menuconfig RESOURCES_SERIAL
    bool "Using SERIAL bus drivers"
    select KERNEL_WORKQUEUE
    default y

if RESOURCES_SERIAL
    config SERIAL_USING_DMA
        bool "Enable SERIAL DMA mode"
        default y

    config SERIAL_RB_BUFSZ
        int "Set SERIAL RX buffer size"
        default 128
endif

if BSP_USING_CAN
    config RESOURCES_CAN
        bool "Using CAN bus drivers"
        default y
endif

if BSP_USING_I2C
    config RESOURCES_I2C
        bool "Using I2C bus drivers"
        default n
endif

if BSP_USING_LCD
    config RESOURCES_LCD
        bool "Using LCD bus drivers"
        default n
endif

if BSP_USING_GPIO
    config RESOURCES_PIN
        bool "Using generic GPIO PIN bus drivers"
        default n
endif

if BSP_USING_RTC
    menuconfig RESOURCES_RTC
        bool "Using RTC bus drivers"
        default n

        if RESOURCES_RTC
            config USING_SOFT_RTC
            bool "Using SOFT RTC"
            default n
            if USING_SOFT_RTC
                config SOFT_RTC_BUS_NAME
                    string "soft rtc bus name"
                    default "srtc"
                config SOFT_RTC_DRV_NAME
                    string "soft rtc bus driver name"
                    default "srtc_drv"  
            endif
        endif
endif

if BSP_USING_SDIO
    config RESOURCES_SDIO
        bool "Using SD/MMC card bus drivers"
        default n
endif

if BSP_USING_SPI
    menuconfig RESOURCES_SPI
        bool "Using SPI bus drivers"
        default n

        if RESOURCES_SPI  
            menuconfig RESOURCES_SPI_SD
                bool "Using SD/TF card driver with spi"
                    default n
                if RESOURCES_SPI_SD
                    config SPI_SD_NAME
                    string "spi sd card 0 name"
                    default "sd0"
                endif

            menuconfig RESOURCES_SPI_SFUD
                bool "Using Serial Flash Universal Driver Lib"
                default n
                if RESOURCES_SPI_SFUD
                    config SFUD_USING_SFDP
                    bool "Using auto probe flash JEDEC SFDP parameter"
                    default y

                    config SFUD_USING_FLASH_INFO_TABLE
                    bool "Using defined supported flash chip information table"
                    default n
                    
                    config SFUD_DEBUG_LOG
                    bool "Support SFUD debug log"
                    default y
                endif
        endif
endif

if BSP_USING_HWTIMER
    config RESOURCES_HWTIMER
        bool "Using hardware timer bus drivers"
        default n
endif

if BSP_USING_TOUCH
    config RESOURCES_TOUCH
        bool "Using touch bus drivers"
        default n
endif

if BSP_USING_USB
    menuconfig RESOURCES_USB
        bool "Using USB bus drivers"
        default n
        
    if RESOURCES_USB
        config RESOURCES_USB_HOST
            bool "Using USB host function"
            default y
            if RESOURCES_USB_HOST
                    config UDISK_MOUNTPOINT
                        string "Udisk mount dir"
                        default "/"
            endif
                    config USBH_MSTORAGE
                        bool "usb use mass storage device"
                        default y
                        select FS_VFS

        config RESOURCES_USB_DEVICE
            bool "Using USB device function"
            default y
            
            if RESOURCES_USB_DEVICE
                config USBD_THREAD_STACK_SZ
                    int "usb thread stack size"
                    default 4096
            endif
    endif
endif

if BSP_USING_WDT
    config RESOURCES_WDT
        bool "Using Watch Dog bus drivers"
        default n
endif