/* generated HAL source file - do not edit */
#include "hal_data.h"

scif_uart_instance_ctrl_t g_uart2_ctrl;

scif_baud_setting_t g_uart2_baud_setting =
{
    /* Baud rate calculated with 0.469% error. */ 
    .abcs = 0,
    .bgdm = 1,
    .cks = 0,
    .brr = 53,
    .mddr = (uint8_t)256,
    .brme = false
};

/** UART extended configuration for UARTonSCIF HAL driver */
const scif_uart_extended_cfg_t g_uart2_cfg_extend =
{
    .bri_ipl = 14,
    .bri_irq = SCIF2_BRK_IRQn,
    .clock = SCIF_UART_CLOCK_INT,
    .noise_cancel = SCIF_UART_NOISE_CANCELLATION_DISABLE,
    .p_baud_setting = &g_uart2_baud_setting,
    .rx_fifo_trigger = SCIF_UART_RECEIVE_TRIGGER_MAX,
    .rts_fifo_trigger = SCIF_UART_RTS_TRIGGER_14,
    .uart_mode = SCIF_UART_MODE_RS232,
    .flow_control = SCIF_UART_FLOW_CONTROL_NONE,
    .driver_enable_pin = (bsp_io_port_pin_t)SCIF_UART_INVALID_16BIT_PARAM,
};

/** UART interface configuration */
const uart_cfg_t g_uart2_cfg =
{
    .channel = 2,
    .data_bits = UART_DATA_BITS_8,
    .parity = UART_PARITY_OFF,
    .stop_bits = UART_STOP_BITS_1,
    .p_callback = NULL,
    .p_context = NULL,
    .p_extend = &g_uart2_cfg_extend,
    .p_transfer_tx = NULL,
    .p_transfer_rx = NULL,
    .rxi_ipl = 14,
    .txi_ipl = 14,
    .tei_ipl = 14,
    .eri_ipl = 14,
    .rxi_irq = SCIF2_RXI_IRQn,
    .txi_irq = SCIF2_TXI_IRQn,
    .tei_irq = SCIF2_TEI_DRI_IRQn,
    .eri_irq = SCIF2_RERR_IRQn,
};

/* Instance structure to use this module. */
const uart_instance_t g_uart2 =
{
    .p_ctrl = &g_uart2_ctrl, 
    .p_cfg = &g_uart2_cfg, 
    .p_api = &g_uart_on_scif
};

gtm_instance_ctrl_t g_timer2_ctrl;

const gtm_extended_cfg_t g_timer2_extend =
{
    .generate_interrupt_when_starts = GTM_GIWS_TYPE_DISABLED,
    .gtm_mode = GTM_TIMER_MODE_INTERVAL,
};

const timer_cfg_t g_timer2_cfg =
{
    .mode = TIMER_MODE_PERIODIC,
    // .period_counts = 99999 /* Actual period: 0.001 seconds. */,
    .period_counts = 100000000 /* Actual period: 0.001 seconds. */,
    .channel = 2,
    .p_callback = NULL,
    .p_context = NULL,
    .cycle_end_ipl = 255,
    .p_extend = &g_timer2_extend,
#if defined(VECTOR_NUMBER_GTM2_COUNTER_OVERFLOW)
    .cycle_end_irq = VECTOR_NUMBER_GTM2_COUNTER_OVERFLOW,
#else
    .cycle_end_irq = GTM2_OSTM2INT_IRQn,
#endif
};

/* Instance structure to use this module. */
const timer_instance_t g_timer2 =
{
    .p_ctrl = &g_timer2_ctrl, 
    .p_cfg = &g_timer2_cfg, 
    .p_api = &g_timer_on_gtm
};

void g_hal_init(void)
{
    g_common_init();
}