xiuos/Ubiquitous/XiZi_AIoT/services/boards/imx6q-sabrelite/include/registers/regsesai.h

/*
 * Copyright (c) 2012, Freescale Semiconductor, Inc.
 * All rights reserved.
 *
 * THIS SOFTWARE IS PROVIDED BY FREESCALE "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
 * SHALL FREESCALE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
 * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
 * OF SUCH DAMAGE.
 */
/*
 * WARNING! DO NOT EDIT THIS FILE DIRECTLY!
 *
 * This file was generated automatically and any changes may be lost.
 */
#ifndef __HW_ESAI_REGISTERS_H__
#define __HW_ESAI_REGISTERS_H__

#include "regs.h"

/*
 * i.MX6DQ ESAI
 *
 * Enhanced Serial Audio Interface
 *
 * Registers defined in this header file:
 * - HW_ESAI_ETDR - ESAI Transmit Data Register
 * - HW_ESAI_ERDR - ESAI Receive Data Register
 * - HW_ESAI_ECR - ESAI Control Register
 * - HW_ESAI_ESR - ESAI Status Register
 * - HW_ESAI_TFCR - Transmit FIFO Configuration Register
 * - HW_ESAI_TFSR - Transmit FIFO Status Register
 * - HW_ESAI_RFCR - Receive FIFO Configuration Register
 * - HW_ESAI_RFSR - Receive FIFO Status Register
 * - HW_ESAI_TXn - Transmit Data Register n
 * - HW_ESAI_TSR - ESAI Transmit Slot Register
 * - HW_ESAI_RXn - Receive Data Register n
 * - HW_ESAI_SAISR - Serial Audio Interface Status Register
 * - HW_ESAI_SAICR - Serial Audio Interface Control Register
 * - HW_ESAI_TCR - Transmit Control Register
 * - HW_ESAI_TCCR - Transmit Clock Control Register
 * - HW_ESAI_RCR - Receive Control Register
 * - HW_ESAI_RCCR - Receive Clock Control Register
 * - HW_ESAI_TSMA - Transmit Slot Mask Register A
 * - HW_ESAI_TSMB - Transmit Slot Mask Register B
 * - HW_ESAI_RSMA - Receive Slot Mask Register A
 * - HW_ESAI_RSMB - Receive Slot Mask Register B
 * - HW_ESAI_PRRC - Port C Direction Register
 * - HW_ESAI_PCRC - Port C Control Register
 *
 * - hw_esai_t - Struct containing all module registers.
 */

//! @name Module base addresses
//@{
#ifndef REGS_ESAI_BASE
#define HW_ESAI_INSTANCE_COUNT (1) //!< Number of instances of the ESAI module.
#define REGS_ESAI_BASE (0x02024000) //!< Base address for ESAI.
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_ETDR - ESAI Transmit Data Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_ETDR - ESAI Transmit Data Register (WORZ)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_etdr
{
    reg32_t U;
    struct _hw_esai_etdr_bitfields
    {
        unsigned ETDR : 32; //!< [31:0] ESAI Transmit Data Register.
    } B;
} hw_esai_etdr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_ETDR register
 */
//@{
#define HW_ESAI_ETDR_ADDR      (REGS_ESAI_BASE + 0x0)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_ETDR           (*(volatile hw_esai_etdr_t *) HW_ESAI_ETDR_ADDR)
#define HW_ESAI_ETDR_WR(v)     (HW_ESAI_ETDR.U = (v))
#endif
//@}

/*
 * constants & macros for individual ESAI_ETDR bitfields
 */

/*! @name Register ESAI_ETDR, field ETDR[31:0] (WORZ)
 *
 * ESAI Transmit Data Register. Writing to this register stores the data written into the ESAI
 * Transmit FIFO. Writing to this register when the Transmit FIFO is full causes the data written to
 * be lost (the existing data within the FIFO is not overwritten). When multiple ESAI transmitters
 * are enabled, the data for each transmitter must be interleaved from lowest transmitter to highest
 * transmitter (for example, if transmitters 0, 2 and 3 are enabled then data must be written as
 * follows: transmitter #0, transmitter #2, transmitter #3, transmitter #0, transmitter #2,
 * transmitter #3, transmitter #0, etc). Data within the ESAI Transmit FIFO is passed to the ESAI
 * transmit shifter registers as defined by the Transmit Word Alignment configuration bits.
 */
//@{
#define BP_ESAI_ETDR_ETDR      (0)      //!< Bit position for ESAI_ETDR_ETDR.
#define BM_ESAI_ETDR_ETDR      (0xffffffff)  //!< Bit mask for ESAI_ETDR_ETDR.

//! @brief Get value of ESAI_ETDR_ETDR from a register value.
#define BG_ESAI_ETDR_ETDR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ETDR_ETDR) >> BP_ESAI_ETDR_ETDR)

//! @brief Format value for bitfield ESAI_ETDR_ETDR.
#define BF_ESAI_ETDR_ETDR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ETDR_ETDR) & BM_ESAI_ETDR_ETDR)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_ERDR - ESAI Receive Data Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_ERDR - ESAI Receive Data Register (RO)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_erdr
{
    reg32_t U;
    struct _hw_esai_erdr_bitfields
    {
        unsigned ERDR : 32; //!< [31:0] ESAI Receive Data Register.
    } B;
} hw_esai_erdr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_ERDR register
 */
//@{
#define HW_ESAI_ERDR_ADDR      (REGS_ESAI_BASE + 0x4)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_ERDR           (*(volatile hw_esai_erdr_t *) HW_ESAI_ERDR_ADDR)
#define HW_ESAI_ERDR_RD()      (HW_ESAI_ERDR.U)
#endif
//@}

/*
 * constants & macros for individual ESAI_ERDR bitfields
 */

/*! @name Register ESAI_ERDR, field ERDR[31:0] (RO)
 *
 * ESAI Receive Data Register. Reading this register returns the data within the ESAI Receive FIFO.
 * Reading this register when the Receive FIFO is empty returns the last valid data word. When
 * multiple ESAI receivers are enabled, the data for each receiver is interleaved from lowest
 * receiver to highest receiver (for example, if receivers 0, 2 and 3 are enabled then data is
 * returned as follows: receiver #0, receiver #2, receiver #3, receiver #0, receiver #2, receiver
 * #3, receiver #0, etc). Data is passed from the ESAI receive shift registers to the ESAI Receive
 * FIFO as defined by the Receiver Word Alignment configuration bits either zero or sign-extended
 * based on the Receive Extension control bit.
 */
//@{
#define BP_ESAI_ERDR_ERDR      (0)      //!< Bit position for ESAI_ERDR_ERDR.
#define BM_ESAI_ERDR_ERDR      (0xffffffff)  //!< Bit mask for ESAI_ERDR_ERDR.

//! @brief Get value of ESAI_ERDR_ERDR from a register value.
#define BG_ESAI_ERDR_ERDR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ERDR_ERDR) >> BP_ESAI_ERDR_ERDR)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_ECR - ESAI Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_ECR - ESAI Control Register (RW)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_ecr
{
    reg32_t U;
    struct _hw_esai_ecr_bitfields
    {
        unsigned ESAIEN : 1; //!< [0] ESAI Enable.
        unsigned ERST : 1; //!< [1] ESAI Reset.
        unsigned RESERVED0 : 14; //!< [15:2] Reserved
        unsigned ERO : 1; //!< [16] EXTAL Receiver Out.
        unsigned ERI : 1; //!< [17] EXTAL Receiver In.
        unsigned ETO : 1; //!< [18] EXTAL Transmitter Out.
        unsigned ETI : 1; //!< [19] EXTAL Transmitter In.
        unsigned RESERVED1 : 12; //!< [31:20] Reserved
    } B;
} hw_esai_ecr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_ECR register
 */
//@{
#define HW_ESAI_ECR_ADDR      (REGS_ESAI_BASE + 0x8)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_ECR           (*(volatile hw_esai_ecr_t *) HW_ESAI_ECR_ADDR)
#define HW_ESAI_ECR_RD()      (HW_ESAI_ECR.U)
#define HW_ESAI_ECR_WR(v)     (HW_ESAI_ECR.U = (v))
#define HW_ESAI_ECR_SET(v)    (HW_ESAI_ECR_WR(HW_ESAI_ECR_RD() |  (v)))
#define HW_ESAI_ECR_CLR(v)    (HW_ESAI_ECR_WR(HW_ESAI_ECR_RD() & ~(v)))
#define HW_ESAI_ECR_TOG(v)    (HW_ESAI_ECR_WR(HW_ESAI_ECR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_ECR bitfields
 */

/*! @name Register ESAI_ECR, field ESAIEN[0] (RW)
 *
 * ESAI Enable. Enables/disables the ESAI logic clock. Enable the ESAI before reading or writing
 * other ESAI registers.
 *
 * Values:
 * - 0 - ESAI disabled.
 * - 1 - ESAI enabled.
 */
//@{
#define BP_ESAI_ECR_ESAIEN      (0)      //!< Bit position for ESAI_ECR_ESAIEN.
#define BM_ESAI_ECR_ESAIEN      (0x00000001)  //!< Bit mask for ESAI_ECR_ESAIEN.

//! @brief Get value of ESAI_ECR_ESAIEN from a register value.
#define BG_ESAI_ECR_ESAIEN(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ECR_ESAIEN) >> BP_ESAI_ECR_ESAIEN)

//! @brief Format value for bitfield ESAI_ECR_ESAIEN.
#define BF_ESAI_ECR_ESAIEN(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ECR_ESAIEN) & BM_ESAI_ECR_ESAIEN)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ESAIEN field to a new value.
#define BW_ESAI_ECR_ESAIEN(v)   (HW_ESAI_ECR_WR((HW_ESAI_ECR_RD() & ~BM_ESAI_ECR_ESAIEN) | BF_ESAI_ECR_ESAIEN(v)))
#endif
//@}

/*! @name Register ESAI_ECR, field ERST[1] (RW)
 *
 * ESAI Reset. Reset the ESAI core logic (including configuration registers) but not the ESAI FIFOs.
 *
 * Values:
 * - 0 - ESAI not reset.
 * - 1 - ESAI reset.
 */
//@{
#define BP_ESAI_ECR_ERST      (1)      //!< Bit position for ESAI_ECR_ERST.
#define BM_ESAI_ECR_ERST      (0x00000002)  //!< Bit mask for ESAI_ECR_ERST.

//! @brief Get value of ESAI_ECR_ERST from a register value.
#define BG_ESAI_ECR_ERST(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ECR_ERST) >> BP_ESAI_ECR_ERST)

//! @brief Format value for bitfield ESAI_ECR_ERST.
#define BF_ESAI_ECR_ERST(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ECR_ERST) & BM_ESAI_ECR_ERST)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ERST field to a new value.
#define BW_ESAI_ECR_ERST(v)   (HW_ESAI_ECR_WR((HW_ESAI_ECR_RD() & ~BM_ESAI_ECR_ERST) | BF_ESAI_ECR_ERST(v)))
#endif
//@}

/*! @name Register ESAI_ECR, field ERO[16] (RW)
 *
 * EXTAL Receiver Out. Drive the EXTAL input on the High Frequency Receiver Clock pin.
 *
 * Values:
 * - 0 - HCKR pin has normal function.
 * - 1 - EXTAL driven onto HCKR pin.
 */
//@{
#define BP_ESAI_ECR_ERO      (16)      //!< Bit position for ESAI_ECR_ERO.
#define BM_ESAI_ECR_ERO      (0x00010000)  //!< Bit mask for ESAI_ECR_ERO.

//! @brief Get value of ESAI_ECR_ERO from a register value.
#define BG_ESAI_ECR_ERO(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ECR_ERO) >> BP_ESAI_ECR_ERO)

//! @brief Format value for bitfield ESAI_ECR_ERO.
#define BF_ESAI_ECR_ERO(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ECR_ERO) & BM_ESAI_ECR_ERO)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ERO field to a new value.
#define BW_ESAI_ECR_ERO(v)   (HW_ESAI_ECR_WR((HW_ESAI_ECR_RD() & ~BM_ESAI_ECR_ERO) | BF_ESAI_ECR_ERO(v)))
#endif
//@}

/*! @name Register ESAI_ECR, field ERI[17] (RW)
 *
 * EXTAL Receiver In. Mux EXTAL in place of the High Frequency Receiver Clock input pin. HCKR can
 * still be used to drive a divided down EXTAL or as GPIO.
 *
 * Values:
 * - 0 - HCKR pin has normal function.
 * - 1 - EXTAL muxed into HCKR input.
 */
//@{
#define BP_ESAI_ECR_ERI      (17)      //!< Bit position for ESAI_ECR_ERI.
#define BM_ESAI_ECR_ERI      (0x00020000)  //!< Bit mask for ESAI_ECR_ERI.

//! @brief Get value of ESAI_ECR_ERI from a register value.
#define BG_ESAI_ECR_ERI(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ECR_ERI) >> BP_ESAI_ECR_ERI)

//! @brief Format value for bitfield ESAI_ECR_ERI.
#define BF_ESAI_ECR_ERI(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ECR_ERI) & BM_ESAI_ECR_ERI)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ERI field to a new value.
#define BW_ESAI_ECR_ERI(v)   (HW_ESAI_ECR_WR((HW_ESAI_ECR_RD() & ~BM_ESAI_ECR_ERI) | BF_ESAI_ECR_ERI(v)))
#endif
//@}

/*! @name Register ESAI_ECR, field ETO[18] (RW)
 *
 * EXTAL Transmitter Out. Drive the EXTAL input on the High Frequency Transmitter Clock pin.
 *
 * Values:
 * - 0 - HCKT pin has normal function.
 * - 1 - EXTAL driven onto HCKT pin.
 */
//@{
#define BP_ESAI_ECR_ETO      (18)      //!< Bit position for ESAI_ECR_ETO.
#define BM_ESAI_ECR_ETO      (0x00040000)  //!< Bit mask for ESAI_ECR_ETO.

//! @brief Get value of ESAI_ECR_ETO from a register value.
#define BG_ESAI_ECR_ETO(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ECR_ETO) >> BP_ESAI_ECR_ETO)

//! @brief Format value for bitfield ESAI_ECR_ETO.
#define BF_ESAI_ECR_ETO(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ECR_ETO) & BM_ESAI_ECR_ETO)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ETO field to a new value.
#define BW_ESAI_ECR_ETO(v)   (HW_ESAI_ECR_WR((HW_ESAI_ECR_RD() & ~BM_ESAI_ECR_ETO) | BF_ESAI_ECR_ETO(v)))
#endif
//@}

/*! @name Register ESAI_ECR, field ETI[19] (RW)
 *
 * EXTAL Transmitter In. Mux EXTAL in place of the High Frequency Transmitter Clock input pin. HCKT
 * can still be used to drive a divided down EXTAL or as GPIO.
 *
 * Values:
 * - 0 - HCKT pin has normal function.
 * - 1 - EXTAL muxed into HCKT input.
 */
//@{
#define BP_ESAI_ECR_ETI      (19)      //!< Bit position for ESAI_ECR_ETI.
#define BM_ESAI_ECR_ETI      (0x00080000)  //!< Bit mask for ESAI_ECR_ETI.

//! @brief Get value of ESAI_ECR_ETI from a register value.
#define BG_ESAI_ECR_ETI(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ECR_ETI) >> BP_ESAI_ECR_ETI)

//! @brief Format value for bitfield ESAI_ECR_ETI.
#define BF_ESAI_ECR_ETI(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_ECR_ETI) & BM_ESAI_ECR_ETI)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ETI field to a new value.
#define BW_ESAI_ECR_ETI(v)   (HW_ESAI_ECR_WR((HW_ESAI_ECR_RD() & ~BM_ESAI_ECR_ETI) | BF_ESAI_ECR_ETI(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_ESR - ESAI Status Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_ESR - ESAI Status Register (RO)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_esr
{
    reg32_t U;
    struct _hw_esai_esr_bitfields
    {
        unsigned RD : 1; //!< [0] Receive Data.
        unsigned RED : 1; //!< [1] Receive Even Data.
        unsigned RDE : 1; //!< [2] Receive Data Exception.
        unsigned RLS : 1; //!< [3] Receive Last Slot.
        unsigned TD : 1; //!< [4] Transmit Data.
        unsigned TED : 1; //!< [5] Transmit Even Data.
        unsigned TDE : 1; //!< [6] Transmit Data Exception.
        unsigned TLS : 1; //!< [7] Transmit Last Slot.
        unsigned TFE : 1; //!< [8] Transmit FIFO Empty.
        unsigned RFF : 1; //!< [9] Receive FIFO Full.
        unsigned TINIT : 1; //!< [10] Transmit Initialization.
        unsigned RESERVED0 : 21; //!< [31:11] Reserved
    } B;
} hw_esai_esr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_ESR register
 */
//@{
#define HW_ESAI_ESR_ADDR      (REGS_ESAI_BASE + 0xc)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_ESR           (*(volatile hw_esai_esr_t *) HW_ESAI_ESR_ADDR)
#define HW_ESAI_ESR_RD()      (HW_ESAI_ESR.U)
#endif
//@}

/*
 * constants & macros for individual ESAI_ESR bitfields
 */

/*! @name Register ESAI_ESR, field RD[0] (RO)
 *
 * Receive Data.
 *
 * Values:
 * - 0 - RD is not the highest priority active interrupt.
 * - 1 - RD is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_RD      (0)      //!< Bit position for ESAI_ESR_RD.
#define BM_ESAI_ESR_RD      (0x00000001)  //!< Bit mask for ESAI_ESR_RD.

//! @brief Get value of ESAI_ESR_RD from a register value.
#define BG_ESAI_ESR_RD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_RD) >> BP_ESAI_ESR_RD)
//@}

/*! @name Register ESAI_ESR, field RED[1] (RO)
 *
 * Receive Even Data.
 *
 * Values:
 * - 0 - RED is not the highest priority active interrupt.
 * - 1 - RED is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_RED      (1)      //!< Bit position for ESAI_ESR_RED.
#define BM_ESAI_ESR_RED      (0x00000002)  //!< Bit mask for ESAI_ESR_RED.

//! @brief Get value of ESAI_ESR_RED from a register value.
#define BG_ESAI_ESR_RED(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_RED) >> BP_ESAI_ESR_RED)
//@}

/*! @name Register ESAI_ESR, field RDE[2] (RO)
 *
 * Receive Data Exception.
 *
 * Values:
 * - 0 - RDE is not the highest priority active interrupt.
 * - 1 - RDE is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_RDE      (2)      //!< Bit position for ESAI_ESR_RDE.
#define BM_ESAI_ESR_RDE      (0x00000004)  //!< Bit mask for ESAI_ESR_RDE.

//! @brief Get value of ESAI_ESR_RDE from a register value.
#define BG_ESAI_ESR_RDE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_RDE) >> BP_ESAI_ESR_RDE)
//@}

/*! @name Register ESAI_ESR, field RLS[3] (RO)
 *
 * Receive Last Slot. Reading this register when RLS is set will negate the Receive Last Slot
 * interrupt.
 *
 * Values:
 * - 0 - RLS is not the highest priority active interrupt.
 * - 1 - RLS is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_RLS      (3)      //!< Bit position for ESAI_ESR_RLS.
#define BM_ESAI_ESR_RLS      (0x00000008)  //!< Bit mask for ESAI_ESR_RLS.

//! @brief Get value of ESAI_ESR_RLS from a register value.
#define BG_ESAI_ESR_RLS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_RLS) >> BP_ESAI_ESR_RLS)
//@}

/*! @name Register ESAI_ESR, field TD[4] (RO)
 *
 * Transmit Data.
 *
 * Values:
 * - 0 - TD is not the highest priority active interrupt.
 * - 1 - TD is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_TD      (4)      //!< Bit position for ESAI_ESR_TD.
#define BM_ESAI_ESR_TD      (0x00000010)  //!< Bit mask for ESAI_ESR_TD.

//! @brief Get value of ESAI_ESR_TD from a register value.
#define BG_ESAI_ESR_TD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_TD) >> BP_ESAI_ESR_TD)
//@}

/*! @name Register ESAI_ESR, field TED[5] (RO)
 *
 * Transmit Even Data.
 *
 * Values:
 * - 0 - TED is not the highest priority active interrupt.
 * - 1 - TED is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_TED      (5)      //!< Bit position for ESAI_ESR_TED.
#define BM_ESAI_ESR_TED      (0x00000020)  //!< Bit mask for ESAI_ESR_TED.

//! @brief Get value of ESAI_ESR_TED from a register value.
#define BG_ESAI_ESR_TED(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_TED) >> BP_ESAI_ESR_TED)
//@}

/*! @name Register ESAI_ESR, field TDE[6] (RO)
 *
 * Transmit Data Exception.
 *
 * Values:
 * - 0 - TDE is not the highest priority active interrupt.
 * - 1 - TDE is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_TDE      (6)      //!< Bit position for ESAI_ESR_TDE.
#define BM_ESAI_ESR_TDE      (0x00000040)  //!< Bit mask for ESAI_ESR_TDE.

//! @brief Get value of ESAI_ESR_TDE from a register value.
#define BG_ESAI_ESR_TDE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_TDE) >> BP_ESAI_ESR_TDE)
//@}

/*! @name Register ESAI_ESR, field TLS[7] (RO)
 *
 * Transmit Last Slot. Reading this register when TLS is set will negate the Transmit Last Slot
 * interrupt.
 *
 * Values:
 * - 0 - TLS is not the highest priority active interrupt.
 * - 1 - TLS is the highest priority active interrupt.
 */
//@{
#define BP_ESAI_ESR_TLS      (7)      //!< Bit position for ESAI_ESR_TLS.
#define BM_ESAI_ESR_TLS      (0x00000080)  //!< Bit mask for ESAI_ESR_TLS.

//! @brief Get value of ESAI_ESR_TLS from a register value.
#define BG_ESAI_ESR_TLS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_TLS) >> BP_ESAI_ESR_TLS)
//@}

/*! @name Register ESAI_ESR, field TFE[8] (RO)
 *
 * Transmit FIFO Empty. Indicates that the number of empty slots in the Transmit FIFO has met or
 * exceeded the Transmit FIFO Watermark. This flag also drives the ESAI Transmitter DMA request
 * line. ESAI FIFO DMA request see .
 *
 * Values:
 * - 0 - Number of empty slots in Transmit FIFO less than Transmit FIFO watermark.
 * - 1 - Number of empty slots in Transmit FIFO is equal to or greater than Transmit FIFO watermark.
 */
//@{
#define BP_ESAI_ESR_TFE      (8)      //!< Bit position for ESAI_ESR_TFE.
#define BM_ESAI_ESR_TFE      (0x00000100)  //!< Bit mask for ESAI_ESR_TFE.

//! @brief Get value of ESAI_ESR_TFE from a register value.
#define BG_ESAI_ESR_TFE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_TFE) >> BP_ESAI_ESR_TFE)
//@}

/*! @name Register ESAI_ESR, field RFF[9] (RO)
 *
 * Receive FIFO Full. Indicates that the number of data words in the Receive FIFO has equaled or
 * exceeded the Receive FIFO Watermark. This flag also drives the ESAI Receiver DMA request line.
 * ESAI FIFO DMA requests see .
 *
 * Values:
 * - 0 - Number of words in Receive FIFO less than Receive FIFO watermark.
 * - 1 - Number of words in Receive FIFO is equal to or greater than Receive FIFO watermark.
 */
//@{
#define BP_ESAI_ESR_RFF      (9)      //!< Bit position for ESAI_ESR_RFF.
#define BM_ESAI_ESR_RFF      (0x00000200)  //!< Bit mask for ESAI_ESR_RFF.

//! @brief Get value of ESAI_ESR_RFF from a register value.
#define BG_ESAI_ESR_RFF(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_RFF) >> BP_ESAI_ESR_RFF)
//@}

/*! @name Register ESAI_ESR, field TINIT[10] (RO)
 *
 * Transmit Initialization. Indicates that the Transmit FIFO is writing the first word for each
 * enabled transmitter into the Transmit Data Registers. This bit sets when the Transmit FIFO is
 * enabled (provided Transmit Initialization is enabled) and clears after the Transmit Data
 * Registers have been initialized. The Transmit Enable bits in the Transmit Control Register should
 * not be set until this flag has cleared.
 *
 * Values:
 * - 0 - Transmitter has finished initializing the Transmit Data Registers (or Transmit FIFO is not enabled
 *     or Transmit Initialization is not enabled).
 * - 1 - Transmitter has not finished initializing the Transmit Data Registers.
 */
//@{
#define BP_ESAI_ESR_TINIT      (10)      //!< Bit position for ESAI_ESR_TINIT.
#define BM_ESAI_ESR_TINIT      (0x00000400)  //!< Bit mask for ESAI_ESR_TINIT.

//! @brief Get value of ESAI_ESR_TINIT from a register value.
#define BG_ESAI_ESR_TINIT(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_ESR_TINIT) >> BP_ESAI_ESR_TINIT)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TFCR - Transmit FIFO Configuration Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TFCR - Transmit FIFO Configuration Register (RW)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_tfcr
{
    reg32_t U;
    struct _hw_esai_tfcr_bitfields
    {
        unsigned TFE : 1; //!< [0] Transmit FIFO Enable.
        unsigned TFR : 1; //!< [1] Transmit FIFO Reset.
        unsigned TE0 : 1; //!< [2] Transmitter #0 FIFO Enable.
        unsigned TE1 : 1; //!< [3] Transmitter #1 FIFO Enable.
        unsigned TE2 : 1; //!< [4] Transmitter #2 FIFO Enable.
        unsigned TE3 : 1; //!< [5] Transmitter #3 FIFO Enable.
        unsigned TE4 : 1; //!< [6] Transmitter #4 FIFO Enable.
        unsigned TE5 : 1; //!< [7] Transmitter #5 FIFO Enable.
        unsigned TFWM : 8; //!< [15:8] Transmit FIFO Watermark.
        unsigned TWA : 3; //!< [18:16] Transmit Word Alignment.
        unsigned TIEN : 1; //!< [19] Transmitter Initialization Enable.
        unsigned RESERVED0 : 12; //!< [31:20] Reserved
    } B;
} hw_esai_tfcr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TFCR register
 */
//@{
#define HW_ESAI_TFCR_ADDR      (REGS_ESAI_BASE + 0x10)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TFCR           (*(volatile hw_esai_tfcr_t *) HW_ESAI_TFCR_ADDR)
#define HW_ESAI_TFCR_RD()      (HW_ESAI_TFCR.U)
#define HW_ESAI_TFCR_WR(v)     (HW_ESAI_TFCR.U = (v))
#define HW_ESAI_TFCR_SET(v)    (HW_ESAI_TFCR_WR(HW_ESAI_TFCR_RD() |  (v)))
#define HW_ESAI_TFCR_CLR(v)    (HW_ESAI_TFCR_WR(HW_ESAI_TFCR_RD() & ~(v)))
#define HW_ESAI_TFCR_TOG(v)    (HW_ESAI_TFCR_WR(HW_ESAI_TFCR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_TFCR bitfields
 */

/*! @name Register ESAI_TFCR, field TFE[0] (RW)
 *
 * Transmit FIFO Enable. This bit enables the use of the Transmit FIFO.
 *
 * Values:
 * - 0 - Transmit FIFO disabled.
 * - 1 - Transmit FIFO enabled.
 */
//@{
#define BP_ESAI_TFCR_TFE      (0)      //!< Bit position for ESAI_TFCR_TFE.
#define BM_ESAI_TFCR_TFE      (0x00000001)  //!< Bit mask for ESAI_TFCR_TFE.

//! @brief Get value of ESAI_TFCR_TFE from a register value.
#define BG_ESAI_TFCR_TFE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TFE) >> BP_ESAI_TFCR_TFE)

//! @brief Format value for bitfield ESAI_TFCR_TFE.
#define BF_ESAI_TFCR_TFE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TFE) & BM_ESAI_TFCR_TFE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFE field to a new value.
#define BW_ESAI_TFCR_TFE(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TFE) | BF_ESAI_TFCR_TFE(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TFR[1] (RW)
 *
 * Transmit FIFO Reset. This bit resets the Transmit FIFO pointers.
 *
 * Values:
 * - 0 - Transmit FIFO not reset.
 * - 1 - Transmit FIFO reset.
 */
//@{
#define BP_ESAI_TFCR_TFR      (1)      //!< Bit position for ESAI_TFCR_TFR.
#define BM_ESAI_TFCR_TFR      (0x00000002)  //!< Bit mask for ESAI_TFCR_TFR.

//! @brief Get value of ESAI_TFCR_TFR from a register value.
#define BG_ESAI_TFCR_TFR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TFR) >> BP_ESAI_TFCR_TFR)

//! @brief Format value for bitfield ESAI_TFCR_TFR.
#define BF_ESAI_TFCR_TFR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TFR) & BM_ESAI_TFCR_TFR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFR field to a new value.
#define BW_ESAI_TFCR_TFR(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TFR) | BF_ESAI_TFCR_TFR(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TE0[2] (RW)
 *
 * Transmitter #0 FIFO Enable. This bit enables transmitter #0 to use the Transmit FIFO. Do not
 * change this bit when the Transmitter FIFO is enabled.
 *
 * Values:
 * - 0 - Transmitter #0 is not using the Transmit FIFO.
 * - 1 - Transmitter #0 is using the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFCR_TE0      (2)      //!< Bit position for ESAI_TFCR_TE0.
#define BM_ESAI_TFCR_TE0      (0x00000004)  //!< Bit mask for ESAI_TFCR_TE0.

//! @brief Get value of ESAI_TFCR_TE0 from a register value.
#define BG_ESAI_TFCR_TE0(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TE0) >> BP_ESAI_TFCR_TE0)

//! @brief Format value for bitfield ESAI_TFCR_TE0.
#define BF_ESAI_TFCR_TE0(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TE0) & BM_ESAI_TFCR_TE0)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE0 field to a new value.
#define BW_ESAI_TFCR_TE0(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TE0) | BF_ESAI_TFCR_TE0(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TE1[3] (RW)
 *
 * Transmitter #1 FIFO Enable. This bit enables transmitter #1 to use the Transmit FIFO. Do not
 * change this bit when the Transmitter FIFO is enabled.
 *
 * Values:
 * - 0 - Transmitter #1 is not using the Transmit FIFO.
 * - 1 - Transmitter #1 is using the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFCR_TE1      (3)      //!< Bit position for ESAI_TFCR_TE1.
#define BM_ESAI_TFCR_TE1      (0x00000008)  //!< Bit mask for ESAI_TFCR_TE1.

//! @brief Get value of ESAI_TFCR_TE1 from a register value.
#define BG_ESAI_TFCR_TE1(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TE1) >> BP_ESAI_TFCR_TE1)

//! @brief Format value for bitfield ESAI_TFCR_TE1.
#define BF_ESAI_TFCR_TE1(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TE1) & BM_ESAI_TFCR_TE1)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE1 field to a new value.
#define BW_ESAI_TFCR_TE1(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TE1) | BF_ESAI_TFCR_TE1(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TE2[4] (RW)
 *
 * Transmitter #2 FIFO Enable. This bit enables transmitter #2 to use the Transmit FIFO. Do not
 * change this bit when the Transmitter FIFO is enabled.
 *
 * Values:
 * - 0 - Transmitter #2 is not using the Transmit FIFO.
 * - 1 - Transmitter #2 is using the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFCR_TE2      (4)      //!< Bit position for ESAI_TFCR_TE2.
#define BM_ESAI_TFCR_TE2      (0x00000010)  //!< Bit mask for ESAI_TFCR_TE2.

//! @brief Get value of ESAI_TFCR_TE2 from a register value.
#define BG_ESAI_TFCR_TE2(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TE2) >> BP_ESAI_TFCR_TE2)

//! @brief Format value for bitfield ESAI_TFCR_TE2.
#define BF_ESAI_TFCR_TE2(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TE2) & BM_ESAI_TFCR_TE2)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE2 field to a new value.
#define BW_ESAI_TFCR_TE2(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TE2) | BF_ESAI_TFCR_TE2(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TE3[5] (RW)
 *
 * Transmitter #3 FIFO Enable. This bit enables transmitter #3 to use the Transmit FIFO. Do not
 * change this bit when the Transmitter FIFO is enabled.
 *
 * Values:
 * - 0 - Transmitter #3 is not using the Transmit FIFO.
 * - 1 - Transmitter #3 is using the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFCR_TE3      (5)      //!< Bit position for ESAI_TFCR_TE3.
#define BM_ESAI_TFCR_TE3      (0x00000020)  //!< Bit mask for ESAI_TFCR_TE3.

//! @brief Get value of ESAI_TFCR_TE3 from a register value.
#define BG_ESAI_TFCR_TE3(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TE3) >> BP_ESAI_TFCR_TE3)

//! @brief Format value for bitfield ESAI_TFCR_TE3.
#define BF_ESAI_TFCR_TE3(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TE3) & BM_ESAI_TFCR_TE3)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE3 field to a new value.
#define BW_ESAI_TFCR_TE3(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TE3) | BF_ESAI_TFCR_TE3(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TE4[6] (RW)
 *
 * Transmitter #4 FIFO Enable. This bit enables transmitter #4 to use the Transmit FIFO. Do not
 * change this bit when the Transmitter FIFO is enabled.
 *
 * Values:
 * - 0 - Transmitter #4 is not using the Transmit FIFO.
 * - 1 - Transmitter #4 is using the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFCR_TE4      (6)      //!< Bit position for ESAI_TFCR_TE4.
#define BM_ESAI_TFCR_TE4      (0x00000040)  //!< Bit mask for ESAI_TFCR_TE4.

//! @brief Get value of ESAI_TFCR_TE4 from a register value.
#define BG_ESAI_TFCR_TE4(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TE4) >> BP_ESAI_TFCR_TE4)

//! @brief Format value for bitfield ESAI_TFCR_TE4.
#define BF_ESAI_TFCR_TE4(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TE4) & BM_ESAI_TFCR_TE4)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE4 field to a new value.
#define BW_ESAI_TFCR_TE4(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TE4) | BF_ESAI_TFCR_TE4(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TE5[7] (RW)
 *
 * Transmitter #5 FIFO Enable. This bit enables transmitter #5 to use the Transmit FIFO. Do not
 * change this bit when the Transmitter FIFO is enabled.
 *
 * Values:
 * - 0 - Transmitter #5 is not using the Transmit FIFO.
 * - 1 - Transmitter #5 is using the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFCR_TE5      (7)      //!< Bit position for ESAI_TFCR_TE5.
#define BM_ESAI_TFCR_TE5      (0x00000080)  //!< Bit mask for ESAI_TFCR_TE5.

//! @brief Get value of ESAI_TFCR_TE5 from a register value.
#define BG_ESAI_TFCR_TE5(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TE5) >> BP_ESAI_TFCR_TE5)

//! @brief Format value for bitfield ESAI_TFCR_TE5.
#define BF_ESAI_TFCR_TE5(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TE5) & BM_ESAI_TFCR_TE5)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE5 field to a new value.
#define BW_ESAI_TFCR_TE5(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TE5) | BF_ESAI_TFCR_TE5(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TFWM[15:8] (RW)
 *
 * Transmit FIFO Watermark. These bits configure the threshold at which the Transmit FIFO Empty flag
 * will set. The TFE is set when the number of empty slots in the Transmit FIFO equal or exceed the
 * selected threshold.
 */
//@{
#define BP_ESAI_TFCR_TFWM      (8)      //!< Bit position for ESAI_TFCR_TFWM.
#define BM_ESAI_TFCR_TFWM      (0x0000ff00)  //!< Bit mask for ESAI_TFCR_TFWM.

//! @brief Get value of ESAI_TFCR_TFWM from a register value.
#define BG_ESAI_TFCR_TFWM(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TFWM) >> BP_ESAI_TFCR_TFWM)

//! @brief Format value for bitfield ESAI_TFCR_TFWM.
#define BF_ESAI_TFCR_TFWM(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TFWM) & BM_ESAI_TFCR_TFWM)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFWM field to a new value.
#define BW_ESAI_TFCR_TFWM(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TFWM) | BF_ESAI_TFCR_TFWM(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TWA[18:16] (RW)
 *
 * Transmit Word Alignment. Configures the alignment of the data written into the ESAI Transmit Data
 * Register and then passed to the relevant 24 bit Transmit shift register.
 *
 * Values:
 * - 000 - MSB of data is bit 31. Data bits 7-0 are ignored when passed to transmit shift register.
 * - 001 - MSB of data is bit 27. Data bits 3-0 are ignored when passed to transmit shift register.
 * - 010 - MSB of data is bit 23.
 * - 011 - MSB of data is bit 19. Bottom 4 bits of transmit shift register are zeroed.
 * - 100 - MSB of data is bit 15. Bottom 8 bits of transmit shift register are zeroed.
 * - 101 - MSB of data is bit 11. Bottom 12 bits of transmit shift register are zeroed.
 * - 110 - MSB of data is bit 7. Bottom 16 bits of transmit shift register are zeroed.
 * - 111 - MSB of data is bit 3. Bottom 20 bits of transmit shift register are zeroed.
 */
//@{
#define BP_ESAI_TFCR_TWA      (16)      //!< Bit position for ESAI_TFCR_TWA.
#define BM_ESAI_TFCR_TWA      (0x00070000)  //!< Bit mask for ESAI_TFCR_TWA.

//! @brief Get value of ESAI_TFCR_TWA from a register value.
#define BG_ESAI_TFCR_TWA(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TWA) >> BP_ESAI_TFCR_TWA)

//! @brief Format value for bitfield ESAI_TFCR_TWA.
#define BF_ESAI_TFCR_TWA(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TWA) & BM_ESAI_TFCR_TWA)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TWA field to a new value.
#define BW_ESAI_TFCR_TWA(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TWA) | BF_ESAI_TFCR_TWA(v)))
#endif
//@}

/*! @name Register ESAI_TFCR, field TIEN[19] (RW)
 *
 * Transmitter Initialization Enable. Enables the initialization of the Transmit Data Registers when
 * the Transmitter FIFO is enabled. TIEN=1 is recommended.
 *
 * Values:
 * - 0 - Transmit Data Registers are not initialized from the FIFO once the Transmit FIFO is enabled.
 *     Software must manually initialize the Transmit Data Registers separately.
 * - 1 - Transmit Data Registers are initialized from the FIFO once the Transmit FIFO is enabled.
 */
//@{
#define BP_ESAI_TFCR_TIEN      (19)      //!< Bit position for ESAI_TFCR_TIEN.
#define BM_ESAI_TFCR_TIEN      (0x00080000)  //!< Bit mask for ESAI_TFCR_TIEN.

//! @brief Get value of ESAI_TFCR_TIEN from a register value.
#define BG_ESAI_TFCR_TIEN(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFCR_TIEN) >> BP_ESAI_TFCR_TIEN)

//! @brief Format value for bitfield ESAI_TFCR_TIEN.
#define BF_ESAI_TFCR_TIEN(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TFCR_TIEN) & BM_ESAI_TFCR_TIEN)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TIEN field to a new value.
#define BW_ESAI_TFCR_TIEN(v)   (HW_ESAI_TFCR_WR((HW_ESAI_TFCR_RD() & ~BM_ESAI_TFCR_TIEN) | BF_ESAI_TFCR_TIEN(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TFSR - Transmit FIFO Status Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TFSR - Transmit FIFO Status Register (RO)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_tfsr
{
    reg32_t U;
    struct _hw_esai_tfsr_bitfields
    {
        unsigned TFCNT : 8; //!< [7:0] Transmit FIFO Counter.
        unsigned NTFI : 3; //!< [10:8] Next Transmitter FIFO In.
        unsigned RESERVED0 : 1; //!< [11] Reserved
        unsigned NTFO : 3; //!< [14:12] Next Transmitter FIFO Out.
        unsigned RESERVED1 : 17; //!< [31:15] Reserved
    } B;
} hw_esai_tfsr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TFSR register
 */
//@{
#define HW_ESAI_TFSR_ADDR      (REGS_ESAI_BASE + 0x14)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TFSR           (*(volatile hw_esai_tfsr_t *) HW_ESAI_TFSR_ADDR)
#define HW_ESAI_TFSR_RD()      (HW_ESAI_TFSR.U)
#endif
//@}

/*
 * constants & macros for individual ESAI_TFSR bitfields
 */

/*! @name Register ESAI_TFSR, field TFCNT[7:0] (RO)
 *
 * Transmit FIFO Counter. These bits indicate the number of data words stored in the Transmit FIFO.
 */
//@{
#define BP_ESAI_TFSR_TFCNT      (0)      //!< Bit position for ESAI_TFSR_TFCNT.
#define BM_ESAI_TFSR_TFCNT      (0x000000ff)  //!< Bit mask for ESAI_TFSR_TFCNT.

//! @brief Get value of ESAI_TFSR_TFCNT from a register value.
#define BG_ESAI_TFSR_TFCNT(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFSR_TFCNT) >> BP_ESAI_TFSR_TFCNT)
//@}

/*! @name Register ESAI_TFSR, field NTFI[10:8] (RO)
 *
 * Next Transmitter FIFO In. Indicates which transmitter receives the next word written to the FIFO.
 *
 * Values:
 * - 000 - Transmitter #0 receives next word written to the Transmit FIFO.
 * - 001 - Transmitter #1 receives next word written to the Transmit FIFO.
 * - 010 - Transmitter #2 receives next word written to the Transmit FIFO.
 * - 011 - Transmitter #3 receives next word written to the Transmit FIFO.
 * - 100 - Transmitter #4 receives next word written to the Transmit FIFO.
 * - 101 - Transmitter #5 receives next word written to the Transmit FIFO.
 * - 110 - Reserved.
 * - 111 - Reserved.
 */
//@{
#define BP_ESAI_TFSR_NTFI      (8)      //!< Bit position for ESAI_TFSR_NTFI.
#define BM_ESAI_TFSR_NTFI      (0x00000700)  //!< Bit mask for ESAI_TFSR_NTFI.

//! @brief Get value of ESAI_TFSR_NTFI from a register value.
#define BG_ESAI_TFSR_NTFI(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFSR_NTFI) >> BP_ESAI_TFSR_NTFI)
//@}

/*! @name Register ESAI_TFSR, field NTFO[14:12] (RO)
 *
 * Next Transmitter FIFO Out. Indicates which Transmit Data Register receives the top word of the
 * Transmit FIFO. This will usually equal the lowest enabled transmitter, unless the transmit FIFO
 * is empty.
 *
 * Values:
 * - 000 - Transmitter #0 receives next word from the Transmit FIFO.
 * - 001 - Transmitter #1 receives next word from the Transmit FIFO.
 * - 010 - Transmitter #2 receives next word from the Transmit FIFO.
 * - 011 - Transmitter #3 receives next word from the Transmit FIFO.
 * - 100 - Transmitter #4 receives next word from the Transmit FIFO.
 * - 101 - Transmitter #5 receives next word from the Transmit FIFO.
 * - 110 - Reserved.
 * - 111 - Reserved.
 */
//@{
#define BP_ESAI_TFSR_NTFO      (12)      //!< Bit position for ESAI_TFSR_NTFO.
#define BM_ESAI_TFSR_NTFO      (0x00007000)  //!< Bit mask for ESAI_TFSR_NTFO.

//! @brief Get value of ESAI_TFSR_NTFO from a register value.
#define BG_ESAI_TFSR_NTFO(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TFSR_NTFO) >> BP_ESAI_TFSR_NTFO)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RFCR - Receive FIFO Configuration Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RFCR - Receive FIFO Configuration Register (RW)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_rfcr
{
    reg32_t U;
    struct _hw_esai_rfcr_bitfields
    {
        unsigned RFE : 1; //!< [0] Receive FIFO Enable.
        unsigned RFR : 1; //!< [1] Receive FIFO Reset.
        unsigned RE0 : 1; //!< [2] Receiver #0 FIFO Enable.
        unsigned RE1 : 1; //!< [3] Receiver #1 FIFO Enable.
        unsigned RE2 : 1; //!< [4] Receiver #2 FIFO Enable.
        unsigned RE3 : 1; //!< [5] Receiver #3 FIFO Enable.
        unsigned RESERVED0 : 2; //!< [7:6] Reserved
        unsigned RFWM : 8; //!< [15:8] Receive FIFO Watermark.
        unsigned RWA : 3; //!< [18:16] Receive Word Alignment.
        unsigned REXT : 1; //!< [19] Receive Extension.
        unsigned RESERVED1 : 12; //!< [31:20] Reserved
    } B;
} hw_esai_rfcr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RFCR register
 */
//@{
#define HW_ESAI_RFCR_ADDR      (REGS_ESAI_BASE + 0x18)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RFCR           (*(volatile hw_esai_rfcr_t *) HW_ESAI_RFCR_ADDR)
#define HW_ESAI_RFCR_RD()      (HW_ESAI_RFCR.U)
#define HW_ESAI_RFCR_WR(v)     (HW_ESAI_RFCR.U = (v))
#define HW_ESAI_RFCR_SET(v)    (HW_ESAI_RFCR_WR(HW_ESAI_RFCR_RD() |  (v)))
#define HW_ESAI_RFCR_CLR(v)    (HW_ESAI_RFCR_WR(HW_ESAI_RFCR_RD() & ~(v)))
#define HW_ESAI_RFCR_TOG(v)    (HW_ESAI_RFCR_WR(HW_ESAI_RFCR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_RFCR bitfields
 */

/*! @name Register ESAI_RFCR, field RFE[0] (RW)
 *
 * Receive FIFO Enable. This bit enables the use of the Receive FIFO.
 *
 * Values:
 * - 0 - Receive FIFO disabled.
 * - 1 - Receive FIFO enabled.
 */
//@{
#define BP_ESAI_RFCR_RFE      (0)      //!< Bit position for ESAI_RFCR_RFE.
#define BM_ESAI_RFCR_RFE      (0x00000001)  //!< Bit mask for ESAI_RFCR_RFE.

//! @brief Get value of ESAI_RFCR_RFE from a register value.
#define BG_ESAI_RFCR_RFE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RFE) >> BP_ESAI_RFCR_RFE)

//! @brief Format value for bitfield ESAI_RFCR_RFE.
#define BF_ESAI_RFCR_RFE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RFE) & BM_ESAI_RFCR_RFE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFE field to a new value.
#define BW_ESAI_RFCR_RFE(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RFE) | BF_ESAI_RFCR_RFE(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RFR[1] (RW)
 *
 * Receive FIFO Reset. This bit resets the Receive FIFO pointers.
 *
 * Values:
 * - 0 - Receive FIFO not reset.
 * - 1 - Receive FIFO reset.
 */
//@{
#define BP_ESAI_RFCR_RFR      (1)      //!< Bit position for ESAI_RFCR_RFR.
#define BM_ESAI_RFCR_RFR      (0x00000002)  //!< Bit mask for ESAI_RFCR_RFR.

//! @brief Get value of ESAI_RFCR_RFR from a register value.
#define BG_ESAI_RFCR_RFR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RFR) >> BP_ESAI_RFCR_RFR)

//! @brief Format value for bitfield ESAI_RFCR_RFR.
#define BF_ESAI_RFCR_RFR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RFR) & BM_ESAI_RFCR_RFR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFR field to a new value.
#define BW_ESAI_RFCR_RFR(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RFR) | BF_ESAI_RFCR_RFR(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RE0[2] (RW)
 *
 * Receiver #0 FIFO Enable. This bit enables receiver #0 to use the Receive FIFO. Do not change this
 * bit when the Receiver FIFO is enabled.
 *
 * Values:
 * - 0 - Receiver #0 is not using the Receive FIFO.
 * - 1 - Receiver #0 is using the Receive FIFO.
 */
//@{
#define BP_ESAI_RFCR_RE0      (2)      //!< Bit position for ESAI_RFCR_RE0.
#define BM_ESAI_RFCR_RE0      (0x00000004)  //!< Bit mask for ESAI_RFCR_RE0.

//! @brief Get value of ESAI_RFCR_RE0 from a register value.
#define BG_ESAI_RFCR_RE0(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RE0) >> BP_ESAI_RFCR_RE0)

//! @brief Format value for bitfield ESAI_RFCR_RE0.
#define BF_ESAI_RFCR_RE0(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RE0) & BM_ESAI_RFCR_RE0)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE0 field to a new value.
#define BW_ESAI_RFCR_RE0(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RE0) | BF_ESAI_RFCR_RE0(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RE1[3] (RW)
 *
 * Receiver #1 FIFO Enable. This bit enables receiver #1 to use the Receive FIFO. Do not change this
 * bit when the Receiver FIFO is enabled.
 *
 * Values:
 * - 0 - Receiver #1 is not using the Receive FIFO.
 * - 1 - Receiver #1 is using the Receive FIFO.
 */
//@{
#define BP_ESAI_RFCR_RE1      (3)      //!< Bit position for ESAI_RFCR_RE1.
#define BM_ESAI_RFCR_RE1      (0x00000008)  //!< Bit mask for ESAI_RFCR_RE1.

//! @brief Get value of ESAI_RFCR_RE1 from a register value.
#define BG_ESAI_RFCR_RE1(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RE1) >> BP_ESAI_RFCR_RE1)

//! @brief Format value for bitfield ESAI_RFCR_RE1.
#define BF_ESAI_RFCR_RE1(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RE1) & BM_ESAI_RFCR_RE1)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE1 field to a new value.
#define BW_ESAI_RFCR_RE1(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RE1) | BF_ESAI_RFCR_RE1(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RE2[4] (RW)
 *
 * Receiver #2 FIFO Enable. This bit enables receiver #2 to use the Receive FIFO. Do not change this
 * bit when the Receiver FIFO is enabled.
 *
 * Values:
 * - 0 - Receiver #2 is not using the Receive FIFO.
 * - 1 - Receiver #2 is using the Receive FIFO.
 */
//@{
#define BP_ESAI_RFCR_RE2      (4)      //!< Bit position for ESAI_RFCR_RE2.
#define BM_ESAI_RFCR_RE2      (0x00000010)  //!< Bit mask for ESAI_RFCR_RE2.

//! @brief Get value of ESAI_RFCR_RE2 from a register value.
#define BG_ESAI_RFCR_RE2(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RE2) >> BP_ESAI_RFCR_RE2)

//! @brief Format value for bitfield ESAI_RFCR_RE2.
#define BF_ESAI_RFCR_RE2(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RE2) & BM_ESAI_RFCR_RE2)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE2 field to a new value.
#define BW_ESAI_RFCR_RE2(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RE2) | BF_ESAI_RFCR_RE2(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RE3[5] (RW)
 *
 * Receiver #3 FIFO Enable. This bit enables receiver #3 to use the Receive FIFO. Do not change this
 * bit when the Receiver FIFO is enabled.
 *
 * Values:
 * - 0 - Receiver #3 is not using the Receive FIFO.
 * - 1 - Receiver #3 is using the Receive FIFO.
 */
//@{
#define BP_ESAI_RFCR_RE3      (5)      //!< Bit position for ESAI_RFCR_RE3.
#define BM_ESAI_RFCR_RE3      (0x00000020)  //!< Bit mask for ESAI_RFCR_RE3.

//! @brief Get value of ESAI_RFCR_RE3 from a register value.
#define BG_ESAI_RFCR_RE3(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RE3) >> BP_ESAI_RFCR_RE3)

//! @brief Format value for bitfield ESAI_RFCR_RE3.
#define BF_ESAI_RFCR_RE3(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RE3) & BM_ESAI_RFCR_RE3)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE3 field to a new value.
#define BW_ESAI_RFCR_RE3(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RE3) | BF_ESAI_RFCR_RE3(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RFWM[15:8] (RW)
 *
 * Receive FIFO Watermark. These bits configure the threshold at which the Receive FIFO Full flag
 * will set. The RFF is set when the number of words in the Receive FIFO equal or exceed the
 * selected threshold. It can be set to a non-zero value.
 */
//@{
#define BP_ESAI_RFCR_RFWM      (8)      //!< Bit position for ESAI_RFCR_RFWM.
#define BM_ESAI_RFCR_RFWM      (0x0000ff00)  //!< Bit mask for ESAI_RFCR_RFWM.

//! @brief Get value of ESAI_RFCR_RFWM from a register value.
#define BG_ESAI_RFCR_RFWM(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RFWM) >> BP_ESAI_RFCR_RFWM)

//! @brief Format value for bitfield ESAI_RFCR_RFWM.
#define BF_ESAI_RFCR_RFWM(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RFWM) & BM_ESAI_RFCR_RFWM)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFWM field to a new value.
#define BW_ESAI_RFCR_RFWM(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RFWM) | BF_ESAI_RFCR_RFWM(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field RWA[18:16] (RW)
 *
 * Receive Word Alignment. Configures the alignment of the data passed from the relevant 24 bit
 * Receive shift register and read out the ESAI Receive Data Register.
 *
 * Values:
 * - 000 - MSB of data is at bit 31. Data bits 7-0 are zeroed.
 * - 001 - MSB of data is at bit 27. Data bits 3-0 are zeroed.
 * - 010 - MSB of data is at bit 23.
 * - 011 - MSB of data is at bit 19. Data bits 3-0 from receive shift register are ignored.
 * - 100 - MSB of data is at bit 15. Data bits 7-0 from receive shift register are ignored.
 * - 101 - MSB of data is at bit 11. Data bits 11-0 from receive shift register are ignored.
 * - 110 - MSB of data is at bit 7. Data bits 15-0 from receive shift register are ignored.
 * - 111 - MSB of data is at bit 3. Data bits 19-0 from receive shift register are ignored.
 */
//@{
#define BP_ESAI_RFCR_RWA      (16)      //!< Bit position for ESAI_RFCR_RWA.
#define BM_ESAI_RFCR_RWA      (0x00070000)  //!< Bit mask for ESAI_RFCR_RWA.

//! @brief Get value of ESAI_RFCR_RWA from a register value.
#define BG_ESAI_RFCR_RWA(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_RWA) >> BP_ESAI_RFCR_RWA)

//! @brief Format value for bitfield ESAI_RFCR_RWA.
#define BF_ESAI_RFCR_RWA(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_RWA) & BM_ESAI_RFCR_RWA)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RWA field to a new value.
#define BW_ESAI_RFCR_RWA(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_RWA) | BF_ESAI_RFCR_RWA(v)))
#endif
//@}

/*! @name Register ESAI_RFCR, field REXT[19] (RW)
 *
 * Receive Extension. Enables the receive data to be returned sign extended when the Receive Word
 * Alignment is configured to return data where the MSB is not aligned with bit 31.
 *
 * Values:
 * - 0 - Receive data is zero extended.
 * - 1 - Receive data is sign extended.
 */
//@{
#define BP_ESAI_RFCR_REXT      (19)      //!< Bit position for ESAI_RFCR_REXT.
#define BM_ESAI_RFCR_REXT      (0x00080000)  //!< Bit mask for ESAI_RFCR_REXT.

//! @brief Get value of ESAI_RFCR_REXT from a register value.
#define BG_ESAI_RFCR_REXT(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFCR_REXT) >> BP_ESAI_RFCR_REXT)

//! @brief Format value for bitfield ESAI_RFCR_REXT.
#define BF_ESAI_RFCR_REXT(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RFCR_REXT) & BM_ESAI_RFCR_REXT)

#ifndef __LANGUAGE_ASM__
//! @brief Set the REXT field to a new value.
#define BW_ESAI_RFCR_REXT(v)   (HW_ESAI_RFCR_WR((HW_ESAI_RFCR_RD() & ~BM_ESAI_RFCR_REXT) | BF_ESAI_RFCR_REXT(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RFSR - Receive FIFO Status Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RFSR - Receive FIFO Status Register (RO)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_rfsr
{
    reg32_t U;
    struct _hw_esai_rfsr_bitfields
    {
        unsigned RFCNT : 8; //!< [7:0] Receive FIFO Counter.
        unsigned NRFO : 2; //!< [9:8] Next Receiver FIFO Out.
        unsigned RESERVED0 : 2; //!< [11:10] Reserved
        unsigned NRFI : 2; //!< [13:12] Next Receiver FIFO In.
        unsigned RESERVED1 : 18; //!< [31:14] Reserved
    } B;
} hw_esai_rfsr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RFSR register
 */
//@{
#define HW_ESAI_RFSR_ADDR      (REGS_ESAI_BASE + 0x1c)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RFSR           (*(volatile hw_esai_rfsr_t *) HW_ESAI_RFSR_ADDR)
#define HW_ESAI_RFSR_RD()      (HW_ESAI_RFSR.U)
#endif
//@}

/*
 * constants & macros for individual ESAI_RFSR bitfields
 */

/*! @name Register ESAI_RFSR, field RFCNT[7:0] (RO)
 *
 * Receive FIFO Counter. These bits indicate the number of data words stored in the Receive FIFO.
 */
//@{
#define BP_ESAI_RFSR_RFCNT      (0)      //!< Bit position for ESAI_RFSR_RFCNT.
#define BM_ESAI_RFSR_RFCNT      (0x000000ff)  //!< Bit mask for ESAI_RFSR_RFCNT.

//! @brief Get value of ESAI_RFSR_RFCNT from a register value.
#define BG_ESAI_RFSR_RFCNT(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFSR_RFCNT) >> BP_ESAI_RFSR_RFCNT)
//@}

/*! @name Register ESAI_RFSR, field NRFO[9:8] (RO)
 *
 * Next Receiver FIFO Out. Indicates which receiver returns the top word of the Receive FIFO.
 *
 * Values:
 * - 00 - Receiver #0 returns next word from the Receive FIFO.
 * - 01 - Receiver #1 returns next word from the Receive FIFO.
 * - 10 - Receiver #2 returns next word from the Receive FIFO.
 * - 11 - Receiver #3 returns next word from the Receive FIFO.
 */
//@{
#define BP_ESAI_RFSR_NRFO      (8)      //!< Bit position for ESAI_RFSR_NRFO.
#define BM_ESAI_RFSR_NRFO      (0x00000300)  //!< Bit mask for ESAI_RFSR_NRFO.

//! @brief Get value of ESAI_RFSR_NRFO from a register value.
#define BG_ESAI_RFSR_NRFO(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFSR_NRFO) >> BP_ESAI_RFSR_NRFO)
//@}

/*! @name Register ESAI_RFSR, field NRFI[13:12] (RO)
 *
 * Next Receiver FIFO In. Indicates which Receiver Data Register the Receive FIFO will load next.
 * This will usually equal the lowest enabled receiver, unless the receive FIFO is full.
 *
 * Values:
 * - 00 - Receiver #0 returns next word to the Receive FIFO.
 * - 01 - Receiver #1 returns next word to the Receive FIFO.
 * - 10 - Receiver #2 returns next word to the Receive FIFO.
 * - 11 - Receiver #3 returns next word to the Receive FIFO.
 */
//@{
#define BP_ESAI_RFSR_NRFI      (12)      //!< Bit position for ESAI_RFSR_NRFI.
#define BM_ESAI_RFSR_NRFI      (0x00003000)  //!< Bit mask for ESAI_RFSR_NRFI.

//! @brief Get value of ESAI_RFSR_NRFI from a register value.
#define BG_ESAI_RFSR_NRFI(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RFSR_NRFI) >> BP_ESAI_RFSR_NRFI)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TXn - Transmit Data Register n
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TXn - Transmit Data Register n (WORZ)
 *
 * Reset value: 0x00000000
 *
 * ESAI_TX5, ESAI_TX4, ESAI_TX3, ESAI_TX2, ESAI_TX1 and ESAI_TX0 are 32-bit write-only registers.
 * Data to be transmitted is written into these registers and is automatically transferred to the
 * transmit shift registers ( and ). The data written (8, 12, 16, 20, or 24 bits) should occupy the
 * most significant portion of the TXn according to the ALC control bit setting. The unused bits
 * (least significant portion and the 8 most significant bits when ALC=1) of the TXn are don't care
 * bits. The Core is interrupted whenever the TXn becomes empty if the transmit data register empty
 * interrupt has been enabled.
 */
typedef union _hw_esai_txn
{
    reg32_t U;
    struct _hw_esai_txn_bitfields
    {
        unsigned TXN : 24; //!< [23:0] Stores the data to be transmitted and is automatically transferred to the transmit shift registers.
        unsigned RESERVED0 : 8; //!< [31:24] Reserved
    } B;
} hw_esai_txn_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TXn register
 */
//@{
//! @brief Number of instances of the ESAI_TXn register.
#define HW_ESAI_TXn_COUNT     (6)

#define HW_ESAI_TXn_ADDR(n)   (REGS_ESAI_BASE + 0x80 + (0x4 * (n)))

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TXn(n)        (*(volatile hw_esai_txn_t *) HW_ESAI_TXn_ADDR(n))
#define HW_ESAI_TXn_WR(n, v)  (HW_ESAI_TXn(n).U = (v))
#endif
//@}

/*
 * constants & macros for individual ESAI_TXn bitfields
 */

/*! @name Register ESAI_TXn, field TXN[23:0] (WORZ)
 *
 * Stores the data to be transmitted and is automatically transferred to the transmit shift
 * registers. See .
 */
//@{
#define BP_ESAI_TXn_TXN      (0)      //!< Bit position for ESAI_TXn_TXN.
#define BM_ESAI_TXn_TXN      (0x00ffffff)  //!< Bit mask for ESAI_TXn_TXN.

//! @brief Get value of ESAI_TXn_TXN from a register value.
#define BG_ESAI_TXn_TXN(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TXn_TXN) >> BP_ESAI_TXn_TXN)

//! @brief Format value for bitfield ESAI_TXn_TXN.
#define BF_ESAI_TXn_TXN(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TXn_TXN) & BM_ESAI_TXn_TXN)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TSR - ESAI Transmit Slot Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TSR - ESAI Transmit Slot Register (WORZ)
 *
 * Reset value: 0x00000000
 */
typedef union _hw_esai_tsr
{
    reg32_t U;
    struct _hw_esai_tsr_bitfields
    {
        unsigned TSR : 24; //!< [23:0] The write-only Transmit Slot Register (ESAI_TSR) is effectively a null data register that is used when the data is not to be transmitted in the available transmit time slot.
        unsigned RESERVED0 : 8; //!< [31:24] Reserved
    } B;
} hw_esai_tsr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TSR register
 */
//@{
#define HW_ESAI_TSR_ADDR      (REGS_ESAI_BASE + 0x98)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TSR           (*(volatile hw_esai_tsr_t *) HW_ESAI_TSR_ADDR)
#define HW_ESAI_TSR_WR(v)     (HW_ESAI_TSR.U = (v))
#endif
//@}

/*
 * constants & macros for individual ESAI_TSR bitfields
 */

/*! @name Register ESAI_TSR, field TSR[23:0] (WORZ)
 *
 * The write-only Transmit Slot Register (ESAI_TSR) is effectively a null data register that is used
 * when the data is not to be transmitted in the available transmit time slot. The transmit data
 * pins of all the enabled transmitters are in the high-impedance state for the respective time slot
 * where TSR has been written. The Transmitter External Buffer Enable pin (FSR pin when SYN=1,
 * TEBE=1, RFSD=1) disables the external buffers during the slot when the ESAI_TSR register has been
 * written.
 */
//@{
#define BP_ESAI_TSR_TSR      (0)      //!< Bit position for ESAI_TSR_TSR.
#define BM_ESAI_TSR_TSR      (0x00ffffff)  //!< Bit mask for ESAI_TSR_TSR.

//! @brief Get value of ESAI_TSR_TSR from a register value.
#define BG_ESAI_TSR_TSR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TSR_TSR) >> BP_ESAI_TSR_TSR)

//! @brief Format value for bitfield ESAI_TSR_TSR.
#define BF_ESAI_TSR_TSR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TSR_TSR) & BM_ESAI_TSR_TSR)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RXn - Receive Data Register n
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RXn - Receive Data Register n (RO)
 *
 * Reset value: 0x00000000
 *
 * ESAI_RX3, ESAI_RX2, ESAI_RX1, and ESAI_RX0 are 32-bit read-only registers that accept data from
 * the receive shift registers when they become full ( and ). The data occupies the most significant
 * portion of the receive data registers, according to the ALC control bit setting. The unused bits
 * (least significant portion and 8 most significant bits when ALC=1) read as zeros. The Core is
 * interrupted whenever RXn becomes full if the associated interrupt is enabled.
 */
typedef union _hw_esai_rxn
{
    reg32_t U;
    struct _hw_esai_rxn_bitfields
    {
        unsigned RXN : 24; //!< [23:0] Accept data from the receive shift registers when they become full
        unsigned RESERVED0 : 8; //!< [31:24] Reserved
    } B;
} hw_esai_rxn_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RXn register
 */
//@{
//! @brief Number of instances of the ESAI_RXn register.
#define HW_ESAI_RXn_COUNT     (4)

#define HW_ESAI_RXn_ADDR(n)   (REGS_ESAI_BASE + 0xa0 + (0x4 * (n)))

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RXn(n)        (*(volatile hw_esai_rxn_t *) HW_ESAI_RXn_ADDR(n))
#define HW_ESAI_RXn_RD(n)     (HW_ESAI_RXn(n).U)
#endif
//@}

/*
 * constants & macros for individual ESAI_RXn bitfields
 */

/*! @name Register ESAI_RXn, field RXN[23:0] (RO)
 *
 * Accept data from the receive shift registers when they become full See
 */
//@{
#define BP_ESAI_RXn_RXN      (0)      //!< Bit position for ESAI_RXn_RXN.
#define BM_ESAI_RXn_RXN      (0x00ffffff)  //!< Bit mask for ESAI_RXn_RXN.

//! @brief Get value of ESAI_RXn_RXN from a register value.
#define BG_ESAI_RXn_RXN(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RXn_RXN) >> BP_ESAI_RXn_RXN)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_SAISR - Serial Audio Interface Status Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_SAISR - Serial Audio Interface Status Register (RO)
 *
 * Reset value: 0x00000000
 *
 * The Status Register (ESAI_SAISR) is a read-only status register used by the ARM Core to read the
 * status and serial input flags of the ESAI.
 */
typedef union _hw_esai_saisr
{
    reg32_t U;
    struct _hw_esai_saisr_bitfields
    {
        unsigned IF0 : 1; //!< [0] ESAI_SAISR Serial Input Flag 0.
        unsigned IF1 : 1; //!< [1] ESAI_SAISR Serial Inout Flag 1.
        unsigned IF2 : 1; //!< [2] ESAI_SAISR Serial Input Flag 2.
        unsigned RESERVED0 : 3; //!< [5:3] Reserved.
        unsigned RFS : 1; //!< [6] ESAI_SAISR Receive Frame Sync Flag.
        unsigned ROE : 1; //!< [7] ESAI_SAISR Receive Overrun Error Flag.
        unsigned RDF : 1; //!< [8] ESAI_SAISR Receive Data Register Full.
        unsigned REDF : 1; //!< [9] ESAI_SAISR Receive Even-Data Register Full.
        unsigned RODF : 1; //!< [10] ESAI_SAISR Receive Odd-Data Register Full.
        unsigned RESERVED1 : 2; //!< [12:11] Reserved.
        unsigned TFS : 1; //!< [13] ESAI_SAISR Transmit Frame Sync Flag.
        unsigned TUE : 1; //!< [14] ESAI_SAISR Transmit Underrun Error Flag.
        unsigned TDE : 1; //!< [15] ESAI_SAISR Transmit Data Register Empty.
        unsigned TEDE : 1; //!< [16] ESAI_SAISR Transmit Even-DataRegister Empty.
        unsigned TODFE : 1; //!< [17] ESAI_SAISR Transmit Odd-Data Register Empty.
        unsigned RESERVED2 : 14; //!< [31:18] Reserved.
    } B;
} hw_esai_saisr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_SAISR register
 */
//@{
#define HW_ESAI_SAISR_ADDR      (REGS_ESAI_BASE + 0xcc)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_SAISR           (*(volatile hw_esai_saisr_t *) HW_ESAI_SAISR_ADDR)
#define HW_ESAI_SAISR_RD()      (HW_ESAI_SAISR.U)
#endif
//@}

/*
 * constants & macros for individual ESAI_SAISR bitfields
 */

/*! @name Register ESAI_SAISR, field IF0[0] (RO)
 *
 * ESAI_SAISR Serial Input Flag 0. The IF0 bit is enabled only when the SCKR pin is defined as ESAI
 * in the Port Control Register, SYN=1 and RCKD=0, indicating that SCKR is an input flag and the
 * synchronous mode is selected. Data present on the SCKR pin is latched during reception of the
 * first received data bit after frame sync is detected. The IF0 bit is updated with this data when
 * the receiver shift registers are transferred into the receiver data registers. IF0 reads as a
 * zero when it is not enabled. Hardware, software, ESAI individual reset clear IF0.
 */
//@{
#define BP_ESAI_SAISR_IF0      (0)      //!< Bit position for ESAI_SAISR_IF0.
#define BM_ESAI_SAISR_IF0      (0x00000001)  //!< Bit mask for ESAI_SAISR_IF0.

//! @brief Get value of ESAI_SAISR_IF0 from a register value.
#define BG_ESAI_SAISR_IF0(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_IF0) >> BP_ESAI_SAISR_IF0)
//@}

/*! @name Register ESAI_SAISR, field IF1[1] (RO)
 *
 * ESAI_SAISR Serial Inout Flag 1. The IF1 bit is enabled only when the FSR pin is defined as ESAI
 * in the Port Control Register, SYN =1, RFSD=0 and TEBE=0, indicating that FSR is an input flag and
 * the synchronous mode is selected. Data present on the FSR pin is latched during reception of the
 * first received data bit after frame sync is detected. The IF1 bit is updated with this data when
 * the receiver shift registers are transferred into the receiver data registers. IF1 reads as a
 * zero when it is not enabled. Hardware, software, ESAI individual reset clear IF1.
 */
//@{
#define BP_ESAI_SAISR_IF1      (1)      //!< Bit position for ESAI_SAISR_IF1.
#define BM_ESAI_SAISR_IF1      (0x00000002)  //!< Bit mask for ESAI_SAISR_IF1.

//! @brief Get value of ESAI_SAISR_IF1 from a register value.
#define BG_ESAI_SAISR_IF1(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_IF1) >> BP_ESAI_SAISR_IF1)
//@}

/*! @name Register ESAI_SAISR, field IF2[2] (RO)
 *
 * ESAI_SAISR Serial Input Flag 2. The IF2 bit is enabled only when the HCKR pin is defined as ESAI
 * in the Port Control Register, SYN=1 and RHCKD=0, indicating that HCKR is an input flag and the
 * synchronous mode is selected. Data present on the HCKR pin is latched during reception of the
 * first received data bit after frame sync is detected. The IF2 bit is updated with this data when
 * the receive shift registers are transferred into the receiver data registers. IF2 reads as a zero
 * when it is not enabled. Hardware, software, ESAI individual reset clear IF2.
 */
//@{
#define BP_ESAI_SAISR_IF2      (2)      //!< Bit position for ESAI_SAISR_IF2.
#define BM_ESAI_SAISR_IF2      (0x00000004)  //!< Bit mask for ESAI_SAISR_IF2.

//! @brief Get value of ESAI_SAISR_IF2 from a register value.
#define BG_ESAI_SAISR_IF2(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_IF2) >> BP_ESAI_SAISR_IF2)
//@}

/*! @name Register ESAI_SAISR, field RFS[6] (RO)
 *
 * ESAI_SAISR Receive Frame Sync Flag. When set, RFS indicates that a receive frame sync occurred
 * during reception of the words in the receiver data registers. This indicates that the data words
 * are from the first slot in the frame. When RFS is clear and a word is received, it indicates
 * (only in the network mode) that the frame sync did not occur during reception of that word. RFS
 * is cleared by hardware, software, ESAI individual reset. RFS is valid only if at least one of the
 * receivers is enabled (REx=1). (In normal mode, RFS always reads as a one when reading data
 * because there is only one time slot per frame - the "frame sync" time slot)
 */
//@{
#define BP_ESAI_SAISR_RFS      (6)      //!< Bit position for ESAI_SAISR_RFS.
#define BM_ESAI_SAISR_RFS      (0x00000040)  //!< Bit mask for ESAI_SAISR_RFS.

//! @brief Get value of ESAI_SAISR_RFS from a register value.
#define BG_ESAI_SAISR_RFS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_RFS) >> BP_ESAI_SAISR_RFS)
//@}

/*! @name Register ESAI_SAISR, field ROE[7] (RO)
 *
 * ESAI_SAISR Receive Overrun Error Flag. The ROE flag is set when the serial receive shift register
 * of an enabled receiver is full and ready to transfer to its receiver data register (RXn) and the
 * register is already full (RDF=1). If REIE is set, an ESAI receive data with exception (overrun
 * error) interrupt request is issued when ROE is set. Hardware, software, ESAI individual reset
 * clear ROE. ROE is also cleared by reading the SAISR with ROE set, followed by reading all the
 * enabled receive data registers.
 */
//@{
#define BP_ESAI_SAISR_ROE      (7)      //!< Bit position for ESAI_SAISR_ROE.
#define BM_ESAI_SAISR_ROE      (0x00000080)  //!< Bit mask for ESAI_SAISR_ROE.

//! @brief Get value of ESAI_SAISR_ROE from a register value.
#define BG_ESAI_SAISR_ROE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_ROE) >> BP_ESAI_SAISR_ROE)
//@}

/*! @name Register ESAI_SAISR, field RDF[8] (RO)
 *
 * ESAI_SAISR Receive Data Register Full. RDF is set when the contents of the receive shift register
 * of an enabled receiver is transferred to the respective receive data register. RDF is cleared
 * when the Core reads the receive data register of all enabled receivers or cleared by hardware,
 * software, ESAI individual reset. If RIE is set, an ESAI receive data interrupt request is issued
 * when RDF is set.
 */
//@{
#define BP_ESAI_SAISR_RDF      (8)      //!< Bit position for ESAI_SAISR_RDF.
#define BM_ESAI_SAISR_RDF      (0x00000100)  //!< Bit mask for ESAI_SAISR_RDF.

//! @brief Get value of ESAI_SAISR_RDF from a register value.
#define BG_ESAI_SAISR_RDF(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_RDF) >> BP_ESAI_SAISR_RDF)
//@}

/*! @name Register ESAI_SAISR, field REDF[9] (RO)
 *
 * ESAI_SAISR Receive Even-Data Register Full. When set, REDF indicates that the received data in
 * the receive data registers of the enabled receivers have arrived during an even time slot when
 * operating in the network mode. Even time slots are all even-numbered slots (0, 2, 4, 6, and so
 * on). Time slots are numbered from zero to N-1, where N is the number of time slots in the frame.
 * The zero time slot is considered even. REDF is set when the contents of the receive shift
 * registers are transferred to the receive data registers. REDF is cleared when the Core reads all
 * the enabled receive data registers or cleared by hardware, software, ESAI individual resets. If
 * REDIE is set, an ESAI receive even slot data interrupt request is issued when REDF is set.
 */
//@{
#define BP_ESAI_SAISR_REDF      (9)      //!< Bit position for ESAI_SAISR_REDF.
#define BM_ESAI_SAISR_REDF      (0x00000200)  //!< Bit mask for ESAI_SAISR_REDF.

//! @brief Get value of ESAI_SAISR_REDF from a register value.
#define BG_ESAI_SAISR_REDF(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_REDF) >> BP_ESAI_SAISR_REDF)
//@}

/*! @name Register ESAI_SAISR, field RODF[10] (RO)
 *
 * ESAI_SAISR Receive Odd-Data Register Full. When set, RODF indicates that the received data in the
 * receive data registers of the enabled receivers have arrived during an odd time slot when
 * operating in the network mode. Odd time slots are all odd-numbered slots (1, 3, 5, and so on).
 * Time slots are numbered from zero to N-1, where N is the number of time slots in the frame. RODF
 * is set when the contents of the receive shift registers are transferred to the receive data
 * registers. RODF is cleared when the Core reads all the enabled receive data registers or cleared
 * by hardware, software, ESAI individual resets.
 */
//@{
#define BP_ESAI_SAISR_RODF      (10)      //!< Bit position for ESAI_SAISR_RODF.
#define BM_ESAI_SAISR_RODF      (0x00000400)  //!< Bit mask for ESAI_SAISR_RODF.

//! @brief Get value of ESAI_SAISR_RODF from a register value.
#define BG_ESAI_SAISR_RODF(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_RODF) >> BP_ESAI_SAISR_RODF)
//@}

/*! @name Register ESAI_SAISR, field TFS[13] (RO)
 *
 * ESAI_SAISR Transmit Frame Sync Flag. When set, TFS indicates that a transmit frame sync occurred
 * in the current time slot. TFS is set at the start of the first time slot in the frame and cleared
 * during all other time slots. Data written to a transmit data register during the time slot when
 * TFS is set is transmitted (in network mode), if the transmitter is enabled, during the second
 * time slot in the frame. TFS is useful in network mode to identify the start of a frame. TFS is
 * cleared by hardware, software, ESAI individual reset. TFS is valid only if at least one
 * transmitter is enabled, that is, one or more of TE0, TE1, TE2, TE3, TE4 and TE5 are set. (In
 * normal mode, TFS always reads as a one when transmitting data because there is only one time slot
 * per frame - the "frame sync" time slot)
 */
//@{
#define BP_ESAI_SAISR_TFS      (13)      //!< Bit position for ESAI_SAISR_TFS.
#define BM_ESAI_SAISR_TFS      (0x00002000)  //!< Bit mask for ESAI_SAISR_TFS.

//! @brief Get value of ESAI_SAISR_TFS from a register value.
#define BG_ESAI_SAISR_TFS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_TFS) >> BP_ESAI_SAISR_TFS)
//@}

/*! @name Register ESAI_SAISR, field TUE[14] (RO)
 *
 * ESAI_SAISR Transmit Underrun Error Flag. TUE is set when at least one of the enabled serial
 * transmit shift registers is empty (no new data to be transmitted) and a transmit time slot
 * occurs. When a transmit underrun error occurs, the previous data (which is still present in the
 * TX registers that were not written) is retransmitted. If TEIE is set, an ESAI transmit data with
 * exception (underrun error) interrupt request is issued when TUE is set. Hardware, software, ESAI
 * individual reset clear TUE. TUE is also cleared by reading the ESAI_SAISR with TUE set, followed
 * by writing to all the enabled transmit data registers or to ESAI_TSR.
 */
//@{
#define BP_ESAI_SAISR_TUE      (14)      //!< Bit position for ESAI_SAISR_TUE.
#define BM_ESAI_SAISR_TUE      (0x00004000)  //!< Bit mask for ESAI_SAISR_TUE.

//! @brief Get value of ESAI_SAISR_TUE from a register value.
#define BG_ESAI_SAISR_TUE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_TUE) >> BP_ESAI_SAISR_TUE)
//@}

/*! @name Register ESAI_SAISR, field TDE[15] (RO)
 *
 * ESAI_SAISR Transmit Data Register Empty. TDE is set when the contents of the transmit data
 * register of all the enabled transmitters are transferred to the transmit shift registers; it is
 * also set for a TSR disabled time slot period in network mode (as if data were being transmitted
 * after the TSR was written). When set, TDE indicates that data should be written to all the TX
 * registers of the enabled transmitters or to the transmit slot register (ESAI_TSR). TDE is cleared
 * when the Core writes to all the transmit data registers of the enabled transmitters, or when the
 * Core writes to the TSR to disable transmission of the next time slot. If TIE is set, an ESAI
 * transmit data interrupt request is issued when TDE is set. Hardware, software, ESAI individual
 * reset clear TDE.
 */
//@{
#define BP_ESAI_SAISR_TDE      (15)      //!< Bit position for ESAI_SAISR_TDE.
#define BM_ESAI_SAISR_TDE      (0x00008000)  //!< Bit mask for ESAI_SAISR_TDE.

//! @brief Get value of ESAI_SAISR_TDE from a register value.
#define BG_ESAI_SAISR_TDE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_TDE) >> BP_ESAI_SAISR_TDE)
//@}

/*! @name Register ESAI_SAISR, field TEDE[16] (RO)
 *
 * ESAI_SAISR Transmit Even-DataRegister Empty. When set, TEDE indicates that the enabled
 * transmitter data registers became empty at the beginning of an even time slot. Even time slots
 * are all even-numbered slots (0, 2, 4, 6, etc.). Time slots are numbered from zero to N-1, where N
 * is the number of time slots in the frame. The zero time slot is considered even. This flag is set
 * when the contents of the transmit data register of all the enabled transmitters are transferred
 * to the transmit shift registers; it is also set for a TSR disabled time slot period in network
 * mode (as if data were being transmitted after the TSR was written). When set, TEDE indicates that
 * data should be written to all the TX registers of the enabled transmitters or to the transmit
 * slot register (ESAI_TSR). TEDE is cleared when the Core writes to all the transmit data registers
 * of the enabled transmitters, or when the Core writes to the TSR to disable transmission of the
 * next time slot. If TIE is set, an ESAI transmit data interrupt request is issued when TEDE is
 * set. Hardware, software, ESAI individual reset clear TEDE.
 */
//@{
#define BP_ESAI_SAISR_TEDE      (16)      //!< Bit position for ESAI_SAISR_TEDE.
#define BM_ESAI_SAISR_TEDE      (0x00010000)  //!< Bit mask for ESAI_SAISR_TEDE.

//! @brief Get value of ESAI_SAISR_TEDE from a register value.
#define BG_ESAI_SAISR_TEDE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_TEDE) >> BP_ESAI_SAISR_TEDE)
//@}

/*! @name Register ESAI_SAISR, field TODFE[17] (RO)
 *
 * ESAI_SAISR Transmit Odd-Data Register Empty. When set, TODFE indicates that the enabled
 * transmitter data registers became empty at the beginning of an odd time slot. Odd time slots are
 * all odd-numbered slots (1, 3, 5, and so on). Time slots are numbered from zero to N-1, where N is
 * the number of time slots in the frame. This flag is set when the contents of the transmit data
 * register of all the enabled transmitters are transferred to the transmit shift registers; it is
 * also set for a TSR disabled time slot period in network mode (as if data were being transmitted
 * after the TSR was written). When set, TODFE indicates that data should be written to all the TX
 * registers of the enabled transmitters or to the transmit slot register (ESAI_TSR). TODE is
 * cleared when the Core writes to all the transmit data registers of the enabled transmitters, or
 * when the Core writes to the TSR to disable transmission of the next time slot. If TIE is set, an
 * ESAI transmit data interrupt request is issued when TODFE is set. Hardware, software, ESAI
 * individual reset clear TODFE.
 */
//@{
#define BP_ESAI_SAISR_TODFE      (17)      //!< Bit position for ESAI_SAISR_TODFE.
#define BM_ESAI_SAISR_TODFE      (0x00020000)  //!< Bit mask for ESAI_SAISR_TODFE.

//! @brief Get value of ESAI_SAISR_TODFE from a register value.
#define BG_ESAI_SAISR_TODFE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAISR_TODFE) >> BP_ESAI_SAISR_TODFE)
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_SAICR - Serial Audio Interface Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_SAICR - Serial Audio Interface Control Register (RW)
 *
 * Reset value: 0x00000000
 *
 * The read/write Common Control Register (ESAI_SAICR) contains control bits for functions that
 * affect both the receive and transmit sections of the ESAI. SAICR SYN Bit Operation
 */
typedef union _hw_esai_saicr
{
    reg32_t U;
    struct _hw_esai_saicr_bitfields
    {
        unsigned OF0 : 1; //!< [0] ESAI_SAICR Serial Output Flag 0.
        unsigned OF1 : 1; //!< [1] ESAI_SAICR Serial Output Flag 1.
        unsigned OF2 : 1; //!< [2] ESAI_SAICR Serial Output Flag 2.
        unsigned RESERVED0 : 3; //!< [5:3] Reserved.
        unsigned SYN : 1; //!< [6] ESAI_SAICR Synchronous Mode Selection.
        unsigned TEBE : 1; //!< [7] ESAI_SAICR Transmit External Buffer Enable.
        unsigned ALC : 1; //!< [8] ESAI_SAICR Alignment Control.
        unsigned RESERVED1 : 23; //!< [31:9] Reserved
    } B;
} hw_esai_saicr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_SAICR register
 */
//@{
#define HW_ESAI_SAICR_ADDR      (REGS_ESAI_BASE + 0xd0)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_SAICR           (*(volatile hw_esai_saicr_t *) HW_ESAI_SAICR_ADDR)
#define HW_ESAI_SAICR_RD()      (HW_ESAI_SAICR.U)
#define HW_ESAI_SAICR_WR(v)     (HW_ESAI_SAICR.U = (v))
#define HW_ESAI_SAICR_SET(v)    (HW_ESAI_SAICR_WR(HW_ESAI_SAICR_RD() |  (v)))
#define HW_ESAI_SAICR_CLR(v)    (HW_ESAI_SAICR_WR(HW_ESAI_SAICR_RD() & ~(v)))
#define HW_ESAI_SAICR_TOG(v)    (HW_ESAI_SAICR_WR(HW_ESAI_SAICR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_SAICR bitfields
 */

/*! @name Register ESAI_SAICR, field OF0[0] (RW)
 *
 * ESAI_SAICR Serial Output Flag 0. The Serial Output Flag 0 (OF0) is a data bit used to hold data
 * to be send to the OF0 pin. When the ESAI is in the synchronous clock mode (SYN=1), the SCKR pin
 * is configured as the ESAI flag 0. If the receiver serial clock direction bit (RCKD) is set, the
 * SCKR pin is the output flag OF0, and data present in the OF0 bit is written to the OF0 pin at the
 * beginning of the frame in normal mode or at the beginning of the next time slot in network mode.
 */
//@{
#define BP_ESAI_SAICR_OF0      (0)      //!< Bit position for ESAI_SAICR_OF0.
#define BM_ESAI_SAICR_OF0      (0x00000001)  //!< Bit mask for ESAI_SAICR_OF0.

//! @brief Get value of ESAI_SAICR_OF0 from a register value.
#define BG_ESAI_SAICR_OF0(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAICR_OF0) >> BP_ESAI_SAICR_OF0)

//! @brief Format value for bitfield ESAI_SAICR_OF0.
#define BF_ESAI_SAICR_OF0(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_SAICR_OF0) & BM_ESAI_SAICR_OF0)

#ifndef __LANGUAGE_ASM__
//! @brief Set the OF0 field to a new value.
#define BW_ESAI_SAICR_OF0(v)   (HW_ESAI_SAICR_WR((HW_ESAI_SAICR_RD() & ~BM_ESAI_SAICR_OF0) | BF_ESAI_SAICR_OF0(v)))
#endif
//@}

/*! @name Register ESAI_SAICR, field OF1[1] (RW)
 *
 * ESAI_SAICR Serial Output Flag 1. The Serial Output Flag 1 (OF1) is a data bit used to hold data
 * to be send to the OF1 pin. When the ESAI is in the synchronous clock mode (SYN=1), the FSR pin is
 * configured as the ESAI flag 1. If the receiver frame sync direction bit (RFSD) is set and the
 * TEBE bit is cleared, the FSR pin is the output flag OF1, and data present in the OF1 bit is
 * written to the OF1 pin at the beginning of the frame in normal mode or at the beginning of the
 * next time slot in network mode.
 */
//@{
#define BP_ESAI_SAICR_OF1      (1)      //!< Bit position for ESAI_SAICR_OF1.
#define BM_ESAI_SAICR_OF1      (0x00000002)  //!< Bit mask for ESAI_SAICR_OF1.

//! @brief Get value of ESAI_SAICR_OF1 from a register value.
#define BG_ESAI_SAICR_OF1(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAICR_OF1) >> BP_ESAI_SAICR_OF1)

//! @brief Format value for bitfield ESAI_SAICR_OF1.
#define BF_ESAI_SAICR_OF1(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_SAICR_OF1) & BM_ESAI_SAICR_OF1)

#ifndef __LANGUAGE_ASM__
//! @brief Set the OF1 field to a new value.
#define BW_ESAI_SAICR_OF1(v)   (HW_ESAI_SAICR_WR((HW_ESAI_SAICR_RD() & ~BM_ESAI_SAICR_OF1) | BF_ESAI_SAICR_OF1(v)))
#endif
//@}

/*! @name Register ESAI_SAICR, field OF2[2] (RW)
 *
 * ESAI_SAICR Serial Output Flag 2. The Serial Output Flag 2 (OF2) is a data bit used to hold data
 * to be send to the OF2 pin. When the ESAI is in the synchronous clock mode (SYN=1), the HCKR pin
 * is configured as the ESAI flag 2. If the receiver high frequency clock direction bit (RHCKD) is
 * set, the HCKR pin is the output flag OF2, and data present in the OF2 bit is written to the OF2
 * pin at the beginning of the frame in normal mode or at the beginning of the next time slot in
 * network mode.
 */
//@{
#define BP_ESAI_SAICR_OF2      (2)      //!< Bit position for ESAI_SAICR_OF2.
#define BM_ESAI_SAICR_OF2      (0x00000004)  //!< Bit mask for ESAI_SAICR_OF2.

//! @brief Get value of ESAI_SAICR_OF2 from a register value.
#define BG_ESAI_SAICR_OF2(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAICR_OF2) >> BP_ESAI_SAICR_OF2)

//! @brief Format value for bitfield ESAI_SAICR_OF2.
#define BF_ESAI_SAICR_OF2(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_SAICR_OF2) & BM_ESAI_SAICR_OF2)

#ifndef __LANGUAGE_ASM__
//! @brief Set the OF2 field to a new value.
#define BW_ESAI_SAICR_OF2(v)   (HW_ESAI_SAICR_WR((HW_ESAI_SAICR_RD() & ~BM_ESAI_SAICR_OF2) | BF_ESAI_SAICR_OF2(v)))
#endif
//@}

/*! @name Register ESAI_SAICR, field SYN[6] (RW)
 *
 * ESAI_SAICR Synchronous Mode Selection. The Synchronous Mode Selection (SYN) bit controls whether
 * the receiver and transmitter sections of the ESAI operate synchronously or asynchronously with
 * respect to each other (see Port C Control Register ). When SYN is cleared, the asynchronous mode
 * is chosen and independent clock and frame sync signals are used for the transmit and receive
 * sections. When SYN is set, the synchronous mode is chosen and the transmit and receive sections
 * use common clock and frame sync signals. When in the synchronous mode (SYN=1), the transmit and
 * receive sections use the transmitter section clock generator as the source of the clock and frame
 * sync for both sections. Also, the receiver clock pins SCKR, FSR and HCKR now operate as I/O
 * flags. Refer to , , and for the effects of SYN on the receiver clock pins.
 */
//@{
#define BP_ESAI_SAICR_SYN      (6)      //!< Bit position for ESAI_SAICR_SYN.
#define BM_ESAI_SAICR_SYN      (0x00000040)  //!< Bit mask for ESAI_SAICR_SYN.

//! @brief Get value of ESAI_SAICR_SYN from a register value.
#define BG_ESAI_SAICR_SYN(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAICR_SYN) >> BP_ESAI_SAICR_SYN)

//! @brief Format value for bitfield ESAI_SAICR_SYN.
#define BF_ESAI_SAICR_SYN(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_SAICR_SYN) & BM_ESAI_SAICR_SYN)

#ifndef __LANGUAGE_ASM__
//! @brief Set the SYN field to a new value.
#define BW_ESAI_SAICR_SYN(v)   (HW_ESAI_SAICR_WR((HW_ESAI_SAICR_RD() & ~BM_ESAI_SAICR_SYN) | BF_ESAI_SAICR_SYN(v)))
#endif
//@}

/*! @name Register ESAI_SAICR, field TEBE[7] (RW)
 *
 * ESAI_SAICR Transmit External Buffer Enable. The Transmitter External Buffer Enable (TEBE) bit
 * controls the function of the FSR pin when in the synchronous mode. If the ESAI is configured for
 * operation in the synchronous mode (SYN=1), and TEBE is set while FSR pin is configured as an
 * output (RFSD=1), the FSR pin functions as the transmitter external buffer enable control to
 * enable the use of an external buffers on the transmitter outputs. If TEBE is cleared, the FSR pin
 * functions as the serial I/O flag 1. See Port C Control Register for a summary of the effects of
 * TEBE on the FSR pin.
 */
//@{
#define BP_ESAI_SAICR_TEBE      (7)      //!< Bit position for ESAI_SAICR_TEBE.
#define BM_ESAI_SAICR_TEBE      (0x00000080)  //!< Bit mask for ESAI_SAICR_TEBE.

//! @brief Get value of ESAI_SAICR_TEBE from a register value.
#define BG_ESAI_SAICR_TEBE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAICR_TEBE) >> BP_ESAI_SAICR_TEBE)

//! @brief Format value for bitfield ESAI_SAICR_TEBE.
#define BF_ESAI_SAICR_TEBE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_SAICR_TEBE) & BM_ESAI_SAICR_TEBE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TEBE field to a new value.
#define BW_ESAI_SAICR_TEBE(v)   (HW_ESAI_SAICR_WR((HW_ESAI_SAICR_RD() & ~BM_ESAI_SAICR_TEBE) | BF_ESAI_SAICR_TEBE(v)))
#endif
//@}

/*! @name Register ESAI_SAICR, field ALC[8] (RW)
 *
 * ESAI_SAICR Alignment Control. The ESAI is designed for 24-bit fractional data, thus shorter data
 * words are left aligned to the MSB (bit 23). Some applications use 16-bit fractional data. In
 * those cases, shorter data words may be left aligned to bit 15. The Alignment Control (ALC) bit
 * supports these applications. If ALC is set, transmitted and received words are left aligned to
 * bit 15 in the transmit and receive shift registers. If ALC is cleared, transmitted and received
 * word are left aligned to bit 23 in the transmit and receive shift registers. While ALC is set,
 * 20-bit and 24-bit words may not be used, and word length control should specify 8-, 12-, or
 * 16-bit words; otherwise, results are unpredictable.
 */
//@{
#define BP_ESAI_SAICR_ALC      (8)      //!< Bit position for ESAI_SAICR_ALC.
#define BM_ESAI_SAICR_ALC      (0x00000100)  //!< Bit mask for ESAI_SAICR_ALC.

//! @brief Get value of ESAI_SAICR_ALC from a register value.
#define BG_ESAI_SAICR_ALC(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_SAICR_ALC) >> BP_ESAI_SAICR_ALC)

//! @brief Format value for bitfield ESAI_SAICR_ALC.
#define BF_ESAI_SAICR_ALC(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_SAICR_ALC) & BM_ESAI_SAICR_ALC)

#ifndef __LANGUAGE_ASM__
//! @brief Set the ALC field to a new value.
#define BW_ESAI_SAICR_ALC(v)   (HW_ESAI_SAICR_WR((HW_ESAI_SAICR_RD() & ~BM_ESAI_SAICR_ALC) | BF_ESAI_SAICR_ALC(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TCR - Transmit Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TCR - Transmit Control Register (RW)
 *
 * Reset value: 0x00000000
 *
 * The read/write Transmit Control Register (ESAI_TCR) controls the ESAI transmitter section.
 * Interrupt enable bits for the transmitter section are provided in this control register.
 * Operating modes are also selected in this register. Transmit Network Mode Selection TMOD1 TMOD0
 * TDC4-TDC0 Transmitter Network Mode 0 0 0x0-0x1F Normal Mode 0 1 0x0 On-Demand Mode 0 1 0x1-0x1F
 * Network Mode 1 0 X Reserved 1 1 0x0C AC97 Normal and Network Operation ESAI Transmit Slot and
 * Word Length Selection TSWS4 TSWS3 TSWS2 TSWS1 TSWS0 SLOT LENGTH WORD LENGTH 0 0 0 0 0 8 8 0 0 1 0
 * 0 12 8 0 0 0 0 1 12 0 1 0 0 0 16 8 0 0 1 0 1 12 0 0 0 1 0 16 0 1 1 0 0 20 8 0 1 0 0 1 12 0 0 1 1
 * 0 16 0 0 0 1 1 20 1 0 0 0 0 24 8 0 1 1 0 1 12 0 1 0 1 0 16 0 0 1 1 1 20 1 1 1 1 0 24 1 1 0 0 0 32
 * 8 1 0 1 0 1 12 1 0 0 1 0 16 0 1 1 1 1 20 1 1 1 1 1 24 0 1 0 1 1 Reserved 0 1 1 1 0 1 0 0 0 1 1 0
 * 0 1 1 1 0 1 0 0 1 0 1 1 0 1 0 1 1 1 1 1 0 0 1 1 1 0 1 0 1 1 0 1 1 1 1 1 0 0 1 1 1 0 1 Frame
 * Length Selection
 */
typedef union _hw_esai_tcr
{
    reg32_t U;
    struct _hw_esai_tcr_bitfields
    {
        unsigned TE0 : 1; //!< [0] ESAI_TCR ESAI Transmit 0 Enable.
        unsigned TE1 : 1; //!< [1] ESAI_TCR ESAI Transmit 1 Enable.
        unsigned TE2 : 1; //!< [2] ESAI_TCR ESAI Transmit 2 Enable.
        unsigned TE3 : 1; //!< [3] ESAI_TCR ESAI Transmit 3 Enable.
        unsigned TE4 : 1; //!< [4] ESAI_TCR ESAI Transmit 4 Enable.
        unsigned TE5 : 1; //!< [5] ESAI_TCR ESAI Transmit 5 Enable.
        unsigned TSHFD : 1; //!< [6] ESAI_TCR Transmit Shift Direction.
        unsigned TWA : 1; //!< [7] ESAI_TCR Transmit Word Alignment Control.
        unsigned TMOD : 2; //!< [9:8] ESAI_TCR Transmit Network Mode Control (TMOD1-TMOD0).
        unsigned TSWS : 5; //!< [14:10] ESAI_TCR Tx Slot and Word Length Select (TSWS4-TSWS0).
        unsigned TFSL : 1; //!< [15] ESAI_TCR Transmit Frame Sync Length.
        unsigned TFSR : 1; //!< [16] ESAI_TCR Transmit Frame Sync Relative Timing.
        unsigned PADC : 1; //!< [17] ESAI_TCR Transmit Zero Padding Control.
        unsigned RESERVED0 : 1; //!< [18] Reserved.
        unsigned TPR : 1; //!< [19] ESAI_TCR Transmit Section Personal Reset.
        unsigned TEIE : 1; //!< [20] ESAI_TCR Transmit Exception Interrupt Enable.
        unsigned TEDIE : 1; //!< [21] ESAI_TCR Transmit Even Slot Data Interrupt Enable.
        unsigned TIE : 1; //!< [22] ESAI_TCR Transmit Interrupt Enable.
        unsigned TLIE : 1; //!< [23] ESAI_TCR Transmit Last Slot Interrupt Enable.
        unsigned RESERVED1 : 8; //!< [31:24] Reserved.
    } B;
} hw_esai_tcr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TCR register
 */
//@{
#define HW_ESAI_TCR_ADDR      (REGS_ESAI_BASE + 0xd4)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TCR           (*(volatile hw_esai_tcr_t *) HW_ESAI_TCR_ADDR)
#define HW_ESAI_TCR_RD()      (HW_ESAI_TCR.U)
#define HW_ESAI_TCR_WR(v)     (HW_ESAI_TCR.U = (v))
#define HW_ESAI_TCR_SET(v)    (HW_ESAI_TCR_WR(HW_ESAI_TCR_RD() |  (v)))
#define HW_ESAI_TCR_CLR(v)    (HW_ESAI_TCR_WR(HW_ESAI_TCR_RD() & ~(v)))
#define HW_ESAI_TCR_TOG(v)    (HW_ESAI_TCR_WR(HW_ESAI_TCR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_TCR bitfields
 */

/*! @name Register ESAI_TCR, field TE0[0] (RW)
 *
 * ESAI_TCR ESAI Transmit 0 Enable. TE0 enables the transfer of data from ESAI_TX0 to the transmit
 * shift register #0. When TE0 is set and a frame sync is detected, the transmit #0 portion of the
 * ESAI is enabled for that frame. When TE0 is cleared, the transmitter #0 is disabled after
 * completing transmission of data currently in the ESAI transmit shift register. The SDO0 output is
 * tri-stated, and any data present in ESAI_TX0 is not transmitted, that is, data can be written to
 * ESAI_TX0 with TE0 cleared, but data is not transferred to the transmit shift register #0. The
 * normal mode transmit enable sequence is to write data to one or more transmit data registers
 * before setting TEx. The normal transmit disable sequence is to clear TEx, TIE and TEIE after TDE
 * equals one. In the network mode, the operation of clearing TE0 and setting it again disables the
 * transmitter #0 after completing transmission of the current data word until the beginning of the
 * next frame. During that time period, the SDO0 pin remains in the high-impedance state.The on-
 * demand mode transmit enable sequence can be the same as the normal mode, or TE0 can be left
 * enabled.
 */
//@{
#define BP_ESAI_TCR_TE0      (0)      //!< Bit position for ESAI_TCR_TE0.
#define BM_ESAI_TCR_TE0      (0x00000001)  //!< Bit mask for ESAI_TCR_TE0.

//! @brief Get value of ESAI_TCR_TE0 from a register value.
#define BG_ESAI_TCR_TE0(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TE0) >> BP_ESAI_TCR_TE0)

//! @brief Format value for bitfield ESAI_TCR_TE0.
#define BF_ESAI_TCR_TE0(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TE0) & BM_ESAI_TCR_TE0)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE0 field to a new value.
#define BW_ESAI_TCR_TE0(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TE0) | BF_ESAI_TCR_TE0(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TE1[1] (RW)
 *
 * ESAI_TCR ESAI Transmit 1 Enable. TE1 enables the transfer of data from TX1 to the transmit shift
 * register #1. When TE1 is set and a frame sync is detected, the transmit #1 portion of the ESAI is
 * enabled for that frame. When TE1 is cleared, the transmitter #1 is disabled after completing
 * transmission of data currently in the ESAI transmit shift register. The SDO1 output is tri-
 * stated, and any data present in TX1 is not transmitted, that is, data can be written to TX1 with
 * TE1 cleared, but data is not transferred to the transmit shift register #1. The normal mode
 * transmit enable sequence is to write data to one or more transmit data registers before setting
 * TEx. The normal transmit disable sequence is to clear TEx, TIE and TEIE after TDE equals one. In
 * the network mode, the operation of clearing TE1 and setting it again disables the transmitter #1
 * after completing transmission of the current data word until the beginning of the next frame.
 * During that time period, the SDO1 pin remains in the high-impedance state. The on-demand mode
 * transmit enable sequence can be the same as the normal mode, or TE1 can be left enabled.
 */
//@{
#define BP_ESAI_TCR_TE1      (1)      //!< Bit position for ESAI_TCR_TE1.
#define BM_ESAI_TCR_TE1      (0x00000002)  //!< Bit mask for ESAI_TCR_TE1.

//! @brief Get value of ESAI_TCR_TE1 from a register value.
#define BG_ESAI_TCR_TE1(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TE1) >> BP_ESAI_TCR_TE1)

//! @brief Format value for bitfield ESAI_TCR_TE1.
#define BF_ESAI_TCR_TE1(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TE1) & BM_ESAI_TCR_TE1)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE1 field to a new value.
#define BW_ESAI_TCR_TE1(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TE1) | BF_ESAI_TCR_TE1(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TE2[2] (RW)
 *
 * ESAI_TCR ESAI Transmit 2 Enable. TE2 enables the transfer of data from ESAI_TX2 to the transmit
 * shift register #2. When TE2 is set and a frame sync is detected, the transmit #2 portion of the
 * ESAI is enabled for that frame. When TE2 is cleared, the transmitter #2 is disabled after
 * completing transmission of data currently in the ESAI transmit shift register. Data can be
 * written to ESAI_TX2 when TE2 is cleared but the data is not transferred to the transmit shift
 * register #2. The SDO2/SDI3 pin is the data input pin for ESAI_RX3 if TE2 is cleared and RE3 in
 * the ESAI_RCR register is set. If both RE3 and TE2 are cleared, the transmitter and receiver are
 * disabled, and the pin is tri-stated. Both RE3 and TE2 should not be set at the same time. The
 * normal mode transmit enable sequence is to write data to one or more transmit data registers
 * before setting TEx. The normal transmit disable sequence is to clear TEx, TIE and TEIE after TDE
 * equals one. In the network mode, the operation of clearing TE2 and setting it again disables the
 * transmitter #2 after completing transmission of the current data word until the beginning of the
 * next frame. During that time period, the SDO2/SDI3 pin remains in the high-impedance state. The
 * on-demand mode transmit enable sequence can be the same as the normal mode, or TE2 can be left
 * enabled.
 */
//@{
#define BP_ESAI_TCR_TE2      (2)      //!< Bit position for ESAI_TCR_TE2.
#define BM_ESAI_TCR_TE2      (0x00000004)  //!< Bit mask for ESAI_TCR_TE2.

//! @brief Get value of ESAI_TCR_TE2 from a register value.
#define BG_ESAI_TCR_TE2(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TE2) >> BP_ESAI_TCR_TE2)

//! @brief Format value for bitfield ESAI_TCR_TE2.
#define BF_ESAI_TCR_TE2(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TE2) & BM_ESAI_TCR_TE2)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE2 field to a new value.
#define BW_ESAI_TCR_TE2(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TE2) | BF_ESAI_TCR_TE2(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TE3[3] (RW)
 *
 * ESAI_TCR ESAI Transmit 3 Enable. TE3 enables the transfer of data from ESAI_TX3 to the transmit
 * shift register #3. When TE3 is set and a frame sync is detected, the transmit #3 portion of the
 * ESAI is enabled for that frame. When TE3 is cleared, the transmitter #3 is disabled after
 * completing transmission of data currently in the ESAI transmit shift register. Data can be
 * written to ESAI_TX3 when TE3 is cleared but the data is not transferred to the transmit shift
 * register #3. The SDO3/SDI2 pin is the data input pin for ESAI_RX2 if TE3 is cleared and RE2 in
 * the ESAI_RCR register is set. If both RE2 and TE3 are cleared, the transmitter and receiver are
 * disabled, and the pin is tri-stated. Both RE2 and TE3 should not be set at the same time. The
 * normal mode transmit enable sequence is to write data to one or more transmit data registers
 * before setting TEx. The normal transmit disable sequence is to clear TEx, TIE and TEIE after TDE
 * equals one. In the network mode, the operation of clearing TE3 and setting it again disables the
 * transmitter #3 after completing transmission of the current data word until the beginning of the
 * next frame. During that time period, the SDO3/SDI2 pin remains in the high-impedance state. The
 * on-demand mode transmit enable sequence can be the same as the normal mode, or TE3 can be left
 * enabled.
 */
//@{
#define BP_ESAI_TCR_TE3      (3)      //!< Bit position for ESAI_TCR_TE3.
#define BM_ESAI_TCR_TE3      (0x00000008)  //!< Bit mask for ESAI_TCR_TE3.

//! @brief Get value of ESAI_TCR_TE3 from a register value.
#define BG_ESAI_TCR_TE3(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TE3) >> BP_ESAI_TCR_TE3)

//! @brief Format value for bitfield ESAI_TCR_TE3.
#define BF_ESAI_TCR_TE3(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TE3) & BM_ESAI_TCR_TE3)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE3 field to a new value.
#define BW_ESAI_TCR_TE3(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TE3) | BF_ESAI_TCR_TE3(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TE4[4] (RW)
 *
 * ESAI_TCR ESAI Transmit 4 Enable. TE4 enables the transfer of data from ESAI_TX4 to the transmit
 * shift register #4. When TE4 is set and a frame sync is detected, the transmit #4 portion of the
 * ESAI is enabled for that frame. When TE4 is cleared, the transmitter #4 is disabled after
 * completing transmission of data currently in the ESAI transmit shift register. Data can be
 * written to ESAI_TX4 when TE4 is cleared but the data is not transferred to the transmit shift
 * register #4. The SDO4/SDI1 pin is the data input pin for ESAI_RX1 if TE4 is cleared and RE1 in
 * the RCR register is set. If both RE1 and TE4 are cleared, the transmitter and receiver are
 * disabled, and the pin is tri-stated. Both RE1 and TE4 should not be set at the same time. The
 * normal mode transmit enable sequence is to write data to one or more transmit data registers
 * before setting TEx. The normal transmit disable sequence is to clear TEx, TIE and TEIE after TDE
 * equals one. In the network mode, the operation of clearing TE4 and setting it again disables the
 * transmitter #4 after completing transmission of the current data word until the beginning of the
 * next frame. During that time period, the SDO4/SDI1 pin remains in the high-impedance state. The
 * on-demand mode transmit enable sequence can be the same as the normal mode, or TE4 can be left
 * enabled.
 */
//@{
#define BP_ESAI_TCR_TE4      (4)      //!< Bit position for ESAI_TCR_TE4.
#define BM_ESAI_TCR_TE4      (0x00000010)  //!< Bit mask for ESAI_TCR_TE4.

//! @brief Get value of ESAI_TCR_TE4 from a register value.
#define BG_ESAI_TCR_TE4(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TE4) >> BP_ESAI_TCR_TE4)

//! @brief Format value for bitfield ESAI_TCR_TE4.
#define BF_ESAI_TCR_TE4(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TE4) & BM_ESAI_TCR_TE4)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE4 field to a new value.
#define BW_ESAI_TCR_TE4(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TE4) | BF_ESAI_TCR_TE4(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TE5[5] (RW)
 *
 * ESAI_TCR ESAI Transmit 5 Enable. TE5 enables the transfer of data from ESAI_TX5 to the transmit
 * shift register #5. When TE5 is set and a frame sync is detected, the transmit #5 portion of the
 * ESAI is enabled for that frame. When TE5 is cleared, the transmitter #5 is disabled after
 * completing transmission of data currently in the ESAI transmit shift register. Data can be
 * written to ESAI_TX5 when TE5 is cleared but the data is not transferred to the transmit shift
 * register #5. The SDO5/SDI0 pin is the data input pin for ESAI_RX0 if TE5 is cleared and RE0 in
 * the ESAI_RCR register is set. If both RE0 and TE5 are cleared, the transmitter and receiver are
 * disabled, and the pin is tri-stated. Both RE0 and TE5 should not be set at the same time. The
 * normal mode transmit enable sequence is to write data to one or more transmit data registers
 * before setting TEx. The normal transmit disable sequence is to clear TEx, TIE and TEIE after TDE
 * equals one. In the network mode, the operation of clearing TE5 and setting it again disables the
 * transmitter #5 after completing transmission of the current data word until the beginning of the
 * next frame. During that time period, the SDO5/SDI0 pin remains in the high-impedance state. The
 * on-demand mode transmit enable sequence can be the same as the normal mode, or TE5 can be left
 * enabled.
 */
//@{
#define BP_ESAI_TCR_TE5      (5)      //!< Bit position for ESAI_TCR_TE5.
#define BM_ESAI_TCR_TE5      (0x00000020)  //!< Bit mask for ESAI_TCR_TE5.

//! @brief Get value of ESAI_TCR_TE5 from a register value.
#define BG_ESAI_TCR_TE5(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TE5) >> BP_ESAI_TCR_TE5)

//! @brief Format value for bitfield ESAI_TCR_TE5.
#define BF_ESAI_TCR_TE5(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TE5) & BM_ESAI_TCR_TE5)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TE5 field to a new value.
#define BW_ESAI_TCR_TE5(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TE5) | BF_ESAI_TCR_TE5(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TSHFD[6] (RW)
 *
 * ESAI_TCR Transmit Shift Direction. The TSHFD bit causes the transmit shift registers to shift
 * data out MSB first when TSHFD equals zero or LSB first when TSHFD equals one (see and .
 */
//@{
#define BP_ESAI_TCR_TSHFD      (6)      //!< Bit position for ESAI_TCR_TSHFD.
#define BM_ESAI_TCR_TSHFD      (0x00000040)  //!< Bit mask for ESAI_TCR_TSHFD.

//! @brief Get value of ESAI_TCR_TSHFD from a register value.
#define BG_ESAI_TCR_TSHFD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TSHFD) >> BP_ESAI_TCR_TSHFD)

//! @brief Format value for bitfield ESAI_TCR_TSHFD.
#define BF_ESAI_TCR_TSHFD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TSHFD) & BM_ESAI_TCR_TSHFD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TSHFD field to a new value.
#define BW_ESAI_TCR_TSHFD(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TSHFD) | BF_ESAI_TCR_TSHFD(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TWA[7] (RW)
 *
 * ESAI_TCR Transmit Word Alignment Control. The Transmitter Word Alignment Control (TWA) bit
 * defines the alignment of the data word in relation to the slot. This is relevant for the cases
 * where the word length is shorter than the slot length. If TWA is cleared, the data word is left-
 * aligned in the slot frame during transmission. If TWA is set, the data word is right-aligned in
 * the slot frame during transmission. Because the data word is shorter than the slot length, the
 * data word is extended until achieving the slot length, according to the following rule: If the
 * data word is left-aligned (TWA=0), and zero padding is disabled (PADC=0), the last data bit is
 * repeated after the data word has been transmitted. If zero padding is enabled (PADC=1), zeroes
 * are transmitted after the data word has been transmitted. If the data word is right-aligned
 * (TWA=1), and zero padding is disabled (PADC=0), the first data bit is repeated before the
 * transmission of the data word. If zero padding is enabled (PADC=1), zeroes are transmitted before
 * the transmission of the data word.
 */
//@{
#define BP_ESAI_TCR_TWA      (7)      //!< Bit position for ESAI_TCR_TWA.
#define BM_ESAI_TCR_TWA      (0x00000080)  //!< Bit mask for ESAI_TCR_TWA.

//! @brief Get value of ESAI_TCR_TWA from a register value.
#define BG_ESAI_TCR_TWA(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TWA) >> BP_ESAI_TCR_TWA)

//! @brief Format value for bitfield ESAI_TCR_TWA.
#define BF_ESAI_TCR_TWA(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TWA) & BM_ESAI_TCR_TWA)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TWA field to a new value.
#define BW_ESAI_TCR_TWA(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TWA) | BF_ESAI_TCR_TWA(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TMOD[9:8] (RW)
 *
 * ESAI_TCR Transmit Network Mode Control (TMOD1-TMOD0). The TMOD1 and TMOD0 bits are used to define
 * the network mode of ESAI transmitters, as shown in Port C Control Register . In the normal mode,
 * the frame rate divider determines the word transfer rate - one word is transferred per frame sync
 * during the frame sync time slot, as shown in . In network mode, it is possible to transfer a word
 * for every time slot, as shown in . For further details, refer to In order to comply with AC-97
 * specifications, TSWS4-TSWS0 should be set to 00011 (20-bit slot, 20-bit word length), TFSL and
 * TFSR should be cleared, and TDC4-TDC0 should be set to 0x0C (13 words in frame). If
 * TMOD[1:0]=0b11 and the above recommendations are followed, the first slot and word will be 16
 * bits long, and the next 12 slots and words will be 20 bits long, as required by the AC97
 * protocol.
 */
//@{
#define BP_ESAI_TCR_TMOD      (8)      //!< Bit position for ESAI_TCR_TMOD.
#define BM_ESAI_TCR_TMOD      (0x00000300)  //!< Bit mask for ESAI_TCR_TMOD.

//! @brief Get value of ESAI_TCR_TMOD from a register value.
#define BG_ESAI_TCR_TMOD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TMOD) >> BP_ESAI_TCR_TMOD)

//! @brief Format value for bitfield ESAI_TCR_TMOD.
#define BF_ESAI_TCR_TMOD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TMOD) & BM_ESAI_TCR_TMOD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TMOD field to a new value.
#define BW_ESAI_TCR_TMOD(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TMOD) | BF_ESAI_TCR_TMOD(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TSWS[14:10] (RW)
 *
 * ESAI_TCR Tx Slot and Word Length Select (TSWS4-TSWS0). The TSWS4-TSWS0 bits are used to select
 * the length of the slot and the length of the data words being transferred through the ESAI. The
 * word length must be equal to or shorter than the slot length. The possible combinations are shown
 * in . See also the ESAI data path programming model in and .
 */
//@{
#define BP_ESAI_TCR_TSWS      (10)      //!< Bit position for ESAI_TCR_TSWS.
#define BM_ESAI_TCR_TSWS      (0x00007c00)  //!< Bit mask for ESAI_TCR_TSWS.

//! @brief Get value of ESAI_TCR_TSWS from a register value.
#define BG_ESAI_TCR_TSWS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TSWS) >> BP_ESAI_TCR_TSWS)

//! @brief Format value for bitfield ESAI_TCR_TSWS.
#define BF_ESAI_TCR_TSWS(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TSWS) & BM_ESAI_TCR_TSWS)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TSWS field to a new value.
#define BW_ESAI_TCR_TSWS(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TSWS) | BF_ESAI_TCR_TSWS(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TFSL[15] (RW)
 *
 * ESAI_TCR Transmit Frame Sync Length. The TFSL bit selects the length of frame sync to be
 * generated or recognized. If TFSL is cleared, a word-length frame sync is selected. If TFSL is
 * set, a 1-bit clock period frame sync is selected. See Figure 1-21 for examples of frame length
 * selection.
 */
//@{
#define BP_ESAI_TCR_TFSL      (15)      //!< Bit position for ESAI_TCR_TFSL.
#define BM_ESAI_TCR_TFSL      (0x00008000)  //!< Bit mask for ESAI_TCR_TFSL.

//! @brief Get value of ESAI_TCR_TFSL from a register value.
#define BG_ESAI_TCR_TFSL(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TFSL) >> BP_ESAI_TCR_TFSL)

//! @brief Format value for bitfield ESAI_TCR_TFSL.
#define BF_ESAI_TCR_TFSL(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TFSL) & BM_ESAI_TCR_TFSL)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFSL field to a new value.
#define BW_ESAI_TCR_TFSL(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TFSL) | BF_ESAI_TCR_TFSL(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TFSR[16] (RW)
 *
 * ESAI_TCR Transmit Frame Sync Relative Timing. TFSR determines the relative timing of the transmit
 * frame sync signal as referred to the serial data lines, for a word length frame sync only
 * (TFSL=0). When TFSR is cleared the word length frame sync occurs together with the first bit of
 * the data word of the first slot. When TFSR is set the word length frame sync starts one serial
 * clock cycle earlier, that is, together with the last bit of the previous data word.
 */
//@{
#define BP_ESAI_TCR_TFSR      (16)      //!< Bit position for ESAI_TCR_TFSR.
#define BM_ESAI_TCR_TFSR      (0x00010000)  //!< Bit mask for ESAI_TCR_TFSR.

//! @brief Get value of ESAI_TCR_TFSR from a register value.
#define BG_ESAI_TCR_TFSR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TFSR) >> BP_ESAI_TCR_TFSR)

//! @brief Format value for bitfield ESAI_TCR_TFSR.
#define BF_ESAI_TCR_TFSR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TFSR) & BM_ESAI_TCR_TFSR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFSR field to a new value.
#define BW_ESAI_TCR_TFSR(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TFSR) | BF_ESAI_TCR_TFSR(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field PADC[17] (RW)
 *
 * ESAI_TCR Transmit Zero Padding Control. When PADC is cleared, zero padding is disabled. When PADC
 * is set, zero padding is enabled. PADC, in conjunction with the TWA control bit, determines the
 * way that padding is done for operating modes where the word length is less than the slot length.
 * See the TWA bit description in bit 7 for more details. Because the data word is shorter than the
 * slot length, the data word is extended until achieving the slot length, according to the
 * following rule: If the data word is left-aligned (TWA=0), and zero padding is disabled (PADC=0),
 * the last data bit is repeated after the data word has been transmitted. If zero padding is
 * enabled (PADC=1), zeroes are transmitted after the data word has been transmitted. If the data
 * word is right-aligned (TWA=1), and zero padding is disabled (PADC=0), the first data bit is
 * repeated before the transmission of the data word. If zero padding is enabled (PADC=1), zeroes
 * are transmitted before the transmission of the data word.
 */
//@{
#define BP_ESAI_TCR_PADC      (17)      //!< Bit position for ESAI_TCR_PADC.
#define BM_ESAI_TCR_PADC      (0x00020000)  //!< Bit mask for ESAI_TCR_PADC.

//! @brief Get value of ESAI_TCR_PADC from a register value.
#define BG_ESAI_TCR_PADC(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_PADC) >> BP_ESAI_TCR_PADC)

//! @brief Format value for bitfield ESAI_TCR_PADC.
#define BF_ESAI_TCR_PADC(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_PADC) & BM_ESAI_TCR_PADC)

#ifndef __LANGUAGE_ASM__
//! @brief Set the PADC field to a new value.
#define BW_ESAI_TCR_PADC(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_PADC) | BF_ESAI_TCR_PADC(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TPR[19] (RW)
 *
 * ESAI_TCR Transmit Section Personal Reset. The TPR control bit is used to put the transmitter
 * section of the ESAI in the personal reset state. The receiver section is not affected. When TPR
 * is cleared, the transmitter section may operate normally. When TPR is set, the transmitter
 * section enters the personal reset state immediately. When in the personal reset state, the status
 * bits are reset to the same state as after hardware reset. The control bits are not affected by
 * the personal reset state. The transmitter data pins are tri-stated while in the personal reset
 * state; if a stable logic level is desired, the transmitter data pins should be defined as GPIO
 * outputs, or external pull-up or pull-down resistors should be used. The transmitter clock outputs
 * drive zeroes while in the personal reset state. Note that to leave the personal reset state by
 * clearing TPR, the procedure described in should be followed.
 */
//@{
#define BP_ESAI_TCR_TPR      (19)      //!< Bit position for ESAI_TCR_TPR.
#define BM_ESAI_TCR_TPR      (0x00080000)  //!< Bit mask for ESAI_TCR_TPR.

//! @brief Get value of ESAI_TCR_TPR from a register value.
#define BG_ESAI_TCR_TPR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TPR) >> BP_ESAI_TCR_TPR)

//! @brief Format value for bitfield ESAI_TCR_TPR.
#define BF_ESAI_TCR_TPR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TPR) & BM_ESAI_TCR_TPR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TPR field to a new value.
#define BW_ESAI_TCR_TPR(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TPR) | BF_ESAI_TCR_TPR(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TEIE[20] (RW)
 *
 * ESAI_TCR Transmit Exception Interrupt Enable. When TEIE is set, the Core is interrupted when both
 * TDE and TUE in the ESAI_SAISR status register are set. When TEIE is cleared, this interrupt is
 * disabled. Reading the ESAI_SAISR status register followed by writing to all the data registers of
 * the enabled transmitters clears TUE, thus clearing the pending interrupt.
 */
//@{
#define BP_ESAI_TCR_TEIE      (20)      //!< Bit position for ESAI_TCR_TEIE.
#define BM_ESAI_TCR_TEIE      (0x00100000)  //!< Bit mask for ESAI_TCR_TEIE.

//! @brief Get value of ESAI_TCR_TEIE from a register value.
#define BG_ESAI_TCR_TEIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TEIE) >> BP_ESAI_TCR_TEIE)

//! @brief Format value for bitfield ESAI_TCR_TEIE.
#define BF_ESAI_TCR_TEIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TEIE) & BM_ESAI_TCR_TEIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TEIE field to a new value.
#define BW_ESAI_TCR_TEIE(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TEIE) | BF_ESAI_TCR_TEIE(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TEDIE[21] (RW)
 *
 * ESAI_TCR Transmit Even Slot Data Interrupt Enable. The TEDIE control bit is used to enable the
 * transmit even slot data interrupts. If TEDIE is set, the transmit even slot data interrupts are
 * enabled. If TEDIE is cleared, the transmit even slot data interrupts are disabled. A transmit
 * even slot data interrupt request is generated if TEDIE is set and the TEDE status flag in the
 * ESAI_SAISR status register is set. Even time slots are all even-numbered time slots (0, 2, 4,
 * etc.) when operating in network mode. The zero time slot in the frame is marked by the frame sync
 * signal and is considered to be even. Writing data to all the data registers of the enabled
 * transmitters or to ESAI_TSR clears the TEDE flag, thus servicing the interrupt. Transmit
 * interrupts with exception have higher priority than transmit even slot data interrupts, therefore
 * if exception occurs (TUE is set) and TEIE is set, the ESAI requests an ESAI transmit data with
 * exception interrupt from the interrupt controller.
 */
//@{
#define BP_ESAI_TCR_TEDIE      (21)      //!< Bit position for ESAI_TCR_TEDIE.
#define BM_ESAI_TCR_TEDIE      (0x00200000)  //!< Bit mask for ESAI_TCR_TEDIE.

//! @brief Get value of ESAI_TCR_TEDIE from a register value.
#define BG_ESAI_TCR_TEDIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TEDIE) >> BP_ESAI_TCR_TEDIE)

//! @brief Format value for bitfield ESAI_TCR_TEDIE.
#define BF_ESAI_TCR_TEDIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TEDIE) & BM_ESAI_TCR_TEDIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TEDIE field to a new value.
#define BW_ESAI_TCR_TEDIE(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TEDIE) | BF_ESAI_TCR_TEDIE(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TIE[22] (RW)
 *
 * ESAI_TCR Transmit Interrupt Enable. The Core is interrupted when TIE and the TDE flag in the
 * ESAI_SAISR status register are set. When TIE is cleared, this interrupt is disabled. Writing data
 * to all the data registers of the enabled transmitters or to ESAI_TSR clears TDE, thus clearing
 * the interrupt. Transmit interrupts with exception have higher priority than normal transmit data
 * interrupts, therefore if exception occurs (TUE is set) and TEIE is set, the ESAI requests an ESAI
 * transmit data with exception interrupt from the interrupt controller.
 */
//@{
#define BP_ESAI_TCR_TIE      (22)      //!< Bit position for ESAI_TCR_TIE.
#define BM_ESAI_TCR_TIE      (0x00400000)  //!< Bit mask for ESAI_TCR_TIE.

//! @brief Get value of ESAI_TCR_TIE from a register value.
#define BG_ESAI_TCR_TIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TIE) >> BP_ESAI_TCR_TIE)

//! @brief Format value for bitfield ESAI_TCR_TIE.
#define BF_ESAI_TCR_TIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TIE) & BM_ESAI_TCR_TIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TIE field to a new value.
#define BW_ESAI_TCR_TIE(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TIE) | BF_ESAI_TCR_TIE(v)))
#endif
//@}

/*! @name Register ESAI_TCR, field TLIE[23] (RW)
 *
 * ESAI_TCR Transmit Last Slot Interrupt Enable. TLIE enables an interrupt at the beginning of last
 * slot of a frame in network mode. When TLIE is set the Core is interrupted at the start of the
 * last slot in a frame in network mode regardless of the transmit mask register setting. When TLIE
 * is cleared the transmit last slot interrupt is disabled. TLIE is disabled when TDC[4:0]=0x00000
 * (on-demand mode). The use of the transmit last slot interrupt is described in .
 */
//@{
#define BP_ESAI_TCR_TLIE      (23)      //!< Bit position for ESAI_TCR_TLIE.
#define BM_ESAI_TCR_TLIE      (0x00800000)  //!< Bit mask for ESAI_TCR_TLIE.

//! @brief Get value of ESAI_TCR_TLIE from a register value.
#define BG_ESAI_TCR_TLIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCR_TLIE) >> BP_ESAI_TCR_TLIE)

//! @brief Format value for bitfield ESAI_TCR_TLIE.
#define BF_ESAI_TCR_TLIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCR_TLIE) & BM_ESAI_TCR_TLIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TLIE field to a new value.
#define BW_ESAI_TCR_TLIE(v)   (HW_ESAI_TCR_WR((HW_ESAI_TCR_RD() & ~BM_ESAI_TCR_TLIE) | BF_ESAI_TCR_TLIE(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TCCR - Transmit Clock Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TCCR - Transmit Clock Control Register (RW)
 *
 * Reset value: 0x00000000
 *
 * The read/write Transmitter Clock Control Register (ESAI_TCCR) controls the ESAI transmitter clock
 * generator bit and frame sync rates, the bit clock and high frequency clock sources and the
 * directions of the HCKT, FST and SCKT signals. In the synchronous mode (SYN=1), the bit clock
 * defined for the transmitter determines the receiver bit clock as well. ESAI_TCCR also controls
 * the number of words per frame for the serial data. Hardware and software reset clear all the bits
 * of the ESAI_TCCR register. Care should be taken in asynchronous mode whenever the frame sync
 * clock (FSR, FST) is not sourced directly from its associated bit clock (SCKR, SCKT). Proper phase
 * relationships must be maintained between these clocks in order to guarantee proper operation of
 * the ESAI. ARM Core clock is ipg_clk_esai in block ESAI which is from CCM's ahb_clk_root. ESAI
 * Clock Generator Functional Block Diagram 1. ETI, ETO, ERI and ERO bit descriptions are covered in
 * . 2. Fsys is the ESAI system 133 MHz clock. 3. EXTAL is the on-chip clock sources other than ESAI
 * system 133MHz clock. ESAI Frame Sync Generator Functional Block Diagram Transmitter High
 * Frequency Clock Divider TFP3-TFP0 Divide Ratio 0x0 1 0x1 2 0x2 3 0x3 4 ... ... 0xF 16
 */
typedef union _hw_esai_tccr
{
    reg32_t U;
    struct _hw_esai_tccr_bitfields
    {
        unsigned TPM : 8; //!< [7:0] ESAI_TCCR Transmit Prescale Modulus Select.
        unsigned TPSR : 1; //!< [8] ESAI_TCCR Transmit Prescaler Range.
        unsigned TDC : 5; //!< [13:9] ESAI_TCCR Tx Frame Rate Divider Control.
        unsigned TFP : 4; //!< [17:14] ESAI_TCCR Tx High Frequency Clock Divider.
        unsigned TCKP : 1; //!< [18] ESAI_TCCR Transmit Clock Polarity.
        unsigned TFSP : 1; //!< [19] ESAI_TCCR Transmit Frame Sync Polarity.
        unsigned THCKP : 1; //!< [20] ESAI_TCCR Transmit High Frequency Clock Polarity.
        unsigned TCKD : 1; //!< [21] ESAI_TCCR Transmit Clock Source Direction.
        unsigned TFSD : 1; //!< [22] ESAI_TCCR Transmit Frame Sync Signal Direction.
        unsigned THCKD : 1; //!< [23] ESAI_TCCR Transmit High Frequency Clock Direction.
        unsigned RESERVED0 : 8; //!< [31:24] Reserved.
    } B;
} hw_esai_tccr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TCCR register
 */
//@{
#define HW_ESAI_TCCR_ADDR      (REGS_ESAI_BASE + 0xd8)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TCCR           (*(volatile hw_esai_tccr_t *) HW_ESAI_TCCR_ADDR)
#define HW_ESAI_TCCR_RD()      (HW_ESAI_TCCR.U)
#define HW_ESAI_TCCR_WR(v)     (HW_ESAI_TCCR.U = (v))
#define HW_ESAI_TCCR_SET(v)    (HW_ESAI_TCCR_WR(HW_ESAI_TCCR_RD() |  (v)))
#define HW_ESAI_TCCR_CLR(v)    (HW_ESAI_TCCR_WR(HW_ESAI_TCCR_RD() & ~(v)))
#define HW_ESAI_TCCR_TOG(v)    (HW_ESAI_TCCR_WR(HW_ESAI_TCCR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_TCCR bitfields
 */

/*! @name Register ESAI_TCCR, field TPM[7:0] (RW)
 *
 * ESAI_TCCR Transmit Prescale Modulus Select. The TPM7-TPM0 bits specify the divide ratio of the
 * prescale divider in the ESAI transmitter clock generator. A divide ratio from 1 to 256
 * (TPM[7:0]=0x00 to 0xFF) may be selected. The bit clock output is available at the transmit serial
 * bit clock (SCKT) pin. The bit clock output is also available internally for use as the bit clock
 * to shift the transmit and receive shift registers. The ESAI transmit clock generator functional
 * diagram is shown in .
 */
//@{
#define BP_ESAI_TCCR_TPM      (0)      //!< Bit position for ESAI_TCCR_TPM.
#define BM_ESAI_TCCR_TPM      (0x000000ff)  //!< Bit mask for ESAI_TCCR_TPM.

//! @brief Get value of ESAI_TCCR_TPM from a register value.
#define BG_ESAI_TCCR_TPM(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TPM) >> BP_ESAI_TCCR_TPM)

//! @brief Format value for bitfield ESAI_TCCR_TPM.
#define BF_ESAI_TCCR_TPM(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TPM) & BM_ESAI_TCCR_TPM)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TPM field to a new value.
#define BW_ESAI_TCCR_TPM(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TPM) | BF_ESAI_TCCR_TPM(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TPSR[8] (RW)
 *
 * ESAI_TCCR Transmit Prescaler Range. The TPSR bit controls a fixed divide-by-eight prescaler in
 * series with the variable prescaler. This bit is used to extend the range of the prescaler for
 * those cases where a slower bit clock is desired. When TPSR is set, the fixed prescaler is
 * bypassed. When TPSR is cleared, the fixed divide-by-eight prescaler is operational (see ). The
 * maximum internally generated bit clock frequency is Fsys/4; the minimum internally generated bit
 * clock frequency is Fsys/(2 x 8 x 256 x 16)=Fsys/65536. (Do not use the combination TPSR=1,
 * TPM7-TPM0=0x00, and TFP3-TFP0=0x0 which causes synchronization problems when using the internal
 * ARM Core clock as source (TCKD=1 or THCKD=1))
 */
//@{
#define BP_ESAI_TCCR_TPSR      (8)      //!< Bit position for ESAI_TCCR_TPSR.
#define BM_ESAI_TCCR_TPSR      (0x00000100)  //!< Bit mask for ESAI_TCCR_TPSR.

//! @brief Get value of ESAI_TCCR_TPSR from a register value.
#define BG_ESAI_TCCR_TPSR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TPSR) >> BP_ESAI_TCCR_TPSR)

//! @brief Format value for bitfield ESAI_TCCR_TPSR.
#define BF_ESAI_TCCR_TPSR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TPSR) & BM_ESAI_TCCR_TPSR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TPSR field to a new value.
#define BW_ESAI_TCCR_TPSR(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TPSR) | BF_ESAI_TCCR_TPSR(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TDC[13:9] (RW)
 *
 * ESAI_TCCR Tx Frame Rate Divider Control. The TDC4-TDC0 bits control the divide ratio for the
 * programmable frame rate dividers used to generate the transmitter frame clocks. In network mode,
 * this ratio may be interpreted as the number of words per frame minus one. The divide ratio may
 * range from 2 to 32 (TDC[4:0]=0x00001 to 0x11111) for network mode. A divide ratio of one
 * (TDC[4:0]=0x00000) in network mode is a special case (on-demand mode). In normal mode, this ratio
 * determines the word transfer rate. The divide ratio may range from 1 to 32 (TDC[4:0]=0x00000 to
 * 0x11111) for normal mode. In normal mode, a divide ratio of 1 (TDC[4:0]=0x00000) provides
 * continuous periodic data word transfers. A bit-length frame sync (TFSL=1) must be used in this
 * case. The ESAI frame sync generator functional diagram is shown in
 */
//@{
#define BP_ESAI_TCCR_TDC      (9)      //!< Bit position for ESAI_TCCR_TDC.
#define BM_ESAI_TCCR_TDC      (0x00003e00)  //!< Bit mask for ESAI_TCCR_TDC.

//! @brief Get value of ESAI_TCCR_TDC from a register value.
#define BG_ESAI_TCCR_TDC(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TDC) >> BP_ESAI_TCCR_TDC)

//! @brief Format value for bitfield ESAI_TCCR_TDC.
#define BF_ESAI_TCCR_TDC(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TDC) & BM_ESAI_TCCR_TDC)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TDC field to a new value.
#define BW_ESAI_TCCR_TDC(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TDC) | BF_ESAI_TCCR_TDC(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TFP[17:14] (RW)
 *
 * ESAI_TCCR Tx High Frequency Clock Divider. The TFP3-TFP0 bits control the divide ratio of the
 * transmitter high frequency clock to the transmitter serial bit clock when the source of the high
 * frequency clock and the bit clock is the internal ARM Core clock. When the HCKT input is being
 * driven from an external high frequency clock, the TFP3-TFP0 bits specify an additional division
 * ratio in the clock divider chain. shows the specification for the divide ratio. shows the ESAI
 * high frequency clock generator functional diagram.
 */
//@{
#define BP_ESAI_TCCR_TFP      (14)      //!< Bit position for ESAI_TCCR_TFP.
#define BM_ESAI_TCCR_TFP      (0x0003c000)  //!< Bit mask for ESAI_TCCR_TFP.

//! @brief Get value of ESAI_TCCR_TFP from a register value.
#define BG_ESAI_TCCR_TFP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TFP) >> BP_ESAI_TCCR_TFP)

//! @brief Format value for bitfield ESAI_TCCR_TFP.
#define BF_ESAI_TCCR_TFP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TFP) & BM_ESAI_TCCR_TFP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFP field to a new value.
#define BW_ESAI_TCCR_TFP(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TFP) | BF_ESAI_TCCR_TFP(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TCKP[18] (RW)
 *
 * ESAI_TCCR Transmit Clock Polarity. The Transmitter Clock Polarity (TCKP) bit controls on which
 * bit clock edge data and frame sync are clocked out and latched in. If TCKP is cleared the data
 * and the frame sync are clocked out on the rising edge of the transmit bit clock and latched in on
 * the falling edge of the transmit bit clock. If TCKP is set the falling edge of the transmit clock
 * is used to clock the data out and frame sync and the rising edge of the transmit clock is used to
 * latch the data and frame sync in.
 */
//@{
#define BP_ESAI_TCCR_TCKP      (18)      //!< Bit position for ESAI_TCCR_TCKP.
#define BM_ESAI_TCCR_TCKP      (0x00040000)  //!< Bit mask for ESAI_TCCR_TCKP.

//! @brief Get value of ESAI_TCCR_TCKP from a register value.
#define BG_ESAI_TCCR_TCKP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TCKP) >> BP_ESAI_TCCR_TCKP)

//! @brief Format value for bitfield ESAI_TCCR_TCKP.
#define BF_ESAI_TCCR_TCKP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TCKP) & BM_ESAI_TCCR_TCKP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TCKP field to a new value.
#define BW_ESAI_TCCR_TCKP(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TCKP) | BF_ESAI_TCCR_TCKP(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TFSP[19] (RW)
 *
 * ESAI_TCCR Transmit Frame Sync Polarity. The Transmitter Frame Sync Polarity (TFSP) bit determines
 * the polarity of the transmit frame sync signal. When TFSP is cleared, the frame sync signal
 * polarity is positive, that is, the frame start is indicated by a high level on the frame sync
 * pin. When TFSP is set, the frame sync signal polarity is negative, that is, the frame start is
 * indicated by a low level on the frame sync pin.
 */
//@{
#define BP_ESAI_TCCR_TFSP      (19)      //!< Bit position for ESAI_TCCR_TFSP.
#define BM_ESAI_TCCR_TFSP      (0x00080000)  //!< Bit mask for ESAI_TCCR_TFSP.

//! @brief Get value of ESAI_TCCR_TFSP from a register value.
#define BG_ESAI_TCCR_TFSP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TFSP) >> BP_ESAI_TCCR_TFSP)

//! @brief Format value for bitfield ESAI_TCCR_TFSP.
#define BF_ESAI_TCCR_TFSP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TFSP) & BM_ESAI_TCCR_TFSP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFSP field to a new value.
#define BW_ESAI_TCCR_TFSP(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TFSP) | BF_ESAI_TCCR_TFSP(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field THCKP[20] (RW)
 *
 * ESAI_TCCR Transmit High Frequency Clock Polarity. The Transmitter High Frequency Clock Polarity
 * (THCKP) bit controls on which bit clock edge data and frame sync are clocked out and latched in.
 * If THCKP is cleared the data and the frame sync are clocked out on the rising edge of the
 * transmit high frequency bit clock and latched in on the falling edge of the transmit bit clock.
 * If THCKP is set the falling edge of the transmit clock is used to clock the data out and frame
 * sync and the rising edge of the transmit clock is used to latch the data and frame sync in.
 */
//@{
#define BP_ESAI_TCCR_THCKP      (20)      //!< Bit position for ESAI_TCCR_THCKP.
#define BM_ESAI_TCCR_THCKP      (0x00100000)  //!< Bit mask for ESAI_TCCR_THCKP.

//! @brief Get value of ESAI_TCCR_THCKP from a register value.
#define BG_ESAI_TCCR_THCKP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_THCKP) >> BP_ESAI_TCCR_THCKP)

//! @brief Format value for bitfield ESAI_TCCR_THCKP.
#define BF_ESAI_TCCR_THCKP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_THCKP) & BM_ESAI_TCCR_THCKP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the THCKP field to a new value.
#define BW_ESAI_TCCR_THCKP(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_THCKP) | BF_ESAI_TCCR_THCKP(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TCKD[21] (RW)
 *
 * ESAI_TCCR Transmit Clock Source Direction. The Transmitter Clock Source Direction (TCKD) bit
 * selects the source of the clock signal used to clock the transmit shift registers in the
 * asynchronous mode (SYN=0) and the transmit shift registers and the receive shift registers in the
 * synchronous mode (SYN=1). When TCKD is set, the internal clock source becomes the bit clock for
 * the transmit shift registers and word length divider and is the output on the SCKT pin. When TCKD
 * is cleared, the clock source is external; the internal clock generator is disconnected from the
 * SCKT pin, and an external clock source may drive this pin (see ).
 */
//@{
#define BP_ESAI_TCCR_TCKD      (21)      //!< Bit position for ESAI_TCCR_TCKD.
#define BM_ESAI_TCCR_TCKD      (0x00200000)  //!< Bit mask for ESAI_TCCR_TCKD.

//! @brief Get value of ESAI_TCCR_TCKD from a register value.
#define BG_ESAI_TCCR_TCKD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TCKD) >> BP_ESAI_TCCR_TCKD)

//! @brief Format value for bitfield ESAI_TCCR_TCKD.
#define BF_ESAI_TCCR_TCKD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TCKD) & BM_ESAI_TCCR_TCKD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TCKD field to a new value.
#define BW_ESAI_TCCR_TCKD(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TCKD) | BF_ESAI_TCCR_TCKD(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field TFSD[22] (RW)
 *
 * ESAI_TCCR Transmit Frame Sync Signal Direction. TFSD controls the direction of the FST pin. When
 * TFSD is cleared, FST is an input; when TFSD is set, FST is an output (see ).
 */
//@{
#define BP_ESAI_TCCR_TFSD      (22)      //!< Bit position for ESAI_TCCR_TFSD.
#define BM_ESAI_TCCR_TFSD      (0x00400000)  //!< Bit mask for ESAI_TCCR_TFSD.

//! @brief Get value of ESAI_TCCR_TFSD from a register value.
#define BG_ESAI_TCCR_TFSD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_TFSD) >> BP_ESAI_TCCR_TFSD)

//! @brief Format value for bitfield ESAI_TCCR_TFSD.
#define BF_ESAI_TCCR_TFSD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_TFSD) & BM_ESAI_TCCR_TFSD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TFSD field to a new value.
#define BW_ESAI_TCCR_TFSD(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_TFSD) | BF_ESAI_TCCR_TFSD(v)))
#endif
//@}

/*! @name Register ESAI_TCCR, field THCKD[23] (RW)
 *
 * ESAI_TCCR Transmit High Frequency Clock Direction. THCKD controls the direction of the HCKT pin.
 * When THCKD is cleared, HCKT is an input; when THCKD is set, HCKT is an output (see ).
 */
//@{
#define BP_ESAI_TCCR_THCKD      (23)      //!< Bit position for ESAI_TCCR_THCKD.
#define BM_ESAI_TCCR_THCKD      (0x00800000)  //!< Bit mask for ESAI_TCCR_THCKD.

//! @brief Get value of ESAI_TCCR_THCKD from a register value.
#define BG_ESAI_TCCR_THCKD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TCCR_THCKD) >> BP_ESAI_TCCR_THCKD)

//! @brief Format value for bitfield ESAI_TCCR_THCKD.
#define BF_ESAI_TCCR_THCKD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TCCR_THCKD) & BM_ESAI_TCCR_THCKD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the THCKD field to a new value.
#define BW_ESAI_TCCR_THCKD(v)   (HW_ESAI_TCCR_WR((HW_ESAI_TCCR_RD() & ~BM_ESAI_TCCR_THCKD) | BF_ESAI_TCCR_THCKD(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RCR - Receive Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RCR - Receive Control Register (RW)
 *
 * Reset value: 0x00000000
 *
 * The read/write Receive Control Register (ESAI_RCR) controls the ESAI receiver section. Interrupt
 * enable bits for the receivers are provided in this control register. The receivers are enabled in
 * this register (0,1,2 or 3 receivers can be enabled) if the input data pin is not used by a
 * transmitter. Operating modes are also selected in this register. ESAI Receive Network Mode
 * Selection RMOD1 RMOD0 RDC4-RDC0 Receiver Network Mode 0 0 0x0-0x1F Normal Mode 0 1 0x0 On-Demand
 * Mode 0 1 0x1-0x1F Network Mode 1 0 X Reserved 1 1 0x0C AC97 ESAI Receive Slot and Word Length
 * Selection RSWS4 RSWS3 RSWS2 RSWS1 RSWS0 SLOT LENGTH WORD LENGTH 0 0 0 0 0 8 8 0 0 1 0 0 12 8 0 0
 * 0 0 1 12 0 1 0 0 0 16 8 0 0 1 0 1 12 0 0 0 1 0 16 0 1 1 0 0 20 8 0 1 0 0 1 12 0 0 1 1 0 16 0 0 0
 * 1 1 20 1 0 0 0 0 24 8 0 1 1 0 1 12 0 1 0 1 0 16 0 0 1 1 1 20 1 1 1 1 0 24 1 1 0 0 0 32 8 1 0 1 0
 * 1 12 1 0 0 1 0 16 0 1 1 1 1 20 1 1 1 1 1 24 0 1 0 1 1 Reserved 0 1 1 1 0 1 0 0 0 1 1 0 0 1 1 1 0
 * 1 0 0 1 0 1 1 0 1 0 1 1 1 1 1 0 0 1 1 1 0 1 0 1 1 0 1 1 1 1 1 0 0 1 1 1 0 1
 */
typedef union _hw_esai_rcr
{
    reg32_t U;
    struct _hw_esai_rcr_bitfields
    {
        unsigned RE0 : 1; //!< [0] ESAI_RCR ESAI Receiver 0 Enable.
        unsigned RE1 : 1; //!< [1] ESAI_RCR ESAI Receiver 1 Enable.
        unsigned RE2 : 1; //!< [2] ESAI_RCR ESAI Receiver 2 Enable.
        unsigned RE3 : 1; //!< [3] ESAI_RCR ESAI Receiver 3 Enable.
        unsigned RESERVED0 : 2; //!< [5:4] Reserved.
        unsigned RSHFD : 1; //!< [6] ESAI_RCR Receiver Shift Direction.
        unsigned RWA : 1; //!< [7] ESAI_RCR Receiver Word Alignment Control.
        unsigned RMOD : 2; //!< [9:8] ESAI_RCR Receiver Network Mode Control.
        unsigned RSWS : 5; //!< [14:10] ESAI_RCR Receiver Slot and Word Select.
        unsigned RFSL : 1; //!< [15] ESAI_RCR Receiver Frame Sync Length.
        unsigned RFSR : 1; //!< [16] ESAI_RCR Receiver Frame Sync Relative Timing.
        unsigned RESERVED1 : 2; //!< [18:17] Reserved.
        unsigned RPR : 1; //!< [19] ESAI_RCR Receiver Section Personal Reset.
        unsigned REIE : 1; //!< [20] ESAI_RCR Receive Exception Interrupt Enable.
        unsigned REDIE : 1; //!< [21] ESAI_RCR Receive Even Slot Data Interrupt Enable.
        unsigned RIE : 1; //!< [22] ESAI_RCR Receive Interrupt Enable.
        unsigned RLIE : 1; //!< [23] ESAI_RCR Receive Last Slot Interrupt Enable.
        unsigned RESERVED2 : 8; //!< [31:24] Reserved.
    } B;
} hw_esai_rcr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RCR register
 */
//@{
#define HW_ESAI_RCR_ADDR      (REGS_ESAI_BASE + 0xdc)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RCR           (*(volatile hw_esai_rcr_t *) HW_ESAI_RCR_ADDR)
#define HW_ESAI_RCR_RD()      (HW_ESAI_RCR.U)
#define HW_ESAI_RCR_WR(v)     (HW_ESAI_RCR.U = (v))
#define HW_ESAI_RCR_SET(v)    (HW_ESAI_RCR_WR(HW_ESAI_RCR_RD() |  (v)))
#define HW_ESAI_RCR_CLR(v)    (HW_ESAI_RCR_WR(HW_ESAI_RCR_RD() & ~(v)))
#define HW_ESAI_RCR_TOG(v)    (HW_ESAI_RCR_WR(HW_ESAI_RCR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_RCR bitfields
 */

/*! @name Register ESAI_RCR, field RE0[0] (RW)
 *
 * ESAI_RCR ESAI Receiver 0 Enable. When RE0 is set and TE5 is cleared, the ESAI receiver 0 is
 * enabled and samples data at the SDO5/SDI0 pin. ESAI_TX5 and ESAI_RX0 should not be enabled at the
 * same time (RE0=1 and TE5=1). When RE0 is cleared, receiver 0 is disabled by inhibiting data
 * transfer into ESAI_RX0. If this bit is cleared while receiving a data word, the remainder of the
 * word is shifted in and transferred to the ESAI_RX0 data register. If RE0 is set while some of the
 * other receivers are already in operation, the first data word received in ESAI_RX0 will be
 * invalid and must be discarded.
 */
//@{
#define BP_ESAI_RCR_RE0      (0)      //!< Bit position for ESAI_RCR_RE0.
#define BM_ESAI_RCR_RE0      (0x00000001)  //!< Bit mask for ESAI_RCR_RE0.

//! @brief Get value of ESAI_RCR_RE0 from a register value.
#define BG_ESAI_RCR_RE0(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RE0) >> BP_ESAI_RCR_RE0)

//! @brief Format value for bitfield ESAI_RCR_RE0.
#define BF_ESAI_RCR_RE0(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RE0) & BM_ESAI_RCR_RE0)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE0 field to a new value.
#define BW_ESAI_RCR_RE0(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RE0) | BF_ESAI_RCR_RE0(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RE1[1] (RW)
 *
 * ESAI_RCR ESAI Receiver 1 Enable. When RE1 is set and TE4 is cleared, the ESAI receiver 1 is
 * enabled and samples data at the SDO4/SDI1 pin. ESAI_TX4 and ESAI_RX1 should not be enabled at the
 * same time (RE1=1 and TE4=1). When RE1 is cleared, receiver 1 is disabled by inhibiting data
 * transfer into ESAI_RX1. If this bit is cleared while receiving a data word, the remainder of the
 * word is shifted in and transferred to the ESAI_RX1 data register. If RE1 is set while some of the
 * other receivers are already in operation, the first data word received in ESAI_RX1 will be
 * invalid and must be discarded.
 */
//@{
#define BP_ESAI_RCR_RE1      (1)      //!< Bit position for ESAI_RCR_RE1.
#define BM_ESAI_RCR_RE1      (0x00000002)  //!< Bit mask for ESAI_RCR_RE1.

//! @brief Get value of ESAI_RCR_RE1 from a register value.
#define BG_ESAI_RCR_RE1(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RE1) >> BP_ESAI_RCR_RE1)

//! @brief Format value for bitfield ESAI_RCR_RE1.
#define BF_ESAI_RCR_RE1(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RE1) & BM_ESAI_RCR_RE1)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE1 field to a new value.
#define BW_ESAI_RCR_RE1(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RE1) | BF_ESAI_RCR_RE1(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RE2[2] (RW)
 *
 * ESAI_RCR ESAI Receiver 2 Enable. When RE2 is set and TE3 is cleared, the ESAI receiver 2 is
 * enabled and samples data at the SDO3/SDI2 pin. ESAI_TX3 and ESAI_RX2 should not be enabled at the
 * same time (RE2=1 and TE3=1). When RE2 is cleared, receiver 2 is disabled by inhibiting data
 * transfer into ESAI_RX2. If this bit is cleared while receiving a data word, the remainder of the
 * word is shifted in and transferred to the ESAI_RX2 data register. If RE2 is set while some of the
 * other receivers are already in operation, the first data word received in ESAI_RX2 will be
 * invalid and must be discarded.
 */
//@{
#define BP_ESAI_RCR_RE2      (2)      //!< Bit position for ESAI_RCR_RE2.
#define BM_ESAI_RCR_RE2      (0x00000004)  //!< Bit mask for ESAI_RCR_RE2.

//! @brief Get value of ESAI_RCR_RE2 from a register value.
#define BG_ESAI_RCR_RE2(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RE2) >> BP_ESAI_RCR_RE2)

//! @brief Format value for bitfield ESAI_RCR_RE2.
#define BF_ESAI_RCR_RE2(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RE2) & BM_ESAI_RCR_RE2)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE2 field to a new value.
#define BW_ESAI_RCR_RE2(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RE2) | BF_ESAI_RCR_RE2(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RE3[3] (RW)
 *
 * ESAI_RCR ESAI Receiver 3 Enable. When RE3 is set and TE2 is cleared, the ESAI receiver 3 is
 * enabled and samples data at the SDO2/SDI3 pin. ESAI_TX2 and ESAI_RX3 should not be enabled at the
 * same time (RE3=1 and TE2=1). When RE3 is cleared, receiver 3 is disabled by inhibiting data
 * transfer into ESAI_RX3. If this bit is cleared while receiving a data word, the remainder of the
 * word is shifted in and transferred to the ESAI_RX3 data register. If RE3 is set while some of the
 * other receivers are already in operation, the first data word received in ESAI_RX3 will be
 * invalid and must be discarded.
 */
//@{
#define BP_ESAI_RCR_RE3      (3)      //!< Bit position for ESAI_RCR_RE3.
#define BM_ESAI_RCR_RE3      (0x00000008)  //!< Bit mask for ESAI_RCR_RE3.

//! @brief Get value of ESAI_RCR_RE3 from a register value.
#define BG_ESAI_RCR_RE3(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RE3) >> BP_ESAI_RCR_RE3)

//! @brief Format value for bitfield ESAI_RCR_RE3.
#define BF_ESAI_RCR_RE3(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RE3) & BM_ESAI_RCR_RE3)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RE3 field to a new value.
#define BW_ESAI_RCR_RE3(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RE3) | BF_ESAI_RCR_RE3(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RSHFD[6] (RW)
 *
 * ESAI_RCR Receiver Shift Direction. The RSHFD bit causes the receiver shift registers to shift
 * data in MSB first when RSHFD is cleared or LSB first when RSHFD is set (see and ).
 */
//@{
#define BP_ESAI_RCR_RSHFD      (6)      //!< Bit position for ESAI_RCR_RSHFD.
#define BM_ESAI_RCR_RSHFD      (0x00000040)  //!< Bit mask for ESAI_RCR_RSHFD.

//! @brief Get value of ESAI_RCR_RSHFD from a register value.
#define BG_ESAI_RCR_RSHFD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RSHFD) >> BP_ESAI_RCR_RSHFD)

//! @brief Format value for bitfield ESAI_RCR_RSHFD.
#define BF_ESAI_RCR_RSHFD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RSHFD) & BM_ESAI_RCR_RSHFD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RSHFD field to a new value.
#define BW_ESAI_RCR_RSHFD(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RSHFD) | BF_ESAI_RCR_RSHFD(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RWA[7] (RW)
 *
 * ESAI_RCR Receiver Word Alignment Control. The Receiver Word Alignment Control (RWA) bit defines
 * the alignment of the data word in relation to the slot. This is relevant for the cases where the
 * word length is shorter than the slot length. If RWA is cleared, the data word is assumed to be
 * left-aligned in the slot frame. If RWA is set, the data word is assumed to be right-aligned in
 * the slot frame. If the data word is shorter than the slot length, the data bits which are not in
 * the data word field are ignored. For data word lengths of less than 24 bits, the data word is
 * right-extended with zeroes before being stored in the receive data registers.
 */
//@{
#define BP_ESAI_RCR_RWA      (7)      //!< Bit position for ESAI_RCR_RWA.
#define BM_ESAI_RCR_RWA      (0x00000080)  //!< Bit mask for ESAI_RCR_RWA.

//! @brief Get value of ESAI_RCR_RWA from a register value.
#define BG_ESAI_RCR_RWA(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RWA) >> BP_ESAI_RCR_RWA)

//! @brief Format value for bitfield ESAI_RCR_RWA.
#define BF_ESAI_RCR_RWA(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RWA) & BM_ESAI_RCR_RWA)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RWA field to a new value.
#define BW_ESAI_RCR_RWA(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RWA) | BF_ESAI_RCR_RWA(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RMOD[9:8] (RW)
 *
 * ESAI_RCR Receiver Network Mode Control. The RMOD1 and RMOD0 bits are used to define the network
 * mode of the ESAI receivers, as shown in . In the normal mode, the frame rate divider determines
 * the word transfer rate - one word is transferred per frame sync during the frame sync time slot,
 * as shown in . In network mode, it is possible to transfer a word for every time slot, as shown in
 * . For more details, see . In order to comply with AC-97 specifications, RSWS4-RSWS0 should be set
 * to 0x00011 (20-bit slot, 20-bit word); RFSL and RFSR should be cleared, and RDC4-RDC0 should be
 * set to 0x0C (13 words in frame).
 */
//@{
#define BP_ESAI_RCR_RMOD      (8)      //!< Bit position for ESAI_RCR_RMOD.
#define BM_ESAI_RCR_RMOD      (0x00000300)  //!< Bit mask for ESAI_RCR_RMOD.

//! @brief Get value of ESAI_RCR_RMOD from a register value.
#define BG_ESAI_RCR_RMOD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RMOD) >> BP_ESAI_RCR_RMOD)

//! @brief Format value for bitfield ESAI_RCR_RMOD.
#define BF_ESAI_RCR_RMOD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RMOD) & BM_ESAI_RCR_RMOD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RMOD field to a new value.
#define BW_ESAI_RCR_RMOD(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RMOD) | BF_ESAI_RCR_RMOD(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RSWS[14:10] (RW)
 *
 * ESAI_RCR Receiver Slot and Word Select. The RSWS4-RSWS0 bits are used to select the length of the
 * slot and the length of the data words being received through the ESAI. The word length must be
 * equal to or shorter than the slot length. The possible combinations are shown in . See also the
 * ESAI data path programming model in and .
 */
//@{
#define BP_ESAI_RCR_RSWS      (10)      //!< Bit position for ESAI_RCR_RSWS.
#define BM_ESAI_RCR_RSWS      (0x00007c00)  //!< Bit mask for ESAI_RCR_RSWS.

//! @brief Get value of ESAI_RCR_RSWS from a register value.
#define BG_ESAI_RCR_RSWS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RSWS) >> BP_ESAI_RCR_RSWS)

//! @brief Format value for bitfield ESAI_RCR_RSWS.
#define BF_ESAI_RCR_RSWS(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RSWS) & BM_ESAI_RCR_RSWS)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RSWS field to a new value.
#define BW_ESAI_RCR_RSWS(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RSWS) | BF_ESAI_RCR_RSWS(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RFSL[15] (RW)
 *
 * ESAI_RCR Receiver Frame Sync Length. The RFSL bit selects the length of the receive frame sync to
 * be generated or recognized. If RFSL is cleared, a word-length frame sync is selected. If RFSL is
 * set, a 1-bit clock period frame sync is selected. Refer to for examples of frame length
 * selection.
 */
//@{
#define BP_ESAI_RCR_RFSL      (15)      //!< Bit position for ESAI_RCR_RFSL.
#define BM_ESAI_RCR_RFSL      (0x00008000)  //!< Bit mask for ESAI_RCR_RFSL.

//! @brief Get value of ESAI_RCR_RFSL from a register value.
#define BG_ESAI_RCR_RFSL(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RFSL) >> BP_ESAI_RCR_RFSL)

//! @brief Format value for bitfield ESAI_RCR_RFSL.
#define BF_ESAI_RCR_RFSL(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RFSL) & BM_ESAI_RCR_RFSL)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFSL field to a new value.
#define BW_ESAI_RCR_RFSL(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RFSL) | BF_ESAI_RCR_RFSL(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RFSR[16] (RW)
 *
 * ESAI_RCR Receiver Frame Sync Relative Timing. RFSR determines the relative timing of the receive
 * frame sync signal as referred to the serial data lines, for a word length frame sync only. When
 * RFSR is cleared the word length frame sync occurs together with the first bit of the data word of
 * the first slot. When RFSR is set the word length frame sync starts one serial clock cycle
 * earlier, that is, together with the last bit of the previous data word.
 */
//@{
#define BP_ESAI_RCR_RFSR      (16)      //!< Bit position for ESAI_RCR_RFSR.
#define BM_ESAI_RCR_RFSR      (0x00010000)  //!< Bit mask for ESAI_RCR_RFSR.

//! @brief Get value of ESAI_RCR_RFSR from a register value.
#define BG_ESAI_RCR_RFSR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RFSR) >> BP_ESAI_RCR_RFSR)

//! @brief Format value for bitfield ESAI_RCR_RFSR.
#define BF_ESAI_RCR_RFSR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RFSR) & BM_ESAI_RCR_RFSR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFSR field to a new value.
#define BW_ESAI_RCR_RFSR(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RFSR) | BF_ESAI_RCR_RFSR(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RPR[19] (RW)
 *
 * ESAI_RCR Receiver Section Personal Reset. The RPR control bit is used to put the receiver section
 * of the ESAI in the personal reset state. The transmitter section is not affected. When RPR is
 * cleared, the receiver section may operate normally. When RPR is set, the receiver section enters
 * the personal reset state immediately. When in the personal reset state, the status bits are reset
 * to the same state as after hardware reset.The control bits are not affected by the personal reset
 * state.The receiver data pins are disconnected while in the personal reset state. To leave the
 * personal reset state by clearing RPR, the procedure described in should be followed.
 */
//@{
#define BP_ESAI_RCR_RPR      (19)      //!< Bit position for ESAI_RCR_RPR.
#define BM_ESAI_RCR_RPR      (0x00080000)  //!< Bit mask for ESAI_RCR_RPR.

//! @brief Get value of ESAI_RCR_RPR from a register value.
#define BG_ESAI_RCR_RPR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RPR) >> BP_ESAI_RCR_RPR)

//! @brief Format value for bitfield ESAI_RCR_RPR.
#define BF_ESAI_RCR_RPR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RPR) & BM_ESAI_RCR_RPR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RPR field to a new value.
#define BW_ESAI_RCR_RPR(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RPR) | BF_ESAI_RCR_RPR(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field REIE[20] (RW)
 *
 * ESAI_RCR Receive Exception Interrupt Enable. When REIE is set, the Core is interrupted when both
 * RDF and ROE in the ESAI_SAISR status register are set. When REIE is cleared, this interrupt is
 * disabled. Reading the ESAI_SAISR status register followed by reading the enabled receivers data
 * registers clears ROE, thus clearing the pending interrupt.
 */
//@{
#define BP_ESAI_RCR_REIE      (20)      //!< Bit position for ESAI_RCR_REIE.
#define BM_ESAI_RCR_REIE      (0x00100000)  //!< Bit mask for ESAI_RCR_REIE.

//! @brief Get value of ESAI_RCR_REIE from a register value.
#define BG_ESAI_RCR_REIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_REIE) >> BP_ESAI_RCR_REIE)

//! @brief Format value for bitfield ESAI_RCR_REIE.
#define BF_ESAI_RCR_REIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_REIE) & BM_ESAI_RCR_REIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the REIE field to a new value.
#define BW_ESAI_RCR_REIE(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_REIE) | BF_ESAI_RCR_REIE(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field REDIE[21] (RW)
 *
 * ESAI_RCR Receive Even Slot Data Interrupt Enable. The REDIE control bit is used to enable the
 * receive even slot data interrupts. If REDIE is set, the receive even slot data interrupts are
 * enabled. If REDIE is cleared, the receive even slot data interrupts are disabled. A receive even
 * slot data interrupt request is generated if REDIE is set and the REDF status flag in the
 * ESAI_SAISR status register is set. Even time slots are all even-numbered time slots (0, 2, 4,
 * etc.) when operating in network mode. The zero time slot is marked by the frame sync signal and
 * is considered to be even. Reading all the data registers of the enabled receivers clears the REDF
 * flag, thus servicing the interrupt. Receive interrupts with exception have higher priority than
 * receive even slot data interrupts, therefore if exception occurs (ROE is set) and REIE is set,
 * the ESAI requests an ESAI receive data with exception interrupt from the interrupt controller.
 */
//@{
#define BP_ESAI_RCR_REDIE      (21)      //!< Bit position for ESAI_RCR_REDIE.
#define BM_ESAI_RCR_REDIE      (0x00200000)  //!< Bit mask for ESAI_RCR_REDIE.

//! @brief Get value of ESAI_RCR_REDIE from a register value.
#define BG_ESAI_RCR_REDIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_REDIE) >> BP_ESAI_RCR_REDIE)

//! @brief Format value for bitfield ESAI_RCR_REDIE.
#define BF_ESAI_RCR_REDIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_REDIE) & BM_ESAI_RCR_REDIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the REDIE field to a new value.
#define BW_ESAI_RCR_REDIE(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_REDIE) | BF_ESAI_RCR_REDIE(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RIE[22] (RW)
 *
 * ESAI_RCR Receive Interrupt Enable. The Core is interrupted when RIE and the RDF flag in the
 * ESAI_SAISR status register are set. When RIE is cleared, this interrupt is disabled. Reading the
 * receive data registers of the enabled receivers clears RDF, thus clearing the interrupt. Receive
 * interrupts with exception have higher priority than normal receive data interrupts, therefore if
 * exception occurs (ROE is set) and REIE is set, the ESAI requests an ESAI receive data with
 * exception interrupt from the interrupt controller.
 */
//@{
#define BP_ESAI_RCR_RIE      (22)      //!< Bit position for ESAI_RCR_RIE.
#define BM_ESAI_RCR_RIE      (0x00400000)  //!< Bit mask for ESAI_RCR_RIE.

//! @brief Get value of ESAI_RCR_RIE from a register value.
#define BG_ESAI_RCR_RIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RIE) >> BP_ESAI_RCR_RIE)

//! @brief Format value for bitfield ESAI_RCR_RIE.
#define BF_ESAI_RCR_RIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RIE) & BM_ESAI_RCR_RIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RIE field to a new value.
#define BW_ESAI_RCR_RIE(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RIE) | BF_ESAI_RCR_RIE(v)))
#endif
//@}

/*! @name Register ESAI_RCR, field RLIE[23] (RW)
 *
 * ESAI_RCR Receive Last Slot Interrupt Enable. RLIE enables an interrupt after the last slot of a
 * frame ended in network mode only. When RLIE is set the Core is interrupted after the last slot in
 * a frame ended regardless of the receive mask register setting. When RLIE is cleared the receive
 * last slot interrupt is disabled. Hardware and software reset clear RLIE. RLIE is disabled when
 * RDC[4:0]=00000 (on-demand mode). The use of the receive last slot interrupt is described in .
 */
//@{
#define BP_ESAI_RCR_RLIE      (23)      //!< Bit position for ESAI_RCR_RLIE.
#define BM_ESAI_RCR_RLIE      (0x00800000)  //!< Bit mask for ESAI_RCR_RLIE.

//! @brief Get value of ESAI_RCR_RLIE from a register value.
#define BG_ESAI_RCR_RLIE(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCR_RLIE) >> BP_ESAI_RCR_RLIE)

//! @brief Format value for bitfield ESAI_RCR_RLIE.
#define BF_ESAI_RCR_RLIE(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCR_RLIE) & BM_ESAI_RCR_RLIE)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RLIE field to a new value.
#define BW_ESAI_RCR_RLIE(v)   (HW_ESAI_RCR_WR((HW_ESAI_RCR_RD() & ~BM_ESAI_RCR_RLIE) | BF_ESAI_RCR_RLIE(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RCCR - Receive Clock Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RCCR - Receive Clock Control Register (RW)
 *
 * Reset value: 0x00000000
 *
 * The read/write Receiver Clock Control Register (ESAI_RCCR) controls the ESAI receiver clock
 * generator bit and frame sync rates, word length, and number of words per frame for the serial
 * data. The ESAI_RCCR control bits are described in the following paragraphs. ARM Core clock is
 * ipg_clk_esai in block ESAI which is from CCM's ahb_clk_root. Receiver High Frequency Clock
 * Divider RFP3-RFP0 Divide Ratio 0x0 1 0x1 2 0x2 3 0x3 4 ... ... 0xF 16 SCKR Pin Definition Table
 * Control Bits SCKR PIN SYN RCKD 0 0 SCKR input 0 1 SCKR output 1 0 IF0 1 1 OF0 FSR Pin Definition
 * Table Control Bits FSR Pin SYN TEBE RFSD 0 X 0 FSR input 0 X 1 FSR output 1 0 0 IF1 1 0 1 OF1 1 1
 * 0 reserved 1 1 1 Transmitter Buffer Enable HCKR Pin Definition Table Control Bits HCKR PIN SYN
 * RHCKD 0 0 HCKR input 0 1 HCKR output 1 0 IF2 1 1 OF2
 */
typedef union _hw_esai_rccr
{
    reg32_t U;
    struct _hw_esai_rccr_bitfields
    {
        unsigned RPM : 8; //!< [7:0] ESAI_RCCR Receiver Prescale Modulus Select.
        unsigned RPSR : 1; //!< [8] ESAI_RCCR Receiver Prescaler Range.
        unsigned RDC : 5; //!< [13:9] ESAI_RCCR Rx Frame Rate Divider Control.
        unsigned RFP : 4; //!< [17:14] ESAI_RCCR Rx High Frequency Clock Divider.
        unsigned RCKP : 1; //!< [18] The Receiver Clock Polarity (RCKP) bit controls on which bit clock edge data and frame sync are clocked out and latched in.
        unsigned RFSP : 1; //!< [19] ESAI_RCCR Receiver Frame Sync Polarity.
        unsigned RHCKP : 1; //!< [20] ESAI_RCCR Receiver High Frequency Clock Polarity.
        unsigned RCKD : 1; //!< [21] ESAI_RCCR Receiver Clock Source Direction.
        unsigned RFSD : 1; //!< [22] ESAI_RCCR Receiver Frame Sync Signal Direction.
        unsigned RHCKD : 1; //!< [23] ESAI_RCCR Receiver High Frequency Clock Direction.
        unsigned RESERVED0 : 8; //!< [31:24] Reserved.
    } B;
} hw_esai_rccr_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RCCR register
 */
//@{
#define HW_ESAI_RCCR_ADDR      (REGS_ESAI_BASE + 0xe0)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RCCR           (*(volatile hw_esai_rccr_t *) HW_ESAI_RCCR_ADDR)
#define HW_ESAI_RCCR_RD()      (HW_ESAI_RCCR.U)
#define HW_ESAI_RCCR_WR(v)     (HW_ESAI_RCCR.U = (v))
#define HW_ESAI_RCCR_SET(v)    (HW_ESAI_RCCR_WR(HW_ESAI_RCCR_RD() |  (v)))
#define HW_ESAI_RCCR_CLR(v)    (HW_ESAI_RCCR_WR(HW_ESAI_RCCR_RD() & ~(v)))
#define HW_ESAI_RCCR_TOG(v)    (HW_ESAI_RCCR_WR(HW_ESAI_RCCR_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_RCCR bitfields
 */

/*! @name Register ESAI_RCCR, field RPM[7:0] (RW)
 *
 * ESAI_RCCR Receiver Prescale Modulus Select. The RPM7-RPM0 bits specify the divide ratio of the
 * prescale divider in the ESAI receiver clock generator. A divide ratio from 1 to 256
 * (RPM[7:0]=0x00 to 0xFF) may be selected. The bit clock output is available at the receiver serial
 * bit clock (SCKR) pin. The bit clock output is also available internally for use as the bit clock
 * to shift the receive shift registers. The ESAI receive clock generator functional diagram is
 * shown in .
 */
//@{
#define BP_ESAI_RCCR_RPM      (0)      //!< Bit position for ESAI_RCCR_RPM.
#define BM_ESAI_RCCR_RPM      (0x000000ff)  //!< Bit mask for ESAI_RCCR_RPM.

//! @brief Get value of ESAI_RCCR_RPM from a register value.
#define BG_ESAI_RCCR_RPM(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RPM) >> BP_ESAI_RCCR_RPM)

//! @brief Format value for bitfield ESAI_RCCR_RPM.
#define BF_ESAI_RCCR_RPM(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RPM) & BM_ESAI_RCCR_RPM)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RPM field to a new value.
#define BW_ESAI_RCCR_RPM(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RPM) | BF_ESAI_RCCR_RPM(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RPSR[8] (RW)
 *
 * ESAI_RCCR Receiver Prescaler Range. The RPSR controls a fixed divide-by-eight prescaler in series
 * with the variable prescaler. This bit is used to extend the range of the prescaler for those
 * cases where a slower bit clock is desired. When RPSR is set, the fixed prescaler is bypassed.
 * When RPSR is cleared, the fixed divide-by-eight prescaler is operational (see ). The maximum
 * internally generated bit clock frequency is Fsys/4, the minimum internally generated bit clock
 * frequency is Fsys/(2 x 8 x 256 x 16)=Fsys/65536. (Do not use the combination RPSR=1 and RPM7-RPM0
 * =0x00, which causes synchronization problems when using the internal Core clock as source
 * (RHCKD=1 or RCKD=1))
 */
//@{
#define BP_ESAI_RCCR_RPSR      (8)      //!< Bit position for ESAI_RCCR_RPSR.
#define BM_ESAI_RCCR_RPSR      (0x00000100)  //!< Bit mask for ESAI_RCCR_RPSR.

//! @brief Get value of ESAI_RCCR_RPSR from a register value.
#define BG_ESAI_RCCR_RPSR(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RPSR) >> BP_ESAI_RCCR_RPSR)

//! @brief Format value for bitfield ESAI_RCCR_RPSR.
#define BF_ESAI_RCCR_RPSR(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RPSR) & BM_ESAI_RCCR_RPSR)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RPSR field to a new value.
#define BW_ESAI_RCCR_RPSR(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RPSR) | BF_ESAI_RCCR_RPSR(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RDC[13:9] (RW)
 *
 * ESAI_RCCR Rx Frame Rate Divider Control. The RDC4-RDC0 bits control the divide ratio for the
 * programmable frame rate dividers used to generate the receiver frame clocks. In network mode,
 * this ratio may be interpreted as the number of words per frame minus one. The divide ratio may
 * range from 2 to 32 (RDC[4:0]=0x00001 to 0x11111) for network mode. A divide ratio of one
 * (RDC[4:0]=0x00000) in network mode is a special case (on-demand mode). In normal mode, this ratio
 * determines the word transfer rate. The divide ratio may range from 1 to 32 (RDC[4:0]=0x00000 to
 * 0x11111) for normal mode. In normal mode, a divide ratio of one (RDC[4:0]=0x00000) provides
 * continuous periodic data word transfers. A bit-length frame sync (RFSL=1) must be used in this
 * case. The ESAI frame sync generator functional diagram is shown in .
 */
//@{
#define BP_ESAI_RCCR_RDC      (9)      //!< Bit position for ESAI_RCCR_RDC.
#define BM_ESAI_RCCR_RDC      (0x00003e00)  //!< Bit mask for ESAI_RCCR_RDC.

//! @brief Get value of ESAI_RCCR_RDC from a register value.
#define BG_ESAI_RCCR_RDC(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RDC) >> BP_ESAI_RCCR_RDC)

//! @brief Format value for bitfield ESAI_RCCR_RDC.
#define BF_ESAI_RCCR_RDC(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RDC) & BM_ESAI_RCCR_RDC)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RDC field to a new value.
#define BW_ESAI_RCCR_RDC(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RDC) | BF_ESAI_RCCR_RDC(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RFP[17:14] (RW)
 *
 * ESAI_RCCR Rx High Frequency Clock Divider. The RFP3-RFP0 bits control the divide ratio of the
 * receiver high frequency clock to the receiver serial bit clock when the source of the receiver
 * high frequency clock and the bit clock is the internal Arm Core clock. When the HCKR input is
 * being driven from an external high frequency clock, the RFP3-RFP0 bits specify an additional
 * division ration in the clock divider chain. provides the specification of the divide ratio. shows
 * the ESAI high frequency generator functional diagram.
 */
//@{
#define BP_ESAI_RCCR_RFP      (14)      //!< Bit position for ESAI_RCCR_RFP.
#define BM_ESAI_RCCR_RFP      (0x0003c000)  //!< Bit mask for ESAI_RCCR_RFP.

//! @brief Get value of ESAI_RCCR_RFP from a register value.
#define BG_ESAI_RCCR_RFP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RFP) >> BP_ESAI_RCCR_RFP)

//! @brief Format value for bitfield ESAI_RCCR_RFP.
#define BF_ESAI_RCCR_RFP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RFP) & BM_ESAI_RCCR_RFP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFP field to a new value.
#define BW_ESAI_RCCR_RFP(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RFP) | BF_ESAI_RCCR_RFP(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RCKP[18] (RW)
 *
 * The Receiver Clock Polarity (RCKP) bit controls on which bit clock edge data and frame sync are
 * clocked out and latched in. If RCKP is cleared the data and the frame sync are clocked out on the
 * rising edge of the receive bit clock and the frame sync is latched in on the falling edge of the
 * receive bit clock. If RCKP is set the falling edge of the receive clock is used to clock the data
 * and frame sync out and the rising edge of the receive clock is used to latch the frame sync in.
 */
//@{
#define BP_ESAI_RCCR_RCKP      (18)      //!< Bit position for ESAI_RCCR_RCKP.
#define BM_ESAI_RCCR_RCKP      (0x00040000)  //!< Bit mask for ESAI_RCCR_RCKP.

//! @brief Get value of ESAI_RCCR_RCKP from a register value.
#define BG_ESAI_RCCR_RCKP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RCKP) >> BP_ESAI_RCCR_RCKP)

//! @brief Format value for bitfield ESAI_RCCR_RCKP.
#define BF_ESAI_RCCR_RCKP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RCKP) & BM_ESAI_RCCR_RCKP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RCKP field to a new value.
#define BW_ESAI_RCCR_RCKP(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RCKP) | BF_ESAI_RCCR_RCKP(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RFSP[19] (RW)
 *
 * ESAI_RCCR Receiver Frame Sync Polarity. The Receiver Frame Sync Polarity (RFSP) determines the
 * polarity of the receive frame sync signal. When RFSP is cleared the frame sync signal polarity is
 * positive, that is, the frame start is indicated by a high level on the frame sync pin. When RFSP
 * is set the frame sync signal polarity is negative, that is, the frame start is indicated by a low
 * level on the frame sync pin.
 */
//@{
#define BP_ESAI_RCCR_RFSP      (19)      //!< Bit position for ESAI_RCCR_RFSP.
#define BM_ESAI_RCCR_RFSP      (0x00080000)  //!< Bit mask for ESAI_RCCR_RFSP.

//! @brief Get value of ESAI_RCCR_RFSP from a register value.
#define BG_ESAI_RCCR_RFSP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RFSP) >> BP_ESAI_RCCR_RFSP)

//! @brief Format value for bitfield ESAI_RCCR_RFSP.
#define BF_ESAI_RCCR_RFSP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RFSP) & BM_ESAI_RCCR_RFSP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFSP field to a new value.
#define BW_ESAI_RCCR_RFSP(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RFSP) | BF_ESAI_RCCR_RFSP(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RHCKP[20] (RW)
 *
 * ESAI_RCCR Receiver High Frequency Clock Polarity. The Receiver High Frequency Clock Polarity
 * (RHCKP) bit controls on which bit clock edge data and frame sync are clocked out and latched in.
 * If RHCKP is cleared the data and the frame sync are clocked out on the rising edge of the receive
 * high frequency bit clock and the frame sync is latched in on the falling edge of the receive bit
 * clock. If RHCKP is set the falling edge of the receive clock is used to clock the data and frame
 * sync out and the rising edge of the receive clock is used to latch the frame sync in.
 */
//@{
#define BP_ESAI_RCCR_RHCKP      (20)      //!< Bit position for ESAI_RCCR_RHCKP.
#define BM_ESAI_RCCR_RHCKP      (0x00100000)  //!< Bit mask for ESAI_RCCR_RHCKP.

//! @brief Get value of ESAI_RCCR_RHCKP from a register value.
#define BG_ESAI_RCCR_RHCKP(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RHCKP) >> BP_ESAI_RCCR_RHCKP)

//! @brief Format value for bitfield ESAI_RCCR_RHCKP.
#define BF_ESAI_RCCR_RHCKP(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RHCKP) & BM_ESAI_RCCR_RHCKP)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RHCKP field to a new value.
#define BW_ESAI_RCCR_RHCKP(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RHCKP) | BF_ESAI_RCCR_RHCKP(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RCKD[21] (RW)
 *
 * ESAI_RCCR Receiver Clock Source Direction. The Receiver Clock Source Direction (RCKD) bit selects
 * the source of the clock signal used to clock the receive shift register in the asynchronous mode
 * (SYN=0) and the IF0/OF0 flag direction in the synchronous mode (SYN=1). In the asynchronous mode,
 * when RCKD is set, the internal clock source becomes the bit clock for the receive shift registers
 * and word length divider and is the output on the SCKR pin. In the asynchronous mode when RCKD is
 * cleared, the clock source is external; the internal clock generator is disconnected from the SCKR
 * pin, and an external clock source may drive this pin. In the synchronous mode when RCKD is set,
 * the SCKR pin becomes the OF0 output flag. If RCKD is cleared, the SCKR pin becomes the IF0 input
 * flag. Refer to and .
 */
//@{
#define BP_ESAI_RCCR_RCKD      (21)      //!< Bit position for ESAI_RCCR_RCKD.
#define BM_ESAI_RCCR_RCKD      (0x00200000)  //!< Bit mask for ESAI_RCCR_RCKD.

//! @brief Get value of ESAI_RCCR_RCKD from a register value.
#define BG_ESAI_RCCR_RCKD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RCKD) >> BP_ESAI_RCCR_RCKD)

//! @brief Format value for bitfield ESAI_RCCR_RCKD.
#define BF_ESAI_RCCR_RCKD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RCKD) & BM_ESAI_RCCR_RCKD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RCKD field to a new value.
#define BW_ESAI_RCCR_RCKD(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RCKD) | BF_ESAI_RCCR_RCKD(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RFSD[22] (RW)
 *
 * ESAI_RCCR Receiver Frame Sync Signal Direction. The Receiver Frame Sync Signal Direction (RFSD)
 * bit selects the source of the receiver frame sync signal when in the asynchronous mode (SYN=0)
 * and the IF1/OF1/Transmitter Buffer Enable flag direction in the synchronous mode (SYN=1). In the
 * asynchronous mode, when RFSD is set, the internal clock generator becomes the source of the
 * receiver frame sync and is the output on the FSR pin. In the asynchronous mode, when RFSD is
 * cleared, the receiver frame sync source is external; the internal clock generator is disconnected
 * from the FSR pin, and an external clock source may drive this pin. In the synchronous mode when
 * RFSD is set, the FSR pin becomes the OF1 output flag or the Transmitter Buffer Enable, according
 * to the TEBE control bit. If RFSD is cleared, the FSR pin becomes the IF1 input flag. Refer to and
 * .
 */
//@{
#define BP_ESAI_RCCR_RFSD      (22)      //!< Bit position for ESAI_RCCR_RFSD.
#define BM_ESAI_RCCR_RFSD      (0x00400000)  //!< Bit mask for ESAI_RCCR_RFSD.

//! @brief Get value of ESAI_RCCR_RFSD from a register value.
#define BG_ESAI_RCCR_RFSD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RFSD) >> BP_ESAI_RCCR_RFSD)

//! @brief Format value for bitfield ESAI_RCCR_RFSD.
#define BF_ESAI_RCCR_RFSD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RFSD) & BM_ESAI_RCCR_RFSD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RFSD field to a new value.
#define BW_ESAI_RCCR_RFSD(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RFSD) | BF_ESAI_RCCR_RFSD(v)))
#endif
//@}

/*! @name Register ESAI_RCCR, field RHCKD[23] (RW)
 *
 * ESAI_RCCR Receiver High Frequency Clock Direction. The Receiver High Frequency Clock Direction
 * (RHCKD) bit selects the source of the receiver high frequency clock when in the asynchronous mode
 * (SYN=0) and the IF2/OF2 flag direction in the synchronous mode (SYN=1). In the asynchronous mode,
 * when RHCKD is set, the internal clock generator becomes the source of the receiver high frequency
 * clock and is the output on the HCKR pin. In the asynchronous mode, when RHCKD is cleared, the
 * receiver high frequency clock source is external; the internal clock generator is disconnected
 * from the HCKR pin, and an external clock source may drive this pin. When RHCKD is cleared, HCKR
 * is an input; when RHCKD is set, HCKR is an output. In the synchronous mode when RHCKD is set, the
 * HCKR pin becomes the OF2 output flag. If RHCKD is cleared, the HCKR pin becomes the IF2 input
 * flag. Refer to and .
 */
//@{
#define BP_ESAI_RCCR_RHCKD      (23)      //!< Bit position for ESAI_RCCR_RHCKD.
#define BM_ESAI_RCCR_RHCKD      (0x00800000)  //!< Bit mask for ESAI_RCCR_RHCKD.

//! @brief Get value of ESAI_RCCR_RHCKD from a register value.
#define BG_ESAI_RCCR_RHCKD(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RCCR_RHCKD) >> BP_ESAI_RCCR_RHCKD)

//! @brief Format value for bitfield ESAI_RCCR_RHCKD.
#define BF_ESAI_RCCR_RHCKD(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RCCR_RHCKD) & BM_ESAI_RCCR_RHCKD)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RHCKD field to a new value.
#define BW_ESAI_RCCR_RHCKD(v)   (HW_ESAI_RCCR_WR((HW_ESAI_RCCR_RD() & ~BM_ESAI_RCCR_RHCKD) | BF_ESAI_RCCR_RHCKD(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TSMA - Transmit Slot Mask Register A
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TSMA - Transmit Slot Mask Register A (RW)
 *
 * Reset value: 0x0000ffff
 *
 * The Transmit Slot Mask Register A together with Transmit Slot Mask Register B (ESAI_TSMA and
 * ESAI_TSMB) are two read/write registers used by the transmitters in network mode to determine for
 * each slot whether to transmit a data word and generate a transmitter empty condition (TDE=1), or
 * to tri-state the transmitter data pins. Fields ESAI_TSMA [TS[15:0]] and ESAI_TSMB [TS[31:16]] are
 * concatenated to form the 32-bit field TS[31:0]. Bit number n in TS[31:0] is the enable/disable
 * control bit for transmission in slot number n.
 */
typedef union _hw_esai_tsma
{
    reg32_t U;
    struct _hw_esai_tsma_bitfields
    {
        unsigned TS : 16; //!< [15:0] When bit number N in ESAI_TSMA is cleared, all the transmit data pins of the enabled transmitters are tri-stated during transmit time slot number N.
        unsigned RESERVED0 : 16; //!< [31:16] Reserved
    } B;
} hw_esai_tsma_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TSMA register
 */
//@{
#define HW_ESAI_TSMA_ADDR      (REGS_ESAI_BASE + 0xe4)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TSMA           (*(volatile hw_esai_tsma_t *) HW_ESAI_TSMA_ADDR)
#define HW_ESAI_TSMA_RD()      (HW_ESAI_TSMA.U)
#define HW_ESAI_TSMA_WR(v)     (HW_ESAI_TSMA.U = (v))
#define HW_ESAI_TSMA_SET(v)    (HW_ESAI_TSMA_WR(HW_ESAI_TSMA_RD() |  (v)))
#define HW_ESAI_TSMA_CLR(v)    (HW_ESAI_TSMA_WR(HW_ESAI_TSMA_RD() & ~(v)))
#define HW_ESAI_TSMA_TOG(v)    (HW_ESAI_TSMA_WR(HW_ESAI_TSMA_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_TSMA bitfields
 */

/*! @name Register ESAI_TSMA, field TS[15:0] (RW)
 *
 * When bit number N in ESAI_TSMA is cleared, all the transmit data pins of the enabled transmitters
 * are tri-stated during transmit time slot number N. The data is still transferred from the
 * transmit data registers to the transmit shift registers but neither the TDE nor the TUE flags are
 * set. This means that during a disabled slot, no transmitter empty interrupt is generated. The
 * Core is interrupted only for enabled slots. Data that is written to the transmit data registers
 * when servicing this request is transmitted in the next enabled transmit time slot. When bit
 * number N in ESAI_TSMA register is set, the transmit sequence is as usual: data is transferred
 * from the TX registers to the shift registers and transmitted during slot number N, and the TDE
 * flag is set. Using the slot mask in ESAI_TSMA does not conflict with using TSR. Even if a slot is
 * enabled in ESAI_TSMA, the user may choose to write to TSR instead of writing to the transmit data
 * registers TXn. This causes all the transmit data pins of the enabled transmitters to be tri-
 * stated during the next slot. Data written to the ESAI_TSMA affects the next frame transmission.
 * The frame being transmitted is not affected by this data and would comply to the last ESAI_TSMA
 * setting. Data read from ESAI_TSMA returns the last written data. After hardware or software
 * reset, the ESAI_TSMA register is preset to 0x0000FFFF, which means that all 16 possible slots are
 * enabled for data transmission. When operating in normal mode, bit 0 of the ESAI_TSMA register
 * must be set, otherwise no output is generated.
 */
//@{
#define BP_ESAI_TSMA_TS      (0)      //!< Bit position for ESAI_TSMA_TS.
#define BM_ESAI_TSMA_TS      (0x0000ffff)  //!< Bit mask for ESAI_TSMA_TS.

//! @brief Get value of ESAI_TSMA_TS from a register value.
#define BG_ESAI_TSMA_TS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TSMA_TS) >> BP_ESAI_TSMA_TS)

//! @brief Format value for bitfield ESAI_TSMA_TS.
#define BF_ESAI_TSMA_TS(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TSMA_TS) & BM_ESAI_TSMA_TS)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TS field to a new value.
#define BW_ESAI_TSMA_TS(v)   (HW_ESAI_TSMA_WR((HW_ESAI_TSMA_RD() & ~BM_ESAI_TSMA_TS) | BF_ESAI_TSMA_TS(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_TSMB - Transmit Slot Mask Register B
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_TSMB - Transmit Slot Mask Register B (RW)
 *
 * Reset value: 0x0000ffff
 *
 * The Transmit Slot Mask Register B together with Transmit Slot Mask Register A (ESAI_TSMA and
 * ESAI_TSMB) are two read/write registers used by the transmitters in network mode to determine for
 * each slot whether to transmit a data word and generate a transmitter empty condition (TDE=1), or
 * to tri-state the transmitter data pins. Fields ESAI_TSMA [TS[15:0]] and ESAI_TSMB [TS[31:16]] are
 * concatenated to form the 32-bit field TS[31:0]. Bit number n in TS[31:0] is the enable/disable
 * control bit for transmission in slot number n.
 */
typedef union _hw_esai_tsmb
{
    reg32_t U;
    struct _hw_esai_tsmb_bitfields
    {
        unsigned TS : 16; //!< [15:0] When bit number N in ESAI_TSMB is cleared, all the transmit data pins of the enabled transmitters are tri-stated during transmit time slot number N.
        unsigned RESERVED0 : 16; //!< [31:16] Reserved
    } B;
} hw_esai_tsmb_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_TSMB register
 */
//@{
#define HW_ESAI_TSMB_ADDR      (REGS_ESAI_BASE + 0xe8)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_TSMB           (*(volatile hw_esai_tsmb_t *) HW_ESAI_TSMB_ADDR)
#define HW_ESAI_TSMB_RD()      (HW_ESAI_TSMB.U)
#define HW_ESAI_TSMB_WR(v)     (HW_ESAI_TSMB.U = (v))
#define HW_ESAI_TSMB_SET(v)    (HW_ESAI_TSMB_WR(HW_ESAI_TSMB_RD() |  (v)))
#define HW_ESAI_TSMB_CLR(v)    (HW_ESAI_TSMB_WR(HW_ESAI_TSMB_RD() & ~(v)))
#define HW_ESAI_TSMB_TOG(v)    (HW_ESAI_TSMB_WR(HW_ESAI_TSMB_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_TSMB bitfields
 */

/*! @name Register ESAI_TSMB, field TS[15:0] (RW)
 *
 * When bit number N in ESAI_TSMB is cleared, all the transmit data pins of the enabled transmitters
 * are tri-stated during transmit time slot number N. The data is still transferred from the
 * transmit data registers to the transmit shift registers but neither the TDE nor the TUE flags are
 * set. This means that during a disabled slot, no transmitter empty interrupt is generated. The
 * Core is interrupted only for enabled slots. Data that is written to the transmit data registers
 * when servicing this request is transmitted in the next enabled transmit time slot. When bit
 * number N in ESAI_TSMB register is set, the transmit sequence is as usual: data is transferred
 * from the TX registers to the shift registers and transmitted during slot number N, and the TDE
 * flag is set. Using the slot mask in ESAI_TSMB does not conflict with using TSR. Even if a slot is
 * enabled in TSMB, the user may chose to write to TSR instead of writing to the transmit data
 * registers TXn. This causes all the transmit data pins of the enabled transmitters to be tri-
 * stated during the next slot. Data written to the ESAI_TSMB affects the next frame transmission.
 * The frame being transmitted is not affected by this data and would comply to the last ESAI_TSMB
 * setting. Data read from ESAI_TSMB returns the last written data. After hardware or software
 * reset, the ESAI_TSMB register is preset to 0x0000FFFF, which means that all 16 possible slots are
 * enabled for data transmission.
 */
//@{
#define BP_ESAI_TSMB_TS      (0)      //!< Bit position for ESAI_TSMB_TS.
#define BM_ESAI_TSMB_TS      (0x0000ffff)  //!< Bit mask for ESAI_TSMB_TS.

//! @brief Get value of ESAI_TSMB_TS from a register value.
#define BG_ESAI_TSMB_TS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_TSMB_TS) >> BP_ESAI_TSMB_TS)

//! @brief Format value for bitfield ESAI_TSMB_TS.
#define BF_ESAI_TSMB_TS(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_TSMB_TS) & BM_ESAI_TSMB_TS)

#ifndef __LANGUAGE_ASM__
//! @brief Set the TS field to a new value.
#define BW_ESAI_TSMB_TS(v)   (HW_ESAI_TSMB_WR((HW_ESAI_TSMB_RD() & ~BM_ESAI_TSMB_TS) | BF_ESAI_TSMB_TS(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RSMA - Receive Slot Mask Register A
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RSMA - Receive Slot Mask Register A (RW)
 *
 * Reset value: 0x0000ffff
 *
 * The Receive Slot Mask Register A together with Receive Slot Mask Register B (ESAI_RSMA and
 * ESAI_RSMB) are two read/write registers used by the receiver in network mode to determine for
 * each slot whether to receive a data word and generate a receiver full condition (RDF=1), or to
 * ignore the received data. Fields ESAI_RSMA [RS[15:0]] and ESAI_RSMB [RS31:16]] are concatenated
 * to form the 32-bit field RS[31:0]. Bit number n in RS[31:0] is an enable/disable control bit for
 * receiving data in slot number n.
 */
typedef union _hw_esai_rsma
{
    reg32_t U;
    struct _hw_esai_rsma_bitfields
    {
        unsigned RS : 16; //!< [15:0] When bit number N in the ESAI_RSMA register is cleared, the data from the enabled receivers input pins are shifted into their receive shift registers during slot number N.
        unsigned RESERVED0 : 16; //!< [31:16] Reserved
    } B;
} hw_esai_rsma_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RSMA register
 */
//@{
#define HW_ESAI_RSMA_ADDR      (REGS_ESAI_BASE + 0xec)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RSMA           (*(volatile hw_esai_rsma_t *) HW_ESAI_RSMA_ADDR)
#define HW_ESAI_RSMA_RD()      (HW_ESAI_RSMA.U)
#define HW_ESAI_RSMA_WR(v)     (HW_ESAI_RSMA.U = (v))
#define HW_ESAI_RSMA_SET(v)    (HW_ESAI_RSMA_WR(HW_ESAI_RSMA_RD() |  (v)))
#define HW_ESAI_RSMA_CLR(v)    (HW_ESAI_RSMA_WR(HW_ESAI_RSMA_RD() & ~(v)))
#define HW_ESAI_RSMA_TOG(v)    (HW_ESAI_RSMA_WR(HW_ESAI_RSMA_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_RSMA bitfields
 */

/*! @name Register ESAI_RSMA, field RS[15:0] (RW)
 *
 * When bit number N in the ESAI_RSMA register is cleared, the data from the enabled receivers input
 * pins are shifted into their receive shift registers during slot number N. The data is not
 * transferred from the receive shift registers to the receive data registers, and neither the RDF
 * nor the ROE flag is set. This means that during a disabled slot, no receiver full interrupt is
 * generated. The Core is interrupted only for enabled slots. When bit number N in the ESAI_RSMA is
 * set, the receive sequence is as usual: data which is shifted into the enabled receivers shift
 * registers is transferred to the receive data registers and the RDF flag is set. Data written to
 * the ESAI_RSMA affects the next received frame. The frame being received is not affected by this
 * data and would comply to the last ESAI_RSMA setting. Data read from ESAI_RSMA returns the last
 * written data. After hardware or software reset, the ESAI_RSMA register is preset to 0x0000FFFF,
 * which means that all 16 possible slots are enabled for data reception. When operating in normal
 * mode, bit 0 of the ESAI_RSMA register must be set to one, otherwise no input is received.
 */
//@{
#define BP_ESAI_RSMA_RS      (0)      //!< Bit position for ESAI_RSMA_RS.
#define BM_ESAI_RSMA_RS      (0x0000ffff)  //!< Bit mask for ESAI_RSMA_RS.

//! @brief Get value of ESAI_RSMA_RS from a register value.
#define BG_ESAI_RSMA_RS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RSMA_RS) >> BP_ESAI_RSMA_RS)

//! @brief Format value for bitfield ESAI_RSMA_RS.
#define BF_ESAI_RSMA_RS(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RSMA_RS) & BM_ESAI_RSMA_RS)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RS field to a new value.
#define BW_ESAI_RSMA_RS(v)   (HW_ESAI_RSMA_WR((HW_ESAI_RSMA_RD() & ~BM_ESAI_RSMA_RS) | BF_ESAI_RSMA_RS(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_RSMB - Receive Slot Mask Register B
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_RSMB - Receive Slot Mask Register B (RW)
 *
 * Reset value: 0x0000ffff
 *
 * The Receive Slot Mask Register B together with Receive Slot Mask Register A (ESAI_RSMA and
 * ESAI_RSMB) are two read/write registers used by the receiver in network mode to determine for
 * each slot whether to receive a data word and generate a receiver full condition (RDF=1), or to
 * ignore the received data. Fields ESAI_RSMA [RS[15:0]] and ESAI_RSMB [RS31:16]] are concatenated
 * to form the 32-bit field RS[31:0]. Bit number n in RS[31:0] is an enable/disable control bit for
 * receiving data in slot number n.
 */
typedef union _hw_esai_rsmb
{
    reg32_t U;
    struct _hw_esai_rsmb_bitfields
    {
        unsigned RS : 16; //!< [15:0] When bit number N in the ESAI_RSMB register is cleared, the data from the enabled receivers input pins are shifted into their receive shift registers during slot number N.
        unsigned RESERVED0 : 16; //!< [31:16] Reserved
    } B;
} hw_esai_rsmb_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_RSMB register
 */
//@{
#define HW_ESAI_RSMB_ADDR      (REGS_ESAI_BASE + 0xf0)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_RSMB           (*(volatile hw_esai_rsmb_t *) HW_ESAI_RSMB_ADDR)
#define HW_ESAI_RSMB_RD()      (HW_ESAI_RSMB.U)
#define HW_ESAI_RSMB_WR(v)     (HW_ESAI_RSMB.U = (v))
#define HW_ESAI_RSMB_SET(v)    (HW_ESAI_RSMB_WR(HW_ESAI_RSMB_RD() |  (v)))
#define HW_ESAI_RSMB_CLR(v)    (HW_ESAI_RSMB_WR(HW_ESAI_RSMB_RD() & ~(v)))
#define HW_ESAI_RSMB_TOG(v)    (HW_ESAI_RSMB_WR(HW_ESAI_RSMB_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_RSMB bitfields
 */

/*! @name Register ESAI_RSMB, field RS[15:0] (RW)
 *
 * When bit number N in the ESAI_RSMB register is cleared, the data from the enabled receivers input
 * pins are shifted into their receive shift registers during slot number N. The data is not
 * transferred from the receive shift registers to the receive data registers, and neither the RDF
 * nor the ROE flag is set. This means that during a disabled slot, no receiver full interrupt is
 * generated. The Core is interrupted only for enabled slots. When bit number N in the ESAI_RSMB is
 * set, the receive sequence is as usual: data which is shifted into the enabled receivers shift
 * registers is transferred to the receive data registers and the RDF flag is set. Data written to
 * the ESAI_RSMB affects the next received frame. The frame being received is not affected by this
 * data and would comply to the last ESAI_RSMB setting. Data read from ESAI_RSMB returns the last
 * written data. After hardware or software reset, the ESAI_RSMB register is preset to 0x0000FFFF,
 * which means that all 16 possible slots are enabled for data reception.
 */
//@{
#define BP_ESAI_RSMB_RS      (0)      //!< Bit position for ESAI_RSMB_RS.
#define BM_ESAI_RSMB_RS      (0x0000ffff)  //!< Bit mask for ESAI_RSMB_RS.

//! @brief Get value of ESAI_RSMB_RS from a register value.
#define BG_ESAI_RSMB_RS(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_RSMB_RS) >> BP_ESAI_RSMB_RS)

//! @brief Format value for bitfield ESAI_RSMB_RS.
#define BF_ESAI_RSMB_RS(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_RSMB_RS) & BM_ESAI_RSMB_RS)

#ifndef __LANGUAGE_ASM__
//! @brief Set the RS field to a new value.
#define BW_ESAI_RSMB_RS(v)   (HW_ESAI_RSMB_WR((HW_ESAI_RSMB_RD() & ~BM_ESAI_RSMB_RS) | BF_ESAI_RSMB_RS(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_PRRC - Port C Direction Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_PRRC - Port C Direction Register (RW)
 *
 * Reset value: 0x00000000
 *
 * There are two registers to control the ESAI personal reset status: Port C Direction Register
 * (ESAI_PRRC) and Port C Control Register (ESAI_PCRC). The read/write 32-bit Port C Direction
 * Register (ESAI_PRRC) in conjunction with the Port C Control Register (ESAI_PCRC) controls the
 * functionality of the ESAI personal reset state. provides the port pin configurations. Hardware
 * and software reset clear all ESAI_PRRC bits.
 */
typedef union _hw_esai_prrc
{
    reg32_t U;
    struct _hw_esai_prrc_bitfields
    {
        unsigned PDC : 12; //!< [11:0] See .
        unsigned RESERVED0 : 20; //!< [31:12] Reserved
    } B;
} hw_esai_prrc_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_PRRC register
 */
//@{
#define HW_ESAI_PRRC_ADDR      (REGS_ESAI_BASE + 0xf8)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_PRRC           (*(volatile hw_esai_prrc_t *) HW_ESAI_PRRC_ADDR)
#define HW_ESAI_PRRC_RD()      (HW_ESAI_PRRC.U)
#define HW_ESAI_PRRC_WR(v)     (HW_ESAI_PRRC.U = (v))
#define HW_ESAI_PRRC_SET(v)    (HW_ESAI_PRRC_WR(HW_ESAI_PRRC_RD() |  (v)))
#define HW_ESAI_PRRC_CLR(v)    (HW_ESAI_PRRC_WR(HW_ESAI_PRRC_RD() & ~(v)))
#define HW_ESAI_PRRC_TOG(v)    (HW_ESAI_PRRC_WR(HW_ESAI_PRRC_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_PRRC bitfields
 */

/*! @name Register ESAI_PRRC, field PDC[11:0] (RW)
 *
 * See .
 */
//@{
#define BP_ESAI_PRRC_PDC      (0)      //!< Bit position for ESAI_PRRC_PDC.
#define BM_ESAI_PRRC_PDC      (0x00000fff)  //!< Bit mask for ESAI_PRRC_PDC.

//! @brief Get value of ESAI_PRRC_PDC from a register value.
#define BG_ESAI_PRRC_PDC(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_PRRC_PDC) >> BP_ESAI_PRRC_PDC)

//! @brief Format value for bitfield ESAI_PRRC_PDC.
#define BF_ESAI_PRRC_PDC(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_PRRC_PDC) & BM_ESAI_PRRC_PDC)

#ifndef __LANGUAGE_ASM__
//! @brief Set the PDC field to a new value.
#define BW_ESAI_PRRC_PDC(v)   (HW_ESAI_PRRC_WR((HW_ESAI_PRRC_RD() & ~BM_ESAI_PRRC_PDC) | BF_ESAI_PRRC_PDC(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// HW_ESAI_PCRC - Port C Control Register
//-------------------------------------------------------------------------------------------

#ifndef __LANGUAGE_ASM__
/*!
 * @brief HW_ESAI_PCRC - Port C Control Register (RW)
 *
 * Reset value: 0x00000000
 *
 * The read/write 32-bit Port C Control Register (ESAI_PCRC) in conjunction with the Port C
 * Direction Register (ESAI_PRRC) controls the functionality of the ESAI personal reset state. Each
 * of the PC(11:0) bits controls the functionality of the corresponding port pin. provides the port
 * pin configurations. Hardware and software reset clear all ESAI_PCRC bits. PCRC and PRRC Bits
 * Functionality PDC[i] PC[i] Port Pin[i] Function 0 0 Disconnected 1 1 ESAI
 */
typedef union _hw_esai_pcrc
{
    reg32_t U;
    struct _hw_esai_pcrc_bitfields
    {
        unsigned PC : 12; //!< [11:0] See .
        unsigned RESERVED0 : 20; //!< [31:12] Reserved
    } B;
} hw_esai_pcrc_t;
#endif

/*!
 * @name Constants and macros for entire ESAI_PCRC register
 */
//@{
#define HW_ESAI_PCRC_ADDR      (REGS_ESAI_BASE + 0xfc)

#ifndef __LANGUAGE_ASM__
#define HW_ESAI_PCRC           (*(volatile hw_esai_pcrc_t *) HW_ESAI_PCRC_ADDR)
#define HW_ESAI_PCRC_RD()      (HW_ESAI_PCRC.U)
#define HW_ESAI_PCRC_WR(v)     (HW_ESAI_PCRC.U = (v))
#define HW_ESAI_PCRC_SET(v)    (HW_ESAI_PCRC_WR(HW_ESAI_PCRC_RD() |  (v)))
#define HW_ESAI_PCRC_CLR(v)    (HW_ESAI_PCRC_WR(HW_ESAI_PCRC_RD() & ~(v)))
#define HW_ESAI_PCRC_TOG(v)    (HW_ESAI_PCRC_WR(HW_ESAI_PCRC_RD() ^  (v)))
#endif
//@}

/*
 * constants & macros for individual ESAI_PCRC bitfields
 */

/*! @name Register ESAI_PCRC, field PC[11:0] (RW)
 *
 * See .
 */
//@{
#define BP_ESAI_PCRC_PC      (0)      //!< Bit position for ESAI_PCRC_PC.
#define BM_ESAI_PCRC_PC      (0x00000fff)  //!< Bit mask for ESAI_PCRC_PC.

//! @brief Get value of ESAI_PCRC_PC from a register value.
#define BG_ESAI_PCRC_PC(r)   ((__REG_VALUE_TYPE((r), reg32_t) & BM_ESAI_PCRC_PC) >> BP_ESAI_PCRC_PC)

//! @brief Format value for bitfield ESAI_PCRC_PC.
#define BF_ESAI_PCRC_PC(v)   ((__REG_VALUE_TYPE((v), reg32_t) << BP_ESAI_PCRC_PC) & BM_ESAI_PCRC_PC)

#ifndef __LANGUAGE_ASM__
//! @brief Set the PC field to a new value.
#define BW_ESAI_PCRC_PC(v)   (HW_ESAI_PCRC_WR((HW_ESAI_PCRC_RD() & ~BM_ESAI_PCRC_PC) | BF_ESAI_PCRC_PC(v)))
#endif
//@}

//-------------------------------------------------------------------------------------------
// hw_esai_t - module struct
//-------------------------------------------------------------------------------------------
/*!
 * @brief All ESAI module registers.
 */
#ifndef __LANGUAGE_ASM__
#pragma pack(1)
typedef struct _hw_esai
{
    volatile hw_esai_etdr_t ETDR; //!< ESAI Transmit Data Register
    volatile hw_esai_erdr_t ERDR; //!< ESAI Receive Data Register
    volatile hw_esai_ecr_t ECR; //!< ESAI Control Register
    volatile hw_esai_esr_t ESR; //!< ESAI Status Register
    volatile hw_esai_tfcr_t TFCR; //!< Transmit FIFO Configuration Register
    volatile hw_esai_tfsr_t TFSR; //!< Transmit FIFO Status Register
    volatile hw_esai_rfcr_t RFCR; //!< Receive FIFO Configuration Register
    volatile hw_esai_rfsr_t RFSR; //!< Receive FIFO Status Register
    reg32_t _reserved0[24];
    volatile hw_esai_txn_t TXn[6]; //!< Transmit Data Register n
    volatile hw_esai_tsr_t TSR; //!< ESAI Transmit Slot Register
    reg32_t _reserved1;
    volatile hw_esai_rxn_t RXn[4]; //!< Receive Data Register n
    reg32_t _reserved2[7];
    volatile hw_esai_saisr_t SAISR; //!< Serial Audio Interface Status Register
    volatile hw_esai_saicr_t SAICR; //!< Serial Audio Interface Control Register
    volatile hw_esai_tcr_t TCR; //!< Transmit Control Register
    volatile hw_esai_tccr_t TCCR; //!< Transmit Clock Control Register
    volatile hw_esai_rcr_t RCR; //!< Receive Control Register
    volatile hw_esai_rccr_t RCCR; //!< Receive Clock Control Register
    volatile hw_esai_tsma_t TSMA; //!< Transmit Slot Mask Register A
    volatile hw_esai_tsmb_t TSMB; //!< Transmit Slot Mask Register B
    volatile hw_esai_rsma_t RSMA; //!< Receive Slot Mask Register A
    volatile hw_esai_rsmb_t RSMB; //!< Receive Slot Mask Register B
    reg32_t _reserved3;
    volatile hw_esai_prrc_t PRRC; //!< Port C Direction Register
    volatile hw_esai_pcrc_t PCRC; //!< Port C Control Register
} hw_esai_t;
#pragma pack()

//! @brief Macro to access all ESAI registers.
//! @return Reference (not a pointer) to the registers struct. To get a pointer to the struct,
//!     use the '&' operator, like <code>&HW_ESAI</code>.
#define HW_ESAI     (*(hw_esai_t *) REGS_ESAI_BASE)
#endif

#endif // __HW_ESAI_REGISTERS_H__
// v18/121106/1.2.2
// EOF