diff --git a/APP_Framework/Framework/connection/4g/ec200t/ec200t.c b/APP_Framework/Framework/connection/4g/ec200t/ec200t.c index 3e8f38508..456f05664 100644 --- a/APP_Framework/Framework/connection/4g/ec200t/ec200t.c +++ b/APP_Framework/Framework/connection/4g/ec200t/ec200t.c @@ -163,6 +163,8 @@ static int Ec200tIoctl(struct Adapter *adapter, int cmd, void *args) serial_cfg.serial_parity_mode = PARITY_NONE; serial_cfg.serial_bit_order = STOP_BITS_1; serial_cfg.serial_invert_mode = NRZ_NORMAL; + //serial receive timeout 10s + serial_cfg.serial_timeout = 10000; serial_cfg.is_ext_uart = 0; #ifdef ADAPTER_EC200T_DRIVER_EXT_PORT serial_cfg.is_ext_uart = 1; diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board.h b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board.h index 405566e68..3693cb79c 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board.h +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board.h @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/include/board.h - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file board.h + * @brief sabre-lite board.h file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ #ifndef __BOARDS_ARM_IMX6_SABRE_LITE_INCLUDE_BOARD_H #define __BOARDS_ARM_IMX6_SABRE_LITE_INCLUDE_BOARD_H diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board_memorymap.h b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board_memorymap.h index d49e77662..14fa834cf 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board_memorymap.h +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/include/board_memorymap.h @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/include/board_memorymap.h - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file board_memorymap.h + * @brief sabre-lite board memorymap + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ #ifndef __BOARDS_ARM_IMX6_SABRE_LITE_INCLUDE_BOARD_MEMORYMAP_H #define __BOARDS_ARM_IMX6_SABRE_LITE_INCLUDE_BOARD_MEMORYMAP_H diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_appinit.c b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_appinit.c index a90b2913a..26c471a34 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_appinit.c +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_appinit.c @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/src/imx_appinit.c - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file imx_appinit.c + * @brief sabre-lite imx_appinit.c file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ /**************************************************************************** * Included Files diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_autoleds.c b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_autoleds.c index ab081c440..cfd34ca69 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_autoleds.c +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_autoleds.c @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/src/imx_autoleds.c - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file imx_autoleds.c + * @brief sabre-lite imx_autoleds.c file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ /* LEDs * diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_boardinit.c b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_boardinit.c index df29c3b07..3f49cef5c 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_boardinit.c +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_boardinit.c @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/src/imx_boardinit.c - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file imx_boardinit.c + * @brief sabre-lite imx_boardinit.c file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ /**************************************************************************** * Included Files diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_bringup.c b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_bringup.c index b26bf4582..71e55b8b2 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_bringup.c +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_bringup.c @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/src/imx_bringup.c - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file imx_bringup.c + * @brief sabre-lite imx_bringup.c file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ /**************************************************************************** * Included Files diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_userleds.c b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_userleds.c index f86268f1c..2261bf165 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_userleds.c +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/imx_userleds.c @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/src/imx_userleds.c - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file imx_userleds.c + * @brief sabre-lite imx_userleds.c file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ /**************************************************************************** * Included Files diff --git a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/sabre-lite.h b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/sabre-lite.h index 76568b434..f4b310767 100644 --- a/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/sabre-lite.h +++ b/Ubiquitous/Nuttx_Fusion_XiUOS/aiit_board/sabre-lite/src/sabre-lite.h @@ -1,22 +1,22 @@ -/**************************************************************************** - * boards/arm/imx6/sabre-lite/src/sabre-lite.h - * - * Licensed to the Apache Software Foundation (ASF) under one or more - * contributor license agreements. See the NOTICE file distributed with - * this work for additional information regarding copyright ownership. The - * ASF licenses this file to you under the Apache License, Version 2.0 (the - * "License"); you may not use this file except in compliance with the - * License. You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT - * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the - * License for the specific language governing permissions and limitations - * under the License. - * - ****************************************************************************/ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** + * @file sabre-lite.h + * @brief sabre-lite sabre-lite.h file + * @version 1.0 + * @author AIIT XUOS Lab + * @date 2023.05.15 + */ #ifndef __BOARDS_ARM_IMX6_SABRE_LITE_SRC_SABRE_LITE_H #define __BOARDS_ARM_IMX6_SABRE_LITE_SRC_SABRE_LITE_H diff --git a/Ubiquitous/XiZi_AIoT/softkernel/task/Makefile b/Ubiquitous/XiZi_AIoT/softkernel/task/Makefile index 4ca20e597..93ec6f896 100644 --- a/Ubiquitous/XiZi_AIoT/softkernel/task/Makefile +++ b/Ubiquitous/XiZi_AIoT/softkernel/task/Makefile @@ -1,3 +1,3 @@ -SRC_FILES := task.c schedule.c ipc.c +SRC_FILES := schedule.c ipc.c include $(KERNEL_ROOT)/compiler.mk diff --git a/Ubiquitous/XiZi_AIoT/softkernel/task/ipc.c b/Ubiquitous/XiZi_AIoT/softkernel/task/ipc.c deleted file mode 100644 index e69de29bb..000000000 diff --git a/Ubiquitous/XiZi_AIoT/softkernel/task/schedule.c b/Ubiquitous/XiZi_AIoT/softkernel/task/schedule.c deleted file mode 100644 index e69de29bb..000000000 diff --git a/Ubiquitous/XiZi_AIoT/softkernel/task/task.c b/Ubiquitous/XiZi_AIoT/softkernel/task/task.c index e69de29bb..808804462 100644 --- a/Ubiquitous/XiZi_AIoT/softkernel/task/task.c +++ b/Ubiquitous/XiZi_AIoT/softkernel/task/task.c @@ -0,0 +1,537 @@ + +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiUOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** +* @file: task.c +* @brief: file task.c +* @version: 1.0 +* @author: AIIT XUOS Lab +* @date: 2023/05/18 +* +*/ + +#include + + +// 全局运行队列和本地运行队列 +tcb_t *global_run_queue_head = NULL; +tcb_t *global_run_queue_tail = NULL; +tcb_t *local_run_queue_head[8] = {NULL}; +tcb_t *local_run_queue_tail[8] = {NULL}; + +// 当前任务的指针 +volatile tcb_t *current_task = NULL; + + +/******************************************************************************* +* 函 数 名: tcb_init +* 功能描述: 初始化任务控制块 +* 形 参: tcb:任务控制块指针,priority:任务优先级,stack_size:栈大小 +* 返 回 值: 无 +*******************************************************************************/ +void tcb_init(tcb_t *tcb, int priority, int stack_size) { + tcb->priority = priority; + tcb->state = TASK_CREATED; + tcb->message_queue = NULL; + tcb->stack = (uint8_t*)malloc(stack_size); + tcb->stack_size = stack_size; + tcb->stack_ptr = tcb->stack + stack_size - sizeof(context_t); + // 将任务的上下文保存在栈中 + context_t *context = (context_t*)tcb->stack_ptr; + context_init(context, (void*)task_entry, tcb->stack_ptr); +} + +/******************************************************************************* +* 函 数 名: tcb_destroy +* 功能描述: 销毁任务控制块 +* 形 参: tcb:任务控制块指针 +* 返 回 值: 无 +*******************************************************************************/ +void tcb_destroy(tcb_t *tcb) { + free(tcb->stack_bottom); + tcb->stack_ptr = NULL; + tcb->stack_bottom = NULL; + tcb->stack_size = 0; + tcb->state = TASK_BLOCKED; + tcb->priority = 0; + tcb->next = NULL; + if (tcb->message_queue != NULL) { + message_queue_destroy(tcb->message_queue); + tcb->message_queue = NULL; + } +} + +/******************************************************************************* +* 函 数 名: get_current_task +* 功能描述: 获取当前任务的指针 +* 形 参: 无 +* 返 回 值: 任务控制块指针 +*******************************************************************************/ +tcb_t *get_current_task() { + return (tcb_t*)current_task; +} + + +/******************************************************************************* +* 函 数 名: get_local_run_queue_head +* 功能描述: 获取本地运行队列的头指针 +* 形 参: cpu_id:当前cpu的id +* 返 回 值: 任务控制块指针 +*******************************************************************************/ +tcb_t *get_local_run_queue_head(int cpu_id) { + return local_run_queue_head[cpu_id]; +} + + +/******************************************************************************* +* 函 数 名: add_to_global_run_queue +* 功能描述: 将任务添加到全局运行队列中 +* 形 参: tcb:任务控制块指针 +* 返 回 值: 无 +*******************************************************************************/ +void add_to_global_run_queue(tcb_t *tcb) { + // 将任务添加到全局运行队列的尾部 + if (global_run_queue_head == NULL) { + global_run_queue_head = tcb; + global_run_queue_tail = tcb; + } else { + global_run_queue_tail->next = tcb; + global_run_queue_tail = tcb; + } +} + + +/******************************************************************************* +* 函 数 名: take_from_global_run_queue +* 功能描述: 从全局运行队列中取出一个任务 +* 形 参: 无 +* 返 回 值: tcb:任务控制块指针 +*******************************************************************************/ +tcb_t *take_from_global_run_queue() { + // 从全局运行队列的头部取出一个任务 + if (global_run_queue_head == NULL) { + return NULL; + } else { + tcb_t *tcb = global_run_queue_head; + global_run_queue_head = tcb->next; + if (global_run_queue_head == NULL) { + global_run_queue_tail = NULL; + } + return tcb; + } +} + + +/******************************************************************************* +* 函 数 名: add_to_local_run_queue +* 功能描述: 将任务添加到本地运行队列中 +* 形 参: tcb:任务控制块指针,cpu_id:任务绑定的CPU id +* 返 回 值: 无 +*******************************************************************************/ +void add_to_local_run_queue(tcb_t *tcb, int cpu_id) { + // 将任务添加到本地运行队列的尾部 + if (local_run_queue_head[cpu_id] == NULL) { + local_run_queue_head[cpu_id] = tcb; + local_run_queue_tail[cpu_id] = tcb; + } else { + local_run_queue_tail[cpu_id]->next = tcb; + local_run_queue_tail[cpu_id] = tcb; + } +} + + +/******************************************************************************* +* 函 数 名: take_from_local_run_queue +* 功能描述: 从本地运行队列中取出一个任务 +* 形 参: cpu_id:CPU id +* 返 回 值: 无 +*******************************************************************************/ +tcb_t *take_from_local_run_queue(int cpu_id) { + // 从本地运行队列的头部取出一个任务 + if (local_run_queue_head[cpu_id] == NULL) { + return NULL; + } else { + tcb_t *tcb = local_run_queue_head[cpu_id]; + local_run_queue_head[cpu_id] = tcb->next; + if (local_run_queue_head[cpu_id] == NULL) { + local_run_queue_tail[cpu_id] = NULL; + } + return tcb; + } +} + + +/******************************************************************************* +* 函 数 名: move_current_task_to_global_run_queue +* 功能描述: 将当前任务从本地运行队列中取出,并添加到全局运行队列中 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void move_current_task_to_global_run_queue() { + int cpu_id = get_cpu_id(); + tcb_t *tcb = (tcb_t*)current_task; + tcb->state = TASK_READY; + add_to_global_run_queue(tcb); + local_run_queue_head[cpu_id] = NULL; + local_run_queue_tail[cpu_id] = NULL; + current_task = NULL; +} + + +/******************************************************************************* +* 函 数 名: switch_to_next_task +* 功能描述: 切换到下一个任务 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void switch_to_next_task() { + int cpu_id = get_cpu_id(); + tcb_t *current_tcb = (tcb_t*)current_task; + tcb_t *next_tcb = take_from_local_run_queue(cpu_id); + if (next_tcb == NULL) { + next_tcb = take_from_global_run_queue(); + } + if (next_tcb == NULL) { + // 如果没有可运行的任务，则将当前任务继续运行 + return; + } + // 保存当前任务的上下文 + if (current_tcb != NULL) { + current_tcb->stack_ptr = get_stack_pointer(); + } + // 切换到下一个任务的上下文 + current_task = next_tcb; + set_stack_pointer(next_tcb->stack_ptr); + // 如果切换到的任务是新的任务，需要执行任务初始化函数 + if (current_tcb != next_tcb) { + next_tcb->state = TASK_RUNNING; + task_init(next_tcb); + } +} + + +/******************************************************************************* +* 函 数 名: task_init +* 功能描述: 任务初始化函数 +* 形 参: tcb:任务控制块指针 +* 返 回 值: 无 +*******************************************************************************/ +void task_init(tcb_t *tcb) { + // 创建消息队列 + message_queue_t mq = (message_queue_t)malloc(sizeof(message_queue_t)); + mq->buffer = (message_t)malloc(sizeof(message_t) * 16); + mq->capacity = 16; + mq->head = 0; + mq->tail = 0; + mq->count = 0; + tcb->message_queue = mq; +} + + +/******************************************************************************* +* 函 数 名: create_task +* 功能描述: 创建任务 +* 形 参: priority:任务优先级,stack_size:栈大小 +* 返 回 值: 无 +*******************************************************************************/ +tcb_t *create_task(int priority, int stack_size) { + tcb_t *tcb = (tcb_t*)malloc(sizeof(tcb_t)); + tcb_init(tcb, priority, stack_size); + add_to_global_run_queue(tcb); + return tcb; +} + + +/******************************************************************************* +* 函 数 名: destroy_task +* 功能描述: 销毁任务 +* 形 参: tcb:任务控制块指针 +* 返 回 值: 无 +*******************************************************************************/ +void destroy_task(tcb_t *tcb) { + tcb_destroy(tcb); + free(tcb); +} + + +/******************************************************************************* +* 函 数 名: send_message +* 功能描述: 发送消息 +* 形 参: dest_tcb:目标任务的控制块指针,type:消息类型,data:消息的具体内容 +* 返 回 值: 无 +*******************************************************************************/ +void send_message(tcb_t *dest_tcb, int type, void *data) { + message_t message; + message.type = type; + message.data = data; + if (dest_tcb->message_queue == NULL) { + // 如果目标任务没有消息队列，则创建一个消息队列 + dest_tcb->message_queue = message_queue_create(16); + } + // 将消息添加到目标任务的消息队列中 + message_queue_push(dest_tcb->message_queue, &message); +} + + +/******************************************************************************* +* 函 数 名: receive_message +* 功能描述: 接收消息 +* 形 参: type:接收的消息类型,data:存储接收到的消息 +* 返 回 值: 无 +*******************************************************************************/ +void receive_message(int type, void *data) { + tcb_t *current_tcb = (tcb_t*)current_task; + message_t message; + // 从当前任务的消息队列中取出消息 + while (message_queue_pop(current_tcb->message_queue, &message) != 0) { + if (message.type == type) { + // 如果消息的类型匹配，则返回消息数据 + memcpy(data, message.data, sizeof(void*)); + return; + } + } + // 如果没有匹配的消息，则当前任务被阻塞，直到有匹配的消息为止 + current_tcb->state = TASK_BLOCKED; + while (message_queue_pop(current_tcb->message_queue, &message) != 0) { + if (message.type == type) { + // 如果有匹配的消息，则返回消息数据，并将当前任务状态设置为就绪 + memcpy(data, message.data, sizeof(void*)); + current_tcb->state = TASK_READY; + return; + } + } + // 如果还是没有匹配的消息，则当前任务一直被阻塞 + while (1) { + wait_for_interrupt(); + } +} + + +/******************************************************************************* +* 函 数 名: message_queue_create +* 功能描述: 创建消息队列 +* 形 参: capacity:消息队列的容量 +* 返 回 值: 生成的消息队列的指针 +*******************************************************************************/ +message_queue_t *message_queue_create(int capacity) { + message_queue_t *mq = (message_queue_t*)malloc(sizeof(message_queue_t)); + mq->buffer = (message_t*)malloc(sizeof(message_t) * capacity); + mq->capacity = capacity; + mq->head = 0; + mq->tail = 0; + mq->count = 0; + return mq; +} + + +/******************************************************************************* +* 函 数 名: message_queue_destroy +* 功能描述: 销毁消息队列 +* 形 参: mq:消息队列的指针 +* 返 回 值: 无 +*******************************************************************************/ +void message_queue_destroy(message_queue_t *mq) { + free(mq->buffer); + free(mq); +} + + +/******************************************************************************* +* 函 数 名: message_queue_push +* 功能描述: 将消息添加到消息队列中 +* 形 参: message_queue_t:消息队列的指针,message_t:存储的消息 +* 返 回 值: 0:成功,-1:失败 +*******************************************************************************/ +int message_queue_push(message_queue_t *mq, message_t *message) { + if (mq->count >= mq->capacity) { + return -1; // 队列已满 + } + mq->buffer[mq->tail] = *message; + mq->tail = (mq->tail + 1) % mq->capacity; + mq->count++; + return 0; +} + + +/******************************************************************************* +* 函 数 名: message_queue_pop +* 功能描述: 从消息队列中取出消息 +* 形 参: message_queue_t:消息队列的指针,message_t:存储的消息 +* 返 回 值: 0:成功,-1:失败 +*******************************************************************************/ +int message_queue_pop(message_queue_t *mq, message_t *message) { + if (mq->count <= 0) { + return -1; // 队列已空 + } + *message = mq->buffer[mq->head]; + mq->head = (mq->head + 1) % mq->capacity; + mq->count--; + return 0; +} + + +/******************************************************************************* +* 函 数 名: context_init +* 功能描述: 初始化上下文 +* 形 参: message_queue_t:消息队列的指针,message_t:存储的消息 +* 返 回 值: 0:成功,-1:失败 +*******************************************************************************/ +void context_init(context_t *context, void (*entry)(void), void *stack_ptr) { + context->cpsr = 0x10; // 设置 CPSR 的初始值 + context->pc = (uint32_t)entry; // 设置 PC 的初始值为任务入口地址 + context->r0 = (uint32_t)stack_ptr; // 设置 R0 的初始值为栈指针 + context->r1 = 0; // 设置 R1 的初始值为 0 + context->r2 = 0; // 设置 R2 的初始值为 0 + context->r3 = 0; // 设置 R3 的初始值为 0 + context->r4 = 0; // 设置 R4 的初始值为 0 + context->r5 = 0; // 设置 R5 的初始值为 0 + context->r6 = 0; // 设置 R6 的初始值为 0 + context->r7 = 0; // 设置 R7 的初始值为 0 + context->r8 = 0; // 设置 R8 的初始值为 0 + context->r9 = 0; // 设置 R9 的初始值为 0 + context->r10 = 0; // 设置 R10 的初始值为 0 + context->r11 = 0; // 设置 R11 的初始值为 0 + context->r12 = 0; // 设置 R12 的初始值为 0 + context->sp = (uint32_t)stack_ptr; // 设置 SP 的初始值为栈指针 + context->lr = (uint32_t)task_exit; // 设置 LR 的初始值为线程退出函数的地址 +} + +/******************************************************************************* +* 函 数 名: wait_for_interrupt +* 功能描述: 等待中断 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void wait_for_interrupt() { + // 在实现中，可以使用 WFI 指令等待中断 + __asm__ volatile("wfi"); +} + +/******************************************************************************* +* 函 数 名: get_cpu_id +* 功能描述: 获取CPU id +* 形 参: 无 +* 返 回 值: 获取的cpu id +*******************************************************************************/ +int get_cpu_id() { + uint32_t mpidr; + __asm__ volatile("mrc p15, 0, %0, c0, c0, 5" : "=r"(mpidr)); + return mpidr & 0xff; +} + + +/******************************************************************************* +* 函 数 名: get_stack_pointer +* 功能描述: 获取栈指针 +* 形 参: 无 +* 返 回 值: 获取到的栈指针 +*******************************************************************************/ +void *get_stack_pointer() { + // 在实现中，可以使用 ARM 的 SP 寄存器获取栈指针 + void *sp; + __asm__ volatile("mov %0, sp" : "=r"(sp)); + return sp; +} + + +/******************************************************************************* +* 函 数 名: set_stack_pointer +* 功能描述: 设置栈指针 +* 形 参: 设置的栈指针 +* 返 回 值: 无 +*******************************************************************************/ +void set_stack_pointer(void *sp) { + // 在实现中，可以使用 ARM 的 SP 寄存器设置栈指针 + __asm__ volatile("mov sp, %0" : : "r"(sp)); +} + +/******************************************************************************* +* 函 数 名: add_interrupt_handler +* 功能描述: 添加中断处理函数 +* 形 参: irq:中断号,handler:中断句柄,priority:中断优先级 +* 返 回 值: 无 +*******************************************************************************/ +void add_interrupt_handler(int irq, void (*handler)(void), int priority) { + uint32_t *vector_table = (uint32_t*)0x0; + + // 将中断处理函数写入中断向量表中 + vector_table[irq + 16] = (uint32_t)handler; + + // 设置中断优先级 + uint8_t priority_shift = 8 - __NVIC_PRIO_BITS; + uint32_t priority_mask = 0xff << priority_shift; + uint32_t priority_value = (priority << priority_shift) & priority_mask; + uint32_t *priority_reg = (uint32_t*)0xE000E400; + int index = irq / 4; + int offset = irq % 4; + priority_reg[index] &= ~(0xff << (offset * 8)); + priority_reg[index] |= (priority_value << (offset * 8)); + + // 使能中断 + uint32_t *enable_reg = (uint32_t*)0xE000E100; + enable_reg[irq / 32] |= 1 << (irq % 32); +} + + +/******************************************************************************* +* 函 数 名: enter_critical +* 功能描述: 进入临界区 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void enter_critical() { + // 在实现中，可以使用 ARM 的 CPSR 寄存器进入临界区 + __asm__ volatile("cpsid i"); +} + +/******************************************************************************* +* 函 数 名: leave_critical +* 功能描述: 离开临界区 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void leave_critical() { + // 在实现中，可以使用 ARM 的 CPSR 寄存器离开临界区 + __asm__ volatile("cpsie i"); +} + + + +/******************************************************************************* +* 函 数 名: task_exit +* 功能描述: 任务退出函数 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void task_exit() { + // 切换到下一个任务 + switch_to_next_task(); + // 在实现中，可以使用 ARM 的 WFE 指令等待下一个中断 + __asm__ volatile("wfe"); +} + + +/******************************************************************************* +* 函 数 名: task_entry +* 功能描述: 任务入口函数 +* 形 参: 无 +* 返 回 值: 无 +*******************************************************************************/ +void task_entry() { + tcb_t *current_tcb = (tcb_t*)current_task; + current_tcb->state = TASK_RUNNING; + task_init(current_tcb); + while (1) { + switch_to_next_task(); + } +} diff --git a/Ubiquitous/XiZi_AIoT/softkernel/task/task.h b/Ubiquitous/XiZi_AIoT/softkernel/task/task.h new file mode 100644 index 000000000..fdcc38fa0 --- /dev/null +++ b/Ubiquitous/XiZi_AIoT/softkernel/task/task.h @@ -0,0 +1,135 @@ +/* +* Copyright (c) 2020 AIIT XUOS Lab +* XiUOS is licensed under Mulan PSL v2. +* You can use this software according to the terms and conditions of the Mulan PSL v2. +* You may obtain a copy of Mulan PSL v2 at: +* http://license.coscl.org.cn/MulanPSL2 +* THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OF ANY KIND, +* EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT, +* MERCHANTABILITY OR FIT FOR A PARTICULAR PURPOSE. +* See the Mulan PSL v2 for more details. +*/ + +/** +* @file: task.h +* @brief: file task.h +* @version: 1.0 +* @author: AIIT XUOS Lab +* @date: 2023/05/18 +* +*/ + +#ifndef __TASK_H__ +#define __TASK_H__ + +#include +#include +#include +#include +#include + +// 任务状态枚举类型 +typedef enum { + TASK_CREATED, // 初始状态 + TASK_READY, // 就绪状态 + TASK_RUNNING, // 运行状态 + TASK_BLOCKED, // 阻塞状态 +} task_state_t; + + +// 任务控制块结构体 +typedef struct tcb { + uint32_t *stack_ptr; // 任务堆栈指针 + uint32_t *stack_bottom; // 任务堆栈底部指针 + uint32_t stack_size; // 任务堆栈大小 + task_state_t state; // 任务状态 + int priority; // 任务优先级 + struct tcb *next; // 指向下一个任务控制块的指针 + struct message_queue *message_queue; // 消息队列 +} tcb_t; + + +// 消息结构体 +typedef struct message { + int type; // 消息类型 + void *data; // 消息数据指针 +} message_t; + + +// 消息队列结构体 +typedef struct message_queue { + message_t *buffer; // 消息缓冲区 + int capacity; // 缓冲区容量 + int count; // 当前缓冲区中的消息数量 + int head; // 队头指针 + int tail; // 队尾指针 + semaphore_t *semaphore; // 信号量，用于实现消息队列的同步机制 +} message_queue_t; + + +// 信号量结构体 +typedef struct semaphore { + int count; // 计数器 + tcb_t *wait_list_head; // 指向等待信号量的任务控制块的指针 + mutex_t mutex; // 互斥锁，用于保护信号量和等待队列的访问 +} semaphore_t; + + +// 互斥锁结构体 +typedef struct mutex { + int lock; // 锁标志 +} mutex_t; + + +// 上下文结构体 +typedef struct { + uint32_t cpsr; // 控制寄存器 + uint32_t pc; // 程序计数器 + uint32_t r0; // 寄存器 R0 + uint32_t r1; // 寄存器 R1 + uint32_t r2; // 寄存器 R2 + uint32_t r3; // 寄存器 R3 + uint32_t r4; // 寄存器 R4 + uint32_t r5; // 寄存器 R5 + uint32_t r6; // 寄存器 R6 + uint32_t r7; // 寄存器 R7 + uint32_t r8; // 寄存器 R8 + uint32_t r9; // 寄存器 R9 + uint32_t r10; // 寄存器 R10 + uint32_t r11; // 寄存器 R11 + uint32_t r12; // 寄存器 R12 + uint32_t sp; // 栈指针 + uint32_t lr; // 链接寄存器 +} context_t; + +void tcb_init(tcb_t *tcb, int priority, int stack_size); +void tcb_destroy(tcb_t *tcb); +tcb_t *get_current_task(void); +tcb_t *get_local_run_queue_head(int cpu_id); +void add_to_global_run_queue(tcb_t *tcb); +tcb_t *take_from_global_run_queue(void); +void add_to_local_run_queue(tcb_t *tcb, int cpu_id); +tcb_t *take_from_local_run_queue(int cpu_id); +void move_current_task_to_global_run_queue(void); +void switch_to_next_task(void); +void task_init(tcb_t *tcb); +tcb_t *create_task(int priority, int stack_size); +void destroy_task(tcb_t *tcb); +void send_message(tcb_t *dest_tcb, int type, void *data); +void receive_message(int type, void *data); +message_queue_t *message_queue_create(int capacity); +void message_queue_destroy(message_queue_t *mq); +int message_queue_push(message_queue_t *mq, message_t *message); +int message_queue_pop(message_queue_t *mq, message_t *message); +int message_queue_push(message_queue_t *mq, message_t *message); +void context_init(context_t *context, void (*entry)(void), void *stack_ptr); +void wait_for_interrupt(void); +int get_cpu_id(void); +void *get_stack_pointer(void); +void set_stack_pointer(void *sp); +void add_interrupt_handler(int irq, void (*handler)(void), int priority); +void enter_critical(void); +void leave_critical(void); +void task_exit(void); +void task_entry(void); +#endif diff --git a/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/Kconfig b/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/Kconfig index 7f43c0a50..67bf8db13 100755 --- a/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/Kconfig +++ b/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/Kconfig @@ -11,7 +11,7 @@ menuconfig BSP_USING_SPI bool "Using SPI device" default n select RESOURCES_SPI - select BSP_USING_DMA + select BSP_USING_DMA if BSP_USING_SPI source "$BSP_DIR/third_party_driver/spi/Kconfig" endif @@ -117,6 +117,7 @@ menuconfig BSP_USING_WIZCHIP bool "Using w5500 as network device" default n select RESOURCES_WIZCHIP + select BSP_USING_SPI if BSP_USING_WIZCHIP source "$BSP_DIR/third_party_driver/ethernet/Kconfig" endif diff --git a/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/Kconfig b/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/Kconfig index baf59367c..b374d8fb0 100644 --- a/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/Kconfig +++ b/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/Kconfig @@ -1,15 +1,17 @@ # Kconfig file config BSP_USING_W5500 -bool "Using w5500 " -default y + bool "Using w5500" + default y -# if BSP_USING_W5500 - config BSP_WIZ_RST_PIN - int - default 13 +config BSP_WIZ_RST_PIN + int + default 13 - config BSP_WIZ_INT_PIN - int - default 14 -# endif \ No newline at end of file +config BSP_WIZ_INT_PIN + int + default 14 + +config BSP_WIZ_USE_IPERF + bool "Using iperf" + default y diff --git a/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/wiz_iperf.c b/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/wiz_iperf.c index 09c154347..3b1647c0f 100644 --- a/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/wiz_iperf.c +++ b/Ubiquitous/XiZi_IIoT/board/edu-riscv64/third_party_driver/ethernet/wiz_iperf.c @@ -2,6 +2,8 @@ #include "w5500.h" #include "connect_w5500.h" +#ifdef BSP_WIZ_USE_IPERF + #define IPERF_PORT 5001 #define IPERF_BUFSZ (4 * 1024) @@ -459,4 +461,5 @@ __usage: } SHELL_EXPORT_CMD(SHELL_CMD_PERMISSION(0) | SHELL_CMD_TYPE(SHELL_TYPE_CMD_MAIN), iperf, iperf, - iperf throughput test); \ No newline at end of file + iperf throughput test); +#endif diff --git a/Ubiquitous/XiZi_IIoT/board/xidatong-arm32/third_party_driver/common/pin_mux.c b/Ubiquitous/XiZi_IIoT/board/xidatong-arm32/third_party_driver/common/pin_mux.c index 0aa7d67f6..f39545239 100755 --- a/Ubiquitous/XiZi_IIoT/board/xidatong-arm32/third_party_driver/common/pin_mux.c +++ b/Ubiquitous/XiZi_IIoT/board/xidatong-arm32/third_party_driver/common/pin_mux.c @@ -47,6 +47,652 @@ void BOARD_InitBootPins(void) { BOARD_InitPins(); } +void SDHCPinmuxConfig(void) +{ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_14_USDHC1_VSELECT, /* GPIO_B1_14 is configured as USDHC1_VSELECT */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B0_00_USDHC1_CMD, /* GPIO_SD_B0_00 is configured as USDHC1_CMD */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B0_01_USDHC1_CLK, /* GPIO_SD_B0_01 is configured as USDHC1_CLK */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0, /* GPIO_SD_B0_02 is configured as USDHC1_DATA0 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1, /* GPIO_SD_B0_03 is configured as USDHC1_DATA1 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2, /* GPIO_SD_B0_04 is configured as USDHC1_DATA2 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3, /* GPIO_SD_B0_05 is configured as USDHC1_DATA3 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_14_USDHC1_VSELECT, /* GPIO_B1_14 PAD functional properties : */ + 0x0170A1u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/4 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B0_00_USDHC1_CMD, /* GPIO_SD_B0_00 PAD functional properties : */ + 0x017089u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0(150 Ohm @ 3.3V, 260 Ohm@1.8V) + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B0_01_USDHC1_CLK, /* GPIO_SD_B0_01 PAD functional properties : */ + 0x014089u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0(150 Ohm @ 3.3V, 260 Ohm@1.8V) + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Disabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0, /* GPIO_SD_B0_02 PAD functional properties : */ + 0x017089u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0(150 Ohm @ 3.3V, 260 Ohm@1.8V) + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1, /* GPIO_SD_B0_03 PAD functional properties : */ + 0x017089u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0(150 Ohm @ 3.3V, 260 Ohm@1.8V) + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2, /* GPIO_SD_B0_04 PAD functional properties : */ + 0x017089u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0(150 Ohm @ 3.3V, 260 Ohm@1.8V) + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3, /* GPIO_SD_B0_05 PAD functional properties : */ + 0x017089u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0(150 Ohm @ 3.3V, 260 Ohm@1.8V) + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 47K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ +} + +void SemcPinmuxConfig(void) +{ + + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_00_SEMC_DATA00, /* GPIO_EMC_00 is configured as SEMC_DATA00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_01_SEMC_DATA01, /* GPIO_EMC_01 is configured as SEMC_DATA01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_02_SEMC_DATA02, /* GPIO_EMC_02 is configured as SEMC_DATA02 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_03_SEMC_DATA03, /* GPIO_EMC_03 is configured as SEMC_DATA03 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_04_SEMC_DATA04, /* GPIO_EMC_04 is configured as SEMC_DATA04 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_05_SEMC_DATA05, /* GPIO_EMC_05 is configured as SEMC_DATA05 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_06_SEMC_DATA06, /* GPIO_EMC_06 is configured as SEMC_DATA06 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_07_SEMC_DATA07, /* GPIO_EMC_07 is configured as SEMC_DATA07 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_08_SEMC_DM00, /* GPIO_EMC_08 is configured as SEMC_DM00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_09_SEMC_ADDR00, /* GPIO_EMC_09 is configured as SEMC_ADDR00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_10_SEMC_ADDR01, /* GPIO_EMC_10 is configured as SEMC_ADDR01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_11_SEMC_ADDR02, /* GPIO_EMC_11 is configured as SEMC_ADDR02 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_12_SEMC_ADDR03, /* GPIO_EMC_12 is configured as SEMC_ADDR03 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_13_SEMC_ADDR04, /* GPIO_EMC_13 is configured as SEMC_ADDR04 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_14_SEMC_ADDR05, /* GPIO_EMC_14 is configured as SEMC_ADDR05 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_15_SEMC_ADDR06, /* GPIO_EMC_15 is configured as SEMC_ADDR06 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_16_SEMC_ADDR07, /* GPIO_EMC_16 is configured as SEMC_ADDR07 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_17_SEMC_ADDR08, /* GPIO_EMC_17 is configured as SEMC_ADDR08 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_18_SEMC_ADDR09, /* GPIO_EMC_18 is configured as SEMC_ADDR09 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_19_SEMC_ADDR11, /* GPIO_EMC_19 is configured as SEMC_ADDR11 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_20_SEMC_ADDR12, /* GPIO_EMC_20 is configured as SEMC_ADDR12 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_21_SEMC_BA0, /* GPIO_EMC_21 is configured as SEMC_BA0 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_22_SEMC_BA1, /* GPIO_EMC_22 is configured as SEMC_BA1 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_23_SEMC_ADDR10, /* GPIO_EMC_23 is configured as SEMC_ADDR10 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_24_SEMC_CAS, /* GPIO_EMC_24 is configured as SEMC_CAS */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_25_SEMC_RAS, /* GPIO_EMC_25 is configured as SEMC_RAS */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_26_SEMC_CLK, /* GPIO_EMC_26 is configured as SEMC_CLK */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_27_SEMC_CKE, /* GPIO_EMC_27 is configured as SEMC_CKE */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_28_SEMC_WE, /* GPIO_EMC_28 is configured as SEMC_WE */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_29_SEMC_CS0, /* GPIO_EMC_29 is configured as SEMC_CS0 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_30_SEMC_DATA08, /* GPIO_EMC_30 is configured as SEMC_DATA08 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_31_SEMC_DATA09, /* GPIO_EMC_31 is configured as SEMC_DATA09 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_32_SEMC_DATA10, /* GPIO_EMC_32 is configured as SEMC_DATA10 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_33_SEMC_DATA11, /* GPIO_EMC_33 is configured as SEMC_DATA11 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_34_SEMC_DATA12, /* GPIO_EMC_34 is configured as SEMC_DATA12 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_35_SEMC_DATA13, /* GPIO_EMC_35 is configured as SEMC_DATA13 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_36_SEMC_DATA14, /* GPIO_EMC_36 is configured as SEMC_DATA14 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_37_SEMC_DATA15, /* GPIO_EMC_37 is configured as SEMC_DATA15 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_38_SEMC_DM01, /* GPIO_EMC_38 is configured as SEMC_DM01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_39_SEMC_DQS, /* GPIO_EMC_39 is configured as SEMC_DQS */ + 1U); /* Software Input On Field: Force input path of pad GPIO_EMC_39 */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_40_SEMC_RDY, /* GPIO_EMC_40 is configured as SEMC_RDY */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_41_SEMC_CSX00, /* GPIO_EMC_41 is configured as SEMC_CSX00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_00_SEMC_DATA00, /* GPIO_EMC_00 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_01_SEMC_DATA01, /* GPIO_EMC_01 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_02_SEMC_DATA02, /* GPIO_EMC_02 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_03_SEMC_DATA03, /* GPIO_EMC_03 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_04_SEMC_DATA04, /* GPIO_EMC_04 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_05_SEMC_DATA05, /* GPIO_EMC_05 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_06_SEMC_DATA06, /* GPIO_EMC_06 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_07_SEMC_DATA07, /* GPIO_EMC_07 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_08_SEMC_DM00, /* GPIO_EMC_08 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_09_SEMC_ADDR00, /* GPIO_EMC_09 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_10_SEMC_ADDR01, /* GPIO_EMC_10 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_11_SEMC_ADDR02, /* GPIO_EMC_11 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_12_SEMC_ADDR03, /* GPIO_EMC_12 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_13_SEMC_ADDR04, /* GPIO_EMC_13 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_14_SEMC_ADDR05, /* GPIO_EMC_14 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_15_SEMC_ADDR06, /* GPIO_EMC_15 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_16_SEMC_ADDR07, /* GPIO_EMC_16 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_17_SEMC_ADDR08, /* GPIO_EMC_17 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_18_SEMC_ADDR09, /* GPIO_EMC_18 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_19_SEMC_ADDR11, /* GPIO_EMC_19 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_20_SEMC_ADDR12, /* GPIO_EMC_20 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_21_SEMC_BA0, /* GPIO_EMC_21 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_22_SEMC_BA1, /* GPIO_EMC_22 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_23_SEMC_ADDR10, /* GPIO_EMC_23 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_24_SEMC_CAS, /* GPIO_EMC_24 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_25_SEMC_RAS, /* GPIO_EMC_25 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_26_SEMC_CLK, /* GPIO_EMC_26 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_27_SEMC_CKE, /* GPIO_EMC_27 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_28_SEMC_WE, /* GPIO_EMC_28 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_29_SEMC_CS0, /* GPIO_EMC_29 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_30_SEMC_DATA08, /* GPIO_EMC_30 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_31_SEMC_DATA09, /* GPIO_EMC_31 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_32_SEMC_DATA10, /* GPIO_EMC_32 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_33_SEMC_DATA11, /* GPIO_EMC_33 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_34_SEMC_DATA12, /* GPIO_EMC_34 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_35_SEMC_DATA13, /* GPIO_EMC_35 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_36_SEMC_DATA14, /* GPIO_EMC_36 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_37_SEMC_DATA15, /* GPIO_EMC_37 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_38_SEMC_DM01, /* GPIO_EMC_38 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_39_SEMC_DQS, /* GPIO_EMC_39 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_40_SEMC_RDY, /* GPIO_EMC_40 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_41_SEMC_CSX00, /* GPIO_EMC_41 PAD functional properties : */ + 0x0110F9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/7 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Enabled */ +} /* * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* BOARD_InitPins: @@ -56,51 +702,313 @@ BOARD_InitPins: pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow} - {pin_num: K14, peripheral: LPUART1, signal: TX, pin_signal: GPIO_AD_B0_12, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm, pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow} - - {pin_num: F14, peripheral: GPIO1, signal: 'gpio_io, 09', pin_signal: GPIO_AD_B0_09, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm, - pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow} + - {pin_num: A7, peripheral: ENET, signal: enet_mdc, pin_signal: GPIO_EMC_40, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: C7, peripheral: ENET, signal: enet_mdio, pin_signal: GPIO_EMC_41, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Enable, speed: MHZ_50, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: B13, peripheral: ENET, signal: enet_ref_clk, pin_signal: GPIO_B1_10, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm, + pull_keeper_select: Keeper, pull_keeper_enable: Disable, open_drain: Disable, speed: MHZ_50, drive_strength: R0_6, slew_rate: Fast} + - {pin_num: E12, peripheral: ENET, signal: 'enet_rx_data, 0', pin_signal: GPIO_B1_04, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: D12, peripheral: ENET, signal: 'enet_rx_data, 1', pin_signal: GPIO_B1_05, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: C12, peripheral: ENET, signal: enet_rx_en, pin_signal: GPIO_B1_06, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: C13, peripheral: ENET, signal: enet_rx_er, pin_signal: GPIO_B1_11, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: B12, peripheral: ENET, signal: 'enet_tx_data, 0', pin_signal: GPIO_B1_07, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: A12, peripheral: ENET, signal: 'enet_tx_data, 1', pin_signal: GPIO_B1_08, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: A13, peripheral: ENET, signal: enet_tx_en, pin_signal: GPIO_B1_09, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_200, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: F14, peripheral: GPIO1, signal: 'gpio_io, 09', pin_signal: GPIO_AD_B0_09, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: G13, peripheral: GPIO1, signal: 'gpio_io, 10', pin_signal: GPIO_AD_B0_10, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_100K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_5, slew_rate: Fast} + - {pin_num: J3, peripheral: USDHC1, signal: usdhc_clk, pin_signal: GPIO_SD_B0_01, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Keeper, pull_keeper_enable: Disable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast} + - {pin_num: J4, peripheral: USDHC1, signal: usdhc_cmd, pin_signal: GPIO_SD_B0_00, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast} + - {pin_num: J1, peripheral: USDHC1, signal: 'usdhc_data, 0', pin_signal: GPIO_SD_B0_02, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast} + - {pin_num: K1, peripheral: USDHC1, signal: 'usdhc_data, 1', pin_signal: GPIO_SD_B0_03, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast} + - {pin_num: H2, peripheral: USDHC1, signal: 'usdhc_data, 2', pin_signal: GPIO_SD_B0_04, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast} + - {pin_num: J2, peripheral: USDHC1, signal: 'usdhc_data, 3', pin_signal: GPIO_SD_B0_05, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast} + - {pin_num: C14, peripheral: USDHC1, signal: usdhc_vselect, pin_signal: GPIO_B1_14, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm, + pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_4, slew_rate: Fast} * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** */ - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitPins - * Description : Configures pin routing and optionally pin electrical features. - * - * END ****************************************************************************************************************/ -void BOARD_InitPins(void) { - CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */ - - IOMUXC_SetPinMux( - IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 is configured as GPIO1_IO09 */ +void Lcd_InitPins(void) +{ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_00_LCD_CLK, /* GPIO_B0_00 is configured as LCD_CLK */ 0U); /* Software Input On Field: Input Path is determined by functionality */ IOMUXC_SetPinMux( - IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 is configured as LPUART1_TX */ + IOMUXC_GPIO_B0_01_LCD_ENABLE, /* GPIO_B0_01 is configured as LCD_ENABLE */ 0U); /* Software Input On Field: Input Path is determined by functionality */ IOMUXC_SetPinMux( - IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 is configured as LPUART1_RX */ + IOMUXC_GPIO_B0_02_LCD_HSYNC, /* GPIO_B0_02 is configured as LCD_HSYNC */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_03_LCD_VSYNC, /* GPIO_B0_03 is configured as LCD_VSYNC */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_04_LCD_DATA00, /* GPIO_B0_04 is configured as LCD_DATA00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_05_LCD_DATA01, /* GPIO_B0_05 is configured as LCD_DATA01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_06_LCD_DATA02, /* GPIO_B0_06 is configured as LCD_DATA02 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_07_LCD_DATA03, /* GPIO_B0_07 is configured as LCD_DATA03 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_08_LCD_DATA04, /* GPIO_B0_08 is configured as LCD_DATA04 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_09_LCD_DATA05, /* GPIO_B0_09 is configured as LCD_DATA05 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_10_LCD_DATA06, /* GPIO_B0_10 is configured as LCD_DATA06 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_11_LCD_DATA07, /* GPIO_B0_11 is configured as LCD_DATA07 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_12_LCD_DATA08, /* GPIO_B0_12 is configured as LCD_DATA08 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_13_LCD_DATA09, /* GPIO_B0_13 is configured as LCD_DATA09 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_14_LCD_DATA10, /* GPIO_B0_14 is configured as LCD_DATA10 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B0_15_LCD_DATA11, /* GPIO_B0_15 is configured as LCD_DATA11 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_00_LCD_DATA12, /* GPIO_B1_00 is configured as LCD_DATA12 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_01_LCD_DATA13, /* GPIO_B1_01 is configured as LCD_DATA13 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_02_LCD_DATA14, /* GPIO_B1_02 is configured as LCD_DATA14 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_03_LCD_DATA15, /* GPIO_B1_03 is configured as LCD_DATA15 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_15_GPIO2_IO31, /* GPIO_B1_15 is configured as GPIO2_IO31 */ 0U); /* Software Input On Field: Input Path is determined by functionality */ IOMUXC_SetPinConfig( - IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 PAD functional properties : */ - 0x10B0u); /* Slew Rate Field: Slow Slew Rate + IOMUXC_GPIO_B0_00_LCD_CLK, /* GPIO_B0_00 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate Drive Strength Field: R0/6 Speed Field: medium(100MHz) Open Drain Enable Field: Open Drain Disabled Pull / Keep Enable Field: Pull/Keeper Enabled - Pull / Keep Select Field: Keeper - Pull Up / Down Config. Field: 100K Ohm Pull Down - Hyst. Enable Field: Hysteresis Disabled */ + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ IOMUXC_SetPinConfig( - IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 PAD functional properties : */ - 0x10B0u); /* Slew Rate Field: Slow Slew Rate + IOMUXC_GPIO_B0_01_LCD_ENABLE, /* GPIO_B0_01 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate Drive Strength Field: R0/6 Speed Field: medium(100MHz) Open Drain Enable Field: Open Drain Disabled Pull / Keep Enable Field: Pull/Keeper Enabled - Pull / Keep Select Field: Keeper - Pull Up / Down Config. Field: 100K Ohm Pull Down - Hyst. Enable Field: Hysteresis Disabled */ + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ IOMUXC_SetPinConfig( - IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 PAD functional properties : */ + IOMUXC_GPIO_B0_02_LCD_HSYNC, /* GPIO_B0_02 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_03_LCD_VSYNC, /* GPIO_B0_03 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_04_LCD_DATA00, /* GPIO_B0_04 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_05_LCD_DATA01, /* GPIO_B0_05 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_06_LCD_DATA02, /* GPIO_B0_06 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_07_LCD_DATA03, /* GPIO_B0_07 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_08_LCD_DATA04, /* GPIO_B0_08 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_09_LCD_DATA05, /* GPIO_B0_09 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_10_LCD_DATA06, /* GPIO_B0_10 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_11_LCD_DATA07, /* GPIO_B0_11 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_12_LCD_DATA08, /* GPIO_B0_12 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_13_LCD_DATA09, /* GPIO_B0_13 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_14_LCD_DATA10, /* GPIO_B0_14 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B0_15_LCD_DATA11, /* GPIO_B0_15 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_00_LCD_DATA12, /* GPIO_B1_00 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_01_LCD_DATA13, /* GPIO_B1_01 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_02_LCD_DATA14, /* GPIO_B1_02 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_03_LCD_DATA15, /* GPIO_B1_03 PAD functional properties : */ + 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Enabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_15_GPIO2_IO31, /* GPIO_B1_15 PAD functional properties : */ 0x10B0u); /* Slew Rate Field: Slow Slew Rate Drive Strength Field: R0/6 Speed Field: medium(100MHz) @@ -111,6 +1019,334 @@ void BOARD_InitPins(void) { Hyst. Enable Field: Hysteresis Disabled */ } +void BOARD_InitI2C1Pins(void) { + CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */ + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL, /* GPIO_AD_B1_00 is configured as LPI2C1_SCL */ + 1U); /* Software Input On Field: Force input path of pad GPIO_AD_B1_00 */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA, /* GPIO_AD_B1_01 is configured as LPI2C1_SDA */ + 1U); /* Software Input On Field: Force input path of pad GPIO_AD_B1_01 */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL, /* GPIO_AD_B1_00 PAD functional properties : */ + 0xD8B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Enabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 22K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA, /* GPIO_AD_B1_01 PAD functional properties : */ + 0xD8B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Enabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 22K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ +} + +void BOARD_InitUartPins(void) +{ +#ifdef BSP_USING_LPUART1 + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 is configured as LPUART1_TX */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 is configured as LPUART1_RX */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 PAD functional properties : */ + 0x10B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 PAD functional properties : */ + 0x10B0u); /* Slew Rate Field: Slow Slew Rate + Drive Strength Field: R0/6 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Disabled */ +#endif +#ifdef BSP_USING_LPUART2 + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_02_LPUART2_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_03_LPUART2_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_02_LPUART2_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_03_LPUART2_RX, + 0x10B0u); +#endif + +#ifdef BSP_USING_LPUART3 + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_06_LPUART3_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_07_LPUART3_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_06_LPUART3_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_07_LPUART3_RX, + 0x10B0u); +#endif + + +#ifdef BSP_USING_LPUART4 + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B1_00_LPUART4_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_SD_B1_01_LPUART4_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B1_00_LPUART4_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_SD_B1_01_LPUART4_RX, + 0x10B0u); +#endif + +#ifdef BSP_USING_LPUART8 + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_10_LPUART8_TX, + 0U); + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B1_11_LPUART8_RX, + 0U); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_10_LPUART8_TX, + 0x10B0u); + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B1_11_LPUART8_RX, + 0x10B0u); +#endif +} + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitPins + * Description : Configures pin routing and optionally pin electrical features. + * + * END ****************************************************************************************************************/ +void BOARD_InitPins(void) +{ + CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */ + /* Software Input On Field: Input Path is determined by functionality */ + SemcPinmuxConfig(); + +#ifdef BSP_USING_LPUART + BOARD_InitUartPins(); +#endif + +#ifdef BSP_USING_LCD + Lcd_InitPins(); +#endif + +#ifdef BSP_USING_I2C + BOARD_InitI2C1Pins(); +#endif + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_03_GPIO1_IO03, /* GPIO_AD_B0_09 is configured as GPIO1_IO09 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, /* GPIO_AD_B0_10 is configured as GPIO1_IO10 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 is configured as LPUART1_TX */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 is configured as LPUART1_RX */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + + + IOMUXC_SetPinMux( + IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 is configured as GPIO1_IO09 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 PAD functional properties : */ + 0x10B0u); /* Slew Rate Field: Slow Slew Rate */ + +#ifdef BSP_USING_SDIO + SDHCPinmuxConfig(); +#endif + + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_04_ENET_RX_DATA00, /* GPIO_B1_04 is configured as ENET_RX_DATA00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_05_ENET_RX_DATA01, /* GPIO_B1_05 is configured as ENET_RX_DATA01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_06_ENET_RX_EN, /* GPIO_B1_06 is configured as ENET_RX_EN */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_07_ENET_TX_DATA00, /* GPIO_B1_07 is configured as ENET_TX_DATA00 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_08_ENET_TX_DATA01, /* GPIO_B1_08 is configured as ENET_TX_DATA01 */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_09_ENET_TX_EN, /* GPIO_B1_09 is configured as ENET_TX_EN */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_10_ENET_REF_CLK, /* GPIO_B1_10 is configured as ENET_REF_CLK */ + 1U); /* Software Input On Field: Force input path of pad GPIO_B1_10 */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_B1_11_ENET_RX_ER, /* GPIO_B1_11 is configured as ENET_RX_ER */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_40_ENET_MDC, /* GPIO_EMC_40 is configured as ENET_MDC */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + IOMUXC_SetPinMux( + IOMUXC_GPIO_EMC_41_ENET_MDIO, /* GPIO_EMC_41 is configured as ENET_MDIO */ + 0U); /* Software Input On Field: Input Path is determined by functionality */ + + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_03_GPIO1_IO03, /* GPIO_AD_B0_09 PAD functional properties : */ + 0xB0A9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + + IOMUXC_SetPinConfig( + IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, /* GPIO_AD_B0_10 PAD functional properties : */ + 0xB0A9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: medium(100MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_04_ENET_RX_DATA00, /* GPIO_B1_04 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_05_ENET_RX_DATA01, /* GPIO_B1_05 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_06_ENET_RX_EN, /* GPIO_B1_06 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_07_ENET_TX_DATA00, /* GPIO_B1_07 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_08_ENET_TX_DATA01, /* GPIO_B1_08 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_09_ENET_TX_EN, /* GPIO_B1_09 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_10_ENET_REF_CLK, /* GPIO_B1_10 PAD functional properties : */ + 0x31u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/6 + Speed Field: low(50MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Disabled + Pull / Keep Select Field: Keeper + Pull Up / Down Config. Field: 100K Ohm Pull Down + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_B1_11_ENET_RX_ER, /* GPIO_B1_11 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_40_ENET_MDC, /* GPIO_EMC_40 PAD functional properties : */ + 0xB0E9u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: max(200MHz) + Open Drain Enable Field: Open Drain Disabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ + IOMUXC_SetPinConfig( + IOMUXC_GPIO_EMC_41_ENET_MDIO, /* GPIO_EMC_41 PAD functional properties : */ + 0xB829u); /* Slew Rate Field: Fast Slew Rate + Drive Strength Field: R0/5 + Speed Field: low(50MHz) + Open Drain Enable Field: Open Drain Enabled + Pull / Keep Enable Field: Pull/Keeper Enabled + Pull / Keep Select Field: Pull + Pull Up / Down Config. Field: 100K Ohm Pull Up + Hyst. Enable Field: Hysteresis Disabled */ +} + /*********************************************************************************************************************** * EOF **********************************************************************************************************************/ diff --git a/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/lwipopts.h b/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/lwipopts.h index 577169deb..5bbd27f95 100644 --- a/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/lwipopts.h +++ b/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/lwipopts.h @@ -536,7 +536,7 @@ The STM32F4x7 allows computing and verifying the IP, UDP, TCP and ICMP checksums #define DEFAULT_THREAD_STACKSIZE 1024 #define TCPIP_THREAD_NAME "tcp" -#define TCPIP_THREAD_STACKSIZE 4096 +#define TCPIP_THREAD_STACKSIZE 1024 #define TCPIP_MBOX_SIZE 16 #define TCPIP_THREAD_PRIO 20 diff --git a/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/sys_arch.h b/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/sys_arch.h index 384b85b1a..e606c710b 100644 --- a/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/sys_arch.h +++ b/Ubiquitous/XiZi_IIoT/resources/ethernet/LwIP/arch/sys_arch.h @@ -54,7 +54,7 @@ #define LWIP_TARGET_PORT LWIP_LOCAL_PORT #define LWIP_DEMO_TIMES 10 -#define LWIP_TASK_STACK_SIZE 4096 +#define LWIP_TASK_STACK_SIZE 1536 #define LWIP_DEMO_TASK_PRIO 20 // /* MAC address configuration. */ diff --git a/Ubiquitous/XiZi_IIoT/resources/ethernet/cmd_lwip/lwip_tcp_demo.c b/Ubiquitous/XiZi_IIoT/resources/ethernet/cmd_lwip/lwip_tcp_demo.c index 6f1c8d2b9..e1ad56550 100755 --- a/Ubiquitous/XiZi_IIoT/resources/ethernet/cmd_lwip/lwip_tcp_demo.c +++ b/Ubiquitous/XiZi_IIoT/resources/ethernet/cmd_lwip/lwip_tcp_demo.c @@ -28,7 +28,7 @@ #include "tcpecho_raw.h" char tcp_demo_msg[LWIP_TEST_MSG_SIZE] = { 0 }; char tcp_demo_ip[] = {192, 168, 250, 252}; -u16_t tcp_demo_port = LWIP_TARGET_PORT; +u16_t tcp_demo_port = 80; int tcp_send_num = 0; int tcp_send_task_on = 0; uint32 tcp_interval = 50;