Merge branch 'prepare_for_master' of https://git.trustie.net/xuos/xiuos into develop

Ubiquitous/XiZi/board/aiit-riscv64-board/board.c

@@ -222,6 +222,9 @@ void InitBoardHardware(void)
     DmacInit();
 #endif
 
+    /* initialize memory system */
+	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
     /* initalize interrupt */
     InitHwinterrupt();
 #ifdef BSP_USING_UART    
@@ -239,8 +242,7 @@ void InitBoardHardware(void)
 #ifdef ARCH_SMP
     EnableHwclintIpi();
 #endif
-    /* initialize memory system */
-	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
 
 #ifdef KERNEL_COMPONENTS_INIT
 	for(i = 0; _board_init[i].fn != NONE; i++) {

Ubiquitous/XiZi/board/cortex-m0-emulator/board.c

@@ -34,6 +34,8 @@ void InitBoardHardware()
 {
 	extern int InitHwUart(void);
 	InitHwUart();
-	InstallConsole(SERIAL_BUS_NAME_1, SERIAL_DRV_NAME_1, SERIAL_DEVICE_NAME_1);
+
 	InitBoardMemory((void*)LM3S_SRAM_START, (void*)LM3S_SRAM_END);
+
+	InstallConsole(SERIAL_BUS_NAME_1, SERIAL_DRV_NAME_1, SERIAL_DEVICE_NAME_1);
 }

Ubiquitous/XiZi/board/cortex-m3-emulator/board.c

@@ -34,7 +34,7 @@ void InitBoardHardware()
 {
 	extern int InitHwUart(void);
 	InitHwUart();
-	InstallConsole(SERIAL_BUS_NAME_1, SERIAL_DRV_NAME_1, SERIAL_DEVICE_NAME_1);
-	InitBoardMemory((void*)LM3S_SRAM_START, (void*)LM3S_SRAM_END);
 
+	InitBoardMemory((void*)LM3S_SRAM_START, (void*)LM3S_SRAM_END);
+	InstallConsole(SERIAL_BUS_NAME_1, SERIAL_DRV_NAME_1, SERIAL_DEVICE_NAME_1);
 }

Ubiquitous/XiZi/board/cortex-m4-emulator/board.c

@@ -109,6 +109,9 @@ void InitBoardHardware()
 #ifdef BSP_USING_UART
 	Stm32HwUsartInit();
 #endif
+
+    InitBoardMemory((void*)MEMORY_START_ADDRESS, (void*)MEMORY_END_ADDRESS);
+
 #ifdef KERNEL_CONSOLE
     InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
 
@@ -119,7 +122,5 @@ void InitBoardHardware()
     KPrintf("\nconsole init completed.\n");
     KPrintf("board initialization......\n");
 #endif
-    
-    InitBoardMemory((void*)MEMORY_START_ADDRESS, (void*)MEMORY_END_ADDRESS);
 	
 }

Ubiquitous/XiZi/board/hifive1-emulator/board.c

@@ -54,6 +54,9 @@ void InitBoardHardware(void)
     CLINT_MTIMECMP_ADDR = CLINT_MTIME_ADDR + TICK;
     SET_CSR(mie, MIP_MTIP);
 
+    /* initialize memory system */
+	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
     extern int InitHwUart(void);
     InitHwUart();
     InstallConsole(SERIAL_BUS_NAME, SERIAL_DRV_NAME, SERIAL_DEVICE_NAME);
@@ -62,8 +65,6 @@ void InitBoardHardware(void)
     KPrintf("board initialization......\n");
 
     KPrintf("memory address range: [0x%08x - 0x%08x], size: %d\n", (x_ubase) MEMORY_START_ADDRESS, (x_ubase) MEMORY_END_ADDRESS, MEMORY_SIZE);
-    /* initialize memory system */
-	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
 
     return;
 }

Ubiquitous/XiZi/board/hifive1-rev-B/board.c

@@ -54,6 +54,9 @@ void InitBoardHardware(void)
     CLINT_MTIMECMP_ADDR = CLINT_MTIME_ADDR + TICK;
     SET_CSR(mie, MIP_MTIP);
 
+    /* initialize memory system */
+	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
     extern int InitHwUart(void);
     InitHwUart();
     InstallConsole(SERIAL_BUS_NAME, SERIAL_DRV_NAME, SERIAL_DEVICE_NAME);
@@ -62,8 +65,6 @@ void InitBoardHardware(void)
     KPrintf("board initialization......\n");
 
     KPrintf("memory address range: [0x%08x - 0x%08x], size: %d\n", (x_ubase) MEMORY_START_ADDRESS, (x_ubase) MEMORY_END_ADDRESS, MEMORY_SIZE);
-    /* initialize memory system */
-	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
 
     return;
 }

Ubiquitous/XiZi/board/k210-emulator/board.c

@@ -153,6 +153,10 @@ void InitBoardHardware(void)
 #ifdef BSP_USING_UART    
     HwUartInit();
 #endif
+
+    /* initialize memory system */
+	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
 #ifdef KERNEL_CONSOLE
     /* set console device */
     InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
@@ -165,8 +169,6 @@ void InitBoardHardware(void)
 #ifdef ARCH_SMP
     EnableHwclintIpi();
 #endif
-    /* initialize memory system */
-	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
 
 #ifdef KERNEL_COMPONENTS_INIT
 	for(i = 0; _board_init[i].fn != NONE; i++) {

Ubiquitous/XiZi/board/kd233/board.c

@@ -202,6 +202,10 @@ void InitBoardHardware(void)
 #ifdef BSP_USING_UART    
     HwUartInit();
 #endif
+
+    /* initialize memory system */
+	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
 #ifdef KERNEL_CONSOLE
     /* set console device */
     InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
@@ -214,8 +218,6 @@ void InitBoardHardware(void)
 #ifdef ARCH_SMP
     EnableHwclintIpi();
 #endif
-    /* initialize memory system */
-	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
 
 #ifdef KERNEL_COMPONENTS_INIT
 	for(i = 0; _board_init[i].fn != NONE; i++) {

Ubiquitous/XiZi/board/maix-go/board.c

@@ -146,6 +146,10 @@ void InitBoardHardware(void)
 #ifdef BSP_USING_UART    
     HwUartInit();
 #endif
+
+    /* initialize memory system */
+	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
 #ifdef KERNEL_CONSOLE
     /* set console device */
     InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
@@ -158,9 +162,6 @@ void InitBoardHardware(void)
 #ifdef ARCH_SMP
     EnableHwclintIpi();
 #endif
-    /* initialize memory system */
-	InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
-
 
 	KPrintf("board init done.\n");
 	KPrintf("start kernel...\n");

Ubiquitous/XiZi/board/ok1052-c/Kconfig

@@ -44,7 +44,6 @@ menu "ok1052-c feature"
         config MOUNT_SDCARD
             bool "mount cd card"
             default n
-            select BSP_USING_SDIO
     endmenu
 
 endmenu

Ubiquitous/XiZi/board/ok1052-c/board.c

@@ -41,30 +41,6 @@ extern int ExtSramInit(void);
 #endif
 #endif
 
-#if defined(FS_VFS) && defined(MOUNT_SDCARD)
-#include <iot-vfs.h>
-
-// SD card mount flag 1: OK
-int sd_mount_flag = 0;
-
-/**
- * @description: Mount SD card
- * @return 0
- */
-int MountSDCard(void)
-{
-    if (MountFilesystem(SDIO_BUS_NAME, SDIO_DEVICE_NAME, SDIO_DRIVER_NAME, FSTYPE_FATFS, "/") == 0)
-    {
-        sd_mount_flag = 1;
-        KPrintf("sd card mount to '/'");
-    }
-    else
-        KPrintf("sd card mount to '/' failed!");
-
-    return 0;
-}
-#endif
-
 #if defined(SDK_I2C_BASED_COMPONENT_USED) && SDK_I2C_BASED_COMPONENT_USED
 #include "fsl_lpi2c.h"
 #endif /* SDK_I2C_BASED_COMPONENT_USED */

Ubiquitous/XiZi/board/ok1052-c/third_party_driver/ethernet/enet_ethernetif.c

@@ -99,7 +99,7 @@ void ethernetif_clk_init(void)
 {
     const clock_enet_pll_config_t config = {.enableClkOutput = true, .enableClkOutput25M = false, .loopDivider = 1};
     CLOCK_InitEnetPll(&config);
-    SysTick_Config(USEC_TO_COUNT(1000U, CLOCK_GetFreq(kCLOCK_CoreSysClk)));
+    SysTick_Config(SystemCoreClock / TICK_PER_SECOND);
 }
 
 void ethernetif_gpio_init(void)
@@ -109,9 +109,7 @@ void ethernetif_gpio_init(void)
     IOMUXC_EnableMode(IOMUXC_GPR, kIOMUXC_GPR_ENET1TxClkOutputDir, true);
 
     GPIO_PinInit(GPIO1, 3, &gpio_config);
-    GPIO_PinInit(GPIO1, 10, &gpio_config);
     /* pull up the ENET_INT before RESET. */
-    GPIO_WritePinOutput(GPIO1, 10, 1);
     GPIO_WritePinOutput(GPIO1, 3, 0);
     enet_delay();
     GPIO_WritePinOutput(GPIO1, 3, 1);

Ubiquitous/XiZi/board/ok1052-c/third_party_driver/include/connect_sdio.h

@@ -27,11 +27,14 @@
 #include <clock_config.h>
 #include <fsl_gpio.h>
 #include <fsl_common.h>
+#include <connect_gpio.h>
 
 #ifdef __cplusplus
 extern "C" {
 #endif
 
+#define SD_CARD_STACK_SIZE 2048
+
 int Imxrt1052HwSdioInit(void);
 
 #ifdef __cplusplus

Ubiquitous/XiZi/board/ok1052-c/third_party_driver/sdio/Kconfig

@@ -10,4 +10,15 @@ if BSP_USING_SDIO
     config SDIO_DEVICE_NAME
         string "sdio device name"
         default "sdio_dev"
+
+    config MOUNT_SDCARD_FS
+        bool "mount cd card file system"
+        default n
+        select MOUNT_SDCARD
+
+    if MOUNT_SDCARD_FS
+        config MOUNT_SDCARD_FS_TYPE
+            int "choose file system type : FATFS(0) LWEXT4(3)"
+            default 0 
+    endif
 endif

Ubiquitous/XiZi/board/ok1052-c/third_party_driver/sdio/connect_sdio.c

@@ -104,9 +104,6 @@ static const sdmmchost_card_switch_voltage_func_t s_sdcard_voltage_switch = {
 };
 #endif
 
-/*! @brief SD card detect flag  */
-static volatile bool s_card_inserted = false;
-
 /*! @brief Card descriptor. */
 static sd_card_t g_sd;
 static int sd_lock = -1;
@@ -142,11 +139,6 @@ static void BoardPowerOnSdCard(void)
     BOARD_USDHC_SDCARD_POWER_CONTROL(1);
 }
 
-static void SdcardDetectCallBack(bool is_inserted, void *user_data)
-{
-    s_card_inserted = is_inserted;
-}
-
 static void CardInformationLog(sd_card_t *card)
 {
     NULL_PARAM_CHECK(card);
@@ -261,6 +253,19 @@ static uint32 SdioWrite(void *dev, struct BusBlockWriteParam *write_param)
     return write_param->size;
 }
 
+static int SdioControl(struct HardwareDev *dev, struct HalDevBlockParam *block_param)
+{
+    NULL_PARAM_CHECK(dev);
+
+    if (OPER_BLK_GETGEOME == block_param->cmd) {
+        block_param->dev_block.size_perbank = g_sd.blockSize;
+        block_param->dev_block.block_size = g_sd.blockSize;
+        block_param->dev_block.bank_num = g_sd.blockCount;
+    }
+
+    return EOK;
+}
+
 static struct SdioDevDone dev_done =
 {
     SdioOpen,
@@ -269,10 +274,126 @@ static struct SdioDevDone dev_done =
     SdioRead,
 };
 
+#if defined(FS_VFS) && defined(MOUNT_SDCARD_FS)
+#include <iot-vfs.h>
+
+int sd_mount_flag = 0;
+
+/**
+ * @description: Mount SD card
+ * @return 0
+ */
+static int MountSDCardFs(enum FilesystemType fs_type)
+{
+    if (MountFilesystem(SDIO_BUS_NAME, SDIO_DEVICE_NAME, SDIO_DRIVER_NAME, fs_type, "/") == 0) {
+        sd_mount_flag = 1;
+        KPrintf("Sd card mount to '/'");
+    } else {
+        KPrintf("Sd card mount to '/' failed!");
+    }
+    
+    return 0;
+}
+#endif
+
+static void SdCardAttach(void)
+{
+    bool is_read_only;
+    static sd_card_t *card = &g_sd;
+    
+    KPrintf("\r\nCard inserted.\r\n");
+    /* reset host once card re-plug in */
+    SD_HostReset(&(card->host));
+    /* power on the card */
+    SD_PowerOnCard(card->host.base, card->usrParam.pwr);
+    KPrintf("Power on done\n");
+
+    /* Init card. */
+    if (SD_CardInit(card)) {
+        KPrintf("\r\nSD card init failed.\r\n");
+        return;
+    }
+
+    /* card information log */
+    CardInformationLog(card);
+
+    /* Check if card is readonly. */
+    is_read_only = SD_CheckReadOnly(card);
+
+#ifdef MOUNT_SDCARD_FS
+    /*mount file system*/
+    MountSDCardFs(MOUNT_SDCARD_FS_TYPE);
+#endif
+}
+
+static void SdCardDetach(void)
+{
+    /*unmount file system*/
+    KPrintf("\r\nCard detect extracted.\r\n");
+
+#ifdef MOUNT_SDCARD_FS
+    UnmountFileSystem("/");
+#endif
+}
+
+static uint8 SdCardReadCd(void)
+{
+	BusType pin;
+
+    pin = BusFind(PIN_BUS_NAME);
+
+    pin->owner_haldev = BusFindDevice(pin, PIN_DEVICE_NAME);
+
+    struct PinStat PinStat;
+
+    struct BusBlockReadParam read_param;
+    read_param.buffer = (void *)&PinStat;
+
+    PinStat.pin = IMXRT_GET_PIN(2, 28);
+    
+    return BusDevReadData(pin->owner_haldev, &read_param);
+}
+
+static void SdCardTask(void* parameter)
+{
+    static int sd_card_status = 0;
+
+    while (1) {
+        if (!SdCardReadCd()) {
+            if (!sd_card_status) {
+                SdCardAttach();
+                sd_card_status = 1;
+            }
+        } else {
+            if (sd_card_status) {
+                SdCardDetach();
+                sd_card_status = 0;
+            }
+        }
+    }
+}
+
+#ifdef MOUNT_SDCARD
+int MountSDCard()
+{
+    int sd_card_task = 0;
+    sd_card_task = KTaskCreate("sd_card", SdCardTask, NONE,
+                           SD_CARD_STACK_SIZE, 8);
+    if(sd_card_task < 0) {		
+		KPrintf("sd_card_task create failed ...%s %d.\n", __FUNCTION__,__LINE__);
+		return ERROR;
+	}
+
+    StartupKTask(sd_card_task);
+
+    return EOK;
+}
+#endif
+
+
 int Imxrt1052HwSdioInit(void)
 {
     x_err_t ret = EOK;
-    bool is_read_only;
 
     static struct SdioBus sdio_bus;
     static struct SdioDriver sdio_drv;
@@ -305,35 +426,6 @@ int Imxrt1052HwSdioInit(void)
         return ERROR;
     }
 
-    KPrintf("\r\nPlease insert a card into board.\r\n");
-
-    /* power off card */
-    SD_PowerOffCard(card->host.base, card->usrParam.pwr);
-
-    if (SD_WaitCardDetectStatus(SD_HOST_BASEADDR, &s_sdcard_detect, true) == kStatus_Success) {
-        KPrintf("\r\nCard inserted.\r\n");
-        /* reset host once card re-plug in */
-        SD_HostReset(&(card->host));
-        /* power on the card */
-        SD_PowerOnCard(card->host.base, card->usrParam.pwr);
-        KPrintf("power on done\n");
-    } else {
-        KPrintf("\r\nCard detect fail.\r\n");
-        return ERROR;
-    }
-
-    /* Init card. */
-    if (SD_CardInit(card)) {
-        KPrintf("\r\nSD card init failed.\r\n");
-        return ERROR;
-    }
-
-    /* card information log */
-    CardInformationLog(card);
-
-    /* Check if card is readonly. */
-    is_read_only = SD_CheckReadOnly(card);
-
     ret = SdioBusInit(&sdio_bus, SDIO_BUS_NAME);
     if (ret != EOK) {
         KPrintf("Sdio bus init error %d\n", ret);
@@ -352,6 +444,7 @@ int Imxrt1052HwSdioInit(void)
     }
 
     sdio_dev.dev_done = &dev_done;
+    sdio_dev.haldev.dev_block_control = SdioControl;
     ret = SdioDeviceRegister(&sdio_dev, SDIO_DEVICE_NAME);
     if (ret != EOK) {
         KPrintf("Sdio device register error %d\n", ret);

Ubiquitous/XiZi/board/ok1052-c/third_party_driver/uart/connect_uart.c

@@ -41,11 +41,9 @@ void LPUART1_IRQHandler(int irqn, void *arg)
 {
     x_base lock = 0;
     // KPrintf("LPUART1_IRQHandler \n");
-    lock = DISABLE_INTERRUPT();
-
+    lock = DisableIRQ(UART1_IRQn);
     UartIsr(&serial_bus_1, &serial_driver_1, &serial_device_1);
-
-    ENABLE_INTERRUPT(lock);
+    EnableIRQ(UART1_IRQn);
 }
 DECLARE_HW_IRQ(UART1_IRQn, LPUART1_IRQHandler, NONE);
 #endif

Ubiquitous/XiZi/board/ok1052-c/third_party_driver/usb/nxp_usb_driver/host_msd_command.c

@@ -15,8 +15,8 @@
 */
 
 /*************************************************
-File name: usb_misc.h
-Description: modify usb_echo to KPrintf
+File name: host_msd_command.c
+Description: modify usb msd command test function
 Others: take SDK_2.6.1_MIMXRT1052xxxxB/boards/evkbimxrt1050/usb_examples/usb_host_msd_command for references
 History: 
 1. Date: 2022-02-10

Ubiquitous/XiZi/board/rv32m1_vega/board.c

@@ -63,10 +63,12 @@ void InitBoardHardware(void)
 
     InitHwUart();
     InitHwTick();
+
+    InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
+
     InstallConsole("uart0", "uart0_drv", "uart0_dev0");
 	KPrintf("console init completed.\n");
 
-    InitBoardMemory(MEMORY_START_ADDRESS, MEMORY_END_ADDRESS);
     KPrintf("memory address range: [0x%08x - 0x%08x], size: %d\n", (x_ubase) MEMORY_START_ADDRESS, (x_ubase) MEMORY_END_ADDRESS, RV32M1VEGA_SRAM_SIZE);
     KPrintf("board init done.\n");
 	KPrintf("start kernel...\n");

Ubiquitous/XiZi/board/stm32f103-nano/board.c

@@ -89,6 +89,8 @@ void InitBoardHardware()
   __set_PRIMASK(1);
   
   InitHwUart();
-	InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
+
 	InitBoardMemory((void*)HEAP_START, (void*)HEAP_END);
+	InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
+
 }

Ubiquitous/XiZi/board/stm32f407-st-discovery/board.c

@@ -156,6 +156,9 @@ void InitBoardHardware()
 #ifdef BSP_USING_UART
 	Stm32HwUsartInit();
 #endif
+
+    InitBoardMemory((void*)MEMORY_START_ADDRESS, (void*)MEMORY_END_ADDRESS);
+
 #ifdef KERNEL_CONSOLE
     InstallConsole(KERNEL_CONSOLE_BUS_NAME, KERNEL_CONSOLE_DRV_NAME, KERNEL_CONSOLE_DEVICE_NAME);
 
@@ -166,8 +169,6 @@ void InitBoardHardware()
     KPrintf("\nconsole init completed.\n");
     KPrintf("board initialization......\n");
 #endif
-    
-    InitBoardMemory((void*)MEMORY_START_ADDRESS, (void*)MEMORY_END_ADDRESS);
 
 	for(i = 0; _board_init[i].fn != NONE; i++) {
 		ret = _board_init[i].fn();

Ubiquitous/XiZi/board/xidatong/Kconfig

@@ -42,9 +42,8 @@ menu "xidatong feature"
 
     menu "config board peripheral"
         config MOUNT_SDCARD
-            bool "mount cd card"
+            bool "mount sd card"
             default n
-            select BSP_USING_SDIO
     endmenu
 
 endmenu

Ubiquitous/XiZi/board/xidatong/board.c

@@ -29,24 +29,6 @@ Modification:
 #include "board.h"
 #include "pin_mux.h"
 
-#if defined(FS_VFS) && defined(MOUNT_SDCARD)
-#include <iot-vfs.h>
-
-/**
- * @description: Mount SD card
- * @return 0
- */
-int MountSDCard(void)
-{
-    if (MountFilesystem(SDIO_BUS_NAME, SDIO_DEVICE_NAME, SDIO_DRIVER_NAME, FSTYPE_FATFS, "/") == 0)
-        KPrintf("sd card mount to '/'");
-    else
-        KPrintf("sd card mount to '/' failed!");
-    
-    return 0;
-}
-#endif
-
 #if defined(SDK_I2C_BASED_COMPONENT_USED) && SDK_I2C_BASED_COMPONENT_USED
 #include "fsl_lpi2c.h"
 #endif /* SDK_I2C_BASED_COMPONENT_USED */

Ubiquitous/XiZi/board/xidatong/third_party_driver/include/connect_sdio.h

@@ -27,11 +27,14 @@
 #include <clock_config.h>
 #include <fsl_gpio.h>
 #include <fsl_common.h>
+#include <connect_gpio.h>
 
 #ifdef __cplusplus
 extern "C" {
 #endif
 
+#define SD_CARD_STACK_SIZE 2048
+
 int Imxrt1052HwSdioInit(void);
 
 #ifdef __cplusplus

Ubiquitous/XiZi/board/xidatong/third_party_driver/sdio/Kconfig

@@ -10,4 +10,15 @@ if BSP_USING_SDIO
     config SDIO_DEVICE_NAME
         string "sdio device name"
         default "sdio_dev"
+
+    config MOUNT_SDCARD_FS
+        bool "mount cd card file system"
+        default n
+        select MOUNT_SDCARD
+
+    if MOUNT_SDCARD_FS
+        config MOUNT_SDCARD_FS_TYPE
+            int "choose file system type : FATFS(0) LWEXT4(3)"
+            default 0 
+    endif
 endif

Ubiquitous/XiZi/board/xidatong/third_party_driver/sdio/connect_sdio.c

@@ -104,9 +104,6 @@ static const sdmmchost_card_switch_voltage_func_t s_sdcard_voltage_switch = {
 };
 #endif
 
-/*! @brief SD card detect flag  */
-static volatile bool s_card_inserted = false;
-
 /*! @brief Card descriptor. */
 static sd_card_t g_sd;
 static int sd_lock = -1;
@@ -142,11 +139,6 @@ static void BoardPowerOnSdCard(void)
     BOARD_USDHC_SDCARD_POWER_CONTROL(1);
 }
 
-static void SdcardDetectCallBack(bool is_inserted, void *user_data)
-{
-    s_card_inserted = is_inserted;
-}
-
 static void CardInformationLog(sd_card_t *card)
 {
     NULL_PARAM_CHECK(card);
@@ -261,6 +253,19 @@ static uint32 SdioWrite(void *dev, struct BusBlockWriteParam *write_param)
     return write_param->size;
 }
 
+static int SdioControl(struct HardwareDev *dev, struct HalDevBlockParam *block_param)
+{
+    NULL_PARAM_CHECK(dev);
+
+    if (OPER_BLK_GETGEOME == block_param->cmd) {
+        block_param->dev_block.size_perbank = g_sd.blockSize;
+        block_param->dev_block.block_size = g_sd.blockSize;
+        block_param->dev_block.bank_num = g_sd.blockCount;
+    }
+
+    return EOK;
+}
+
 static struct SdioDevDone dev_done = 
 {
     SdioOpen,
@@ -269,10 +274,121 @@ static struct SdioDevDone dev_done =
     SdioRead,
 };
 
+#if defined(FS_VFS) && defined(MOUNT_SDCARD_FS)
+#include <iot-vfs.h>
+
+/**
+ * @description: Mount SD card
+ * @return 0
+ */
+static int MountSDCardFs(enum FilesystemType fs_type)
+{
+    if (MountFilesystem(SDIO_BUS_NAME, SDIO_DEVICE_NAME, SDIO_DRIVER_NAME, fs_type, "/") == 0)
+        KPrintf("Sd card mount to '/'");
+    else
+        KPrintf("Sd card mount to '/' failed!");
+    
+    return 0;
+}
+#endif
+
+static void SdCardAttach(void)
+{
+    bool is_read_only;
+    static sd_card_t *card = &g_sd;
+    
+    KPrintf("\r\nCard inserted.\r\n");
+    /* reset host once card re-plug in */
+    SD_HostReset(&(card->host));
+    /* power on the card */
+    SD_PowerOnCard(card->host.base, card->usrParam.pwr);
+    KPrintf("Power on done\n");
+
+    /* Init card. */
+    if (SD_CardInit(card)) {
+        KPrintf("\r\nSD card init failed.\r\n");
+        return;
+    }
+
+    /* card information log */
+    CardInformationLog(card);
+
+    /* Check if card is readonly. */
+    is_read_only = SD_CheckReadOnly(card);
+
+#ifdef MOUNT_SDCARD_FS
+    /*mount file system*/
+    MountSDCardFs(MOUNT_SDCARD_FS_TYPE);
+#endif
+}
+
+static void SdCardDetach(void)
+{
+    /*unmount file system*/
+    KPrintf("\r\nCard detect extracted.\r\n");
+
+#ifdef MOUNT_SDCARD_FS
+    UnmountFileSystem("/");
+#endif
+}
+
+static uint8 SdCardReadCd(void)
+{
+	BusType pin;
+
+    pin = BusFind(PIN_BUS_NAME);
+
+    pin->owner_haldev = BusFindDevice(pin, PIN_DEVICE_NAME);
+
+    struct PinStat PinStat;
+
+    struct BusBlockReadParam read_param;
+    read_param.buffer = (void *)&PinStat;
+
+    PinStat.pin = IMXRT_GET_PIN(2, 28);
+    
+    return BusDevReadData(pin->owner_haldev, &read_param);
+}
+
+static void SdCardTask(void* parameter)
+{
+    static int sd_card_status = 0;
+
+    while (1) {
+        if (!SdCardReadCd()) {
+            if (!sd_card_status) {
+                SdCardAttach();
+                sd_card_status = 1;
+            }
+        } else {
+            if (sd_card_status) {
+                SdCardDetach();
+                sd_card_status = 0;
+            }
+        }
+    }
+}
+
+#ifdef MOUNT_SDCARD
+int MountSDCard()
+{
+    int sd_card_task = 0;
+    sd_card_task = KTaskCreate("sd_card", SdCardTask, NONE,
+                           SD_CARD_STACK_SIZE, 8);
+    if(sd_card_task < 0) {		
+		KPrintf("sd_card_task create failed ...%s %d.\n", __FUNCTION__,__LINE__);
+		return ERROR;
+	}
+
+    StartupKTask(sd_card_task);
+
+    return EOK;
+}
+#endif
+
 int Imxrt1052HwSdioInit(void)
 {
     x_err_t ret = EOK;
-    bool is_read_only;
     
     static struct SdioBus sdio_bus;
     static struct SdioDriver sdio_drv;
@@ -304,35 +420,6 @@ int Imxrt1052HwSdioInit(void)
         KPrintf("\r\nSD host init fail\r\n");
         return ERROR;
     }
-
-    KPrintf("\r\nPlease insert a card into board.\r\n");
-
-    /* power off card */
-    SD_PowerOffCard(card->host.base, card->usrParam.pwr);
-
-    if (SD_WaitCardDetectStatus(SD_HOST_BASEADDR, &s_sdcard_detect, true) == kStatus_Success) {
-        KPrintf("\r\nCard inserted.\r\n");
-        /* reset host once card re-plug in */
-        SD_HostReset(&(card->host));
-        /* power on the card */
-        SD_PowerOnCard(card->host.base, card->usrParam.pwr);
-        KPrintf("power on done\n");
-    } else {
-        KPrintf("\r\nCard detect fail.\r\n");
-        return ERROR;
-    }
-
-    /* Init card. */
-    if (SD_CardInit(card)) {
-        KPrintf("\r\nSD card init failed.\r\n");
-        return ERROR;
-    }
-
-    /* card information log */
-    CardInformationLog(card);
-
-    /* Check if card is readonly. */
-    is_read_only = SD_CheckReadOnly(card);
     
     ret = SdioBusInit(&sdio_bus, SDIO_BUS_NAME);
     if (ret != EOK) {
@@ -352,6 +439,7 @@ int Imxrt1052HwSdioInit(void)
     }
 
     sdio_dev.dev_done = &dev_done;
+    sdio_dev.haldev.dev_block_control = SdioControl;
     ret = SdioDeviceRegister(&sdio_dev, SDIO_DEVICE_NAME);
     if (ret != EOK) {
         KPrintf("Sdio device register error %d\n", ret);

Ubiquitous/XiZi/board/xidatong/third_party_driver/usb/nxp_usb_driver/host_msd_command.c

@@ -15,8 +15,8 @@
 */
 
 /*************************************************
-File name: usb_misc.h
-Description: modify usb_echo to KPrintf
+File name: host_msd_command.c
+Description: modify usb msd command test function
 Others: take SDK_2.6.1_MIMXRT1052xxxxB/boards/evkbimxrt1050/usb_examples/usb_host_msd_command for references
 History: 
 1. Date: 2022-02-10