move aiit-arm32-board and aiit-riscv64-board to aiit_board

2022-03-04 14:48:58 +08:00
parent 96ecc0324f
commit a5f48c65b7
118 changed files with 9 additions and 2 deletions
@@ -0,0 +1,141 @@
+/****************************************************************************
+ * boards/arm/stm32/aiit-arm32-board/src/stm32_ug2864ambag01.c
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <debug.h>
+
+#include <nuttx/board.h>
+#include <nuttx/spi/spi.h>
+#include <nuttx/lcd/lcd.h>
+#include <nuttx/lcd/ug-2864ambag01.h>
+
+#include "stm32_gpio.h"
+#include "stm32_spi.h"
+
+#include "aiit-arm32-board.h"
+
+#ifdef CONFIG_LCD_UG2864AMBAG01
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+/* The pin configurations here require that SPI1 is selected */
+
+#ifndef CONFIG_STM32_SPI1
+#  error "The OLED driver requires CONFIG_STM32_SPI1 in the configuration"
+#endif
+
+#ifndef CONFIG_SPI_CMDDATA
+#  error "The OLED driver requires CONFIG_SPI_CMDDATA in the configuration"
+#endif
+
+/* Pin Configuration ********************************************************/
+
+/* UG-2864AMBAG01 OLED Display (SPI 4-wire):
+ *
+ * --------------------------+----------------------------------------------
+ * Connector CON10 J1:      | STM32F4Discovery
+ * --------------+-----------+----------------------------------------------
+ * CON10 J1:     | CON20 J2: | P1/P2:
+ * --------------+-----------+----------------------------------------------
+ * 1  3v3        | 3,4 3v3   | P2 3V
+ * 3  /RESET     | 8 /RESET  | P2 PB6 (Arbitrary selection)
+ * 5  /CS        | 7 /CS     | P2 PB7 (Arbitrary selection)(2)
+ * 7  A0         | 9 A0      | P2 PB8 (Arbitrary selection)(2)
+ * 9  LED+ (N/C) | -----     | -----
+ * 2  5V Vcc     | 1,2 Vcc   | P2 5V
+ * 4  DI         | 18 D1/SI  | P1 PA7 (GPIO_SPI1_MOSI==GPIO_SPI1_MOSI_1 (1))
+ * 6  SCLK       | 19 D0/SCL | P1 PA5 (GPIO_SPI1_SCK==GPIO_SPI1_SCK_1 (2))
+ * 8  LED- (N/C) | -----     | ------
+ * 10 GND        | 20 GND    | P2 GND
+ * --------------+-----------+----------------------------------------------
+ * (1) Required because of on-board MEMS
+ * (2) Note that the OLED CS and A0 are managed in the stm32_spi.c file.
+ * -------------------------------------------------------------------------
+ */
+
+/* Definitions in aiit-arm32-board.h */
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_graphics_setup
+ *
+ * Description:
+ *   Called by NX initialization logic to configure the OLED.
+ *
+ ****************************************************************************/
+
+FAR struct lcd_dev_s *board_graphics_setup(unsigned int devno)
+{
+  FAR struct spi_dev_s *spi;
+  FAR struct lcd_dev_s *dev;
+
+  /* Configure the OLED GPIOs. This initial configuration is RESET low,
+   * putting the OLED into reset state.
+   */
+
+  stm32_configgpio(GPIO_OLED_RESET);
+
+  /* Wait a bit then release the OLED from the reset state */
+
+  up_mdelay(20);
+  stm32_gpiowrite(GPIO_OLED_RESET, true);
+
+  /* Get the SPI1 port interface */
+
+  spi = stm32_spibus_initialize(1);
+  if (!spi)
+    {
+      lcderr("ERROR: Failed to initialize SPI port 1\n");
+    }
+  else
+    {
+      /* Bind the SPI port to the OLED */
+
+      dev = ug2864ambag01_initialize(spi, devno);
+      if (!dev)
+        {
+          lcderr("ERROR: Failed to bind SPI port 1 to OLED %d\n", devno);
+        }
+     else
+        {
+          lcdinfo("Bound SPI port 1 to OLED %d\n", devno);
+
+          /* And turn the OLED on */
+
+          dev->setpower(dev, CONFIG_LCD_MAXPOWER);
+          return dev;
+        }
+    }
+
+  return NULL;
+}
+#endif /* CONFIG_LCD_UG2864AMBAG01 */