMI_PHY_SCOPECNTMSB2CK, field SCOPE_ONES_CNT2[5:0] (RO)
 *
 * Scope 1's Counter 2 This register carries the number of counted 1's on channel 2. These 1's are
 * the MSB bits only.
 */
//@{
#define BP_HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2      (0)      //!< Bit position for HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2.
#define BM_HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2      (0x0000003f)  //!< Bit mask for HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2.

//! @brief Get value of HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2 from a register value.
#define BG_HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2) >> BP_HDMI_PHY_SCOPECNTMSB2CK_SCOPE_ONES_CNT2)
//@}

/*! @name Register HDMI_PHY_SCOPECNTMSB2CK, field CK_SCOPE_ONES_CNT[12:6] (RO)
 *
 * Clock Scope 1's Counter This register carries the number of counted 1's on the clock channel.
 * These 1's are the MSB bits only.
 */
//@{
#define BP_HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT      (6)      //!< Bit position for HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT.
#define BM_HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT      (0x00001fc0)  //!< Bit mask for HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT.

//! @brief Get value of HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT from a register value.
#define BG_HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT(r)   ((__REG_VALUE_TYPE((r), reg16_t) & BM_HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT) >> BP_HDMI_PHY_SCOPECNTMSB2CK_CK_SCOPE_ONES_CNT)
//@}

#endif // __HW_HDMI_PHY_REGISTERS_H__
// v18/121106/1.2.2
// EOF